INTERIOR FIT OUT WORKS IN THE OFFICE SPACE OF THE ORIENTAL INSURANCE COMPANY LTD., BLOCK 4, PLATE A, GF 4TH FLOOR, COMMERCIAL COMPLEX, EAST KIDWAI NAG

Grand Total DSR + Non DSR (including of GST) 198042120.00

S.NO. DSR / MR DESCRIPTION QUANTITY UNIT RATE

DSR ITEM NON DSR ITEM

1 CONCRETE WORK

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth

4.1.8 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) 351.85 Cum 6326.05 2225825.6

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up

to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) 100 Sqm 1018.05 101805

2.02 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 100 Sqm 86.45 8645

3 FINISHING WORK

3.01 13.4 12 mm cement plaster of mix :

13.4.1 1:4 (1 cement: 4 coarse sand) 100 Sqm 307.25 30725

3.02 13.60 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :

13.60.1 Two or more coats on new work 2200 Sqm 137.85 303270

3.03 13.61 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

13.61.1 Two or more coats on new work 50 Sqm 131.45 6572.5

4 WATERPROOFING WORK

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like

consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in

recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3

4.01 22.3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical 50 Sqm 774.25 38712.5

and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of

400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7

CEMENT CONCRETE HARDENER : 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement

4.02 11.4 hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening 50 Sqm 855.9 42795

compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but

excluding the cost of nosing of steps etc. complete.

5 DOOR,WINDOW & PARTITION

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold

fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood 1.6 Cum 131576.95 210523.12

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board

5.02 9.21 construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and

face veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 80 Sqm 2015.75 161260

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of

door shutter to be measured).

Providing and fixing Stainless steel satin finish SS 304 grade Tower Bolts SS screws for wooden doors of approved make and model all

5.04 MR complete as per the directions of Engineer-in-charge 16 Each 572.00 9152

Providing and fixing Stainless steel satin finish SS 304 grade Handles with SS screws for wooden doors of approved make and model

5.05 MR all complete as per the directions of Engineer-in-charge 32 Each 2065.00 66080

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564,

5.06 9.83 embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. 16 Each 1025.65 16410.4

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and

5.07 9.53 embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal 128 Each 194.35 24876.8

Supply and installation of Aluminium Framed Glass Partitionfor Access and Cabin System for minimal frame, room dividing

solutions.Single glazed mullion free demountable glass partition using Toughened/ Laminated glass in proprietary natural

anodised/Black aluminium sections ALT 50 of size 50mm x 30mm with Concealed sealing (No visible Gaskets/Seals) with acoustic

rating of Minimum 32 db with third party test certificate. The profile will have Carpert Groove at the Bottom on both sides for

accomodating max. 8mm carpets. THe Glass to be fixed with help of Proprietary Stability GRIPPER Clamp to have a stable system. It

5.08 MR should consists of intermediate slim junction profiles for Glass to Glass vertical joints, 90 Degree L Junction and T Junction profiles 450 Sqm 5976.00 2689200

suitably to be used as per room configuration designs.No VISIBLE Clip Lines to provide clutter free view at both side of section. The

Glass to be Offset mounted towards outer edge leading to minimum aluminium frame on one side. Optional Profile Bottom Seal pair for

additional accoustic. Glass thickness - 10( LSG).shall be included in the product.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and

fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing

5.09 21.18 required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). 300 Sqm 4540.70 1362210

Providing and fixing SS tubular handle bar 32 mm outer dia, 3.0 mm thick & 900 mm long with SS screws etc .complete as per direction

of Engineer-in-Charge.

MR Powder coated minimum thickness 50 micron aluminium tubular handle bar 260 Each 5742.00 1492920

Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to reproduce Sand-blasting effect

on glass with customised designs, thickness of 2 mil (0.05mm) without adhesive & 3mil (0.8)with adhesive having minimum tensile

strength of 3.5 pound/inch at 73 F(0.6 kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7 kg/cm) on

5.11 MR Acrylic, Glass Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to 15yrs (indoors) must be endorsed by 3M India 400 Sqm 2742.00 1096800

Limited Architectural Market Department. Contractors payment wouldn't be released until & unless he/she produces orginal warranty

certificate from the manufacturer.

6 PARTITION WORK

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on

wooden /steel frame work, complete as per direction of Engineer-in

9.140.1 12mm thick MDF Board 6500 Sqm 1084.6 7049900

Providing and fixing metal system up to ceiling height, which includes frame work made of special section power pressed/ roll form G.I.

sheet with zinc coating of 120 GSM, consisting of Boral U track 52mm wide having equal flanges of 30mm and 0.55mm thick (Base

metal thickness) fastened to the floor slab and ceiling soffit using rawl plugs with screw at 600mm centers, with first & last fixing point at

6.02 MR not greater than 50 mm from either end. Boral C studs 50mm wide having one flange of 34mm, other flange 36mm, lip size 6 mm and 3000 Sqm 876.00 2628000

0.55mm thick installed perpendicularly within the flanges of floor and ceiling channels located directly opposite to each other at not more

than 610mm centers. Maintain 5 to 10mm gap between C Stud and web of U Track.

7 FLOORING WORK

ENGINEERED WOODEN FLOORING Panel 1820 x 145 Total thickness 14 mm Numbers of panels per pack 6 Nested Lengths Max. 1

plank out of 6 m2 per pack 1,583 m2 Kg per pack 11,99 kg Toplayer PEFC controlled sources EN 13489 ± 3 mm Core board PEFC

controlled sources Spruce Backing layer PEFC controlled sources Wood Veneer 2 mm Tongue and groove Length Uniclic Width

Uniclic Multifit Domestic use Conditions in each pack 33 years Uniclic - Multifit connection Lifetime Commercial On request "Wood for

Life" Edge Protect + Provides a warranty on build-up of residue dirt along the edges due to maintenance over the years 10 years

"Wood for Life" Surface & Edge Protect + (lacquered products only) Provides a warranty on pollution of surface structure and a

warranty on build-up residue dirt along the edges due to maintenance over the years 10 years Surface layer Wood species Oak Origin

Europe Finishing UV cured Oiled finish 2 layers UV cured Lacquer Anti-scratch top coat 5 - 7 layers Natural variance Due to nature,

visual surface can deviate from samples Surface treatments cf catalogue/website Nature Marquant Vibrant General aspect of installed

EN 13489 Lipping - difference in height (mm) ≤ 0,20 difference in width (mm) ≤ 0,20 cupping lengthwise % ≤ 0,1 cupping in width % ≤

0,2 Dimensional stability ISO 24339 Cupping short side max % ≤ 0,30 Changes 30 - 85 % RH Cupping short side min % ≥ - 0,20 Open

joints short side (mm) ≤ 0,20 Open joints long side (mm) ≤ 0,30 Underfloor heating Suitable of special installation instructions.or its

FOR OPEN WORKSTATION AREAS CARPET :Providing and laying Floor Architecture Collection- Poured tiles of Yarn type Eco

Solution Q® Nylon ( Nylon 6 ) only; Multi-Level Pattern Loop, manufactured using solution dyeing process, Tiles of size 61 cms x 61

cms with Shaw Soil & stain resistance protective treatment ™ or equivalent containing properties of Stain Repel, Stain resist & Stain

Release , Anti , with Ecoworx® Tile- 100% PVC Free / 100% Bitumen Free/ 100% Recyclable - backing system with recycled content,

made from thermoplastic polyolefin compound with reinforcing layer high performance environments requiring modular flooring , having

tufted yarn weight of 542.5 gsm and average yarn density of 7385 oz/cu. yd. or more, Nominal total thickness 5.79 mm minimum,

7.02 MR Radiant Panel class1rated ( ASTM E648) ,NBS smoke < 450, Pill test -Passed, Texture Appearance Retention Rating of 3.5 for Severe 1200 Sqm 2577.00 3092400

Use, Anti Microbial Treatment-Passes (AATCC-174). CRI Green Label Plus certified for indoor air quality, including fixing/ installation

with Low/ Zero VOC content Adhesive. Impact Sound (ISO 10140-3) 20 dB & Sound absorption (ISO 354) 0.2 Class D.

Manufacturer to submit Test Report / Certificate stating meeting CRI's - Severe Use Rating and Acoustic properties and complying to

specification is mandatory. All Certificates to be provided before release or award of Contract.

FOR MEETING ROOM & BOARD ROOMS CARPET Providing and laying Living system Collection tiles of Yarn type Eco Solution Q®

Nylon ( Nylon 6 ) only; Multi-Level Pattern Loop, manufactured using solution dyeing process, Planks of size 23 cms x 91 cms with

Shaw Soil & stain resistance protective treatment ™ or equivalent containing properties of Stain Repel, Stain resist & Stain Release ,

Anti , with Ecoworx® Tile- 100% PVC Free / 100% Bitumen Free/ 100% Recyclable - backing system with recycled content, made from

thermoplastic polyolefin compound with reinforcing layer high performance environments requiring modular flooring , having tufted yarn

7.03 MR weight of 745 gsm and average yarn density of 8700 oz/cu. yd. or more, Nominal total thickness 6.65 mm minimum, Radiant Panel 400 Sqm 3564.00 1425600

class1rated ( ASTM E648) ,NBS smoke < 450, Pill test -Passed, Texture Appearance Retention Rating of 3.5 for Severe Use, Anti

Microbial Treatment-Passes (AATCC-174). CRI Green Label Plus certified for indoor air quality, including fixing/ installation with Low/

Zero VOC content Adhesive. Impact Sound (ISO 10140-3) 20 dB & Sound absorption (ISO 354) 0.2 Class D.

Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all

complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1

7.04 11.51 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with

pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the

Engineer-in-Charge.

11.51.1 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc. 250 Sqm 6095.5 1523875

Providing and laying machine cut, mirror polished, Italian Marble brass brass inlay stone flooring laid in required pattern in linear portion

of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement

7.05 11.51 mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry

admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed

by the Engineer-in-Charge.

11.51.1 18 mm thick Italian Marble stone slab in all colour and shade 10 Sqm 6095.5 60955

Providing & fixing of PANELS in patented round hole profile of size 146mm x 25mm x 3000mm(Min). IFS Terra decking are hybrid

composites with a wood plastic composite core made of 65% wood fiber, 30% High Density Polyethylene and 5% Additives and 360

degree capping of high performance polymer compound for high UV resistance and vibrant aesthetics produced using co extrusion

process.The Cladding panels should adhere to accelerated weather testing as per ASTM G154:2016,Cycle-1, Density of 1.3g/cum &

tensile strength >22Mpa . The panel should be compatible with no visible screw installation system using Novel Terra Powder coated

7.06 MR Steel Clips 110 Sqm 10280.00 1130800

The no visible screw installation process is then done using Novel terra Clips fixed over a framework constructed of Hollow Aluminium

Channels with Min 16 Gz with wood Infill installed parallely with centre to centre distance between each channel of not more than

450mm. The Decking can be finished with suitable aluminum finishing profiles.

Providing and fixing made in India Glass mosaic tiles at Floor & finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour,

design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with

7.07 MR the help of approved Adhesive AD HOC (2,7 kg) + Epoxy coloured grout FILLGEL PLUS UVR (3 kg) applied at the rate per sqm. The 90 Sqm 13843.00 1245870

rate is inclusive of all operation, material and required pattern

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than

0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4

7.08 11.41 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments

etc., complete.

Providing and laying Decorative vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption

less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1

7.09 11.41 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching

pigments etc., complete.

Providing and Fixing of 5+1 mm thick Click-N-Lock tiles with wear layer is of 0.5 mm, Stone Polymer composite and has an IXPE

Cushion backing of 1 mm ,100% Water & Termite proof, Scratch / Fire / UV resistant, a Recyclable Green product having WEL-

7.10 MR LOCK click system with suitable skirting. Classification of abrasion resistance ( Rubbing action of two abrading wheels of S-42 Type , 600 Sqm 3016.00 1809600

load Applied 500 grams, No. of Cycles 4,200).Design as approved by the Engineer/Architect"

Supply of 100 mm "DMC" Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish. Thichness 1.30 to 1.50 mm.

Designed to conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and Gasket.

8 FALSE CEILING WORK

Providing and fixing GI Plain 75mm wide x15mm deep panel upto 6mtr, shall be roll formed out of 0.5mm thick Powder Coated .The top

coat of panel shall be 60 micron polyester coated finish in approved colour. The panel shall be factory cut in up to 6Mtr OR required

length. Accessories Detail: Carrier: 63mm deep, made out of 0.6mm thick steel backed with enameled black paint having cut out to hold

8.01 MR on panel in a module of 75mm closed. The joint of two carriers shall be joined by means of carrier splices maintaining a module of 50 Sqm 3907.00 195350

75mm .4mm dia galvanized rod with special height adjustment butter fly clips made out of SS steel sheet. The edge profile G.I.shall be

matching with the panel.

Providing & Fixing of GI Clip in perforated Metal Ceiling System of 300x1200 mm module which includes providing and fixing wall angle

of size 20x20 mm made of 0.4 mm thick & 35 x 75 mm made of 0.5 mm pre painted steel along the perimeter of the room with help of

nylon sleeves and wooden screws at 300 mm centre to centre, suspending the main C carrier of size 10x50x10 mm made of G.I steel

0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and

main carrier bracket at 1200 mm c/c. Clip in profile main runner having height of 40 mm and width of 19 mm made of GI steel 0.5 mm

8(b) MR thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centres with help of suspension brackets & with L 116 Sqm 1919.00 222604

profile size of 24x24x0.40mm. Wherever the main C carrier and Clip in Profile have to join, C carrier and Clip in Profile connectors have

to be used, fixing with clip in tiles into Clip in Profile with : GI Metal Ceiling Clip in perforated (1.8mm dia) Beveled edge global white

color tiles of size 300x1200 made out of 0.5 mm thick Galvanized Sheet Tegular edge with 8 mm drop; and 20% perforation area with

1.8 mm dia holes and having NRC (Noise Reduction Coefficient) of 0.7, electro statically polyester powder coated of thickness 60

microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

To Supply & Install Custom made Vertical curve Polylam Blades Ceilings as per the design intent. The vertically curve baffle system

POLYLAM exhibiting space- delineating characteristics. The system comprises vertically curve baffle with 750-150mm deep curved

rafters manufactured out of 2.0mm Aluminium to provide wave effect. The module for fixing baffle shall be 150mm centres as per

design requirement. The carrier rails run perpendicular to the baffles axis and can be mounted with M6 threaded rods using technical

8.02 MR approved fasteners as per EN 13964 standards. The individual baffle lengths between 1200- 2400 mm can be selected. Baffles lengths 1000 Sqm 8834.00 8834000

less than 1500mm required two carrier rails mounted at the baffle ends. Baffle longer than 1500mm require additional carrier rails

mounted in the centre. Finish RAL Powder Coated.No Pre Coated products shall be accepted. The spacing of the grid angles is

according to the requirements of DIN 18168 and DIN EN 13964 and quality controlled to ISO 9001:2015 approved by SIS & LEED

certification by Indian Green Building council (IGBC).

Polylam system formed as an open metal ceiling with an open area of more than 50%. The multidirectional ceiling composed of

equilateral triangles 600mm modules with perfectly homogeneous aspect and the im-pression of a uniform assembly. The main blades

comprising 100mm height & 25 mm width interlocked polylams in Extruded aluminium 1.50mm thickness compensating tolerances in x

and y direction. The substructure consists of a form punched perforated profile [U1040] as a lateral grid which is suspended from the

ceil-ing with nonius adjustable upper and lower parts or with threaded rods using official approved dowel plugs. The grid profiles are to

be connected together at the ends by means of longitudinal connect-ors [U 1041] [screw fasteners]. The spacing of the grid profile is

according to the requirements of DIN EN 13964. On profiles angles, C-band raster as secondary profiles are bolted on by means of C

channel hanger bracket with M6 bolts. Only construction parts ap-proved by the manufacturer may be used. Provide necessary

supports, provisions as per the architects / PM’s Instructions. Toler-ances according to TAIM, DIN EN 13964 and quality controlled to

ISO 9001:2008 approved by TUV. Finish of ceiling is in wood Finish powder coated with mini-mum 60 microns paint thickness.

Providing & Installation of Baffle ceiling system comprises of 50 mm x 100 mm (50 mm width & 100 mm Height) U Shape panels in RAL

color finish. Panels shall be made of 0.5 mm thick galvanized steel after Powder-coated and length up to 4000 mm. Panel shall be high

corrosion resistance and good color stability. Centre to Centre panel gap will be 150 mm. Panels are fixed on to roll formed carriers 20

mm wide x 40 mm deep out of 0.80 mm G.I sheet Powder-coated color with cutouts to hold the panels in module of 50 mm at maximum

8.04 MR 1200 m c/c. Carriers are suspended from the roof or truss by 6 mm dia. galvanized steel wire rod hanger with special height adjustment 800 Sqm 3975.00 3180000

suspension clip at max. 1200 mm c/c. Hangers are fixed to the roof by ‘J’ hooks or ceiling brackets and nylon inserts. Panels are factory

cut in lengths up to maximum 4.0 m to suit site dimensions or shop drawings. Top cap and side cap are used to cover the edges of the

Supply & installationof fabric false ceiling / wall formed out with TRANSLUCENT Printed fabric coverings made out of polyester knitted

fabric coated with Polyurethane (PU). The TRANSLUCENT Printed fabric width of 2m, 3m, 4.1m &5.1m with weight of 200gm/m2,

thickness of 0, 3 mm. The appearance of fabric is matt, smooth and uniform with blanq color and light transmission of 50%. The tear

strength of fabric should be accordance to CH: 4,5daN; TR: 6,5 daN. The fire rating should be accordance to B-S1, d0. The fabric

should be humidity resistant and free of carcinogenic substances(CMR) or volatile organic Compounds (VOC’s). At labeling in

accordance with the French decree no. 2011- 321, Oeko-Tex standard100 certified. Fabric should be installed with approved

manufacturer guidelines. It comes with 10- year manufacturer guarantee. The installation of TRANSLUCENT Printed fabric should be

8.05 MR dry installation & done at room temperature using PVC, ABS Grippers. Clipso ceiling base to be made of MS or Wooden frame finishing 110 Sqm 16447.00 1809170

to a flush finish of tapered and square edges in desired design as per architect specification.Supply of LED Lights behind the Fabric

Wall/ False ceiling in modules/ PCB with recommended wattage as per manufacturer's standards to give an effect of ambient lighting.

LED spacing / Pitch should be atleast 73 -80mm with beam angle of 170 degree, Colour temperature shoud be as per design intent

3000K/4000K/6000K. Wattage of 8-10W/mtr. LED modules/ PCB should be positioned properly to provide an even light flow, casting

noshadows or dark spots. LED Driver Cost included.

Providing & fixing of panels - 1200mm*2400mm *20mm thickness, NRC = 0.90, Resistance to fire : REI 90 made out of mineral fibre.

Panels to be fixed on framework made out GI ( 0.60mm thick & 60 MM Width ) sections to form a section of 600mm x 600mm. Panels

8.06 MR to be fixed on the Slabs with a minimum of 50mm to 100mm void or gap with Galvanized screws of length 50 mm & Dia 4.5 mm.In case 125 Sqm 4609.00 576125

of islands - vertical shall be provided with metal section all 4 sides. In case of wall to wall, wall angle shall be provided towards the wall

or UD section shall be provided which shall be concealled as per the architects design.

Providing and fixing DINOC Film(fine wood,texture,leather finish), a flexible cast PVC with comply adhesive intended to cover all type of

the surfaces such as wall covering, fixture, ceiling, doors, interior applications. The substrate can be be gypsum board, ply wood, MDF

8.07 MR board, Aluminium, Stainless Steel, Mortar (with sealer coating). The thickness of the film is approx. 215 microns (film/adhesives), 650 Sqm 6537.00 4249050

cadmium free. The self adhesive would be permanent acrylic adhesive with comply performance and a liner of PE coated kraft paper.

The installation is to be done on a smooth, dust free putty surface that has a coat of oil based premier.

Supply & Install: Loop Type 2 system formed as an open metal ceiling with an open area of more than 50% and to the flare [5mm] of the

perforation pattern [RV-50-40] the ceiling has a three-dimensional visual effect and hides the insight into the plenum. Bypassing the

perforation, the S-shaped sides of the LOOP interlock both the long and front side joint with a non magnetic suspension, the elements

are installed with a circumferential 1 mm joint, thus compensating tolerances in x and y direction. The non-magnetic suspension system

effectuates a self-alignment of the elements [puzzle effect]. The module size 966x1115x1.0mm GMS is perforated with 60mm deep

drawn holes .The substructure consists of a form perforated L profile [U1040] as a lateral grid which is suspended from the ceiling with

nonius adjustable upper and lower parts or with threaded rods using official approved dowel plugs. The grid profiles are to be

connected together at the ends by means of longitudinal connectors [U 1041] [screw fasteners]. The spacing of the grid profile is

according to the requirements of DIN EN 13964. On profiles angles, C-band raster as secondary profiles are bolted on by means of C

channel hanger bracket with M6 bolts. Only construction parts approved by the manufacturer may be used. Provide necessary

supports, provisions as per the architects Instructions. Tolerances according to TAIM, DIN EN 13964 and quality controlled to ISO

9001:2008 approved by TUV.Finish of ceiling is in RAL 9016 white/ RAL 9006 Silver grey powder coated with minimum 60 microns

paint thickness.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size

25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash

fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required

length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at

8.09 12.45 the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26

mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel

with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm

thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs

at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter

channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered

and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers

covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also

including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all

complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) 2000 Sqm 1145.95 2291900

Providing & Fixing of GI MESH LAYIN metal ceiling System consisting of 600x600mm Lay in tiles of GI with Rhombus / Hexagonal

shape mesh to be laid on manufecturer T Grid 38 with 24 mm wide T - section flanges in white having rotary stitching on all T sections

i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38 mm and a load carrying capacity of 13.2 Kgs/M2.

8.10 MR Connection strength of cross tee to cross tee is 100 Kgs. Suspension system for manufecturer grid to be of manufecturer make.GI 33 Sqm 2807.00 92631

Mesh of size 600mmX600mm with Short way of opening (SWO) as 11.0mm & 12.6mm and Long way of opening (LWO) as 25.9mm &

30.5mm with an open area of 78.0% & 84.0% for Lattice Flat or Rhombic design (Termed as Rhombic #4 & #7 respectively). Mesh

available in factory coated finish.

Providing and Fixing and Installation of Trap Door of Single Leaf with all necessary hardwares as per Interior Design and the direction

of Ebgineer-in-charge

9 WALL FINISHES

Providing and fixing of 6 mm thick premium GRIHA rated Lacquered glass of approved color by Architect/ Client / Customer, fixed with

compatible neutral grade silicon on a perfectly levelled 12mm thick water proof marine plywood / MDF / Mineral fibre board which is

mounted on RCC wall/any other structure. Lacquered glass must be made industrially (using curtain coating process); opaque (if

viewed against a support wall), uniformly coated with PU lacquer (50 micron thick coating or more); panel to panel colour consistency

9.01 MR (measured by photo spectrometer); highly durable (passes hardness test for minimum 220 oscillations); humidity resistance (conforms 250 Sqm 5112.00 1278000

to BS EN 1036 1999 or equivalent) ; environmentally friendly having Low VOC (no lead, no arsenic, no copper, no formaldehyde),

low VOC content <100g/l. Silicone used should not react with lacquer coating (compatible neutral cure silicon)

Providing and fixing 4mm thick coir veneer board, ISI marked IS : 14842, plain lining with necessary screws, priming coat on unexposed

9.02 8.29 surface etc., complete. 50 Sqm 1549.45 77472.5

Providing and laying Decorative vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less

than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of

9.03 11.41 cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white

cement & matching pigments etc. complete.

Providing Installing & Fixing with specified adhesive by Neolith, a sintered Stone made up of granite minerals like quartz, fedspar with

required strength and hardness. Waterproof, Resistant to UV rays, scratches, lightweight and recyclable. Sheet size of 3250x1550 with

a 6 mm thickness. The colour shall be approved as per the choice of the architect and as per the theme of the project. The sheet shall

be in SILK FINISH with perfect linear reflection. The cost shall include cutting of the tile in different sizes -1200x600,1500x750.

Customised Wall Panel - Plain; designed(400mm X 600mm); Supply , Testing and Commisioning of maintainance free Moss Wall of

9.05 MR size 600 x 400 mm panel of natural light green color/ shade.The plant shall be for indoor use only and requires no Direct Sun Light or 25 Sqm 40000.00 1000000

Watering / Spraying of water.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density

9.06 9.127 protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of

approved quality.

Providing & fixing of panels - 1200mm*2400mm *20mm thickness, NRC = 0.90, Resistance to fire : REI 90 made out of mineral fibre.

Panels to be fixed on framework made out GI ( 0.60mm thick & 60 MM Width ) sections to form a section of 600mm x 600mm. Panels

9.07 MR to be fixed on the Slabs with a minimum of 50mm to 100mm void or gap with Galvanized screws of length 50 mm & Dia 4.5 mm.In case 300 Sqm 3907.00 1172100

of islands - vertical shall be provided with metal section all 4 sides. In case of wall to wall, wall angle shall be provided towards the wall

or UD section shall be provided which shall be concealled as per the architects design.

Providing & Fixing Vinyl Coated Wall covering as per approved make and pattern as approved by the client & architect.

Providing and fixing made in India H-UHPC Panels (Plain/Porous Finish) of different sizes with thickness of 10mm in all colour, design

with water absorption of less than 0.2%, compressive strength of <50Mpa ( N/mn2), Bending strength of 6.8Mpa(N/mn2) at finished

9.09 MR plain wall surface , fixing in customize design as per direction of Engineer-in- Charge. The H-UHPC Panels to be fixed on the wall 57 Sqm 6500.00 370500

surface with the help of approved Concrete based Adhesive + the joints to be grouted with Cement coloured grout. The rate is inclusive

of all operation, material and required pattern.

Providing and fixing of Ecoresin panel of sixe 1220mm x 2440mm with variety of inlay between panels of specified Gauge. The panels

are made from ecoresin sheet with engineered polyester resin with a thickness of 6.5/9.5 mm (+/- 5%)with a top/bottom finish as

sandstone finish. The product conforms to Class A impact rating in accordance with ANSI Z97.1-2004 at 1/8” thickness, has no

9.10 MR detectable VOC off-gassing as measured under ASTM standards D 5116 and D 6670, is Greenguard™ Indoor Air Quality certified and 8 Each 304000.00 2432000

has a minimum of 40% post-industrial recycle content certified by a recognized 3rd party certification group, such as Scientific

Certification Systems (SCS). The design of the product is based on specification & approval of Engineer-in-charge as per tender

Providing & fixing of straight Paneling for walls & Columns structures anchored in floor slab & celling, cladded with Acrylic Solid Surface

12mm thick sheets straight fabricated on a single face, finished in matte finish, pasted with industrial grade silicon on a robust substrate.

Substrate shall be with suitable MS box sections [Appx. 15 to 20 kg/ Sqm] as per structural requirement & duly painted with anti-rust red

9.11 MR oxide coating and covered with 12 mm thick water proof ply as per the design and dimensions approved. The proposal includes the 80 Sqm 14031.00 1122480

cost of preparing appropriate substrate surface over the civil structure provided, along with material cost & installation / fixing on straight

walls etc. FOR ALL WALL CLADDING, TABLE TOPS ETC. COMPLETE

Providing & supplying of Window Blinds as per the approved sample, DUETTE Single HONEYCOMB SHADES Easy rise operating

system and standard design option Original Non-woven honeycomb shades having soft fabric appearance and high energy-efficient

fabric with high tear strength constructed out of Anti static, resilent, colour fast & Sanitized Treat 100% spun bonded non-woven

polyester fiber & precision manufacture to form a hexagonally shaped duette pleat . Pleat dimension ¾”Honeycomb structure with

distinct air pocket for energy effeciency and increased insulation. Shadings are duotone, with neutral tone facing the exterior and color

facing the interior .Being a Low shading co-efficient will have following Comfort rating & solar optical properies. The HEADRAIL shall

measure 49.68 wide and 36.66mm deep & thick 1.27mm extruded from 6063 T6 alu. alloy & shall be powder coated to a smooth finish

with a thickness of 40 microns. All cords & cord holes shall be fully concealed inside the fabric structure. As each of the hexagonal cells

9.12 MR is formed individually, pleats operate independent of each other providing superior pleat retention & structure strength. INSTALLATION 30 Sqm 15253.00 457590

BRACKETS shall be of high tension spring steel suitable for overhead & wall mounting 30mm Duette Hartford mounting bracket.

POLYESTER CORD shall be 0.9mm in diameter & of woven hollow core. ENDCAP shall be molded acrylic color matched to the head &

bottom rails. BOTTOM RAIL shall be a single channel section, measuring 30mm wide and 12.5mm deep & thickness 1-1.2mm extruded

from 5005 H-16 alu. alloy & shall be powder coated with a smooth finish to a thickness of 15-25 microns. HOLD-DOWN BRACKET

(optional) shall be molded in clear acrylic. It incorporates a pin for engagement with the bottom rail end-cap. It shall be suitable for sill,

face or side facing. CORD.EQUILISER shall be injection molded from impact modified acrylic with a high flexural modulus.

Providing & supplying of Window Blinds as per the approved sample in required shade and style consisting, of Roller Blindscomprising

of optima screen Fabric comprising of 22% polyester, 78% PVC, Fabric weight 460-480G weight per sq m, Thickness 0.67 mm, Yarn

count 18-19/cm, having fire resistance standard – NFPA 701-89 small testing ISO-5659-2 .Thetear resistance should be complying to

ISO4674 & breaking resistance – ISO 5081. The DRIVE UNIT shall be of clutch forquick,easy

andsafeinstallation,moldedplasticwithsteelspringsupportandinserted intothe tubeend.Itshallbe drivenby a ball chain pulley with ball chain

and can be positioned at right side or left hand side of the Shade.The Shade whenlowering or raising, shall be automatically locked in

position upon release of the ball chain by means of a built in friction lock.Universal clutch for left and right hand operation.Chain Gear

Ratio of 1.75:1.The END PLUG shall be molded of plastic witha steel location pin.The plug shall be inserted into the tube end.(Opposite

9.13 MR to the Drive Unit) for ease of installation. TheSUPPORT BRACKETS shall be of coated steel & provided with covers and used in right 250 Sqm 2498.00 624500

hand or left handpositions differentiated by the acceptance of the of the rectangular drive unit support or the round idler plug pin.Can

beinstalled (a) On Face (b) Ceiling Mount (c) On Frame (d) in Recess. The Bracket should be protruding outside maximum

of80mm.The ROLLER TUBE shall be of extruded aluminum with 37mm internal diameter & skin thickness of 1mm and

shallincorporateakeywayintegral withthetubetoaccommodatethespline. The BOTTOM RAIL shall be a Flat Bottom made up of powder

coated steel. The BALLCHAINshall be 2mm diameter cord with 4.5mm diameter acetal balls molded co-axially toit on6mm

pitchtoformanendless ballchain.It is usedforraisingor loweringactionoftheshades.

Providing & supplying fabric venetian Window Blinds as per the approved sample, consisting of 3" vane size having head rail, rotator

rail and bottom rail made of aluminum alloy 6063-T6 PER ASTM B221 - 85 extruded profile, powder coated and provided in standard

natural white color. The rolling tube should be made up of aluminum alloy from extruded profile of 34 mm dia . The head rail dimensions

should be of suitable size according to the length of head rail and space available and finished with fabric cover matching with the

louver fabric .The cassette should conceal the working mechanism rotary-clutch. (White polycarbonate spring tempered rotary clutch

9.14 MR which raises), lower and tilts the blinds. White polycarbonate limit assemblies control vane over-rotation, located on either side of 100 Sqm 13178.00 1317800

individual blinds. The room darkening fabric of Blind should be of anti static polyester vanes which have facings between two sheer

layers (50 mm wide) to reduce glare. Sheer layers should be of white 100% knit polyester, the colors, textures and opacities as

approved. The fabric shall be made of spun- bonded 100% polyester fiber ( having Green guard certification ) treated with soil & dust

repellent requiring minimum regular interval cleaning.GREEN GUARD Gold certified for low-emitting products to maintain Indoor

environment. Upto 80% ultraviolet protection with vanes open and 90% with vanes closed. The shading to be operated by Easy rise

mechanism with a continuous cord loop operating system. All parts, components & hardware are in approved shade as per direction of

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm

thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI

wire etc. complete as per directions of Engineer-in-Charge.

WOODEN MOULDING- Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with

iron screws, plugs etc. complete MDF Finished 18X30 mm (base and height)

WOODEN MOULDING- Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with

iron screws, plugs etc. complete MDF Finished 20x50 mm (base and height)

WOODEN MOULDING- Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with

iron screws, plugs etc. complete MDF Finished 12x25mm (base and height)

10 Miscellaneous Work

Modular kitchen - Under counter storage cabinets:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and sufficient

number of drawers made of 18 mm thk. ISI Marked comm. ply , all ply to be laminated with 0.8 mm laminate.All shelves should be

supported on approved quality SS pins and shall be adjustable for different heights as per requirements.Shutters and drawers fascia

shall be at least 18mm thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters finished in high

10.01 MR gloss acrylic of approved. The cabinet boxes of floor units will be supported by 100mm height vertical adjustable legs which will be 36 Sqm 24752.00 891072

covered with PVC skirting in brushed aluminum finish attached by hardware of skirting. The unit shall be fixed to the floor/ wall/slab

using metal screws of appropriate size and rawl plugs. Only front face area of cabinets and skirting from floor to top of boxes shall be

considered for measurement and payment. Cabinet boxes size would be varies from 400X560X710MM to 1000X560X710MM (approx.)

and join together as per site requirements etc.

Modular Kitchen - Overhead storage wall units:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and sufficient

number of drawers made of 18 mm thk. ISI Marked comm. ply. All ply to be laminated with 0.8 mm laminate.All shelves should be

supported on approved quality SS pins and shall be adjustable for different heights as per requirements.Shutters and drawers fascia

10.02 MR shall be at least 18mm thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters finished in high 24 Sqm 17805.00 427320

gloss acrylic of approved. The unit shall be fixed to the floor/ wall/slab using metal screws of appropriate size and raw plugs. Only front

face area of cabinets and skirting from floor to top of boxes shall be considered for measurement and payment. Cabinet boxes size

would be varies from 400X560X710MM to 1000X560X710MM (approx.) and join together as per site requirements etc.

10.03 MR Providing and fixing of Innotech with metal sides and quadro channels 10 Each 3317.00 33170

10.04 MR Providing and fixing baskets 10 Each 3789.00 37890

Providing anti-viral,anti-bacterial,anti-mould and anti-odour coating (invisible and odourless) based on cutting edge technology

Premium Purity that creates self disinfecting surfaces for 365 days, works with the combination of light (natural or artificial). The coating

should be able to purify air and improve the indoor climate by decomposing VOC's-Nox,Sox,Carbon monoxide, Benzene etc. and also

be approved on surfaces with food contact. The solution should be implemented by trained professionals with electro-static sprayers. It

should decompose microbes like MRSA, CORONAVIRUS, SWINE FLU, E-COLI, EBOLA, SALMONELLA, ADENOVIRUS,

NOROVIRUS, INFLUENZA etc., and also be able to reduce contamination by decomposing microbes within minutes. In addition to this,

10.05 MR provide Eco-friendly salt and water based Electrochemically Activated water solution for daily cleaning that would be able to replace 2048 Sqm 846.00 1732608

majority of currently used chemicals and disinfectants for surface cleaning. SOP's for hygiene and cleaning for the premises with these

solutions to be made and staff trained in use of the daily cleaning and disinfection solution. The premises should show positive

comparitive ATP results for microbial and cleanliness levels .The coating should have successfully passed various EN tests for

relevant bacteria,viruses,mould and fungi. from various International laboratories and organizations (ECHA list, FDA compliant ,WHO

compliant,ISO, ) FSSAI, DIPP registered.

Company name "ORIENTAL INSURANCE CO" cut in SS brush 3d letter (SS304) of text ht. 600 and of deph 1.5" font to be cut to

sizes and directly installed on available base as per with approved SS fixtures, including necessary hardware, substructure, extra, as No. 75 8,903.00 667725.00

specified and directed by Engineer in charge. The letters shall be back lit.

10.07 MR Various Direction signages of exit and washroom identification with LED glow panel and proper fixture for installation and connection

10.08 MR Providing making and fixing in position custom made SS siganges of sizes 16"x5"as per Architectural drawings and instruction with

approved SS fixtures, approved base including necessary hardware, substructure extra complete as per detail drawing, as specified No. 75 890.00 66750.00

and directed by Engineer in charge

Canvas paintings (Oil/ Acrylic medium)

Concept Creation

Creating design and creation of Art work concept on given subject. With initial visit to site, preparation of various designs with different

material, providing the samples, layout for approval, improvisation in short listed creative’s and making of final layout for final production

11.01 MR by enlargement of drawing as per ratio of actual size, to prepare detailed working shop drawings (full scale) based on the Concept 25 Sqm 13067.00 326675

drawings/ Views/ site conditions, display of actual size dummy/ mock up fabricated in sun board with digital print for client approval

ART WORK EXECUTION

Towards the cost of doing canvas painting by qualified artist including frame and installation at site

12 Horticulture and Landscaping

12.01 MR Supply and Planting Draco plant having 6ft height complete. 5 Each 18486.00 92430

Supply and Planting Monstera plant having 3-4 ft height complete.

12.03 MR Supply and Planting Lolina plant having 2-3 ft height with Coco-peat, mud and manure complete. 25 Each 1849.00 46225

Supply and Planting Seaforthia Palm having ht. 90cm to 1.20 m with 6-8 suckers, well developed, fresh and healthy lush green leaves

from bottom to top complete.

Supply and Planting Rhapis Palm having ht. 90cm to 1.20 m with 15 to 18 equal suckers, well developed, full of fresh and healthy

leaves from bottom to top complete.

Supply of full soil fill conical shaped planters of specified volume and dimensions in stone finish or equivalent. planters to be

indigenously made by rotational moulding, with homogeneous recyclable, industrial grade polymer-resin mix, and textured surface.

12.06 MR planters should have an integrated water outlet hole & plug, single layered peel-proof construction, light weight, rust proof, uv stabilized,

anti-frost feature without any joints, and easy to clean. planter supplier must give 1 year warranty against any fading or cracking for

both indoor and outdoor use. green plant and laying is extra. potting instructions as per company catalogue.

Supply of double layered translucent backlit cylinderical shaped - hand carfted pattern planters of volume 18 ltr; approx. dimension

24(h)x18(d) in granite/ stone/ solid finish or equivalent. planters to be indigenously made by rotational moulding, with homogeneous

100% recyclable, industrial grade polymer-resin mix, with textured surface and stone match finishes. planters to have concealed shock

12.07 MR resistant back lighting system with secured supply wire and an integrated water outlet hole & plug, peel proof construction, asbestos 10 Each 13799.00 137990

free, light in weight, without any joints, rust proof, uv stabilized, anti-frost feature and easy to clean. planter supplier must give 1 year

warranty against any led, fading or cracking for indoor and outdoor use.

Supply of double layered translucent backlit cylinderical shaped - hand carfted pattern planters of volume 40 ltr; approx. dimension

40(h)x18.5(d) in granite/ stone/ solid finish or equivalent. planters to be indigenously made by rotational moulding, with homogeneous

100% recyclable, industrial grade polymer-resin mix, with textured surface and stone match finishes. planters to have concealed shock

12.08 MR resistant back lighting system with secured supply wire and an integrated water outlet hole & plug, peel proof construction, asbestos 10 Each 21812.00 218120

free, light in weight, without any joints, rust proof, uv stabilized, anti-frost feature and easy to clean. planter supplier must give 1 year

warranty against any led, fading or cracking for indoor and outdoor use.

GRAND TOTAL 75679673.92

GRAND TOTAL 75679673.92

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR VOL-2 QUANTIT

S.NO. DESCRIPTION UNIT RATE TOTAL AMOUNT TOTAL AMOUNT

S.NO. DESCRIPTION UNIT RATE TOTAL AMOUNT TOTAL AMOUNT

2021 DSR ( INR ) N0N -DSR ( INR )

Supply, Installation, Testing and Commisioning of SINGLE LEVER CONCEALED BASIN

MR 1 MIXER (WALL MOUNTED) WITH SPOUT (COMPOSITE ONE PIECE BODY) Model No. SIG- EACH 3 20196.00 60588.00

CHR-41233 or equivalnt

Supply, Installation, Testing and Commisioning of TABLE TOP BASIN, SIZE: 630X460X130

MM Model No. XQS-WHT-43901 or equivalent

Supply, Installation, Testing and Commisioing of suitable compatible WASTE COUPLING

MR 3 32MM- FULL THREAD- WITH CERAMIC CAP-*130MM HEIGHT *65MM CERAMIC CAP EACH 3 1220.00 3660.00

Model No. ZAS-WHT-9002 or equivalent

Supply, Installation, Testing and Commisioing of BOTTLE TRAP (WITH INTERNAL

PARTITION) 32mm SIZE WITH 300mm & 190mm LONG WALL CONNECTION PIPES &

WALL FLANGE (Model No. ALDCHR-769L300X190 or equivalent)

Supply, Installation, Testing and Commisiong of RIMLESS, BLIND INSTALLATION WALL

MR 5 HUNG WC WITH UF SOFT CLOSE SLIM SEAT COVER, HINGES AND ACCESSORIES EACH 3 12098.00 36294.00

SET, SIZE: 375X520X400 MM SLSWHT- 6953BIUFSM

Supply, Installation, Testing and Commisiong of PNEUMATIC CONTROL PLATE ACPWHT-

Supply, Installation, Testing and Commisiong of ANGULAR STOP COCK WITH WALL

FLANGE SIG-CHR-41053

Supply, Installation, Testing and Commisiong of CONCEALED STOP COCK WITH

ADJUSTABLE WITH WALL FLANGE 15mm SIG-CHR-41083

Supply, Installation, Testing and Commisiong of HAND SHOWER (HEALTH FAUCET) WITH

8mm DIA 1.2 METER LONG FLEXIBLE TUBE

Supply, HOOK ALD-CHR-573

Installation, Testing andor Commisiong

equivalent of PNEUMATIC SINGLE PIECE SLIM

CONCEALED CISTERN BODY WITH INSTALLATION

17.10 KIT & “S-TYPE”

Providing DRAIN

and fixing PIPE Steel

Stainless CONNECTION SET FOR

A ISI 304 (18/8) WALL

kitchen sinkHUNG

as WC (WITHOUT

per IS:13983 with C.I. brackets and stainless steel plug 40 mm,

11 including painting of fittings and brackets, cutting and making good

the walls wherever required :

17.10.1 Kitchen Sink with Drain Board

17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings

17.28.2 Flexible pipe

17.31 Providing and fixing 600x450 mm beveled edge mirror of superior Each 3 1411.15 4233.45

glass (of approved quality) complete with 6 mm thick hard board

13 ground fixed to wooden cleats with C.P. brass screws and washers

17.34 Providing and fixing toilet paper holder

18.53 Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved

quality conforming to IS : 8931

18.53.1 15 mm nominal bore Each 10 500.35 5003.50

17.61 Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast

(spun) iron pipes and making good the same with cement concrete 1:3:6 (1 cement: 3 coarse

17.61.1 sand:mm

dia stone aggregate 12.5 mm nominal size) including necessary plaster and M 5 615.70 3078.50

18.76 Cutting holes upto 30 X 30 cm in walls including making good the same.

18.76.1 With common burnt clay F.P.S. (non modular) bricks Each 3 362.40 1087.20

18.78 Making chases upto 7.5 X 7.5 cm in walls including making good and finishing with matching M 5 171.80 859.00

surface after housing G.I. pipe etc.

18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for

hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the

19 pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step

CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

18.7.2 20mm nominal outer dia pipes M 50 325.10 16255.00

18.7.3 25mm nominal outer dia pipes M 20 408.55 8171.00

18.7.4 32mm nominal outer dia pipes M 20 500.95 10019.00

18.7.5 40mm nominal outer dia pipes M 5 674.35 3371.75

18.7.6 50mm nominal outer dia pipes M 5 927.00 4635.00

18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for

hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe

with clamps at 1.00 m spacing.

Concealed work including cutting chases and making good the walls etc.

18.8.1 15mm nominal outer dia pipes M 93.1 441.15 41063.50

18.8.2 20mm nominal outer dia pipes M 50 513.75 25687.50

18.8.3 25mm nominal outer dia pipes M 5 626.05 3130.25

18.8.4 32mm nominal outer dia pipes M 5 712.75 3563.75

18.51 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS

21 standards and weighing not less than 690 gms.

18.51.1 15 mm nominal bore Each 5 708.40 3542.00

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for

soil, waste, and vent, Type-B as per IS : 13592 suitable for rubber ring joints, including all

neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or

without doors), reducers, WC connectors, couplers, expansion joints / bellows, cowels,

clamps, rubber rings, clean outs etc. fixing at wall/ ceiling/ floor level supported by clamp &

hangers etc. in concealed / inside duct / under floor & basement ceiling / external work etc.

including chase cutting as required, excavation and back filling in all kind of soils, suspended

from floor under false ceiling or embedding the pipes laid under floors / building in 75 mm.

alround 1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) including cost of shuttering for proper completion of the work, breaking and

making good the walls and floors etc. after pipes have been duly laid and tested. The rubber

ring shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with nuts, washers etc on

50x50x5 mm slotted angle. The cost will include all support arrangements. The work includes

commissioning of all pipes lines as per drawings and specifications and as directed by engg-in-

charge at site.

MR 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) metre 100.00 368.00 36800.00

MR 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) metre 20.00 368.00 7360.00

Providing, fixing, jointing and testing in position ISI marked (IS:4985) UPVC pipes of min 6

Kg/ Sqcm rating with fitting for waste pipe from fixtures to floor trap including reduces,

23 enlarger, socket, couplers, bends, tees etc including fixing at wall/ ceiling level supported by

clamp & hangers etc. cutting holes in wall/ floors/ slabs and making good the same with

cement concrete 1:2:4 complete as required.

Providing & fixing UPVC Floor trap of self cleansing design with stainless steel grating

complete in all respects.

Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser 3883.00

Extra for providing & fixing 125 mm dia C.P. grating in place of C.I. grating over floor traps. 7920.00

Providing & fixing of SS Floor Cleanout, round or square with rubber seal and flat round cover

with screws and other required fitting complete as required. 6314.00

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

SNO. M - 2018) DESCRIPTION UNIT RATE TOTAL AMOUNT TOTAL AMOUNT

SNO. M - 2018) DESCRIPTION UNIT RATE TOTAL AMOUNT TOTAL AMOUNT

DSR ( INR ) N0N -DSR ( INR )

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface / recessed medium class PVC

A.18 1.10 conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5

sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point (without independent

switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in

A.19 1.55 surface / recessed PVC conduit, and earthing the point with 1.5 sq.mm. FRLS PVC insulated

copper conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single

A.20 1.5 core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS Metre 11500 265.00 3047500

PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single

A.21 1.6 core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos 4 sq. mm FRLS Metre 150 392.00 58800

PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch

A.22 1.24 box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 2800 111.00 310800

1.24.5 6 pin 15/16 amp socket outlet Each 525 175.00 91875

Supplying and fixing modular blanking plate on the existing modular plate & switch box

A.23 1.26 excluding modular plate as required. Each 200 32.00 6400

Supplying and fixing following size/module, GI box along with Modular base & cover plate on

A.24 1.27 existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC

B.1 1.14 insulated copper conductor, single core cable in surface/ recessed steel conduit as required

1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre 450 146.00 65700

1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 2500 167.00 417500

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 50 200.00 10000

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 50 249.00 12450

1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 150 543.00 81450

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 1000 752.00 752000

Supplying and fixing of following sizes of steel conduit along with accessories in

B.2 1.20 surface/recess including painting in case of surface conduit, or cutting the wall and making

good the same in case of recessed conduit as required.

Supplying and making end termination with brass compression gland and aluminium lugs for

C.2 9.1 following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1

KV grade as required.

Supply of following XPLE armourned 1.1 KV grade conforming to I.S.7098/1554Aluminium

C.4 MR Conductor Cables :

Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor

armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively &

(a) 3.5 C x 120 Sqmm XLPE cable RM 100 850.00 85000.00

(b) 3.5 C x 95 Sqmm XLPE cable RM 50 650.00 32500.00

© 3.5 C x 70 Sqmm XLPE cable RM 50 550.00 27500.00

(d) 3.5 C x 50 Sqmm XLPE cable RM 50 400.00 20000.00

(e) 3.5 C x 35 Sqmm XLPE cable RM 50 600.00 30000.00

D.1 2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as Each 50 8.00 400

required. and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit

D.2 2.10 breaker suitable for inductive load of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

2.10.1 Single pole Each 690 199.00 137310

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB

2.13 complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, vertical type three pole and neutral, sheet steel, MCB

distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral

D.3 2.5 bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as

required. (But without MCB/RCCB/Isolator)

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts,

D.5 2.14 residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in

the existing MCB DB complete with connections, testing and commissioning etc. as required.

E PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

E.9 MR Supply, installation, testing & Commissioning of 1 module 16A SWITCH SP 1 way for pop up Set 80 216.00 17280.00

Supply, installation, testing & Commissioning of 2 module 16 A Socket for floor box box.

Supply, installation, testing & Commissioning of Specific Backbox for Carpet for Floor Box

E.12 MR along with LID and TRIM for tiles/ marble 15 to 20mm thickness material for headband and Set 20 10000.00 200000.00

single cable outlet/ glavanized steel, paint RAL 7031 for floor box .

Supply, installation, testing & Commissioning of Specific Backbox for Wooden Flooring for

E.13 MR Floor Box along with LID and TRIM for tiles/ marble 15 to 20mm thickness material for Set 60 6803.00 408180.00

headband and single cable outlet/ glavanized steel, paint RAL 7031 for floor box.

Supply, installation, testing & Commissioning of flat support plate 8 module for integration of

E.14 MR Mechanism for Floor Box Set 80 263.00 21040.00

Supply, installation, testing & Commissioning of waved support plates for 4 module (2x2)

E.15 MR modules for Floor Box Set 80 1450.00 115999.97

Supplying and fixing following modular switch / socket on the existing modular plate & switch

E.16 1.24 box including connections but excluding modular plate etc. as required.

1.24.7 TV socket outlet Set 30 119.00 3570

Supplying and drawing following pair, 0.5 sq.mm FR PVC insulated copper conductor,

E.17 MR unarmoured telephone cable in the existing surface / recessed steel / PVC conduit as

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways along with

E.20 MR required suitable number of GI couplers for joining raceways and fixing GI brackets and all

accessories complete in all respect as per the directions of engineer in charge

(a) 300mmx38mm(GI) - 3 compartment Mtr 375 3000.00 1125000.00

(b) 225mmx38mm(GI) - 3 compartment Mtr 220 2500.00 550000.00

Supply, Installation, Testing and Commisioning of Junction boxes for direct access to cables

at the intersection of raceways supplied completely with base and cover plates, height

E.21 MR adjustable junction box 65- 90 mm including all accessories complete in all respect as per the

directions of engineer i

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

E.22 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the exisitng Metre 750 33.00 24750

surface/recessed steel/ PVC conduit as required

Supplying and fixing of following sizes medium class PVC conduit aong with accessories in

E.23 1.21 surface/ recess including cutting the wall and making good the same incase of recessed

conduit as required

Supplying and Installation of following size perforated of painting with powder coating M.S.

cable trays of perforation of not more than 17.5% in convinient sections, joined with

E.24 4.1 connectors suspended from the cieleing with MS suspenders including bolts and nuts painting

suspenders etc as required

4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 100 700.00 70000

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and

1 5.6 providing masonry enclosure with cover plate having locking arrangement and watering pipe SET 12 11794.00 141528

of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

4 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. MTR 200 57.00 11400

14 MR Floor Panels

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and

commissioning the following sheet steel cubicle type panels fabricated from 1.6mm thick

CRCA sheet, dust and vermin proof, indoor type TPN Panels with hinged lockable doors

fabricated from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC supply

with rear access for cable alley and with segregated bus-bar chamber with tinned aluminium Each 6 75000.00 450000.00

bus bar and including supplying and fixing following switchgears, meters and accessories,

inter-connections, bonding to earth, powder coated painting and marking as specified. Switch

boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as

detailed in the Specifications

Colour: Gray Powder Coated, as per approved sample.

1 nos, 160 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking

capacity 25 KA (ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 200 Amps capacity with heat shrinkable colored

sleeves and I/C DMC/SMC bus bars supports at required intervals complete for cross section,

size supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB -2 Nos.

(b) 40 Amps, TPN, MCB - 6 nos

Panel complete as above

15 MR UPS Panel

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and

commissioning the following sheet steel cubicle type panels fabricated from 1.6mm thick

CRCA sheet, dust and vermin proof, indoor type TPN Panels with hinged lockable doors

fabricated from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC supply

with rear access for cable alley and with segregated bus-bar chamber with tinned aluminium Each 1 235000.00 235000.00

bus bar and including supplying and fixing following switchgears, meters and accessories,

inter-connections, bonding to earth, powder coated painting and marking as specified. Switch

boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as

detailed in the Specifications

Colour: Gray Powder Coated, as per approved sample.

Three (3) nos, 160 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault

breaking capacity 25 KA (ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 400 Amps capacity with heat shrinkable colored

sleeves and I/C DMC/SMC bus bars supports at required intervals complete for cross section,

size supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

2 Nos. 250A, 4P, MCCB (25kA) with phase indicating lamp protected with 2A, SP, MCB's

along with E/M interlocking

(b) 63 Amps, TPN, MCB - 2 nos

(c ) 40 Amps, TPN MCB - 14 nos

Panel complete as above

Providing and fixing MV danger notice plate of 200mm x 150mm made of mild steel, atleast 2 Nos.

17 2.21 mm thick, and vitreos enamelled white on both sides and with iscription in single red colour on 6 226.00 1356

front side as required

Providing and fixing HT danger notice plate of 250mm x 200mm made of mild steel, atleast 2 Nos.

18 2.22 mm thick, and vitreos enamelled white on both sides and with iscription in single red colour on 2 244.00 488

front side as required

Supply, Installation, Testing and Commissiong of High Efficient 80kVA Model IGBT Rectifier &

IGBT Inverter, Modular Fault Tolerant designFailure in any one of the module the others

keeps supplying to the load without interruption. Approved Make, 12V VRLA Batteries, 65 AH

for 10 minutes backup. Exide (50 nos on each bank) Accessories ( Cabling between UPS and

the Battery upto 10 Mtr distance for each UPS considering cable Routing,Battery Rack and

Battery Interlinks, lugs etc ) DC MCCB between UPS and Battery complete in all respect as

per the directions of engineer in charge

Total of Electrical items 8401265 11258659.97

SCHEDULE OF QUANTITIES - HVAC WORKS

S.NO. DSR (E & M - DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

S.NO. DSR (E & M - DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

UNIT QUANTITY RATE

DSR (INR) N0N-DSR (INR)

Supply, installation, testing and commissioning of Inverter type High Wall Indoor Unit with

a MR High Wall - 2 Tr (Inverter Compressor with stablizer) Nos 2.0 92276.00 184552.00

2.0 MR SITC of Copper Pipe for 2 Tr AC RMT 35.0 3799.00 132965.00

VAV BOX (WITH INTEGRAL SOUND ATTENUATOR)

Supply and Installation of pressure independent rectangular VAV unit with integral sound

attenuator made of 22G GI sheet casing length 900mm consisting of 25mm thick 48kg/m3

3.0 M.R. density fiber glass wool covered with tissue paper ,elliptical volume control damper , calibrated

differential pressure sensor (DPT sensors) at inlet complete with digital Thermostat.( All VAV

shall be factory calibrated )

Supply, installation, testing and commissioning of Variable Frequency Drive (VFD)

380-400 VAC, IP-54 Chassis, RFI class A1 (C2), No brake chopper.

a M.R. VFD 5 HP or as directed by the engineer in charge Nos. 21.0 51566.00 1082886.00

5.0 M.R. Tube Axial Fan

Supply Installation, testing and commissioning of supply air Tube Axial flow fan of following NOS 10.0 217120.00 2171200.00

capacity with GSS casing and aluminium alloy impellers with high efficiency aero-foil sections,

a M.R. blades, the impeller directly driven by TEFC induction motor suitable for 3 Phase 50 Hz 415 V

± 10 %, complete as required. This cost shall include the cost for suitable panel, DOL starter,

breakers etc compete in all respect as per the directions of engineer in charge.

M.R. 9000 cfm at 15 mm static presuure for fresh air With Class "H" insulation.

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch

and return air path as and where required of required sizes i/c control wiring,the damper shall

be motorized and spring return so as to close the damper in the event of power failure

6.0 16.20 automatically and open the same in case of power being restored. The spring return action

shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the

event of fire signal complete as required and as per specifications.

7.0 GI Gravity Louver

Supply, installation, testing and commissioning of GI Gravity Louver complete with SQM 20.0 8950.00 179000.00

a M.R. neoperene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

8.0 VOLUME CONTROL DAMPER

Supply, installation, testing and commissioning of 50 micron powder coated "Aluminium"collar SQM 100.0 8000.00 800000.00

a M.R. volume control dampers with key operated of black painted in supply air registers / terminals.

9.0 MR Insulated Flexible Duct

Supply, installation, testing & commissioning of thermal insulated flexible duct of following

sizes duly supported at regular interval as per site requirement etc. complete as required as

per specifications.

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal

rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers,

16.12.1 vanes, hangers, supports etc. as per approved drawings and specifications of following sheet

thickness complete as required.

Diffusers & Grills

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium SQM 70.0 8480.00 593600.00

volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but SQM 70.0 5507.00 385490.00

without volume control dampers complete as required

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium SQM 30.0 11363.00 340890.00

with aluminium volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium SQM 30.0 7559.00 226770.00

without volume control dampers with anti smudge ring & removable core.

14.0 INSULATION

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed

cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for

16.23 Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile

rubber tape insulation complete as per specifications and as required.

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin SQM 50.0 647.00 32350.00

bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm

16.21 thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm

thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts,

bolts, stick pins, CPRX compound etc. complete as required and as per specifications

DISMANTLING, LIFTING, SHIFTING & REINSTALLING OF EXISTING SYSTEM

Shifting/ Relocation, Installation, Testing and Commissioning of AHU existing complete with NOS 15.0 25000.00 375000.00

17.0 M.R. cabling, insulation, and other materials as required complete in all respect as per the directions

of the engineer in charge.

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water

piping inside the building (with necessary clamps, vibration isolators and fittings but excluding

valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile

18.0 16.2 rubber of minimum 45 Kg / cu m density, thermal conductivity 0.037 W/MK or better at 20 deg

mean temperature class 'O' insulation applied by suitable adhesive complete including

repairing of damage to building etc. as per specifications and as required complete in all

a 16.2.9 80mm dia.(32 mm thick insulation) Metre 50.0 1554.00 77700.00

b 16.2.10 65mm dia.(32 mm thick insulation) Metre 50.0 1247.00 62350.00

Supply installation Sound alternator( return air baffle) of with Acoustic Lining open cell nitrile nos 50.0 9778.00 684456.83

rubber acoustic insulation, with density 140-180 kg/cum. and having anti fungal & anti bacterial

19.0 MR properties as per DIN EN ISO 846, MATHOD A&C. as per ASTM Standard C 1071-05. 10

Supply, Installation and Testing of fresh air grilles of powder coated / anodised extruded Sqmt 4.0 14244.00 56976.79

20.0 MR aluminium with GI wire mesh, inlet louvers,Box type VCD & bird screen, as per the

approved shop drawings and specifications.

Supply, Installation and Testing of Butterfly damper of aluminium sheet construction with

two flap with sleeve as per thespecifications and shop drawings.

Supply, Installation and Testing of single piece GI round spigot made out of spinning

22.0 MR process with 50mm height and having grooves on both sides and circular flanges. Spigots

shall be installed on main ducts to facilitate connection of flexible ducts.

Installation of plenum box with insulation 24 G GI sheet construction plenum box insulation Nos 20.0 4003.00 128114.30

Supply Installation, Testing and Commissioning of Inline fan suitable for following capacities

complete with sheet metal casing , electric motor and direct driven centrifugal fan suitable for

operation on 415 +/-10% V,50 Hz , 3 phase or 240 +/- 10% V,50 Hz, 1 phasefitted with speed

24.0 MR regulator in case of single phase including provision of 15 Amp plug and wiring between the

fan and the socket and accessories like flexible connectors , gravity louvers , wire guard & bird

screen etc.The fans shall be acoustically insulated from inside to reduce the db levels. All the

fans used for purging of FM 200 shall be fitted with fire dampers which shall be charged as per

500 CFM,15 MM STATIC PRESSURE Nos 2.0 11702.00 11702.75

300 CFM,15 MM STATIC PRESSURE Nos 3.0 8315.00 8315.11

150 CFM,20 MM STATIC PRESSURE Nos 3.0 6775.00 20325.83

25.0 MR Supply Installation, Testing and Commissioning Drain pump for Split Acs Nos 2.0 16168.00 32336.54

Plasma Ionization on Recirculating Air

Supply, Installation, Testing and commissioning of comprehensive Air Purification system in

the specified areas where AHU/VRV/ Cassette /Hi-wall / Ductable units etc are installed , so

as to improve Indoor air quality by using Needlepoint Bi-polar Ionization technology, which

produces a natural Bio Climate rich in positive and negative ions. The Needle Point Bipolar

26.0 MR Ionizers should not have any consumables and should have a life of 10 years. Project

design should meet standard ASHRAE 62.1 IAQ Procedure for energy saving. System should

kill microorganism and pathogens, remove Odour, VOC and reduce dust particle /particulate

matter / PM2.5 /PM 10. The product should be UL / Intertek listed. Product should have

minimal or negligible pressure drop & low power consumptions. Product should have UL 867

and UL 2998 certification (for zero ozone emission).

Air Quality Monitor

Indoor Air quality monitor to measure Air quality parameters including PM2.5,TVOC, CO2,

27.0 MR Humidity and Temperature.This monitor should be a 3 tier architecture including sensor

Hardware, secure cloud infrastructure, monitoring apps including dashboard, android/IOS

apps, where ever requires

Air Quality Monitor Nos 1.0 64059.00 64059.00

TOTAL HVAC WORKS 7212966.1 12354766.4

SCHEDULE OF QUANTITIES - WIFI & LAN WORKS

DSR/MR SNO. DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR/MR SNO. DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR ( INR ) N0N -DSR ( INR )

SITC of 24 port 10/100/1000 Base T Switch with 4 x 10G SFP+ ports,The Switch should have

16K MAC address, Should have RJ-45 console port should support MSTP and DUAL

configuration, Should support Static Route Entry: IPv4 124; IPv6 50 , Should support IP-MAC-

M.R. 1 Port Binding strictly management network devices preventing illegal access and the Man-in- Nos 18 177137.00 3188466

the-middle attack, Should support Asymmetric VLAN, Auto Voice VLAN, Should support Cable

diagnostics, Time-based PoE: PoE ports can be turned on/off by port or system through

schedule, Operating Temperature -5 to 50°C (23 to 122°F)

SITC of 24 port 10/100/1000 Base T PoE Switch with 4 x 10G SFP+ ports, with 370W PoE

power budget , The Switch should have 16K MAC address, Should have RJ-45 console port

should support MSTP and DUAL configuration, Should support Static Route Entry: IPv4 124;

IPv6 50 , Should support IP-MAC-Port Binding strictly management network devices

M.R. 2 preventing illegal access and the Man-in-the-middle attack, Should support Asymmetric VLAN, Nos. 5 198686.00 993430

Auto Voice VLAN, Should support Cable diagnostics, Time-based PoE: PoE ports can be

turned on/off by port or system through schedule, Operating Temperature -5 to 50°C (23 to

M.R. 3 Supply, Installation, Testing & Commissioning of Modules 10G. Nos 15 31061.00 465915

SITC of Cloud based Access Point, with 1899 Mbps through on 5 GHz and 2.4 GHz, should

have 2 x 10/100/1000 Mbps Ethernet port, 1 x RJ45 Console port, should support

IEEE 802.11a/b/g/n/ac Wave 2 wireless IEEE 802.11acWave 2 wireless, Supports IEEE

802.3at Power over Ethernet (PoE) IEEE 802.3az Energy-Efficient Ethernet (EEE), Integrated

DHCP server, Supports Link Aggregation, should support Personal and Enterprise versions

of WPA/ WPA2, (802.11i)/ WPA3TM, SSID/Guest/Station Isolation

M.R. 4 IP/MAC address filtering, Captive Portal (Facebook, Google, Line, Weibo, E-mail Nos 35 35243.00 1233505

authentication) Supports RADIUS client and Cipher negotiation Allows a high number of

concurrent users, MU-MIMO support, UL2043-certified chassis (Plenum-rated SKU)

Operating: 0 to 40 °C (32 to 104 °F) Storage: -20 to 65 °C (-4 to 149 °F), Mean Time Between

Failure (MTBF) 548,000 hours, Certifications CE Class B, FCC Class B, UL, UL2043, IC Class

Supply, installation, testing & commissioning of Wi-Fi Controller with 4 Gig Ports, with 25 APs

M.R. 5 license,Upgrage up to 50 AP Power Supply alongwith 3 year support. Nos. 1 422243.00 422243

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the

existing surface/ recessed Steel/ PVC conduit as required.

Supplying, installing, testing and commissioning of I/O Jack should be Category 6, TIA568B.2-

1 – 250MHz, I/O Jack should be for 100 W, 22-24 AWG copper cable shall: Use insulation

displacement connectors (IDC), Information outlet (RJ45 jack) should be covered under ETL

M.R. 6 Verification program for compliance with TIA568B.2-1, ETL certificate to be submitted with Nos 1000 409.00 409000

offer the I/O jack should be Blue colour for easy port identification, Operating Life: Minimum

750 insertion cycl

Supplying, installing, testing and commissioning of CAT 6 Patch panel with transmission

performance compliance with the ANSI/TIA/EIA 568C.2 standard. Should allow for a minimum

of 200 re-terminations without signal degradation below standards compliance limit.Should

have self-adhesive, clear label holders and white labels with the panel Panel should be of 1U

M.R. 7 height with 24 port pre-loaded IO. IDC: Suitable for 22-26 AWG stranded and solid wire Nos 55 3870.00 212850

compatible with both 110 & Krone punch down tools, Operating Life: Minimum 750 insertion

cycles support operating Temperature from -20° to +70°

Supply , Installtion , Testing and comissioning of Cat6 1Meter patch cords Blue colour with

high quality four pair twisted stranded cable terminated with RJ45 tangle free modular plugs at

M.R. 8 both the ends. The Conductor should be 24 AWG, Multi-strands & Bare Copper Conductor Nos 1000 263.00 263000

Supply , Installtion , Testing and comissioning of Cat6 2 Meter patch cords Blue Colour with

high quality four pair twisted stranded cable terminated with RJ45 tangle free modular plugs at

M.R. 9 both the ends. The Conductor should be 24 AWG, Multi-strands & Bare Copper Conductor Nos 1000 279.00 279000

Supply , Installtion , Testing and comissioning of Face Plate should be Single Gang square

plate, 86mmx86mm, should have Write on labels, The Faceplates should have inbuilt

M.R. 10 shutters which are compatible with any standard colored keystones jacks. The Faceplates are Nos 1000 112.00 112000

available in one, two and four port variants.

Supply , Installtion , Testing and comissioning of 15U wall mount rack with fans , 2 cable

M.R. 11 managers , satationary shelf , 2 Nos of hardware pkts. Nos 5 10905.00 54525

Supply, Installation, Testing & Commissioning of 42 U Network Rack with 19''PDU 6 points 5

M.R. 12 amp , Stationary shelf, Mounting Hardware(pac. Of 10) , Cable manager Horizontal 1U , Nos 2 62113.00 124226

Fan 230 vac 90 cfm top mounted .

MR 13 Providing and laying of LC- LC multimode OFC type patch cord for data and voice. Nos 16 3206.00 51296

Supplying, laying and fixing of 6 core Corrugated Steel Tape OM3 Multimode Optical Fiber of

MR 14 size 50/125μm LSZH. Indoor/Outdoor Universal loose tube Black Jacket through existing Mtrs. 400 290.00 116000

GI/HDPE/ Hume pipe or on cable trays inside the cable duct including all necessary fixing

accessories e.g. cable

Supplying, installing, ties, hardware

testing etc. Standard

and commissioning & Approval

GB - 50/125μm OM3 LC: 2002, IEC

Supplying, installing, testing and commissioning of 6 port LCS2 Adapter plate, loaded with 3

MR 16 nos. of duplex LC unit for 6 multi mode fibers of size 50/125 μm .Adapters to be compatible to Nos. 5 8800.00 44000

fit in 19" U/UTP 24 port modular patch panel or 24 port LIU.

Supplying, installing, testing and commissioning of LIU 24 port LC type LCS2. Rack Mount 19"

modular type unloaded to be compatible for 4nos of 6 X RJ 45 UTP unit in a block or 6 port

MR 17 SC/LC/ST adapter unit. Material of LIU is Galvanised Steel and Weight is approx 2.605 kg. Nos. 2 9800.00 19600

TOTAL WIFI & LAN WORKS 1470000 8022056

SCHEDULE OF QUANTITIES - CCTV

DESCRIPTION TOTAL

DSR/MR SNO. UNIT QUANTITY RATE TOTAL AMOUNT

DSR/MR SNO. UNIT QUANTITY RATE TOTAL AMOUNT

DSR ( INR ) N0N -DSR ( INR )

Supply, Installation, Testing & Commissioning of 5MP IR IP H.265 Vandal

Proof Dome camera with 2.8 to 12mm Motorized Lens,Smart IR, up to 30M

IR distance,Up to 120 dB WDR (Wide Dynamic Range),3D DNR (Digital

Noise Reduction),H.265+, H.265, H.264, MJPEG,Corridor mode, Triple

streams,3-Axis, IP67, IK10 Vandal Resistant,Colour: 0.005Lux (F1.4, AGC

ON), 0 Lux with IR,Video Compression H.265+, H.265, H.264,

MR 1 MJPEG,Behavior Detection Intrusion, Crossing line, Motion detection, Nos 20 22000.00 440000

Object left, Missing object,Intelligent Identification Face detection, Defocus,

Scene Change,PoE (IEEE802.3 af) Power consumption: Max 7.2W,Edge

Storage Micro SD Card, Up to 256GB, ANR Support,Working Environment

-40°C ~ +60°C, Humidity ≤ 90% RH(Non-condensing),Compatible

Integration ONVIF (Profile S/G), API.

Supply, Installation, Testing and Commissioning of 32Ch Embedded

Network Video Recorder with 4 Sata Supports 1 × RJ45 1000M ,4K

MR 2 Cameras, HDMI, VGA, RAID, Redundant power supply, Smart Analytics Nos 1 126000.00 126000

MR 3 SITC of Hard Disk Drive 4TB, 24/7 surveillance category Only complete No 4 16000.00 64000

etc as required.etc.all complete.

Supply, Installation, Testing & Commissioning of 55" Flat Screen HD led

(24X7) with Interfaces include HDMI, DVI, D-sub, Component and

MR 4 Composite input as well as RS-232C and RJ45 for extensive connectivity, Nos 1 69184.00 69184

remote control and wall mount unit / floor stand complete with making

connections etc complete as reqd.

MR 5 SITC of HDMI cables 10 meters M2M etc all compelte. Nos 2 7600.00 15200

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the

existing surface/ recessed Steel/ PVC conduit as required.

1.53.1 1 run of cable Meters 1500 49.00 73500

SITC of 24 Port Unmanaged POE 10/100/1000 Mbps Switch, Rack

Mountable etc. all complete.

SITC of 8 Port Unmanaged POE 10/100/1000 Mbps Switch, Rack

Mountable etc. all complete.

SITC OF Cat6 UTP 24 Port Loaded Patch Panel/ Cat6 24 Port Panel with

SITC of RJ-45 outlets near the cameras with gang boxetc. all complete.

etc. all complete.

SITC of 12 U RACK STANDARD RACK with ventilation, sliding shelves,

power strips, etc. all complete.

MR 12 SITC of cat 6 Patch Cords 1 meter high quality four pair twisted stranded No 50 489.00 24450

cable terminated with rj45 modular plugs at both the ends.

Supplying and fixing of following sizes medium class PVC conduit aong

1.21 with accessories in surface/ recess including cutting the wall and making

- 2018) good the same incase of recessed conduit as required

SL NO DSR/MR Luminaire Description Image UOM QTY Rate

Supply, Installation, Testing and Commissioing of LED Pendant luminaire with

LED(Light Emitting Diode) system power: 28W, 120 LM/W system efficacy,

colour temperature of 4000K, neutral white, 230V constant current driver, 70%

of luminous flux after 50,000 operating hours, energy efficient LEDs, CRI>80,

luminous flux of 3360 lm, MacAdam 3, T.H.D≤10%, driver efficiency ≥ 88%,

surge protection of 2.5kV, direct light emission, Aluminium body, polyester

white powder coat applied over a 5-stage pre-treatment, Prismatic diffuser for

glare-free uniform light, UGR<19, Electronic control gear

Protection class I, IP40,

L =1195mm, B = 295mm, H = 67mm, PH = 1500mm or its equivalent

Supply, Installation, Testing and Commissioing of Recessed downlightwith

HPE (High-Performance Efficiency) with LED (Light Emitting Diode), system

power: 12 W, Luminous flux of luminaire 1320 lm, 110 LM/W system efficacy,

Colour temperature of 4000 K, Neutral white, CRI > 80, 230V constant current

driver, 70% of luminous flux after 50,000 operating hours; energy-efficient

LEDs, direct light emission, housing in die-cast aluminium, Polyester powder

white coloured coat applied over a 5-stage pre-treatment trim, prismatic

diffuser for homogenous light distribution, ZHLS (ZERO HALOGEN LOW

SMOKE) wiring, Electronic control gear,

Protection class II, IP 40,

Ø = 175 mm, DA(Ø) = 160 mm, H = 59 mm or its equivalent

Supply, Installation, Testing and Commissioing of Pendant luminaire with LED

(Light Emitting Diode), system power 28 W, luminous flux of luminaire 3080

lm, 110 LM/W system efficacy, direct light emission CRI>80, colour

temperature of 4000K, Neutral white, 230V constant current driver, 70% of

luminous flux after 50,000 operating hours, energy efficient LEDs, luminaire

profile in aluminium, Plastic moulded end caps, Polyester powder Aluminium

white coloured coat applied over a 5- stage pre-treatment, high efficiency glare-

3 MR free snap fit micro-prismatic diffuser for homogeneous light distribution, ZHLS no 145 7056.00 1023120

(Zero Halogen Low Smoke) internal wiring, integral Electronic control gear,

adjustable suspender,

Protection class I, IP 20,

L = 1199 mm, B = 75 mm, H = 90 mm, PL max = 1500 mm

Supply, Installation, Testing and Commissioing of COB based surface

mounted/pendent downlight, system power: 10W, 110 Lm/W, luminous flux of

luminaire 1100lm, colour temperature of 4000K, 230V constant current driver,

70% of luminous flux after 50,000 operating hours; energy efficient LEDs,

4 MR direct light emission, housing in aluminium, round, polyester Silver powder no 360 5292.00 1905120

coat applied over a 5-stage pre-treatment, aluminium reflector, 50x80 elliptical

beam,Electronic Control Gear, Protection class I, IP20, Ø = 100 mm, H = 165

mm or its equivalent

Supply, Installation, Testing and Commissioing of Modular recessed luminaire HPE

(High Performance Efficiency) LED (Light Emitting Diode), system power: 44W,

Luminous flux of luminaire 4840 lm, 110 LM/W system efficacy, colour temperature of

4000 K, neutral white, CRI > 80, 230V constant current driver, 70% of luminous flux

after 50,000 operating hours, Energy efficient LEDs, Direct light emission, Luminaire

profile in aluminium, Polyester powder aluminium white coloured coat applied over a

5- stage pre-treatment, Snap fit satin diffuser for a homogenous light distribution

5 MR ZHLS(ZERO HALOGEN LOW SMOKE) internal wiring, integral electronic control gear,

Protection class I, IP 40, MacAdam 3, T.H.D ≤ 10%, driver efficiency ≥ 88%, surge

protection of 2.5kV,

L = 2385 mm, B = 64 mm, H = 64 mm, L(ET) = 1175 mm, B(ET)= 52 mm. or its

Supply, Installation, Testing and Commissioing of Modular recessed luminaire with

HPE (High Performance Efficiency) LED (Light Emitting Diode), system power: 14W,

Luminous flux of luminaire 1540 lm, 120 LM/W system efficacy, colour temperature of

4000 K, neutral white, CRI > 80, 230V constant current driver, 70% of luminous flux

after 50,000 operating hours, Energy efficient LEDs, Direct light emission, Luminaire

profile in aluminium, Polyester powder aluminium white coloured coat applied over a

5- stage pre-treatment, Snap fit satin diffuser for a homogenous light distribution

6 MR ZHLS(ZERO HALOGEN LOW SMOKE) internal wiring, integral electronic control gear, no 24 4410.00 105840

Protection class I, IP 40, MacAdam 3, T.H.D ≤ 10%, driver efficiency ≥ 88%, surge

protection of 2.5kV, or its equivalent

Supply, Installation, Testing and Commissioing of Pendant luminaire with LED (Light

Emitting Diode), system power 32W, luminous flux of luminaire 2880 lm, color

temperature of 4000K, neutral white, direct light emission, 230V, constant current

driver, aluminum support profile, polyester powder coated grey applied over a 5 stage

pre-treatment, prismatic diffuser, Electronic Control Gear,

Protection Class I, IP 20,

L1= 600 mm, L2= 600 mm, L3= 600 mm, H= 67mm, max. PL= 1500 mm or its

Supply, Installation, Testing and Commissioing of Recessed downlight

luminaire with HPE (High-Performance Efficiency) LED (Light Emitting Diode)

system power: 8 W, Luminous flux of luminaire 760 lm, Colour temperature of

4000 K, Neutral white, SDCM 3, CRI > 80, 230 V constant current driver, 70%

of luminous flux after 50,000 operating hours; Energy efficient LEDs, Direct

light emission, Luminaire housing in aluminium, Polyester powder-white

coloured coat applied over a 5- stage pre-treatment, Prismatic diffuser for

8 MR homogenous light distribution, ZHLS (ZERO HALOGEN LOW SMOKE) wiring, no 10 1499.00 14990

electronic control gear,

Protection class II, IP 40

Supply, Installation, Testing and Commissioing of Pendant luminaire with LED

(Light Emitting Diode), system power 14 W, luminous flux of luminaire 1540

lm, direct light emission CRI>80, colour temperature of 4000K, Neutral white,

230V constant current driver, 70% of luminous flux after 50,000 operating

hours, energy efficient LEDs, luminaire profile in aluminium, Plastic moulded

end caps, Polyester powder Aluminium white coloured coat applied over a 5-

stage pre-treatment, high efficiency glare-free snap fit micro-prismatic diffuser

for homogeneous light distribution, ZHLS (Zero Halogen Low Smoke) internal

9 MR wiring, integral Electronic control gear, adjustable suspender, no 8 7850.00 62800

Protection class I, IP 20,

L = 1199 mm, B = 75 mm, H = 90 mm, PL max = 1500 mm or its equivalent

Supply, Installation, Testing and Commissioing of Modular pendant Formation

luminaire made up of 22 nos of linear lights with all connectors and

accessories to give a continuous effect with HPE (High Performance

Efficiency) LED (Light Emitting Diode) system power: 9 W, Luminous flux of

luminaire 990 lm, Colour temperature of 4000 K, Neutral white, CRI > 80, 230

V constant current driver, 70% of luminous flux after 50,000 operating hours,

Energy efficient LEDs, Direct light emission, Luminaire profile in anodised

aluminium, snap fit satin diffuser for a homogenous light distribution, ZHLS (

ZERO HALOGEN LOW SMOKE) internal wiring, Electronic control gear,

10 MR Sliding fixing wire suspension, Each 1 170765.00 170765

Protection class I, IP 40, MacAdam 3, T.H.D ≤ 10%, driver efficiency ≥ 88%,

surge protection of 2.5kV,

Supply, Installation, Testing and Commissioing of Recessed downlight with

LED (Light Emitting Diode) system power: 8 W, Luminous flux of luminaire 640

lm, Colour temperature of 3000 K, Warm white, CRI > 80, 230V constant

current driver, 70% of luminous flux after 50,000 operating hours; energy-

efficient LED, direct light emission, housing in die-cast aluminium, Polyester

powder black coloured coat applied over a 5-stage pre-treatment ceiling trim,

with reflector, beam angle of 11-15°, electronic control gear,

Protection class II, IP 20,

Ø = 60 mm, DA(ø) = 55 mm, H = 82 mm or its equivalent

9.00 : SCHEDULE OF QUANTITIES - FIRE ALARM

SNO. DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

SNO. DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR ( INR ) N0N -DSR ( INR )

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal

detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS

Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with

rate of rise cum fixed tempreature thermistor complete with base as required.

5 17.2.7 Supplying, installation, testing & commissioning of fault isolator complete with base as required. No 50 3257.00 162850.00

Supplying, installation, testing & commisssioning of intelligent addressable programmable

sounder complete as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as

Supplying, installation, testing & commissioning of addressable phone control module complete

Supplying, installation, testing & commissioning of intelligent addressable duct detector including

suitable Photo detector complete with base as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as

Supplying, installation, testing & commissioning of addressable manual call point complete as

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3

12 17.3.1 player (including 6 zone button paging station) with seamless integration facility with main fire No 5 126399.00 631995.00

alarm panel for voice evacuation complete as required

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms

operating at 240 Volt AC Supply complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed

15 17.5.2 copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete Mtr. 1650 141.00 232650.00

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the

17.5.3 existing surface / recessed steel conduit of following pairs, cores and size including connections

and interconnections etc. as required.

16 17.5.3.2 speaker cable Two pair, 2-core, 1.5 sqmm Mtr 1170 85.00 99450.00

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and

accessories like coupler etc. as required.

Supplying & Fixing of battery operated illiminated "EXIT" signage, with 2hrs power Battery

backup complete as required.

Supplying, Installing, Testing & Commissioning of LED technology, High efficiency, Emergency

light s with Function Use as an emergency luminaire Testing system Stand Alone, Housing

Polycarbonate, Glow wire test : 850°C, RAL9003, Type of mounting Surface: Recessed base

for ceiling, double sided cone diffuser, plexi plate diffuser, Degree of protection IP65, Operation

Mode Non Maintained or Maintained & Non Maintained mode selectable, Connection voltage

230V -/+ 5% [220V-240V] 50-60Hz, Permissible ambient: temperature +5°C to +40°C, Battery:

Ni-Cd, Duration 3 hours, Viewing distance 20m or 30m, Insulation class II, 20 mtrs. viewing

distance, Dimensions in mm: 270 x 119 x 49 ; for 30 m viewing distance version: 371 x 170 x 62

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with

microphone assembly complete as required.

21 MR Loop Card capacity of 159 detectors For BMS Fire integration Nos 5 100000.00 500000.00

MR Interface Card for BMS fire integration 45000.00 225000.00

MR Supply of repeater panel having 640 character liquid crystal with backlit control 75000.00 375000.00

TOTAL FIRE ALARM WORKS 3302562.00 1234250.00

SCHEDULE OF QUANTITIES - EPABX

DSR/MR SNO. DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR/MR SNO. DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR ( INR ) N0N -DSR ( INR )

M.R. Supply, Installation, Testing and commissioning of IP based EPABX System expandable upto

1000 ports (IP, Analog, Digital) with below present requirement:

20 IP extension ports lic, 200 analog trunk ports, 02 ISDN PRI (30 channels), 01 PC based

operator console (with PC, IP Phone and Headset), 380 Analog ports having all standard call

related features. Analog and PRI card should be distributed in two gateway for redundency.

The server of IP EPABX should be having Intel Skylake CPU S-4114 or better with 64 bit

Linux Operating System from IP PABX OEM. IP EPABX Server should support Link Level

Redundancy (Fully Duplex) with minimum Dual Gigabit interfaces, 48 GB RDIMMs, HDD

RAID-1/6 reliability and Redundant Power Supplies. IP-PBX system along with IP PBX Server,

IP PBX Gateway IP Phone, Headset should be of same OEM Supplied. The system should

support for voice encoding the following standards:- (i) G.711 (ii) G.729A (iii) G.722 WIDE

M.R. Supply of Type 1 IP Phone . Graphic LCD display with backlight 3 user accounts with multi-

line appearance keys Local and company-wide phone directories .

M.R. Supply Installation, Testing and Commissioning of Analog Speaker Phone with backlight.

TOTAL EPABX WORKS 0 1907126

S No DSR/ MR Description Unit Qty Rate DSR NON DSR

MR 1 Supply, Installation, Testing and Commisioning of smart card reader Nos 10 19,218.00 192,180.00

Supply Installation Testing & Commissioning of Access Control Software Multi Reader and controller

confuguration and upgradable to Enterprise level with unliimited users. Databse Supports: MS SQL,

Oracle, and MS Access database types. Type of technology supports: IRIS Sacnner, Biometric, Face,

MR 2 RFID , etc supports template management , Highly secured communication with server,Allows for real- Nos 1 147,336.00 147,336.00

time monitoring of system status and user activities with optional audio alerts. tamper detection,

network communication loss, and many other system attributes.

SITC of Access IP Master Controller with Enclosure & Power Supply- 1 door Universal 2 Reader TCP/IP

Controller Expandable upto 4 Reader with exit reader module,4 Programmable inputs & 4 outputs 100

mA MAX ),Temperature: 0 to 70°C (35 -150°F); Humidity: 20 to 80% RH (non-condensing) , 3000

USERS & 3000 transactions,2 Reader.

MR 4 Supply, Installation, Testing & Commissioning of 12V, 5 Amp. SMPS with MS Box Certified. Nos 10 2,306.00 23,060.00

Supply, Installation, Testing & Commissioning of Smart card Frequency Excitation (13.56 MHz) Mifare/I-

MR 5 class technology smart Card. Memory Type EEPROM,Complies with ISO/IEC standards for thickness. Nos 10 297.00 2,970.00

Lifetime Warranty.

Supply Installation Testing and Commissioning of double leaf 600 LBS Door Electro Magnetic Lock with complete

MR 6 compatiable Bracket UL Listed.

Supply Installation Testing and Commissioning Touchless Request to Exit button with detection range from 4 to 12

Supply Installation Testing and Commissioning Fire Exit panic Bar single/double Door with EM lock and required

MR 8 accessories all includes.

Supply Installation Testing and Commissioning Emergency Door Release Button, Gree, Key Resettable, Double

MR 9 Pole Double Throw.

MR 10 Supply Installation Testing and Commissioning of Cat 6 Network cable. Mtr 1000 38.00 38,000.00

MR 11 Supply Installation Testing and Commissioning of 8 Core-conductor20 to 22 AWG. Mtr 300 154.00 46,200.00

MR 12 Supply Installation Testing and Commissioning of AC 3 Core Plain Copper conductor, PVC insulated. Mtr 150 109.00 16,350.00

Supplying and fixing of following sizes of medium class PVC conduit along with

1.21 13 accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as

Total Carried to Summary 18,000.00 1,356,201.00

Fire Piping, Hydrants, Sprinklers and Accessories

S No DSR WET RISER AND DESCRIPTION UNIT QTY RATE TOTAL TOTAL AMOUNT

S No DSR WET RISER AND DESCRIPTION UNIT QTY RATE TOTAL TOTAL AMOUNT

SPRINKLER SYSTEM AMOUNT NON-DSR (INR)

Providing, laying, testing & commissioning of 'C'

class heavy duty MS pipe conforming to IS 3589/IS

1239 including Welding, fittings like elbows, tees,

flanges, tapers, nuts bolts, gaskets etc. and fixing the

7 pipe on the wall/ceiling with suitable clamp/support

frame and painting with two or more coats of

synthetic enamel paint of required shade complete

Providing, fixing, testing & commissioning of 15mm

dia quartzoid bulb type sprinklers of rating 68 degree

centigrade with required accessories :

21.1 Pendant type Each 600 484.00 290400.00

DSR WET RISER AND

3 SPRINKLER SYSTEM

Supplying, installation, testing & commissioning of

sprinkler flexible pipe (UL Listed) of

stainless steel complete with 15 NPT on reducer

thread with maximum working pressure of

175 PSI test pressure of 875 PSI (Burst) with branch

25 line (Inlet) 25mm NPT male thread to

sprinkler head (Outlet) 15mm NPT female thread

with reducer, nipple, 2 side brackets, center

bracket, stockbar of following sizes complete as

Providing and fixing ISI Marked of approved make

4 MR Fire Extinguishers complete with all accessories as

per manufacturer's specifications.

MR a) CO2 gas nozzle type - 9 Litre capacity (IS:15683). NOS 25 12297.00 307425.00

b) Mechanical Foam gas cartridge type. 9 Kg

capacity (IS:15683).

c) ABC dry powder stored pressure type 6 kg

capacity (IS:15683).

Grand Total 1993540

Grand Total 1993540

SCHEDULE OF QUANTITIES - Presentation and Unified Conferencing system

DSR/MR SNO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

N0N -DSR ( INR )

Conference Room big (Ground floor)

SITC of 86" diplsay panel with IPS technology, 16:9 aspect ratio, 2840 x 2160 (4K)

native resolution, 500 nits brithness, 178 x 178 degree viewing angle, hard coating

(3H) minimum surface treatment, should be anti glare treatment, should be 24 hours

M.R. 1 operational hours, should be usable in landscape or protrait modes, should have Nos 4 269049.00 1076196.00

atleast 2xHDMI, DP, DVI-D, RGB, Audio, USB 3.0, should have RS232C in/out,

RJ45 In, IR receiver in, pixel sensor in etc all complete.

SITC of professional low profile display design mount for mounting panel TV much

closer to the wall, not more than 35mm(1.4”) distance from the wall, should fit flat

panel fits most 32"-89" flat panel display, VESA compliance :

capacity upto 90 kgs, Material : SPCC with coating finished, surface treatment:

Powder painting coating finished, Color: Black etc all complete

SITC of table flip top cable manager with 2 x universal Power socket, 6 pass through

holes with Net Line, USB line, VGA line, Video Line.

SITC of High efficiency class D amplifier with eficiency of atleast 85%, should have

reasonable heat dissipation, 1U standard 19-inch industrial standard, 2 channel

digital power amplifier to provide two 100V or 4-16Ω output terminal wiring speaker,

with 100V transformer output and can switch resistance between 4 and 16 Ω output.,

M.R. 4 shoudl support fault output function, which can remotely monitor the working status Nos 4 51247.00 204988.00

of power amplifier, shoudl have short circuit, overload and overheating protection

function, should come with atleast 2-channel Euro-type balanced input and 2-

channel Euro-type output etc all complete.

SITC of two way ceilng speaker with ABS enclosure 16 watts of peak power handling

capacity, Power Taps @100V: 3.8W, 7.5W, 12W, 16W, Power Taps @70V: 1.9W,

M.R. 5 3.8W, 7.5W, 16W, Cut out Size: 208mm etc all complete. Nos 16 18705.00 299280.00

SITC of 20x optical zoom PTZ camera ,USB/HDMI Video Output,Sleek and

intelligent design, should have Plug & Play USB3.0 Connectivity,C rystal clear

HD1080P image quality, accurate,smooth and silent PTZ Movement, Preset: 9 via

IR remote setting (256 via RS232), Wide field of view with no video distortion, 1/3

inch high quality, 2.38MP (16:9) CMOS sensor, with Full Glass Lens Material, should

support ceiling mount, wall mount and tripod mount (Reverse mountable), 2D and

3D NR for best video quality in different lighting conditions, should support Visca,

M.R. 6 Pelco-P, and Pelco-D protocol, RS232/RS485 Camera Control, should be Nos 4 224207.00 896828.00

compatible with most leading video conferencing software and platform etc all

SITC of USB speakerphone with 8M 360 degrees pickup radius, should be pluga dn

play, should connect to laptop and tablet via USB, Built-in high-fidelity all-pointing

provide 360degree audio pickup over 8 m, should have Echo cancellation and noise

reduction, should be compatible with all leading UC platform, Perfect for PC,smart

M.R. 7 phone or tablet, should comes with two expansion mics etc all complete. Nos 4 108901.00 435604.00

SITC of 9U rack with inbuilt power strip, 2 x low noise fans etc all complete

M.R. 9 SITC of HDMI cables 10 meters M2M etc all compelte . Nos 16 9609.00 153744.00

M.R. 10 SITC of USB cables 10 meters M2M etc all compelte . Nos 40 9609.00 384360.00

M.R. 11 SITC of speaker cable etc all complete. Meters 300 115.00 34500.00

SITC of various video cables and connectors of various lengths included but not

M.R. 12 limited to HDMI, VGA + audio as per design requirements etc all compelte Lot 4 32030.00 128120.00

Conference room small

SITC of 55" diplsay panel with IPS technology, 16:9 aspect ratio, 2840 x 2160 (4K)

native resolution, 500 nits brithness, 178 x 178 degree viewing angle, hard coating

(3H) minimum surface treatment, should be anti glare treatment, should be 24 hours

M.R. 13 operational hours, should be usable in landscape or protrait modes, should have Nos 4 69184.00 276736.00

atleast 2xHDMI, DP, DVI-D, RGB, Audio, USB 3.0, should have RS232C in/out,

RJ45 In, IR receiver in, pixel sensor in etc all complete.

SITC of professional low profile display design mount for mounting panel TV much

closer to the wall, not more than 35mm(1.4”) distance from the wall, should fit flat

panel fits most 32"-89" flat panel display, VESA compliance :

capacity upto 90 kgs, Material : SPCC with coating finished, surface treatment:

Powder painting coating finished, Color: Black etc all complete

SITC of table flip top cable manager with 2 x universal Power socket, 6 pass through

M.R. 15 holes with Net Line, USB line, VGA line, Video Line Nos 4 19858.00 79432.00

M.R. 16 SITC of HDMI cables 10 meters M2M etc all compelte . Nos 16 8328.00 133248.00

M.R. 17 SITC of USB cables 10 meters M2M etc all compelte . Nos 4 7047.00 28188.00

SITC of various video cables and connectors of various lengths included but not

M.R. 18 limited to HDMI, VGA + audio as per design requirements etc all compelte Lot 4 32030.00 128120.00

Board room (fourth floor)

Supply, Installation, Testing and Commissioning of 2ft X 2ft ceiling tile with 28no.

Omni directional microphone and four corner lighting indications, dante conectivity :

dual & redundant, power over ethernet etc complete required as per specifications or

SITC of 48" diplsay panel with IPS technology, 16:9 aspect ratio, 2840 x 2160 (4K)

native resolution, 500 nits brithness, 178 x 178 degree viewing angle, hard coating

(3H) minimum surface treatment, should be anti glare treatment, should be 24 hours

M.R. 20 operational hours, should be usable in landscape or protrait modes, should have Nos 2 69184.00 138368.00

atleast 2xHDMI, DP, DVI-D, RGB, Audio, USB 3.0, should have RS232C in/out,

RJ45 In, IR receiver in, pixel sensor in etc all complete.

SITC of professional low profile display design mount for mounting panel TV much

closer to the wall, not more than 35mm(1.4”) distance from the wall, should fit flat

panel fits most 32"-89" flat panel display, VESA compliance :

M.R. 21 capacity upto 90 kgs, Material : SPCC with coating finished, surface treatment: Nos 1 5765.00 5765.00

Powder painting coating finished, Color: Black etc all complete

SITC of table flip top cable manager with 2 x universal Power socket, 6 pass through

M.R. 22 holes with Net Line, USB line, VGA line, Video Line Nos 4 19218.00 76872.00

SITC of standalone matrix switcher offering 6x HDMI in: 19-pin type A,6x HDMI Out:

19-pin type A,6x Audio Out: RCA Female Stereo (L/R),6x S/PDIF Out: RCA

Female,2ch PCM | Multi Channel Up to 5.1 DTS and Dolby Digital,1920x1080p

@60Hz 12bit,Supported Standards DCI | RGB | HDR | HDR10 | Dolby Vision | HLG |

BT.2020 | BT.2100,Communication and Control HDMI 2.0 | HDCP 2.2 | EDID Input

supports DVI/D and DisplayPort Dual-Mode (DP++) v1.3 with adapter (not

M.R. 23 included),CEC power triggering | Requires CEC compatibility,IR 1x Front Panel IR Nos 1 832770.00 832770.00

Sensor | Handheld IR Remote Included | 1x IR Ext 3.5mm (1/8in) TRS Stereo,RS-

232,1x RS-232: 9-pin DB9 Female | Matrix Control | Telnet commands

supported,Ethernet 1x LAN: 8-pin RJ-45 Female | 10/100 Mbps auto-negotiating |

Built-in Web UI | IP Control, Safety and Emission CE | FCC | RoHS, or its equivalent

SITC of High efficiency class D amplifier with eficiency of atleast 85%, should have

reasonable heat dissipation, 1U standard 19-inch industrial standard, 2 channel

digital power amplifier to provide two 100V or 4-16Ω output terminal wiring speaker,

with 100V transformer output and can switch resistance between 4 and 16 Ω output.,

M.R. 24 shoudl support fault output function, which can remotely monitor the working status Nos 1 55732.00 55732.00

of power amplifier, shoudl have short circuit, overload and overheating protection

function, should come with atleast 2-channel Euro-type balanced input and 2-

channel Euro-type output etc all complete .

SITC of two way ceilng speaker with ABS enclosure 16 watts of peak power handling

capacity, Power Taps @100V: 3.8W, 7.5W, 16W, Power Taps @70V: 1.9W, 3.8W,

M.R. 25 7.5W, 16W, Cut out Size: 208mm etc all complete. Nos 8 17937.00 143496.00

SITC of table top conferencing chairman unit for fully digital conference system,

should have priority function, should have functionality to initiate and end attendance

sign, should have capability for voting, should have capacitive button, should

M.R. 26 operate on controller powersupply, frequency response should be 20Hz -20KHz, Nos 1 45354.00 45354.00

SNR>80dB, channel crosstalk >80db, maximum power dissipation should not be

more than 1.1W etc all complete

SITC of table top conferencing delegate unit, should have capacitive button, should

operate on controller powersupply, frequency response should be 20Hz -20KHz,

M.R. 27 SNR>80dB, channel crosstalk >80db, maximum power dissipation should not be Nos 16 38436.00 614976.00

more than 1.1W, should be supplied with all required accessories etc all complete.

SITC of conference central control unit should be capable of 100M network digital

audio and control signal transmission over cat cable, built-in with high performance

CPU, which sets translation, discussion, attendance, voting, electronic plate as a

whole for future system expansion, should support nNon compressed audio

transmission, 48K sampling rate, 20Hz~20KHz bandwidth perfect sound, the system

should pen 8 microphones at the same time ,shoudl support atleast 32 bit high speed

DSP floating-point processing, supports 2 channel audio output at the same time,

acoustic feedback suppression, noise elimination, and digital equalization provide

M.R. 28 high sensitive and perfect sound, shoudl include management software, TCP/IP Nos 1 256237.00 256237.00

control, provide reliable control and safety managemen, unit and intelligent fault

analysis, can analyze the meeting unit type, quantity, distribution, fault etc, should

have hot standby, the system can normally operate eventhough one of the

controllers broken down etc all complete . or its equivalent

SITC of conference camera controller, should be integrate with supplied PTZ camera

M.R. 29 and digital conference controller for look at me function etc all complete or its Nos 1 224207.00 224207.00

SITC of 20x optical zoom PTZ camera ,USB/HDMI Video Output,Sleek and

intelligent design, should have Plug & Play USB3.0 Connectivity,C rystal clear

HD1080P image quality, accurate,smooth and silent PTZ Movement, Preset: 9 via

IR remote setting (256 via RS232), Wide field of view with no video distortion, 1/3

inch high quality, 2.38MP (16:9) CMOS sensor, with Full Glass Lens Material, should

support ceiling mount, wall mount and tripod mount (Reverse mountable), 2D and

3D NR for best video quality in different lighting conditions, should support Visca,

Pelco-P, and Pelco-D protocol, RS232/RS485 Camera Control, should be

compatible with most leading video conferencing software and platform etc all

complete. or its equivalent

SITC of audio digital signal processor with balanced mic with atleast inputs, 2

balanced Mic/Line inputs and 1 stereo unbalanced input, 1 stereo and 2 mono

outputs, 2-channel USB audio interface for soft codec (Skype, WebEx) integration or

playback from computer, Full digital processing on inputs and outputs, 8 x 3 audio

M.R. 31 routing matrix, 6-channel Smart Mix (gate or gain sharing), Onboard acoustic echo Nos 1 140930.00 140930.00

canceler (AEC) processing, Front panel direct operation and Web Remote

functionality, IP control for third-party CCS administration, Up to 6 mixers can be

linked using Cat5e cable etc all complete. or its equivalent

Supply, Installation,Testing & Commissioning of Integrated Controller One RS-

232/422/485 COM port with hardware and software handshaking Two RS-232 COM

ports with software handshaking only 8 IR/serial, 8 relay, and 8 Versiport I/O ports

Native BACnet®/IP support,Backwards compatible to run existing SIMPL programs

Full Unicode (multi-language) support Increased network throughput and

security,Secure access though Active Directory integration or standalone account

M.R. 32 management Hardware level security using 802.1x authentication,JITC certified Nos 1 237019.00 237019.00

model available for use in secure network environments,IIS v.6.0 Web Server,IPv6

ready,Front panel USB computer console port,1-space rack-mountable SDRAM: 512

MB,Flash: 4 GB,Memory Card: supports SD™ and SDHC™ cards up to 32

GB,External Storage: support USB mass storage devices up to 1 TB. or its

Supply, Installation,Testing & Commissioning of iPad,Apple iOS 8; 9.7-Inch Retina

Display; 2048x1536 Resolution A8X Chip with 64-bit Architecture; M8 Motion

Coprocessor Wi-Fi (802.11a/b/g/n/ac); 32 GB Capacity 8 MP iSight Camera;

FaceTime HD Camera Up to 10 Hours of Battery Life or its equivalent

SITC of 16U Rack made of sheet Metal, ventilation with one side exhaust fan

provision at top of one side, should have lock with keys on front, back doors and

sides, side Door should be removable for easy installation and later maintenance,

M.R. 34 with lock & key, should have power Strips, rack plates, Cable Routing Perforation Nos 1 35873.00 35873.00

and 4 Spin Wheels etc all complete

M.R. 35 SITC of speaker cable etc all complete. Meters 100 115.00 11500.00

M.R. 36 SITC of CAT5e/CAT6 Control&Signal cable etc all complete. Meters 100 115.00 11500.00

SITC of 20/22AWG microphone cable(as per actual) etc all complete.

M.R. 38 SITC of HDMI cables 1.5 meters M2M etc all compelte . Nos 2 3203.00 6406.00

M.R. 39 SITC of cables 1.5 meters VGA + audio etc all compelte . Nos 2 2562.00 5124.00

M.R. 40 SITC of USB cables 10 meters M2M etc all compelte . Nos 2 9609.00 19218.00

SITC of various video cables and connectors of various lengths included but not

M.R. 41 limited to HDMI, VGA + audio as per design requirements etc all compelte Lot 1 128119.00 128119.00

CMD conference room

SITC of 4K 65" display with inbuilt OPS, multi touch, should have windows 10

professiona, suport one touch switching to windows and android, i5, 8 gb RAM,

DLED backlight display, 3b40*2160, brightness 450 nits, IR tocuh 10 point, LAN

M.R. 42 input interface, HDMI input x 2, VGA input port, PC AUDIO INPUT, USB interface of Nos 1 125556.00 125556.00

external device touch, USB 2.0 X 2, should have inbuilt speaker etc all complete .

SITC of professional low profile display design mount for mounting panel TV much

closer to the wall, not more than 35mm(1.4”) distance from the wall, should fit flat

panel fits most 32"-89" flat panel display, VESA compliance :

M.R. 43 capacity upto 90 kgs, Material : SPCC with coating finished, surface treatment: Nos 1 5765.00 5765.00

Powder painting coating finished, Color: Black etc all complete

SITC of table flip top cable manager with 2 x universal Power socket, 6 pass through

M.R. 44 holes with Net Line, USB line, VGA line, Video Line Nos 1 25624.00 25624.00

M.R. 45 .SITC of HDMI cables 10 meters M2M etc all compelte . Nos 1 9609.00 9609.00

M.R. 46 SITC of USB cables 10 meters M2M etc all compelte . Nos 1 9609.00 9609.00

SITC of various video cables and connectors of various lengths included but not

M.R. 47 limited to HDMI, VGA + audio as per design requirements etc all compelte Lot 1 25624.00 25624.00

Conference room 1 & 2

SITC of 55" diplsay panel with IPS technology, 16:9 aspect ratio, 2840 x 2160 (4K)

native resolution, 500 nits brithness, 178 x 178 degree viewing angle, hard coating

(3H) minimum surface treatment, should be anti glare treatment, should be 24 hours

M.R. 48 operational hours, should be usable in landscape or protrait modes, should have Nos 3 69184.00 207552.00

atleast 2xHDMI, DP, DVI-D, RGB, Audio, USB 3.0, should have RS232C in/out,

RJ45 In, IR receiver in, pixel sensor in etc all complete. or its equivalent

SITC of professional low profile display design mount for mounting panel TV much

closer to the wall, not more than 35mm(1.4”) distance from the wall, should fit flat

panel fits most 32"-89" flat panel display, VESA compliance :

M.R. 49 capacity upto 90 kgs, Material : SPCC with coating finished, surface treatment: Nos 2 5765.00 11530.00

Powder painting coating finished, Color: Black etc all complete

SITC of table flip top cable manager with 2 x universal Power socket, 6 pass through

holes with Net Line, USB line, VGA line, Video Line or its equivalent

SITC of 12x optical zoom PTZ camera ,USB/HDMI Video Output,Sleek and

intelligent design, should have Plug & Play USB3.0 Connectivity,C rystal clear

HD1080P image quality, accurate,smooth and silent PTZ Movement, Preset: 9 via

IR remote setting (256 via RS232), Wide field of view with no video distortion, 1/3

inch high quality, 2.38MP (16:9) CMOS sensor, with Full Glass Lens Material, should

M.R. 51 support ceiling mount, wall mount and tripod mount (Reverse mountable), 2D and Nos 2 192178.00 384356.00

3D NR for best video quality in different lighting conditions, should support Visca,

Pelco-P, and Pelco-D protocol, RS232/RS485 Camera Control, should be

compatible with most leading video conferencing software and platform etc all

complete. or its equivalent

SITC of USB speakerphoen with 8M 360 degrees pickup radius, should be pluga dn

play, should connect to laptop and tablet via USB, Built-in high-fidelity all-pointing

provide 360degree audio pickup over 8 m, should have Echo cancellation and noise

M.R. 52 reduction, should be compatible with all leading UC platform, Perfect for PC,smart Nos 2 128119.00 256238.00

phone or tablet, should comes with two expansion mics etc all complete.

M.R. 53 SITC of HDMI cables 10 meters M2M etc all compelte . Nos 4 10262.00 41048.00

M.R. 54 SITC of USB cables 10 meters M2M etc all compelte . Nos 2 10262.00 20524.00

SITC of various video cables and connectors of various lengths included but not

M.R. 55 limited to HDMI, VGA + audio as per design requirements etc all compelte Lot 2 32030.00 64060.00

SITC of 43" diplsay panel with IPS technology, 16:9 aspect ratio, 2840 x 2160 (4K)

native resolution, 300 nits brithness, 178 x 178 degree viewing angle, hard coating

(3H) minimum surface treatment, should be anti glare treatment, should be 24 hours

M.R. 56 operational hours, should be usable in landscape or protrait modes, should have Nos 10 51247.00 512470.00

atleast 2xHDMI, DP, DVI-D, RGB, Audio, USB 3.0, should have RS232C in/out,

RJ45 In, IR receiver in, pixel sensor in etc all complete.

Snos. Item Specifications Unit Total Qty Rate Amount Ref. Image

Supplying and placing in position Main desk of the following specifications. The Main table

shall be of size 3600 Width mm x 1080 mm Depth x 750 mm height. Top surface of the

table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and

final coating of PU. The Main desk should contain in Smart Case - space slides effortlessly

CMD in style.The mobile Pedestal shall be of size 480 Width mm x 640 Depth mm x 600

Suite Height mm. Mobile pedestal shall be coated of MDF (medium density fiber ) with veneer

coating and PU coating.The ERU Top shall be of MDF (medium density fiber) board duly

finished with veneer and final PU coating. Size of ERU top 1900 Width mm x 480 Depth

mm x 550(not from ground with castors).The main desk is provided eith the wire

management system also there is perfect storage side unit .

Providing and positioning HB executive arm chair of approved make and design in

accordance with EN 1335-1 having Die cast aluminium FlowMotion mechanism with

individual adjustment of backrest resistance.Synchronized aluminium mechanism:

automatic initial setting of the backrest tension to the user weight seat height

adjustment from 405 -505 mm with Pneumatic gas lift.Back lock at upright position

Integrated Armrest height 220mm.Integrated height adjustable neck cushion and high

backrest of 730 mm, Adjustable Lumber support, 360° Swivel.seat shell with integrated

2 Main Chair armrests and height-adjustable neck cushion (Highback). SEAT AND BACK:-Backrest Each 1 400,936.00 400,936.00

shell made of plastic; seat and back upholstery made of polyurethane foam. Robust

100% Leather cover with distinctive ,even grains, thickness of 1.1-1.3 mm, Fastness to

light: Type 6 DIN EN ISO 105 B02, Fastness to rubbing:Grade 4 dry and wet DIN ISO

11640. All leather covers are removable, leather Covers not to be pasted with glue on

seat and back.DIMENSIONS: 445-675mm ( W) x 1250-1370 mm (H) x 440-460mm

(D).BASE:-Five star base of polished die cast aluminium with double castors of diameter

Providing and positioning Executive Medium back executive arm chair of approved

make and design in accordance with EN 1335-1.MECHANISM:- Die cast aluminium Flow

Motion mechanism with individual adjustment of backrest resistance.Synchronized

aluminium mechanism: automatic initial setting of the backrest tension to the user

weight seat height adjustment from 420-530 mm with Pneumatic gas lift.Back lock at

upright position,Integrated Armrest height 220mm,Medium backrestof height 540

mm,Adjustable Lumber support,360° Swivel.SEAT AND BACK:-seat shell with integrated

3 Visitor Chair Each 4 299,167.00 1,196,668.00

armrests and height-adjustable neck cushion (Highback). Backrest shell made of plastic;

seat and back upholstery made of polyurethane foam. Robust 100% Leather cover with

distinctive ,even grains, thickness of 1.1-1.3 mm, Fastness to light: Type 6 DIN EN ISO

105 B02, Fastness to rubbing:Grade 4 dry and wet DIN ISO 11640,All leather covers are

removable, leather Covers not to be pasted with glue on seat and back.DIMENSIONS:

445-675mm ( W) x 970-1090 mm (H) x 440-460mm (D).BASE:-Five star base of

polished die cast aluminium with double castors of diameter 60mm

Supplying and Placing in place of 3 seater sofa. The overall dimensions of the sofa shall

be 2060W x 905D x 855H. The seat should be made of PU foam with Density 28 ± 2

kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu.

Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should

be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of

4 supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Each 1 42,297.00 42,297.00

Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also

shall be resistance and termite proof as per IS:303.) and pinewood of cross section

deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring

assembly is mounted over understrucrure for cushioning effect. It should be a welded

assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Supplying and Placing in place of 2 seater sofa. The overall dimensions of the sofa shall

be 1460W x 905D x 855H. The seat should be made of PU foam with Density 28 ± 2

kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu.

Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should

be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of

5 supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Each 1 32,073.00 32,073.00

Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also

shall be resistance and termite proof as per IS:303.) and pinewood of cross section

deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring

assembly is mounted over understrucrure for cushioning effect. It should be a welded

assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes

Center made in SS 202 grade for fixing with understructure. It shall be a welded assembly

Table made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table

shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes

Side made in SS 202 grade for fixing with understructure. It shall be a welded assembly

Table made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table

shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm.

Providing and positioning Softshell chair ,design conforming to GREENGUARD indoor air

quality Certification, GS certificate, and in accordance with EN 1335-1 and ANSI/BIFMA

standards X5-1-2017-02 from TUV Rheinland, furniture testing insitute ,

Nurnberg.MECHANISM:-Seat height adjustment with Pneumatic gas lift.Seat dimension

450 x 470 mm,360° Swivel.SEAT AND BACK:-Seat, and backrest cushions made of CFC

free polyurethane foam upholstered with Plano fabric . Seat height adjustment is 385-

500 mm,flexible upper backrest shell.Armrests are integrated in the seat shell.With two

8 seams along the sides of the backrest.Seat and back frame made of fibreglass reinforced Each 7 90,883.00 636,181.00

polyamide, all polyamide components are labelled according to ISO 11469:2000.Seat,and

backrest cushions made of CFC free polyurethane foam upholstered with fabric (100%

polyester (265g / m²) ). Abression Resistance 80000 martindale, Fastness to light -Type

6.All fabric covers are removable, fabric Covers not to be pasted with glue on seat and

back.DIMENSIONS: 450-620 mm ( W) x 765-895 (H) x 470-565 mm (D), Armrest Ht.

211 mm. BASE:-Five star base of polished die cast aluminium with double castors of

Providingin place of main table with overall size of table 2100 x 2250 x 750mm. The main

table shall be of size 2100 x 1050 x 750mm. The side unit shall be 1200 x 500 x 750mm.

The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-

14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap

within-build power box are provided on work surface for wire management. The ERU top

is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998

with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm

9 GM Cabin thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC Each 8 129,805.00 1,038,440.00

membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated

twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick

PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2

grade and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer

fronts made of 25 mm thick MDF one side pre-laminate board with 0.4 mm PVC

membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses

powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.

Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of

opening. Pedestals are provided with lock for security.

The Back Unit shall be of dimensions 1800 x 500 x 750mm. It shall be made of 25mm

thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC

membrane pressed on to top. The Slide door unit is made of 25 mm thick Pre-laminated

twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick

PVC lipping. Shutters have a soft closing & anti slam mechanism. Handles are provided

for ease of opening. Storage is provided with lock for security.

Providing and positioning Chair of design conforming to GREENGUARD indoor air quality

Certification, Blue Angel, GS certificate, LGA Nurenberg for Ergonomics Approval and in

accordance with EN 1335-1 and ANSI/BIFMA standards X5-1-2011 from TUV Rheinland,

furniture testing insitute , Nurnberg.MECHANISM:-Synchronized die cast aluminium

flowmotion mechanism with forward and backwad tilt: automatic initial setting of the

backrest tension to the user weight. Seat height adjustment with Pneumatic gas lift.Seat

dimension 400 x 485 mm with depth adjustemnt of 50 mm.Back lock at upright

position.Height, width and depth-adjustable, 360° swivel 3D armrests. Armrest supports

of polished aluminum. Armrest sleeves of polyamide in basic dark or soft grey to match

G M Main the frame color,360° Swive.SEAT AND BACK:-Seat, and backrest cushions made of CFC

Chair free polyurethane foam upholstered with 100% genuine leather . Seat height adjustment

is 400-520 mm, backrest height 870 mm and width 485 mm.Seat and back frame made

of fibreglass reinforced polyamide, frame in basic dark or soft grey, all polyamide

components are labelled according to ISO 11469:2000.Robust 100% Leather cover with

pigmented and embossed with distinctive ,even grains, thickness of 1.1-1.3 mm,

Fastness to light: Type 6 DIN EN ISO 105 B02, Fastness to rubbing:Grade 4 dry and wet

DIN ISO 11640.All leather covers are removable, leather Covers not to be pasted with

glue on seat and back.DIMENSIONS: 485-700-900 mm ( W) x 1215-1385 mm (H) x 540-

900 mm (D).BASE:-Five star base of polished die cast aluminium with double castors of

Providing and positioning Softshell chair ,design conforming to GREENGUARD indoor air

quality Certification, GS certificate, and in accordance with EN 1335-1 and ANSI/BIFMA

standards X5-1-2017-02 from TUV Rheinland, furniture testing insitute ,

Nurnberg.MECHANISM:-Seat height adjustment with Pneumatic gas lift.Seat dimension

450 x 470 mm,360° Swivel.SEAT AND BACK:-Seat, and backrest cushions made of CFC

free polyurethane foam upholstered with Plano fabric . Seat height adjustment is 385-

500 mm,flexible upper backrest shell.Armrests are integrated in the seat shell.With two

12 Visitor Chair seams along the sides of the backrest.Seat and back frame made of fibreglass reinforced Each 21 90,883.00 1,908,543.00

polyamide, all polyamide components are labelled according to ISO 11469:2000.Seat,and

backrest cushions made of CFC free polyurethane foam upholstered with fabric (100%

polyester (265g / m²) ). Abression Resistance 80000 martindale, Fastness to light -Type

6.All fabric covers are removable, fabric Covers not to be pasted with glue on seat and

back.DIMENSIONS: 450-620 mm ( W) x 765-895 (H) x 470-565 mm (D), Armrest Ht.

211 mm. BASE:-Five star base of polished die cast aluminium with double castors of

Supplying and Placing in place of 3 seater sofa. The overall dimensions of the sofa shall

be 2060W x 905D x 855H. The seat should be made of PU foam with Density 28 ± 2

kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu.

Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should

be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of

13 supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Each 9 42,297.00 380,673.00

Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also

shall be resistance and termite proof as per IS:303.) and pinewood of cross section

deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring

assembly is mounted over understrucrure for cushioning effect. It should be a welded

assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall

be 860W x 905D x 855H. The seat should be made of PU foam with Density 28 ± 2

kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu.

Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should

be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of

14 supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Each 7 3,059.00 21,413.00

Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also

shall be resistance and termite proof as per IS:303.) and pinewood of cross section

deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring

assembly is mounted over understrucrure for cushioning effect. It should be a welded

assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes

Center made in SS 202 grade for fixing with understructure. It shall be a welded assembly

Table made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table

shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes

Side made in SS 202 grade for fixing with understructure. It shall be a welded assembly

Table made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table

shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm.

Providingin place of main table with overall size of table 1800 x 1800 x 750mm. The main

table shall be of size 1800 x 900 x 750mm. The side unit shall be 900 x 500 x 750mm.

The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-

14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap

within-build power box are provided on work surface for wire management. The ERU top

is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998

with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm

17 PA Table thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC Each 7 85,254.00 596,778.00

membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated

twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick

PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2

grade and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer

fronts made of 25 mm thick MDF one side pre-laminate board with 0.4 mm PVC

membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses

powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.

Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of

opening. Pedestals are provided with lock for security.

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of

injection moulded glass filled nylon & upholstered using net fabric with high tenacity

yarn. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with

density =55+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25%

compression. The armrest has an up=Down adjustment of 8.5 ± 0.5cm which is provided

in armrest structure. Armrest top has an integrated layer of thermoplastic elastomer.

Armrest is made up of plastic injection moulded nylon with textured top. It shall have

Main Front pivot synchro mechanism with following features. 360 degree revolving type, Single

Chair point control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock

feature, seat/back tilting ration of 1:2. The lumber support consists of polypropylene pad

with mouled polyurathene foam & covered with polyester fabric. The height of lumber

pad can be adjusted through two projecting knobs provided on the rear side of the pad.

Lumber pad has an adjustment of 8.0± 0.5 cm in height. The must be greenguard

certified. the work shall be carried out as per guidance and instructions recieved from

Engineer Incharge. This shall come along a headrest from same family. It shall be SCS

IAQ certified for Indoor Air Quality.

The Back Unit shall be of dimensions 1000-1400 x 500 x 750mm. It shall be made of

19 Back Unit 25mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 Each 7 11,957.00 83,699.00

mm PVC membrane pressed on to top. Or as per site requirement

Worktop shall be Made of 36mm thick MDF one side prelaminate board with 0.4mm PVC

membrane pressed on to top and having chamfered edge. Plastic ABS access flap is

provided for easy access to wires and cables. Work top is available as per layout. The

Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-

P2 grade and approved shade Edge banded with matching 2 mm thick PVC lipping.

Aluminium alloy 63400 - WP profile is used for connecting panels together. Modesty

panel shall be made of 18mm Thick Pre-laminated twin board of E1-P2 grade Edge

Conferen banded with matching 2 mm thick PVC lipping. An array of panels made of 0.8mm and

ce Room 1.2 mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used

for flow of wires and cables. Cutout for Standard Anchor Roma 4 module is provided for

electrical fittings in Straight two seater and single seater modules below access flap per

seat. The table is equipped with Extron cables cubbies along with cable retractors as

standard offering only for 1800mm head module, 2350mm head module, 150° head

module and 165° head module. For straight two seater and single seater modules,

provision to mount AV cables is provided (eg. HDMI,VGAA, etc). Only Corner 90°, 30°

corner and 50° corner modules have provision for wire flow between adjacent tables.

Additional Wirecover made of 0.8mm Thick CRCA, provided below worktop to conceal

Microphone wires running from table top to wire tray.

Providing and Placing in Position High Back Chair. The cushioned seats shall be made of

injection moulded plastic outer and inner. Plastic inner shall be upholstered with pure

leather and moulded high resiliance polyurethane foamof Density = 45±2 kg/m³, and

hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6

cm W x 49.2 cm D. The back shall be cushioned and shall be made up of PU foam with

insitu moulded MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered

with pure leather. Back size shall be 47.5 cm W x 77 cm D. The armrest top shall be

moulded from polurethane, and shall be upholstered with pure leather and mounted on ot

a drop lift adjustable type tubular armrest support made up of Ø3.81±0.03 cm x

0.2±0.01 cm thick MS ERW tube having chrome plated finish. The armrest hieght shall

be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism shall be

Main designed with the following features : 360° revolving type, front-pivot for tilt with feet

Chair resting on ground and contionuous lumbar support ensuring more comfort, Tilt tension

adjustment can be operated in seating position, 5-position tilt limiter giving options of

variable tilt angle to the chair, seat/backtilting ratio 1:2, the mechanism housing is made

up of HPDC aluminium black powder coated. Seat depth adjustment shall be integrated in

the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5

cm. Back frame shall be connected to the up/down mechanism housed in plastic T spine.

It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit

individual need. the pneumatic height adjustment shall have an adjustment stroke of

10±0.3 cm. The pedestal shall be high pressure die cast polished aluminium and fitted

with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre dia. 5

nos. of twin wheel castors shall be injection moulded in plastic having 6.0±0.1 cm wheel

Providing and Placing in Position Midand assembled

Back Chair. Theto overall

dimensions shall be 76.1cm

x 76.1cm x 96.5-114cm. Seat height shall be 44.5cm - 54.5cm. The cushioned seats

shall be made of injection moulded plastic outer and inner. Plastic inner shall be

upholstered with pure leather and moulded high resiliance polyurethane foamof Density

= 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression.

Seat size shall be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be

made up of PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x

0.16±0.0128 cm, upholstered with pure leather. The armrest top shall be moulded from

polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift

adjustable type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick

MS ERW tube having chrome plated finish. The armrest hieght shall be adjustable upto

Meeting 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism shall be designed with the

Chair following features : 360° revolving type, front-pivot for tilt with feet resting on ground

and contionuous lumbar support ensuring more comfort, Tilt tension adjustment can be

operated in seating position, 5-position tilt limiter giving options of variable tilt angle to

the chair, seat/backtilting ratio 1:2, the mechanism housing is made up of HPDC

aluminium black powder coated. Seat depth adjustment shall be integrated in the seat

through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back

frame shall be connected to the up/down mechanism housed in plastic T spine. It can be

adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual

need. the pneumatic height adjustment shall have an adjustment stroke of 10±0.3 cm.

The pedestal shall be high pressure die cast polished aluminium and fitted with 5 nos. of

twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin

wheel castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter

Providing and Placing in position Visitors. The cushioned seats shall be made of injection

moulded plastic outer and inner. Plastic inner shall be upholstered with pure leather and

moulded high resiliance polyurethane foamof Density = 45±2 kg/m³, and hardness load

16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6 cm W x 49.2

23 cm D. The back shall be cushioned and shall be made up of PU foam with insitu moulded Each 13 37,538.00 487,994.00

MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with pure

leather. Back size shall be 47.5 cm W x 77 cm D. The tubular frame shall be cantilever

type and made of Ø2.54±0.03 cm x 0.2±0.016 cm thick SS 202 tube. The back shall be

connected to the frame through chrome plated high pressure die cast connector piece.

Supplying and Placing in place of 3 seater sofa. The overall dimensions of the sofa shall

be 2060W x 905D x 855H. The seat should be made of PU foam with Density 28 ± 2

kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu.

Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should

Visitor be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of

24 Lounge supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Each 2 42,297.00 84,594.00

Sofa Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also

shall be resistance and termite proof as per IS:303.) and pinewood of cross section

deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring

assembly is mounted over understrucrure for cushioning effect. It should be a welded

assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes

Center made in SS 202 grade for fixing with understructure. It shall be a welded assembly

Table made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table

shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes

Side made in SS 202 grade for fixing with understructure. It shall be a welded assembly

Table made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table

shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm.

Providing and placing workstations for Work pool area. The overall dimensions of the

configuration shall be 2100mm x 2550mm x 1650mm. The size of the worktop shalll be

1800mm x 750mm made from prelaminated particle board. The credenza shall have

dimensions 450mm depth. The length shall be 2550mm which shall comprise of 2

seaprate modules 1800mm L and 750mmL. It consists of overhead storage, shelf and a

fabric magnetic screen. The wooden panels in this hutch is made from 18m thk PLB of E1-

P2 grade with machine pressed 2mm thk and 0.8mm thk PVC edge band glued on the

edges. Bumpers are provided in the overhead storage for noiseless and smooth closing.

The Legs assemblies are fabricated MS Tube of section MS ERW Tube 40mm x 20mm x

1.2mm thick, top connector of 2.5 mm thick MS plate, Support channel of 2.5 mm thick

MS plate and leg frame top stiffener of 0.8 mm thick. The base of the MS tube fitted with

Cabin a Leveler plate assembly over which an M8x60L Leveler is fitted. This leveler allows for

27 adjustment of the height by 50 mm. The cross members are made from 40x20x1.2 thk Each 50 112,893.00 5,644,650.00

M.S. tubes. The typical credenza includes features like CPU storage mechanism, drawers

and wire raisers. Drawer system includes top drawer and bottom drawer. The drawer

wooden panels are made from 18mm thk PLB of E1-P2 grade machine pressed with

0.8mm and 2mm thk PVC edge band. Drawer bottom panel is made from 0.8mm thk

CRCA and is powder coated with Epoxy Polyester. Side covers: Side cover assembly is

made of 2 mm thick M.S sheet. The assembly is powder coated with Epoxy Polyester.

understructure: it is made of 40x20x1.2 thick tubes which are powder coated with Epoxy

Polyester. The cross members are used for supporting worktops. These are made from

40x20x1.2 thk M.S. tubes. Modesty shall be made from 2mm thk HR with 4no. 0f M6

bush welded to it for fixing purpose. A perforation pattern is laser cut giving it a elegant

look. Legss assembly supports the worktop on one side other other side being supported

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of

injection moulded glass filled nylon & upholstered using net fabric with high tenacity

yarn. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with

density =55+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25%

compression. The armrest has an up=Down adjustment of 8.5 ± 0.5cm which is provided

in armrest structure. Armrest top has an integrated layer of thermoplastic elastomer.

Armrest is made up of plastic injection moulded nylon with textured top. It shall have

Main Front pivot synchro mechanism with following features. 360 degree revolving type, Single

Chair point control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock

feature, seat/back tilting ration of 1:2. The lumber support consists of polypropylene pad

with mouled polyurathene foam & covered with polyester fabric. The height of lumber

pad can be adjusted through two projecting knobs provided on the rear side of the pad.

Lumber pad has an adjustment of 8.0± 0.5 cm in height. The must be greenguard

certified. the work shall be carried out as per guidance and instructions recieved from

Engineer Incharge. This shall come along a headrest from same family. It shall be SCS

IAQ certified for Indoor Air Quality.

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of

injection moulded glass filled nylon & upholstered using net fabric with high tenacity

yarn. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with

density =55+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25%

compression. The armrest has an up=Down adjustment of 8.5 ± 0.5cm which is provided

in armrest structure. Armrest top has an integrated layer of thermoplastic elastomer.

Armrest is made up of plastic injection moulded nylon with textured top. It shall have

29 Front pivot synchro mechanism with following features. 360 degree revolving type, Single Each 100 11,957.00 1,195,700.00

point control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock

feature, seat/back tilting ration of 1:2. The lumber support consists of polypropylene pad

with mouled polyurathene foam & covered with polyester fabric. The height of lumber

pad can be adjusted through two projecting knobs provided on the rear side of the pad.

Lumber pad has an adjustment of 8.0± 0.5 cm in height. The must be greenguard

certified. the work shall be carried out as per guidance and instructions recieved from

Engineer Incharge. It shall be SCS IAQ certified for Indoor Air Quality.

Worktop shall be made from 25mm thick MDF one side prelaminate board with 0.4mm

PVC membrane pressed on to top and having chamfered edge. Soft closing dual access

flap provided for access to power supply and data cables. The Under-structure consists of

mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved

30 shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC Each -

lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for

improving the aesthetics.The product has a knock-down construction. A wire raiser made

of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60 microns) for

flow of wires and cables. A Power box with 2 cutouts on either sides for standard 8

module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is

provided for mounting Audio Visual Cables(eg. HDMI,VGA-A,etc).

31 Meeting Table size- 4200mm x 1500mm x 740mm Each 3 115,698.00 347,094.00

32 Meeting Table size- 3000mm x 1150mm x 740mm Each 2 61,083.00 122,166.00

33 Meeting Table size- 2350mm x 1150mm x 740mm Each 7 45,991.00 321,937.00

Providing and Placing in position High Back Chair. The seat shall be made up of 1.2 +/-

0.1 cm thick hot pressed plywood & upholstered with synthetic leather and moulded

polyurethane foam. The dimensions of seat should be 49.0cm(W) x 51.4(D) and that of

back should be 51.8cm(W) x 75.2cm(H). High Resilience (HR) polyurethane foam should

be used in making seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and

hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression.The adjustable armrests

are designed with up-down adjustment in 8 steps(8.0+/-0.5 range). The height

adjustable armrest structure is chrome plated and fitted with PU moulded over metal

insert fixed armrest top. The mechanism of the chair shall have following features : 360⁰

Main revolving type, Single point control, Tilt tension adjustment, 4 position locking with

Chair antishock feature, seat back tilt ratio 1:2, front pivot for tilt with feet resting on ground

ensuring more comfort. The Back can be adjusted in 5 positions manually. Stroke of

height adjustable spine is 7 cm. The chair shall be provided with pneumatic height

adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal is High Pressure Die

cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ±

0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors).The twin wheel castors are

injection moulded in black PP. Seat can be slide horizontaly as per user convienience.

Stroke of seat slide is 5 cm. Overall dimensions of Chair shall be, Width of Chair -

67.5cm, Depth of Chair - 67.5cm as measured from pedestal below. Height from ground -

min 102.0 to max 119.0cm. Seat height - min 45.0 to max 55.0cm.

The seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed plywood & upholstered

with synthetic leather over moulded polyurethane foam. The dimensions of seat should

be 49.0cm(W) x 51.4(D) and that of back should be 51.6cm(W) x 65.7cm(H). High

Resilience (HR) polyurethane foam should be used in making seat & back which shall be

moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for

25% compression.The adjustable armrests are designed with up-down adjustment in 8

steps(8.0+/-0.5 range). The height adjustable armrest structure is chrome plated and

fitted with PU moulded over metal insert fixed armrest top. The mechanism of the chair

shall have following features : 360⁰ revolving type, Single point control, Tilt tension

Meeting adjustment, 4 position locking with antishock feature, seat back tilt ratio 1:2, front pivot

Chair for tilt with feet resting on ground ensuring more comfort. The Back can be adjusted in 5

positions manually. Stroke of height adjustable spine is 7 cm. The chair shall be

provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm.

The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin

wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With

castors).The twin wheel castors are injection moulded in black PP. Seat can be slide

horizontaly as per user convienience. Stroke of seat slide is 5 cm. Overall dimensions of

Chair shall be, Width of Chair - 67.5cm, Depth of Chair - 67.5cm as measured from

pedestal below. Height from ground - min 92.0 to max 110.0cm. Seat height - min 45.0

Providing and placing workstations for Work pool area. The overall dimensions of the

configuration shall be 1950mm x 1800mm x 1200mm. The size of the worktop shalll be

1650mm x 750mm made from prelaminated particle board. It shall also have side

credenza with shelf mounted on it with panels as per layout. The credenza shall have

dimensions 450mm depth. The typical credenza includes features like CPU storage

mechanism, drawers and wire raisers. Drawer system includes top drawer and bottom

drawer. The drawer wooden panels are made from 18mm thk PLB of E1-P2 grade

machine pressed with 0.8mm and 2mm thk PVC edge band. Drawer bottom panel is

made from 0.8mm thk CRCA and is powder coated with Epoxy Polyester. Shelf shall be

provided for active storage contents. Its top and bottom panels are made from 18mm thk

Prelaminated particle board of E1-P2 grade. Side covers are made from 2mm thk CRCA.

Workstati Shelf support assembly is made from 40x20x1.2mm thk tubes. Shelf is mounted on

36 on Type Credenza using M6 screws. Legss assembly supports the worktop on one side other Each 75 82,915.00 6,218,625.00

1 other side being supported by credenza. The legs are fabricated by CO2 welding MS tube

of section MS ERW tube 40mm x 20mm x 1.2mm thk, top connector of 2.5mm thk HR.

Support channel of 2.5mm HR and leg frame top stiffener of 0.8mm CRCA with base of

MS tube fitted with a leveller fix plate assembly. Partition thickness as 52.4 mm thk

and ht - 1200 including powder coated aluminium trims. Tiles: Combination of top

tiles are fabric magnetic/fabric/fabric tackable/white board/glass writing board/ clear

glass tile/ plain metal/ prelam tile. Bottom tiles - Plain metal/ fabric magnetic /

fabric / laminated /prelam. The panel thickness comprises of 38mm (35 mm Minimum)

thick paper honeycomb + 3mm MDF on each sides + 0.6mm decorative laminate or

fabric on both sides. The uprights and horizontals shall be made of aluminium extrusion

having average wall thickness of 1.2 mm & powder coated with epoxy- polyester

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of

injection moulded glass filled nylon & upholstered using net fabric with high tenacity

yarn. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with

density =55+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25%

compression. The armrest has an up=Down adjustment of 8.5 ± 0.5cm which is provided

in armrest structure. Armrest top has an integrated layer of thermoplastic elastomer.

Workstati Armrest is made up of plastic injection moulded nylon with textured top. It shall have

37 on Main Front pivot synchro mechanism with following features. 360 degree revolving type, Single Each 80 11,957.00 956,560.00

Chair point control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock

feature, seat/back tilting ration of 1:2. The lumber support consists of polypropylene pad

with mouled polyurathene foam & covered with polyester fabric. The height of lumber

pad can be adjusted through two projecting knobs provided on the rear side of the pad.

Lumber pad has an adjustment of 8.0± 0.5 cm in height. The must be greenguard

certified. the work shall be carried out as per guidance and instructions recieved from

Engineer Incharge. It shall be SCS IAQ certified for Indoor Air Quality.

Providing and placing workstations for Work pool area. The overall dimensions of the

configuration shall be 1350mm x 1800mm x 1200mm. The size of the worktop shall be

1200mm x 750mm made from prelaminated particle board. The credenza shall have

dimensions 450mm depth and 1800m length. The typical credenza includes features like

CPU storage mechanism, drawers and wire raisers. Drawer system includes top drawer

and bottom drawer. The drawer wooden panels are made from 18mm thk PLB of E1-P2

grade machine pressed with 0.8mm and 2mm thk PVC edge band. Drawer bottom panel

Workstati is made from 0.8mm thk CRCA and is powder coated with Epoxy Polyester. Worktop

38 on Type support assembly is made from 2.5mm tk HR . Worktop cross members are fitted on it Each 120 56,584.00 6,790,080.00

2 with help of M6 screws. Screens are either Fabric magnetic Screens made from either

18mm thk PLB of E1-P2 grade with 0.5mm thk GI sheet stuck on it or Laminateed glass

screens of overall 8mm thickness with 1mm PVB film stuck in between. Side covers: Side

cover assembly is made of 2 mm thick M.S sheet. The assembly is powder coated with

Epoxy Polyester. Legss assembly supports the worktop on one side other other side

being supported by credenza. The legs are fabricated by CO2 welding MS tube of section

MS ERW tube 40mm x 20mm x 1.2mm thk, top connector of 2.5mm thk HR. Support

channel of 2.5mm HR and leg frame top stiffener of 0.8mm CRCA with base of MS tube

fitted with a leveller fix plate assembly. Screens are either Fabric magnetic Screens made

from either 18mm thk PLB of E1-P2 grade with 0.5mm thk GI sheet stuck on it or

Laminateed glass screens of overall 8mm thickness with 1mm PVB film stuck in between.

The cushioned seat and back assembly consists of seat base moulded in glass filled Poly-

amide, moulded polyurethane foam and upholstered with high stretch knitted polyester

fabric. The back size shall be 45.5cm W x 53.0cm H. The HR polyurethane foam used in

seat and back cushion is moulded in density 45kg per m3. The seat and back are firmly

connected to the base frame and are cantilevered in such a way that it gives a multi

dimensional movement possibility just with a simple lean on the sides or back, without

need for complex manual adjusments. The cantilevered seat offers impact cushioning

while seating and synchronises with the back movement during posture changes. The ‘S:

Workstati shaped spines moulded in high strength glass filled Polyamide and the spine connector

on Chair moulded in glass filled Polyamide form the back spine structure involved in multi

dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3

position Tilt limiter feature which is inbuilt in saet base and the tension is user weight

dependent. The adjustable armrests assembly consists of armrest housing sliding over

the armrest structure, both moulded in glass filled Polyamide. The pneumatic height

adjustment shall have a stroke of 9.2cm.The pedestal is injection moulded in glass filled

Polyamide and fitted with 5 nos. twin wheel castors. The pedestal is 66cm pitch centre

diameter and 76cm with castors. The overall dimensions of the chair shall be 76cmx

76cm x(99.5-108.8cm). The seat height shall be (44.5-53.8cm).

The cushioned seat and back assembly consists of seat base moulded in glass filled Poly-

amide, moulded polyurethane foam and upholstered with high stretch knitted polyester

fabric. The back size shall be 45.5cm W x 53.0cm H. The HR polyurethane foam used in

seat and back cushion is moulded in density 45kg per m3. The seat and back are firmly

connected to the base frame and are cantilevered in such a way that it gives a multi

dimensional movement possibility just with a simple lean on the sides or back, without

need for complex manual adjusments. The cantilevered seat offers impact cushioning

while seating and synchronises with the back movement during posture changes. The ‘S:

Receptio shaped spines moulded in high strength glass filled Polyamide and the spine connector

n Chair moulded in glass filled Polyamide form the back spine structure involved in multi

dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3

position Tilt limiter feature which is inbuilt in saet base and the tension is user weight

dependent. The adjustable armrests assembly consists of armrest housing sliding over

the armrest structure, both moulded in glass filled Polyamide. The pneumatic height

adjustment shall have a stroke of 9.2cm.The pedestal is injection moulded in glass filled

Polyamide and fitted with 5 nos. twin wheel castors. The pedestal is 66cm pitch centre

diameter and 76cm with castors. The overall dimensions of the chair shall be 76cmx

76cm x(99.5-108.8cm). The seat height shall be (44.5-53.8cm).

Receptio Provifing in place of dining chairs of following specifications. Dimension of the chair shall

41 n sofa be 875mm(H) x 535mm(D) x 470mm(W). Seat and Back Upholstery shall be PU Grey Each 13 19,486.00 253,318.00

seating Color. Chair Legs shall be Solid Rubberwood.

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes

made in SS 202 grade for fixing with understructure. It shall be a welded assembly

made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table

shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm.

Supplying and Placing in place of 3 seater sofa. The overall dimensions of the sofa shall

be 2060W x 905D x 855H. The seat should be made of PU foam with Density 28 ± 2

kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu.

43 Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should Each 4 42,297.00 169,188.00

be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of

supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.

Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also

Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall

be 860W x 905D x 855H. The seat should be made of PU foam with Density 28 ± 2

kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu.

44 Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should Each 6 30,659.00 183,954.00

be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of

supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.

Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes

Center made in SS 202 grade for fixing with understructure. It shall be a welded assembly

Table made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table

shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes

Side made in SS 202 grade for fixing with understructure. It shall be a welded assembly

Table made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table

shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm.

Main Body: (a) Construction: Rigid Knock Down construction made of 0.8 thk. CRCA

Steel. Each unit has 5 loading levels formed by 4 nos. adjustable shelves. The body

comprises the following components: Front Cover: It is the foremost panel of the body on

which the Drive unit are fixed. It is made of 0.8 thk. CRCA Steel. The front cover has a

pattern of holes on the front surface for ventilation purpose. Back Cover: It is the

backmost panel of the body and is the mirror image of the front cover. It is made of 0.8

thk. CRCA Steel. The back cover has

a pattern of holes on the surface for ventilation purpose. Back Panel: The back panels are

made of 0.6 thk. CRCA Steel. The two back panels are fixed together using machine

screws. When the entire optimizer layout is locked it also prevents access to inside files

from the outside. Shared Panel: The shared panel acts as a partition between two

Compact adjacent bodies. It is made of 0.8 thk. CRCA Steel. Optimizer Height from ground is 2083

47 mm (1980 body + 65 undercarriage + 38 channel system). Overall size of one bost shall Each 100 30,463.00 3,046,300.00

be 1200mm W x 400mm D. The bodies including shelves are given antirust surface

treatment & are coated with epoxy polyester powder. It involves an 8-step treatment.

Final finish consists of epoxy polyester powder coating of approved color & shade with a

Dry Film Thickness of minimum 40 microns. Shelf: It is made of 0.7 thk CRCA steel

conforming to IS: 513 Gr.D or DD. Its max load bearing capacity is 100 Kg uniformly

distributed per shelf. Shelves are mounted on support brackets & shelf level can be

adjusted at approx. 25.4 pitches. Storage capacity:- The shelf is 1180mm in length and

can hold up to 13 nos. of box files of size 85mm x 345mm x 285mm. Drive Type

Understructure:- The Understructure is a welded frame suitably fabricated to bear the

loads based on configuration. The frame consists of the following parts: Main channel,

body-fixing channel, U-channel and Z-channel. All the components are made of HR sheet

The overall dimensions of the top shall be 900mm dia. x 720mm. The Worktop is made of

a 25mm thick MDF OSR with PU painting on top side. Understructure: It should consist of

an inner tube assembly with top plate, for worktop mounting, & an outer tube assembly

with round/square bottom plate. The inner and outer tube asemblies are telescopically

connected. The top plate is made of 5mm thk HOT ROLLED steel plates (HR) (As per

IS:2062) & the bottom plate is made of 8mm thk HOT ROLLED steel plates (HR) ( As per

Café IS: 2062). The inner tube assembly is made of dia 82.5 X 2thk ROUND ELECTRIC

Table RESISTANCE WELDED tubes (ERW) ( AS per IS:7138) and 8mm thk HOT ROLLED Steel

plate (HR) (As per IS:2062) welded together using tungsten inert gas welding. The outer

tube assembly is made of dia 89 X 2.5thk ROUND ELECTRIC RESISTANCE WELDED

tubes (ERW) ( AS per IS:7138) and 8mm thk HOT ROLLED Steel plate (HR) (As per

IS:2062) welded together using tungsten inert gas welding.The whole structure is EPOXY

POLYSTER powder coated (DFT 40-60 microns). The product has a KD construction. It is

assembled using alloy steel hardware( Blackened and coated with rust oreventive oil).

Provifing in place of dining chairs of following specifications. Dimension of the chair shall

49 be 875mm(H) x 535mm(D) x 470mm(W). Seat and Back Upholstery shall be PU Grey Each 27 19,486.00 526,122.00

Color. Chair Legs shall be Solid Rubberwood.

Providing and placing ALL WOOD HINGED DOOR UNIT (HDU). Construction & Material

Knockdown construction. Door Opening Twin door with self closing hinges of Wood made

from18mm Thick Pre Laminated Board. Handle · Aesthetically appealing recessed plastic

handle for& wooden Doors. Locking Mechanism Cam lock · 3 point locking mechanism in

Wood Door Shelving · Height wise Adjustable Shelf Mounting. Wooden Top shall be be

50 Storages made from Pre-Laminated Board of 25 mm thk. Skirting of 125 mm High shall be Each

provided. Leveler Screw type adjustable Leveler with plastic base. height. Back Panel

and Sides of the storageunits will be made out from 18mm thick Pre-Laminated Particle

Board. Note: All partitions and side panels have levelling screws for adjustment in case of

Uneven floor to take care of +/- 10mm of uneven flooring. The work shall be carried out

as per guidance and instructions received from engineer incharge.

52 Size- 750mm x 450mm x 900mm + provision for plant holders. Each 43 19,556.00 840,908.00

53 Size- 900mm x 450mm x 900mm + provision for plant holders. Each 8 23,050.00 184,400.00

54 Size- 1050mm x 450mm x 900mm + provision for plant holders. Each 7 25,771.00 180,397.00

SCHEDULE OF QUANTITIES - HVAC WORKS

S. No. DESCRIPTION UNIT QUANTITY RATE DSR (INR) NON-DSR (INR)

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant

Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating,

having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors

for above 14 HP modules, microprocessor based Controller, top discharge type condensing

unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as

1 1 required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C per HP 30.00 16415.00 492450.00

ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3

Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and

ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not

less than 6.5 .

Supply,installation,testing and commissioning of following minimum capacity VRV/VRF High

wall type Indoor unit equipped with washable synthetic media pre-filter,fan section with low

noise fan/ dynamically balanced blower, multi speedmotor ,coil section with DX copper coil,

electronic expansion valve, outer cabinet ,cordless remote control,drain pan,necessary

accessories etc., suitable for operationon 230V±10%, 50Hz, single phase AC supply,complete

as required. The unit shall have automatic force shutdown provision in case of fire on receiving

signal from BMS System.The cooling capacity of indoor unit will be at air inlet conditions of

27Degree C DB and 19 Degree C WB temperature.

Lifting, Shifting, Supply, Installation, Testing & Commissioning of Interconnecting "Y" & "T"

3 Joints i.e. Refnet Joints/Header with Insulation for refrigearnt piping

4 5 Refrigerant Piping

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing

of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system,

complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing

including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell

elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for

Suction and Liquid lines, all accessories as per specifications etc. as required :

4.1 5.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 60.00 245.00 14700.00

4.2 5.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 300.00 331.00 99300.00

4.3 5.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 60.00 466.00 27960.00

4.4 5.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 300.00 588.00 176400.00

4.5 5.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 50.00 707.00 35350.00

4.6 5.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 50.00 865.00 43250.00

4.7 5.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 25.00 1022.00 25550.00

4.8 5.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 25.00 1108.00 27700.00

5 Cable/Wiring

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

1.14 insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit

6 DSR (E & M - 2018) Cable Trays with Covers

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray

(Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in

4.6 convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders

including G.I. bolts & nuts, etc. as required.

6.1 4.6.8 300 mm width X 62.5 mm depth X 2.0 mm thickness meter 20.00 1085.00 21700.00

6.2 4.6.10 450 mm width X 62.5 mm depth X 2.0 mm thickness meter 20.00 1440.00 28800.00

7 Drain Piping

Supply,installation,testing and commissioning of PVC drain water with necessary clamps,

MR fittings such as bends tees etc. and duly insulated.

Total HVAC- VRV WORKS 1595620.00 262119.00

GRAND TOTAL 1857739.00

GRAND TOTAL 1857739.00