Repairs to sunken floors roofs joinery sanitary fittings plastering internal water supply and certain other misc works at BT Regt in the area of AGE B/R-II under GE (N) Ahmednagar

Amount

Dismantling timber scantlings 40 sq. cm and over in section, in any position etc complete all as specified and directed by Engineer-in-Charge

Demolition of cement concrete (un-reinforced) in ground floor & paving n.exc. 15cm thick below or above ground level etc complete all as specified and directed by Engineer-in-Charge

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed by Engineer-in-Charge

M & L for 6mm thick asbestos cement, corrugated or semi corrugated sheets in roof walls fixed with 'L' type or 'J' type or cranked hook bolts, washer including dismantling etc complete all as specified and directed by Engineer-in-Charge

Fixing only 6mm thick asbestos cement, corrugated or semi corrugated sheets in roof walls fixed with 'L' type or 'J' type or cranked hook bolts, washer etc including dismantling etc complete all as specified and directed by Engineer-in-Charge

M&L for Roof tiles, Mangalore pattern, interlocking at side joints, laid dry including dismantling etc complete all as specified and directed by Engineer-in-Charge

All as per Sl item No 6 (here-in-before) but except tiles (Using old tiles)

M&L for ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge

M&L for 2nd class hard wood for clean swan battens at 25 cm centre to centre of size exc 5 & n exc 15 sqcm etc including dismantling etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs for false ceiling with Vinyl faced Arm-Gyp-FB, ceiling 600 x 600 x 9mm thick with washable metalized polyester foil backing with Vinyl covered edges, supporting sections shall be of suitable size from same makes embossed on sections and level adjuster duly suspended by 2 mm dia GI wire fixed to roof at 600mm centre to centre as per manufacturer's instructions / specification and directed including taking down/ out existing etc complete all as specified and directed by Engineer-in-Charge

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick with mangalore tile profile, of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws including dismantling corrugated steel sheeting, any gauge, thickness etc complete all as specified and directed by Engineer-in-Charge

M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof fixed with self tapping screws complete all as specified, colour and design as approved by GE including dismantling of plain steel sheeting, any gauge, thickness etc complete all as specified and directed by Engineer-in-Charge

S&F of Steel work in tubular trusses including special shaped washer etc. complete conforming to I. S.1161-1979 grade St.-240 etc complete all as specified and directed by Engineer-in-Charge

S&F of steel work in post, Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. as per Fe 410 -W (Gde- E- 250) quality- A etc complete all as specified and directed by Engineer-in-Charge

M&L for preparation surface of tiles or slate battens, any size and spacing and treated all over measured overall on one side only(spaces not deducted) and applying creosote oil etc complete all as specified and directed by Engineer-in-Charge

Material and labour for providing water proofing treatment on roofs, as per manufacturer's instructions and as specified after taking down/out as existing tar felt at site etc complete all as specified and directed by Engineer-in-Charge:- (a) Cleaning the newly plastered surfaces with wire brushes and applying a coat of bituminous primer @ 0.30 ltrs/sqm and allow to dry. (b) Applying and laying torch APP polymer modified bituminous membrane 3 mm thick with non woven polyester mat as reinforced weighing not less than 3 kg/sqm by thermo fusion process as per manufacturers specification including applying one coat of aluminum paint.

M&L for rendering 10 mm thick in CM 1:3 by using 100% coarse sand on roof mixed with & including WPC @ 3% by weight of cement and finished the surfaces even and smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge

M&L for rendering, 10 mm thick on brick / concrete surfaces in cement and sand mortar (1:6) surfaces finished even and smooth without using extra cement including taking down cement mortar plaster on brick or stone walls, raking out joints, hacking for key etc complete all as specified and directed by Engineer-in-Charge

M & L for preparation of newly plastered surface of wall and applying two coats of OBD etc complete all as specified and directed by Engineer-in-Charge

M & L for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide etc complete all as specified and directed by Engineer-in-Charge

M & L for pre-cast cement concrete solid blocks, exc. 10 cm in width type C-1 (1:3:6) using 20 mm graded stone aggregates and setting in cement and sand mortar (1:6) including demolition etc complete all as specified and directed by Engineer-in-Charge

All as per Sl item No 21 (here-in-before) but using old concrete solid blocks setting in cement and sand mortar (1:6) including demolition etc complete all as specified and directed by Engineer-in-Charge

M&L for rendering, 15 mm thick on stone/brick / concrete surfaces in cement and sand mortar (1:4) finished even and fair without using extra cement etc complete all as specified and directed by Engineer-in-Charge

M & L for moorum filling in floors or paving laid in layers n.exc. 15 cm thick spread leveled and rammed including watering etc complete all as specified and directed by Engineer-in-Charge

M&L for hard core of gauge etc. 63 mm but n. exc. 100 mm deposited spread and leveled in layers n. exc. 15cm thick water and rammed etc. Complete all as specified and directed.

M/L for providing 75mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base etc complete all as specified and directed by Engineer-in-Charge

Material and labour for 60 mm thick, PCC pavers interlocking tiles of glossy finish, with grey cement and pigment ,any shape & size conforming to IS 15658 of 2006. M-35 grade made up with 12.5mm graded mechanically crushed stone aggregates, factory made over and incl 30mm thick sand cushioning and joints filled with fine sand incl leveled with plate vibrator & sweeping etc complete all as specified and directed by Engineer-in-Charge

M&L for coloured glazed ceramic tiles 300x450mm , 7-8 mm thick as approved by GE as in dado / skirting or on vertical surfaces laid, over and including 10 mm thick backing coat in cement and sand mortar (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed by Engineer-in-Charge

M&L for joint free anti skid ceramic coloured tiles 8-10 mm thick of size 600x600 mm, as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6 ) set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile etc complete all as specified and directed by Engineer-in-Charge

Material and labour for joint free anti skid ceramic coloured tiles 7-8mm thick matching to dado tiles of size 300x300mm, as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6) set and jointed with neat cement slurry and pointed with white or coloured cement to match the shade of tiles etc complete all as specified and directed by Engineer-in-Charge

M&L in repairs for machine cut kota stone slab flooring 20-25mm thick laid over and including 20 mm thick screed base in cement and sand mortar (1:6) mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge

M&L in repairs for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over & including 15 mm thick backing coat in cement and sand mortar (1:4) etc complete all as specified and directed by Engineer-in-Charge

M&L in repairs for 16mm to 18mm thick pre-polished granite stone slab of approved shade and colour Jet Black / Telephone Black as in top table, top of WHB, kitchen slab/platform, steps, gate pillars, cills etc or on vertical surfaces including vertical projection, full round molding the edge with and including 10 mm thick backing coat in cement and sand mortar (1:3) jointing & pointing in white cement (1:2 ) using marble dust with admixture of pigment to match the shade of granite rubbing including dismantling etc complete all as specified and directed by Engineer-in-Charge

M&L for dholpur stone cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.5 sqm area fixed with and including one number SS clamps (grade -202) of flat-30mm X2mm, 150mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing & including silicon treatment at height more than 6 mtr etc complete all as specified and directed by Engineer-in-Charge

M & L for preparation of new plastered surfaces of wall and applying two coats for cement based paint etc complete all as specified and directed by Engineer-in-Charge

M & L for preparation of old wooden surface and applying one coat of synthetic enamel paint etc complete all as specified and directed by Engineer-in-Charge

M & L for preparation of old steel surface and applying one coat of synthetic enamel paint etc complete all as specified and directed by Engineer-in-Charge

M & L for preparation of old plastered surface of wall and applying one coat of cement paint etc complete all as specified and directed by Engineer-in-Charge

M & L for preparing old plastered surfaces of walls and apply one coat of OBD, finished with roller finish on plastered surfaces of wall etc complete all as specified and directed by Engineer-in-Charge

M&L for complete removal of old distempered and painted surfaces of walls and applying two coats of Luster (any tint) over a coat of suitable primer etc complete all as specified and directed by Engineer-in-Charge

M&L for preparation of old plastered treated surfaces of walls by brooming down and and applying one coat of weather proof 100 % acrylic exterior emulsion apex ultima paint of any tint as approved by GE after cleaning the surfaces etc complete all as specified and directed by Engineer-in-Charge. Make : Asian paints or equivalent makes mentioned in list of makes in Appendix `C'

M&L for 2 mm thick wall care putty etc complete all as specified and directed by Engineer-in-Charge

S&F fix in repairs wash hand basin vitreous China white , flat back or angle type of size 500 X 400 mm incl pillar tap 15mm dia CP, waste chain and plug and porcelain stopper , waste pipe, a pair of brackets, or erecting stand and PVC connection etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistern etc complete all as specified and directed by Engineer-in-Charge. make as per list of makes mentioned in appendix `C

S&F in repairs 10 ltr capacity PVC valve less, symphonic action type, flushing cistern, low level, all accessories etc complete all as specified and directed by Engineer-in-Charge. make as per list of makes mentioned in appendix `C

S&F in repairs, shower rose with shower arm make mentioned in list of makes in appendix `C' etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs vitreous china wash down water closet (Pedestal pattern) white including fixing bolts with and including plastic water closet seat cover closed pattern with flat bottom and cover and MSCP almn hinges device etc complete all as specified and directed by Engineer-in-Charge connecting to 'P' or 'S' trap etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs looking mirror of size 800 mm X600 mm, etc complete all as specified and directed by Engineer-in-Charge

Taking up or down 15 mm bore steel tubing and connections.

All as per item No 49 (here-in-before) but 20 mm bore tubing

All as per item No 49 (here-in-before) but 25 mm bore tubing

Supplying and laying 16 mm dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings etc complete all as specified and directed by Engineer-in-Charge

All as per item No 52 (here-in-before) but 20 mm bore tubing etc complete all as specified and directed by Engineer-in-Charge

All as per item No 52 (here-in-before) but 25 mm bore tubing

S & F PVC connections 15 mm size with PTMT nuts of length 450 mm etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs stop cock cast copper alloy, Chromium plated fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge,

S&F in repair PVC bib tap 15 mm dia, screwed for iron pipe etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe etc complete all as specified and directed by Engineer-in-Charge.

S&F rotational molded polyethylene water storage tanks double layered (cylindrical vertical with closed top) of 500 litres capacity, triple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe, tank nipple and connected etc complete all as specified and directed by Engineer-in-Charge

All as per item No 61 (here-in-before) but 1000 ltr capacity

Taking down chowkhats or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge

Taking down chowkhats or frames exc. 1.5 sq. m and n exc 4.00 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge

S&F anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc complete all as specified and directed by Engineer-in-Charge

S&F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed by Engineer-in-Charge

S&F powder coated aluminium anodised aluminium frame, shutters for door,windows, ventilators with one or more rebates including joining cleat for fixing etc, rubber / neoprene beading and locking arrangement etc complete all as specified and directed by Engineer-in-Charge

M&L 12 mm thick prelaminated particle board balancing white lamination on both sides,fixed with screws to frame work etc complete all as specified and directed by Engineer-in-Charge

M & L for 4 mm thick plain sheet glass ordinary quality and glazing with oil putty or wooden beads in squares n.exc 0.50 sqm in each pane etc complete all as specified and directed by Engineer-in-Charge

M & L for 5.5 mm thick tinted sheet glass ordinary quality and glazing with oil putty or wooden beads in squares .exc 0.50 sqm in each pane etc complete all as specified and directed by Engineer-in-Charge

S & F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks ,or galvanised wire staples including necessary beading etc complete all as specified and directed by Engineer-in-Charge

S&F venetian blind have 2 incl slats that open and close with a chain / cord of vinyl or mini blinds etc complete all as specified and directed by Engineer-in-Charge

Supply and fix aluminium die cast body Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover,governing pivot made of brass, other parts made of mild steel heavy duty and fixed etc complete all as specified and directed by Engineer-in-Charge

Taking down aluminium shutter from frame exc 1 sqm but n exc 2 sqm and re-fixing in position after repair etc complete all as specified and directed by Engineer-in-Charge

S&F 35 mm thick IInd C/L H/W glazed & skeleton shutters open rebated and prepared to receive glass gauge, divided into square or rectangles with plain chamfered or rounded mitered & rebated slash bars including beads mitered for securing glass wire gauge etc complete all as specified and directed by Engineer-in-Charge

M&L for 35 mm thick plain framed, paneled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial plywood. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated etc complete all as specified and directed by Engineer-in-Charge

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides etc complete all as specified and directed by Engineer-in-Charge

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded etc complete all as specified and directed by Engineer-in-Charge

S & F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hings, lock strike plate, etc complete all as specified and directed by Engineer-in-Charge

S & F pressed steel door frame of size 100 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed by Engineer-in-Charge

S&F butt hinges medium weight cold rolled mils steel 100mm long etc complete all as specified and directed by Engineer-in-Charge

S&F aluminium anodised barrel tower bolts of extruded section 150mm long etc complete all as specified and directed by Engineer-in-Charge

S&F aluminium anodised handle of extruded section 150mm long etc complete all as specified and directed by Engineer-in-Charge

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 300mm long etc complete all as specified and directed by Engineer-in-Charge

S&F 300 mm mild steel ordinary rat tail rod pattern door spring including roller and roller plate etc complete all as specified and directed by Engineer-in-Charge

M&L for special treatment to sunken slab floor incl WC trap etc including cleaning and preparing the surface area for carrying out membrane water proofing treatment, then injection grouting the weak areas on the concrete surface with cementitious grout and applying 10mm thick cement plaster in cement and sand mortar (1:4). Then providing and laying Mineral Top APP (Atactic Polypropylene Polymer) modified prefabricated 5 layer 3mm thick water proofing membrane, black finished reinforce with non woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 Litre per Sqm by the same membrane manufacturer of density at 25ºC, 0.87-0.89 Kg per litre and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc and preparing the surface complete. and providing PCC 1:5:10 type E2 using 40mm graded mechanically crushed stone aggregates in sunken slab and 75mm thick PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates as base, 40mm bore GI pipe, light grade of length not less that 50 cm as spout, non-skid glazed tiles as per existing pattern/size/tint with and incl WC vitreous china squatting pan 580x440mm with integral footrests/pedestal pan incl seat cover, white, area of WC n exc 1.50 Sqm etc after dismantling the existing sunken floor etc complete all as specified and directed by Engineer-in-Charge Make : Super Thermo lay MT of STP / TEXSA / FosRoc Note : Work has to be carried out strictly by the authenticated applicator of the manufacturer and as per manufacturers specification as approved by GE.

S & F in repair Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed in any position any type of opening with and including wooden beads etc complete all as specified and directed by Engineer-in-Charge

M & L in repairs for 3 mm thick sheet frosted/pin headed glass ordinary quality and glazing with oil putty or wooden beads in squares n.exc 0.50 sqm in each pane etc complete all as specified and directed by Engineer-in-Charge

M & Lin repairs for 4 mm thick plain sheet glass ordinary quality and glazing with oil putty or wooden beads in squares n.exc 0.50 sqm in each pane etc complete all as specified and directed by Engineer-in-Charge

S&F in repair wall mounted cloth drying stand consisting of 16 mm dia powder coated MS rods of CR steel mounted on powder coated MS square pipe, 16- 4 rods, 4ft each, total weight not less than 3.80 Kg, fixed to wall including all fittings/accessories etc complete all as specified and directed by Engineer-in-Charge Make -Easy dry Model: Mount it or equivalent product as approved by GE.

M&L for cleaning of service tank up to 500 ltrs by removing all scales, dirt, silt, mud etc from tank and mouth of outgoing pipe including washing of tank internally with bleaching powder after removing scale, dirt, silt, mud etc from tank and removing algae from outside of tank from below bottom of tank and disinfecting tank by spraying sodium hypo chloride solution in tank and writing date of cleaning on tank with synthetic enamel paint size of alphabet / numerical shall be minimum 7 cm etc complete all as specified and directed by Engineer-in-Charge. Note:- The quoted rate shall include dismantling and refixing of water tank as etc complete all as specified and directed by Engineer-in-Charge

All as per item No 92 (here-in-before) but 501 to 1000 ltrs

An amount of Rs 58,965.00 shall be deducted from BOQ on account of schedule of credit

M/S. M. F. Sharif & Co.

M/s AG PATHAN

M/S MAHESHWARI ENTERPRISES

M/S. Z.K.ENTERPRISES, AHMEDNAGAR

HG PATHAN CONSTRUCTION COMPANY