PROVISION OF PARKING SHED AT DSC COY PCC ROAD PERIPHERY TO BUILDING No 1012 ANTI STATIC FLOORING IN T3S D DIVISION WATER COOLERS POWER SOCKETS TO STORE ROOM OF PSSL BUILDING AND SECURITY LIGHTS TO APPROACH ROAD AT VARIOUS LOCATIONS IN TECHNICAL AREA

Amount

M&L, Point wiring for One socket outlet, 3 pin, 5/6Amps, on independent board controlled by one way switch. complete with FRLSH PVC insulated unsheathed cable 1100V grade conforming to IS-694, 1.5 Sqmm (nominal area) multistranded with copper conductor drawn through and including non metallic rigid PVC conduit, medium grade, of minimum 20mm dia (ISI marked) and conduit accessories fixed to surface of walls/floors/ceilings/roofs etc., with PVC sleeve/dash fastener and cadmium plated screws with sunken type pressed steel/welded mild steel terminal boxes made out of 1.6mm mild steel sheet concealed in walls, 3mm thick phenolic laminated sheet cover for mounting of switches, socket outlets, regulators etc., complete including provision of FRLSH PVC insulated unsheathed 1.5Sqmm solid copper conductor as earth continuity conductor and connecting to common earth dolly complete all as specified and directed.

S&F, Switch socket combination multipurpose 2 in 1, 3 Pin, 5Amps, flush type, universal, ISI marked complete all as specified and directed.

Fixing only water cooler stainless steel, electric driven, single phase, storage type of any capacity including connecting up water inlet line and drain out with necessary fittings complete all as directed. Note: Quoted rate shall deemed to include the cost of transportation of water cooler from Store yard of AGE E/M to location

Fixing only slim type wall mounting voltage stabilizer for of any capacity complete all as directed. Note: Quoted rate shall deemed to include the cost of transportation of stabilizer from Store yard of AGE E/M to location

Supplying and laying of CPVC pipes of outer diameter 20mm, SDR 11 and Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m depth for foundation, for laying of pipes/cables/poles etc., and getting out in any type of soil complete all as specified and directed.

All as per item No 6 but depth exceeding 1.50m and not exceeding 3.0m

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick each layer as in soil complete all as specified and as directed.

Removing excavated material/soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Supply and spreading natural river sand of approved quality for cushioning of cable laid in trenches including compacting and leveling complete all as specified and as directed Note: Punned thickness will only be measured and paid.

Supply and laying un reinforced precast concrete cable cover, class LV Type 1, size 250mm x 150mm x 40mm, laid flat adjacent to each other, perpendicular to cable in trenches for protection of cable complete all as directed.

M&L, PCC 1:3:6, type C-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete etc., for pole concreting complete all as specified and directed.

M&L, PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in coping to poles including necessary formwork complete all as specified and directed.

Supply and erect steel tubular swaged poles type 410 SP-31 (9 metre long) complete with cast iron base plate, finial taper plug, bolts, nuts, screws as specified in true vertical position complete including 2 coats of aluminium paint over a coat of primer on all exposed surfaces and tarring with black bituminous paint to embedded portion in PCC and providing 3 No of 15cm wide radium circular bands in red & yellow on painted portion of pole starting from 1.5m above coping at a gap of 5cm in between 2 bands, writing of pole number in yellow paint over black painted back ground at a height of 2m from GL with 5cm long 2" wide bold letters complete all as specified and directed.

Supplying, laying, jointing, testing and commissioning 1100 volts grade, LT XLPE insulated, PVC sheathed as per IS-7098 (Part-I), 1988 with latest amendments, galvanized steel strip or wire armoured, heavy duty, electric cables, with multistranded aluminium conductor laid in trenches/ passing through pipe/duct/road crossing or fixed on poles, walls with suitable size clamps made out of mild steel flat iron including jointing material such as crimping type lugs, brass cable glands, heavy duty double compression type etc., including disconnecting and taking down unserviceable cable complete all as specified and directed for the following sizes:- Note: Earthwork Excavation, sand cushioning, GI pipe and cable protection will be measured and paid separately.

3.5core 120Sqmm

3.5core 25Sqmm

Cutting of existing bituminous/PCC road or flooring/plinth protection, for laying of GI pipe in road intersection for passing of LT XLPE cable including excavation in any type of soil, returning and filling in and making good top 30cm of the trench by providing PCC 1:2:4 type B1 using 20mm graded stone aggregate to flush with existing road surface complete all as directed.

S&F, 50mm dia GI pipe light grade fixed to walls/poles or laid in trenches, road crossing etc., for protection of underground cable/earth strip including sealing ends with hessian cloth impregnated with bituminous compound in ground and with teak wood bushes for ends fixed on walls/poles complete all as specified and directed.

S&F, hot pressed moulded SMC junction box of internal size 250 x 200 x 100mm, IP 55 with integrated membranes / metric knockouts for cable entry with terminals and arrangement for incoming and outgoing 3 phase 4 wire system with R,Y,B & N studs and control for incoming and outgoing cables, including MCB SP 10Amp, 'D' clamps made of flat iron 25 x 3mm, suitable to pole of any size including bolts nuts and washers etc., complete all as specified and directed.

Make: Sintex CAT No GSJB 2520 or equivalent in Hensel as approved by GE

Note: The unit rate quoted shall be deemed to include for incoming & outgoing cables glands & lugs of size upto 25Sqmm 3.5 core.

S&F, 60W high efficient LED Street light fixture, single piece aluminum pressure die cast housing (LM6 alloy), System lumens not less than 6600lm, Luminaire system efficacy ≥110 lm/W, high purity polycarbonate/glass diffuser, with silicon gaskets for IP66 (No glue) protection, IK07, surge protection in 10KV, IEC 60598 to be followed, driver efficiency >85%, power factor > 0.95, THD ≤10%, LED Makes: Nichia/ Cree/ Osram/ Philips Lumiled, colour rendering index CRI >70, temp range 0 to 45 degree centigrade, CCT: 5700K, lifetime of LED 50000hours @ L70 B50 (As per TM21), photo biological safety report as per IEC 62471, voltage range 120-270V AC and safety on low voltage/high voltage, BIS R No. is mandatory and name of the company or logo must be embossed for LED light fixtures/drivers, submission of LM79, LM80 certification & TTR before claiming payment complete all as specified and directed. Make: Havells Model No ENDURAPEARLNEOSL60WLED 757PASYTOPC or Philips Model No BRP062 LED65 CW SLA S1 PSU or Techno commercially equivalent in Wipro.

S&F, bracket suitable for street light fitting made out of 40mm dia GI tube light grade 1.5m long bent to shape, fixed with necessary nuts bolts and a pair of clamps made of 32x6mm flat iron complete all as specified and directed.

Supply and laying or fixing or passing through pipe, 3 core 4Sqmm nominal cross section, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed in service connections complete all as specified and directed.

S&F, CRCA sheet metal enclosure with metal clad plug and socket three phase with a five pin and earth plug & socket suitable for surface/flush mounting, 415V, 63Amp capacity controlled by and including one No 63Amp MCB TPN 10KA complete all as specified and directed. Make: Legrand/Siemens / L&T / IndoAsian / C&S / Schneider as approved by GE

S&F, factory made sheet metal enclosure distribution board (MCCB DB) TPN 4Way, with 250Amps rated copper bus bar, neutral links and earth bar, double door vertical type, powder coated, suitable for use on 415V, 50Hz supply, MCCB as incomer and MCBs as outgoing IP 43 IK 09 protection complete all as specified and directed. Make: Legrand/Siemens / L&T / IndoAsian / C&S / Schneider as approved by GE

S&F, 3pole 200Amp MCCB with adjustable thermal and magnetic settings, 50Hz, 36KA rupturing capacity at 415volt, conform to IEC -60947-II/ IS-13947-II complete all as specified. Make: Legrand CAT No 4202 38 or equivalent in Siemens / L&T /C&S /Schneider/IndoAsian(Optipro)

S&F, MCB TP, 63Amps, 415volts, 10KA, ISI marked complete all as specified and directed. Make: Legrand Cat No 4086 61 or equivalent in Siemens /C&S /Schneider / IndoAsian(Optipro) as approved by GE

Surface dressing in any type of soil not exceeding 15cm deep complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed.

M&L, 100mm thick PCC 1:4:8 type D-2 in sub base using 40mm graded stone aggregate finishing the surface even and rough including necessary formwork complete all as specified and directed.

M&L, 100mm thick PCC 1:3:6 type C-2 in sub base using 40mm graded stone aggregate including necessary formwork complete all as specified and directed.

M&L, 200mm thick PCC 1:2:4 type B-1 in flooring/path using 20mm graded stone aggregate finishing the surface even and smooth including necessary formwork complete all as specified and directed.

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade ‘A’, complete all as specified and directed.

Removing excavated material/soil to a distance exceeding 250m but not exceeding 500m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

M&L, PCC 1:4:8, type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete etc., concreting complete all as specified and directed.

M&L, PCC 1:2:4, type B-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete etc., concreting complete all as specified and directed.

M&L, brickwork with sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L, PCC 1:2:4, type B-0 using 12.5mm graded stone aggregate as in roof curbs, coping and platform to water tanks and the like including necessary formwork, weathering, slightly rounded or chamfered angles and throating and other similar works complete all as specified and directed.

M&L, 15mm thick rendering in cement mortar 1:4, on fair faces of brick or concrete surfaces, in any height, finished even and smooth without using extra cement complete all as specified and directed.

M&L, hardcore broken stone of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L, 50mm thick sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L, 60mm thick, M-35 Grade, machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658-2006 complete all as specified and directed

S&F, Roof trusses (framed), trussed, purlins, crane gantries rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe 410W (Grade E-250) quality 'A' complete all as specified and directed.

S&F, Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet / trapezoidal steel sheet 0.50mm base metal thickness of any colour having tensile strength of 550MPa as in roof covering/cladding to wall, fixed with self tapping screws and EPDM washers complete all as specified and directed.

S&F, Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550MPa as in ridges, hips, valley gutters, drip and straight flashings, fixed with self tapping screws and EPDM washers complete all as specified and directed.

M&L, preparation of new steel surfaces of any description, over 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L, preparation of newly plastered surfaces of walls including cornices, pilasters, soffits of slabs and chajjas and applying two coats of cement base paint over a coat of primer complete all as specified and as directed.

Demolition of PCC in ground floors and pavings not exceeding 15cm thickness (below or above ground level) complete including disposal of debris off the premises all as directed by Engineer in Charge.

M&L, 50mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in flooring, finishing the surface even and smooth using extra cement including necessary formwork complete all as specified and directed.

M&L, Nitoflor SL Conductive flooring topping in two coats (under coat + top coat) under coat embedded with self adhesive copper tape over 3mm thick high strength self smoothing epoxy screed Nitoflor EU5 over a coat of primer using Nitoprime 25 including preparation and cleaning of surfaces by mechanical means to remove oil, grease to ensure surfaces are dry and free from all traces of containments including use of blasting techniques, grinding of floor surface to remove surface undulations to sound, clean concrete, taking down damaged conductive flooring with screed and disposing of rubbish material off the premises complete all as specified and directed. Flooring treatment shall consist of the following: Note: The treatment shall be got executed through authorized applicator of the make under their supervision and guidance.

Preparation and cleaning of surfaces by scarifying, blasting and grinding as per manufacturer's instructions.

Applying one coat of epoxy primer using Nitoprime 25 of M/s FOSROC or techno commercially equivalent in BASF or PIDILITE

Applying 3mm thick high strength self smoothing epoxy screed using Nitoflor EU5 of M/s FOSROC or techno commercially equivalent in BASF or PIDILITE

Fixing self adhesive copper tape of 50micron thick and 25mm wide in bays, bay area not exceeding 2.25Sqm each. The self adhesive copper tape shall be struck at the peripheries of the floor and jointed to the ground. All concrete slabs shall be electrically connected across the expansion and contraction joints by fixing copper tape.

Mixing all components and applying under coat with a trowel or flat using Nitoflor SL Conductive of M/s FOSROC or techno commercially equivalent of product in BASF or PIDILITE

Mixing all components and applying 2mm thick top coat with a trowel or flat using Nitoflor SL Conductive of M/s FOSROC or techno commercial equivalent product in BASF or PIDILITE

S&F, Earth continuity conductor with 20 x 3mm copper strip fixed to wall on batten or recess or chases with necessary porcelain insulators or buried in ground or drawn in conduit/pipe/wall or fixed to poles or any other indicated situation for loop earthing etc., complete all as specified and as directed.

S&F, epoxy spacer insulator with one GI stud bolt with nut and washer with necessary drilling for bolt hole for holding or fixing roof / down conductor of lightning complete all as specified and directed

M&L, Earthing complete with copper earth plate electrode of size 600 x 600 x 3mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of plate not less than 1.5m below normal ground level connected to copper strip 20 x 3mm as earth lead by means of bolts, nuts, washers and check nuts made out of galvanized iron or steel all as shown on Electrical Plate No. 3 of SSR Part-I including testing on completion complete all as specified and directed.

Notes: The unit rate shall also include for earth work in any type of soil, PCC 1:3:6 type C1 chamber, 50mm thick RCC 1:2:4 type B-1 using 20mm graded stone aggregate cover slab reinforced with 6 Nos of 8mm dia TMT bars both ways, funnel with watering pipe 20mm dia medium grade, GI protection pipe medium grade 25mm dia and wire mesh complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub-heading earthing, specified on Sl Page No. 446 of SSR Part-II.

Copper earth strip beyond 7.5m will be measured and paid separately.

SHAH ENTERPRISES

M/S PAVANI ENTERPRISES