Construction of Executive Engineer Office, S/Z at Berhampur in Ganjam District

Excavation of foundation in hard soil within 50m intial lead and 1.5m initial lift including rough dressing and leveling as per direction of Engineer-in-charge.

Filling in foundation and plinth with sand watered and rammed.

Cement concrete (1:4:8) with 4 cm size hard granite metal in foundation and plinth.

Cement concrete (1:2:4) with 12 mm size crusher broken hard granite chips.

Brick work with Fly Ash Bricks 23 cm x 11cm x 8cm size having crushing strength not less than 75 kg/sq.cm with dimensional tolerance ± 8 percent in cement mortar 1:6 in foundation and plinth per cum.

RCC work M-20 grade with 20mm and down grade black hard granite (crusherbroken)stone chips including hoisting and laying including centering and shuttering etc. complete.

For Ground Floor

(a) Column foundation

(b)Plinth Beam

(c) Lintel

(d) Roof Beam

Column

(f) Chajja

(g) Roof slab

(g) Landing slab

(g) Waist Beam

(g) Steps

For First Floor

(c) Lintel

(d) Roof Beam

Column

(f) Chajja

(g) Roof slab

(g) Landing slab

(g) Waist Beam

(g) Steps

For Second Floor

(d) Roof Beam

Column

(f) Chajja

(g) Roof slab

Supplying, fitting and fixing of Stainless steel of 304 grade in hand railing using 50mm dia of 2mm thick circular pipe with Balustrade of size 32mm x 32mm x 2mm @ 0.90mtr. C/C and stainless square pipe bracing of size 32mm x 32mm x 2mm in 3 rows in stair case as per approved design and specification, buffing, polishing etc with cost,conveyance, taxes of all materials, labour,T&P etc. required for the complete in all respect.

Supplying, fitting and placing uncoated HYSD bar reinforcement complete as per drawing and technical specification.

For Ground Floor

For 1st Floor

For 2nd Floor

RCC Ring for Soakpit

Brick work with Fly Ash Bricks 23 cm x 11cm x 8cm size having crushing strength not less than 75 kg/sq.cm with dimensional tolerance ± 8 percent in cement mortar 1:6 in superstructure per cum.

For Ground Floor

For 1st Floor

For 2nd Floor

2.5cm.grading concrete (1:2:2) on roof slab using 6mm.size CBHG chips on new work

6mm thick cement plaster in C.M(1:4) RCC surfaces finished smooth including closed deep chiping and slury treatment.

For Ground Floor

For 1st Floor

For 2nd Floor

16mm thick cement plaster in C.M(1:6) over brick work inside

For Ground Floor

For 1st Floor

For 2nd Floor

12mm thick cement plaster in C.M(1:6)over brick work out side Plaster

For Ground Floor

For 1st Floor

For 2nd Floor

Priming 1 coat with any approved Primer

For Ground Floor

For 1st Floor inside

For 1st Floor outside

For 2nd Floor inside

For 2nd Floor outside

Finishing wall surface of walls with Acrylic wall putty (Water based) of approved make and finished smooth and even surface to receive painting including cost of scaffolding staging chargeswith cost of all materials taxes, labour T&P etc complete.

For Ground Floor

For 1st Floor

For 2nd Floor

Finishing walls with Weathercoat paint of approved shade on new work to give even shade 2 coats inside

For Ground Floor

For 1st Floor

For 2nd Floor

Finishing walls with Plastic Emulsion paint of approved shade on new work to give even shade 2 coats inside

For Ground Floor

For 1st Floor

For 2nd Floor

Fitting vitrified tiles in floors,treads or steps and landing on 25mm thick bed of cement mortar(1:1) joined with neat cement slurry mixed with pig ments including cost of tiles GF

Fitting vitrified tiles in dadoes skirting and riser of steps on 12mm thick cement plaster(1:3) joined with neat cement slurry mixed with pigments to match the shade of tiles including rubbing &polishing complete including cost of tiles GF

Fitting vitrified tiles in floors,treads or steps and landing on 25mm thick bed of cement mortar(1:1) joined with neat cement slurry mixed with pig ments including cost of tiles FF

Fitting vitrified tiles in dadoes skirting and riser of steps on 12mm thick cement plaster(1:3) joined with neat cement slurry mixed with pigments to match the shade of tiles including rubbing &polishing complete including cost of tiles FF

Fitting granite/chequered tiles in floors,treads or steps and landing on 25mm thick bed of cement mortar(1:1) joined with neat cement slurry mixed with pig ments including cost of tiles GF

Fitting granite/chequered tiles in dadoes skirting and riser of steps on 12mm thick cement plaster(1:3) joined with neat cement slurry mixed with pigments to match the shade of tiles including rubbing &polishing complete including cost of tiles GF

Fitting Ceramic wall tiles in floors,treads or steps and landing on 25mm thick bed of cement mortar(1:1) joined with neat cement slurry mixed with pig ments including cost of tiles

Fitting Ceramic floor tiles in floors,treads or steps and landing on 25mm thick bed of cement mortar(1:1) joined with neat cement slurry mixed with pig ments including cost of tiles

Fitting granite/chequered tiles in floors,treads or steps and landing on 25mm thick bed of cement mortar(1:1) joined with neat cement slurry mixed with pig ments including cost of tiles FF

Fitting granite/chequered tiles in dadoes skirting and riser of steps on 12mm thick cement plaster(1:3) joined with neat cement slurry mixed with pigments to match the shade of tiles including rubbing &polishing complete including cost of tiles FF

Fitting granite/chequered tiles in floors,treads or steps and landing on 25mm thick bed of cement mortar(1:1) joined with neat cement slurry mixed with pig ments including cost of tiles SF

Fitting granite/chequered tiles in dadoes skirting and riser of steps on 12mm thick cement plaster(1:3) joined with neat cement slurry mixed with pigments to match the shade of tiles including rubbing &polishing complete including cost of tiles SF

Supplying and fixing of MS window grill and grill gate including cost of fabrication and cost, conveyance, taxes etc. complete.

Priming one coat with any approved red oxide over iron work

For Ground Floor

For 1st Floor

For 2nd Floor

Painting 2coats with any approved iron paint on new iron work.

For Ground Floor

For 1st Floor

For 2nd Floor

Supplying fitting and fixing of FRP door frame of size 75X100mm including drilling holes in Masonry walls

Supplying fitting of Factory made single Leaf Regid FRP composite door Shutter of 32mm thick,Laminated with GRP skins with wood grain finished fabricates using UV stabilised Isopthalic Gel Coat and layer of 450gsm E-glass chopped strand mat(csm) impregnated with Orthopathalic,Polyster resin including fitting all fixtures like hinges,towerbolt,handle,aldrop with cost,conveyance and taxes of all materials and labour complete

Supplying , fitting and fixing of two track UPVC sliding window of approved make with 6mm thick glass of approved quality complete with frame, shutters and all fitting and fixtures.

Supplying and fixing of Roller blinds by fixing powder coated top channel, bottom channel with bottom end cap, control unit and good quality of 0.60 mm thick fabric of approved design and quality etc. complete.

Supplying , fitting and fixing of openable UPVC doors with door frame of approved make with 6mm thick glass of approved quality complete with frame, shutters and all fitting and fixtures.

Providing, fitting and fixing of false ceiling with 12 mm thick gypsum board, Aluminium anodised T Section No. 3215 with 2'-0" centre to centre, L section No. 1705 up to 15 micron on 4 walls to be fixed by means of steel screw and PVC plug and the Aluminium grid 2'-0" x 2'-0" suspended from ceiling etc. complete. (Data for 14'-6" x 14'-6" = 210.25 sft or 19.53 sqm)

For Ground Floor

For 1st Floor

Providing fitting and fixing up partition walling OEL aluminum anodized sectionNo.9210 and 9207 as single groove and double groove respectively as horizontal and vertical member andOEL section4660 as Tapered clip for fixing up 12mm thick pre laminated board (Nova pan Make) and jointing angle No. 1855 etc.

Filling foundation and plinth with excavated materials.

Recessed wiring to light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor of ISI marked with 20 mm dia non-metalic PVC flexible conduit with 5 Amp, 250 V modular type switch ISI marked and ceiling rose ISI marked mounted on MS box having front modular cover of suitable size , MS modular box with 1.0 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection as per direction of Engineer in Charge. ( Make of wire Finolex / L&T / Anchor / Havels / V Guard )

Group-A

Group-B

Group-C

Supplying and fixing of 5/6 amp one way modular type switch on existing switch box/cover including connections etc as required.

Supplying and fixing of 5 pin 5/6 amp socket outlet modular type on existing switch box/cover including connections etc as required.

Supplying and fixing of 15/16 amp one way modular type switch on existing switch box/cover including connections etc as required.

Supplying and fixing of 6 pin 15/16 amp one way modular socket outlet piano type on existing box/cover including connections etc as required.

Supplying and fixing batten holder/BK angle holder ISI marked including connection etc. as required.

Supplying and fixing of 25 mm PVC conduit along with accessories in recessed wiring including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of 3 pin, 5 amp ceiling rose ISI marked on the existing junction box / wooden block including connection etc. as required

Installation,TestingandCommissioning of pre-wired fluorescent fiiting /compact fluorescent fitting of all sizes complete with all accessories and tube etc. directly on ceiling wall, including connection with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor and earthing as required. (Flood Light, 50W rating)

Installation,TestingandCommissioning of pre-wired fluorescent fiiting /compact fluorescent fitting of all sizes complete with all accessories and tube etc. directly on ceiling wall, including connection with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor and earthing as required. (Tube Light, 22W rating)

Installation, Testing and Commissioning of ceiling fan, including wiring the down rods of standard length (upto30cm) with1.5sq.mm FR PVC insulated single core multistrand copper conductoretc. including providing and fixing phenolic laminated sheet steet cover on the fan box etc as required.

Installation,Testing and Commissioning of resistance type ceiling fan regulator, in existing switch box including connection with 1.5sq.mm FR PVC insulated single core multistrand copper conductor,earthing the regulator as required.

Extra for cutting and threading of G.I. pipe, heavy gauge down rod, for ceiling fan etc. as required.

Providing and fixing of following capacity TP& N disconnector fuse switch unit inside existing cubical panel board with ISI marked HRC fuses including drilling holes in cubical pannel, making connection etc as required.

Supply and fixing of single pole MCB with sheet steel enclosure, distribution board, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, phosphate and powder painted including earthing etc. as required ( But with out MCB/ RCCB/ ISOLATOR) (4 WAY, SINGLE DOOR)

Supply and fixing of 5 amp to 32 amp rating 240 V "B" series miniature circuit breaker suitable for lighting and other loads of the following poles in the existing MCB DB ISI marked complete with connections testing and commissioning etc. as required (SINGLE POLE)

Supply and fixing of 5 amp to 32 amp rating 240 V "C" series miniature circuit breaker suitable for inductive loads of the following poles in the existing MCB DB ISI marked complete with connections testing and commissioning etc. as required. (SINGLE POLE)

Supply and fixing of following rating double pole 240 V isolator in the existing MCB DB ISI marked complete with connection testing and commissioning etc. as required. (40 amp)

Supply and fixing of 5 amp to 32 amp rating 240 V "C" series miniature circuit breaker suitable for inductive loads of the following poles in the existing MCB DB ISI marked complete with connections testing and commissioning etc. as required. (TRIPLE POLE AND NEUTRAL)

Supply and fixing of following rating double pole (single pole and neutral) 240 V residual current break (RCCB) having a sensitivity current up to 300 milli ampere in the existing MCB DB ISI marked complete with connection testing and commissioning etc as required. (25 amp)

Supply, Installation, Testing, and Commissioning of 32 Amp DP Main switches of following capacity (IS 13940 Part 3/1993 ) on existing surface / wall mountnting and complete with HRC Fuse links, interconnections, earthing, etc. as required as per direction of Engineer in Charge. Make SEIMENS/ HPL/ ANCHOR/ L&T/ HAVELS/ C & S/ RK (32 Amp DP)

Earthing with G.I earth pipe 3 meter long 40 mm dia ISI marked including accessories and providing masonary enclosure with cover plate having locking arrangment and watering pipe etc (but with out charcoal and salt ) as required

Extra for using salt and charcoal for G.I or copper pipe earth electrode as required

Providing and fixing to wall or ceiling and floor pvc pipes class conforming to ASTM-D 1785/89(Sch-80) and pipe fittings of thefollowing nominal bore with clamps including making good the wall, ceiling and floor all complete as per specification complete.

15 mm dia PVC Pipe

25 mm dia PVC Pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes conforming to IS:15778, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge

15 mm dia CPVC Pipe

25 mm dia CPVC Pipe

Cutting grooves in pucca floors and walls for taking GI/PVC pipes and making good the damages as per specification complete.

Cutting holes through existing brick work including making good the same in cement mortar (1:4) for taking GI/PVC pipes and fittings etc all complete as per specification.

Fixing of Brass Screw-down Bib Cocks (Taps) polished bright conforming to IS:781-1995 of the following nominal sizes as per specification complete.

15 mm dia C.P. Brass Short Body Bib cock

15 mm dia C.P. Brass long body Bib cock

15 mm dia C.P. flanges (Big)

15mm dia CP extension piece - 25mm long

Fixing of Brass Screw-down Stop Cocks conforming to IS:781-1995 of the following nominal sizes as per specification complete.

15mm dia Brass Screw-down Stop Cock

15 mm dia CP Brass Concealed Stop Cock

20 mm dia CP Brass Concealed Stop Cock

Fixing Rotational moulded polyethylene cylindrical vertical water storage tanks conforming to IS : 12701--1996 including cutting holes through the tank and fixing mild steel tubes and fittings and providing extra sockets and jam nuts, fixing ball valve etc, including hoisting upto a height of 5 metres above ground level and placing the tank to the required position etc all complete as per specification and direction of the Engineer in charge

2000 litre capacity 3 - Layer White Rotational Moulded Cylindrical Vertical water storage tanks (ISI marked)

Providing and fixing on wall face unplasticised Rigid PVC soil, waste and rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes

110 mm dia U-PVC SWR pipes

Providing and fixing on wall face unplasticised-PVC moulded fittings / accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion

Single tee with door 75x75x75 mm

75 mm dia P.V.C. SWR door bend 87.5°

Single tee without door 75x75x75 mm

75 mm dia P.V.C. SWR plain bend 87.5°

Single tee with door 110x110x110 mm

110 mm dia P.V.C. SWR door bend 87.5°

Single tee without door 110x110x110 mm

110 mm dia P.V.C. SWR plain bend 87.5°

75 mm dia PVC SWR coupler

110 mm dia PVC SWR coupler

PVC vent cowl 110 mm

75 mm dia P.V.C. SWR.pipe clip

110mm dia P.V.C. SWR Gully trap

Laying in trenches High Density Polyethylene Pipes conforming to IS 4984 - 1995 and Specials of following outside diameter and Class-1 to Class-3 and jointing by Fusion welding method including testing as per specification complete. (Earth work in trenches to be measured and paid for separately).

90 mm dia H.D.P.E Pipe P.N. 6.0

110 mm dia H.D.P.E Pipe P.N. 6.0

Fixing Wash Down Water Closet (European type W.C pan) with integral ‘S’ or ‘P’ trap conforming to IS 2556 : Part 8-2004, to the floor with wooden plug and chromium plated screws including jointing the trap with soil pipe in cement mortar (1:1) etc all complete as per specification.

White Vitreous China EWC Pattern with "P" Trap

Fixing plastic seat and cover for wash down water closet with chromium plated brass hinges and rubber buffers all complete as per specification.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

Fixing bowl pattern urinal conforming to IS 2556 : Part 6-1996 including connecting the urinal of 430x260x350 mm or 340x410x265 mm sizes respectively with waste pipe by means of white lead mixed with chopped hemp etc all complete as per specification.

Fixing 15mm dia CP urinal spreader all complete as per specification.

Fixing glazed earthenware squatting plate of size 600mm x 350mm conforming to IS:2556- Part-6-1995 with integral longitudinal flushing pipe including embedding the plate in 25mm cement mortar (1:8) laid over 150mm cement concrete (1:4:8) using 40mm hard granite metal all complete as per specification.

Fixing wash basins with hole for pillar taps conforming to IS 2556 : Part 4-2004 with Cast Iron or M S brackets painted white including cutting holes in walls and making good the damages etc all complete as per specification.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required

24"x 18"x 10" STEEL sink single bowl(Ordinary )

Supplying all Materials,labour, T&P fitting,fixing of PVC waste pipe for wash basin or sink i.e Flexible (Coil shaped) PVC Waste pipe 40mm dia with length not less than 700 mm with PVC waste fittings etc. All complete as per specification and direction of the Engineer-in-charge.

Fixing Chromium Plated brass trap of the following nominal diameter for wash basin and sink

Fixing pillar taps capstan head screw down high pressure lettered ‘Hot’ and ‘Cold’ with long screws, shanks and back nuts of the following nominal bore as per specification

15 mm dia CP Pillar Cock

Wall Mixture Non Telephonic Type

Fixing 15mm dia PVC inlet connection pipe and making connection with pillar cocks and supply mains for wash basin complete as per specification

Fixing C.P. grating complete as per specification

Fixing 150x150mm. HCI grating complete as per specification

Fixing standard sized Chromium Plated brass towel rail complete with Chromium Plated brass brackets fixed to wooden plugs with Chromium Plated brass screws, complete as per specification and direction of the Engineer-in-charge.

Fixing standard sized Chromium Plated brass towel ring fixed to wooden plugs with Chromium Plated brass screws, complete as per specification.

Fixing standard sized glass shelf with C.P. brass brackets and guard rails complete, fixed to woden plugs with Chromium Plated brass screws as per specification.

Fixing bevelled edge mirror of superior glass mounted on 6mm thick A.C sheet or plywood sheet and fixed to wooden plugs with chromium plated brass screws and washers complete as per specification.

Fixing (a) Liquid Soap Container – Glass container or Plastic container with Chromium Plated brass lid and brackets fixed to wooden plugs with Chromium Plated brass screws or (b) Chromium Plated brass soap dish complete with Chromium Plated brass brackets fixed to wooden plugs with Chromium Plated brass screws or (c) white glazed tooth brush holder fixed to wooden plugs with Chromium Plated brass screws as per specification.

Liquid Soap holder

C.P. Soap holder / Disc

Fixing standard size Chromium Plated brass or glazed porcelain Toilet paper holder fixed to woden plugs with Chromium Plated brass screws complete as per specification.

Fixing Chromium Plated Brass Shower rose with 15mm or 20mm inlet including polishing all complete as per specification.

Fixing CP Health Faucet with 1.0 1 RM PVC Tube all complete as per specification.

Fixing of Brass or Gun Metal Full Way Valve conforming to IS:781-1995 of the following nominal sizes with wheel as per specification complete.

15 mm dia Brass Full Way Valve

25 mm dia Brass Full Way Valve

32 mm dia Brass Full Way Valve

Cutting the G.I or Black Iron pipes and inserting a fitting.

15 mm to 25 mm diameter

Fixing of Brass Ball Valve (Horizontal plunger type) conforming to IS 1703-1977 as per specification complete. High pressure/Low pressure with copper or PVC floats of the following nominal bore

15 mm dia Brass Ball Valve

32 mm dia Brass Ball Valve

Please Enable Macros to View BoQ information