CWE/P-73/2020-21 SPECIAL REPAIR TO BLDG NO P-56, P-57, P-70 OF OR MD ACCN AT AND PROVN OF SEPTIC TANK/SOAKAGE WELL AND ALLIED INFRA FOR TOILET OF GD POST, OR LINE / MD ACCN AT MIL STN UNCHI BASSI UNDER GE (SOUTH) PATHANKOT

Amount

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5 Sqm each including taking out hold fast complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5Sqm and not exceeding 4Sqm each including taking out hold fast complete all as specified and directed.

M&L for factory made Glazed and skelton shutters 35mm thick of 2nd class hard wood rail & style open rebated and prepared to receive glass or wire gauze etc. shutters (with shash bars any numbers), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc., size of members of shutters as per IS 1003 (Part-I) kiln seasoned and pressure treated all as specified.

M&L for Plain framed factory made 35mm thick shutter of 2nd class hard wood rail & style (two panel) with lock rail and panel of 9mm BWP commercial plywood or 9 mm veneered particle board with commercial veneering on both faces , the size of rail and style as per IS 1003 (Part-1) kiln seasoned and pressure treated all as specified.

M&L 1.25mm thick pressed steel frames with one shop coat of red oxide primer 105 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges (ISI marked), lock strike plate and hold fast after tarring of hollow portion of frame complete all as specified and directed

M&L 1.25mm thick pressed steel frames with one shop coat of red oxide primer 125 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges (ISI marked), lock strike plate and hold fast after taaring of hollow portion of frame complete all as specified and directed.

M&L PCC 1:3:6 Type C-1 (using 20mm graded crushed stone) as in back filling of pressed steel frames and similar work complete all as specified and directed.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification and drawing complete alll as specified .

S&F factory made Solid Panel PVC door shutters 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement or tiles and plain colour PVC sheets for top rail lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at site as per specification in SSR Part-I complete all as specified and directed.

M&L Steel windows of Z section with side hung shutter including hinges with steel handles, 2 Nos steel tower bolts 100 mm long peg stay complete with glazing bars, dovetailed or welded including locking arrangements and one shop coat of zinc primer complete all as specified and directed by Engr-in-Charge.

All as per Srl item No 10 here-in-before but without glazing bars

M&L Steel windows or ventilators fixed type, with glazing bars complete all as specified and directed by Engr-in-Charge.

M&L Steel ventilators with top hung shutter including hinges, steel peg stay complete all as specified and directed by Engr-in-Charge.

M & L framed work such as grills, grating etc with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, barrel, iron doors, ladders, balusters, walkway, frame work of water tanks and similar work confirming to Fe-290 Gde E-165 complete all as specified.

M & L galvanised mild steel wire cloth 0.46 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified.

M & L 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified.

M & L 3 mm thick figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified.

S & F mild steel sliding door bolts, stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolts plate and two on staple plate, 300mm long, ISI marked all as specified.

Supply and fixing Aluminium anodised, barrel tower bolts of extruded section of size 150mm ISI marked and fixed, complete all as specified and directed.

M & L Aluminium alloy handles (ISI marked), cast type, anodised of size 150mm and fixed, complete all as specified and directed.

S & F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, two legged, overall length of cover plate 50 mm complete all as specified and directed.

M & L Mild steel butt hinges, medium weight, cold rolled (ISI marked),100mm long , complete all as specified.

M & L for 25mm thick flush shutter, solid core construction, with particle board core and plywood face panels, commercial type on both sides, including fixing Ist class softwood beading of size 25x20mm over all sides and fixed with screws to frame all as ppecified and directed.

S & F Butt hinges, medium weight cold rolled mild steel, 75mm size, complete all as specified and directed

S & F hasp and staple,100 mm long aluminium anodised, including bolt to hinge plate and fixed with screws complete all as specified. ISI Marked

S & F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified

Supply and fixing in repairs, 150mm mild steel ordinary rat tail rod pattern springs including roller and roller plate fixedto pressed steel frame/ MS frame/ wooden chowkhats including necessary fixing arrangement and welding work as required complete all as specified.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Glazed ceramic coloured tiles in skirting/dado 300 x 450 x 8mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match required shade over and including 15 mm thick cement plaster in cement mortar 1:4 as in backing coat rough finished surface complete all as specified.

M&L for edge cut joint free glazed/matt finish coloured or printed ceramic tiles size of each tile 600 x 600 x 10 mm thick exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over screed bed 15 mm thick in cement mortar 1:6 complete all as specified.

All as per Srl item No 31 here in before but as in skirting on 10 mm thick rendering in Cement Mortar 1:4 complete all as specified and directed

M & L Plain Cement Concrete 1:2:4, type B-1 (using 20mm crushed stone aggregate), avg 25mm thick as in sub base complete all as specified.

M&L for chequered cement concrete tiles 30cm x 30 cm x 22 to 25 mm thick, set jointed and pointed in neat cement slurry with grey cement and pigment in floors

M & L for providing 100mm thick plain Cement Concrete 1:4:8, type D-2 (using 40mm crushed stone aggregate), as in plinth protection, flooring etc laid in alternate bays finishing even and fair without using extra cement complete all as specified

M & L for providing 75mm thick plain Cement Concrete 1:3:6, type C-1 (using 20mm crushed stone aggregate), as in plinth protection, flooring etc laid in alternate bays finishing even and smooth without using extra cement complete all as specified.

M&L roughening surfaces of old concrete surfaces by picking sweeping, cleaning and washing down with water to remove dust etc including taking down existing roof treatment and brushing neat cement slurry @ 3 Kg/Sqm all as specified and directed

M&L screed bed or bedding layer 10mm thick in cement mortar 1:4 mixed with water proofing compound on concrete surfaces in roof, complete all as specified and as directed. Note : WPC shall be measured and paid separetely

M & L for providing and laying of water proofing treatment of roof APP (Atactic Polyproplylene) modified prefabricated five layer 3mm thick water proofing membrane, super thermply non woven polyester mat reinforcement of 160 gsm, weight of membrane @ 3.6 Kg/Sqm over a solvent based bitumen primer @ 0.4 Ltr / Sqm by the same manufacturer conforming to IS:3384-1986 , The membrane shall be laid using bitmun torch.The end lap should be 150 mm and the side lap must be minimum 100 mm the membrane shall be first laid up to the parapet wall junction and then shall be overlapped with another membrane (flashing) with an overlap covering up to a distance of 300mm. In case parapet height is less than/ up to 500 mm, membrane shall be terminated at the top of parapet.All rain water pipe opening shall be suitably sealed with the APP membrane all as specified and directed. Note: The work shall be executed through authorised applicator by the manufacurer of membrane as specifeid in particular specificaction.

M & L PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in roof padding with liquid WPC laid to slopes as directed and avg thickness 25mm, and finishing the surfaces even & smooth without using extra cement, complete all as specified and directed. Note : WPC shall be measured and paid separetely

M & L PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate), fas in copings, benching , kerb or mud stops,rounded or chamfered angles and edges, including necessary form work complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically described (reinforement cut as required to facilitate demolition), complete all as directed by Engineer-in-Charge.

M & L precast cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregates) as in cover slab,cover etc including necessary moulds/ form work for septic tank/soakage well/manhole cover and set in cement mortar 1:6, complete all as specified and directed.

M&L RCC (nominal mix ), 1:2:4 Type B-1, in slabs supported on walls, beams and columns in floors, roofs, landings,balconies, canopies deck slabs and in shelves and the like complete all as specified and directed.

M & L form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exceeding 200mm thick (horizontal or sloping) for flat rough finished surfaces of concrete complete all as specified and directed.

M & L mild steel TMT bars 6mm to 8mm dia. as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L TMT bars 10mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L mild steel frame work as in frames of manholes covers etc and the like including cutting/welding and similar work conforming to Fe 290 Gde - E- 165 complete all as specified and directed.

Material and Labour for brushing & cleaning surface of sunken floors & surface painting with layer of blown bitumen of any penetration and applied hot @ 1.7kg/Sqm complete all as specified and directed.

M & L plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified.

M & L 50mm thickness plain cement concrete 1:2:4 type B-1 (20mm graded crushed stone aggregate) as in sunken floor finished even and fair using water proofing compound complete all as specified and directed. Note : WPC shall be measured and paid separetely

M&L 200mm thick PCC type B-1, 1:2:4 (20mm graded aggregate) in sub base complete all as specified and directed.

M&L 15mm thick rendering in cement mortar 1:3 on fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement and with water proofing compound as in sunken floor or external plaster , complete all as specified

Supply only liquid water proofing compound complete all as specified

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and as directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

M&L brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar 1:6, complete all as specified and directed.

All as per item No.57.00 here-in-before, but except bricks.

Brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 mtr mean radius and built in cement mortar 1:4 complete all as specified and directed.

All as per item No.59.00 here-in-before, but except bricks complete all as specified and directed.

M & L brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4, complete all as specified.

M&L 15mm thick rendering in cement mortar 1:4 on fair faces of brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including necessary form work complete all as specified.

M & L plain cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in surface channels and drains, complete all as specified.

M & L Concrete bed in PCC 1:3:6 type C-2 to drain pipes of 150 mm dia including packing under and haunching against the sides of pipes after laying and testing complete all as specified.

Taking down old broken cast iron pipes from existing sewage line or along plumbing stack along the walls including necessary excavation in trenches where required, removal of surplus soil and returning filling in complete, supplying, laying in trenches or along the walls with MS clamps of standard specifications and including S & F of new 110mm dia cast iron (sand cast) pipe complete all as specified and directed by the Engineer-in-Charge

All as per item No.66.00 here-in-before, but for 75 mm dia PVC (SWR) pipes complete all as specified and directed

M&L reinforced concrete pipe, class NP2, 150mm bore, laid in trenches and jointed on concrete bed complete including testing complete all as specified and directed (concrete to be measured and paid separately)

M & L Taking down damaged SGSW pipes from existing lines including necessary excavation of old fitted in trenches, supply, laying and jointing of Reinforced concrete class NP2, 150mm dia including testing, haunching against the sides of pipes in PCC (1:4:8) type D-2, and returning, filling in disposal of surplus soil to a distance not exceeding 50 m complete all as specified and directed.

M & L cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel ( 1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified.

M & L loose filling with broken stone boulders aggregates of gauge 40 mm well graded in soakage pits, dispersion trenches complete all as specified & directed.

M & L loose filling with 40mm uniform size coarse stone aggregate as in soakage pits / dispersion trenches complete all as specified & directed.

M&L PVC (SWR) 110mm bore pipes single socketed, in any length with rubber ring joints, fixed to walls using clamps/ laid in floors complete all as specified and directed.

M&L PVC (SWR) 75mm bore pipes single socketed, in any length with rubber ring joints, fixed to walls using clamps/ laid in floors complete all as specified and directed.

M&L for preast hume pipe septic tank of dia 0.75 mtr and length 2.40 mtr designed to carry sewage and sludge water, excavation in any type of soil, returning filling and removal, 100mm thick PCC 1:4:8 in base of foundation, vent shaft, connection etc,. complete for 10 user fixed in repair complete all as specified and directed. Make :- Mahindra industries or equivalent approved make as directed by GE.

S & F 100mm cast iron soil, waste and vent pipes in any length with or without ears, with cement joints laid in trenches or in floorscomplete all as specified and directed.

S & F cast iron cowls of 100mm dia complete all as specified and directed.

S & F PVC (SWR) cowls 110 mm ISI marked complete all as specified and directed.

S & F PVC (SWR) junction single, (Single T) equal or unequal for 110 mm dia bore with access door complete all as specified and directed.

S & F PVC (SWR) junction single, (Single T) equal or unequal for 75 mm dia bore with access door complete all as specified and directed.

S&F PVC (SWR) bends any radius of 110mm dia bore pipe with access door ISI marked complete all as specified and directed.

S&F PVC (SWR) bends any radius of 75mm dia bore pipe with access door ISI marked complete all as specified and directed.

S&F PVC (SWR) traps 110/110 mm bore 'P' type complete all as specified and directed.

S&F PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) multi floor trap 75mm dia, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F stainless steel Plate rack of size 900 x 600 mm with 1mm thick steel complete all as specified and directed.

S&F Drapery rod (curtain rod) of 25 mm dia, fancy type, of length 1.8 m each complete with and including end globe, end brackets/ caps complete all as specified and directed.

Taking down cement plaster or cement line plaster on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

M&L 10mm thick rendering in cement mortar 1:3 on fair faces of brick or concrete surfaces as in ceiling & finishing the surface even and smooth without using extra cement including applying three coats of white wash including preparation of newly plastered surfaces of ceiling complete all as specified.

M&L 15mm thick rendering in cement mortar 1:4 on fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement, including applying two coats cement base paint of approved brand including preparation of newly plastered surfaces of wall complete all as specified

M&L 15mm thick rendering in cement mortar 1:6 on fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement, including applying two coats cement base paint of approved brand including preparation of newly plastered surfaces of wall complete all as specified

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete all as specified and directed.

M&L GI tubes of 15 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

All as per Srl item No 93 here-in-before but fixing only.

M&L GI tubes of 20 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

All as per Srl item No 95 here-in-before but fixing only.

S&F Chromium plated brass shower rose with or without swivel joints, 125 mm size including fixing to steel pipe or union, all as specified.

Supply and fixing bib taps 15mm bore of cast copper alloy chromium plated (ISI marked) fancy type, screwed down, high presure, screwed both ends for iron pipe or for brass ferrule, complete all as specified and directed.

Supply and fixing in repairs, 15mm bore, angle valve fancy type cast copper alloy chromium (ISI marked), with crutch or butter fly handle high pressure screwed both ends for iron pipe or for union and fixed complete all as specified and as directed.

M&L pillar taps, cast copper alloy with with capstan heads chromium plated fancy type screwed down high pressure with or without lettered hot or cold with long screwed, shanks and fly nuts, screwed for iron pipe 15mm dia complete all as specified and as directed.

S&F CP brass stop valve concealed type 15 mm dia fancy type chromium plated with long sank and cup complete all as specified and as directed.

S & F 20mm bore gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe fixed complete all as specified.

Supply and fixing in repairs, PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC flush pipe for low level cistern including all joints , complete all as specified.

S&F tubular towel rail, 20mm dia, D type, 60cm long between flanges Brass chromium plated, fixed with rawl plugs all as specified and directed

M&L Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300gms) complete all as specified and directed.

S & F PVC connection 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

Supply and fixing in repairs, Vitreous china (flat back or angle back type) wash hand basin white, flat back, size 450 x 300 mm including brackets any size, PTMT waste coupling 32mm,waste pipe 32 mm dia cutting for and pinning in ends of brackets or erecting stand complete, all as specified and as directed.

Supply and fixing in repairs, Vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, white, with integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe of 32mm dia and syphonage pipe etc, and including concrete bedding complete, all as specified and as directed.

Supply and fixing rotational moulded polythene water storage tank, white coloured, tripple layer cylindrical vertical with closed top 500 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug and PTMT ball valve 20mm, high pressure with polyethelyne float and fly nuts complete all as specified and directed.

M&L Preparation of new or untreated wood or wood based surfaces of any description exceeding 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L Preparation of new or untreated steel surfaces of any description exceeding 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red primer complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint over steel surfaces of any description not otherwise described over 10 cm in width or girth including preparation of old painted surfaces complete all as specified and directed.

M&L for preparation of old surfaces and applying two coats of white wash on ceiling including preparation complete all as specified.

M&L for preparation of new surfaces and applying three coats of white wash on ceiling including preparation of new surface complete all as specified.

M&L for preparation of new plastered or unplastered new surfaces of wall including and applying two coat of acrylic bound distemper over a coat of primer on walls complete all as specified.

Preparation of old plastered/ un-plastered wall surfaces including brooming down or steel wire brushing, scraping down, smoke soot, mould, moss, efflorescent salts, trading oil and greasy spots, and applying two coats of acrylic distemper on walls including cornices, pilasters etc, complete all as specified.

M&L for preparation of new plastered or unplastered surfaces of wall including and applying two coats of cement base paint over a coat of primer on walls complete all as specified.

M&L for two coats of cement base paint including prepatation old surface to match the shade as per colour scheme/pattern complete all as specified.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc set in any type or mortar complete all as specified.

M&L 18 to 20mm thick granite (of approved type colour) work (table rubbed & polished) in jambs, pillars, window cills, cooking plateform laid over and including 15mm thick cement screed (1:4) and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the colour of granite stone including cutting and moulding the edges where ever directed by Engr-in-charge, complete all as specified.

M&L Machine cut kota stone slab flooring 16-18 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with wax polish to make it square or rectangular, includingrounding to edge of stone slabs one edhe as in steps, complete all as specified.

M&L for Kota stone slab 10-12mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing & complete aggregate all as specified & directed.

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

M&L Point wiring for 15 Amp socket point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel terminal boxes (for mounting switches /sockets/ regulators/ceiling roses etc ) made of not less than 16 gauge MS sheet and 6cm depth covered with 3mm thick laminated bakelite sheet fitted with brass screw and washers and including 1.5sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : a) Rate for cutting chases for conduits and sinking for boxes and making good to wall, floors deemed to be in each point etc. b) On RCC roof ceiling PVC conduit shall be provided on surfaces of any necessary point with proper fixing clips and no extra cost shall be paid for job etc all as directed

All as per above item no 125.00 here in before but for one 3 pin socket outlet 5 amp on independent board all as specified and directed.

All as per above item no 125.00 here in before but for one 3 pin socket outlet 5 amp on same board all as specified and directed

All as per above item no 125 here in before but one for light point controlled by 2 nos two way switches complete all as specified.

All as per above item no 125 here in before but one bell/buzzer point controlled by one push button on the same board with other inner switches or independent with cable 1.5 Sqmm size complete all as specified.

M&L Point wiring with 2.5 Sqmm FRLS, PVC insulated unsheathed multistranded copper conductor cable in and including rigid PVC concealed conduit medium grade of sunk boxes with suitable thickness plastic laminated sheet cover 3mm thick for one 3 pin socket outlet 15mm on independent board including continuous 2.5 Sqmm FRLS, PVC insulated and including unsheathed copper conductor cable (multistranded) as earth wire to common earth dolly, complete all as specified. Note : a) Rate for cutting chases for conduits and sinking for boxes and making good to wall, floors deemed to be in each point etc. b) On RCC roof ceiling PVC conduit shall be provided on surfaces of any necessary point with proper fixing clips and no extra cost shall be paid for job etc all as directed

M&L Point wiring with 4 Sqmm FRLS, PVC insulated unsheathed multistranded copper conductor cable in and including rigid PVC concealed conduit medium grade of sunk boxes with suitable thickness plastic laminated sheet cover 3mm thick for one 3 pin socket outlet 15mm on independent board including continuous 4 Sqmm FRLS, PVC insulated and including unsheathed copper conductor cable (multistranded) as earth wire to common earth dolly, complete all as specified. Note : a) Rate for cutting chases for conduits and sinking for boxes and making good to wall, floors deemed to be in each point etc. b) On RCC roof ceiling PVC conduit shall be provided on surfaces of any necessary point with proper fixing clips and no extra cost shall be paid for job etc all as directed.

S&F Switch piano flush type 5 Amp single pole one way, 5 amps, 230 Volts (ISI marked), complete all as specified.

S&F switch bell push 5 amp, 240 volt, flush type (ISI marked) , one way complete all as specifed.

S&F socket outlet 2 in 1, 3 pin, 5 Amp flush type ,complete all as specifed.

S&F switch socket outlet , 6 pin, 5/15 amps multi purpose 2 in 1 flush type , 230 volts complete all as specifed.

M&L Switch piano flush type 5 Amp single pole two way, 5 amps, 230 Volts (ISI marked), complete all as specified.

Disconnecting and taking down ceiling fan 1400mm sweep / exhaust fan upto 450mm sweep for servicing, strip opening of fan including cleaning, greasing and servicing complete at site and reassembling and refixing in existing/new location after replacing rubber reel, fixing bolts and nuts with lock pins, connectors for complete fan including writing MES No. all as required and directed by Engr-in-charge and connecting up with new flexible twin core copper conductor cable, testing complete after servicing and fixing for smooth and noise free operation all as specified and directed.

M&L Ceiling rose, 3 phase/bakelite 65x50mm two or three terminal size 65 x 20 mm isolated body fixed on PVC round block complete all as specified.

S&F in replacement SPN DB 8 way sheet metal enclosure factory made (Double door) type IP-43 Protection. Isolated Neutral,Door earthing, cement spill protector, IK-08 complete, single pole and neutral, 240 volts, 50 Hz, 8 way with 200Amps rated copper bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

S & F in replacement MCBs single pole link (SP) 6 to 32 Amps with 10 KA breaking capacity of 'C' series in distribution complete all as specified and directed

S & F in replacement MCBs single pole, neutral link (SPN) upto 32 Amps with 10 KA breaking capacity of 'C' series in distribution complete all as specified and directed

Supply and Fixing decorative box type fitting 4 feet long for LED tube 1x20W LED including LED tube 4 feet long of 20W having bipin holder, connector block etc complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed

Supply and Fixing corner street light fittings 24 watt LED new generation energy saving and environmental friendly long life versatile pressure die cast aluminium with mid power LEDs as light source and exclusively designed polycabonate cover alongwith electronic driver complete all connecting electrically using cord flexible 3 core copper flexible cable of size 23/ .0076 including galvanised iron bracket 1.2 mtr long of 25 mm dia incl suitable clamps with nut, bolt and washer and fixing the light to the building all as required at site or directed

M&L Lamp holder Polycarbonate type with back plate having matching colour to holder for angle/batten fittings complete all as specified and directed.

S&F LED Lamp 230 volts,50 Hz,inverter LED 18/20 watt ,lumen 900 lm, rated current 0.045A, CRI less than 80, Charging time 8 to 10 Hours, operating temperature -10 to 50 degree celcius,back time 04 Hours, complete all as specififed and direccted.

Supply and laying in replacement of existing unserviceable/ burnt submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 4 sqmm drawing into and including concealed PVC rigid non metallic conduit of 20mm dia , 1.8 mm wall thickness and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 4 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: (i) Two runs of 4 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 4 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 20mm dia , 1.8 mm wall thickness wiil be measured as a one unit. (ii) Proper colour coding is to be followed as per IS Specification. (iii) Test certificates of cables to be submitted before commencement of work/ claiming for payment. (iv) wiring shall be concealed/ on surface with rigid PVC conduit medium grade as per site requirement. (v) Electric Wiring test sheet before and after completion of wiring to be submitted before claiming payment

M&L Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, connected to galvanized iron wire 4mm dia as earth lead by means of bolts,nuts and washers of GI up to test point,earh lead wire of size 4.0 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3 of SSR Part I, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI medium grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified. Note: The rate quoted include cost of 7.5 metre earthing wire with protection pipe.

Disconnecting and taking down existing tamper proof electric meter single phase, Re-assembling and refixing to the same /other location alongwith replacement of meter fixing box made out of thermoplastic grey colour with transparent cover, cable entry cover, hinged flap, protection cover including cable entry integrated elastic membrane suitable to accomodated two single phase KWH meter and fixing meter box to flush wall and making connection with proper thimbles, good disturbed surfaces, refixing seals and wires of the fixing the existing meter in meter box complete all as specified and directed. Note : Any damage caused to old serviceable meter while opening/refixing the same shall be make good/replace with new meter by contractor without claiming any extra cost on this account.

Exavation over areas, not exceeding 1.5m deep and getting out any type of soil complete all as specified & directed.

Excavation over areas, exceeding 1.5m deep but not exceeding 3.0m and getting out any type of soil complete all as specified & directed.

M&L Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundation laying poles, stay assembly and laying of GI pipe/LT/HT cables in any type of soil and getting out, complete all as specified.

M&L Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and as directed.

M&L Removal of excavated material (soil) to a distance not exc 50m and depositing where directed at a level not exceeding 1.5mtr above starting point complete all as specified and directed

M&L for LT underground cable XLPE and PVC insulated, armoured heavy duty electric cable shreathed, with aluminium conductor, 1100 volts grade, cross-sectional area 10 sqmm 4 core ISI marked as per IS : 7098 (Part-1) complete all as specified

S&F LT outdoor cable and terminal joint heat shrinkable complete suitable for aluminium conductor cable of cross sectional area 10 Sq mm , 4 core, 1100 Volt grade complete all as specified

M & L GI pipe light grade 40 mm bore with all fittings for cable protection fixed to walls/ poles or laid in trenches, under road/ under culvert/ under path/ under floor /on wall etc with fixing clamps, nuts bolts etc all as specified.

Supplying and laying in trenches clear sand for cushining under ground cable 8 cm below and 15 cm above complete in level all as specified

M & L Sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

Cutting and existing steel tubing for alteration or addition including screwing existing steel tubing to form connection/branch pipe etc for 50mm bore pipes complete all as specified and directed.

Supplying and laying GI pipe medium grade of size 50mm bore in trenches/on wall including all fittings complete all as specified

Supplying and laying GI pipe medium grade of size 25mm bore in trenches/on wall including all fittings complete all as specified

Supplying and laying GI pipe medium grade of size 20mm bore in trenches/on wall including all fittings complete all as specified

M&L construction of valve chamber of size 70 cm x 70 cm x 70 cm with PCC base foundation of thich 15 cm and the wall with PCC hollow blocks with necessary internal plaster of thickness 15 cm complete with chamber cover made up of 3.13 mm thick black sheet hinged both ends including necessary locking arrangements and fixing the same with angle iron frame of size 40 x 40 x 6 mm thick and all steel strutures to be painted with one coat of primer over one coat of black bitumen paint all as specified and directed.

S&F gun metal gate valves with iron wheel head, screwed both ends for iron pipe ISI marked as per IS-778 of size 50 mm bore complete all as specified

S&F Bell multi music type 230 Volts complete all as specified

Supply & Fix Exhaust fan AC sinlge phase 230/240 volts of size 300 mm sweep, 1350 RPM , power consumption not more than 70 watt including accessories blade set ,MS frame, copper wound fan motor , louver set, 4 nos 10 x 75 mm long fastners to fixed the same with existing wall including connecting to ceiling rose with 3 core 0.5 sqmm flexible copper wire all as required or directed.

Supply & Fix fan regulator electronic flush socket type stepped (rotary type) with 5 steps speed control complete all as required or directed.

Supply & Fix in replacement sheet metal powder coated vertical double door triple pole and neutral (VTPN) distribution system for MCB provision, 415 V, 50 Hz AC supply 4 way fitted with two cover with copper bus bar rated 200 amps neutral link, earth bar and din rail complete all as required or directed.

Supply & Fix inverter type LED fitting 1 x 20W, including LED tube 4' long having bipin holder, connector blosk, driver etc 230 Volts, duly prewired and electrical connections upto ceiling rose using PVC insulated overall sheathed flexible copper conductor cable of size 0.5 Sq mm 03 core complete all as required or directed.

Supply & Fix LED bulkhead fittings luminaires with opal diffuser including (LED lamp type 10W LED 6000K) lamp holder etc. complete all as required or directed.

Supply & Fix inverter type LED lamp 9 Watt 230 Volts complete all as required or directed.

Supply & Fix in replacement ceiling fan AC single phase 230/240 volts of size 1200 mm sweep complete type BEE 5 star rated VLDC rated complete with blade set ,down rod, copper wound fan motor , canopy set, shackle kit etc including connecting to ceiling rose with 3 core 0.5 sqmm flexible copper wire all as required or directed . Note: Old retrieved fans shall be deposited to MES store yard by contractor

Supply & fixing bus bar chamber of size 60cmx40cmx30cm fabricated out of 2mm thick CRCA sheet with three side closed and front side opening with locking arrangement including fixing 04 Nos of aluminium bus bar 200 Amps fixed on hygroscopic insulators 1100 Volts graded and fixing 01 Nos 04 pole MCCB 125 Amps 25 KA as incomer duly covered with CRCA sheet connecting MCCB to busbar using aluminium strip of suitable size complete all as specified or directed.

Supply, laying & testing cable XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured, electric power cable (heavy duty) 1100 Volts graded with stranded aluminium conductor of size 16 Sq mm 04 core complete all as required or directed.

S&F gun metal gate valves with iron wheel head, screwed both ends for iron pipe ISI marked as per IS-778 of size 20 mm bore complete all as specified

Notes : The Schedule of Credit amount shall be deducted from the total of this schedule(BoQ) to arrive at Contract Sum.

INDERJIT SINGH

SATISH AND CO

KULBHUSHAN AGGARWAL

Standard engineers

Abrol construction co

pardeep singh marwaha

Ashoka Engineers

kailu construction co