Renovation to open to sky area to office space

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge In cement mortar

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering- All work up to plinth level 1:2:4 (1 cement: 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20mm nominal size derived from natural sources) for wall base and on top of wall

Providing and constructing concrete block masonry using 150x200x400 mm solid core compact concrete block (Grade C – 50Kg/Cm2) in CM 1:6 including all scaffolding, curing etc. complete For walls

Centering and shuttering including strutting, propping etc. and removal of form for For Chajja

Centering and shuttering including strutting, propping etc. and removal of form for For lintel

Reinforced cement concrete work in lintel beams, chajja above plinthlevel up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarsesand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) For lintel and chajja

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level and above plinth level, Thermo- Mechanically Treated bars of grade Fe-500D or more, lintel, chajja

Hacking the existing plastering as desired at site

Banking excavated earth in layers not exceeding 20cm in depth, breakingclods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m all kinds of soil

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600 x 600 mm

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, etc. complete. For window grill, roof pulins

Providing Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 12 mm cement plaster

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (Asian Tractor / Jonson Nicholson / Berger)

Applying one coat of water thinnable cement primer of (Asian Tractor Premium / Jenson Nicholson) on wall surface Water thinnable cement primer

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ letre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats (Asian Tractor / Jonson Nicholson / Berger)

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) (Asian Tractor / Jonson Nicholson/ Berger)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. (Asian Tractor / Jonson Nicholson/ Berger)

Providing and fixing aluminum work for, windows with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. Brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) Powder coated aluminum (minimum thickness of powder coating 50 micron)

For shutters of doors, windows including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminum (minimum thickness of powder coating 50 micron) required (Fittings shall be paid for separately) Powder coated aluminum (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminum door, window, shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminum snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) plain glass

Supplying and fixing with close nit SS mesh as per approved sample for aluminum shutters

Supplying fixing standard star lock for sliding window shutters as per approved sample

Providing and fixing ISI marked flush door shutters conforming to IS ; 2202 (Part I) non-decorative type, core of block board construction with frame of 1st Class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws, as per approved sample for main doors and balcony doors

Supplying and fixing Stainless steel handles (as per approved sample) for doors as per approved sample fixing with necessary SS Screws

Supplying and Stainless- steel fixing tower bolt 150 mm length as per approved sample

Supplying and fixing Stainless steel all drop as per approved sample

Providing and fixing in position 60mm thick factory made sandwiched puf panels between wo Engineered sheets of precoated profiles sheet of 0.45mm (+0.50%) with plain on one side and corrugated on the other side both the sides total coated thickness with zinc coating 120 grams per sqm as per IS:277, in 240mpa steel grade 57 microns epoxy primer on both side of the sheet and polymer to coat 15-18 microns, sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation. The sand witch panel core shall consist of 50mm thick puf of density not less than 40 kg/ per cum (+/-2). Fixing operations of wall panels shall be completed in all respect as per drawings and specifications and under the overall direction of the Engineer incharge

G.Rajanna