SPECIAL REPAIR TO BLDG NO.T-27 OF APS SCHOOL ,SPECIAL REPAIR OF BUILDING NO.P-13/2 AT APS AND SPECIAL REPAIR TO BLDG NO P-42 AT ROWIRAH IN JORHAT MILITARY STATION UNDER GE JORHAT.

Amount

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including any pattern roof coverings complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as directed.

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) complete all as directed.

Dismantling timber scantling in unframed work, 40 Sq cm and over in section, in any position, complete all as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed.

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Demolition of reed lathing single or double including batten & plaster or chicken wire lathing complete all as specified & as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) n. exc. 1.5 Sq. M each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sq. M but not exc. 4.0 Sq M each, complete all as directed.

Taking up or down, steel tubing 15 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

Taking up or down, steel tubing 20 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

Excavation in post holes (or similar holes) each not exc. 0.5 Cum and getting out in soft/ loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc. 25 cm, watering, and removing surplus soil to a distance not exceeding 50 m complete all as specified and as directed

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil ,complete all as specified and directed.

Returning filling in soft/loose soil, including, spreading levelling watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 Metres and depositing where directed at a level n. exc. 1.5 M above the starting point complete all asspecified and directed.

Materials and Labour for plain cement concrete (1:4:8) Type D-2 using 40 mm graded aggregate in foundations, filling and mass concrete complete all as specified and directed.

Materials and Labour for reinforced cement concrete M-25 design mix in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete ,complete all as specified and directed.

Materials and Labour for reinforced cement concrete M-25 design mix in columns; pillars; piers; posts; struts etc,complete all as specified and directed.

Materials and Labour for reinforced cement concrete M-25 design mix in chajjas,complete all as specified and directed.

M&L for RCC M-25 in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves , baffle wall and the like slabs etc. complete all as specified & as directed.

M&L for PCC (1:2:4) type B-I with using 20 mm graded aggregate as in benching, kerbs copings, edging of drain , hold fast etc including necessary form work wherever required all complete as specified and as directed.

M & L for RCC type M-25 mix using 20mm graded aggregates as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified & as directed.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings , girders, bressummers, lintels, cantilevers, shelves including supports,overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete, flat, complete all as specified and directed.

Use and waste of form work to chullah hoods, chajjas,troughs and similar items including edges for fair finished surfaces of concrete, flat, complete all as specified and directed.

Use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces of concrete, square, rectangular or polygonal, complete all as specified and directed.

Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sided and soffits of plinth beams and similar works; vertical or to batter for rough finished surfaces of concrete, flat, complete all as specified and directed.

M&L for use and waste of form work to soffits of suspended slabs such as roof slabs, landings floor slabs and similar work not exceeding 200 mm thick (horizontal or sloping) for fair finished surfaces of concrete complete all as specified and directed.

Materials and Labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded aggregates as in plinth protection/floor including finishing surface even and smooth without using extra cement complete all as specified and directed.

M & L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. with and including brushing neat cement slurry with 3.0 kg of cement per sq. metre complete all as specified and directed.

Materials and Labour for 100 mm thick plain cement concrete (1:2:4) type B2 using 40 mm graded aggregates as in floor including finishing surface even and smooth without using extra cement complete all as specified and directed.

S & F for glass dividing strips, 38mm wide and 3mm thick, inserted in position to conform to design complete all as specified and directed.

M&L for cement concrete 40mm thick type B-0, 1:2:4 (12.50 mm graded aggregate) as in flooring, finished even and smooth using extra cement all complete as specified and as directed

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,conforming to IS 15622, Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4),complete all as specified and directed.

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,conforming to IS 15622, Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4),complete all as specified and directed.

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,conforming to IS 15622, Grade B II, on vertical surfaces of wall such as dados, skirting etc., set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.MAKE:- (Johnson/Kajaria or equivalent make )

Materials and Labour for, Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,conforming to IS 15622, Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4),complete all as specified and directed.

Materials and Labour for, Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,conforming to IS 15622, Grade B II, on vertical surfaces of wall such as dados, skirting etc., set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.MAKE:- (Johnson/Kajaria or equivalent make )

Material and Labour for Digital Vitrified Ceramic Tiles, , 10 mm thick (square/rectangular) polished area of each tile not exceeding 0.36 Sq M, on floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed.

Material and Labour for Digital Vitrified Ceramic Tiles,, 10 mm thick (square/rectangular) polished area of each tile not exceeding 0.36 Sq M, on vertical surfaces of wall such as dados, skirting etc., set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.

Materials and Labour for, Digital glazed ceramic coloured tiles, 400 X 400 X 7mm thick, conforming to IS 15622, Grade B III, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.

Material and Labour for chequered ceramic tiles, coloured, 12 mm thick (square/rectangular) area of each tile exceeding 0.09 Sq M but not exceeding 0.16 Sq M, conforming to IS 4457-2007, on floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour,over and including 20 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed. MAKE:- (Johnson ‘Endura’/ Somany ‘Durastone’/ Regency ‘Duro’)

Materials and Labour for brick work with Sub Class ‘B’ bricks straight or curved on plan exceeding 6M mean radius built in cement mortar (1:6), complete all as specified and directed.

M & L for forming jambs, etc., to openings, including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work built in Cement mortar 1:6 or cement lime mortar 1:1:8 complete all as specified and directed.

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and directed.

S & F mild steel screw bolts (machine made), diameter of neck 11 to 15 mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exceeding 5 cm long complete all as specified and as directed.

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed.Make(Tata bluescope/Sexena Marine Tech/Dyna )

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based plain steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed.(Tata bluescope/Sexena Marine Tech /Dyna)

Supply and fix mild steel TMT bars 10 mm dia. and over, cut to length, bend to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed

Supply and fix mild steel TMT bars 6 mm to 8mm dia. , cut to length, bend to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed

S & F hot rolled medium and high tensile structural steel of grade E 250 quality C conforming to IS 2062: 2011 as in rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and as directed.

S & F mild steel screw bolts (machine made), diameter of neck 11 to 15 mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exceeding 5 cm long complete all as specified and as directed.

Supply and Fix, 25 mm dia. mild steel conduit ,wall thickness 1.00 mm, overall PVC coated including suitable fixing brackets and fancy type end caps as in darpary rod for doors/ windows, complete all as specified and directed.

Supply and Fix, pressed steel frames, size 125 x 60mm, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and directed.

Supply and Fix, pressed steel frames, size 105 x 60mm, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and directed.

Supply and Fix, in repair sliding window with powder coating of any colour (Thickness of powder coating not less than 50 micron), 63 mm x 47 mm for sliding windows with one or more rebates including joining cleat for fixing etc., with sliding type shutters,without sash bars, aluminium sections with powder coating of any colour (Thickness of powder coating not less than 50 micron) 39 mm x 18 mm including necessary joining cleats, glazing clips, rubber packing, aluminium with powder coating of any colour (Thickness of powder coating not less than 50 micron) snap beading, screws etc.(Thickness of aluminium sections not less than 1.5 mm),with suitable sliding & locking arrangement, anodised aluminium grill 7.1 mm thick, weighing 2.701 Kg/Sq M,stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and 4 mm thick tinted glass, complete all as specified and directed.

Supply and fix Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, complete all as specified and directed.

Supply and fix Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

Supply and Fix,steel ventilator with top hung shutter including hinges, steel peg stay, complete with glazing bars, dovetailed or welded, including taking down existing unserviceable one including making good disturbed surfaces as per existing specfication complete all as specified and directed.

S & F solid PVC wall lining consisting of 6mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

M & L in repair for 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work with including teak wood lipping 6mm thick complete all as specified and directed.

35 mm thick plain framed, factory made panelled shutter (second class hard wood rails & styles) (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Factory made Glazed and skeleton shutters, 35 mm thick second class hardwood, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

Supply and Fix, factory made rigid lam PVC door frame of size 125 mm x 50 mm, double rebated with wall thickness of extruded 5mm PVC sheet of density 600 kgs/cum , made by joining 3 Nos. heat bent PVC sheet 'C' channel of 5mm PVC foam sheet of size 35mm x 35mm x 25mm & 40mm x 55mm x 40 mm & 25 mm x 35 mm x 35 mm using solvent cement, the two side 'C' channel shall be reinforced with 19mm x 19 mm MS square tube of 19 SWG with all three 'C' ed to flat base of 5mm PVC sheet with solvent cement. The profile shall be mitred cut at two corners and jointed by inserting 4 Nos. 150 mm long brackets of 15mm x15 mm MS square tube inside the 19 mm square tubes. The two vertical members of door frame shall be reinforced with 40mm x 20 mm MS tubes of 19 SWG duly filled with 2nd class hardwood throughout the frame. The door frame shall be fixed to the wall using 100 mm long nikel coated dry wheet screws through the frame by using PVC fastener. Minimum 08 Nos. of screws shall be provided for each vertical member and minimum 04 Nos.for horizontal members etc. as per manufacturers specifications, fixed in opening, complete all as specified and directed.

Supply and fix solid PVC door frame of size 50 mm X 47 mm made out of 5 mm single side prelam PVC sheet with edges painted to match with prelam sheet, reinforced with MS square tube, fixed in opening, complete all as specified and directed.

Materials and Labour 35mm thick for, Factory Made Solid PVC Moulded Door designer Shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC sheet on back face, supplying & fixing in frame at site as per specification and drawing, complete all as specified and directed.

Supply and Fix, factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed.

Supply and Fix,IS markedStainless steel butt hinges, medium weight, cold rolled 100 mm size complete all as specified and directed

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 75 mm long complete all as specified and directed.

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 150 mm long complete all as specified and directed.

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 200 mm long complete all as specified and directed.

Supply and Fix, aluminium handles, cast type, anodized, 150 mm size, complete all as specified and directed.

Supply and Fix, aluminium handles, Fabricated type, anodized, 150 mm size, complete all as specified and directed.

S & F 125mm hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

Supply and Fix,3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed.

S & F for 3.0mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq m in each pane complete all as specified and directed.

Supply and Fix,3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane with and including hacking out old broken glass (any thickness, size, quality or description) from frame including providing wooden beads painted with two coat of enamel paint over a coat of primer complete all as specified and directed.

Supply and Fix, Aluminium Alloy, anodised, sliding door bolt, length of bolt 300 mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Supply and Fix,in repair floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring and with overall length of cover plate 150 mm, fixed in floor, complete all as specified and directed.

S & F in repair 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Materials and Labour for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Grade E-165 complete all as specified and directed.

Supply and Fix, in repair stainless steel wire cloth, 0.36mm nominal dia. of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Supply and Fix, stainless steel wire cloth, 0.36mm nominal dia. of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

M&L providing and fixing of false ceiling with powder coated exposed GI grid suspension system (E-grid T-2420 or equivalent of Armstrong having load carrying capacity of 12.5 Kg/M3 with mid span deflection not exceeding 1/360 span with hanger spacing of 1200 mm c/c) consisting of Main Runner 3600 mm long, Cross Tee 1200/600 mm long and Wall Angle. The wall angle shall be fixed on PVC dash fasteners on the perimeter of the wall with steel screws with distance 300 mm c/c. The main runners to be placed @ 1200 mm, the cross tee 1200 mm will be inserted in the pre-cut slots of Main Runner at regular interval of 600 mm to form a modular grid of 1200x600mm. Additional cross tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600 mm x 600 mm with and including 6 mm thick HSPC (High pressure steam cured) oceanic pre primed, self embossed, textured designer board, water, termite & fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 4 mm dia GI bar hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt 0.007 kg/clip), hold down clips (wt-0.0035 Kg/clip), with provn of light fixture complete all as per manufacturer instructions and as directed. Make Armstrong/Everest

S&F in repairs Gratings chromium plated 140 mm dia fixing in floors with neat cement slurry to match, etc. complete all as directed.

Supply and Fix in repair PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle, of capacity 10 Litres, including brackets, flush pipe, complete all as specified and directed.

Supply and Fix, brass CP fancy wall mixer with L bends for mixing hot & cold water screwed down for iron pipe 15 mm bore and fixed, inlcuding taking out unserviceable existing one complete all as specified and directed. (Make wall mixer cat part no. QQT-7281 of Jaquar or equivalent make Kohler/Marc)

Supply and fix PVC connections 15 mm size with PTMT nuts of length 450 mm,complete all as specified and directed.

Supply and Fix, in repair two way bib tap, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,15 mm bore and fixed, complete all as specified and directed.

Supply and Fix, in repair bib tap, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,15 mm bore and fixed, complete all as specified and directed.

S&F brass chromium plated hand shower (health faucet) complete all as specified and as directed. Make- Jaquar cat No-ALD-BLK-583 or Marc/Kohler)

Supply and Fix, in repair stop valves/Angle cock, cast copper alloy, fancy type, chromium plated,screwed down, high pressure with crutch or butterfly handle, screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.

Supply and Fix,in repair stop valves, cast copper alloy , fancy type, chromium plated, screwed down, high pressure with long shank and cup (concealed type), screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.Make:Cat No.KUB-35053F of Jaquar or equivalent make of Marc/Kohler)

Supply and Fix, Pillar Cock with 200mm Extension Body & Base Flange, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe, 15 mm bore, including taking down existing unserviceable one complete all as specified and directed.Make:Cat No.KUB-35021of Jaquar or equivalent make of Marc/Kohler)

Materials and Labour for galvanized steel tubing, medium grade, 15 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

Materials and Labour for galvanized steel tubing, medium grade, 20 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

S & F 2nd class hardwood small fittings such as brackets of any type, latch and hinge blocks, shapped door and window stops and the like, including all necessary labours; articles n exc 200 cu. cm each

Refixing all serviceable 15mm dia GI tubing and connection with new fittings solid fitting in new or old position on wall/floor complete all as specified and directed

S&F in repair 75mm bore chromium plated shower rose with shower arm of 15mm dia (size of arm 195mm long with bend to 45 degree) complete all as specified and as directed (Make: Jaquar/Marc/Kohler)

S&F 500 ltrs IS marked multilayer rotational moulded polythytene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position with and including 20mm PTMT ball valves high pressure with polythene float and nut with and including dismantling exsiting one complete all as specified and directed .

Supply and Fix vitreous China wash down water closet pan (pedestal pattern), white, (including fixing bolts, flushing cistern and flush pipe connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe etc.including PVC seat cover and taking out of existing one and making good disturbed surfaces as per existing specification complete all as specified and directed.

M & L for cutting openings, through brick walls built in mud mortar for door, window and other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc., to store and rubbish to a distance not exc. 50m complete all as specified and directed.

S & F in repairs wash basins, vitreous china, white, flat back, size 450 mm X 300 mm with and including cast iron brackets (embedded in wall upto 110 mm depth with and including cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate or fixing on wall with and including rawl plug and screws), 32 mm nominal size, copper alloy, nickel chromium plated finish waste fittings, including painting of fittings and brackets, sealing gap between wall and basin with silicone sealant, cutting and making good the walls wherever required and connecting to supply pipes, waste pipes, waste fittings etc. with silicone sealant complete all as specified and as directed.

Materials and Labour for Urinal Valve Auto Closing System with Built-in Control Cock & Wall Flange complete all as specfied and directed Make Cat no.PRS-077 of Jaquar or equivalent of Marc/Kohler

Materials and Labour for Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe), including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and directed.

Materials and Labour for Vitreous China Urinal partition white of size 310mmX700mm complete all as specfied and directed

M & L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in brick walls

S & F of brass chromium plated Bottle Trap (with Internal Partition) 32mm Size with 250mm & 190mm Long W all Connection Pipes & W all Flange with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed Make Cat no.ALD-769L of Jaquar or equivalent of Marc/Kohler

Supply and Fix,75 mm bore UPVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

Supply and Fix, 50 mm bore, low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm fixed complete to walls, ceilings or in floors etc., complete all as specified and directed.

Supply and Fix, in repair PVC (SWR) floor trap, plain with grating including jointing with solvent cement with dia. of out let 75 mm, complete all as specified and directed.

Supply and Fix, in repair soap dish, fixed in wall, complete all as specified and directed.Make Catpart no.AQN-7731 of Jaquar or equivalent make of Kohler/Marc

Supply and Fix, gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe, 20 mm bore, complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel and iron surface not exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel and iron surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Material and Labour for applying one coat of synthetic enamel paint on old painted steel and iron surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

M&L for preparation of old painted surfaces of wood base surface of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel painting complete all as specified and as directed.

M & L for preparation of old painted surfaces of steel base surface of any description, not otherwise described over 10 cm width or girth and applying for two coat of black bituminous paint on surfaces of any description , steel, iron, exceeding 10cm in width or girth complete all as specified and as directed.

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on surface other than fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.

Materials and Labour for rendering 10 mm thick, cement plaster, in cement mortar (1:4) on surface fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on surface fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of new plastered or un -plastered from walls, and applying two coats acrylic distemper on walls, over and including a coat of 2 mm thick white wall care putty complete all as specified and as directed.Make;Berger (Bison)/J&N(Jensolin)/Asain Piants(Tractor)/Nerolac(Beauty)

M&L for preparation of new or previously untreated surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for complete removal of existing treatment from walls, and applying two coats acrylic distemper on walls, over and including a coat of 2 mm thick white wall care putty with and including a coat of primer complete all as specified and as directed.Make;Berger (Bison)/J&N(Jensolin)/Asain Piants(Tractor)/Nerolac(Beauty)

Material and Labour for applying three coats of white wash to new plastered surfaces on walls including preparation of surfaces complete all as specified and directed.

Material and Labour applying two coat of100 % Acrylic Exterior Emulsion paint (Berger,Weather coat Advanced XP Brand/Asain Paints :Apex ultima Brand /ICI:Dulux Weather shield Max Brand/J&N:Safeguard Optima Brand painting over and including a coat of primer to new plastered or unplastered surfaces on walls including preparation of surfaces, complete all as specified and directed.Note (Work shall be exectuted through authorised applicator and shall be got approved by before commencement of work)

M&L for preparing old decorated plastered or unplastered surfaces of celing including cornices, pilasters and other wall features etc by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots etc and applying one coat of white washing on the ceiling all as specified and directed

M&L for preparing old decorated plastered or unplastered surfaces of wall including cornices, pilasters and other wall features etc by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots etc and applying one coat of white washing on the wall all as specified and directed

M&L for preparation of old distempered surfaces of walls including cornices, pilasters and other wall features etc by washing, rubbing down and stopping and applying one coat acrylic distemper on old surfaces complete all as specified and as directed.complete all as specified and directed Make;Berger (Bison)/J&N(Jensolin)/Asain Piants(Tractor)/Nerolac(Beauty)

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Taking down copper/aluminium sub main wiring complete and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L for concealed type wiring using approved colour coding as per IS for one light/ fan/ bell point controlled by one switch with1.5 Sqmm (Nominal area) PVC insulated, unsheathed, multistranded copper, conductor cable FRLSH (1100Volts grade) drawn in and including heavy duty PVC rigid conduits of 20/25 mm dia with all fittings and accessories alongwith PVC insulated multi stranded copper conductor of size 1.5 Sqmm as earth continuity conductor including fixing of 1. 22mm thick MS sunk terminal box duly flushed to wall with 3mm thick plastic laminated/ebonite sheet cover fixed with brass screws,cap and washers complete all as specified and as directed. Note:- (i) The chases in the wall shall be cut with elect cutter (ii) The disturbed surfaces of wall shall be made good with cement plaster 1:4 including matching the surfaces with as per existing finishes and to the entire satisfaction of Engineer in Charge

All as per item No- 134 as above but for one 3/5 pin socket outlet 5 Amps on the same board with other switches.

All as per item No- 134 here-in-before but for switch socket combination 5 Amps 2/3/5 Pin point on independent board.

M&L for concealed type wiring using approved colour coding as per IS for switch socket combination 15 amps 5/6 Pin point on Independent board with 4 Sqmm (Nominal area) PVC insulated, unsheathed, multistranded copper, conductor cable FRLSH (1100Volts grade) drawn in and including heavy duty PVC rigid conduits of 20/25 mm dia with all fittings and accessories alongwith PVC insulated multi stranded copper conductor of size 2.5 Sqmm as earth continuity conductor including fixing of 1. 22mm thick MS sunk terminal box duly flushed to wall with 3mm thick plastic laminated/ebonite sheet cover fixed with brass screws,cap and washers complete all as specified and as directed. Note:- (i) The chases in the wall shall be cut with elect cutter (ii) The disturbed surfaces of wall shall be made good with cement plaster 1:4 including matching the surfaces with as per existing finishes and to the entire satisfaction of Engineer in Charge

M & L wiring for circuit/Sub main wiring concealed type with two single core cable PVC insulated cable with 6.00 Sqmm (Nominal area) multi stranded copper conductor FRLSH cable 1100 volts grade including earth continuity conductor using PVC insulated cable of stranded copper conductor of size 4 Sqmm connected to common earth dolly and drawing into and including steel conduits of size 20/25 mm dia medium grade including making good the disturbed surfaces to match with existing surfaces complete all as specified and as directed. Note:- (i) The chases in the wall shall be cut with elect cutter (ii) The disturbed surfaces of wall shall be made good with cement plaster 1:4 including matching the surfaces with as per existing finishes and to the entire satisfaction of Engineer in Charge

Supply and Fix, switch piano, flush button, single pole, one way, 5 Amps, complete all as specified and directed.

Supply and Fix, switch socket combination 2 in 1, 5 pin, 15 Amp, flush type universal, complete all as specified and directed.

S & F Socket outlet, 2 in 1, 3 pin, 5 Amp complete all as specified and directed.

Supply and Fix, ceiling rose, three terminal, PVC/ Polycarbonate insulated body, complete all as specified and directed.

Supply and Fix stepped type electronic fan regulator, flush type, on existing phenolic laminated sheet etc. as required , complete all as specified and directed.

Supply and laying common burnt clay building bricks, sub-class ‘B’ designation 75, old size bricks, in cable trenches, as cable protection, complete all as specified and directed.

Supply and filling in approved dry sand in cable trenches before and after the cables are laid, as in sand cushioning to cables, complete all as specified and directed.

Supply,laying, jointing and testing of LT, XLPE insulated, PVC sheathed, armoured, heavy duty electric cables with aluminium conductor for working voltage up to and including 1100 volts, of cross sectional area 35 sq. mm, 3 ½ core, including with suitable size of lugs including taking out existing one complete all as specified and directed.

Supply and Fix,decorative wall light fixture made up of polycarbonate, suitable for 10/15 W retrofit LED lamp (Spiral B-22 base), all as per Cat No LHDL02160099 ‘CITY1 NEW’ of Make “Havells” or equivalent Model of Make ‘Bajaj/Philips including LED lamp, 15 Watts, lumen output 1100 lm, colour temp 6500 K, lamp current 0.055 amp, lamp base cap B22,, complete all as specified and directed.

Supply and Fix lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings,complete all as specified and directed.

Supply and Fix, LED lamp, 10 Watts, lumen output 770 lm, colour temp 6500 K, lamp current 0.04 amp, lamp base cap B22, complete all as specified and directed.

S&F Decorative ultra slim linear LED lighting fixture with co extruded polycarbonate body environmental friendly, E-lite LED GREEN 20W, 240 Volt, LED tube light as per Havells Cat No. LUMILINEBS20WLED865SPCWH or equivalent of philips/Bajaj/wipro and including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 Sq mm, 3 core, 1100 Volts grade, from light fitting to point outlet, complete all as specified and directed.

S&F Decorative ultra slim linear LED lighting fixture with co extruded polycarbonate body environmental friendly, 10W, 240 Volt, LED tube light as per Wipro Cat No. LL20-111-XXX-65-NE or equivalent of philips/Bajaj and including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 Sq mm, 3 core, 1100 Volts grade, from light fitting to point outlet, complete all as specified and directed.

Supply and Fix, LED roadway luminaire, 25 Watts, with pressure die-cast aluminium housing,IP-66, high power LEDs as light source and electronic driver, all as per Cat No. LR02-291-XXX-57-XX of Make ‘Wipro’ or Equivalent Model of Make Havells/Bajaj/Philips and including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.75 Sq mm, 3 core, 1100 Volts grade, from light fitting to point outlet, complete all as specified and directed.

Supply and Fix, Heavy Duty Exhaust Fan with self closing metallic louvers, 300 mm sweep, 1400 RPM, Single Phase, 230 V, 50 Hz, all as per Model “Turbo Force” of Make ‘Havells’ or equivalent Model of Make ‘Usha’ / ’Crompton Greaves’/’Almonard’ and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.50 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan complete all as specified and directed.Note: Cost of cutting and making hole for fixing exhaust fan shall be deemed to included in quoated rates

Supply and Fix, double door, sheet metal enclosure for DBs for mounting of MCB for 415 Volts, 4 way, with 200 Amps rated bus bar, Triple Pole & Neutral, with and including taking down unserviceable one complete all as specified and directed. [Cat No.DBTPN004DD of Make L&T or equivalent Model of Make Legrand/Siemens]

Supply and Fix, miniature circuit breaker (MCBs) three pole and neutral, 415 Volts, 10KA, 63 Amps "C" series complete all as specified and directed.

Supply and Fix, miniature circuit breaker (MCBs), single pole and neutral, 240 Volts,10KA, 40 Amps "C" series complete all as specified and directed.

Supply and Fix, double door, sheet metal enclosure for DBs for mounting of MCB for 240 Volts, 8 way, with 200 Amps rated bus bar, Single Pole & Neutral, , including dismantling taking down unserv. DB complete all as specified and directed Cat No.DBSPN008DD of Make L&T or equivalent Model of Make Legrand/Siemens]

Supply and Fix, miniature circuit breaker (MCBs), DP, 240 Volts,10KA, 40 Amps C curve complete all as specified and directed.

Supply and Fix, miniature circuit breaker (MCBs), single pole, 240 Volts,10KA, 6-32 Amps "C" series complete all as specified and directed.

Taking out existing unserviceable armoured electric cables,1100 volts,cross sectional area 35 sq. mm, 3 ½ core from trenches/ducts/poles etc.,complete all as directed.

Supply and Hanging, ceiling fan, rating 240 V, 50 Hz, Single Phase, 1200 mm sweep with down rod, canopy, fan blades and accessories, BEE 5 Star Rated, all as per Model “ES-50 Premium 5” of Make ‘Havells’ or equivalent Model of Make ‘Usha’/’Crompton Greaves’/’Almonard’ , and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan complete all as specified and directed.

Supply and Laying galvanized steel tubing, 40 mm bore, light grade, in trenches or fixed to poles/Walls etc., for cable protection, complete all as specified and directed.

Materials and Labour for galvanized steel tubing, medium grade, 25 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

M&L for cutting existing GI pipe 40mm Bore (dia) in postion for taking out branch connection 20mm bore dia inserting 1 Nos GI Tee of size 40X40X20 mm including providing new reducting tee ,all joints and jointing materials, including necesary excavation and earth work complete all as directed

Supply and Fix, gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe, 20 mm bore, complete all as specified and directed.

Materials and Labour for earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanised steel earth lead wire 4 mm dia. by means of bolts, nuts check nuts and washers of galvanised steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia. MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown on electrical plate No 3 of SSR Part –I (2009)

M/S SR CONSTRUCTIONS