SPECIAL REPAIR TO ROOF TOP FALSE CEILING AND OTHER MISC WORK IN BLDG NO T-75 and SPECIAL REPAIR OF ROAD AND DRAINAGE OF ROBERT BARRACK (KRISHNA ENCLAVE) OF HQ MB AREA UNDER GE (WEST) JABALPUR

Amount

Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness incl part chipping (below or above ground level) complete and removing debris from the premises.

Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed.

Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

Dismantling of wall and ceiling boards of any description (fibre, pulp, insulation, etc.) including cover fillets complete all as specified and directed including removing to store complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling of timber scantlings unframed 40Sq Cm and over in section, in any position complete all as specified and directed.

Dismantling of plain/ corrugated AC/Steel Roof sheeting of any description including stacking and removing to store complete.

Dismantling of single layer Mangalore pattern or similar tiles in roofing including stacking and removing to store complete.

Dismantling of battens for tiles, shingles etc, of any description including tilting fillets spaced exc 15 cm and removing to store complete.

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for PCC (1:2:4) type B1 (using 20mm graded stone aggregate) in copings, kerbs, and the like all as directed incl necessary form work complete all as specified and directed.

M&L for Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed.

M&L Brick work using fly ash old size bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

Ditto all as per item No 34 above items but except brick ( obtained from dismantling of brick work ) complete all as specified and directed.

M&L for Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

M&L for Cutting holes in brick walls exc 1/2 brick & n exc full brick built in cement mortar for inserting hold fasts, cutting and preparation of brick wall for insertion of doors, windows & ventilator and making good dismantled portion in cement mortar 1:3 etc complete all as specified and directed.

Taking down chowkats or frame with shutters of any description (without taking off shutters from the frames) n. exc 1.5 Sqm each including removing to store complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutters from the frames) exc 1.50 sqm but n exc 4 sqm each including removing to store complete all as specified and directed.

S&F for second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F for 35mm thick second class hard wood factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc divided into squars with plain chamfered or rounded mitred and rebated sash bars any numbers and fitted to chowkats as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed.

S & F 30 mm thick flush door shutter, solid core construction with block board core and ply wood face panels commercial type on both side complete all as specified and directed.

S & F for wood grain printed colour PVC laminate sheet 2mm thick fixed or laid on to flush doors by using rubber based adhesive, supplying & fixing at site as per specification complete as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed.

S&F for 150 mm Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

S&F for Extruded brass handles, fabricated type polished of size 150 mm complete all as specified and directed.

S & F 100 mm Butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-11 and fixed complete all as specified and directed.

S&F for 300mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed and fixed complete all as specified and directed.

S&F mild steel, 300 mm long brass helical door spring incl roller and roller plate complete all as specified and directed.

S&F 60 mm long brass Floor door stopper of aluminium alloy body and tongue anodised with hard steel spring ,fixed in floor complete

S&F stainless steel wire cloth 0.40 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.40 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified and directed

S&F for double action floor door spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed to aluminium door etc. complete all as specified and directed.

S&F for door closer hydraulically regulated designation No-2 universal type of aluminium body (extruded section) fixed to door frames with screws or by welding suitable for door shutters of 701-805 mm in width & wt between 36-60 kgcomplete all as specified and directed by Engr-in-charge.

M&L for MS flat iron work as in wind ties for roof including securing bolts, drilling holes, notching for wire etc complete all as directed.

M&L, Rolled sections as in main and cross beams, hip and jack rafters;etc where connected to common rafters and running rails fixed with angle cleats or other connecting plates (Fe-410- W(Gde- E-250) quality-B) complete all as specified and directed.

S&F steel work in tubular section for roof manglore tile including special shaped washer etc complete using ERW or induction but welded tubes confirming to I.S. 1161-1979 grade St. 240 etc complete all as specified and directed.

M&L Framed work as in doors or gates of angle or other section (MS profile box type section for door frame) Fe- 290 (Gde E- 165) with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

Taking down aluminium door shutter exc 1.0 Sqm not exc 2.0 sqm each including floor door closer, removing glass with beading before taking down and refixing of glass, beading and floor door closer after replacing broken parts of aluminium shutter including easing of shutter complete all as specified.

M & L for Roof tiles, Mangalore pattern, interlocking at side joints, laid dry and fixing with screw at eaves end complete all as specified and as directed.

Refixing of old manglore Roof tiles, Mangalore pattern, interlocking at side joints, laid dry and fixing with screw at eaves including cleaning for refixing complete all as specified and as directed.

S&F for 0.63 mm Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm (AZ-150) of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified

M&L for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm (AZ-150) of an colour having tensile strength of 550 Mpa as in roof covering/cladding/ ridge to wall, fixed with self tapping screws complete all as specified and directed.

Taking down of eaves gutter,rain water pipes , AC/PVC pipes of any size or pattern including all fittings etc complete all as specified and directed.

M&L for non skid ceramic coloured joint free tiles 7-8 mm thick area of each tile exceedeing 0.18 sqm but n.exc 0.38 sqm (600x600), in floors, set and jointed in neat cement slurry and pointed in white cement to over and including 15 mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L for Vitrified Ceramic tiles dark shade ( Matt finish ) 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L for Vitrified Ceramic tiles dark shade ( Matt finish ) 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, as in vertical surfaces such as skirting / dado set and jointed in neat cement slurry and pointed in white cement to over and including 10 mm thick backing in CM (1:4) complete all as specified and directed.

M&L for Polishing the existing old kota stone flooring including preparation, grinding and polishing in floors complete all as specified and directed.

M&L for Glazed ceramic tiles of size 600x1200x 7mm thick in vertical surfaces such as dado/ skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 all as specified.

M&L for Glazed ceramic tiles of size 300x600 7mm thick in vertical surfaces such as dado/ skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 all as specified.

M&L 25 mm thick cement concrete (1:2:4), type B-0, (using 12.50 mm graded aggregate) as in floors including finishing the surface rough & even for receiving kota/tiles complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate, 75mm thick in plinth protection laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified and directed.

M & L for 20 mm thick Granite Stone (Black/Ruby Red ) work (table rubbed and polished) as in Cill/Jamb of Door/window, cooking platforms incl edge moulding & cutting holes for gas pipe through drill machine and jointed with grey cement slurry and pointed to match the shade of granite stone including Screed bed 15 mm thick in CM (1 : 6) complete all as specified and as directed.

M&L 75 mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in floor sub base and finished even and fair complete all as specified and directed.

M&L for rounding to edges of granite stone slabs one edge, such as in cooking platform, and other similar situations all as specified and as directed.

M&L for machine cut cudappa stone slab 20 to 25 mm thick over and including cement screed base 15mm thick in CM 1:6 in floors and DP for granite laid and jointed with grey cement slurry mixed with pigment complete all as specified and directed.

Taking down cement plaster on wall/ceiling/roof etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed.

M&L for 15 mm thick rendering in CM (1:6) on fair faces of bk /concrete surfaces including finishing even and smooth (without using extra cement ) complete all as specified and as directed.

M&L for 15 mm thick rendering in CM (1:4) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement or as per manufacturer's instructions and finished the surfaces even and smooth without using extra cement complete all as specified and directed. Note : Liquid WPC will be measured and paid separately.

M&L 5 mm thick rendering in CM (1:3) on concrete/Ceiling surfaces and finishing even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered surface of walls and applying a coat of primer over 2mm thick wall care putty complete all as specified and directed.

M&L for Complete removal existing treatment by scraping/sanding or any other method and preparation of old surfaces of walls and applying coat of Primer over 2 mm thick birla wall care putty on walls complete all as specified and directed.

M&L for applying two coats of Acrylic Emulsion paint any colour on walls complete all as specified and directed.

M&L for preparing new plastered surfaces of walls and applying two coats of oil bound distemper any tint with 2mm thick wall care putty over a coat of primer on walls complete all as specified and directed.

M&L for complete removal existing treatment of any description and preparation of old surfaces of walls and applying two coats of oil bound distemper any tint with 2mm thick birla wall care putty over a coat of primer on walls complete all as specified and directed.

M & L for preparation of new plastered wall surface and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over 2mm thick water proof wall care putty complete all as specified and as directed.

M&L for Complete removal of existing treatment of any description and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over and including 2mm thick water proof wall care putty complete all as specified and as directed.

M&L for preparation of old decorated surface of ceiling and applying two coats of white wash complete all as specified and as directed.

M&L for Prepration of newly plastered surfaces and applying three coat of white wash on ceiling complete all as specified and as directed.

S& F 5 mm thick sheet glass ordinary quality and glazing with oil putty/wooden beading in square n. exc 0.5 Sqm in each pane complete all as specified and directed.

S & F 3 mm thick figured glass pin head type and glazing with oil putty/wooden beads in squares n exc 0.5 Sqm in each pane etc complete all as specified and directed.

M&L for applying two coats synthetic enamel paint over a coat of pink primer including prepartion of new wooden or wooden based materials of any description not other described over 10cm in width or girth complete all as specified and as directed

M & L preparation of new steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat of red oxide/Zinc Chrome primer complete all as specified and as directed.

M&L Preparing old wooden surfaces exc 10Cm in width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L Preparing old steel surfaces exceeding 10Cm in width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

Taking down steel tubing and connections including cleaning for refixing or removal from site for 15mm bore pipe all as specified and as directed.

Taking down steel tubing and connections including cleaning for refixing or removal from site for 20 mm bore pipe all as specified and directed by Engr-in-charge.

Taking down steel tubing and connections including cleaning for refixing or removal from site for 25 mm bore pipe all as specified and directed by Engr-in-charge.

S&F for 25 mm CPVC pipes SDR 11 with fittingsfixed with solvant on walls/ceiling or laying in floors including Brass threaded fittings for fixing taps etc complete all as specified and directed.

S&F for 20mm CPVC pipes SDR 11 with fittings fixed with solvant on walls/ceiling or laying in floors including Brass threaded fittings for fixing taps etc complete all as specified and as directed.

S&F in repair PVC connection 15 mm dia and 450 mm long with 2 Nos check nuts with washer complete all as specified and as directed.

S&F in repair 15mm bore stop valve/ angle valve fancy type chromium plated cast copper alloy screwed down high pressure screwed both ends for iron pipe or for union complete.

S&F, PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in walls complete all as specified and directed.

S&F, PVC (SWR) pipes 150 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in walls complete all as specified and directed.

S&F, in repair PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in walls complete all as specified and directed.

S&F PVC (SWR) bends ISI marked any radius of 110 mm bore with access door complete all as specified and directed.

S&F PVC (SWR) bends ISI marked any radius of 75 mm bore with access door complete all as specified and directed.

S&F in repairs PVC (SWR) junction single, (single T) equal or un equal of 110 mm bore of pipe complete all as specified and directed

S&F in repairs PVC (SWR) junction single, (single T) equal or un equal of 75 mm bore of pipe complete all as specified and directed

S&F PVC (SWR) vent cowl 110mm bore complete all as specified and directed.

S&F PVC (SWR) nahani/ floor trap, plain with grating with or without waste hole including jointing with solvent cement 75mm dia outlet complete all as specified and directed.

S&F in repair brass chromium plated shower rose 125 mm size with or without swivel joint complete all as specified and directed.

Dismantling water tanks capacity exc 250 Ltr and n exc 500 Ltr and removing from site complete all as specified and directed.

S&F rotational molded polyethylene water storage tanks (cylindrical vertical with closed top) capacity 500 Ltr , ISI Marked, hoisted and fixed in position all as specified and directed.

S&F Ball valves 20 mm dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) complete all as specified and directed.

S&F in repair gun metal, globe or gate valve for 25 mm bore pipe with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F in repairs vitreous China half stall urinal flat back with Spreader, waste fittings and outlet pipe complete with grating and union for discharge pipe (excluding flushing cistern flush pipe and waste pipe) including connections to flushing pipe and out going pipes etc complete all as specified and directed.

Providing & injecting chemical emulsion for Post Constructional Anti-termite (Chlorpyrifos 20 % EC) Treatment with external wall where the apron is not provided using chemical emulsion at the rate 7.5 liters per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavation channel along the wall and rodding etc. complete

Post Constructional Anti-termite (Chlorpyrifos 20 % EC) Treatment Along the external wall below concrete or masonry apron using chemical emulsion at the rate 2.25 liters per linear meter including drilling & plugging holes etc. in apron.

S&F Stainless steel Handles of senso (as per 3D designs) 150 mm inclduding all connection fitting as complete all as specified and directed and approved by GE.

S&F 30 mm flap Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed and approved by GE.

S&F, in repairs, 18mm thick ply, PVC sheet with prelaminated on one side of approved texture ("Celuca Ply of Rajshree make or equivalent in "Sintex" as approved by GE) as in Kitchen cabinet and cupboard etc (with shelves and partitions) including necessary fittings & fixtures as per manufacturer's instructions complete all as specified and directed.

S&F in repairs Wall hung Pedestal water clost with UF soft close seat cover, hinges, accessories set, size 385 X 595 X 385mm including all fittings complete all as specified and directed.

S&F for single piece slim concealed flushing cistern with wall mounting frame , installation kit and "S-type drain pipe connection set for wall hung Water closet including all fittings complete all as specified and directed.

S&F for flush control plate for concealed flushing cistern including all fittings complete all as specified and directed.

S&F for metropole flush valves dual flow 32mm size ( concealed body) with exposed shut off provision and 100mm square plate (3.0 / 6.0 ltr per flushing ) including control cock and operating lever including all fittings complete all as specified and directed.

M&L for crack repairing by Providing 6mm dia u dowel bar 20cm on either side of crack and fixed with CM (1:3) @ 600 mm c/c and filling crack by epoxy putty into Brick crack after opening up RCC cracks in V– groove manner approximate 10 mm wide & 10mm deep using mechanical cutter, properly cleaning the same to remove loose dust dirt etc and filling the same using Nitocote VF –three component, solvent free, thixotropic, Epoxy resin based putty having 100% solid contents mixed density of 1.6 g/cc, compressive strength – 50 N/mm ², pot life of 40 minutes at 27 degree C, Drying time 8 hrs. recoatable time 24 hrs. And finishing in line and level with existing concrete surface etc. complete as per in charge GE. Make; - Thermax/ webac chemicals/ chemco system as approved by the GE. Note : (i) Quoted rate shall be deemed to be inclusive of materials all labours, tools and plants, scaffolding and working upto height 6 mtr etc. complete as per specification and directed by GE . (ii). Quoted rate deemed to be inclusive of materials & labours, tools and plants, scaffolding and working upto 6m height etc. complete as per specification and directed by GE. (iii) Adoption of necessary safety arrangements like safety belts ropes, helmets netting etc which are required for safety of worker working at height exceeding 3 mtr shall be mandatary and deemed to be inclusive in quoted rates.

M & L for snap grid false ceiling system of 4mm thick designer E board exposed suspended system, grid of size 600mm x 600mm compressing of GI powder coated Main Runner of dimensions 39mm x 24mm x 0.8 mm thick to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt-0.007 kg/clip), hold down clips (wt-0.0035 kg/clip), and fixed with pre painted 4mm thick E board of approved design and with provn for light fixture complete all as per manufacturer instructions and as directed.

S&F, in repair, chromium plated, Toilet paper holder complete all as specified and directed.

S&F, in repair, chromium plated, urinal spreader complete all as specified and directed.

S & F in repair 40 mm dia UPVC waste pipe of minimum length 1 mtr for Urinal, sink and WHB etc complete all as specified and directed.

Supply & Fixed in repairs Two way bib cock complete as specified and as directed.

M&L for Preparation of old/new surfacess of Manglore tiles/AC Sheets and applying two coat of Weather coat anti fungal & water repelent paint complete all as specified and directed.

S&F in repair Towel ring round with round flange complete all as specified and directed.

S&F, in repair, CP, soap dish holder complete all as specified and directed.

S&F, in repair, glass shelf with CP brackets and with decorative railing fixed to wall complete all as specified and directed.

S&F, in repair, Health Faucet with 1m PVC tube (stainless steel), chromium plated for vitreous china padestal pattern water closet complete all as specified and directed. Make as approved by GE.

complete removal of existing malamine polish and apply two coats of malamine polishing on wooden surfaces of any description, width or girth including cleaning and preparing the surfaces including a coat of wood filler on etc complete all as specified and directed.

S&F in repair for stainless steel chromium plated single lever basin mixer including all necessary fittings comlete all as specified and directed.

S & F coloured PVC insulation panels 7-8 mm thick cell type of 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S as per as per manucaturer intruction specification ( rates are inclusive of necessary frame work) complete all as specified and directed

S&F in repair Mortice lock,vertical type size 100 mm 4 lever suitable for aluminium door including fixing with stainless steel screw as complete all as specified and directed.

S&F in repair brass chromium plated bottle trap 32mm bore for wash hand basin with inlet & outlet screwed for pipes or connection incl necessary packing union and cap complete all as specified and directed by Engr-in-charge.

Supply & Fixed in repair for ceramic wash Basin counter top basin white colour of size 600 mm X 440 mmX150mm including table top counter for fixing WHB of matching colour complete all as specified and directed.

S&F in repair 25mm dia Stainless steel Curtain/dropary rod cut to required length and fix in position complete.

S&F in repair stainless steel Fency Nobs and 3mm thick bracket suitable for 25mm dia SS pipe complete all as specified and directed.

S&F in repairs for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement, complete all as specified and directed.

S&F for 12 mm thick Toughned glass as in hinged doors, partitions automatic doors and similar work including necessary arrangements ,cutting to shape, drilling holes required including packing with rubber gasket fixing with SS bracket and Pivot complete all as specified and directed.

S&F Stainless Steel handles suitable for Glass door shutters not less than 300mm long design/Make as approved by GE (ISI Mark) complete all as specified and directed

S & F Aluminium powder coated (minimum thickness of powder coating 50 micron) door with frame top and sides of size 83.50x44.45x1.62mm ( Section No 19549), and shutter top rail and stile of size 92 x 38 x1.70 mm ( Section No 21339) and Lock and bottom rail of size 125 x 37 x 1.80 mm ( Section No 19634) including rubber gasket, beading, anodised aluminium snap beading, screws, anodised aluminium fittings such as butt hinges/Pivot hinges 100 mm long (3 Nos.), handle (2 no.), Lock 06 Lever and locking arrangement ,fixing 5.00 mm thick glass with necessary rubber beading gasket etc including necessary plaster, painting ,cill and making good to disturbed portion all as specified and directed.

M&L for anodized aluminium powder coated (minimum thickness of powder coating 50 micron) three track sliding window (02 glass track and one wiremesh ) , frame side top and sides of size 92x31.75x1.5 mm (Section No. 20831), bottom size 92x31.75x1.5 mm (Section No. 20832) and shutter top and bottom size 40x18x1.55 mm (Section No. 20736) and sides (handle) of size 40x18x1.55 mm (Section No. 20738) and lock side shutter frame of size 40x18x1.55 mm (Section No. 20737) including rubber gasket, beading and locking arrangement including making good the disturbed portion complete including stainless steel wire staples and including fixing 5 mm thick glass with necessary rubber beading gasket etc including necessary plaster, painting, cill and making good to disturbed portion complete all as specified and directed. ( Note : Glazing is deemed to be included in the quoted rate of contractor and will not be paid for separately. )

M&L for anodized aluminium powder coated(minimum thickness of powder coating 50 micron) ventilator louvers type, frame top and bottom of size 31x42x1.6 mm (Section No. 20558), rectangular tube of size 40x20x2 mm (Section No. 14019) and middle vertical of size 42x46.20x1.6 mm ( Section No. 20560) and clip for fixing in wiremesh and glass of size 19x17.30x0.90 mm (Section No. 19360) including rubber gasket, beading and locking arrangement including making good the disturbed portion complete including stainless steel wire staples and including fixing 5 mm thick glass with necessary rubber beading gasket etc including necessary plaster, painting, cill and making good to disturbed portion complete all as specified and directed. ( Note : Glazing is deemed to be included in the quoted rate of contractor and will not be paid for separately. )

M&L for Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleats for fixing etc.(minimum thickness of powder coating 50 micron) complete all as specified and directed.

S&F in repair for looking mirror of size 1.50m X 1.00 m with designer glass (5mm thick ) and frame to be fitted with wall including all necessary arrangements (fixed with SS studs ) and fittings complete all as specified and directed.

M&L for 5 mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed.

M&L for Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

S&F/ in repair brass barrel tower bolts of extruded section 300mm long complete,

S&F in repair Brass sliding door bolt with brass hasp, staples (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or Brass of bolt 250mm complete all as specified and directed.

S&F in repair brass handles cast type anodised of 150mm complete all as specified and directed.

S &F Plain, galvanised, mild steel coloured 2 mm thick GI sheet for eaves gutters / valley gutter in design pattern welded to steel frame including made to shape ,all as specified and directed.

Supply & Fixed in repairs Towel Rail 600 mm long stainless steel complete all as specified and as directed.

M&L for ENDURA outdoor full body Vitrified tiles 30 cm x 30 cm x 10 mm thick, jointed and pointed in neat cement slurry and pointed in white on coloured cement to match as in floors etc laid over in patches and including 15 mm thick screed bed or bedding layer of cement mortar 1:6, complete all as specified and as directed.

M & L for Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or n exc 10 Sq m on plan and getting out in soft / loose soil complete all as specified and directed.

M&L for RCC M-25 (20 MM graded stone aggregate) as in walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses etc all as specified

M&L for RCC (design mix) M-25 using 20 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed .

M & L for form work for faces of walls, retaining walls etc. for rough finished surface, complete all as specified and directed .

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, complete all as specified and directed .

M&L for TMT bars 10 mm over dia including cutting bending binding cranking placing & binding with MS wire (annealed) not less than 0.90mm dia as in main/distribution reinforcement complete all as specified and directed.

M&L for TMT bars 8 mm dia including all cutting bending binding cranking placing & binding with MS wire (annealed) not less than 0.90mm dia as in main/distribution reinforcement complete all as specified and directed.

S&F in repair of Reinforced concrete pipes 600 mm bore class NP-3 Laid and jointed complete with collars all specified.

Preparation of plastered or unplastered new surface of wall and applying two coats of cement base paint complete all as specified.

Removal of surpluse excavated material n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

EXTRA for forming fair finish to drain or channel 30 cm inner girt in cement concrete using extra cement incluiding formings moulds mitred stopped ends etc complete.

M&L for rendering on fair faces of brick work or concrete surface of wall 10 mm thick in CM 1:4 and to be finished even and smooth without using extra cement etc complete all as specified and directed

Repairs to pot holes any depth, not exc 1 Sqm each including sweeping free from dust and mud or water, scoring sunken surface in roads, paths etc cutting around edges to least 25 mm in depth, making good by filling in screened & graded road metal, watering and well ramming (including supply of road metal) complete all as specified and directed.

Repairs to pot holes any depth, not exc 1 Sqm each including sweeping free from dust and mud or water, scoring sunken surface in roads, paths etc least 25 mm in depth, making good by applying tack coat at 5 Kg per ten sqm, putting in premixed bituminous macadam, well rammed and shield with binder 9.8 kg per 10 Sqm, blinded with 0.09 cum of stone chipping, 6.3mm size and again well rammed (including supply of premixed macadam, binder and chipping) depth of pot holes exec 30mm complete all as specified and directed.

Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area exc 400Sqm and depth n exc 50mm by using mechanical scarifier including racking over and grading the broken-up surfaces to the proper camber or removing to a distance not exc 50M from the starting point and stacking complete all as directed.

Preparing unsurfaced water bound macadam surfaces by brushing with wire brushes for re-moving caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. and applying evenly a priming/ tack coat with bituminous primer of bitumen of grade VG-10 @ 10 kg per 10 sq metres using mechanical sprayer complete all as specified and as directed.

Preparing black top surfaces by brushing with wire brushes for re-moving caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. and applying evenly a priming/ tack coat with bituminous primer of bitumen of grade VG-10 @ 5 kg per 10 sq metres using mechanical sprayer complete all as specified and as directed.

M&L for premixed bituminous macadam for consolidated thickness upto 75 mm or less with using 19 mm graded (Grading 2) stone aggregate with minimum 4.0% binder content using paving bitumen VG-30 by weight of total mix, rolled and compacted to required camber and gradient using 8 to 12 tonne tandem vibratory roller complete all as specified and directed. Notes:- (i) Premixed bituminous macadam shall be prepared in hot mix plant only. (ii) Premixed bituminous macadam shall be laid with sensor paver only. (iii) Binder content shall be tested at site as directed by GE.

M&L for bituminous premixed asphaltic semi dense concrete 30 mm consolidated thickness with minimum 5.50 % binder content using paving bitumen VG-30 by weight of total mix, rolled and compacted to required camber and gradient using 8 to 12 tonne tandem vibratory roller complete all as specified and directed. Notes:- (i) Bituminous premixed asphaltic semi dense concrete shall be prepared in hot mix plant only. (ii) Bituminous premixed asphaltic semi dense concrete shall be laid with sensor paver only. (iii) Binder content shall be tested at site as directed by GE.

Preparation of road surfaces and applying thermoplastic reflective paint in marking of minimum 2mm thick single coat as in center line and edge line road marking of 150/100mm width using 'HOT MARK' thermoplastic modern propelled road marking machine as directed including all ingredients such as blinder, glass beads Titanium dioxiide calcium carbonate inter fillers thermoplastic requirment for glass beads shall be the table No 800.4 of MORTH specification including spraying of glass beads etc all as per manufacture instructions and as directed.

Supply and fix in repairs, Supply and fixing cat eye solar reflective type of metal body alloy of size 100 mm x 100 mm x 20 mm with PAMA striplens reflector fixed with and incl MS stud of suitable size as per manufactures instructionsand to be fixed with Epoxy- Resin based adhesive or Special Hot Melt Bitumen adhesive avoiding nails etc complete all as specified and directed.

Supply and fix in repairs Supply and fix solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instructions etc. all as specified and directed complete all as specified and directed.

Supply & Fix in repair 100% water proof metal tubular solar delineator (as per IRC 79-1981) made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed

M&L for moorum/ red bajri, spread in layers n exc 15cm, rolled and consolidated to gradient and camber as required complete all specified and directed. Note:- (i) Compacted thickness shall be measured and paid. (ii) Rolling/ compaction shall be done by vibromax roller only.

S&F, in repair, road sign boards (1200 mm x 900 mm) frame made of stainless steel (Gde SS-304) pipe, 50 mm dia and 3 mm thickness of aluminium sheet including writing of letters and logo in retro reflective tape of appropriate size and PCC block of size ( 300X300X450 mm) , 1:2:4 type B-1 using 20mm graded crushed stone aggregate, as in foundation for embedding of boards complete ( height of sign board above GL should be 2.8 m and 450 mm below GL and width 1.2 mtr) including taking down of old wooden/MS board of any description complete all as specified and directed.

Schedule of credit amount of Rs 1,96,179.00 to be deducted during AOC

J.P ENTERPRISES (BID ID -3357254)