Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹28.0 LAccepted-AOC | ₹28.0 L Quoted ₹28.8 L | L1 | Accepted-AOC Accepted due to lowest rate quoted |
| 2 | L2₹29.6 LRejected-Finance | ₹29.6 L | L2 | Rejected-Finance Rejected due to highest rate quoted |
| 3 | L3₹31.5 LRejected-Finance | ₹31.5 L | L3 | Rejected-Finance Rejected due to highest rate quoted |
| 4 | L4₹32.3 LRejected-Finance | ₹32.3 L | L4 | Rejected-Finance Rejected due to highest rate quoted |
| 5 | L5₹33.2 LRejected-Finance NOT FOUND | ₹33.2 L | L5 | Rejected-Finance Rejected due to highest rate quoted |
| Sl No | Description | Qty | Unit | KISHAN SINGH AND CO L2 | shiv shanker enterprises L5 | Phogat Builders L4 | Shiv Shakti Builders L1 | PRAGATI BUILDERS L3 |
|---|---|---|---|---|---|---|---|---|
| 1.00 | Taking down cement plaster on brick walls & concrete surfaces & the like including raking out joints, hacking for key, scrubbing down with water etc., any description, including removal of rubbish outside MoD land, complete all as specified and directed. | 2,350 | Sqm | 12 ₹28,200 | 15 ₹35,250 | 10 ₹23,500 | 5 ₹11,750 | 10 ₹23,500 |
| 2.00 | M&L Rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:4) finished fair and even without using extra cement, complete all as specified and directed. | 1,000 | Sqm | 140 ₹1.4 L | 175 ₹1.8 L | 130 ₹1.3 L | 100 ₹1 L | 100 ₹1 L |
| 3.00 | M&L Rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement, complete all as specified and directed. | 800 | Sqm | 130 ₹1.0 L | 170 ₹1.4 L | 120 ₹96,000 | 90 ₹72,000 | 100 ₹80,000 |
| 4.00 | M&L Rendering 10 mm thick in cement mortar (1:3), as on concrete surfaces (such as top & sides of chajjas, beams, balcony ceiling etc.) finished even and smooth without using extra cement, complete all as specified and directed. | 550 | Sqm | 120 ₹66,000 | 170 ₹93,500 | 120 ₹66,000 | 100 ₹55,000 | 100 ₹55,000 |
| 5.00 | M&L for 3mm thick white wall putty on new/old surfaces of walls & making the surfaces fair and smooth complete all as specified and as directed by Engr-in-charge. | 800 | Sqm | 30 ₹24,000 | 13 ₹10,400 | 35 ₹28,000 | 50 ₹40,000 | 15 ₹12,000 |
| 6.00 | M&L for providing 3mm thick wall care putty on ceiling before applying oil bound distemper and making the surface uniform all as specified and directed | 550 | Sqm | 20 ₹11,000 | 13 ₹7,150 | 35 ₹19,250 | 50 ₹27,500 | 15 ₹8,250 |
| 7.00 | Demolition of un-reinforced concrete on roofs, floors (other than ground floors), beams/ chajjas and similar suspended work | 28 | Cum | 100 ₹2,800 | 220 ₹6,160 | 100 ₹2,800 | 100 ₹2,800 | 100 ₹2,800 |
| 8.00 | M & L for cement concrete in Type B1 1:2:4 (20mm gradede aggregate) for coping in chajja, balcony as specified and as directed. | 3 | Cum | 5,000 ₹15,000 | 4,500 ₹13,500 | 5,000 ₹15,000 | 3,500 ₹10,500 | 3,500 ₹10,500 |
| 9.00 | M&L for 50 mm thick PCC (1:2:4) type B-0 (Using 12.50mm graded stone aggregate) as in roof padding complete all as specified & as directed. | 500 | Sqm | 140 ₹70,000 | 245 ₹1.2 L | 180 ₹90,000 | 120 ₹60,000 | 200 ₹1 L |
| 10.00 | M&L for 15 mm thick plaster in cement mortar (1:4) mixed with water proofing compound on roof slabs, chajja finished even and smooth (without using extra cement) after cleaning of roof surfaces with wire brushes complete all as specified.
Notes : WPC shall be measured and paid seperately. | 520 | Sqm | 140 ₹72,800 | 180 ₹93,600 | 220 ₹1.1 L | 300 ₹1.6 L | 200 ₹1.0 L |
Updated dates
Tender Value
₹45 L
EMD Value
₹90,000
Closing Date
27 Nov 2025, 6:00 pmClosed
GE (AF) GURGAON
GE (AF) GURGAON
REPAIR TO FACIA PLASTER CHAJJA DOOR WINDOW AND OTHER MISC WORKS AT AF STN RAJOKRI UNDER GE (AF) GURGAON
2025_MES_737788_1
GE/GUR-/NIT-82/2025-26
Open Tender
Civil Works
240 days
GE (AF) GURGAON
Please refer Tender documents.
8 documents required · 8 mandatory
₹500
GE (AF) GURGAON
₹90,000
1 Jan 2026
30 Oct 2025
29 Nov 2025
30 Oct 2025
27 Nov 2025
13 Nov 2025
Amount
Taking down cement plaster on brick walls & concrete surfaces & the like including raking out joints, hacking for key, scrubbing down with water etc., any description, including removal of rubbish outside MoD land, complete all as specified and directed.
M&L Rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:4) finished fair and even without using extra cement, complete all as specified and directed.
M&L Rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement, complete all as specified and directed.
M&L Rendering 10 mm thick in cement mortar (1:3), as on concrete surfaces (such as top & sides of chajjas, beams, balcony ceiling etc.) finished even and smooth without using extra cement, complete all as specified and directed.
M&L for 3mm thick white wall putty on new/old surfaces of walls & making the surfaces fair and smooth complete all as specified and as directed by Engr-in-charge.
M&L for providing 3mm thick wall care putty on ceiling before applying oil bound distemper and making the surface uniform all as specified and directed
Demolition of un-reinforced concrete on roofs, floors (other than ground floors), beams/ chajjas and similar suspended work
M & L for cement concrete in Type B1 1:2:4 (20mm gradede aggregate) for coping in chajja, balcony as specified and as directed.
M&L for 50 mm thick PCC (1:2:4) type B-0 (Using 12.50mm graded stone aggregate) as in roof padding complete all as specified & as directed.
M&L for 15 mm thick plaster in cement mortar (1:4) mixed with water proofing compound on roof slabs, chajja finished even and smooth (without using extra cement) after cleaning of roof surfaces with wire brushes complete all as specified. Notes : WPC shall be measured and paid seperately.
Taking down existing water proofing treatment on the roof, cleaning with wire brush etc. and removing debris outside MD land all as specified and directed.
M&L for water proofing treatment with APP (Atactic Polypropylene) modified polymeric membrane over roof consisting of cleaning of concrete or plaster surface of roof & parapet walls and applying evenly a bitumen primer confirming to IS 3488 @ 0.40 Kg per sqm followed by a tack coat @ 1.2 kg per sqm using 85/25 grade industrial hot blow bitumen over it laid with APP modified polymeric water proofing membrane minimum weight 3.6 kg/sqm reinforced with non woven polyester fabric (weight not less than 160 grams per sqm) unrolled and bonded to substrata with logitudinal and end laps 100 mm as per manufacturer's instructions complete all as specified.
Demolition of reinforced cement concrete of any description and in any position not other wise specifically provided for complete all as directed.
M&L for Reinforced Cement Concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in in chajjas complete as specified and as directed.
S&F TMT reinforcement bars 10mm dia and over including all cutting bending binding cranking placing & binding with MS wire (ann ealed) not less than 0.9mm dia, complete.
all as item No 37 above but but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders
Material and labour, Gunniting to existing RCC Chajja, facia, parapet, beams, landings and similar RCC members after removing all loose concrete & preparations of surface, application of derusting chemical such as Dr Fixit Rust Remover or equivalent, welding additional bars/welded steel wire fabric if found necessary, priming reinforcement bars with a coat of zinc primer of coating not less than 40 micron, provision of bonding agent with bonding material like Dr Fixit bonding agent and repair to external RCC structure with slurry light and steel/ply form work and shortcrete concrete of mixed 1:3:1 (one part of cement, three part of coarse sand and one part of 10mm and down aggregate) of minimum 50mm thick incl plastering 5 mm thick in CM mortar 1:3 all as specified in IS 9012-1978 (all priming and bonding epoxy based paint shall be of Dr Fixit epoxy zinc primer or equivalent) etc complete all as specified and directed, as below:- Note(s) : 1. The rates include for necessary formwork and scafolding etc. 2. Reinforcement and welded steel wire fabric will be measured and paid separately.
Supplying and fabricating and placing in position of new TMT bars of any dia by welding or inserting by drilling holes and embeded in epoxy grout bonding agent of hilti or equivalent for all existing reinforcement repair works in any position wherever necessary complete all as specified and as directed by Engineer-in-charge. Note: The lap provided shall be 15 cm on either side of bar which has lost its sectional area all as specified and as directed
Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick rough finished inflat surface complete all as specified
Supply only liquid water proofing compound
M&L for preparation of newly plastered or unplastered/undecorated surfaces as of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.
M&L for preparation of newly plastered or unplastered/undecorated surfaces of ceiling and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.
M&L for preparation of newly plastered surfaces of wall and applying two coats of exterior emulsion paint over a coat of primer complete all as specified and as directed.
M&L Preparation of newly plastered surfaces of wall and applying two coat of Cement Base Paint of approved colour and shade by accepting officers over and including a coat of alkali resistant primer as per manufacturers instructions complete all as specified and directed by Engineer-in-Charge
M&L for preparation(complete removal of existing treatment) of old decorated external wall/ceiling surface of existing treatment by scrapping with Trucare Wall Sander : L-01/H-01 (having mechanical vaccum mechanism) having RPM not less than 1500, sand pad of 80 grit having dia of 7"/9" to make the surface free from dust, loose paint etc or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and applying Two coats of wheather proofing exterior acrylic emulsion paint over priming coat premium quality on wall/ceiling surface including applying 2mm thick wall care putty over disturbed surface during preparation of any reason, sand papering thus make surface smooth upto 4th storey buildings complete all as specified and directed. Note : (a) Stage for Preparation of surfaces shall be got approved from Engg-In-Charge before applying the finishes. (b) Material shall be procured from manufacturer and work shall be got executed through authorised applicator.
M&L for preparation of old surfaces of walls by washing rubbing down and stopping of surface and applying one coats of cement base paint complete all as specified and directed. Make of Cement Base paint : SNOWCEM/ASIANAINTS/DUROCEM /BERGER
Taking down shutters of any description not exceeding 1 Sq. m each, from chowkhat, complete all as specified
Taking down shutters of any description exceeding 1 Sq. m but not exceeding 2 Sq. m each, from chowkhat, complete all as specified
Taking down Chowkhats with shutters without taking of shutter from the frame of any description not exceeding 1.50 Sq. m each, complete all as specified
Taking down Chowkhats with shutters without taking of shutter from the frame of any description exceeding 1.50 Sq. m but not exceeding 4.00 Sq. m each, and making good the disturbed Surface in CM 1:4 & finished with similar specification as exists, complete all as specified
S&F Pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with and including back filling with PCC (1:3:6), type C-0, complete as specified and as directed.
S&F Pressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with and including back filling PCC (1:3:6), type C-0, complete as specified.
S&F 35 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamferesd or rounded, fitted with cut and mitred beads for securing glass etc., for windows and ventilators, etc are provided with stiles and rails as specified in SSR Pt I Section 8, clause 8.24 (b)complete all as specified and directed
S&F flush shutters 30 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and as directed.
S&F for Factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded coloured PVC ’C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of single side prelaminated PVC sheet to be fitted in the MS frame welded/ sealed into the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying and fixing in the frame at site as per specification complete all as specified and as directed by Engineer-in-Charge.
S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet & reinforced with MS square tube and fixing in opening as specification & drawing, complete all as specified and directed.
S&F powder coated anodized aluminum frame for partition, doors, windows, ventilations with one or more rebates including joining cleat for fixing etc. complete all as specified.
S&F powder coated anodized aluminum door shutters, aluminum section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing handles 2 Nos in each door,100 mm long hinges (3 Nos), anodized aluminum snap beading screws etc. complete all as specified.
S&F powder coated Anodised aluminium window and ventilator shutters, fixed/side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified.
S&F Powder coated aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge.
S&F Mild steel butt hinges medium weight, cold rolled, 100 mm, ISI marked, complete all as specified.
S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete.
S&F 200 mm aluminium anodized, barrel tower bolts of extruded section.
S&F 150mm size aluminum handle fabricated, 'D' type, anodized ISI marked complete all as specified and directed.
S&F 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy complete.
S&F in repair 300mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy complete.
S&F 150 mm long, Aluminum anodised floor door stopper alloy body and tounge, anodised, with hard drawn steel spring fixed in floor in repairs complete as specified and as directed.
S&F in repair 150 mm long, Aluminum anodised floor door stopper alloy body and tounge, anodised, with hard drawn steel spring fixed in floor in repairs complete as specified and as directed.
S&F in repair aluminium (Die cast) body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified.
S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete as specified and as directed.
S &F in repairs MS Butt hinges medium weight cold rolled & fixed 100mm long complete all as specified and as directed
S & F in repairs Aluminium anodized barrel tower bolts of extruded section 200mm complete all as specified and as directed
S & F in repairs Aluminium anodized barrel tower bolts of extruded section 150mm complete all as specified and as directed
S & F in repairs Aluminium anodized barrel tower bolts of extruded section 100mm complete all as specified and as directed
S & F in repairs Aluminium anodized handles cast type 150mm long complete all as specified and as directed
S & F in repairs Aluminium anodized handles cast type 100mm long complete all as specified and as directed
Supply & fix in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished
S&F in repairs 19 mm dia Aluminium curtain rod with powder coated along with ornamental attachment at both ends and one set of ornamental decorative MS clamps to fixed to walls complete all as specified and directed.
S&F door seal bottom with aluminium plate and rubber insulation 42'' x 1.5'' complete all as specified and as directed.
Resecuring or easing and adjusting without taking down shutter from the frame & re-fixing builders hardware as required including removal of unserviceable screws etc. not exceeding 1 Sq.m each, complete all as specified and directed by Engineer - in -Charge.
Resecuring or easing and adjusting without taking down shutter from the frame & re-fixing builders hardware as required including removal of unserviceable screws etc. area exc 1 Sq.m but not exc 2 Sq.m each, complete all as specified and directed by Engineer - in -Charge
Taking down easing adjusting of old wooden shutters of anyn description exc. 1 sqm but n.exc 2 sqm each and refixing in same opening after tiling work complete all as specified and as directed.
S & F Mild steel Angles, bars, flats etc., as in supports for stiffening of fencing, wall ties, hold fasts, clamps and similar small articles confirming to Fe 290 Gde-E-165 complete all as specified and directed
M & L for PCC (1:3:6) type C-1 (using 20 mm graded stone aggregate) as in padding, coping, bed plates, hold fast blocks, etc., including formwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.
Taking up or down steel tubing and connections 15mm dia pipes including cleaning for refixing or removal to store complete all as specified and as directed.
Taking up or down steel tubing and connections 20mm dia pipes including cleaning for refixing or removal to store complete all as specified and as directed.
S & F 15 mm bore Galvanized Steel tubes, medium grade with all fittings for water supply pipes etc., laid in trenches/fixed on walls.
S & F 20 mm bore Galvanized Steel tubes, medium grade with all fittings for water supply pipes etc., laid in trenches/fixed on walls.
Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, including removal of rubbish outside MoD land complete all as specified.
Demolition of brickwork built in cement mortar including all quoins, arches, pillars etc complete all as directed
M&L for brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 all as specified and as directed
M&L Brick work with sub class 'B' Bricks, straight or curved on plan to any radius as in half brick thick wall in CM 1:4 complete all as specified and directed by Engineer - in - Charge .
Dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the permises complete all as specified and as directed
M&L for non skid ceramic tiles 7 to 8 mm thick (square/rectangle) area of each tile exc 0.06sqm but not exc 0.18 sqm, in floors and scantling etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tile complete all as specified and as directed.
M&L for nonskid coloured ceramic tiles 7mm thick area of each tiles exeeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed neat cemet slury and pointed in coloured cement to match complete all as specified and as directed. (Notes : Screed bed measured and paid separately)
M&L for Coloured Vitrified Ceramic tiles 9-10 mm thick (Square/rectangular) of Light Shade , polished, area of each tile not exceeding 0.36 sqm, fixed in floor etc over set and jointed in neat cement slurry and pointed in coloured cement to match with coloured tiles complete all as specified.
M & L for glazed ceramic coloured tiles of size 450X 350X 7mm/ 600x300x7 mm thick as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match of tiles, complete all as specified and directed.
Demolition of stone slabs and tiles of any description or thickness in floors/walls, aprons etc laid bedded and pointed in any mortar.
M&L 20-25mm thick machine cut kota stone slab as in flooring, steps of stair(treads), over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the sahde of the slab including rubbing and polishing incl complete all as specified and as directed.
M&L 20-25 mm thick machine kota stone slab as in skirting/dado, riser of steps, laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.
M&L for Granite stone slab flooring 20 mm thick any colour/shade machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, rounding edges as required to be fixed gate pillar, door, windows cladding/flooring and openings, cooking platform etc. complete all as specified and as directed.
M&L for screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:6) for bedding of tiles complete all as specified.
M&L for 10 mm thick rendering in cement motar (1:4) on vertical surface for bracking of tiles etc of tiles complete all as specified.
M&L for screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:6) for bedding of tiles complete all as specified.
M&L for 15 mm thick rendering in cement motar (1:4) on vertical surface for bracking of tiles etc of tiles complete all as specified.
Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15cm thickness (below or above ground level).all as specified and directed.
M&L for 25mm thick plain cement concrete type B-1 (1:2:4) using 20mm gradedstone aggregate as in sub base all as specified and directed.
M&L for 40mm thick plain cement concrete type B-1 (1:2:4) using 20mm gradedstone aggregate as in sub base all as specified and directed.
M & L 75 mm thick, plain cement concrete 1:3:6, type C-2, using 40 mm graded mechanically crushed stone aggregates, laid in 1:20 slope as in plinth protection finished even and smooth without using extra cement, complete all as specified and as directed.
M&L for 100 mm thick Cement concrete type C1, 1:3:6 (using 40 mm graded aggregate) in foothpaths and hard standing finish even and fair without using extra cement complete all as specified and directed.
S&F for Factory made machine pressed Chequered cement concrete colour tiles 30 cm X 30 cm X22 mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors , over 20 mm thick screed bed in CM 1 :4 complete all as specified and as directed.
S&F in for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-35 Grade complete all as specified and directed.
M&L for Sand (M Sand) filling under interlocking tiles or in foundations, spread and levelled including watering and consolidation complete.
M&L for PCC 1:2:4 Type B-1 (using 20mm stone crushed agg.) as in rounded or chamfered on edges, copping etc in any description all as specified and as directed
S&F in repairs WC squatting pan “Orissa Pattern” of size 580 x 440mm white with integral foot rest (excluding flushing cistern & flush pipe) including connection to trap and to flush pipes etc and cement concrete bedding complete all as specified in SSR and including S&F trap set complete all as specified and directed.
S&F in repair Vitreous china wash down water closet pan, pedestal pattern (EWC) white, including seat cover , fixing bolts connection to trap & to flush pipe complete all as directed
S&F in repairs PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and incl ball valve float & handle, waste pipe & brackets complete set complete all as specified and directed.
S&F in repairs concealed stop cock type CP with long shank cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 15mm bore. complete all as specified and directed.
S&F in repairs stop cock/angle cock with long shank cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 15mm bore. complete all as specified and directed.
S&F in repair Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm125gms). Complete all as specified and as directed.
S&F in repairs bib tap, cast copper alloy with capstan head, CP fancy type with long body shank, screwed down with high pressure screwed for iron pipe & fixed 15mm bore, complete all as specified and directed.
S&F in repair pillar tap 15mm size cast copper alloy chromium plated fancy type screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipes.
S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect complete all as specified and directed.
Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittinges, heads, shoes, bends, swan-necks etc as specified and directed
S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed.
S & F 110 mm bore PVC (SWR) bends with/without door of any radius complete all as specified & directed.
S & F 110 mm bore PVC (SWR) junctionsingle, (single T), equal or unequal with/without door of any radius complete all as specified & directed.
S & F 110 mm bore PVC (SWR) Vent cowl complete all as specified & directed
S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed.
S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified & directed.
S & F 75 mm bore PVC (SWR) junction single, (single T), equal or unequal with/without door of any radius complete all as specified & directed.
S/F In repairs for removal of old PVC/cast iron floor trap incl wall crossing pipe and fixed with new outlet 75mm pvc (swr) floor trap/ multi trap with stainless steel grating and new wall crossing and filling with pcc 1:2:4 with water proofing compound including matchng with existed tile and joining with outer pipe line with solvent all as specified and directed by Engg in Charge.
Dismantling water tanks Capacity of tank exc 250 & n. exc 500 ltrs removing complete all as specified and as directed
Dismantling water tanks Capacity of tank exc 500 & n. exc 1000 ltrs removing complete all as specified and as directed
Supply and fixing rotational moulded polyethylene three layered water storage tanks 500 litres capacity (cylindrical,vertical with closed top) hoisted and fixed in position all as specified and as directed.
Supply and fixing rotational moulded polyethylene three layered water storage tanks 1000 ltrs capacity (cylindrical,vertical with closed top) hoisted and fixed in position all as specified and as directed.
S & F in repair for Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, Bore dia of pipe in 20 mm, etc complete all as specifed and directed.
S&F in repairs 20mm dia gun metal gate valve, with iron wheel head, screwed both ends for iron pipes complete all as specified and as directed.
Removal of bushes , shurbs and vegetation by top of the roof and surface of bldg all as specified and directed by Engr-in-Charge
Dismantling of wrought iron of mild steel work of any description in any position not otherwise specifically provided for all as specified.
Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165
S&F steel work as in tubular, rafters, purlins, posts and similar work (round/sqare/rectangular shape of pipes as approved by Engr-in-charge ) trusses of semi circle/ curved shape up to height 6 mtr including post special shaped washers etc complete incl necessary nut bolts wind ties and gusset plates etc using ERW or induction butt welded tubes conformining to IS 1161-1998 garde St-240 all as specified and as directed
S & F Rolled Mild Steel Plates (plain or Chequered) channels, square cut or notched, forming holes, without any attachment confirming to Fe 410-S complete all as specified.
Dismantling galvalume sheet (corrugated ,semi corrugated etc) in roof coverings incl ridges etc complete.
M&L for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and as directed.
M & L for preparation of new painted surfaces of wood and wood based materials of any description not other wise described over 10 cm width or girth and applying Two coat of synthetic enamel paint over a pink primer coat complete all as specified and directed
M&L Preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamelled paint over one coat of red oxide primer.
S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple including necessary beading complete all as specified.
S&F for 4.8/5.0 mm thick sheet glass ordinary quality and glazing each pane n exc 0.50 Sqm fixed with neoprene rubber gasket in aluminium frame work complete all as specified.
Hacking out old broken glass (any thickness size, quality or description) from wooden/ steel frames, glazed with putty or fixed with wooden beads/ metal pins complete all as specified and as directed.
S & F 4mm thick Sheet glass ordinary quality and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane, complete all as specified.
S & F 4.8/5 mm thick frosted glass ordinary quality and glazing not exceeding 0.5 Sqm fixed with neoprene rubber gasket in aluminium frame work complete all as specified.
S&F in repairs, stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to steel frames with tinned tacks, or galvanized wire staples, or fixed to wooden frames with first class hard wood bead, complete all as specified and directed.
Dismantling of boarding, any descreption, fixed in any position with nails all as specified and directed
S&F 18/19mm thick Particle board, exterior grade prelaminated both sides with decorative choice lamination, fixed with nails/ screw screws to timber frame work including liping work teak wood beading 6mm thick comple all as specified and directed
S&F in extruded brass handle fabricated type 75mm size and complete all as specified and directed (Make : Hettich, Ebco, Prime or equivalent)
S&F in repair Continuous (Piano) hinges SS, bright finish width of flaps 40mm complete all as specified and as directed
Supply and fix in repairs Magnetic closer of suitable size for kitchen/bedroom cupboards fixed with screws complete all as specified and directed
Supply and fix in repairs stainless steel telescopic ball bearing channel, zinc plated finish for drawer including necessary fittings up to length of 600mm fixed with screws complete all as specified and directed.
S&F in repair brass knobs 35-40mm dia fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed
KISHAN SINGH AND CO (BID ID -3478982)
PRAGATI BUILDERS (BID ID -3484075)
Phogat Builders (BID ID -3484150)
shiv shanker enterprises (BID ID -3484069)
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.16 MB
TenderDocuments82.pdf
Tender Documents • 0.51 MB
BOQ_826121.xls
BOQ • 13.43 MB
Download all tender documents and submit your bid