Construction of compound wall and internal road at Arnala Lighthouse station

Amount

Supplying and stacking of good earth at site including royalty and carriage upto 5 km (earth measured in stacks will be reduced by 20% for payment), and spreading the same in layers including all labour , tool etc complete as per direction of Engineer-in-charge,(earth measured in stacks will be reduced by 20% for payment)

Dry stone pitching with available hard stone 22.5 cm thick laid in courses and required profile with hammer dressed stones having no side less than 15 cm, with minimum depth of 20 cm including preparing the bedding surface etc. all complete as directed by the engineer in charge.

Providing and laying in position cement concrete of 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 20 mm nominal size) as base courese for cement concrete road excluding the cost of centering and shuttering etc. complete as directed by the engineer in charge.

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete as directed by the engineer in charge.

Providing and fixing in position pre-moulded joint filler 18mm thick 15cm deep in expansion joints with all labour tools and materials etc complete as per direction of Engineer-in-charge

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment).(Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Finishing with Epoxy paint (two or more coats) of approved brand (Asian/ Berger/ Shalimar ) at all locations prepared and applied over guard stone surfaces as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge.

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge In cement mortar

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including refilling/disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed. All kinds of soil.

Dry stone soling/ pitching 22.5 cm thick laid in courses and required profile with hammer dressed stones having no side less than 15 cm, with minimum depth of 20 cm including preparing the bedding surface, supply of all labours , tools, materials etc. complete as directed by the engineer in charge. (Rubble stones obtained from dismantling of masonry)

Providing and laying cement concrete 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) in foundation and plinth including laying, compacting, curing with materials, tools, labours etc. complete as directed by the engineer in charge but excluding the cost of centering and shuttering etc complete as directed by engineer in charge

Construction of stone masonry in foundation & plinth (using old stone obtained from dismantling of masonry) with cement mortar 1:5 (1 cement, 5 sand) below ground level and whenever required and ramming out joints etc. including supply of all labour, materials, tools etc complete as directed by engineer in charge.

Providing and laying in position 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) reinforced cement concrete - All work up to plinth level including the cost of centering, shuttering, finishing and reinforcement etc complete as directed by engineer in charge

Reinforced cement concrete work 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, including cost of centering, shuttering and finishing etc complete as directed by engineer in charge

Supply, fabrication, hoisting and placing in position HYSD reinforcement bars (TATA/ Jindal/ SAIL) conforming to IS 1786 - Latest Edition Grade FE 415 as per detailed drawing and specifications including cutting, bending and tying with 18 SWG binding wire complete for all heights and depths etc. complete including supply of all labours, tools, materials etc. complete as directed by the engineer in charge.

Providing and fixing up to floor five level brick masonry including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete including supply of all labours, tools, materials etc. complete as directed by the engineer in charge.

Providing and laying cement concrete in 1:1½:3 (1 cement : 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).in coping of compound wall and main gate pillars, up to floor five level including supply of all materials, tools, labours etc. complete as directed by the engineer in charge.

Providing and fixing Main Gate with G.I. Pipe ‘C’ class and M.S. flats & plates of size 3.70 m x 2.00 m (as per drawing no. B/4040 design) or as directed including cost of fabrication, transportation, fixing in position, fixing the rails and painting two coats with synthetic enamel paint over one coat of red oxide primer etc. including supply of all labours, tools, materials and finishing etc. complete as directed by the engineer in charge.

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge including supply of all labours, tools, materials, etc. complete as directed by the engineer in charge.

Applying priming coats with water thinnable cement primer on wall surface having VOC content less than 50 grams/litre of approved brand and manufacture to give an even shade etc. wherever required including supply of all materials, labours, tools, scaffoldings etc. complete as directed by the engineer in charge.

Finishing walls with 1st quality Premium Acrylic Smooth exterior paint with Silicone additives of required shade (Asian/ Snowcem/ Berger) on new work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) at all heights to give an even shade etc. wherever required including supply of all materials, labours, tools, scaffoldings etc. complete as directed by the engineer in charge.

Providing and fixing of broken glass pieces on top of the compound wall / Coping with cement mortar 1 : 2 (1 cement : 2 fine sand) and finishing etc. complete including supply of all labours, materials, tools etc. complete as directed by the engineer in charge.

Providing, Supplying and fixing Department emblem in granite plate of size 90 cm x 120 cm (3' x 4') engraving the emblem and letters of approved size with golden colour in granite plate as per drawing no. B/3005 and as directed, including cost of all materials, Tools & Plants, labour charges, fixed in position and finishing etc. complete as directed by the engineer in charge.

Providing, Supplying and fixing of Lighthouse/ Department name board in black granite plate of size 61 cm x 45.7 cm (2' x 1' 6") in three languages (English, Hindi and local language of the state) with engraving letters of approved size with golden colour in granite plate as per drawing no. B/3006 and as directed, including cost of all materials, Tools & Plants, labour charges, fixed in position and finishing etc. complete as directed by the engineer in charge.

JAI CONSTRUTION CO.

LUCKY DECOR