Repair/ Renovation of 05 Nos. Ty-II Qtrs and 04 Nos. Ty-I Qtrs of STS Department inside the campus of STS Workshop, Lucknow under Sub Division No.I, NACD, APWD, Mayabunder i/c IEI.

Amount

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge:

All kinds of soil

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.

All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources).

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 40 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form work for :

Foundations, footings, bases for columns

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

35 mm thick

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing.

30 mm thick plain PVC door shutters

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).

6 mm thick Cement fiber board as per IS: 14862

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler i) 110 mm

Bend 87.5° i) 110 mm bend

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :

New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade :

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Applying priming coat:

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Melamine polishing on wood work (one or more coat).

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.

With cement mortar 1:4 (1 cement : 4 fine sand)

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area 3 sq. metres and below

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :

Of area 3 sq. metres and below

Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead :

Of sectional area 40 square centimetres and above

Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in:

Channels, angles, tees and flats

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:

Asbestos Cement sheet

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead :

75 to 80 mm dia pipe

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :

15 mm to 40 mm nominal bore

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink without drain board i) 610x510 mm bowl depth 200 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe i) 32 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

25 mm nominal dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work

25 mm dia nominal bore

50 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :

50 to 80 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25 mm nominal bore

50 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length i) 15 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

25 mm nominal bore

50 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately).

Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer-in-charge.

Supplying and applying bituminous solution primer on roof and / or wall surface at 0.24 litre per sqm.

Grading roof for water proofing treatment with

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and fixing Stainless Steel grating of approved quality as per direction of Engineer-in-charge.

Circular Grating of 100mm dia.

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : (a) 150 mm

Providing and fixing unplastisized G.I. pipe clips of approved design to unplastiside sized PVC sanitary waste pipes by means of 50x50x50mm hard wood plugs screwed with MS screws of required length including cutting brick work and fixing with a cement mortar 1:4 and making good the wall etc complete.

110 mm dia pipe.

75 mm dia pipe.

Extra for providing and fixing wind ties of 40x6mm flat aluminium section with necessary screws etc.

Providing and fixing CPVC Ball Valve of approved quality High or low pressure with plastic floats complete.

25 mm nominal bore

Providing and fixing CPVC Union in CPVC pipe including cutting and threading the pipe and making long screws etc. complete

25 mm nominal bore

Providing and fixing CPVC Tank Nipple (Tank Connector pipe) for water tank pipe, fittings of approved quality and colour.

25 mm nominal bore

Providing and fixing precoated galvalume (PPGL) steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, with aluminium Zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd.

Plain Valley 900mm

Providing and fixing glass panes with aluminium beading i/c glass putty in steel windows all complete

4.00mm thick glass panes

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion.

Bend With Door i) 110 mm.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fastners of required dia & length (hold fast lugs or dash fastner shall be paid for separately) :

Superior Hardwood of Cat-II A

Providing and laying hollow block cement concrete block walling 200mm thick consisting of hollow block of size 400mm x 200mm x 200mm of mix 1:3:6 (1 cement; 3 coarse sand; 6 graded stone aggregate 10mm nominal size) having a crushing strength of 3.5 N/Sqm at 28 days as per IS:2185 (Part-I) 1979 laid in cement mortar 1:6 (1 cement; 6 coarse sand) upto floor five level.

Providing and fixing 35 mm thick glazed shutters for windows with Superior Hard wood category-II(A) as per IS: 401 using 7.5 kg/Sqm (4 mm thick) glass panes including ISI marked stainless steel butt hinges using of required size with necessary screw etc. complete as per direction by Engineer-in-charge.

Providing and fixing 18 mm thick, 150 mm wide pelmet of HDF Boards, nickel plated M.S. pipe 20 mm dia ( heavy type ) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm long and rawl plugs 50 mm long etc. all complete

Providing and fixing soil, waste and vent pipes with UPVC pipe conforming to IS:13592 Type B including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion. (i) Single socketed pipes.

75 mm dia pipe.

Providing and fixing UPVC moulded single equal plain junction of required degree with access door insersion rubber washer 3mm thick, bolts and nuts complete for UPVC soil pipes conforming to IS:13592 Type B including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion.

Providing and fixing UPVC moulded plain bend of required degree for UPVC soil pipes conforming to IS:13592 Type B including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion.

Providing and fixing UPVC moulded door bend of required degree with access door insertion rubber washer 3mm thick, bolts and nuts complete for UPVC soil pipes conforming to IS:13592 Type B including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion.

Providing and fixing UPVC terminal guard.

Providing and fixing UPVC moulded self cleaning trap design with screw down or hinged grating with arm complete including cost cutting and making good the walls and floors Grating shall be stainless steel of 100mm dia.

100mm inlet and 75mm outlet.

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : (i/c arm pipe)

100 mm diameter (Jaguar or equivalent)

Providing and fixing C.P. brass stop cock (concealed) standard design and of approved quality conforming to IS:8931 :

15 mm nominal bore (Jaguar or equivalent).

Providing and fixing C.P. brass bib cock of standard design and approved quality conforming to IS:8931 :

15 mm nominal bore (Jaguar or equivalent).

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15mm nominal bore (Jaguar or equivalent).

Providing and fixing C.P. brass long nose bib cock with wall flange of approved quality conforming to IS standard and weighing not less than 810 gms.

15mm nominal bore (Jaguar or equivalent).

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. (Jaguar or equivalent).

Extra length for providing connection flush pipe connecting with orissa pattern WC pan 32mm dia.

Providing and fixing PVC Low Level flushing cistern (Single Flush) with manually controlled device (handle lever) of Parryware Model No. E82971C with all fittings and fixtures complete.

10 Ltrs capacity white.

Providing and fixing wall Hung frosted glass shelf with wall brackets complete as per the direction of EIC.

Of size 450mm (L) x 150mm (W)

Providing and fixing C.P. towel ring as approved by Engineer-in-charge with concealed fittings arrangement of approved quality and colour (make of Jaguar or equivalent brand) Size of minimum 250mm or above.

Providing and fixing C.P. Soap Dish Holder having length of 138mm , breadth 102mm, height of 75mm width concealed fittings arrangements , Weighing not less than 106 gms of approved quality (Of Jaguar, Hindware , Parryware or equivalent). Size of minimum 250mm or above.

Providing and fixing C.P. Brass towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.

600MM long towel rail (Jaguar or equivalent)

Providing and fixing aluminium hooks and eyes. a)150 mm.

Dismantling of eaves or facia board (WPC/Timber) along with its nut bolts for eaves height upto 10 metres including stacking the material within 50 metres lead.

Dismantling of pvc door with frame & shutter,including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. all complete as per the direction of EIC.

Dismantling of wash basin fitted with C.I. brackets including stacking of useful materials near the site and disposal of unserviceable materials within 50 meter lead.

Providing and fixing eaves or facia baord with 19mm thick WPC board 30 cm wide including fixing with GI nut and bolts etc. complete.

Providing and Fixing steel Ladder of overall length 6.00mtr & 0.50mtr width (outer to outer) consisting of 50dia GI Pipes as the vertical rail members & 32mm dia GI pipes as the intermediate rungs spaced @ 300c/c i/c fixing the same to the steel staging in a required position and painted with black anti corrosive bitumastic paint of all complete as per enclosed detailed drawing sketch & direction of EIC.

Providing and Fixing steel Ladder of overall Length 3.00mtr & 0.50mtr width (outer to outer) consisting of 40dia GI Pipes as the vertical rail members & 32mm dia GI pipes as the intermediate rungs spaced @ 300c/c i/c fixing the same to the steel staging in a required position and painted with black anti corrosive bitumastic paint of all complete as per enclosed detailed drawing sketch & direction of EIC.

Construction of 5.80m ht Steel Staging with double Platforms each of Size 3.00X1.60m whole unit provided with 06Nos of RCC Short Column base (300mm x 300mm size) with foundation footing for each and foundation depth of 1.20 Mtr with short column raised to 150mm above G.L and erecting Pre- fabricated staging over the short column base by means of base bearing plates & Foundation bolts. etc complete., Including Pre-Fabrication of 01 nos of Steel Staging with double platforms each of size 3.00m Length & 1.60m width & each platform welded over with 20Gauge thick GI Sheet and staging frame consisting of 06nos of 65dia GI Pipes in vertical posts and 50mm dia GI Pipes in horizontal tie members & 40mm dia GI Pipes in cross bracings provided as required in all of its four sides & 50dia GI Pipe in outer frame of each top platforms with 32mm dia GI pipes in its intermediate spaced @ 150c/c , complete unit made out of GI pipes and painted with black anti corrosive bitumastic paint of all complete as per enclosed detailed drawing sketch & direction of EIC.

Construction of 2.80m ht Steel Staging of Platform Size 1.60X1.60m provided with 04Nos of RCC Short Column (250mm x 250mm size) with foundation footing for each and foundation depth of 1.10 Mtr with short column raised to 150mm above G.L and erecting Pre- fabricated staging over the short column base by means of base bearing plates & Foundation bolts. etc complete., Including Pre-Fabrication of 01 nos of Steel Staging of top platform size 1.60m Length & 1.60m width, Top platform welded over with 20Gauge thick GI Sheet and staging frame of 04nos of 50dia GI Pipes in vertical posts and 32mm dia GI Pipes horizontal tie members & cross bracings provided as required in all of its four sides & 50dia GI Pipe in outer frame of Top platform with 32mm dia GI pipes in its intermediate spaced @ 150c/c , complete unit made out of GI pipes and painted with black anti corrosive bitumastic paint all complete as per enclosed detailed drawing sketch & direction of EIC.

Removal of old damaged window glass panes from the steel windows i/c racking out the old putty, rusted nails/screws etc for the purpose of fixing of new glass panes.

Providing and fixing pre-painted galvalume (PPGL) steel profile sheets AZ-150 of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd. or equalavent (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with aluminium zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling / self tapping aluminium screws (Xylan) of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvalume (PPGL) steel profile sheets accessories 0.50 mm (+0.05 %) total coated thickness, with aluminium Zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd.

Ridges plain (500 - 600mm)

Gutter (600 mm over all girth)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

Group B

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required.

100 mm X 100 mm X 60 mm deep

180 mm X 100 mm X 60 mm deep

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required.

5/6 amps switch

3 pin 5/6 A socket outlet

TV antenna socket outlet

Supplying and fixing metal box of 150mm X 75mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch, connections, painting etc. as required.

Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type switch, connections, painting etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying and fixing PVC batten/ angle holder including connections etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

12 way , Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and re-filling as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Supplying of LED Adore 10 W 2 star rating B22 CDL lamp similar to Make: Havells Cat No. LHLDEUEEML8R010 6500K or its equalent to ISI standard.

Supplying of Batten for LED tubes equivalent to HAVELLS REGALBATTENT8UPTO1X22WSSBSWH including 20W LED Tube lamp equivalent to HAVELLS CRYSTAL GLASS LED TUBE LIGHT (Double side connection) Cat No. CRYSTALT81213DSTL20WLED865SGLASS complete or its equivalent to ISI standard.

Supplying of 10W LED Bulk Head environment friendly, ultra modern, energy saving, surface mounted, decorative hexogen bulk head Back-lit LED luminaire comprising of high brightness LEDs equivalent to Havells HEXA 10W - IP66 Cat No.HEXAFT10WLED857SSYMBOPC etc. or its equivalent to ISI standard.

Supplying of Domestic exhaust fan 300mm sweep equivalent to Orient Electric 300mm Air Flow complete or its equivalent to ISI standard.

Supplying of Energy efficiency BLDC ceiling fan of white in colour with remote control of 1200mm sweep, suitable for operation on 230 volts, single phase, 50Hz, AC supply including 30cm long down rod etc. as required equivalent to Havells Efficiencia Neo (BLDC 26 W) or its equivalent to ISI specifications.

Providing and erection of single phase metering box made out of SMC of size 250 x 250 x 155 with hinged cover and locking arrangements, viewing glass etc. as required similar to Sintex Model No. GSMB 2525.

Ananta Sadhukhan

ST.GEORGE CONSTRUCTIONS