(i) Reliability improvement work with Replacement And Rehabilitation of telecom gears and Telecom cables, OFCs in Bangaon-Barasat-Hasnabad-Dumdum Jn.-Rajchandrapur, Sealdah-Ballygunge-Sonarpur-Canning-Baruipur-Namkhana-Diamond Harbour-Budge Budge-Majerhat section of Sealdah division. (ii) Telecom work in connection with replacement of existing Panel Interlocking System with new Electronic Interlocking System at Nischindapur(NCP) Station.

A-NON-SCHEDULE/SOR ITEM vide SL. NO. 1 to 197 GIVEN IN SCHEDULE OF

18 %. GST HAS BEEN SHOWN IN ITEM BREAKUP SEPARATELY.

NON-SCHEDULE/SOR ITEM vide SL. NO. 1 to 197 GIVEN IN SCHEDULE OF WORK INCLUDING GST @ 18 %. GST

HAS BEEN SHOWN IN ITEM BREAKUP SEPARATELY

S No. Item Description of Item Unit Qty Rate Amount

1 1 Excavation of cable trench as per cable route plan, 1.2 cum 4500.00 232.20 1044900.00

Mtr. deep and of 0.3 Mtr. wide at bottom as per RDSO

sketch No. SDO/CABLE LAYING/003 or latest alongside

the track in normal (all type) soil/strata, conforming to

distances as per cable route plan and refilling. This work

includes clearing of route from bushes etc, covering of

cable laid in trench by loose soil for a layer of 50mm

thickness approximately before covering by

bricks(Bricks will be provided by contractor). The work

shall be done as per the extant practice on Eastern

Railway and instructions of Railway Engineer at site.

Note:-(a)for all trenches from distant signal to home

signal and to relay room, the minimum headway above

the uppermost cable in the trench should be 600mm. If

due to a large no. Of cables headway is not available, 4"

of 1:2:4 concreting should be done.

SEALDAH DIVISION-S AND T/EASTERN RLY

2 2 Digging of cable trench 0.3 Mtrs. Deep and 0.3 Mtrs. cum 280.00 421.19 117933.20

Wide on Platform / Road / Hard rocky area. Refilling with

earth leveling of trenches & restoring the original

surface of trenches. The sharp edges will be

smoothened out in bottom of the chase and will be

leveled properly. In hard rocky ground area , cables will

be laid normally on layer of shifted earth of 0.05 mtrs

thickness previously deposited at bottom of the trench

and cables will be covered with layer of sand or shifted

earth of 0.1 mtr thickness. In case sharp edges of rocky

ground cannot be protected from shifted earth then GI/

C I /PVC /DWC/ HDPE pipes will be used, if numbers of

cables is small. In case number of cables are large RCC

duct will be used. In isolated cases, it can be given

smooth surface by using either masonry bricks or

cement concrete. A row of bricks shall then be placed

length wise on the top and jointed with cement mortar

and layer of concrete with cement plaster shall be

provided on top of the same.Note: This item in hard

rocky area will be operated only where normal depth

i.e.1.2 mtr is not possible and it will be decided by site

engineer/unit officer incharge of work.

3 3 Digging of trench 1.2 Mtrs. deep from rail flange/ road cum 210.00 235.59 49473.90

level and 0.3 Mtrs wide and back filling after placing of

DWC/ RCC/GI pipe. (Placing of DWC/RCC/GI pipe covered

separately). The ballast disturbed be screened and

dressed as required by Engineer-in-charge or his

representatives and road tarred immediately. For track

crossing, RDSO sketch No. SDO/CABLE LAYING/009 or

latest and for Road Crossing, RDSO sketch No.

SDO/CABLE LAYING/010 or latest are to be followed.

4 4 Transportation of HDT machine with accessories Metre 150.00 1528.81 229321.50

including handling of stores materials, preparation of

sites and boring for placing of 110 mm dia or 3 Nos

40mm HDPE PIPE or as per site requirement for crossing

of S&T cables together a bridges/culvers, pucca

road/crossing, boring trench shall be minimum 3 (three)

meter below the river bed and 1(one) meter below the

track/road/pucca road crossing area. This includes

supply of HDPE pipes, including accessories, cost of fuel

and all other items etc. which will be required for laying

of cable through it.the work shall be executed as per

instruction of site engineer.HDPE PIPE TO BE SUPPLIED

AS PER RDSO SPEC. Contactor shall provide all material

required for boring and adequate nos. of labours for

proper laying of cables into the bore. Cable shall be laid

cautiously so that it should not get damage due to rough

handling & pressure on cable. Note: Hiring charges of

HDT machine will be bore by contractor.

5 5 Laying of telecom/Signalling cable/Power Cable with Metre 150.00 6.78 1017.00

nylon rope through HDPE pipe and back filling of boring

pit. Note: Cable will be supplied by Railway

6 6 Laying of S&T Cables of various cores/ pairs/ quads in RMT 19600.00 4.24 83104.00

trenches/ GI pipes/ RCC pipes/ HDPE/DWC pipes/

Trunking. This also includes laying of cables in track

crossings & road crossings. Item includes provision of

labels of coloured plastic adhesive tapes or any other

identifiable material on each cable to give the cable

number at each Gantry Post/hectometrepost.(Cables will

be meggered before and after its laying by contractor

under supervision of Railway Representative and the

contractor will submit the meggering report of each

testing). Length of the cable laid includes the length of

the cable coiled for termination purposes. Note: This

also includes laying of Quad/PIJF cable from BPAC/UFSBI

location to SM Room/Relay Room/OFC Room etc. &

Laying of under ground Earth cable as per instruction of

railway representative. Note: Quad/PIJF/Earth cable will

be provided by Railways.

7 7 "Supply of Medium class GI pipes 100 mm dia (4.5 mm Metre 100.00 645.76 64576.00

thickness) as per IS 1239 (Part 1): 2004 or Latest.

Inspection: Consignee"

8 8 "Supply of Medium class GI pipes 50 mm dia (3.6 mm Metre 100.00 342.37 34237.00

thickness) as per IS 1239 (Part 1): 2004 or Latest.

Inspection: Consignee "

SEALDAH DIVISION-S AND T/EASTERN RLY

9 9 "Supply of 'ELBOW'- BENDS to suit GI pipes 50 mm dia Numbers 20.00 90.00 1800.00

(3.6 mm thickness) Inspection: Consignee"

10 10 Laying & Fixing of Medium class GI pipes 50/100 mm dia Metre 200.00 83.05 16610.00

(4.5 mm thickness) & 'ELBOW'- BENDS to suit GI pipes

50 mm dia (3.6 mm thickness) as per IS 1239 (Part 1):

2004 with socket & coupling on culverts bridges or at

any other locations as decided by Site Engineer. It

includes installation of all material required for fixing

arrangement. Contractor will install flexible/corrugated

HDPE pipe at the end of GI pipe along with any masonry

work (if required) to protect the cables from sharp edges

and sudden bends. GI pipe, HDPE & ELBOW'- BENDS will

be provided by railway.

11 11 "Laying of Power Cable/CAT-6/Switch Board Cable/Earth Metre 1600.00 38.14 61024.00

cable/LS cable etc or any other cable in PVC casing

capping of appropriate size. The work also includes

supply and fixing of casing and capping as per

instructions of site incharge. Inspection: Consignee"

12 12 "Supply, Transportation at site and Installation of RCC Numbers 260.00 353.39 91881.40

cable route marker engraved and painted on both side

along the route at every 30 meter and at route

diversion. The cablemarker is to be fabricated as per

CCE/ER's Technical Circular No 108 dated 22.04.24 vide

drawing No.S.I.-S&T/1/2024 (Sheet No.1).The fixing work

is to be done as per extant practice of E. Rly. and as per

rly. site supervisor. Note : (i) Marker shall be placed in

the trench during closing the trench such that there is

no possibility of putting markers at wrong Location. (ii)

Colour Scheme shall be RED for Signal Cable , GREEN for

Quad Joints & YELLOW for OFC Joints. (iii) Engraving on

the RCC marker will be same for all the cables i.e ""ER

S&T CABLES"" Note-The cable route marker to be

provided as per technical circular no. 108 Inspection :

13 13 Closing of Cable Entry Holes by concrete permanently. Job 100.00 100.00 10000.00

All the materials required for the work i.e cement

,Sand,1/4'Stone chips etc. will be supplied by the

14 14 "Supply of half size apparatus case (As per RDSO Numbers 12.00 6661.00 79932.00

drawing No. RDSO/S-11507). This includes supply of

location box (GKP type) with 'E' type lock & key, fitted on

location door on both side, E Type lock as per RDSO Drg.

No. SA 3376 and Key to Drg. No. 3377 as per RDSO

drawing No. RDSO/S-11507. Inspection: Consignee "

15 15 "Casting, concreting and curing of concrete foundation Numbers 12.00 2631.36 31576.32

(in ratio 1:3:6), erection and installation of half size

apparatus case (GKP type) Apparatus Case as per

DRG.NO. RE/S&T/SIG/TENDER /SK/8/85 with 'E' type lock

on CC foundation. This includes cost of all materials

required for fixing holding down bolts, casting,

concreting. Note: - bolts, nuts and washers, bitumen

compound to be supplied by contractor and bitumen

compound to be used in between apparatus case and

foundation as per site engineer. This also includes

bottom of apparatus cases filled with sand and the

outside covered with masonry work and neat cement

plastering. Note: - Location boxes to painted with anti-

corrosive paints as per IS: - 9862-1981, one and half feet

from the bottom, on all surfaces-both inside and outside.

Inspection: Consignee. "

16 16 Painting of two coats of synthetic enamel paint over one Numbers 12.00 200.00 2400.00

coat of primer on the following after scraping & cleaning

surface wherever necessary with contractor's own

supply of paints and primer. Note: The paint and primer

should be from Asian Paints/Nerolac/Dulux/Berger. The

primer/enamel paints(Aluminiun synthetic, black

enamel, brilliant white and yellow) will be as per (IS

5660 of 1970)/(IS 2932 of 1974 or latest) of Apparatus

case Half size. (Outside and Inside).

17 17 "Supply of paper base hylam sheet 12 mm thick. Sqm 7.00 4550.85 31855.95

Inspection: consignee."

SEALDAH DIVISION-S AND T/EASTERN RLY

18 18 Fixing of slotted angle and fixing of hylam sheet (Hylam Numbers 12.00 2118.64 25423.68

sheet will be supplied by Rly) for clamping of cable and

fixing of cable joint on the hylam sheet with earthing of

armour of the quad cables including supply of slotted

angles, wires ferrules for marking and miscellaneous

materials per location to be supplied by contractor.

19 19 "Supply of earth electrode mild steel galvanized, Numbers 12.00 1267.80 15213.60

lightclass, IS:1239(PART-I)-1979.earth electrode pipe

should be with 3 mm thick, 50 mm dia and perforated

(staggered), 5 mm dia holes, 2 nos per 305 mm length

with clamp of MS FLAT(galvanised) of size35 mm x 6

mm (SPEC.NO.226 STD). Earth pipe should include CI

threaded cap. Materials to be procured and designed as

per PCSTE/ER'S DRG. NO. SI/TYP/0097 dated 25.03.2025

or latest. Inspection: - Consignee"

20 20 "Supply of MS FLAT (SPEC. NO. 226 STD or latest) ofsize Numbers 12.00 772.03 9264.36

35 mm x 6 mm with length 5 mtr with holes of 12mm

dia at both ends as per PCSTE/ER'S DRG. NO.

SI/TYP/0097 dated 25.03.2025 (or latest). Note: (The MS

flat with holes may be supplied in equivalent length in

mtrs or as per site requirement). Inspection :

21 21 Fixing of earth electrode including laying and installation Numbers 12.00 983.90 11806.80

of MS flat of size 35 mm x 6 mm with length 5 mtr or as

per extant practice of Eastern Railway. As per

PCSTE/ER'S DRG. NO. SI/TYP/0097 dated 25.03.2025 or

latest for apparatus cases, signal post & other

equipment as per instruction of site engineer. Fixing of

MS flat at apparatus cases/ signal post/other equipment

should be made by the firm at site. Full threaded bolts of

10 mm dia and length 40 mm should be welded in the

apparatus cases in such way that the MS flat at

apparatus case end can be fixed from outside or from

inside. Welding arrangement with accessories and

welding materials should be arranged by the contractor

for fixing of bolts at equipment end where required as

per instruction of Rly. site engineer. All hardware and

other miscellaneous materials required for installation to

be supplied by the contractor except earth electrodes

22 22 "Supply,installation and jointing of Thermo shrink Numbers 45.00 2661.86 119783.70

Universal Jointing kit for Quad Cable/PIJF cable as per

RDSO spec IRS/TC-77/2012 revision 3 and with latest

Amdt. The jointing is to be housed in location box as per

Technical Policy Circular No-107. Inspection: RDSO"

23 23 "Supply of Polyethylene insulated underground railway Kilometre 7.00 241504.00 1690528.00

jelly filled telecom 6-Quad cable of 0.9 mm dia. for S&T

installations as per spec no. IRS:TC 30-2005 Ver 1.0

amendment -5 or latest. Inspection: RDSO"

24 24 "Supply of 20 pair Polythene Insulated Polythene Kilometre 7.00 195500.00 1368500.00

sheathed armoured Jelly filled Telephone cable with

Poly-AL moisture barrier 0.63 mm dia as per

specification No. IRS:TC-41-97 or latest. Inspection :

25 25 Supply of 24 Fibre armoured underground Optic fibre Kilometre 3.00 55250.00 165750.00

cable as per RDSO/SPN/TC/110/2020 Rev.: 0 or latest.

Make: Finolex/Birla or Superior. Inspection : RDSO

26 26 "Supply of 6 Fibre armoured underground Optic fibre Kilometre 3.00 35294.92 105884.76

cable, conforming to TEC Spec.No.

GR/OFC02/03.SEP.2003 or Latest. Make:

Finolex/Mescab/D-Link or Superior Inspection:

27 27 "Supply of 10 pair switchboard indoor copper cable 0.6 Metre 3500.00 41.53 145355.00

dia as per TEC/GR/WIR-06/03. MAR 2002 with latest

Amendments. Make: Finolex/Polycab/Mescab or superior

Inspection: Consignee. "

28 28 Supply of 20 pair 0.4 mm switch board cable as per Metre 1000.00 89.23 89230.00

TEC/GR/WIR-06/03. MAR 2002 with latest Amendments

.Make: Finolex/Polycab/Mescab or superior. Inspection :

29 29 "Supply of STP (Shielded Twisted Pair) CAT-6 cable shall Boxes 10.00 5801.00 58010.00

be compliant with latest EIA/TIA- 568-B.2-1 standard or

latest (1 Box = 305 Mtrs) Make- D-Link/Digisol or

superior. Inspection:Consignee"

SEALDAH DIVISION-S AND T/EASTERN RLY

30 30 Supply of power cable 3 core 2.5 sq mm multi strand Metre 4100.00 51.69 211929.00

(50/0.25 mm dia) cable as per IS 694:1990 reaffirmed

1995 or latest suitable for railway electrification area.

Make: Havells/Polycab/Mescab or superior. Inspection :

31 31 "Supply of 2 core screened/shielded multistrand PVC Metre 3500.00 29.66 103810.00

insulated wire (24/0.2 mm dia) for speaker load line.

Make: Havells/Polycab/Mescab or superior. Inspection :

32 32 Laying of Power Cable/STP/UTP CAT-6/Switch Board Metre 16000.00 16.10 257600.00

Cable/speaker cable/Earth Cable etc. through flexible

PVC Conduit Pipe/ GI Pipe/HDPE Pipe (where necessary)

as per direction of the Rly. Representative. Note-This

also includes Laying of STP/UTP CAT-6 from Relay

room/OFC to SM Panel room for Block circuits as per the

site/station, Earth cable as instruction of railway

representative & Laying of Power cable for VSS locations

or any as per instruction. Cable will be supplied by

33 33 "Supply PVC conduit pipe of size 50 mm dia. Min 3 mm Metre 50.00 65.25 3262.50

thickness with ISI mark, Make: Supreme/Polycab/Jindal

or Superior. Inspection : Consignee"

34 34 "Supply of conduit pipe size 25 mm dia min. 2 mm Metre 15050.00 24.80 373240.00

thickness with ISI mark. Make: Supreme/Polycab/Jindal

or Superior. Inspection : Consignee."

35 35 Fixing of PVC conduit pipe on wall, bridges, platform Metre 15000.00 5.27 79050.00

shed complete with 'U' clamps and necessary fixture

screws etc. as per route given by site engineer of

Railways. Note- PVC pipe will be supplied by railway.

36 36 "Supply of rolled flexible PVC Pipe of 25 mm dia. Metre 300.00 24.25 7275.00

Inspection: Consignee"

37 37 Supply & installation of G.I. Perforated Type Cable Tray Metre 150.00 629.62 94443.00

with all accessories like Tees, elbow, reducers, couplers

etc. Cable Tray Sheet Thickness: 2.5 mm, Cable Tray

Width: 300mm, Cable Tray Height (mm): 50 as per Drg

No. SK/SDAH 2025/01 dated:25.07.2025 or latest

Inspection: Consignee

38 38 Supply of 40 mm dia permanently lubricated HDPE Kilometre 9.20 53277.12 490149.50

telecom: ducts (with chord) as per RDSO SPEC.NO.

RDSO/SPN/TC/45/2013 REVISION 2.0 with latest

amendments or Latest in length of 1000 mtrs/roll For

each km. Of HDPE duct following items are to be

supplied (a) end plugs-2 nos. (b) cable sealing plugs - 2

nos. (c) plastic couplers slip fit/push fit type-2 nos. (d)

end plugs to be provided along with drum 2 nos. (Note:

The color of duct will be as per Technical circular -124.

For station area the color of HDPE duct will be brown.

The colour of the duct is to be confirmed by the in-

charge of the work before supply) Inspection: Consignee

39 39 Laying of HDPE pipe duct, 40/33 mm in trenches Kilometre 9.00 20961.02 188649.18

/overhead and protective works including pulling of

mono-mode armoured OFC cable through duct in

trenches and as advised by site engineer. Note:- (1) the

contractor will take over the OFC cable from railway

store to site of work duly checked the continuity of each

fibre from end to end . (2) before & after laying of optical

fibre cable through duct, continuity test from end to end

of each fibre to be made by the contractor to ensure

availability of all duly certified by the site engineer.

Note: OFC & HDPE Duct will be provided by railway.

40 40 Over head laying of 6-core OFC cable along with Metre 200.00 35.37 7074.00

FOB/Wall/shed structure etc. including clamping/fixing

the PVC conduit over wall ceiling/open

space/terrace/existing fixtures etc. as per directives of

Rly. Site engineer.

SEALDAH DIVISION-S AND T/EASTERN RLY

41 41 Earthwork in filling in embankment, guide bunds, around cum 10.00 124.58 1245.80

buried type abutments, bridge gaps, trolley refuges, rain

bunds if provided, platforms etc. with earth excavated

from outside railway boundary entirely arranged by the

contractor at his own cost as per RDSO's latest

guidelines and specifications and special condition of

contract including all leads, royalty, lifts, ascents,

descents, crossing of nallahs or any other obstructions.

The rates shall include all dressing of bank to final

profile, demarcation and setting out of profile, site

clearance, removing of shrubs, roots of vegetations

growth, heavy grass, benching of existing slope of old

bank, all handling/re-handling. Taxes, Octroi and royalty

etc. as a complete job. Cut trees shall be property of

railways and to be deposited in the railway godown

unless specified otherwise in the Special conditions of

42 42 Repair of pucca roads to original state in level/ Road Metre 100.00 216.95 21695.00

crossing area after cable laying. All required material for

repairing will be arranged by firm by their own cost

43 43 "Supply of Double Walled Corrugated (DWC) HDPE Numbers 5.00 576.27 2881.35

Pipe/duct with associated collars etc. as per RDSO

Specification No. RDSO/SPN/204/2011 ver 1.1 or latest

with latest ammendments anti-rodent & anti-oxidant and

non-flame propagating type in 6 meters straight length

and of size 120 mm outer dia& 103.5 mm inner dia. (The

manufacturers, suppliers must produce valid IS license

and should be certified under ISO 9000 and shall submit

copy of certificate). One of the following coupling

arrangements should also be supplied with each pipe as

per the site requirement. 1) Suitable snap fit coupler

with rubber O-Ring 2)Spacers, 3)Tees, 4)Bend, 5)End-cap

(The total quantity of above items is equal to no. of pipes

supplied.) DWC pipe shall be marked at every 1 mtr.

length in such a way that manufacturer's name, vendor

name and year of manufacture can be easily identified.

Inspection: Consignee "

44 44 Placing of DWC HDPE/RCC/GI pipes along with collars in RMT 30.00 26.27 788.10

trenches at places near track and road, crossings,

platform cuttings etc.

45 45 Cement concrete work for miscellaneous items in the cum 50.00 3047.46 152373.00

ratio 1: 3: 6. Item includes excavation, ramming, curing

and plastering with cement & sand mixture (aggregate

not exceeding 3.8 cm.) (Aggregate cement & sand to be

supplied by the contractor). Wherever depth of 0.5 m

cable trench is not feasible, cable shall be protected as

:- Preparation of cement mixture 1:3:6 with contractor's

own materials and spreading cement concrete mixture

layer of 100 mm thick over the already laid cables in the

excavated trench.

46 46 Supply and installation of Telecom Console Numbers 1.00 50000.00 50000.00

Unit/Customized rack for installation of all telecom

equipment, telecom cable and telecom power supply in

one unit/customized rack consisting of front and back

panel as per Technical policy circular-113. (Note: The

console unit should be made of CRCA steel sheet with

ivory colour powder coated finish and should have

locking and sealing arrangement. The dimension of

console unit is to be supplied as per the site

requirement) Inspection: Consignee

SEALDAH DIVISION-S AND T/EASTERN RLY

47 47 "Supply of basic material to construct unit maintenance Lot 8.00 12836.44 102691.52

free earth as per RDSO Specs. No RDSO/SPN/197 Ver.1.0

or latest and conforming to RDSO Drg. No. SDO / RDSO/

E&B/001 or Latest. and RDSO Doc. No. RDSO-SIG0SPD

STS/E/TAN/3006 ver 3.1 or latest. Necessary testing

certificate of UL, IEC to be produced. It consist of

following: (a) Copper bonded steel electrode of 3.0 m

long, 17.2 mm dia with copper bonding thickness of

minimum macrons and UL listed and marked = 1 no. (b)

Earth enhancement material supplied in sealed bags of

minimum 10 kg = 3 nos. (c) Copper strip of 200x25x6

mm, to terminate earth rod = 1 no. (d) Copper strip of

300x25x6 mm (MEEB) = 1 no. (e) Copper strip of

150x25x6mm (SEEB) = 1 no. (ii) Supply of 35 sq. mm

multi strand single core PVC insulated copper cable as

per IS: 694 for connecting main earth electrode to MEEB

in the equipment room (4nos.) (minimum 10 meter and

as per site requirement) (iii) Supply of 16 sq. mm multi

strand single core PVC insulated copper cable as per IS:

694 for connecting MEEB to SEEB and SPD to MEEB

(minimum 10 meter) (iv) Supply of 10 sq. mm multi

strand single core PVC insulated copper cable as per IS:

694 for connecting various equipment to SEEB (v)

Supply of copper lug sleeve for 3/16 cable Inspection:

48 48 "Installation of Unit Maintenance Free Earth as supplied Set 8.00 5575.42 44603.36

in above item. It includes ( i ) Digging the earth to the

required depth.(ii) Insertion of electrode. (iii) Filling of

earth enhancing compound (Approx.30 Kg)(iv) Provision

of exothermic weld connections to copper tape of 25

mm x 6 mm x 200 mm to the earth electrodes. All

material tools and features requiredfor weld will be

arranged by contractor. (v) This also includes CC cover

1.5 ft x 1.5 ft. 1 ft wall thickness 2 inch with cover 3-inch

thickness. Cables 35 Sq mm/ 16 Sq mm/10sqmm

forconnecting earth to busbar, busbar to busbar and bus

bars to various equipment. Earth electrode of 17.20 mm

dia and 3.00 meter long high tensile low carbon steel

circular rods molecularly bonded with copper and outer

surface (minimum copper bonding thickness of 250

microns to made requirement of under writer's

laboratories (UL) 467-2007 or latest. Copper strips of

200 mm x 25 mm x 6 mm to be welded with each earth

electrode, copper strips of 300 mm x 25 mm x 6 mm for

main equip- potential bus bar, copper strips of 150 mm

x 25 mm x 6 mm sub equip-potential bus bar in relay

room, power room, OFC room and panel room. The

distance between the MEEB and the SPD box should not

be more than 0.5 mtrs. Inspection chamber of site 300

mm x 300 mm x 300 mm (Inside dimension) of

approximate 50 mm thick with pulling hooks to cover the

earth pits. Note: The installation of this item shall be

carried out as per RDSO Specs. No RDSO/SPN/197

Ver.1.0 or latest and conforming to RDSO Drg. No. SDO /

RDSO/ E&B/001 or Latest. and RDSO Doc. No. RDSO-

SIG0SPD (PROJ)/1/2020 dated 01.01.2025 or latest.

STS/E/TAN/3006 ver 3.1 or latest "

49 49 "Supply of optic fiber splice closure (24 fiber) as per tec. Numbers 35.00 3015.25 105533.75

Specification no. TEC/GR/TX/OJC-002/03/APR-2010 or

latest with latest amendment including all miscellaneous

items and consumables for fiber splicing. Inspection:

50 50 Jointing, terminating & splicing of 24 fibre optic fibre Numbers 37.00 9004.24 333156.88

cable and fixing of termination box/FDF/placing of joint

closures in the pit required at various locations including

transportation of all the jointing & terminating materials

from railway store to the work site and returning leftover

materials to the railway store. Note:Jointing/Splicing of

Cables/OFC for permanent restoration of cables/OFCs at

any time wherever instructed. Note-Splice closure will

be provided by railway.

SEALDAH DIVISION-S AND T/EASTERN RLY

51 51 Excavation of OFC pit for OFC cable jointing of size 1.5m Numbers 35.00 5655.93 197957.55

x 1.5m x 1.2 m or as per site requirement for all type of

soils. Back filling the pit and ramming after jointing.

Provision of brick walling the four walls and bottom of pit

with RCC slab, with bottom & top cover with holes for

drainage and cable entry with filling of dry sand mixed

with anti-termite chemical up to 400mm height. Note: All

the materials including cement,Bricks, sand etc.

required for the above will be supplied by the tenderer.

52 52 Supply & Execution/Installation of 20 pair CT Box with 40 Numbers 80.00 1713.81 137104.80

Nos (1 in 1 out) Wago Terminal properly fixed on carrier

rails with end plates and end stopper inside the CT box

for termination of PIJF/Quad cable .Note- As per

Technical policy circular no. 110, the twisting of

Quad/PIJF cables to be done before termination at

location boxes/CT rack/OFC room/SM Room/CT boxes.

Soldering/Tinkering of armour earthing to be done.

Inspection : Consignee

53 53 "Supply of Fiber Distribution Management System 24 Numbers 12.00 7826.00 93912.00

port, Single Mode, Simplex Fiber Optic Patch Panels,19

inch 1 U Rack Mountable with SC connector with all

accessories. Make: Syrotech/Commscope/Digisol or

superior Inspection: Consignee."

54 54 "Supply of Fiber Distribution Management System 12 Numbers 6.00 7011.19 42067.14

port, Single Mode, Simplex Fiber Optic Patch Panels, 19

inch 1 U Rack Mountable with SC connector with all

accessories. Make: Syrotech/Commscope/Digisol or

superior Inspection: Consignee. "

55 55 Installation of LIU/FDMS and termination as per site Numbers 16.00 298.53 4776.48

56 56 Splicing /Dropping/Termination of each Fiber /Pigtail in CORE 400.00 44.83 17932.00

the LIU/FDMS through fusion Splicing of the termination

of OFC Cables, as per the instructions of Railway site

57 57 Testing of all fibres o f t h e optic fibre cable, quad, PIJF Station 1.00 9036.44 9036.44

cable, ADMS, mux and other accessories installed above

and final commissioning of optic fibre communication link

conforming t o railway's specification including e n d to

end testing for realisation of optic fibre system.

58 58 Supply, installation and complete indoor wiring of 19 Numbers 1.00 31838.98 31838.98

inch (42U) covered Rack of size 2035 mm x 600 mm x

600 mm (Approx.)(a).Size of Server Rack Enclosure :

42U (b) Type of Server Racks : Rack Enclosures.(c) Rack

Size(mm) : 2035 mm x 600 mm x 600 mm (Approx.). (d)

Mount Type : Floor mount (e) Front glass Door : Yes. (f)

Secure Locks : Available (g) Support cable entry from top

or bottom : Yes (h) Vertical & Horizontal managers : Yes

(i) Numbers of Rack trays : 2 (j) Number of Fan For Heat

dissipation (nos) : 4 (k) Number of fan trays : 4 (l) PDU

Power Strips : 1 with 6 Sockets. The rack shall be

complete with all fittings for housing SDH equipments,

Primary MUX, DDF, MDF using krone modules and other

required accessories. Make: HCL/VALRACK or superior,

Inspection: Consignee

59 59 "Supply of wall mount 9U Rack Enclosures Numbers 12.00 7239.02 86868.24

Networking/Server Rack with power strip 5A socket 06

no. & 01 MCB, Depth of the Rack: Upto 500

mm,Transparent Toughened Glass used in front door,

CRCA Steel rear door with Secure Locks,Cable Manager,

Support cable entry from top or bottom, with fan tray

and two nos. fans. Make: Valrack/Netrack/Dynamic/D-

Link or similar Inspection: Consignee. "

60 60 "Supply of 6U wall mounted rack with power strip 5A Numbers 10.00 3605.85 36058.50

socket 06 no. & MCB, Depth of the Rack: Upto 400mm,

Transparent Toughened Glass used in front door, CRCA

Steel rear door, with Secure Locks, Support cable entry

from top or bottom, with fan tray and min. 02 nos. fans.

Make: Valrack/Netrack/Dynamic/D-Link or similar.

Inspection: Consignee. "

SEALDAH DIVISION-S AND T/EASTERN RLY

61 61 "Supply of wall mount 4U Rack with power strip 5A Numbers 10.00 3919.60 39196.00

socket 06 no. & MCB, Depth of the Rack: Upto 400mm,

Transparent Toughened Glass used in front door, CRCA

Steel rear door, with Secure Locks, Support cable entry

from top or bottom, with fan tray and min. 01 nos. fans.

Make:Valrack/Netrack/Dynamic/D-Link or similar.

Inspection: Consignee. "

62 62 Installation of 9U/6U/4U rack with necessary angles, Numbers 32.00 469.54 15025.28

fasteners and other fixing arrangements.

63 63 "Supply,Installation & Commissioning of Telecom TDM Pair 8.00 53344.50 426756.00

Multiplexer Rack Mountable Device consisting of one E1

port, Two V.21 /V.23 (E&M) 2W/4W interfaces with auto

change over mechanism to Quad ports 2W/4W ; each

port configurable as 2W or 4W no restriction in

configuration ; Automatic change over of the data traffic

between two axle counters if the E1 Link between the

Axle counter fails then will switch over to the copper

automatically. If the Power to the Converter Fails then It

also Automatically changes the data transportation over

the copper link.Potential Free contacts for indicating the

events E1 Link UP, E1 Link DOWN, V.21 Signal UP and

DOWN between two axle counters. 48 VDC power

s u p p l y. Make/Brand:TEAMLINK FABIO-1CX/MRO-TEK-

MAPLE or similar. Inspection: Consignee"

64 64 "Excavation of cable trench as per cable route plan, 1.2 cum 1800.00 207.63 373734.00

Mtr. deep and of 0.3 Mtr. wide at bottom without brick

as per DRG. NO. S&T/C-40(NKG), SK/4/95/NKG,

SK/8/95/NKG. or latest alongside the track in all kinds of

soil, conforming to distances as per cable route plan and

refilling. This work includes clearing of route from

bushes etc. The work shall be done as per the extant

practice on Eastern Railway and instructions of Railway

Engineer at site. Note:-(a)for all trenches from distant

signal to home signal and to relay room, the minimum

headway above the uppermost cable in the trench

should be 600mm. If due to a large no. Of cables

headway is not available, 4"" of 1:2:4 concreting should

be done. Note:-(b-1) payment will be made as per actual

work done on pro-rata basis, if required depth is not

available at site. (b-2) if the depth of trench is not

uniform in a span of 100 mtr. Or shorter lengths if site

condition demands along the cable run, minimum depth

will be taken for that particular stretch for payment. "

65 65 "Supply of Armoured Duplex Fiber Optic Patch Cord 3 Numbers 150.00 1271.19 190678.50

meters (LC-SC/SC-SC/LC-LC/FC-LC) as per site

requirement.Outer Jacket: PVC or LSZH, Mode:Single,

Durability: 1000mate/demate cycles, Nominal

Wavelength : 1310 nm, Fibre Attenuation: < 0.38 dB/Km

at 1310nm, < 0.25 dB/Km at 1550 nm, Insert

Loss/connector: Maximum 0.1dB per connector plus fibre

loss,Return loss : Better than 45dB Make:

Iveonet/Relemac or superior Inspection: Consignee"

66 66 Supply of Universal 2/4 wire way side DTMF control Numbers 38.00 4409.32 167554.16

telephone as per RDSO spec. no. IRS: TC:82: 2005 (with

Amdt. 3) or latest. Make-Bentron/ EPSILON or similar.

Inspection: Consignee

67 67 "Supply of power supply unit for telecom installation at Numbers 45.00 3169.49 142627.05

way side station suitable to operate max 6 equipments

of DTMF type (12V/7AH) battery with suitable battery

charger) as per RDSO spec. No. IRS: TC-72-97 or latest.

Make-Bentron/ EPSILON or similar Inspection:

68 68 Supply of 4W way station DTMF equipment as per RDSO Numbers 33.00 5686.44 187652.52

spec. no IRS : TC : 60 /2007 (DECODER) or latest.Make-

Bentron/ EPSILON or similar. Inspection: Consignee

69 69 Installation of 4W way station DTMF equipment & 4 wire Numbers 5.00 1065.25 5326.25

telephone.Required fixing arrangements to be done by

SEALDAH DIVISION-S AND T/EASTERN RLY

70 70 Supply of standard 19"rack mountable , -48V DC Numbers 1.00 168837.29 168837.29

working, Add-Drop STM-4 SDH equipment conforming to

GR No. TEC/GR/TX/SDH - 010/03.Jan 2011 or latest

amendment, complete with redundant power supply, 2

no. STM 4 of aggregate L.4.2 Optical interface

modules/Cards one each for East and west side, TX/RX

and 2 nos. of STM-1 S 1.1 optical interface modules

complete with 5 mtrs long optical fibre cords, 21 E1s

with DDFs and cable assembly for termination to DDF

and minimum 8 nos. of 10/100 Base-T Ethernet ports,

Fast Ethernet on SDH [EoS] 10/100 Base-I interface

module/card supporting with LCAS and GEP, order wire

subrack DDF installation material, manuals and other

accessories. Complete Engineering order wire (EOW)

arrangement. Necessary/Firmware for local/remote

monitoring/configuration of the equipment through EMS

and Software/Firmware interface to work all Network

elements as Gateway Network Element [GNE], 2 nos of

MCBs of appropriate rating and necessary connecting

cords and cables for power supply modules. Inspection:

71 71 Installation and commissioning of STM-4 in the existing Numbers 1.00 19911.02 19911.02

rack with ready infrastructure or in new rack as desired

by the site Engineer.

72 72 "Supply of 2 MB Programmable Primary Digital drop Numbers 5.00 126532.20 632661.00

insert multiplexer as per RDSO Specs. IRS:TC: 68-2012

Amdt. 1 or latest with conference facility and other

stipulation to tender documents and fully wired for 30

channel complete with power supply card, remote

control, supervision facility and all other accessories,

installation material, manuals etc. It should have

facilities to accommodate data interface card in multi

drop mode and should be able to support cards needed

for video conferencing and ISDN. It shall support NMS

installed at Test Room and may operate local/remote

location of entire section. It also includes submission of

all technical documents, manuals and supply of all

miscellaneous items which will be required for final

testing and commissioning of system. The above MUX

should be equipped with following circuits: -i) 2 wire/ 4

wire E&M VF circuits ( minimum 16 nos ckts)ii)

Subscriber loop circuits ( minimum 4 nos ckts iii)

Exchange loop interface circuits (minimum 8 circuits ) iv)

This also includes connecting all pigtails, optical patch

cords etc. to the SDH equipments. This also includes

connection of SDH and primary MUX equipment with all

interface cards to the 48V Bus including supply of wires

and connectors termination of all evens on DDF taking

PVC cable over runway or a wall and termination of VF

interface circuit to the Krone type. Inspection: RITES"

SEALDAH DIVISION-S AND T/EASTERN RLY

73 73 Installation, wiring, testing and commissioning of 2 MB Numbers 2.00 9637.29 19274.58

Programmable Primary Digital drop insert multiplexer as

per RDSO Specs. IRS:TC: 68-2012 Amdt. 1 or latest with

conference facility and fully wired for 30 channel

complete with power supply card, remote control,

supervision facility and all other accessories, installation

material, manuals etc. It should have facilities to

accommodate data interface card in multi drop mode

and should be able to support cards needed for video

conferencing and ISDN. It shall support NMS installed at

test Room and may operate local/remote location of

entire section. It also includes submission of all technical

documents, manuals and supply of all miscellaneous

items which will be required for final testing and

commissioning of system.The above MUX should be

equipped with following circuits: -i) 2 wire/ 4 wire E&M VF

circuits ( minimum 16 nosckts)ii) Subscriber loop circuits

( minimum 4 nosckts)iii) Exchange loop interface circuits

(minimum 8 circuits )iv) This also includes connecting all

pigtails, optical patch cords etc to the SDH equipments.

This also includes connection of SDH and primary MUX

equipment with all interface cards to the 48V Bus

including supply of wires and connectors termination of

all evens on DDF taking PVC cable over runway or a wall

and termination of VF interface circuit to the Krone type.

All materials such as wires for Earthing & power supply,

wire carrying aluminium

ladder,MCB,Connectors,foundation bolts,nuts,base

frame,mounting accessories for fitting of

transformers,U-Link Panels,inter connecting cables etc.

required for the above shall be supplied by the

74 74 Supply of Subscribe loop interface cards, minimum 4 Numbers 14.00 10383.05 145362.70

circuits per card as per RDSO Specs. IRS:TC: 68-2012

Amdt. 1 or latest for existing WEBFIL PD MUX. Inspection

75 75 Supply of 2W/4W E&M interface cards, minimum 4 Numbers 14.00 10189.83 142657.62

circuits per card as per RDSO Specs. IRS:TC: 68-2012

Amdt. 1 or latest for existing WEBFIL PD MUX. Inspection

76 76 Supply of Exchange loop interface card, 4 circuits per Numbers 8.00 6907.63 55261.04

card as per RDSO Specs. IRS:TC: 68-2012 Amdt. 1 or

latest. for existing WEBFIL PD MUX Inspection :

77 77 Supply of surge suppressor for all the 30 circuits derived Numbers 4.00 5554.24 22216.96

from the Primary MUX (Z protection). (Note: The unit

(no.) denotes a set of surge suppressor required for all

the 30 circuits derived from primary MUX) Inspection:

78 78 Supply of 8/6 port (100/10 base T) ethernet interface Numbers 1.00 43120.40 43120.40

card for SDH ADM STM-4 suitable for STM-4 (Model-TJ

1400). Inspection : Consignee

79 79 Supply of NIM card as per RDSO spec no. IRS-TC-68/2012 Numbers 14.00 22595.60 316338.40

or latest and suitable for existing WEBFIL PD MUX.

Inspection : Consignee

80 80 Supply of Tributary module card as per RDSO spec no. Numbers 14.00 34369.56 481173.84

IRS-TC-68/2012 or latest and as per suitable for existing

WEBFIL PD MUX. Inspection : Consignee

81 81 "Supply and installation Of 32U(600X600mm) Floor Numbers 4.00 28500.00 114000.00

Mount Network Rack with PDU of 6 Socket (15/5 amp

socket), Server Tray (3 Nos), Cable Organiser 1U Closed,

4 Fan with all required accessories. Make:

Valrack/Netrack/Dynamic/D-Link or superior. Inspection:

82 82 "Supply of Magneto telephone, desk type as per spec. No Numbers 24.00 2935.35 70448.40

IRS/TC-79/2000 Amdt. 4 or latest with all accessories

Make: Epsilon/Anu Vidyut or superior. Inspection:

83 83 "Supply of 8 lines annunciator for Magneto Phones. Numbers 4.00 7184.74 28738.96

Make- EPSILON or superior. Inspection- Consignee"

SEALDAH DIVISION-S AND T/EASTERN RLY

84 84 "Supply of Master telephone with voice recording facility Numbers 5.00 42348.00 211740.00

of Electronic LC gate telephone systems with voice

recorder as per RDSO SPEC.NO.RDSO/SPN/TC/51-2021

REV 1.0 or latest. Material to be supplied from RDSO's

approved source only with 03(three) years full

warranty.Note: - 1) The date of manufacture of the item

should be of current year at the time of supply to railway

stores. Inspection: RDSO"

85 85 "Supply of Gate (slave) telephone as per RDSO Numbers 10.00 4415.00 44150.00

SPEC.NO.RDSO/SPN/TC/51-2021 REV 1.0 or latest

Material to be supplied from RDSO's approved source

only with 03(three) years full warranty. Note: - 1) The

date of manufacture of the item should be of current

year at the time of supply to railway stores. Inspection:

86 86 "Supply of 24V Power supply unit with MF Battery and Numbers 10.00 5706.00 57060.00

Charger for Master Telephone As per RDSO

SPEC.NO.RDSO/SPN/TC/51/2021 REV 1.0. or latest. Note:

PSU should have another output of 12 V + 0.5 V, with

current capacity of minimum 500 mA for local use of

Station Telephone Unit. Inspection : RDSO "

87 87 Supply of cylindrical type V.F. transformer Numbers 54.00 620.34 33498.36

1120:600/470:1120 as per IRS/TC/76-2021 ver. 01 or

latest. Note: The transformers (1120:600/470:1120) to

be supplied as per the site requirement. Inspection -

88 88 Installation of V.F. Transformer 1120:600/470:1120 to Numbers 4.00 380.20 1520.80

the site given by the railway representative.

89 89 "Supply, Fixing and wiring of 20 Pairs Krone type D.P. Numbers 4.00 1007.72 4030.88

Box with krone Module, the box should be Powder

Coated Material - Metal (MS). Inspection: Consignee"

90 90 Supply of SMPS based Battery Chargers as per RDSO Numbers 1.00 78583.05 78583.05

Spec for Telecom use 48 volts, 25 Amps in 2+1

configuration modules of 25 Amps with ultimate

expandable capacity 50 Amps, automatic switching

between the modules as per RDSO Spec No.

RDSO/SPN/TL/23/1999 version 4 or latest along with two

potential free contacts. Make- Statcom/Amara Raja or

superior. Inspection: RDSO

91 91 Installation of Battery chargers, Power distribution Board Numbers 1.00 3879.66 3879.66

along with MCBs of suitable ratings and wiring and

commissioning of External alarm contacts through NMS

& earthing of SMPS based Chargers to nearest

SEEB(10sqmm earth cable green color will be provided

by contractor). The work includes supply of MCBs, lugs

and other accessories required for installation of power

plant. Inspection: Consignee

92 92 Supply of 48Volt/200AH maintenance free VRLA Numbers 1.00 75756.77 75756.77

Batteries duly charged as per IRS Spec. No. S-93/96(A)

with amendments-1 or latest. Inspection: RDSO

93 93 Installation, wiring, testing & commissioning of Numbers 1.00 16328.81 16328.81

48Volt/200AH maintenance free VRLA Batteries duly

charged as per IRS Spec. No. S-93/96(A) with

amendments-1 or latest.The work includes supply of

battery rack, min. 20Mtr of 16sq.mm power cable with

lugs for connecting load & battery through the charger,

battery lugs and other accessories required for

installation of power plant. Make: Amara Raja/Exide or

superior. Inspection: Consignee

94 94 "Supply of RR Cell, 1.5V/45 AH. Make: Spark/Tiger or Numbers 50.00 624.70 31235.00

superior. Inspection: Consignee."

95 95 "Supply of 12V,10A SMPS Based power supply unit Numbers 20.00 6212.03 124240.60

suitable for 25W VHF set. Make-Axiom/Bentron or

superior. Inspection: Consignee."

96 96 "Supply of MCB 16A, Double Pole,DIN Rail Mount. Numbers 50.00 343.30 17165.00

Make:Havellls/Schneider or superior. Inspection:

97 97 "Supply & installation of 12 Volt, 120 AH single unit MF Numbers 2.00 12500.00 25000.00

battery for 25W VHF set. Make- Exide/Amaron/Quanta or

superior Inspection : Consignee"

SEALDAH DIVISION-S AND T/EASTERN RLY

98 98 Supply & Installation of DC-DC converter for emergency Numbers 2.00 17577.97 35155.94

communication through V.H.F. as per specification - the

DC DC converter shall be independent for each vhf base

equipment (voice equipment) and shall allow t o work

from -48V nominal input (-48V to -60V variation) & output

12V DC. The power capacity to deliver 10A current with

output short circuit protection & ripple voltage less than

5mv for telecom circuit. Short circuit current not more

than 2 mA, input-output insulation by 2.5 KV, load &

output regulation +/-1% with ERTL certification.

Make:VERON/DACS/Machronics or superior. Inspection:

99 99 Supply of Buffer amplifier for emergency communication Numbers 2.00 11726.27 23452.54

through V.H.F. As per voice frequency channel shall be

6 0 0 ohms balanced 4 W (viz. 2 W f o r transmit, 2 W for

receive) and 2W for E&M signalling. The nominal voice

frequency signal shall be 0 dbm level the buffer amplifier

should work of -48V DC or can from the DC-DC converter.

B u r n i n o f t h e complete equipment a t 5 5 degree

centigrade to avoid infancy failures. During the test the

equipment shall be kept continuously on.

Make:VERON/DACS or superior. Inspection : Consignee.

100 100 "Supply of Floor mounting surge supressure(4 Nos. Of Numbers 1.00 9552.19 9552.19

16A Socket in each strip), protection should be provided

in each socket separately, Weather proof light gray color

M.S. enclosure, Normal input voltage:230VAC,+/- 10%

Single phase, 50-60 Hz, Input AC cord: 6 ft. 3 core 15

amps. One ANCHOR/Havells make 16 amps top to be

provided at one end of the mains cord, LED indication:

One 5mm red LED for power ON, One 5mm green LED

for protection present., Output Termination: 4 Nos.16

amps socket of anchor make to be provided, Thermal

cutoff: 16 amps MCB to be provided, make: Rockware or

Superior, Inspection: Consignee."

101 101 Supply, Fixing and wiring of 10 Pairs Krone type D.P. Box Numbers 6.00 685.59 4113.54

with krone Module, the box should be Powder Coated

Material - Metal (MS). Inspection: Consignee

102 102 Supply of UTP CAT-6 cable as per EIA/TIA- 568-B.2-1 Metre 915.00 16.10 14731.50

Make: D Link/Molex/Comscope or superior. Inspection:

103 103 "Supply of MCB 10A, single Pole, DIN Rail Numbers 30.00 106.26 3187.80

Mount.Make:Havellls/Schneider or superior Inspection:

104 104 "Supply of MCB 06A, Double Pole, DIN Rail Mount. Numbers 10.00 310.60 3106.00

Make:Havellls/Schneider or superior Inspection:

105 105 "Supply of Small Form- Factor Pluggable (SFP) as per Pair 29.00 9806.10 284376.90

IEEE standard: IEEE 802.3z,Connector type: LC

type,Wavelength(nm): 1310 nm, Fibre type: Single

mode, Max cable distance: upto 20 km.To be suitable for

Datacom equipment/ STM-1 & STM-4 supplied as per site

requirement. Make:DIGISOL/Netgear/Cisco or superior

(to be suppied in pair) Inspection: Consignee."

106 106 "Supply of 250 watt Amplifier Make Ahuja/NEXA or Numbers 16.00 9239.83 147837.28

superior Note: The supplied amplifiers should have USB

support. Inspection: Consignee"

107 107 "Supply of 500 watt Amplifier Make Ahuja/NEXA or Numbers 7.00 22487.29 157411.03

superior Note: The supplied amplifiers should have USB

support. Inspection: Consignee."

108 108 "Supply of 700 watt Amplifier Make Ahuja/NEXA or Numbers 2.00 25583.90 51167.80

superior. Note: The supplied amplifiers should have USB

support. Inspection : Consignee"

109 109 "Supply of 40 W high fidelity PA horn speaker IP-65 rated Numbers 50.00 5180.51 259025.50

including fixtures, Custom mounting bracket and other

material required. Make- Ahuja/BOSCH or superior.

Inspection: Consignee."

110 110 "Supply of 15 watts Horn speaker with 10 watt tapping, Numbers 30.00 1611.02 48330.60

matching transformer and driver unit including fixtures ,

Custom mounting bracket and other material required.

Make- Ahuja/BOSCH/Bose or superior Inspection:

SEALDAH DIVISION-S AND T/EASTERN RLY

111 111 "Supply of column speaker 15W with LMT all metal Numbers 26.00 1294.91 33667.66

weather resistant, including fixtures,Custom mounting

b r a c k e t and other material required. Make-

Ahuja/Bosch/Bose or superior Inspection:Consignee. "

112 112 "Supply of Dynamic Microphone with cord & stand. Numbers 42.00 1426.72 59922.24

Make: Ahuja/Shure/Sennheiser or superior. Inspection:

113 113 "Supply of Microphone Signal Cable : 0.75 Sq. Mm two Numbers 5.00 4900.00 24500.00

core shielded microphone cable. 100 m roll. (1 Roll=1

No.) Inspection : Consignee"

114 114 Supply, Installation, testing and Commissioning of Numbers 10.00 39271.19 392711.90

Platform dual face, 4 digit, GPS synchronised digital

clock as per RDSO spec. RDSO / SPN/ TC /62 /2008 Rev.

4.1or latest with latest ammendments, with LED of

Blue/Red/White colour and size approximately 762 x 381

x 228 mm It also includes all fitting arrangements.

(Colour to be decided by Railways).Inspection: (i)

RDSO/RITES if value of item in work more than 5 lakhs or

as per extant policy.(ii) Consignee subject to

procurement from RDSO approved vendors if value of

whole item in work less than 5 lakhs or as per extant

115 115 "Supply of Digital Clock suitable for Office Complex with Numbers 20.00 11199.15 223983.00

GPS Synchronization in standalone mode as per Clause 6

of RDSO spec. RDSO / SPN /TC /62 /2008 Rev. 4.1 or

l a t e s t It also includes all fitting arrangements.

Inspection: Consignee"

116 116 "Supply of 1 x 6 Sq.mm. (Green) multi strand copper Metre 700.00 35.59 24913.00

power wire as per IS: 694:2010 orlatest, 84 conductor

each dia 0.30mm +/- 0.01 with insulation thickness of

0.8 mm and nominal conductor resistance of 3.3

ohms/km and test parameters as per RDSO

Specn.No.IRS:S- 76/89 (Amnd.3) or latest. Color of the

wire which is required will be specified by the Engineer

in-charge Inspection: Consignee"

117 117 "Supply of 1 x 10Sq.mm. (Green) multi strand copper Metre 700.00 100.85 70595.00

power wire as per IS: 694:2010 or latest, 140 conductor

each dia 0.30mm +/- 0.01 with insulation thickness of

1.0 mm and nominal conductor resistance of 1.91

ohms/km and test parameters as per RDSO

Specn.No.IRS:S- 76/89 (Amnd.3) or latest. Color of the

wire which is required will be specified by the Engineer

in-charge Inspection: Consignee"

118 118 "Supply of 1 x 16 Sq.mm. (Green) multi strand copper Metre 700.00 111.02 77714.00

power wire as per IS:694:2010 or latest, 126 conductor

each dia 0.40mm +/- 0.01 with insulation thickness of

1.0 mm and nominal conductor resistance of 1.21

ohms/km and test parameters as per RDSO

Specn.No.IRS:S-76/89(Amnd.3) or latest.Colour of the

wire which is required will be specified by the Engineer

incharge. Inspection: Consignee"

119 119 "Supply of 1 x 35 Sq.mm. (Green) multi strand copper Metre 600.00 150.00 90000.00

power wire as per IS:694:2010 or latest, 276 conductor

each dia 0.40mm +/- 0.01 with insulation thickness of

1.2 mm and nominal conductor resistance of 0.554

ohms/km and test parameters as per RDSO

Specn.No.IRS:S-76/89(Amnd.3) or latest.Colour of the

wire which is required will be specified by the Engineer

incharge. Inspection: Consignee"

120 120 "Supply of Tinned Copper LUGs for fitting in Cable Size: Numbers 1500.00 2.54 3810.00

6 sqmm, Barrel Inner-dia: 4.0mm, Barrel Outter-Dia:

5.5mm, Barrel Length: 10mm, Stud Hole Center-dia:

8.2mm, Palm Width: 10.0mm, Thickness: 1.3-1.5mm,

Lug Length: 24mm,Thimble type: Ring/Fork type as per

site requirement. Inspection: Consignee"

121 121 "Supply of Tinned Copper LUGs for fitting Cable Size: Numbers 1500.00 3.39 5085.00

10sqmm, Barrel Inner-dia: 4.7mm, Barrel Outter-Dia:

7.10mm, Barrel Length: 10mm, Stud Hole Center-dia:

9.9mm, Palm Width: 12.6mm, Thickness: 1.8, Lug

Length: 27mm, Thimble type: Ring/Fork type as per site

requirement. Inspection: Consignee"

SEALDAH DIVISION-S AND T/EASTERN RLY

122 122 "Supply of Tinned Copper LUGs for fitting in Cable Size: Numbers 1500.00 4.36 6540.00

16 sqmm, Barrel Inner-dia: 6.4mm, Barrel Outter-Dia:

8.0mm, Barrel Length: 12.2mm, Stud Hole Center-dia:

10mm, Palm Width: 12.6mm, Thickness: 1.8, Lug

Length: 28-30mm,Thimble type: Ring/Fork type as per

site requirement. Inspection: Consignee"

123 123 "Supply of Tinned Copper LUGs for fitting in Cable Size: Numbers 1500.00 8.73 13095.00

35 sqmm, Barrel Inner-dia:13 mm, Barrel Outter-Dia: 17

mm, Barrel Length: 12.2mm, Stud Hole Center-dia:

10mm, Palm Width: 12.6mm, Thickness: 1.8, Lug

Length: 28-30 mm,Thimble type: Ring/Fork type as per

site requirement. Inspection: Consignee"

124 124 "Supply of Nut Bolts, Washer (Stainless Steel) as per the Set 2200.00 20.00 44000.00

site requirement (One set consists of 1 Nut, 1Bolt , 2

washer & 2 spring washer) Note :- Hex Nuts, bolts and

washers of size 5/16"" Inspection: Consignee"

125 125 "Supply of basic material to construct unit maintenance Numbers 35.00 4000.00 140000.00

free earth as per RDSO/SPN/197 Ver.1.0 or latest and

conforming to RDSO Drg. No. SDO / RDSO/ E&B/001 or

Latest. and RDSO Doc. No. STS/E/TAN/3006 Version 3.1

or latest. Necessary testing certificate of UL, IEC to be

produced. It consist of following: (a) Copper bonded

steel electrode of 3.0 m long, 17.2 mm dia with copper

bonding thickness of minimum macrons and UL listed

and marked = 1 no. Inspection: Consignee"

126 126 "Installation of Unit Maintenance Free Earth . It includes Set 35.00 3000.00 105000.00

( i ) Digging the earth to the required depth. (ii) Insertion

of electrode. (iii) Filling of earth enhancing compound

(Approx.30 Kg) (iv) Provision of exothermic weld

connections to copper Strip to the earth electrodes. (v)

This also includes supply of CC cover 1.5 ft x 1.5 ft. 1 ft

wall thickness 2 inch with cover 3-inch thickness

including Painting of Earth Pit As well. All material tools

and features required for weld will be arranged by

contractor. Inspection: Consignee. "

127 127 "Supply of Copper Strip for MEEB/SEEB (25X6)mm Metre 70.00 700.00 49000.00

Inspection: Consignee "

128 128 "Supply of Copper tape for BRC( 25X2) mm. Inspection: Metre 250.00 250.00 62500.00

129 129 "Installation of MEEB/SEEB/BRC with the insulators (As Numbers 700.00 25.00 17500.00

per the instruction of Site Engineer). Fitting materials &

Insulator (Dough Moulding Compound Conical type of

different Size) as per the site requirement to be supplied

by the contractor. Note: 'No' in the unit column indicates

'per insulator' "

130 130 "Supply and Execution of Exothemic Welds for more Numbers 300.00 418.00 125400.00

than 16 sqmm wire. This includes Welding Kit , Welding

Powder, Mould and other necessary materials. Note- No.

in unit column indicates per welding. Inspection:

131 131 "Supply and Execution of Exothemic Welds for upto 16 Numbers 1300.00 316.00 410800.00

sqmm wire. This includes Welding Kit , Welding Powder,

Mould and other necessary materials. Note- No. in unit

column indicates per welding. Inspection: Consignee"

132 132 Construction of cement concrete enclosure for earth Numbers 47.00 483.90 22743.30

electrode as per DRG. NO. PCSTE/ER'S DRG. NO.

SI/TYP/0097 dated 25.03.2025 or latest. This includes

supply of all materials by the contractor required for

cement concrete enclosure duly inspected by consignee.

133 133 "Supply of Earthing powder ( Earth Enhancement Kg 1050.00 47.50 49875.00

M a t e r i a l ) as per Para 8.2 of RDSO Spn. No.

RDSO/SPN/197 or latest Note :- Minimum weight of Bag

should be of 10 KG. Inspection: Consignee "

134 134 Supply of MS Fencing frame for ring earth area, location Metre 250.00 2540.00 635000.00

box and other S&T premises as per DRG. No. CWM

00223 or latest. (Height of fence would be of 1.5m)

Inspection: RITES

SEALDAH DIVISION-S AND T/EASTERN RLY

135 135 "FIXING OF FENCE AROUND THE RING EARTH AREA AND Metre 250.00 400.00 100000.00

OTHER MISCELLANEOUS WORKS TO BE EXECUTED. THIS

JOB INCLUDES CUTTING AND WELDING OF MS GRILL ,

DRILLING, CEMENT CONCRETING. THIS WORK TO BE

EXECUTED IN ONE RING EARTH AREA AS PER THE

INSTRUCTION OF RAILWAY SITE ENGINEER(S). ALL THE

MATERIALS (i.e SAND, CEMENT, STONE CHIP ETC) &

MANPOWER TO BE SUPPLIED & PROVIDED BY THE

CONTRACTOR EXCEPT MS GRILL FENCE . As per 'Typical

fencing for earthing S&T installation' Annexure-III (c) of

document no. RDSO-Sig0SPD(PROJ)/1/2020 ver 0.0 dtd

01/01/25. Note: Per foundation of fence would be of

250mm X 250mm with 300mm minimum depth. "

136 136 "Supply of 50mm x 6mm GI tape for interconnecting Metre 150.00 462.71 69406.50

earth electrodes.. Inspection: Consignee "

137 137 "Installation of GI Tape (50 X 6 mm) for connecting Main Numbers 35.00 80.00 2800.00

earth pit to other earth pit in case of loop earth. Note:

'No' in the unit column indicates 'per pair of earth pit'.

The GI tape shall be buried at Depth not less than 500

mm below the ground level. "

138 138 "Construction of Concrete Path Way (500 mm Width) Metre 150.00 2165.00 324750.00

from One Earth pit to the consecutive Earth Pit. &

Painting of Earth Pit As well as concrete path way. This

includes supply of Bricks, Cement, Sand, Stone chip &

Paint of good quality. "

139 139 "Segregation of Clean & Dirty wire ( Earth wire, wire Job 40.00 3000.00 120000.00

from unprotected sources,VHF antenna cable etc.) in SM

Room and OFC Room. This includes supply of PVC pipe &

PVC Trough of different sizes & fixing of it along with

laying of dirty cable through PVC pipe/Trough. It also

includes proper writing of "" DIRTY CABLE"" & "" CLEAN

CABLE"" on the cable tray or PVC Pipe. Note- Job. in unit

column indicates per Station."

140 140 Supply of 6 feet Heavy Duty Foldable Aluminium Ladder Numbers 10.00 4543.31 45433.10

(2 wayStepladder) with broad steps on main side with PF

at the top (PFSIZE:16"X12"). Make: Kalco/Werner or

superior. Inspection: Consignee.

141 141 "Supply of Aluminium Single Pole Platform step ladder, Numbers 1.00 14830.50 14830.50

Capacity 150 kilogram. Note: The ladder should have

Portable and Compact Telescopic Ladder with 14-Steps.

Inspection: Consignee."

142 142 "Supply of Telephone instrument single push button, Numbers 100.00 761.86 76186.00

Caller Id Landline Set. Make: Beetel C51 or superior

Inspection: Consignee"

143 143 "Supply of Telephone instrument single push button, Numbers 105.00 455.85 47864.25

without Caller Id Landline Set. Make: Beetel C11 or

superior Inspection: Consignee"

144 144 "Supply of open standard SIP phone. Make: Grandstream Numbers 10.00 4465.56 44655.60

GXP1610/Alcatel or superior. Inspection: Consignee"

145 145 "Supply of Telephone Rosette Box. Inspection: Numbers 205.00 32.97 6758.85

146 146 "Supply of Wireless Phone FCT to support LTE, 5 G Numbers 25.00 5180.11 129502.75

network , CLI function,LCD Display with blacklit, call Log

(missed/dialled/received), Battery Standby Time 50 Hrs,

Battery TalkTime 3 Hrs, with Alarm Clock withsnooz,

calculator, 2-way speakerphone with volume

(adjustable),low battery warning. NOTE- CUG SIM will be

Provided by Railway Make:Beetel or superior. Inspection:

147 147 "Supply of Telephone Line Cord (RJ11). Inspection: Numbers 100.00 41.52 4152.00

148 148 "Supply of Telephone Coil Cord (RJ11) Inspection: Numbers 100.00 56.77 5677.00

SEALDAH DIVISION-S AND T/EASTERN RLY

149 149 Supply & Installation of Automatic change over device Numbers 38.00 63837.00 2425806.00

for DAC / UFSBI/BPAC to Optical fibre, STM(E1) ,

standard 19"" rack mountable device consisting of two

E1 port supporting 120 Ohms interface; dual optical

ports with (1+1) hot stand by with SFP Module loaded 20

Kms driving distance and four V.21 /V.23 (E&M) 2W/4W

interfaces with auto change over mechanism to Four

Quad ports 2W/4W ; each port configurable as 2W or 4W

no restriction in configuration ; unit to support Potential

free contacts four numbers can be linked with data

logger / RTU for E1 Status , Quad Status & Power Supply

status ; Unit support front panel ressetable audiable

buzzer in case of main link fails (optical or E1) ; Unit to

support power OFF fail safe mechanism when the unit is

switched OFF the inputs is bypassed to the Quad cable

automatcially.Note-Prior approval is required by

engineers representative before supply of material .

Make/Brand:CYGNUS 845-4P/MRO-TEK-MAPLE-

4C(O)/Team engineer or superior Inspection: RITES.

150 150 "Supply, installation, testing and commissioning of Class Numbers 22.00 12500.00 275000.00

""B"" & ""C"" surge protection device all enclosed in

transparent box complete with internal wiring and LED

lamp to indicate status of SPD. The Class C SPD shall

have remote indication contact pluggability and visual

indication. Specification mentioned as per guideline of

RDSO/SPN/197 Ver.1.0 or latest and conforming to RDSO

Drg. No. SDO / RDSO/ E&B/001 or Latest. and RDSO Doc.

No. STS/E/TAN/3006 Version 3.1 or latest. Make-

ABB/Allied Power Solutions/OBO Bettermann OR superior

Inspection: Consignee "

151 151 "Supply of Layer-2 Manageable 24 Port POE switch Numbers 15.00 32407.25 486108.75

having 24 nos. 10/100/1000 Ethernet port with POE+

support and 4x1GE SFP optical Port with Loaded optical

module (4 nos.) with all accessories as per RDSO spec

RDSO/SPN/TC/83/2020 Rev 2.1 or latest. Make:

Cisco/Juniper/D-Link//HP/TP-Link or superior Inspection:

152 152 "Supply of Layer 2 fully Managed switch (Minimum 8+2 Numbers 18.00 20837.74 375079.32

ports manageable with 2 nos. Gigabit SFP port with

loaded optical module (2 Nos.) and 8 Nos. 10/100/1000

Mbps Ethernet port, POE+ support with all accessories

as per RDSO spec RDSO/SPN/TC/83/2020 Rev 2.1 or

l a t e s t Make D-link/Digisol/Cisco/Juniper or superior.

Inspection: Consignee"

153 153 "Supply, Installation and Commissioning of 16 port Numbers 1.00 245000.00 245000.00

router having 16 WAN x 02 Mbps (E1 G.703 interface) RJ

45 ports & Min. 04 gigabit ethernet LAN ports as Per

RDSO Spec RDSO/SPN/TC/84/2008 Rev.0 or Latest with

all required accessories. Note: Prior approval is required

by railway engineers representative before supply of

material. Make: CISCO/Juniper/HP or superior. Inspection:

154 154 "Supply, Installation and Commissioning of 8 port Router Numbers 1.00 147591.00 147591.00

with 02 LAN/WAN 10/100/1000 GE with SFP Combo Ports

with loaded SFP module & ( 08X02 mbps E1 G.703

interface RJ 45 ports as Per RDSO Spec

RDSO/SPN/TC/84/2008 Rev.0 or Latest With all required

Accessories. Note: Prior approval is required by Rly

engineers representative before supply of material.

Make Make -CISCO/Juniper/HP or superior. Inspection:

155 155 "Supply of 4 Port Router having 04 WAN x 02 Mbps (E1 Numbers 25.00 95200.00 2380000.00

G.703 interface) RJ 45 ports & Min. 02 gigabit ethernet

LAN ports as Per RDSO Spec RDSO/SPN/TC/84/2008

Rev.0 or Latest With all required accessories. Note: Prior

approval is required by Rly engineers representative

before supply of material. Make:CISCO/Juniper/HP or

superior Inspection: RITES "

156 156 "Supply of Gigabit Ethernet Media Converter Single- Pair 20.00 5197.00 103940.00

Mode as per RDSO/ SPN/TC/103/2013 ver.2 or latest.

Make:Digisol/TP Link or superior. Inspection: Consignee"

RDSO/SPN/TC/82/2020 Rev 2.0 or latest with latest

ammendments. Make: Nomous/Team engineer or

superior. Inspection: Consignee.

SEALDAH DIVISION-S AND T/EASTERN RLY

RDSO/SPN/TC/80/2020 Rev 2.0 or latest with latest

ammendments. MAKE- Team engineer/Nomus or

superior Inspection: Consignee."

159 159 "Supply of 4E1 to 4 Ethernet Converter. Make: CubeTel Numbers 15.00 16559.00 248385.00

or superior Inspection: Consignee."

160 160 "Supply of CAT-6 UTP RJ-45 patch cord (5mtr long) Numbers 50.00 217.28 10864.00

twisted stranded cable terminated with RJ45 modular

plugs at both the ends. TIA/EIA-568-C.2 standard or

latest, Insulation Material : High Density Polyethylene,

Outer Jacket: FR-PVC, Conductor diameter: 23 to 26

AWG, Conductor Metal : Bare Copper. Make D-

Link/Digisol or superior Inspection: Consignee. "

161 161 "Supply of CAT-6 UTP RJ-45 patch cord (3 mtr long) Numbers 54.00 197.18 10647.72

twisted stranded cable terminated with RJ45 modular

plugs at both the ends. TIA/EIA-568-C.2 standard or

latest, Insulation Material : High Density Polyethylene,

Outer Jacket: FR-PVC, Conductor diameter: 23 to 26

AWG, Conductor Metal : Bare Copper, Make D-

Link/Digisol or superior Inspection: Consignee. "

162 162 "Supply ofCAT-6 UTP RJ-45 patch cord(1M length) Numbers 4.00 161.97 647.88

twisted stranded cable terminated with RJ45 modular

plugs at both the ends. TIA/EIA-568-C.2 standard or

latest , Insulation Material : High Density Polyethylene,

Outer Jacket: FR-PVC, Conductor diameter: 23 to 26

AWG, Conductor Metal : Bare Copper, Make D-

Link/Digisol or superior Inspection: Consignee."

163 163 "Supply of passthrough RJ-45 Connectors suitable for Numbers 1050.00 6.66 6993.00

STP/UTP cables, confirming to IS 1293:2019 or latest.

Make:-D Link/Digisol or superior Inspection: Consignee."

164 164 Supply of frame, surface box and white cover plates for Numbers 30.00 484.75 14542.50

Two modules. This also includes supply of RJ-11

Telephone sockets with level holder Jack type, RJ-45 LAN

sockets Jack Type and blanking plates for one modules.

Make: D-Link/Legrand or superior. Inspection: Consignee

165 165 Fixing of frame, surface box and white cover plates for Numbers 30.00 121.19 3635.70

Two modules. This also includes fixing of RJ-11

Telephone sockets with level holder Jack type, RJ-45 LAN

sockets Jack Type and blanking plates for one modules.

166 166 "Supply of 2.0 MP IR IP Network Dome Camera with all Numbers 4.00 3789.83 15159.32

accesssories, Image Sensor: 1/2.7"" Progressive Scan

CMOS, Lens type: 2.8mm, 4 mm, 6 mm, resolution: 1920

x 1080,Interface: 1 RJ45 10M/100M self-adaptive

Ethernet port. Power 12 VDC ± 25%, 0.4 A, max. 5 W,

Ø5.5 mm coaxial power plug PoE: 802.3af, Class 3, 36 V

to 57 V, 0.2 A to 0.15 A Make: Hikvision/CP PLUS or

superior Inspection: Consignee."

167 167 "Supply of 2 MP EXIR VF IP Bullet Network Camera with Numbers 24.00 7105.93 170542.32

all accesssories, resolution: 1920 x 1080, Lens

Type:Varifocal Lens, motorized lens, 2.8 to 12 mm,

ImageSensor: 1/2.7"" Progressive Scan CMOS, Power

supply:12 VDC ± 25%, 0.9 A, max. 11 W, Ø5.5 mm

coaxial power plug, PoE: (802.3af, Class 3, 36 V to 57

V),0.23 A to 0.36 A. Make: Hikvision/CP Plus or superior

Inspection: Consignee. "

168 168 "Supply of 23.8 Inch Full HD Led Backlit IPS Panel Numbers 15.00 11779.66 176694.90

Monitor. Make-LG/Samsung or superior. Inspection:

Make:Honeywell/MX or superior Inspection:Consignee.

Make:Honeywell/MX or superior Inspection:Consignee.

171 171 "Supply of 4+2 POE switch (Minimum 4+2 ports Numbers 12.00 4940.00 59280.00

manageable with 2 Uplink Port Switch for CCTV Camera

and Networking and 4 fast ethernet port. Make D-

link/Digisol or superior. Inspection: Consignee."

SEALDAH DIVISION-S AND T/EASTERN RLY

172 172 Supply of 8 Channels (NVR) network video recorder Numbers 12.00 9966.10 119593.20

having IP Video Input:8, HDMI Output: 4K (3840 x

Format:H.265/H.265+H.264/H.264+, Recording

Resolution: 12 MP/8 MP/6 MP/5 MP/4

MP/3MP/1080p/UXGA/720p/VGA/4CIF/DCIF/2CIF/CIF/QCIF,

Network Interface:1 RJ-45,10/100/1000 Mbps self-

adaptive Ethernet interface, RJ-45 10/100 Mbps self-

adaptive Ethernet interface, 2 SATA interfaces, Up to 10

TB capacity for each HDD, USB: Front panel: 1 x USB 2.0;

Rear panel: 1 x USB 2.0,Third-party network cameras

supported. Make: Hikvision/CP PLUS or superior.

Inspection: Consignee

173 173 "Supply of 16 Channels 4K Network Video Recorder Numbers 4.00 18950.00 75800.00

(NVR) with Support 2 SATA HDDs up to 20TB, 2 USB

ports(2.0), HDMI / VGA simultaneous video output,H.265,

H.264+, H.264, JPEG format, Video output: Video Output

720.Third-party network cameras supported. Make: CP

Plus-UNR-4K2162-V3 /Hikvision or superior Inspection:

174 174 Supply of 4TB Windows Surveillance Hard Numbers 12.00 7575.28 90903.36

Disk,compatible to all latest OS, Form Factor:

3.5,Interface: SATA 6 Gb/s, Cache (MB): 64, Water &

Shock Resistant Make: Toshiba/Seagate or superior.

Inspection: Consignee.

175 175 "Supply of Wireless Wi-Fi Gigabit Router with 4G/5G SIM Numbers 12.00 5366.40 64396.80

Card support. Make:D-Linl/TP Link/CP PLUS-CP-XR-DE21-

S-V2 or superior Inspection: Consignee. "

176 176 "Supply and Installation of 1KVA Online UPS with min. 30 Numbers 8.00 21508.92 172071.36

minute backup full load condition along in with 03 Nos.

12v/26Ah external battery (Quanta/Exide OR superior)

with terminal, battery rack & accessories set. Make:

Microtek/Numeric/Emerson (Vertiv)/ APC or superior

Inspection: Consignee. "

177 177 "Supply of Line interactive 600VA UPS, battery:12V/7Ah Numbers 20.00 3462.18 69243.60

SMF-VRLA confirming to JISC-8702 Pt 1,2 &3, IP-21

protection, ABS Enclosure, Protection against short

circuit, over voltage and over load, Input Voltage:

230V/AC, Surge Protected 6A, 2/3 Pin Output, cable

length: 1.22 m, Output Power Capacity:360Watts/ 600

VA Make: APC/Mircotek/Numeric or superior Inspection:

178 178 "Supply of Cable Route Locator/Tracer set suitable for Numbers 1.00 348066.10 348066.10

detecting underground armored OFC, Telecom, Power &

Signalling Cables with LCD graphics, Display

active/passive modes. {It must have a rechargeable

battery cum charging facility for both transmitter &

receiver along with other accessiories} Make & Model :

Radiodetection RD-8200 G/ Stanley STLOC10 or

superior. Item to be supplied after successful

demonstration and Approval of Railway. Inspection:

179 179 "Supply of optical power meter with Visual Fault Locator, Numbers 11.00 13994.48 153939.28

as per TEC spec. GR/OPM-01/03 Feb 2005 or latest. with

compatible adapter, Charging cable & all required

accessories. Note-Item to be supplied after successful

demonstration and Approval of Railway. Inspection:

180 180 Supply of digital Multimeter. Make:RISHABH 410/Fluke Numbers 10.00 2940.19 29401.90

101 or superior. Inspection:Consignee.

181 181 "Supply of Digital cable insulation tester for Numbers 17.00 7366.10 125223.70

measurement of Cable insulation resistance with auto

range 0-500V DC. Item to be supplied after successful

demonstration and approval of railway. Make: Rishabh

INSU-20/Metravi/motwani or superior.

Inspection:Consignee."

SEALDAH DIVISION-S AND T/EASTERN RLY

182 182 Supply of Digital Cable network tester (LAN Tester) to Numbers 12.00 510.40 6124.80

Check RJ11, RJ45 and BNC connectors, Full LED

indication lights on both main and remote unit, to Verify

continuity, opens, shorted or cross wire paired, Indicator

LED Lights, Power 9V Alkaline Battery, Electricity : 25mA

, make: Dlink or superior. Inspection: Consignee

183 183 "Supply of true RMS Digital Multimeter. Make- Rishabh Numbers 5.00 25307.63 126538.15

6016/Fluke or Superior. Item to be supplied after

successful demonstration and Approval of Railway.

Inspection : Consignee "

184 184 "Supply of Passthrough Crimping tool, Modular Plugs Numbers 22.00 734.93 16168.46

8P8C RJ-45, 6P6C RJ-12 and 4P4C RJ-11, 7.5 inch steel

construction body, All-steel handles (with padding),

Suitable for 22-26 AWG wires, Built-in cable stripper with

stop to ensure correct strip length continuity tester.

Inspection: Consignee "

185 185 Supply of Digital Cross Talk Meter measuring set as per Numbers 4.00 45000.00 180000.00

SPN IRS TC: 45/88 or latest with latest amdt. Make: Anu

Vidyut or superior Inspection: Consignee

186 186 Supply of Transmission measuring set (TMS kit) Numbers 4.00 22000.00 88000.00

complete with tone generator and Db meter with

Complete set with all connection lead & Accessories as

RDSO specification IRS:TC-43/87 or latest with latest

ammendments. Make: Anuvidhyut/Aplab or superior.

Inspection: Consignee

187 187 Supply of Digital Earth Resistance Tester for Numbers 2.00 7424.58 14849.16

measurement of earth resistance with Range -0.5 Ohms

to 500 Ohms. Rishabh/WACO or Superior. Item to be

supplied with accessories after successful demonstration

and Approval of Railway. Inspection: Consignee

188 188 Supply of 25W VHF power meter suitable for testing and Numbers 4.00 20000.00 80000.00

measurement in Frequency range typically 100-300

MHz. measuring Forward Power, Reverse Power. Note-

Item to be supplied after successful demonstration and

Approval of Railway Make-NISSEI RS-502/Surecom SW-

102 or Complete set with all connection lead &

Accessories. Inspection: Consignee

189 189 "Supply of Soldering Iron 65W/220V, 65 watts pencil bit Numbers 27.00 207.31 5597.37

Soldering Iron Handel Material: Wooden/FRP, 1.5Mtr

Long Wire, Capacity 230V-240V

Make:Soldron/Toni/Shakti or superior. Inspection:

190 190 "Supply of Suction and blower vaccum cleaner 700 Watt. Numbers 5.00 3987.00 19935.00

Filter Type: HEPA Filter, Capacity: 0.8 litres or more,

Noise Level: 80 dB or better along with all accessories

such as 2 in 1 small brush, cervice nozzle, hose pipe,

extension tubes, blower nozzle, floor cum carpet brush

with power cord . Make: Eureka Forbes/Inalsa or superior

Inspection: Consignee "

191 191 "Supply of Electric Drill machine 600 Watt with Technical Numbers 8.00 3639.83 29118.64

Specifications: Speed upto 3000 RPM , Rated Torque of

Min 1.4 Nm, Impact rate upto 48000 BPM, along with 01

Nos of 4 mm, 5 mm, 6 mm, 8 mm and 10 mm drill bit.

Make:Bosch GSB 600/Stanley or superior. Inspection:

192 192 Supply of Hand held rechargeable LED Torch 5W with Numbers 25.00 624.71 15617.75

upto 10 hr back up with 3.7V 3000mAh Lithium-Ion Re-

Chargeable Battery. Make: Havells/Nippo or superior

Inspection: Consignee.

193 193 "Supply of All in one PC 13th Generation Intel Core™ i3 Numbers 2.00 52960.00 105920.00

processor or better, Windows 11 Home or latest, 60.5

cm (23.8) diagonal FHD display ,8 GB DDR4 RAM, 512

GB SSD Solid State Drive, Wireless Keyboard and Mouse

, True Vision 1080p FHD IR tilt camera and operating

system with Pre-Installed MS Office Home, 02Nos 128GB

Pen drive. Make:HP/DELL/ASUS or superior Inspection:

SEALDAH DIVISION-S AND T/EASTERN RLY

194 194 "During the block working period of any department or Man- 75.00 4859.00 364425.00

dismantaling / refixing / shifting and other allied work of Days

Telecom department as-(i) Unearthing Defective Cable &

OFC Joints.(ii) Jointing/Splicing of Cables/OFC for

temporary or permanent restoration of cables/OFCs at

any time wherever instructed. (iii) Searching of

bad/defective cables/OFCs joints and Jointing/Splicing of

Cables/OFC for temporary or permanent restoration of

cables/OFCs (iv) Small Trenching Work for replacing

Defective Cable/OFC. (v) Cleaning of OFC Hut/SM

Panel/Exchange/DATACOM equpments/TIBs, CIBs/ and

Replacement of Speakers , LS cables. (vi) Carrying

Heavy Telecom Materials such as Quad Cable, Charger

from one place to another. (vii) Carrying & Depositing

Heavy Scrap materials from different stations to

Sectional Store And Other Miscllanious Works To Be

Executed. This Job Includes Cost Of Releasing Of

Telecom Equipments, Gears & Devices And

Reconnection Of The Same After the Work. The work

may be executed at any time of day or night, as per the

instructions of the Railway Site Engineer(s).. The team

should have sufficient equipment like OTDR, splicing

machine, power meter etc. Vehicle arrangements for

transportation shall also be made by the firm.. 1.Cable

Jointer Cum Wire Man =1Nos (2) Ofc Splicer =1No

(3).khalasis/ Helpers=3Nos shall be provided per

day/Night, either individually or as a group or as

specified by the Railway railway & Payment shall be

made based on the Basic Rate per Day, as applicable to

the category of manpower deployed (Unskilled/Semi-

skilled/Highly Skilled) and as specified in Annexure-I.

Note: Mandays in unit column indicates Per Day/Per

Night and all required material during the work provided

by the Railway."

195 195 "Supply of All in one inkjet printer (A4 size paper) with Numbers 5.00 8852.81 44264.05

FAX,scan, copy & print function. Make: Canon PIXMA / HP

Deskjet Ink Advantage 4178 / Epson or superior.

Inspection: Consignee."

196 196 "Supply of Maintenance console Intel Core i5 11500 8 GB Numbers 5.00 45508.47 227542.35

RAM/ 1000 GB HDD/SSD/ Windows 11 home or latest

with Pre-Installed MS Office Home, HD 720p Camera &

Keyboard & wireless Mouse, 1Nos laptop bag, 2Nos

64GB Pen drive. Make:HP/DELL/ASUS or superior.

Inspection: Consignee "

197 197 Dismantaling & Release of all old cable (data/LS & power Metre 2000.00 5.39 10780.00

cable both) as per instruction of site engineer &

transporting of the same to store.