REPAIR/REPLACEMENT OF PUMP MOTOR, STARTER AND ALLIED WORKS AT AF STATION UNDER GE(AF) CHABUA

Amount

Taking out pump from its existing foundation by cutting nuts & bolts, blocking the outlet & inlet system by proper plate, decoupling and transportation of pump or part there of to contractor's workshop and back to site, re-fixing, aligning, connecting inlet & outlet pipe after repair and replacement of following parts suitable for centrifugal pump 5 to 7.5 HP. Note:- Labour for opening up of pumps and machinery work and other minor parts required to make the pump functional shall deemed to be included in quoted rate. (i) Ring (Entire) - 01 No (ii) Lantern ring - 02 Nos (iii) Water deflector DE & NDE - 02 Nos (iv) Gasket between lower & upper casing - 01 Set (v) Pump shaft bush SS - 01 No (vi) Ball bearing DE- - 01 Nos (vii) Ball bearing NDE- 01 No (viii) Mechanical Seal - 01 No

Taking out pump from its existing foundation by cutting nuts & bolts, blocking the outlet & inlet system by proper plate, decoupling and transportation of pump or part there of to contractor's workshop and back to site, re-fixing, aligning, connecting inlet & outlet pipe after repair and replacement of following parts suitable for centrifugal pump 10/12 HP. Note :- Labour for opening up of pumps and machinery work and other minor parts required to make the pump functional shall deemed to be included in quoted rate (i) Ring (Entire) - 01 No (ii) Lantern ring - 02 Nos (iii) Water deflector DE & NDE - 02 Nos (iv) Gasket between lower & upper casing - 01 Set (v) Pump shaft bush SS - 01 No (vi) Ball bearing DE-- 01 Nos (vii) Ball bearing NDE- 01 No (viii) Mechanical Seal - 01 No

Taking out pump from its existing foundation by cutting nuts & bolts, blocking the outlet & inlet system by proper plate, decoupling and transportation of pump or part there of to contractor's workshop and back to site, re-fixing, aligning, connecting inlet & outlet pipe after repair and replacement of following parts suitable for centrifugal pump 30 HP. Note :- Labour for opening up of pumps and machinery work and other minor parts required to make the pump functional shall deemed to be included in quoted rate (i) Ring (Entire) - 01 No (ii) Lantern ring - 02 Nos (iii) Water deflector DE & NDE - 02 Nos (iv) Gasket between lower & upper casing - 01 Set (v) Pump shaft bush SS - 01 No (vi) Ball bearing DE- 01 Nos (vii) Ball bearing NDE- 01 No (viii) Mechanical Seal - 01 No

Attending emergency breakdown of where directed, taking out defective centrifugal/mono block/booster (pressure pump) pump set of capacity 0.5/1 HP incl all accessory, transporting pump set from site to work shop for repairs and back and installing the pump set and making water and electrical connection as per existing for running of pump motors complete all as directed by Engr-in-Charge. Note:- (i) Spare Parts shall be measured & paid under relevant items. (ii) Spare parts shall be of OEM or approved Equivalent make.

All as per item No-4 here in before but 5 / 7.5 HP capacity, complete all as specified and as directed.

All as per item No-4 here in before but 10/12.5 HP capacity, complete all as specified and as directed.

All as per item No-4 here in before but 30 HP capacity, complete all as specified and as directed.

M&L for Cutting of old burnt winding and re-winding of electric motor 0.5/1 HP super enamelled copper wire of superior quality as per existing gauge incl varnishing insulating material complete and replacement of defective bearing, greasing, oiling etc incl re-assembling, transporting, fixing in position, making connection, commissioning & testing complete all as specified and directed by Engr in charge.

All as per item No-8 here in before but 5/7.5 HP capacity, complete all as specified and as directed.

All as per item No-8 here in before but 10/12.5 HP capacity, complete all as specified and as directed.

All as per item No-8 here in before but 30 HP capacity, complete all as specified and as directed.

S & F in Replacement of centrifugal pump Cost iron Impeller assembly suitable for 0.5 to 01 HP motor complete all as specified and directed by Engr in charge.

S & F in Replacement of centrifugal pump Cost iron Impeller assembly suitable for 5 to 7 HP motor complete all as specified and directed by Engr in charge.

S & F in Replacement of centrifugal pump Cost iron Impeller assembly suitable for 10 to 12 HP motor all as specified and directed by Engr in charge.

S & F in Replacement of centrifugal pump Cost iron Impeller assembly suitable for 30 HP motor complete all as specified and directed by Engr in charge.

Supply only pump motor coupling for upto 30 HP centrifugal pump set, complete all as specified and as directed.

Supply only gland packing for upto 30 HP centrifugal pump set, complete all as specified and as directed.

Taking out by raising/lowering of submersible sewage pump set of 12 HP make - AQUA with the help of chain pulley block or any suitable means from sewage sump after disconnecting electric and sewage coupling connections, dismantling pump and motor for carrying out repairs /replacement of defective parts, cleaning of impeller and volute casing, clogged discharge line, reassembling, painting the pump set and reinstallation into sewage sump connecting, testing complete to all running parameters all as directed. Note:- (i) Replacement of defective parts, rewinding of motor and Dewatering will be paid separately under respective sch of this work. (ii) Contractor has to make own arrangement for pumping of sewage effluents from sump well as long as pump remains under repair/rewinding by fitting his own pump including other T&P etc , all T&P shall be brought by contractor and nothing will be issued by department. (iii) Rate shall be deemed inclusive of lifting/lowering, transportation of pump etc and other T&P required for the job. (iv) Pump shall be repaired & reinstalled with in 10 days from the date of handing over to contractor.

M&L for rewinding 3 phase, 415V electric motor capacity 12 HP of non clog submersible Sewage pumps. after dismantling the stator and rotor, removing burnt windings, cleaning the slots, rewinding the motor with super enamelled quality hermatic grade copper winding wire of proper gauge and number of turns as per the existing windings, (Class 'F' insulation including Dr. back ELMO-50 Varnish, pre-heating to remove moisture and vaccum pressure impregnated for air bubble free varnishing, with slot liners & separators, fibre - glass sleeves, baking to 150 degree C for 12 hrs in special baking oven to suit the motor for IP-68 protection) of the 12 HP motor reassembling and testing complete all as specified and directed. Note:- Spares/parts to be replaced shall be measured & paid separately under respective items.

S&F in replacement of following parts of existing capacity 12 HP of non clog submersible Sewage pumps complete all as specified and directed. Note:- (i) Spare Parts shall be measured & paid under relevant items as supply only. (ii) Spare parts shall be of OEM or approved Equivalent make.

Supply only Setting plate (clearance adjustment plate).

Supply only Impellers (CI IS 210 with 1.5 to 2% Ni) CF8M.

Supply only Mechanical seal - (out side) lower.

Supply only Mechanical seal - (in side) upper.

Supply only O ring set.

Supply only Lower ball bearing.

Supply only Upper ball bearing.

Supply only Key for shaft.

Supply only Cable gland

Supply only Cable gromate.

Supply only Moisture sensor

Supply only Thermister (Top)

Supply only Auto coupling gasket.

Supply only Oil (IOC OIL-12).

Supply only Auto coupling sliding bracket

Attending emergency breakdown of Raw water Submersible pump house installation where directed, taking out defective submersible pump set of capacity up to 20 HP incl column pipes from bore well, transporting pump set from site to work shop for repairs and back and lowering the pump set incl column pipes and making water and electric connection as per existing for running of pump motors complete all as directed by Engr-in-Charge. Note:- (i) Spare Parts shall be measured & paid under relevant items. (ii) Spare parts shall be of OEM or approved Equivalent make.

M&L in Rewinding of stator of submersible motor for 10/12.5 HP capacity with water proof insulated copper wire of existing gauge to achieve the specified/required RPM including taking out old unserviceable winding, complete all as specified and as directed.

All as per item No-22 here in before but 15/16.5/20 HP capacity, complete all as specified and as directed.

Supply only Upper housing for 10/12.5 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Upper housing for 15/16.5/20 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Mitchel thrust bearing gunmetal V6 for 10/12.5 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Mitchel thrust bearing gunmetal V6 for 15/16.5/20 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Thrust bearing housing for 10/12.5 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Thrust bearing housing for 15/16.5/20 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Half coupling motor for 10/12 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Half coupling motor for 15/16.5/20 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Rotor for V6, 10/12.5 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Rotor for V6, 15/16.5/20 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Bearing bush copper for 10/12.5 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Bearing bush copper for 15/16.5/20 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Gun metal impeller for 10/12.5 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Gun metal impeller for 15/16.5/20 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Pump housing for 10/12.5 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Pump housing for 15/16.5/20 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Pump NRV for 10/12.5 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Pump NRV for 15/16.5/20 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Pump shaft gunmetal for 10/12.5 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Supply only Pump shaft gunmetal for 15/16.5/20 HP Submersible pump & motor (water supply & sewage), complete all as specified and as directed.

Material and labour for lifting of submersible motor pump set (upto 20 HP, 3 phase, 415 volts, 50 Hz) from exixting bore well with the help of chain pulley carefully including submersible cable G I /C I column pipe by unscrewing nuts and bolt from flange joints and staking at site and developing tube well by over pumping for tube well including lowering the submersible pump, GI/CI column pipe and submersible cable to its original position complete after development by compressor and water shall be used only after receipt of satisfactory test result complete all as specified and directed by Engineer -in -charge. Note:- (i) Over pumping will be carried out by pumping the water at higher capacity i.e. not less than 50% above the yield of bore well. (ii) Cost of arranging pump and compressor is deemed to be included in the unit rate Quoted complete all as specified and directed by Engineer -in -charge.

Supply, lowering & jointing in repairs MS EWS column pipe ISI marked, 100 mm dia, 3 meter long heavy grade, 6.0 mm wall thickness, including flange complete with nuts, bolts, washers & rubber gasket including groove for cable entry system complete all as specified and directed.

S&F in repairs single phase preventor and testing complete, complete all as specified and as directed.

S&F in repairs Ampere meter (0-100 )Amps cap direct type/CT type excluding CTs size of 96 x 96 mm square type, complete all as specified and as directed.

S&F in repairs voltmeter (0-500 )Volts square size of 96 x 96 mm flush mounted type with CT coil, complete all as specified and as directed.

S&F in repair's push button ON/OFF switch red/green colour as per existing size/type complete all as specified and as directed.

S&F in repair's LED indicating lamp red, yellow & blue (set of 3) of size as per existing complete all as specified and as directed.

S & F in repair's Electronic Timer for submersible pump starter for 3 phase, 415 volts, complete all as specified and as directed.

S & F in repair's contactor for automatic star delta submersible pump starter for, 3 phase, 415 volts, complete all as specified and as directed.

S&F in repairs Fully Automatic Citation Star Delta Starter in sheet steel Enclosure with NHD contractor & Pneumatic timers, 3 phase 415 volts, Relay range (14-23 Amps) suitable of 30 HP pump, mounting on 40 x 6 mm flat iron clamp grouting in wall (minimum clearance 2" from wall) and connection with ferrules, testing, complete all as specified and as directed by Engr-in-charge.

S&F in repairs Fully Automatic Citation Star Delta Starter in sheet steel Enclosure with NHD contractor & Pneumatic timers, 3 phase 415 volts, Relay range (13-22 Amps) suitable of 5/7 HP pump, mounting on 40 x 6 mm flat iron clamp grouting in wall (minimum clearance 2" from wall) and connection with ferrules, testing, complete all as specified and as directed by Engr-in-charge.

S & F in repair's relay for automatic star delta submersible pump starter overload relay, range (8-22), 415 volts complete all as specified and as directed.

S & F in repair's relay for automatic star delta submersible pump starter overload relay range (16-44), 415 volts complete all as specified and as directed.

Supply and fix in repair's, MCCB 4 pole,415V, 400 Amps with breaking capacity 50 KA, fixed thermal and magnetic settings, complete all as specified and as directed.

Supply and fix in repair's, MCCB 4 pole,415V, 250/320 Amps with breaking capacity 36 KA, fixed thermal and magnetic settings, complete all as specified and as directed.

Supply and fix in repair's, MCCB 4 pole,415V, 100/125 Amps with breaking capacity 25 KA, fixed thermal and magnetic settings, for motor starter protection complete all as specified and as directed.

Supply and fix in repair's, MCCB 4 pole,415V, 50/63 Amps with breaking capacity 25 KA, fixed thermal and magnetic settings, complete all as specified and as directed.

S&F in replacement On load type change over switch open execution of capacity 250/400 Amps 4 Pole 415 Volts complete with handle complete all as specified and directed

S&F in replacement On load type change over switch open execution of capacity 125/160 Amps 4 Pole 415 Volts complete with handle complete all as specified and directed

S&F in replacement On load type change over switch open execution of capacity 63/100 Amps 4 Pole 415 Volts complete with handle complete all as specified and directed

S&F in repairs Main Switch 400 A in sheet steel enclosure type FN (TPN) S-D-F suitable for DIN fuse-link. complete all as specified and directed by Engr-in-charge.

S&F in repairs operating handle kit for ON Load Changeover switch 315A-4 pole . complete all as specified and directed by Engr-in-charge.

S&F in repairs operating handle kit for ON Load Changeover switch upto 160A-4 pole . complete all as specified and directed by Engr-in-charge.

S&F in repairs operating handle kit for ON Load Changeover switch 63A-4 pole . complete all as specified and directed by Engr-in-charge.

Rewiring of LT main panel board for pump motor with 10 Sqmm, 6 Sqmm,4 Sqmm & 1.5 sq mm copper wire with proper size of lugs/sockets/clamps etc complete all as specified and as directed.

S & F in repairs MS sheet covers/doors of any thickness and shape for LT panels including required fabrication, welding, cutting, painting and fixing of hinges as per site requirement complete all as specified and directed.

S & F in repairs mild steel plates covers of any thickness for cable trenches complete all as specified and directed.

S & F PVC insulated and sheathed flat stranded copper conductor of 6 sqmm 3 core water proof submersible cable incl lug and fixed in submersible/monoblock pump set as directed incl taking out old unsv cable, complete all as specified and as directed.

Supplying and laying synthetic Rubber insulated in replacement, mats 2 mm thick for voltage upto 3.3 kv for electrical purpose as per IS 15652-2006, (superseding IS 5424) suitable for electrical shock safety of sizes 2m x 1m complete all as specified and as directed.

S&F in-line booster pump set of upto 0.5/1 HP capacity with all necessary accessories complete all as specified and as directed. Note:- Old unsv pump set of any capacity/make to be keep in MES store.

S&F self priming monobloc pump set of 0.5 hp capacity with all necessary accessories complete all as specified and as directed. Note:- Old unsv pump set of any capacity/make to be keep in MES store.

S&F self priming monobloc pump set of 1 hp capacity with all necessary accessories complete all as specified and as directed. Note:- Old unsv pump set of any capacity/make to be deposit in MES store yard.

Supplying and fixing commissioning and testing submersible pumping set , electrically driven, 415 Volts three phase AC 17.5 HP 11 KW having a discharge capacity of 750 litres per minute at a head of 54 metres, 10 stage delivery 100mm dia complete all as specified and as directed. Note:- Old unsv pump set of any capacity/make to be deposit in MES store yard.

Material and labour in repair for disconnecting of defective air compressor of any capacity including electric motor of capacity of 5 HP 3 phase 50 Hz from pump house , disconnecting electrical connections from main panel and oxidation chamber as per site requirement and refixing after necessary motor hauling , rewinding , greasing, testing and separating the unserviceable parts, cleaning the serviceable parts, re-metalling , polishing and re-assembling including replacement of old parts and necessary painting apply spray paint with two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-charge. Note:- (i) Spare parts required will be measured and paid separately as ''Supply only'' here in after. (ii) Cost of minor spare parts i.e. nuts, bolts and washer are deemed to be included in the quoted rate.

Supply only Piston oil ring

Supply only Piston liner

Supply only bearing

Supply only gear oil

Supply only compressor air meter

Supply only nozzle (air)

Supply only gate valve 15 mm

Supply only Fan belt

Supply only wheel

Supply only adaptor for control valve

Taking out unserviceable mild steel cover of valve pit chamber and supply and fixing covers of valve pit chamber duly hinged fabricating the frame by using 3.15mm thick mild steel sheet and angle iron frame 50mmx50mmx6mm thick including making locking arrangement and fixing the cover in PCC 1:2:4 type B1 using 20mm graded stone aggregate and providing hold fast of appropriate size made to shape of 50mmx6mm flat iron including painting the sheet & frame with two coats of synthetic enamel paint over a coat of red oxide primer all as specified & directed.

Supply & fixing in replacement cast iron body sluice valve heavy duty class ‘PN-1.6’ of 150 mm bore, ISI marked with IS 14846, both flanged ends and drilled, with forged brass spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, complete, all as specified & directed.

Supply and fixing in replacement non return valve heavy duty class ‘PN-1.6 of size 100mm bore, cast iron body, as per IS 5312 (ISI marked), heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint complete all as specified and as directed.

Supply and fixing in replacement non return valve of size 100 mm bore, cast iron body, as per IS 5312 (ISI marked), heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint complete all as specified and as directed.

Supply and fixing in replacement non return valve of size 80 mm bore, cast iron body, as per IS 5312 (ISI marked), heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint complete all as specified and as directed.

Supply and fixing in replacement food valve of size 100 mm bore, cast iron body, as per IS 5312 (ISI marked), heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint complete all as specified and as directed.

Supply and fixing in replacement food valve of size 80 mm bore, cast iron body, as per IS 5312 (ISI marked), heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint complete all as specified and as directed.

Supply and fixing in replacement check valve of size 50/80 mm bore, cast iron body, as per IS 5312 (ISI marked), heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint complete all as specified and as directed.

Supply and fixing in replacement chain pulley block of capacity 2 Ton having anticorrosive stainless steel chain suitable for sewage installation and capable of lifting the load from 15 mtrs complete all as specified and as directed.

S&F in replacement PVC Hose pipe flexible/Spiral for suction /delivery of water supply /sewage as per IS standard, green in colour of pressure 11Kg/Sqcm of Internal dia 80 mm complete with all fixing arrangement complete all as specified and directed.

M&L for painting of LT panel with two coats of synthetic enamel smoke grey paint over after preparation of old surfaces complete all as specified and directed.

M&L for cleaning of the choked casing of non clog submersible pump/column pipe of capacity 12 HP by removing sludge/silt or any solids & refixing the pump/column pipe in position & testing for proper functioning including all T&P required for removal & refixing including dewatering the sump upto desired level with own arrangement complete all as specified and directed.

Earthing complete with galvanized mild steel earth plate electrode 600X600X6 mm thick buried directly in ground vertically (earth pit not less than 2.25 m deep below normal ground level) with the top edge of the earth plate electrode at a depth not less than 1.5m below normal ground level and including GI earth strip 32 x 6 mm bolted (with GI nuts, bolts & check nuts) and riveted to earth plate electrode at one end and nected to metallic bodies of HT/LT equipments etc at the other end, earth strip encased in and including 50 mm bore GI medium grade pipe with all fittings from top of earth plate electrode to body of equipment fixed with and including 25x 6mm flat iron clamps, bolts, nuts and washers and including providing watering pipe 20mm bore GI pipe medium grade from Bottom of concrete pit to top of earth plate electrode including taking down old unsv one complete all as specified and shown in electrical plate No 3 of MES SSR Part-I. The scope of work includes necessary excavation and earth work in any type of soil, removal of soil upto 50 metre, PCC pit with precast RCC cover, charcoal/salt, funnel, CI frame etc complete. NOTES:- (i)The concrete pit shall be made in PCC 1:3:6 type C-1, using 12.5mm graded crushed stone aggregate 40mm thick precast cover slab of RCC (1:2:4), type B-1, using 20mm graded crushed stone aggregate with suitable MS handle in lieu of CI cover shown in electrical plate No 3 of MES SSR Part-I shall be provided. Reinforcement in RCC cover shall be of 8mm dia TMT bars laid @150mm c/c both ways. (ii) Item includes the cost of 7.5 metre GI pipe for protection of earth strip. Any variation in length shall be measured and paid through deviation order. (iii) Item includes cost of 7.5 metre earth strips. Any variation in length shall be adjusted through deviation order. (iv) Earth plate electrode shall be surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides.

M & L for preparing old painted steel or iron surfaces of any size by removing dust, rust with the help of sand paper and applying two coats of synthetic enamel paint on surfaces of machineries, equipment, steel structure at sewage pump and water Supply pump installations etc complete all as specified and directed by Engr in charge. Note:- T&P installed at sewage well No 1 to 03 & Water supply pump house and connected items shall only be measured under this item.

Supply, installation, commissioning and testing in replacement of feeder pillar box type, factory made, CPRI approved, LT(415 Volts, 50 Hz , 3-phase, 4 wire supply) duly mounted on iron leg of size 50x50x6mm, Indoor type, double door, weather and vermin proof (Protection Class IP-54),with ventilation louvers and 2 mm thick MS CRCA sheet and angle iron frame work with both side hinged opening for external, rubber lining, locking arrangement, Powder Coated externally and internally over a coat of red oxide primer complete including grouting of frame with PCC mortor for installation of panel of following:- (At FP 04)

(a) Bus Bar chamber comprising 4 Nos Aluminium strip bus bars air insulated and PVC sheathed, capacity not less than 250 amp with colour coding in separate sheet steel enclosure. (b) MCCB 415 Volts, 125 Amp rating 4 Pole, thermal adjustable type, Service Breaking Capacity 25 kA -1No (d) Change Over switch 125 Amp - 1 No (e)Automatic Star delta starter for 20 Hp submersible electric motor -01 Nos (f) Panel mounted Digital Voltmeter , three phase, 96mm X 96 mm square flush mounted-1 No (g) Panel mounted Digital Ammeter , three phase,, 96mm X 96 mm square flush mounted with suitable ratio of CTs-1 No (h) LED type/Neon type Indicating lamps panel mounting type RYB-3 Nos

(j) Internal wiring with multistranded copper conductor cable/ PVC Insulated aluminium Strip of suitable size incoming to bus bar and bus bar to outgoing MCCB/MCB-1Job. (k) Fine wiring with single core copper conductor cable for instruments/indicating lamps-1 Job. Note:- MCCBs should be connected with spreader terminals of suitable size.

Schedule of Credit

M/s Pramillabh Construction

M/s Sashi Enterprise

kabitaconstruction

M/s PRABIR ENTERPRISE

M/S K S Enterprise

M/S S. P. ENTERPRISE

FREEZCON