Repair/replacement of joinery and certain other works at OTM Accn under Zone B at Mil Stn Gaya

Amount

Taking down chowkat or frame with shutter (without taking off shutters from the frames) area not exceeding 1.5 Sq mtr each.

Taking down chowkat or frame with shutter (without taking off shutters from the frames) area exceeding 1.5 Sq mtr but not exceeding 4 Sq mtr each

Taking down Shutter of any description area exc. 1 sqm and not exc . 2 sqm each

Dismantling structural steel work including doors, gates, grills but excluding framed truss etc complete.

M&L for second class hardwood plain, solid, straight chowkat and frame, wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joint complete.

M&L for 35mm thick IInd class hard wood plain framed panel shutter (two panels or more) with lock rails and panel of 9mm thick B.W.P. commercial ply or 12mm veneered particle board with commercial veering on both faces. The size of rail and style as per I.S. 1003(Part-I)2001 ,complete all as specified and directed.

M&L for 35mm thick second class hardwood glazed and skelton door shutters (Three panels) open rebated and prepared to receive glass / gauge etc edges of framing plain chamfered or rounded with cut and mitred beads for securing glass/gauges etc with sash bars size of members of shutter as specified in SSR Part-I section 8, clause 8.24 (a) complete.

M&L for 35 mm thick Flush shutters, solid core construction, with block board core plywood face panels on both side, commercial type on both sides including 5 mm thick edging/beading on exposed to view on sides & top complete.

S&F 5 mm thick and 18/19 mm width 2nd class hard wood decorative edging/beading on exposed to view on sides & top complete all as specified and directed.

Taking down re-fixing Shutters of any description but exc 1 sq. m and n exc 2 sq. m each in same opening including easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc. Renewal of builder's hardware articles, if specially ordered, shall be paid for at 'supplied only' rates.

S & F solid PVC frame of size 50 mm x 47 mm made out of 5 mm single side prelam PVC sheet & edges will be printed to match with prelam sheet rein forced with MS square tube etc.

S&F factory made solid panel PVC door shutter 30mm (Style) consisting of frame made out of M.S tubes for top and bottom rails M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheets to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame

S&F 125 mm long Stainless steel butt hinges with steel hinge pin etc.

S&F 200mm long aluminium anodised barrel tower bolt and 12 mm dia fixed

S&F 150 mm long aluminium anodised barrel tower bolt and 12 mm dia fixed

S&F 150mm long aluminium anodised handle cast type and fixed D Type

S&F 125mm long aluminium anodised handle cast type and fixed D Type

S&F alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified.

S&F 100mm long butt hinges medium weight cold rolled mild steel and fixed

S&F 75 mm long Stainless steel butt hinges medium weight and fixed Make : Prayag

S & F in repair 300mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate complete.

S & F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanised wire staples (to be fixed upto four storey of bldgs) complete.

S & F in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanised wire staples (to be fixed upto four storey of bldgs) complete.

S&F framed work such as grills, gratings and holdfasts etc with ends of bars shouldered and or reiverted or forged into spikes, framed guard bars and similar work, conforming to Fe- 290-0 (Gde-E-165)

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in a square n exc 0.5 Sq m in each pane (to be fixed upto four storey of bldgs)

S&F 4mm thick figured glass, pin head type and glazing with oil putty in a square n exc 0.5 Sq m in each pane (to be fixed upto four storey of bldgs)

Hacking out old broken glass(any thickness, size, quality or description) from wooden/steel frames, glazed with putty or fixed with beads.

M & L for two coats of synthetic enamel paint over new wooden surfaces of any description not otherwise described over 10cm in width or grith over one coat of pink primer including preparation of surfaces complete.

M&L two coat of syntetic enamel paint over new steel surface of any description over 10cm in width or grith not otherwise described over one coat red oxide primer incl preparation of surfaces complete.

Refixing repair work of existing defective aluminium door, window, ventileter with and incuding necessary fitting with and including making good as per site requirment as directed by Engr-in-charge.

S&F Powder coated aluminium frame/shutters for doors, windows, ventilators sliding/openable etc icluding joining cleat for fixing, locking arrangement, rubber beading, screws etc complete all as specified. Make : JINDAL/HINDALCO/INDALCO. Note : (i) Glazing and wire mesh shall be measured and paid separetely. (ii) Item shall be paid as per weight of aluminium section. (iii) The rate quoted shall be inclusive of the cost of neoprene beading, glazing pin, screws and powder coated fittings such as locking arrangement etc as required, which shall not be measured for arriving the weight (iv) The rate shall also be inclusive of complete packing with silicon gel around contacting surfaces of aluminium work, and including matching the existing.

Supply only rubber beading for repairing of existing door shutter

S&F sheet glass 5mm thick pin headed/froasted and glazing with clips in squaire . exc 0.50 sq m in each pane

S&F framed work as in doors or gates of angle or other section with gussest plates, rails, braces, etc, complete drilled for fixing of steel sheeting or other covering doors etc, to be prepared for hanging and sliding with and including either hooks and hinges or steel hanging door fittings and fixing complete confirming to gde Fe 290 (Gde E-165)

M&L for pressed steel door frame size 105 mm x 60 mm made of 1.25 mm thick sheet including necessary fixing lugs, hinges, lock strike plate etc. complete, all as specified.

M&L for pressed steel door frame size 165 mm x 60 mm made of 1.25 mm thick sheet including necessary fixing lugs, hinges, lock strike plate etc., complete, all as specified.

M&L for providing PCC 1:3:6, type C-0 (using 12.50 mm graded stone aggregate) as in filling of pressed steel door frame and holdfasts including necessary formwork etc.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L Brick work using old size bricks with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as spd.

Taking down cement plaster any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for rendering on fair faces of brick work or concrete surface of wall 15mm thick in CM 1:6 and to be finished even and smooth with out using extra cement complete all as specified and directed

S&F in repair steel locking bolts with mild steel electrogalvanised plate and bright bolt not less than 10 mm dia, 100 mm size

S&F in repair Aluminium body ISI marked Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed Make: Hardwyn/Marshal

S&F in repair 100 mm long mortice latch with two levers (vertical type), mild steel body complete all as specified and directed.

S&F double legged door stopper of aluminium alloy with rubber all as specified and directed by Engr-in-charge.

M & L for preparation of newly plastered surfaces of walls and applying two coat of distempering over a coat of primer complete.

S & F radiant door bottom sealing strip guard for doors complete all as all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets all as specified and directed.

S & F of Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete.

S&F 4 mm thick HPSC (High Pressure steam cured) pre-primed textured designer board, water resistant, be placed in the grid system all as specified and directed by the Engineer-in-Charge. Make Everest/Armstrong

S & F in repairs of 4 mm thick HPSC (High Pressure steam cured) pre-primed textured designer board, water resistant, be placed in the grid system all as specified and directed by the Engineer-in-Charge. Make : Everest/Armstrong

M/s Subham Traders (BID ID -3096154)

M/S ASHOK KUMAR (BID ID -3097835)

M/S NARAYAN & SHARMA (BID ID -3097765)

M/S PANCHAM RAI SONS (BID ID -3096628)

SINGHAL ENTERPRISES (BID ID -3098100)

MS HARI MOHAN GUPTA (BID ID -3096423)

BEHL ENGINEERS AND TRADERS (BID ID -3096532)

M/S SHYAM BIHARI PRASAD YADVENDU (BID ID -3097603)

M/S ABHAY KUMAR AND BROTHERS (BID ID -3097376)