REPAIR AND MAINT OF INTERNAL ELECTRIFICATION INCLUDING FANS AND GEYSERS AT CADETS LIVING ACCN AND ADMINISTRATIVE BUILDING MH AT NDA KHADAKWASLA

Amount

Repair / maintenance of internal light fitting of any type like tube lights / wall bracket light fittings / ceiling lights / mirror lights/ table lamp lights in its position, testing all the compenents / parts, wiring etc, identifying and replacing the defective components like driver, side holders, holders, Table lamps etc all as directed by Engr-in-charge. Note: (i) The rate against the above mentioned item is deemed for cost of labour only. (ii) Cost of spares like Driver, lamp holder, LED bulb, connector, connection wire etc, capacitor replaced against above mentioned item will be measured & paid for separately under respective items of Sch 'A' here-in-below as supply only. (iii) The contractor's representative will report to concerned JE E/M at 0900hrs daily to collect the list of defects and will submit the completion report on following day before 0900hrs to the JE E/M. (iv) The contractor has to rectify the defects and make the light fittings functional within 24 hours from the time the list of defective lights is handed over to him / his rep by the concerned JE E/M. In case the light fitting is not made functional for whatsoever reason within the specified time limit, an amount of Rs 100/- per such defective light fitting per day will be recovered from the amount due to him through RAR / Final Bill. The repair/maint in Cadets living accommodation (Sqn bldgs) shall be carried out as per the timings convenient to cadets or as directed by Engineer-in-charge and preferably during afternoon and study period. The contractor shall engage separate team of technicians / repairer for each Battalion and a team for Training & admbldgs (v) The contractor shall maintain proper record of repair / maint in a binded register duly bringing out the details of spares replaced on each and every light fitting and get it authenticated from concerned JE E/M on daily basis. The contractor shall put up the maint record register to Engineer-in-charge for inspection every Monday or as and when asked for. (vi) The contractor shall maintain sufficient stock of spares / material required for repair / maint of light fittings with the concerned JE E/M against the supply only items here-in-below. (vii) The Electricians should be ITI (Electrical) qualified and the contractor should submit the copy of certificates of electricians while sigining the site orders.

Supply only Retrofit pendant lamp holders suitable for table lamps or wall bracket light fittings or for ceiling lights

Supply only Brass lamp holder batten type suitbale for E27 base.

Supply only PVC / polycarbonate Angle/Batten type lamp holders retrofit type

Supply only High glow 9W,warm white ,180 degree range LED bulbs B22 base cap all as specified. Make:Luker Cat part:LBPC09CL or equivalent in Bajaj/Philips

Supply only High glow 3W, warm white , LED candle bulbs of E27 base cap all as specified. Make: Luker Cat Part:LBGC03 or equivalent in Bajaj/Philips

Supply only LED bulb 0/1 watt of any color sample given by the Engr-in-charge with B-22 base all as specified. Make: Luker Cat Part:LBCOL05 or equivalent in Bajaj/Philips

Supply only Spring loaded G13 side holders (set of 2) suitable for 36/40W FTL fitting

Supply only LED Electronic driver for 20 watts Make should be as per the Existing manufacturer

Supply only LED Electronic driver for 25/30 watts Make should be as per the Existing manufacturer

Supply only LED Electronic driver for 36/40 watts Ceiling lights Make should be as per the Existing manufacturer

Supply only Retrofit 4 pin 18/20 watt LED PL-L with direct plug and play suited for installation in existing 2G11 lamp holders Make Havells Cat part No. PHOTONULTRAPLL419TL18WLED865SPC or equivalent in Jaquar/Philips

Supply only capacitor of 1.5 mfd for wall fans. Make: Epcos/Tibcon/Crompton

Supply only capacitor of 2.5 mfd for ceiling fan/exhaust fan. Make: Epcos/Tibcon/Crompton

Supply only capacitor of 4 mfd for air circulator/exhaust fan. Make: Epcos/Tibcon/Crompton

S&F in replacement of fan regulator electronic step type suitable for 1200/1400 mm sweep fan as per the sample provided by the Site-in-charge.(Make:Anchor/Vinay)

S&F in replacement of switch piano flush type 5 Amps SP one way all as specified. (Make:-Anchor/Vinay)

S&F in replacement of switch piano flush type 5 Amps SP two way all as specified. (Make:-Anchor/Vinay)

S&F in replacement of switch piano flush type 20 Amps SP one way all as specified. (Make:-Anchor/Vinay)

S&F in replacement of socket combination 5/15 Amps flush mounted 3/5 pin multi purpose all as specified. (Make:Anchor/Vinay)

S&F in replacement of Switch socket combination 5/6 Amps flush mounted 3 pin multi purpose all as specified. (Make:Anchor/Vinay)

S&F in replacement of socket outlet 3 pin 5A flush type complete all as specified. (Make:Anchor/Vinay)

S&F in replacement of socket outlet 2 in 1 3 pin 5 and 15 Amp flush type complete all as specified. (Make:Anchor/Vinay)

S&F in replacement for ceiling rose, 3 terminals /PVC/Polycarbonate, isolated body. Make:Vinay/Anchor Roma

S&F in replacement of modular fan regulator, 2 module, suitable for ceiling fan of 1200/1400mm sweep Make: Roma/Vinay

S&F in replacement of Modular socket 6 A 2/3 Pin 2 module. Make: Roma/Vinay

S&F in replacement of Modular socket 6A/16A - 2/3 Pin 2 Module. Make: Roma/Vinay

S&F in replacement of modular switch 1 way 10 A 1 module. Make: Roma/Vinay

S&F in replacement of modular switch 1 way 20 A 1 module with neon indicator. Make: Roma/Vinay

S&F in replacement for modular switch 2 way 10 A 1 module. Make: Roma/Vinay

S&F in replacement of 1 and 2 module Blanking plates. Make: Roma/Vinay

S&F in replacement junction box one/two/three/four way suitable as per site requirement all as specified and directed by Engr-in-charge.

S&F in replacement of door bell AC 230 volts single phase ding dong type all as specified and directed. Make:Anchor/Vinay

S&F in replacement table lamp fittings white colored suitable for B-22 base cap CFL/bulb with necessary accessories including surface PVC box of circular/square type all as specified. Make: As per the sample provided by the Engr-in-charge

M&L for securing loose wiring and repair to point wiring with necessary rigid non metalic PVC casing caping double lock type ISI marked inclusive all accessories complete as specified and directed.

Taking down carefully copper/aluminium point wiring (light/fan/socket) including all accessories wire, casing caping/conduit, screws etc and making good the disturbed surfaces all as directed

M&L for point wiring with 1.5 sq mm copper conductor FRLS (multistrand) PVC insulated ISI marked unseathed cable and including surface, Non metalic rigid PVC casing capping double lock type ISI marked not less than 25 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 1.5 sq mm copper conductor as earth wire to common earth dolly including PVC box suitable for modular type switches, sockets, fan regulator etc for following :- One light/Fan point controlled by one way switch 6 Amps 240 volts

Ditto as per item No 37 above but One 3 pin 6 Amps socket out let point on independent board.

Ditto as per item No 37 above but One 3 pin 6 Amps socket out let point on same board.

Ditto as per item No 37 above but One light point controlled by two 6 Amp two way switches .

M&L for point wiring with 2.5 sq mm copper conductor FRLS (multistrand) PVC insulated ISI marked unseathed cable and including surface, Non metalic rigid PVC casing capping double lock type ISI marked not less than 25 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 2.5 sq mm copper conductor as earth wire to common earth dolly including PVC box suitable for 15 Amps socket outlet power point independent circuit

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6.3mm thick, burried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia of minimum 15m length by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 in SSR PART-I connected to earthing test point all as specified or indicated including provision of earthing lead protection pipe, PCC earth pit with cover, excavation & earth work, testing on completion etc all as specified and directed by Engr-in-Charge.

M&L for supply, installation, testing and commissioning of chemical earthing maintenance free earthing system comprising of Three numbers of 17.2 mm dia 3 mtr long Earth electrode of low carbon steel electrode with 250 micron copper bonding with 23 kg x 3 bags ECOSAFE carbon based backfill compound and suitable clamp including providing FRP pit cover of size 250mmX250mmX250mm complete as per manufacturer specification complete all a specified and directed by Engineer-in-charge. Note:- (i) Rate included for testing,commisioning including checking of earth continuity and earth result complete all as specified and directed. (ii) Venders are bound to get earthing result upto1 Ohm. (iii) Earth strip beyond 7.5 m shall be measured and paid separately. (iv) Rate is included for boring of earthing in any type of soil/rock. Make: (a) JEF Techno Solutions Pvt Limited (b) Ennov infra solutions (P) Ltd (c) Ashok safe Earthing electrode Ltd

S&F in replacement of GI pipe bracket of 25 mm dia 1.2 mtr long bend to shape for street light fitting made out of 25 mm dia GI light grade pipe fixed on pole using suitable FI clamp including necessary new nut, bolt and washer complete all as specified and directed.

S&F in replacement LED security light fiitting 20 W,IP-65 protection made up of die cast alluminium housing with high power LED as lighting source and lens embeded PC cover having TOP opening seperate driver compartment complete all as specified and directed by Engr-in-charge. Make: Lukar Cat Part:LSTE20(Sleek series) or equivalent in Havells / Crompton

S&F in replacement stator motor suitable for light duty fresh air ventilation fan of any sweep(approx 225/250mm) and replacing plywood of not less than 15mm with duly coated with synthetic enamel paint as per the existing arrangement.

M&L Sub main wiring with PVC insulated FRLS grade cable LT 1100 Volts grade PVC insulated unsheathed, multistranded with stranded copper conductor drawn through & including surface type PVC casing & caping of not less than 25 mm including drawn on wall/ceiling/through stair case/wooden surface with all accessories and incl cutting of existing surfaces of any type and making good to match with the existing surfaces acrylic sheet work after completion alongwith one contineous earth wire and connected to common earth complete all as specified for following sizes of cable :- 2 x 2.5 sq mm with one continuous earth wire of size 2.5 sq mm Note : 2 runs of 2.5 sq mm cable and one run of 2.5 sq mm earth wire and PVC casing/capping will be measured as one meter.

Ditto as per item no 47 above but 2 x 4 sq mm with one continuous earth wire of size 4.0 sq mm Note : 2 runs of 4 sq mm cable and one run of 4.0 sq mm earth wire and PVC casing/capping will be measured as one meter.

Ditto as per item no 47 above but 2 x 6 sq mm with one continuous earth wire of size 6.0 sq mm Note : 2 runs of 6 sq mm cable and one run of 6 sq mm earth wire and PVC casing/capping will be measured as one meter.

Ditto as per item no 47 above but 4 x 4 sq mm with two continuous earth wire of size 4.0 sq mm Note : 4 runs of 4 sq mm cable and two runs of 4.0 sq mm earth wire and PVC casing/capping will be measured as one meter.

Ditto as per item no 47 above but 4x 6 sq mm with two continuous earth wire of size 4.0 sq mm Note : 4 runs of 6 sq mm cable and two runs of 4.0 sq mm earth wire and PVC casing/capping will be measured as one meter.

Taking down carefully sub main wiring of any type and size and making good disturbed surfaces complete as directed.

Taking down ceiling fan/exhaust fan of any sweep for servicing / repairing / maintenance, opening up, identifying and replacing the defective parts, cleaning, greasing,etc, reassembling and hanging up/fixing back at its original position, connecting up and testing complete all as directed.

S&F aluminium fan blade for exhaust fan of any sweep/make as per the sample given by the site-in-charge.

S&F bearing No.6201/6202/6203/ 6204 or any other No matching to the existing size and suitable for ceiling fan/exhaust fan/wall mounted fan of approved make

Disconnecting electric connection and taking down carefully fan of any type and size/sweep as described below, removing the burnt winding of fan motor rewinding with super enarneled copper winding wire of suitable gauge or of matching size to the exisiting wires including all insulating material such as insulation paper sleeve, tape, varnishing etc and reassembling, testing, transporting back to site and refixing to original position all as directed by Engineer-in-charge. Celling fan of size 1200/1400mm sweep.

Ditto as per item no 56 above but Air circulator fans size 600 mm sweep wall mounting Oscillating type

Ditto as per item no 56 above but Wall mounted/Pedstal fans size 350/450 mm sweep Oscillating.

Ditto as per item no 56 above but Exhaust fan of 350/450 mm sweep.

Ditto as per item no 56 above but Exhaust fan of size 600 sweep 3 Phase

Preparation of old surface of exhaust fan of any sweep by removing old paint using paint remover or by burning off using blow lamp and cleaning with cloth and Spray painting complete exhaust fan with superior quality synthetic enamel paint (Smoke gray) after applying primer complete all as directed.

Dittto all as per item no 61 above but Air circulator/Pedestal of size 450/600 mm sweep with superior quality enamel paint (Grey) complete all as directed.

Dittto all as per item no 61 above but Ceiling fan of size 1200/1400 mm sweep with superior quality enamel paint ( Milk White) complete all as directed.

S&F in replacement MCB DB sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar, flush/surface mounting complete including taking down the existing DB of any type & size by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site of following type: 04 way SPN DB (double door)

Dittto all as per item no 64 above but 08 way SPN DB (Double door)

S&F in replacement factory made epoxy powder coated Distribution Board TP & N 4 way double door (VTPN MCCB DB) MCCB as In comer, and MCB as outgoing with metal door (IP-43 protection) fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockout semi flush to wall and making good disturbed surface and touch up with the same finishes complete all as specified Note: MCCBs and MCBs will be measured and paid seperately under respective Sch A item in the schedule

Ditto all as per item no 66 above but TP & N 6 way double door (VTPN MCCB DB)

Ditto all as per item no 66 above but TP & N 8 way double door (VTPN MCCB DB)

S&F in replacement of MCB single pole 6-32 Amps working on 240 volts, 50 HZ AC, 10 KA 'C' curve all as specified and directed.

S&F in replacement of MCB DP 6-32 Amps working on 240 volts, 50 HZ AC, 10 KA 'C' curve all as specified and directed.

S&F in replacement of MCB SPN 40- 63 Amps working on 240 volts, 50 HZ AC, 10 KA 'C' curve all as specified and directed.

S&F in replacement of MCB TPN 40-63 Amps working on 415 volts, 50 HZ AC, 10 KA ,'C' curve all as specified and directed.

S&F in replacement of MCB TP 40-63 Amps working on 415 volts, 50 HZ AC, 10 KA ,'C' curve all as specified and directed.

S&F MCCB with rating of 100 Amps,415Volts 3pole with 16kA breaking capacity,thermal magnetic asdjustable of overload & short circuit release as per IS-13947 & IEC 60947-2 & the service short circuit breaking capacity (Ics) should be equal to ultimate breaking capcity(Icu).MCCB should be with suitable spreaders and phase barriers for each terminals.

S&F MCCB with rating of 125 Amps,415Volts 3pole with 16kA breaking capacity,thermal magnetic asdjustable of overload & short circuit release as per IS-13947 & IEC 60947-2 & the service short circuit breaking capacity (Ics) should be equal to ultimate breaking capcity(Icu).MCCB should be with suitable spreaders and phase barriers for each terminals.

S&F of ceiling fan of sweep 1200mm, 240 volts of not less than 3 star BEE rating milk white coloured connecting up with twin core 1.0 sqmm cable from ceiling rose including required length of hanging rod all as specified. Make Crompton, Orient or Havells (Old fan should be deposied in MES Store)

S&F of metal body high speed exhaust fan of 225 mm sweep inclduing replacing the plywood as per the site requirement.

S&F of Plastic ventilation fan of 200 mm sweep inclduing replacing the plywood as per the site requirement.

S&F in replacement of high speed wall mounted fan of sweep 400 mm,,Full copper motor,auto thermal overload protection,compact style and powder coated gurads & pull cord switch for speed regulation and oscillation control including connectng up the power cord to the socket and necessary fixing accessories all as specified and directed. Make:Crompton or equivalent in Havells/Bajaj

S&F metal body Three phase heavy duty exhaust fan 600 mm or 24" sweep inclduing replacing the plywood and fixing with fastner,washer as per the site requirement. Make Havells/Bajaj/Almonard

Disconnecting and taking down existing userviceable geyser of 100 ltrs capacity, taking it to civil workshop for repairing.Opening the geyser and dismanting all parts and taking out inner tank/container, removing dents making to shape including welding / brazing the leakage portion, filling the portion between inner tank and out casing of geyser with new glass wool heat insulating material . Reassembling and painting the outer casing of geyser with two coats of superior quality synthetic enamel paint(existing colors) and re- fixing to original place all as directed.

M&L in replacement safety valve(dead weight) suitable for geyser of 100 ltrs capacity of any type and brand of geyser.

M&L in replacement thermostat 0-70ºC suitable for geyser of 100 ltrs capacity of any type and brand of geyser. Make:As per the sample given by site-in-charge

M&L in replacement heating element of capacity 3 KW,ISI marked of any type and shape suitable for 100 ltrs capacity geysers of any brand / make. Make:As per the sample given by site-in-charge

M&L in replacement heating element of capacity 3 KW,ISI marked of any type and shape suitable for solar water heater system of any brand / make.

M&L in replacement flow unit (inner pipe assembly) suitable for geyser of 100 ltrs capacity vertical type of any geyser brand including rubber ring/gasket.

S&F in replacement GI mesh hot water connection 900 mm long including necessary washers suitable for geysers of various capacities complete all as specified and directed.

S&F in replacement sheet metal enclosures Single pole MCB 20 Amps with a two pin and earth plug and socket complete with all accessaries etc all as directed by Engr-in-charge. Make: Legrand/C&S/Havells

S&F in replacement sheet metal enclosures Triple pole and earth encolsure with a three pin and earth plug with socket complete with one triple pole MCB 32 Amps with all accessaries all as directed by Engr-in-charge. Make: Legrand/C&S/Havells

S&F in replacement sheet metal enclosures Triple pole and neutral and earth encolsure five pin with socket complete with one TPN MCB 63 Amps with all accessaries all as directed by Engr-in-charge. Make: Legrand/C&S/Havells

S&F in replacement neon lamp indicator square/round type.

S&F in replacement PVC insulated round cable 3 core stranded copper conductor 2.5 sqmm as in connection cord of the geyser. Make : Polycab / Havells

S&F in replacement metal clad plug top 3 pin, 20 amps, ISI marked heavy duty for geyser connection cord. Make:Legrand/Havells/C&S

S&F in replacement plug top 3 pin, 15/16 amps, 230 volts, ISI marked heavy duty for geyser connection cord.

S&F in replacement plug top 3 pin, 5 amps, 230 volts, ISI marked heavy duty for geyser connection cord.

M&L in replacement of ply wood sheet of 19 mm thickness for cover the MCB DBs and cutting to the size as required at the site including fixing the same with necessary nuts and bolt arrangement

M&L for repalcing the down rod of ceiling fans with 5 feet GI pipe mudium grade of existing size ceiling fan hanging down rod with necessary clamp accessories all as directed.

M&L in replacement of acrylic sheet of 4mm thickness cutting to the size as required at the site including fixing the same with necessary screw arrangement.

S&F in replacement PVC insulated cable 2 core stranded copper conductor 0.5 sqmm FRLS grade all as specified and directed by Engr-in-charge. Make : Polycab / Havells

S&F in replacement PVC insulated cable 2 core stranded copper conductor 1 sqmm FRLS grade all as specified and directed by Engr-in-charge. Make : Polycab / Havells

Fixing only the ceiling fan of any sweep and connecting up including provision of twin core flexible copper cable from ceiling rose or connector to fan all as specified. (Note:Ceiling fan will be issued under Sch 'B' store free for fixing only)

Fixing only the exhaust fan of any sweep and connecting up including provision of twin core flexible copper cable from ceiling rose or connector to fan including repalcing the old plywood with new one of suitbale size as per site all as specified. (Note:exhaust fan will be issued under Sch 'B' store free for fixing only)

M&L in replacement for fixing the LED strip outdoor type warm white colored 14.4 watt,220V including fixing the strip on any type of surface using necessary clamp accessories. Make:Luker Cat part: LSO5050 or equivalent in Philips/Wipro/Havells

S&F in replacement of LED strip outdoor connector 220V with PIN

S&F in replacement of honor board LED (6500K) fitting of 12W individual lenses, silver chrome coloured. Make: Luker LMCL12 or equivalent in Philips/Wipro

S&F LED tube light with diffused optics ultra bright LED tube light (Single side connection) 20 watt with high efficiency,integrated aluminum heat sink suited for installation in existing T8 tube light with G13 lamp holders all as specified. Make: Havells Cat part no PHOTONULTRA2.01213T8SSTL20WLED865SPC or equivalent in Luker/Philips

S&F in replacement 1x20W, 230V surface and wall mounted batten suitable for installing LED Tube including connecting up with twin core twisted flexible copper condctor cable from ceiling rose all as specified . Make: Luker Cat part No. LLTB or equivalent in Crompton/Wipro

S&F 1x10W,230V, LED batten suitable for indoor application of color temperature 6000K surface /wall mounted LED batten including connecting up with twin core twisted flexible copper conductor cable from ceiling rose all as specified . Make:Luker/Havellls/Crompton

S&F in replacement 1x20W,230V surface and wall mounted T5 LED batten ,extruded aluminium housing provided for efficient heat dessipation 1700 lumen output with color temperature 6500K including connecting up with twin core twisted flexible copper conductor cable from ceiling rose all as specified. Make: Luker Cat part no LTM20 or equivalent in Havells/Philips

S&F 1x20/18 W,230V, (warm white) LED batten suitable for indoor application of color temperature 3000K surface /wall mounted LED batten including connecting up with twin core twisted flexible copper conductor cable from ceiling rose all as specified. Make: Luker Cat part no LTM20 (WW) or equivalent in Havells/Philips

S&F 1x10W,230V, (warm white) LED batten suitable for indoor application of color temperature 3000K surface /wall mounted LED batten including connecting up with twin core twisted flexible copper conductor cable from ceiling rose all as specified . Make:Luker/Havellls/Crompton

S&F in replacement environment friendly, energy efficient, aesthetically designed, surface ornamented with rings, moulded body, ceiling light LED fixture with diffuser to give glare free light 15 watt LED. Make -Luker Cat Pt No LIPSRS15 or equivalent in Philips or Havells

S&F in replacement 40 W suspended LED Light with high efficiency providing soft-light and glare free symmetrical illumination including suspension kit including connecting up with twin core twisted flexible copper cable from ceiling rose to fitting complete all as specified and directed. Make: Havells Cat part No. CONSTA1144LP40WLED840SPCWH or equivalent in Luker/Philips

S&F in repalcement recess type LED ceiling lights 20 W LED with ceiling cut out of Ø 160 mm, 6000K Environmental friendly, energy saving, recess mounted downlighter with electronic driver including connecting with twin core wire, including cutting the existing false ceiling dia to the required size and also matching to the adjacent false ceiling surfaces carefully all as specified and directed. Make: Luker cat part no. LDR20 or equivalent in Havells/Philips

S&F in repalcement surface mounted LED Panel lights size of 600mm x 600MM x 35mm 40 W LED 5700K, 240Volts and glare free symmetrical illumination suitable for ceiling, Environmental friendly, new generation, energy saving, high power LED as a light source with clear diffuser and separate replaceable electronic driver including connecting with twin core wire and also matching to the adjacent ceiling surfaces carefully all as specified and directed. Make:Luker Cat part No. LNPSRS40 or equivalent in Philips/Havells Note: The quoted price shall include the cost of Light and its driver.

S&F in repalcement surface mounted LED Panel lights size of 1200mm x 300MM x 35mm 48 W LED 5700K, 240Volts and glare free symmetrical illumination suitable for ceiling, Environmental friendly, new generation, energy saving, high power LED as a light source with clear diffuser and separate replaceable electronic driver including connecting with twin core wire and also matching to the adjacent ceiling surfaces carefully all as specified and directed. Make:Luker Cat part No. LNPSRS48 or equivalent in Philips/Havells Note: The quoted price shall include the cost of Light and its driver.

S&F in replacement Focus light LED 7 watt suitable for mounting on wall/ceiling all as specified and directed. Make: Luker Cat part no. LSP07 or equivalent in Wipro/Philips.

S&F in replacement for white cover plate with frame 18 module. Make:As per the sample given

S&F in replacement for white cover plate with frame 12 module. Make:As per the sample given

S&F in replacement for white cover plate with frame 8 module. Make:As per the sample given

S&F in replacement for white cover plate with frame 6 module. Make:As per the sample given

S&F in replacement for white cover plate with frame 4 module. Make:As per the sample given

S&F in replacement for white cover plate with frame 3 module. Make:As per the sample given

S&F in replacement for white cover plate with frame 2 module. Make:As per the sample given

S&F in replacement for white cover plate with frame 1 module. Make:As per the sample given

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 18 module.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 12 module.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 8 module.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 6 module.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 4 module.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 3 module.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 2 module.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 1 module.

Sparkh Electricals & Works

Suchit constructions

SONU ENTERPRISES

M/S SHREE CONSTRUCTIONS

KESARI AND SONS