Construction of Assam type Structure for Hostel accomodation over the terrace of Circular building, JMC AND H, Jorhat

Amount

DISMANTLING & DEMOLISHING Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer in-charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 15.7.4. In cement mortar

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. 5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 11.41A.1.1 Size of Tile 600 x 600 mm (Double charge )

Size of Tile 600x600 mm ( Matt / Anti skid )

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

12 mm cement plaster on the rough side of single or half brick wall mix: 13.2.1. 1:4 1 cement : 4 fine sand)

12 mm cement plaster of mix : 13.1.1. 1:4 1 cement: 4 fine sand

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with water proofuig cement paint of required shade : New work (Two or more coats Applied @ 3.84 kg/10sqm

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade 13.47.1. New work (Two or more coats applied @ 1.43 ltr/10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). 9.1.3 Kiln seasoned and chemically treated hollock wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer in-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. 9.120.2 30 mm thick pre laminated PVC door shutters

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 9.48.1. Fixed to steel window‘s by welding:

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 9.96.1 300x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 9.97.3 200x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 9.100.2 100 mm

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Rebaring 20 mm dia bar

16mm dla bar

12 mm dia bar

10 mm dia bar

Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with Bitumen and G.I, limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two costs of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 12.1.3 0.63 mm thick with zinc coating not less than 275 gm/ m²

Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately)

Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer-in-charge.

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Sizo 595x595mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (niinimuin) as per IS 8223:1987, Light reflectance of 85% (minimum)

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 8.3.2 Granite work

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.3.1 W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.4.4 Range of four urinal basins with 10 litre white P.V.C. automatic flushing cister

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 17.7.1 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 17.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. 17.69.1 Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms

Providing and fixing PTMT Bottle Trap for Wash basin and sink. 17.70.1 Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conformingType A, including jointing with seal ring conformingto IS : 5382, leaving 10 mm gap for Single socketed pipes 12.41.1. 75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap 12.42.5 Bend 87.5° 12.42.5.1. 75 mm bend

110 mm bend

Single tee without door 12.42.4.1. 75x75x75 mm

l10x110x110 mm

Coupler 12.42.1.1. 75mm

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm completed, including cost of cutting and making good the walls and floors ( a) 110 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 18.7.3. 25 mm nominal outer dia .Pipes.

40 mm nominal outer dix Piyes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia .Pipes.

Providing and fixing brass bib cock of’approved qualits 15 mm nominal bore ( Two way)

Providing and fixing C.P. brass shower rose with 15 or 20 min inlet : 100 mm diameter

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. 1.10.3. Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 1.14.2. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 1.24.1 5/6 amps switch

15/16 amp switch

3 pin 5/6 amp socket outlet

6 pin 15/16 amp socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 2.2.15. 200 Amp, 36KA, FPMCCB

400 Amp, 50KA, FPMCCB

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2.4.3. 8 way (4 + 24), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.10.1Single pole

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.13.3. 100 amps

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying of following sizes XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 1.1 KV grade, 3 1/2 x 70 sq mm conforming to IS 7098 (Part-I)/ 1988 with amendment up to date etc as required. 3&1/2 x185 sq. mm, 1.1 KV grade Al. conductor armoured UG Cable.

Suppl. Including installation, Commissioning of vermin and dust proof totally enclosed cubical indoor type floor/wall mounting compartmentalize panel board of size 1.35mm x 1.2mx0.4 m made of 16SWG (1.66 mm thick) C.R. sheet and 35mm 35mmx 5mm size angel having 4 no legs at the bottom complete painting with 2 coats of Red Oxide metal primer and 2 coats of enamel paint. The panel board is to be erected in 1:3:6 PCC foundation including brick soling / grouting etc. completed neatly wiring done with provision for one no 400A 4 pole MCCB or Switch Fuse unit as incomer and provision for 3 nos DP or TPN out going as specified and directed by the Deptt.

SuppIying, InstaIlation, testing and commissioning of surface mounted LED batten flitting 1200mm length having Lumen efficacy z 120lm/watt, System Lumen output z 2000 lm, Metal housing , CRI z 80, Power factor z 0.9, THD z 10% having suitable diffuser and CCT in between 4000K to 6500 K (i/c both Limits) complete with all accessories etc. directly on ceiling/wall including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor,singIe core cable and earthing etc. as required. 20W Batten Fitting

Supplying including fitting and fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt. as required complete and as directed by the Department SITC of 300/305 mm Exhaust Fan (Make- Usha model- Aeroclean) Rs.1670 /-(GST @18% & discount @30% )

Supplying including fitting and fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessaryconnection as approved by the Deptt. as required complete and as directed by the Department [ without regulator]. 1200 mm sweep ceiling fan (Make- USHA : Model Name :Energia 32 5 star Rs.3750 /-(GST @18% & discount @45%)

FURNITURE & FIXTURES Supply of Steel single bed of size 2012mm x 910mm with height of 453mm and head board and foot board with tube OD 32 x 12mm thick, embossed holes perforation 12 x 4 nos. laying surface of 1 mm thick material finest finish with mosquito net stand (Student room)

Supply of Steel study table of size 2012mm x 910mm with height of 453mm and head board and foot board with tube OD 32 x 12mm thick, embossed holes perforation 12 x 4 nos. Laying surface of 1 mm thick material finest finish with mosquito net stand prelaminated board used in the product is P2 board. The under structure is made of 25.4mm x 254mm, 1.2mm thick finest finish MS ERW tube. The storage shelf is made from 1mm thick finish MS unevenness in the floor. (Student Room)

Supply of Steel Almirah made of 100% powder coated and anti rust free.Size should be 1955x507x1015. (Student Room)

Supply of steel chair make as per approved by the department with seat and back are injection moulded in polypropylene. They are snap fitted on the under structure assembly and fixed with self tapping screws. Back size 38 cm (W) x 25 cm (H). Seat size 40 cm x 41 cm (D). He under structure assembly is a welded frame assay with the upper frame made of dia 1.9 cm (3/4") x 14 BG thick and legs made of dia 1.9 cm (3/4"0 x 16BG thick MSE rw tubes with finest finish. (Student Room)

providing and fixing standard office table of Dimension-1800 X 900 X 750. Strong sturdy desk which can stand alone or be connected to or joined together to build desking systems.This table is a simple built table sturdy can be used for a variety of operations like a writing desk.The desk ia fully pre-laminated particle board melamine finish and smooth liping table is surrly lasts long due to its scratch resistant and water resistant, stain proof and easy maintain spotless cleaning. These are fully (100%) melamine finish and RHS 3 drawer and LHS shutter. (Wardens Room)

Hi-Back Revolving Chair make with Mesh Finish Fabrics seat and back with Nylon twin caster wheels minimum 5 nos of 50mm, Mechanisim should be Central tilt backrest with lumber support of polypropylene at multilever across back backrest is made of one piece injection moulded frame size should be overall height-850mm x Backrest height-500 mm x Backrest width-180mm x Seat height-250mm x Seat width-480mm x Seat ZDepth- 500mm, Chair as per the certified All India Occupation Therapists' Association (AIOTA) and BIFMA. (Warden Room)

Office Steel Almirah make with 100% powder coated and anti rust free size should be - 1955x432x912. (Warden Room)

The structure will be made of particle board.The side panels,top and bottom panels will be of 18 mm thickness and head board and foot board will be of 25 mm thickness. Edge banding will be done on edge of 2mm on visible sides and 0.8 mm on non-visible sides size of the bed will be 78x72 inches with storage. (Warden 2 BHK).

Sofa set-2+1+1 make with 100% solid wood understructure and seat and back Fabric/Leathrette upholestery as per buyer choice. (Warden 2 BHK).

4 SEATER Dining table make with solid teak wood and top should be Glass top should be Glass top. (Warden 2 BHK).

Steel Almirah made of 100% power coated and anti rust free of size should be 1955x507x1015. (Warden 2 BHK).

Any other unseen item of work which are not covered in this BOQ that may be required at site during execution having an estimated provision of Rs.5,29,225.00 (Including GST). The rate for the items will be finaliased as per current DSR/ Market Rate Analysis etc. in proportion to the quoted amount and the estimated amount. Note:- The amount against this item has been kept as a provission for any unforseen/ additional items of works which may arraise during the execution of the work.

SRI BISHNU CHETRY