REPAIR/MAINT TO BRICK WORK, PLASTERING, WALL AND FLOOR TILING, SANITARY FITTINGS, PLUMBING WORK, DOORS AND WINDOW, CHEQUERED/EXTERIOR TILES, PLINTH PROTECTION AND MISC B/R WORK TO TOILETS/BATHROOM/KITCHEN AND ADJOINING AREA ETC AT PEAD WARD, PSY WARD

Amount

Demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and pre cast concrete articles all as directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving n. exc 15 cm thickness (below or above ground level).

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for.

M&L for Brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius with old size bricks built in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:4:8 type D-2 as in foundation and mass concrete using 40 mm graded stone.

M & L for PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in coping, chajja, facia and the like including weathering, slightly rounded or chamfered angles with & incl necessary use and waste of form work for fair faces of concrete

Supply only integral water proofing compound powder ISI marked

S&F in repairs Chromium plated fancy Bib taps with cup , cast copper alloy with crutch handle, screwed for 15 mm bore dia. iron pipe or for brass ferrule and fixed complete all as specified

S&F in repairs Chromium plated fancy long body Bib taps with cup , cast copper alloy with crutch handle, screwed for 15 mm bore dia. iron pipe or for brass ferrule and fixed complete all as specified

S&F in repairs Chromium plated elbow operated fancy long body Bib taps with cup , cast copper alloy, screwed for 15 mm bore dia. iron pipe or for brass ferrule and fixed complete all as specified

S&F in repair cast iron floor trap with chromium plated grating including jointing to waste pipe with cement mortar (75 mm bore of pipe).

S&F in repairs Brass chromium plated shower rose without swivel joints , any size, including fixing to steel pipe or union complete all as specified .

S&F in repairs Chromium plated ,Concealed stop cock Reduced body ISI Marked, , cast copper alloy, screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified

S&F in repair CP Angle stop cock ( one way) long thread with wall flange , fancy type screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified.

S&F in repairs Pillar taps, fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe, high pressure , with or without lettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe

S&F in repairs PTMT( Polytetra Methyllene Terephthalate )Bib taps suitable for 15 mm bore pipe standard of PTMT any colour screwed, for iron pipe and fixed ( Minimum weight 15 mm-90 gms complete all as specified .

S&F in repairs swan neck Pillar taps, fancy type cast copper alloy , chromium plated , screwed down for 15 mm bore pipe, high pressure , with or without lettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe

S&F in repairs elbow operated Pillar taps, fancy type cast copper alloy , chromium plated , screwed down for 15 mm bore pipe, high pressure , with or without lettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe

S&F in repairs CP Angle stop cock( two way) long thread with wall flange , screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed C complete all as specified .

S&F in repairs CP Bib tap with stop cock( two way) long thread with wall flange , screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified .

S & F in repair for Health faucet, chromium plated rising spray with wall brackets with 1.5m long metallic flexible tube, with 15 mm dia complete all as specified and as directed.

S & F in repair for Jet spray, chromium plated rising spray with 1.5m long flexible tube, with 15 mm dia complete all as specified and as directed.

S & F in repair for chromium plated paper holder fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed.

S&F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

S&F sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm

S & F in repairs 15 mm size wall mixer for mixing hot & cold water, cast copper alloy chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 15 mm size central hole basin mixer for mixing hot & cold water, cast copper alloy chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe including 450 mm long braided connection pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repairs CP mild steel gratings suitable for 75/100 mm dia for NT/ FT complete all as specified.

S&F in repairs Chromium plated Brass Tubular towel rod, of 24" (60 cm long) complete all as specified.

S&F in repairs white Vitreous china wash down water closet (pedestal pattern) with fixing bolt, Plastic water closet seat cover, white, closed pattern with flat bottom, and cover with aluminised hinging device, including all connection complete.

Supply and fix in repairs white vitreous china squatting pan ‘ORISSA’ pattern of size 580 mm x 440 mm white with integral foot rests with ‘P’ or ‘S’ trap, front or back inlet including all connection and provision of lime concrete base complete all as specified and as directed..

S&F in repair PVC low level flushing cistern, duel type, valveless, syphonic action type, double push bottom, 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 32 mm dia of required length and making connection complete all as specified.

Supply and fix in repairs Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified.

S&F in repairs PTMT connections 15 mm size with PTMT nuts of length 450 mm complete all as specified.

S&F in repairs PTMT connections 15 mm size with PTMT nuts of length 600 mm complete all as specified.

S&F in repair vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm, white, with grating and union for discharge pipe (excluding flushing cistern, flush pipe), including waste pipe 32 mm size & 600 mm long flexible pipe with PVC coupling complete all as specified.

S&F in repairs Vitreous China urinal flat back, half stall (Large size) with grating and union for discharge pipe (excluding flushing cistern, flush pipe) but including waste pipe 32 mm size & 600 mm long flexible pipe with PVC coupling and all connection complete all as specified.

Supply and fix in repair white vitreous China wash hand basin (Flat back) of size 550 x 400 mm fixed on and including new brackets complete including, 32 mm size brass chromium plated waste coupling, chain and plug and porcelain stopper, waste pipe 32 mm size & 600 mm long flexible pipe with PVC coupling complete all as specified.

S&F in repairs 32 mm size waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly nuts, flange end and fixed complete all as specified fixed.

S&F in repairs 32 mm dia & 600 mm long, flexible PVC waste pipe fixed to WHB / urinals including PVC coupling complete all as specified.

S & F in repairs 20 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete.

S & F in repairs 15 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete.

Taking down Neoprene rubber beading with glass from aluminium joinery and refixing of glass in same opening with new Neoprene rubber beading complete.

S&F 12 mm thick toughened glass ordinary quality and fixed to aluminium joinery with and including neoprene beading, SS clip or cleats of any size any position including taking down of existing unserviceable glass.

M&L for Repairing of existing aluminium door single / double leaf (area of each leaf exc 1 Sqm but n.exc 2.0 Sqm) by taking down tightening of joint, tightening of top & bottom patch, replacement of cleat, screw, oiling and greasing of floor springs, & refixing in same opening for smooth functioning complete all as specified. Note:- Floor door springs where renewed shall be measured and paid separately under appropriate item of BOQ.

M&L for Repairing of existing toughened glass door single leaf (area of each leaf exc 1 Sqm but n.exc 2.0 Sqm) by taking down tightening of joint, tightening of top & bottom patch, oiling and greasing of floor springs, & refixing in same opening for smooth functioning complete all as specified. Note:- Floor door springs where renewed shall be measured and paid separately under appropriate item of BOQ.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty.

S&F in repairs aluminium body (extruded section) body Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters 701 to 850 mm in width and of weight between 36 to 60 Kg and fixed complete.

S&F in repairs Mortise lock vertical type of mild steel 4 levers of size 100 mm with duplicate key all as specified.

M&L for 18 to 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including half round moulding of exposed edge, laid over and including 15 mm thick screed in cement mortar 1:4 and dismantling of old stone slab complete all as specified

M&L for Coloured Glazed ceramic tiles of size 300 mm x 450 mm x 7 mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match with tiles laid over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete.

M&L for Coloured Glazed ceramic exterior wall tiles of 7-8 mm thick area of each tiles exc 0.06 Sqm but not exc 0.11 Sqm, in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match with tiles laid over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete.

Taking down cement plaster of any description on brick or stone masonry wall , etc including racking out joints, hacking for key, scrubbing down with water etc, all as specified.

M&L for Rendering 15 mm thick in cement and sand mortar 1:4 on brick work or cement concrete surfaces of walls including finishing the surface even and smooth with using extra cement and mixing only integral water proofing compound as per manufacturer instruction complete all as specified and as directed by Engineer-in-Charge. Note:- WPC will be measured and paid separately.

M&L for Rendering 10 mm thick in cement and sand mortar 1:6 on brick work or cement concrete wall surfaces including finishing the surface even and smooth without using extra cement complete all as specified.

M&L for Rendering 5 mm thick in cement and sand mortar 1:3 on concrete surfaces of ceiling, including finishing the surface even and smooth without using extra cement complete all as specified.

M&L for preparing new plastered surfaces of ceiling and applying three coats white wash all as specified and directed.

M&L for Preparation of newly plastered surfaces of walls and applying two coat of oil bound distemper over one coat of primer including 2 mm thick cement base wall care putty complete.

M&L for Preparation of newly plastered surfaces of walls and applying two coat of cement base paint over one coat of primer complete.

M&L for preparation of new plastered surface of walls and applying two coats exterior emulsion weather coat paint of make Apex (Asian Paint) / Weather coat (Berger) / Excel Top Guard (Nerolac) over one coat primer complete all as specified and directed.

M&L for Preparation of new steel and iron based surfaces of any description, not otherwise described over 10 cm width or girth, and applying two coat of synthetic enamel paint over a coat of red oxide primer all as specified.

M&L for Preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint all as specified.

M&L for Preparation of old decorated surfaces of walls by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of cement base paint of any tint / shade all as specified.

M&L for Preparation of old decorated surfaces of walls by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of distemper oil emulsion of any tint / shade all as specified.

M&L for Preparation of old decorated surfaces of ceiling by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of distemper oil emulsion of any tint / shade all as specified.

M&L for complete removal of existing treatment of walls and applying two coats of distemper oil emulsion over a coat primer including applying 2 mm thick cement base wall putty complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F rolled mild steel section as in main and cross beams, hip and jack rafters; purlin where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410-W (Gde-E-250 quality A).

S&F in repair Pre- painted galvalume aluminium zinc coating GI based corrugated/plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for 75 mm thick PCC type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in plinth protection laid in bays n. exc. 2 sqm each, finishing the surface of concrete topping even & fair, without using extra cement filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand (all by weight) complete all as specified and as directed by Engineer-in-Charge.

M&L for 18-20 mm thick machine cut Kota stone slab flooring with marble stone strips / slab / tiles as per design approved, over and including cement screed bed 20 mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified.

M&L for 18-20 mm thick machine cut Kota stone slab as in skirting / riser over cement screed bed 10mm thick in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding and rubbish off the premises complete.

M&L for precast cement concrete Type B0,1:2:4 (using 12.5 mm graded stone aggregates) louvres and jallies, 25 mm thick (measured solid), including all mouldings and set in CM 1:4 complete all as specified and directed

M&L for non skid ceramic tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles laid over and including 15 mm thick screed in CM 1:6 (Note : Screed bed will not be measured and paid separately)

M&L for Vitrified ceramic tiles 10 mm thick (square/rectangular) Coloured polished tiles, area of each tile n.exc 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement and pigment to match laid over and including 15 mm thick screeding in CM 1:6 (Note : Screed bed will not be measured and paid separately)

S & F for Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt I. capacity of tank 1000 litres including dismantling of unserviceable existing water tanks of capacity 1000 litres and taken as credit

S & F for Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt I. capacity of tank 500 litres including dismantling of unserviceable existing water tanks of capacity 500 litres and taken as credit

S&F in repair Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed. .(Minimum weight 20mm-210gms) complete all as specified.

S & F in repair white vitreous china floor mounted coupled EWC of size 380 mm x 725 mm x 690 mm including UF soft close slim seat cover, hinges, fixing accessories, accessories set and Cistern Fittings complete all as specified and directed. Make of Cistern & EWC: Jaquar model No-ONS-WHT-10853S300UFSM or equivalent cat No of make mention in list of make

S & F in repairs 15 mm size wall mixer with L bend for overhead shower & provision for hand shower, for mixing hot & cold water, cast copper alloy chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair for auto censor swan neck pillar tap with complete accessories and electrical fittings including removal of existing unserviceable tap and fix new censor tap including installation of new electric point as required and making good the wall tiles, replacement of GI pipe as required complete all as specified and directed.

Material and labour 1st quality vitrified outdoor, parking tiles of approved shade, of size 300 mm x 300 mm x 10 mm thick as in floors / path etc, set & jointed in neat cement slurry & pointed in matching coloured polymer cement based grout to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Taking down pipes (any sizes) incl all fittings

S&F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, or fixed to wall

M&L for Chequered cement concrete coloured tiles 30 cm x 30 cm x 20 mm thick with white cement and pigment, set, jointed and pointed in neat cement slurry laid over and including 15 mm thick screed bed in CM 1:6 as in floors complete all as specified.( (Note : Screed bed will not be measured and paid separately)

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; including dismantling of unserviceable existing tiles complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:4:8, type D-2,(using 40 mm graded stone aggregate) as in Sub base for path / flooring complete all as specified and as directed.

S & F in repair for 20 mm dia curtain rails with brackets and end cap each sides in window / doors, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and as directed. (Each rail will be measured)

Taking up or down 15 mm bore steel tubing and connections, from walls, floors or ceiling etc complete all as specified and as directed by Engineer-in-Charge.

Taking up or down 20 mm bore steel tubing and connections, from walls, floors or ceiling etc complete all as specified and as directed by Engineer-in-Charge.

Refixing of 15 mm bore old steel tubing and connections in new or old position on walls, ceiling or floors etc after cleaning including provn of new fittings all as directed by Engineer-in-Charge (using old steel tubing retrieved from item hereinbefore).

Refixing of 20 mm bore old steel tubing and connections in new or old position on walls, ceiling or floors etc after cleaning including provn of new fittings all as directed by Engineer-in-Charge (using old steel tubing retrieved from item hereinbefore).

S&F 15 mm bore tubes, 'medium grade', galvanised, with all fitting; (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed to wall / ceiling with clips, wall hooks, wooden plugs or laid in floors, complete all as specified.

S&F 20 mm bore tubes, 'medium grade', galvanised, with all fitting; (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed to wall / ceiling with clips, wall hooks, wooden plugs or laid in floors, complete all as specified.

Taking down chowkhat or frame (wooden / aluminium) n. exc. 1.5 Sqm each with shutters (with out taking off shutters from the frame) and taken as credit all as specified and directed.

Taking down chowkhat or frames (wooden / aluminium) with shutters without taking off shutter from the frames exc. 1.5 but n. exc 4 sqm each all as specified and directed.

Taking down shutters of any description n exc 1 sq.m each complete all as specified.

Taking down shutters of any description exc 1 sq.m and n exc 2 sq.m each complete all as specified.

PVC door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with MS square tube, suppling & fixing in opening as per specn & drg

S &F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm with stuck inside with

S&F 250 mm aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminium alloy and fixed

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed, 100 mm length of bolt complete all as specified.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified.

S&F 100mm size butt hinges medium weight (ISI Marked), rolled mild steel complete.

S&F 75mm size butt hinges medium weight (ISI Marked), rolled mild steel complete.

S&F Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge including dismantling of existing frame complete all as specified

S&F in repair aluminium partition fabricated with anodised aluminium section for side & top rail of size 101 mm x 44 mm x 2.5 mm for middle rail (horizontal / vertical) of size 101 mm x 44 mm x 2.5 mm, partly glazed with 5 mm thick tinted glass and partly panelled with 3 mm thick aluminium composite panel including glazing clip, rubber bead, fixed in position as standard practice complete all as directed by the Engineer-in-Charge.

S&F door comprising frame fabricated with aluminium tube with wall thickness 2 mm, shutter frame with C type aluminium section 25 mm size of 2 mm wall thickness, door panel of 3 mm thick aluminium composite panel and neoprene rubber beading as specified and directed by EIC

S&F 3 mm thick aluminium composite panel with glazing clip and neoprene rubber beading and fixed to aluminium joinery including taking down of existing unserviceable glass.

S&F in repair Aluminium grill not less than 3.13 Kg per sqm fixed with frame in windows / ventilator all as specified and as directed at site.

S&F powder coated anodised Aluminium alloy sections sliding windows shutters with frames comprising Series -C (20mm), 3 track sliding shutters duly fitted with neoprene beading, glazing clips, locking device, heat absorbing glass 4.8 mm nominal thickness in 2 shutters and 0.46mm dia SS wire mesh in one shutter complete all as specified and as directed

S&F for anodised Aluminium alloy sections fixed windows shutters with frames of section weight not less than 0.55 Kg/m duly fitted with neoprene beading, glazing clips, locking device, heat absorbing glass 4.8 mm nominal thickness complete all as specified and as directed

S&F aluminium sections ( conforming to IS) door with frame of size 100mm x 44.45 mm wide fabricated with 2 mm thick section, double leaf shutter with 44.45 mm wide fabricated with 2 mm thick section having vertical and top rail 83.50 mm, bottom rail and middle rail 115 mm and including necessary jointing cleats, screws, neoprene rubber beading, PVC packing, tinted glass panes 4.8 mm nominal thickness complete all as specified and as directed.

Hacking out old broken glass, any thickness, size, quality, or description, from frame nexc 1.5 Sqm each pane

S&F for 3.0 mm thick sheet glass ordinary quality and glazing with oil putty nexc 0.5 Sqm each pane

S&F for 3.0 mm thick figured glass ordinary quality and glazing with oil putty n.exc 0.5 Sqm each pane

S&F 4.8 mm thick sheet glass ordinary quality and glazing fixed to aluminium joinery with and including neoprene beading area of each pane exc 0.5 Sqm to 1 sqm.

S & F in repair corner sheet glass shelf of 4.8mm thick fixed with Stainless steel clamps and other necessary fittings suitable for holding in wall corner with minimum 200 mm length in front circular shape, complete all as specified and directed by Engineer-in-Charge.

S&F in repair sheet glass shelf of 4.8mm thick fixed with Stainless steel clamps and other necessary fittings suitable for holding in wall of minimum size 300x150mm , complete all as specified and directed by Engineer-in-Charge.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

NEW BHARAT ENGINEERING AND CONSTRUCTION CO

M K Engineers and Contractors

AJAY CONSTRUCTION

Divya Jyoti Constructions

M/S Reliance Construction

M/S SHIVA CONSTRUCTION

M/S AMARJIT SINGH