Construction of Casualty cum OPD Emergency complex at Sub District Hospital Khansahib

CIVIL & SANITARY WORKS

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.All kinds of soil :

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Providing and laying of GSB using nallah material for filling , including dressing of surface to required levels and grades. The work includes collection, carriage, and stacking of Nallah GSB from approved sources, spreading in layers not exceeding 225 mm in loose thickness, watering, and compacting with vibratory roller or any suitable means to achieve required compaction and level. The finished surface shall be firm and properly set for further construction activities. The rate includes mechanical lead upto 15km and head load upto 50mtrs. complete work in all respects as per the directions of the Engineer-in-Charge.

P/L of stone soling incl. ramming,hand packing and all carriages, complete job in ,trenches,foundation etc.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) Mud mat

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer- in - charge. Note: - Cement content considered in this item is @ 330 kg/ cum. Excess/ less cement used as per design mix is payable/ recoverable separately.All works upto plinth level

Dry random rubble masonry with hard stone in foundation and plinth: With bond stone. Incld. Carriages

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer- in - charge. Note: - Cement content considered in this item is @ 330 kg/ cum. Excess/ less cement used as per design mix is payable/ recoverable separately.All works above plinth level upto floor V level

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete at plinth beam level and DPC level Thermo-Mechanically Treated bars of grade Fe-500D or more. Reinforcement @ for all rcc work

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50 mm thick with 20mm nominal size stone aggregate.

FORM WORK Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete.

FORM WORK Centering and shuttering including strutting, propping etc. and removal of form for:Lintel, beams, plinth beams, girders, bressumers and cantilevers.

FORM WORK Centering and shuttering including strutting, propping etc. and removal of form for: Columns, pillars, piers, abutments, posts and struts.

FORM WORK Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platforms.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand) Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 9.149A.1Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm &sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

FRAMES Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):First class kail wood

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.First class kail wood 35MM

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineerin-charge :First class kail wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.4 mm thick glass pane (weighing not less than 10 kg/sqm) incl beeding for glass support.

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.125 mm

Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete. 150x10 mm

Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

CEMENT PLASTER (IN FINE SAND) 12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) Outer walls, Inner walls

6MM CEMENT PLASTER 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)

15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 4 ( 1 cement : 4 fine sand)

Providing and applying Plaster of Paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete

CERAMIC GLAZED TILES Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 1000 ltrs

VITRIFIED FLOOR TILES Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm

TERRRAZO FLOORING 40mm thick marble chips flooring rubbed and polished to granolithic finish, under layer 34 mm thick cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size and top layer 6 mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from 1mm to 4 mm nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 marble chips) by volume including cement slurry and curing complete :Ordinary cement without any pigment.

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade (Area of slab upto 0.5 sqm) 18mm

Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications: Two or more coats applied @ 1.25 liter/10sqm over and including one coat of special primer applied @ 0.75liter /10sqm.

EXTERIOR FINISHING Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

Finishing wall with premium acrylic smooth exterior paint with silicone additives of required shade on New work (two or more coats applied @ 1.43 liter/10sqm over and including priming coat of water exterior paint applied @ 2.20kg/10sqm)

SANITARY WORKS

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: 32 MM DIA

Providing and fixing P.V.C. P & S Trap for water closet or wash basin including P.V.C waste fittings complete:

Providing and filling the joints with spun yarn cement slurry and cement mortar 1:2 (1 cement : 2 fine sand) in S.C.I / C.I pipes 100 mm dia. Pipe,

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete: 100 mm dia. Pipe, Sand cast iron S and S as per IS:3989

Providing and fixing plain bend of required degree:100 mm dia pipe Sand cast iron S and S as per IS:3989 PVC or equivalent

Providing and fixing pvc pipes class c 100 mm dia pipe incl soil waste and vent pipes

PP-R PIPES AND FITTINGS Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge.Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.PN-16 pipe, 16mm OD(SDR-7.4)

PP-R PIPES AND FITTINGS Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge.Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.PN-16 pipe , 25mm OD(SDR-7.4)

Providing & Fixing PVC ( Prince Make) following fittings complete

Door Tee 100mm size

Door Tee 75mm size

PVC collar 100mm

PVC collar 75mm

PVC Reducer 100x75mm

Floor Trap 100 mm size

Plain Bend 100 mm size

Plain Bend 75 mm size

Door bend 100mm

Door bend 75mm

Providing & Fixing following C.P fittings of standard quality & approved make incl. all fixtures etc complete as per directions of engineer in charge

Coupling

Providing and fixing PTMT liquid soap container

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931

Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040mm bowl depth 200mm

P/F of Geysers 50-Litre 2000-Watt Storage Water Heater (White) incl. all fittings and fixtures make: venus, jacquar , racold or equivalent.

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-incharge.

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

TRUSS WORKS

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.Welded

P/F HI ribcolor coated corrugated galvanizedPPGI sheets 1000 to 1020mm cover width 28-35mm high crests at 250 to 255mm TCT (total coated thickness) high tensile SMP Galvalumesteel with silicon modified ployester coating ofapproved colour of total thickness of 35 micron comprising 20 micron exterior coat of SMP over 5micron polyester back coat over 5 micron primercoats on both surfaces incld. side and end lap andusing 8mm galvalume hex self drilling fastener on each crest of sheet for connection with purlins and seam bolts at 300mm centers on all side and end lapps etc. (measured for unit of laid area)0.5mm THICK (TATA,JSW OR EQ brand) I/C ALL CARRIAGES/H/LOAD i/c 60cm wide ridges and valleys wherever required incl. all fittings and fixtures in roof sheeting (TILE PROFILE). (Note:-1.50 is used as a slope factor for sheeting)

ELECTRICAL WORKS

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable of Polycab / Finolex /Anchor / Salzer /RR Cables make to be laid in surface / recessed medium class PVC conduit (25 mm dia PVC Unbreakable conduits of Anchor/Polycab/Finolex/TMT Plus / Paraflex /Ravendera green make. including cutting of walls and refacing of walls to original position with cement concrete ,pop and painting of cutting portion inorder match to existing walls ), with 6 Amps modular switch, modular plate of Anti backteria series ( Anti bacteria series of ABB /L&T /Legrand /Simens make , ) , suitable GI box and earthing the point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.(P+N+E is to be provided sperately for normal and invertor points ) .The job includes providing and fixing of metallic lighting deep junction boxes /Fan deeps (heavy type) Samples to be approved before installation

Wiring for lightl power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable of Polycab / Finolex /Anchor / Salzer /RR Cables in surfacel recessed medium class PVC conduit (25 mm dia PVC Unbreakable conduits of Anchor/Polycab/Finolex/TMT Plus / Paraflex /Ravendera Green make. including cutting of walls and refacing of walls to original position with cement concrete ,pop and painting of cutting portion inorder match to existing walls ) alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. Complete job Samples to be approved before installation

Wiring for Circuits / submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface l recessed medium class PVC conduit as required. of Polycab / Finolex /Anchor / Salzer /RR Cables make.(25 mm dia PVC Unbreakable conduits upto 6 sq.mm and 32/38 mm dia conduits above 6 sq.mm wires of Anchor/Polycab/Finolex/TMT Plus / Paraflex /Ravendera green makeincluding cutting of walls and refacing of walls to original position with cement concrete ,pop and painting of cutting portion inorder match to existing walls ) Samples to be approved before installation

2 X 1.5 sq. mm +1 X1.5 sq. mm earth wire

2 X 2.5 sq. mm +1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire with p/f of Copper thimbles of required size and numbers to be fixed on i/p and op sides dully crimped with termination and rolling of colour coded tape

4 X 10 sq. mm + 2 X 6 sq. mm earth wire with p/f of Copper thimbles of required size and numbers to be fixed on i/p and op sides dully crimped with termination and rolling of colour coded tape

4 X 16 sq. mm + 2 X 6 sq. mm earth wire with p/f of Copper thimbles of required size and numbers to be fixed on i/p and op sides dully crimped with termination and rolling of colour coded tape

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing of 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. ( Anti bacteria series of ABB /L&T /Legrand /Simens make , ) Samples to be approved before installation

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing of 2 No's of 3 pin 5/6 A modular socket outlet and 2 No's of 5/6 A modular switch, connections etc. as required.( Anti bacteria series of ABB /L&T /Legrand /Simens make , ) Samples to be approved before installation

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.( Anti bacteria series of ABB /L&T /Legrand /Simens make , ) Samples to be approved before installation

Supplying & fixing suitable size Gl box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

5/6 A switch

Bell push

indicators

Supplying and fixing following size modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

8 Module (125mmX125mm)

12 Module (200mmX150mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.

8 Module

12 Module

Supplying and fixing of 12-way bell board with allied LED Indicators of standard make dully isi marked

Supply and laying of 25 mm dia medium class PVC medium grade Conduit to berecessed on walls / floor complete with all allied accrues like bends, tees etc. for paving way of laying of wires of haeting points /circuits ,machine points /circuits and sub mains .The Job includes cutting of walls / floors with required hydraulic cutter and refacing of walls with cement plaster of required ratio or with P.O.P after laying of conduits refacing to its original position by way of supply and applying of painting of required colour to effected area's.Anchor/Polycab/Finolex/TMT Plus / Paraflex make.

Supply, Installation, Testing and Commissioning of 1200 mm sweep,BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC)Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factornot less than 0.9, Service Value (CM/M/\N) minimum 6.00,Air deliveryminimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019),THD less than 10%, remote or electronic regulator unit for speedcontrol and all remaining accessories including safety pin, nut bolts,washers, temperature rise=75 degree C (ma><.), insulation resistancemore than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. of Usha /Crompton /Orient /Helonix make

Supply, Installation, Testing and Commissioning of 400 mm sweep,Wall fans , suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. of Usha /Crompton /Orient /Helonix make

Supply, Installation testing and commissioning of 200-250 mm sweep Exhaust Fans of Usha / Crompton / Havel's incl making of necessary connections and making of necessary space in walls / Windows as per site.The Job includes providing and fixing of shutter of suitable size hylum sheet for fixing of exhaust fan of Usha /Crompton /Orient /Helonix make

Supply and fixing of 18 Watts LED surface /recess (Commercial type) downlighter having following specficafications .The luminaire should have a colour temperature of 6500°K, CRI≥80 and SDCM≤5. Luminaire shall be designed to emit initial system lumen output of greater than 2500 lumens with minimum system efficacy of 140 lumen/watt .The downlighter shall be back-lit & not side-lit. The driver shall have THD≤10% (@full Load) and PF ≥ 0.95 (@full load). The luminaire housing should made of pressure die-cast aluminium. The fixture should comply with the parameters as per IS10322. The luminaire shall have impact resistance of IK02 & ingress protection of IP20. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The luminary shall have average life of 50000 hrs operating temperature -10 C to + 45 C The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab & BIS certificate for LED Luminaire & Driver , Approved make Philips / Lighting techology / Trilux /wipro /Endo / Zumtobel / Ligman (to be approved before installation) . The Fixture shall have 5-Years warrenty from OEM for complete repair or replacement of fixtures by new one (Certificate from OEM Shall be submitted before installation) The Agency / firm has to submit Techanical data sheet (TDS) along with above mentioned requisite certificates before supply of materials for approval from department not less than rank of SDO.

Supply, Installation, Testing and commissioning of 2 ft x 2 ft 36-40 watt LED surface/recess mounted Down lighter panels of Standard make dully Isi marke incl making of necessary Connections.The luminaire shall be IP20 & IK02 compliant. The luminaire shall be mandatorily back-lit & not side-lit. LED used shall have life of 50000Hrs @ L70B50, CCT of 6500°K/4000°K, SDCM≤5 & CRI≥80.Luminaire shall be designed to emit initial system lumen output of greater than 5000 lumens with minimum system efficacy of 140 lumen/watt The luminaire driver shall comply to following parameters at 220V to 240V: PF≥0.95 (@full load), THD ≤ 5% (@full load), current ripple≤ 5%, EMI/EMC complaint & in-built surge protection of 4KV. The driver shall mandatorily be housed in metal casing & not plastic casing. The luminaire shall emit minimum initial system lumen output of 5000 lumens with system efficacy of minimum 140lm/w. The input voltage range shall be 140V to 270V.The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports issued by NABL accredited lab before supply of material for approvals: LM79, Type Test report for luminaire, EMI/ EMC compliance test report, surge protection test report & current ripple test report. The bidder shall also submit the LM80 report issued by LED manufacturer, BIS certificate for LED Luminaire & Driver ., , Approved make Philips / Lighting techology / Trilux /wipro /Endo / Zumtobel / Ligman (to be approved before installation) . The Fixture shall have 5-Years warrenty from OEM for complete repair or replacement of fixtures by new one (Certificate from OEM Shall be submitted before installation) The Agency / firm has to submit Techanical data sheet (TDS) along with above mentioned requisite certificates before supply of materials for approval from department not less than rank of SDO.

Supply and fixing of 12 Watts LED surface /recess (Commercial type) downlighter having following specficafications .The luminaire should have a colour temperature of 6500°K, CRI≥80 and SDCM≤5. Luminaire shall be designed to emit initial system lumen output of greater than 1600 lumens with minimum system efficacy of 140 lumen/watt .The downlighter shall be back-lit & not side-lit. The driver shall have THD≤10% (@full Load) and PF ≥ 0.95 (@full load). The luminaire housing should made of pressure die-cast aluminium. The fixture should comply with the parameters as per IS10322. The luminaire shall have impact resistance of IK02 & ingress protection of IP20. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The luminary shall have average life of 50000 hrs operating temperature -10 C to + 45 C The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab & BIS certificate for LED Luminaire & Driver .Approved makes Signify (Philips)/ Igguzini / Lighting Techonology / Endo / Regent /Trilux /Wipro make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 3-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out what so ever reasons

Supply ,installation ,Testing and Commissioning of 10-12 Watts ,2 ft long LED tube light fitting having PVC Body (Commercial type) of standard make dully isi marked ,incl ceiling rose and 2-core transparent wire for connections complete job.The luminaire should have a LEDs with colour consistency SDCM ≤ 5, CRI ≥ 80 and CCT of 6500K. Luminaire shall be designed to emit initial system lumen output of 1400 lumens with minimum system efficacy of 120 lumen/watt. The luminaire shall comply to lifetime of 50000Hrs @ L70B50 with design ambient temp 45°C. The electronic driver used shall have a power factor ≥0.95 and THD ≤10%, suitable for an operating voltage range of 140-270V AC, THD≤10%, Current Ripple ≤5%, Internal surge protection should be minimum 4KV, electrical insulation class should be Class I. The luminaire should be of Class B serviceability. The luminaire should be at least IP20 & IK02 rated. The minimum dimensions of the batten shall be 44mm X 51mm X 1157mm. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, BIS certificate for LED Luminaire & Driver. . , Approved make Philips / Lighting techology / Trilux /wipro /Endo / Zumtobel / Ligman (to be approved before installation) . The Fixture shall have 5-Years warrenty from OEM for complete repair or replacement of fixtures by new one (Certificate from OEM Shall be submitted before installation) The Agency / firm has to submit Techanical data sheet (TDS) along with above mentioned requisite certificates before supply of materials for approval from department not less than rank of SDO.

Supply ,Installation ,Testing and Commissioning of IP66 , 50-60 Watt LED Flood light Luminaries having Aluminium body of of standard make dully isi marked ,to be fitted on walls / poles with necessary cliffs /Clamps with nuts and bolts complete job.The system efficacy of the luminaire shall be ≥140lm/w. The LEDs used in the luminaire shall be from either Lumileds, Osram, Nichia, APT Electronics and CREE make, shall have CCT of 5700°K, CR≥70, SDCM≤5, Life of 50000Hrs @ L70B50. The luminaire shall have IP rating of IP66 & IK rating of IK07. The luminaire shall have lens made of polycarbonate & optical cover made of toughened glass. The LED driver shall have operating voltage range of 140V to 270V, PF≥0.95 @ full load, THD≤ 10% @ full load, In-built surge protection of 4KV, HV Cut off @ 325V (±15V). The luminaire shall have 10KV SPD in-built inside the luminaire. The maximum dimensions of the luminaire shall be, L: 264M, Depth: 52MM & height without cradle: 203MM. The nominal weight of the luminaire shall be maximum 2.4KGs. The luminaire driver & it’s SPD shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material for approval. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, BIS certificate for LED Luminaire & Driver. , Approved make Philips / Lighting techology / Trilux /wipro /Endo / Zumtobel / Ligman (to be approved before installation) . The Fixture shall have 5-Years warrenty from OEM for complete repair or replacement of fixtures by new one (Certificate from OEM Shall be submitted before installation) The Agency / firm has to submit Techanical data sheet (TDS) along with above mentioned requisite certificates before supply of materials for approval from department not less than rank of SDO.

Supply ,Installation ,testing & commissioning of 9 Watts LED Bulk head fittings of Philps /Havels /Bajaj / Wipro make

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/lsolator) of Legrend /L&T /ABB /Schneider / Simens

6 way (4 + 18 ), Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.(But without MCB/RCCB/Isolator) of Legrend /L&T /ABB /Simens /Schinder make

16 way, Double door for lift (Lighting)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioninq etc. as required of Legrend /L&T /ABB / Schneider (Acti 9 series ) / Simens make

Supplying and fixing of 40- 63 Amps rating DP 240/415 volts (10KA) of Legrend /L&T /ABB /Schneider (Acti 9 series ) / Simens make dully isi marked complete with making of necessary connections.

Supplying and fixing of 63 Amps rating TPN 415 volts (10KA) of Legrend /L&T /ABB /Schneider (Acti 9 series ) / Simens make dully isi marked complete with making of necessary connections.

Supplying and fixing of 40 Amps rating TPN 415 volts (10KA) of Legrend /L&T /ABB /Schneider (Acti 9 series ) / Simens make dully isi marked complete with making of necessary connections.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3 1/2 X 185 sq.mm(57 mm)

3 1/2 X 120 sq.mm(45 mm)

3 1/2 X 50 sq.mm(35 mm)

4X25 sq.mm(28 mm)

4X10 sq.mm(25 mm)

Supply,Laying,Testing & Commissioning of 95 sq.mm 31/ 2- core armoured Al Cable XLPE/ PVC Insulated and Steel sheathed of Havells/ Eq. make as approved by SDO , , including cost thimbles on input aswell as output sides dully crimped with hydraulic crimping tool incl making of necessary connections. (Quantity is tentative and is subject to site requirement in consultation with EIC)

Supply,Laying,Testing & Commissioning of 50 sq.mm 31/ 2- core armoured Al Cable XLPE/ PVC Insulated and Steel sheathed of Havells/ Eq. make as approved by SDO , , including cost thimbles on input aswell as output sides dully crimped with hydraulic crimping tool incl making of necessary connections. (Quantity is tentative and is subject to site requirement in consultation with EIC)

Supply,Laying,Testing & Commissioning of 185 Sq.mm ,31/2 core armoured Al Cable XLPE/ PVC Insulated and Steel sheathed of Havells/ Eq make as approved by SDO , including cost thimbles on input aswell as output sides dully crimped with hydraulic crimping tool incl making of necessary connections (Quantity is tentative and is subject to site requirement in consultation with EIC)

Earthing with G.l. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoall coke and salt as required.The job includes providing and fixing of main hole PVC Chamber with its cover (12 inch dia) complete job

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable to be laid through existing recessed PVC conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.( Anti bacteria series of ABB /L&T /Legrand /Simens make , )

Telephone Socket (RJ11)

Supplying and fixing following size modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

2 Module (75mmX75mm)

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cost of pvc saddles etc to be fitted on ceiling

Providing and laying of shock proof Rubber mats of 2mt. x 1 mt. and 12 mm thick in size of standard make dully isi marked

Krone type MDF with top and bottom entry for cables, MS powder coated to accommodate IPM

Supplying and drawing in existing conduits / cable tray / raceway and testing & commissioning of following multicore PVC insulated PVC sheathed annealed tinned copper conductor 0.5 mm dia telephone wires conforming to ITD-S/SW-113B including terminal joints complete as required.

Mechnical Items

Supply, Installation, Testing & Commissioning of Modular type Variable Refrigerant Plow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having 100% hermetically sealed Inverter type twin Rotary/Scroll Compressor(s).minimum two compressors (with Individual separate PLB) for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with suitable foundation etc. complete as required. To have better efficiency condenser fan shall be capable to operate at different speed with respect to load. The unit shall deliver the rated capacity and in confirmation as per IS 18728:2024 and CPWD Specifications and work even at 50°C ambient temperature without tripping. The system shall be able to deliver 100% of the rated capacity upto 39 Degree Celcius. The unit shall be suitable to work on 400V +/-10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall performance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity >40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building for colling or Heating or Both

Supply, Installation, Testing and Commissioning of following minimum capacity High wall type Indoor unit equipped with and comfort washable (hot/cold)synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50Hz, single phase AC supply, complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. Thesystem shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of outdoor

Supply, Instañama, Testing and Commissiening of following mum capacity 4-way compact VRV/VRF Cassesse Type Indoor catting moumed unn equipped with eynthetic washable medie ne Fixer, fan acction with low notes fan/dynamically balanced blower multispeed motor, con section with DX Copper coll, electronic rapanston valve, outer cabinet, drain pump, grifi.necessary supports vibration Isolation, Caciled cemate.contcal etc, suitable for operation on single phase 230 V a 10%, 50ts AC supply, complete, as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The system shall be capable to adjust air flow as per room requirement automatically The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C Dll and 19 Degree C Wil temperature (Make will he same as of Outdoor)

Supply, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer (OEM) make as of ODUs and IDUS

Indooer Units

Outdoor Milti Joint

Supply, Installation, testing and commissioning including vaccumlatation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-0 closed cell elastomeric nitrile rubber tubular sleeves sections of 19 mm thick Insulation as given below for Suction and Liquid lines, all accessories as per specifications etc. as required:

28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm

25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm

22.2 mm dia (OD) (llard drawn) with tube thickness 1.2 mm

19 mm dia (OD) (liard drawn) with tube thickness 1.2 mm

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

DRAIN PIPING Providing and fixing rigid CPVC piping complete with fittings, supports as per specifications and duly insulated with 6mm thick closed ceil nitrile rubber insulation.

25mm dia

32 mm dia

Control Transmission Wiring Providing & fixing control wiring of 2 core x 1.5sqmm copper in PVC conduit pipe of 25mm dia including providing & fixing support 1.5mt distance CIC where it is not recessed between indoor units and outdoor units

Supply, Installation, testing & commissioning CPRI Approved of Gi Electrode Earthing with 50mm dia and 3 meter length, with 3mm thick the electrode should be hot-dip galvinised. The Gi Electrode shall be pre-filled with Crystalline Conductive Material (CCM). The Gf electrode shall be surrounded with BEE MOIST compound to provide maximum contact between the electrode and compound should be eco-friendly and having ROHS certification GI Electrode Earthing should be maintenance free and does not require regular manual addition of water GI Electrode and providing and laying of 2 Nos of 25 x 5 mm Gl strip from GJ rod upto the panel. The earthing pli should be covered with PVC cover

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below w. ground as strip earth electrode, including connection/terminating with Gl. nut, bolt, spring, washer etc., as required

Wiring for Circuit/Submain Wiring along with earth wire with the MS following Stars of FRLSPVC Insulated copper conductor single core Cable in surface/Recessed medium class PVC conduit as required

4x16 sq mm+2x6 sq ramyearth wire

Supplying and installing following size of perforated painted with powder coating MS. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with twonembers MS/Or Suspenders/e base of suitable size MS/Gl angle, bolts & nuts, painting suspenders, fastener etc as required

150 am width x 50 mm úcpth X 1.6 mm thicknes

100 mm width x 50 mm depth X 1.6 mm thicknes

Supplying and Laying of 1 No. PVC/XLPE insulated and PVC, Sheatheil XLPE Power Cable of 1.1 KV Grade of Following Sizes in the existing Cable Tray/RCC/Ilume/DWC/Stone ware/Metal Pipe as Required. 3.5 CX 185 Sq.mm Aluminium Armoured

Supply and Making end Termination with Brass Compression Gland and Aluminium Lugs for the Following Sizes of PVC insulated and PVC Sheathed/XLPE Aluminium Conductor Cable of 1.1 KV Grade as Required (Comet) 36 X 185 sq.mm

Providing and fitting of snow/ bird protection hood in 22 gauge Gl sheet with 1 inch wire mesh duly spray painted for ODUs.

Additional Refrigerant charging R-410A of entire VRV system and commissioning

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on 24 surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 243 Sway (4+24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 KA, C curve miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections. testing and commissioning etc. as required.

Single Pole

Single Pole and neutral

Supplying and fixing following rating, Four pole. 415 V, 10 Ka NS MCB in the existing MCB DB complete with connections, testing and commissioning etz. as required 32 A F.P MCB 10 Ka "C" Curve

Wiring for Circuit/Submain wiring alongwith each wiere with thefollowing sizes of FRLSPVC insulated copper conductor single cosre cable in surface/ Receased meadium class PVC condut as required

2x235 sq.m, +1x2.5 sqm earh sire

4x16 sq.mm +2x6 sq.m earth wre

Supplying installation, wating and commissioning of electric driven 450 Ipm at 35 m Head terrace pump conforming to 18 12459: 2019 suitable for automalle operation Horizontal type, multistage, centrifugal, split casing mechanical of cast seal iron as body required. & bronze Suitable impeller HP squirell with stainless cage induction steel shaft motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP65 class of protection for enclosure, horizontal foot mounted type with Class- F'Insulation, conforming to 19-12616: 2018.M.6. fabricated remmon baso plato, coupling, coupling guard, foundation boits etc.as required, Bultable cement concrete foundation duly plastered and with anti vibration pads.

Supply, Instaliation, testing & commissioning of Black steel pipe (IS 1239 Part-1) heavy C-glass including cutting, threading, welding etc. bends, elbows reducers, clamps, hangers etc. including cutting holes in brick or RCC -7 walls/slabs and making good the same complete Including the cost of structural work for supports fabricated from standard sections of required sizes and thickness eg MS rods, angles channels, slotted angle, etc., cutting to sizes, drilling welding fixing to insert plates, including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and red shade including all steel work 100mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe 7.7 conforming to IS 1239/Class-li of IS: 3589 including Welding, fittings like elbows, tees, flanges, tapers, nuts boits, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coals of synthetic enamel paint of required shade complete as required

80mm dia

65mm dia

50mm dia

40mm dia

32mm dia

25mm dia

Supplying and fixing single headed internal hydrant valve with Instantaneous 79 Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type-A) with blank Gunmetal/Stainless Steel cap and chain as required

Single headed Gunmetal

Supplying, fixing, testing and commissioning of butterfly valve of PN 16 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to iS 13095 of following sizes as required

50mm dia

80mm dia

100mm dia

Supplying, fixing, testing & commissioning of double flanged sluice vaive of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complain with nuts, holts, washers, gaskets and conforming to 15 780 of following sizes as required 100mm dia

Providing installation, testing and commissioning of non-retum valve of following sizes confirming to 15 5312 complete with rubber gasket, Gi bolls nuts, washers etc as required: 100 dia

Supplying and fixing orihice piate made out of 8 mm thick stainless steel (Grade 304) with artililee of required size to be filled between fange & landing valve of external and internal hydranis to reduce pressure at the outlet to the level of 3.6 sg/cm².complete as required

Supply, installation Testing and commisioning of pressure gauge of 0-10 kg/sq cm range with cut-off bronze ball valves of suitable size with all accessories as per direction of Engineer-in-charge

Supply, Installation, Testing and commisioning of pressure switch with cut-off bronze ball valves with integral stainer and flare nut (mired ends) of suitable size will all accessories and cabling as per direction of Engineer-in-charge

Providing, installation, testing and commissioning of stainless steel Y-strainer tabikaled out of 1.8 mm thick stainless steel Grade 304, sheet with 3 mm dia holes with stainless steel flange. 100mm dia

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical geng bell to sound continuous alarm when the sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain volve and bypass, test control box, ball valves, MS pipe of required size flanges, orifice plate, gasket etc of follwing sizes as required 80mm dia

Supplying & foảng 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzie conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required Gun metal

Supplying and foxing 63 mm dia. 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with Gl wire, rivets etc. conforming to IS 636 (type A as required Gun Metal

Providing, supply and foxing of MS hose box of suitable size (2100 mm X 900 mm X 250 mm) to accommodate 2 no of 15 mtr, 01 no of 30 mtr long fire hose fireman axe, fire extinguisher 2 and a branch pipe, wall mounted type as per direction of Engineer in charge

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete, 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type 2 as per IS: 12585, 20 mm nominal internal dia gun metal globe valve & nozzle, Drum and brackets for foxing the oquipmets on wall, Connections from riser with 25 mm dia stop gun metal valve & MS. Pipe and socket. 30 Mtr long

Providing and foxing standard fireman's axe with heavy Insulated rubber handle conforming to IS: 926 complete

Supply, Installation, testing and commisioning of C.125 mm single air relief valve with stop cock conforming to IS: 14845/2000 with iSi mark for water works purpose including fixing the same with hydrant riser including testing & commisioning the system etc all complete as per approved specification & direction of Engineer in charge

Supplying and fixing of the bridgade connection cast iron body with gun metal male instantaneous iniet couplings complete with cap and chain as regd for suitable dia MS pipe connection conforming to 18 904 as required 2 way-100 mm dia M.S. Pipe

Providing foxing, testing & commissioning of 15mm dla quartzoid bulb type sprinkdors of rating 68 degree centigrade with required accessories Pendent Sprinkler

Supply, installation, testing & commisioning of 25 mm SS ball Valve

Fabrication, supply, installation, testing and commissioning post hydro testing of 10,000 liters M.S overhead water tank( 12ft X 7FT X 4.5 FT) made up of MS Plates IS 2062 E250 with thickness of (6 mm bottom, 5 mm sides, 4 mm top) incl. cutting, fabrication & erection Stiffeners (ISA 50×50×6), stay rods, gussets incl. erection Nozzles (inlet 50 mm, outlet 80 mm, overflow 80 mm, drain 50 mm), manhole with cover (welded). The tank shall be duly Finished with Epoxy paint, internal epoxy paint (primer + 2 coats). PCC 1:2.4 (20mm agg) levelling course 50 mm thick over existing slab including all carriages complete job. Minor foundation leveiling PCC 1:2:4 (50 mm) with bonding coat & surface preparation inci carriage complete

Providing and wraping of Aluminium laminated glass wool insulation of minimum thickness 50 mm on header pipes and terrace water storage tank. The job further includs painting with two or more coats of synthetic enamel paint of required shade complete as required:

100mm width x 50mm depth x 2mm thick perforted MS cable trays including horizontal and vertical bends, reducens, lees, cross members and other accessories as required and duly suspended from the celling with M.S suspenders and including painting etc. as required

Providing and supplying of aliminators suitable for raw water upto 450C temperature working pressure 5.5 kg/cm2 and test pressure 10.0 kg/cm2 with unil control including nuts, botts matching flanges (screwed or welded) complete with 1.5mm thick compens astilstos gasket of same rating 100 mm dia or as per nominal pump dia

Providing/Fitting of 3.5 core, 50 sq.mm armored Al, XLPE insulated cable for connecting power source to control panel along with clamps wherever required conforming to IS: 7098.

Providing earthing stalion with Gi Earthing Plate (600mm x 600mm) 8 mm thick for pumps and MCC panels including excavation, Cl manhole cover and frame complete as per specifications and IE rules

GI Strip of following sizes 25 x 6 mm G

Fire Extinguisher System Supplying, installation, testing and commisioning of ABC type fire extinguisher of 6 kg capacity including cost of all material & labour etc complete

Portable fire Extinguisher system supplying, Installation, tyesting and commissioning of CO2 type fire Extinguisher 4.5 kg capacity confirming to 15. 2878 made from ISI marked seamless cylinder confirming to IS: 7285, fitted with ISI marked controlled valve conforming to IS: 3224, high pressura 1 mir discharge hose & horn complete with initial gas charged with carrying handle & wall mounting bracket as per direction of engineer in charge

Supply, installation, testing and commisioning of Mechanical Foam type 9 litre capacity fire Extinguisher, ISI marked, IS: 10204, containing 540 ml AFFF liquid ISI marked, IS: 4989 part li and a polyurethane coated CO2 gas cartridge, ISI marked, IS: 4947 complete with gun metal union cap, nylon hose with plastic foam making branch and wall mounting bracket as per direction of Engineer in charge

Supply, Installation, Testing and Commissioning of 20 passenger cum bed Lift (as per manufacturer design & as per detailed specification below conforming to 15 specifications) and putting inin operation after final testing in the existing shaft complete with all pther incidental works thereof included necessary for successful commissioning of lift The Defect Liability Period (DLP) for the equipment shall be one (01) year from the date of successful commissioning of lift. Type: MRL type Passenger Lift Load: 20 Passengers/1360 Kg. Control: Microprocessor based simplex full collective with or without attendant. Controller in shaft and user interface in landing Drive: VVVF Drive with feedback control (closed loop) Machine: Energy Efficient Machine, Gearless machine located in the shaft on the top of Guide rails (To be provided by successful bidder) Power supply: AC 400/415V, 3 Phase, 50Hz Speed: 1 m/s Floor Served: G+1 (2 Stops) Landing: 2 landings; All on same side Total Rise: 3.6 Mtr. (approx.) Main Wire Rope/Belt: As per manufacturer's standard conforming to relevant IS. Signals: Digital Car position indicator, car travels direction indicator in car and at all landing with call registration indicator. COP & LOP must have stainless steel face plate silver brushed with surface mounted button with braille. Button: All buttons in car and landing including door open and close buttons in COP shall be luminous & encoded with braille on/off switch for Lift, fan, light, toggle switch or key switch for automatic/attendant mode of operation. Display type: Monochrome/ Colour LCD/Segmented LCD/ Scroll. Operation Push Button for litt maintenance & service should be on top of the car. Travelling Accuracy: ± 5mm (Micro Leveling Arrangement) CAR:- Car Group: one car simplex Design: Stainless steel in hairline finish. Car Inside: Suitable for carrying minimum 20 passengers. Car Entrance: Clear Opening 1100 mm-1200mm (W) x 2000 mm-2100mm(H) protected with car door. Door: Car Stainless Steel Centre Opening (COPD) automatic door provided with V3F controlled door drive system with 2D Infrared Curtain of light & Mechanical Force Limiting Device Landing Door: Stainless Steel Centre Opening (COPD) automatic door provided with V3F controlled door drive system with fire rating of 120 min. Door Opening: Stainicas steel Automatic Power operated door ith 2 panel automatic contor opening with full length photocell assembly curtain sensor. Round Handrail in Stainless steel finish provided on rear wall of car. Flooring of car shall be provided of material with good traction such as vinyl. The flooring material should be durable enough to withstand constant foot traffic. PROTECTIVE DEVICES & OTHER ACCESSORIES: - ARD: Automatic rescue device complete with dry maintenance free batteries as required for automatic evacuation to the nearest floor in case of power failure/single phasing/others. Overload Protection: Fully loaded with overload protection. Under overloading condition, the lift car must not start with door remaining open and give audio & display indication. Emergency Lighting in Car: Battery operated emergency lighting in the lift car. Intercom System: Battery operated Intercom System in Lift Car. Emergency Alarm: Battery Operated alarm bell system in Lift Car & Control Room. Buffer springs and Guide rails: to be provided as per OEM recommendations. Fireman switch: Fireman switch placed at ground Floor. Voice Synthesizer: Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the lift. Wire/Belt condition monitoring/inspection drive. Auto fan Cut-Om. Motor overheat protection, Phase failure and phase reversal protection Automatic operation for car fan Anti-nuisance(empty car) Anti-nuisance (car call cancellation at direct/on reversal Blower fan in car for ventilation Door nudging Full load bypass Lift Shaft electric lighting system along with 16 amp 3-pin sockets and switches. Suitable number of Earthings for lift as per the OEM to be provided. Further, the successful bidder shall provide all other items/accessories in addition to above that are necessary for proper working of lift

Waterproofing of elevator pit: Providing & Laying of integral Cement based waterproofing (Injected type) treatment including preparation of surface and then applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water proofing compound conforming to IS: 2645. Απει proper curing apply a second coat of cement slurry mixed with proprietary water proofing compound. The job includes finishing the surface with 20mm thick joint less cement mortar of mix 1:4.

Earthing: Providing and Laying of Copper (cu) strips and cu plate for proper earthing of all Electro-mechanical components carrying main current, including but not limited to the motor and electric panel. Use of bolts or screws and cu strips to establish grounding connections on each component. The job includes earth work by using labor for making a pit of suitable size for proper earthing and after that laying copper plate of minimum size 60cm width, 60 cm height and 3.15mm thickness and filling the pit with chemicals (chemical earthing). The earthing cu strip must have cross section not less than 24 mm^2. The job further includes laying of perforated conduit pipe from ground up to cu plato having funnel at top as per actual requirement at site & as per IS 3043 (1987)

Providing/Fitting of 4 core, 16 sq.mm XLPE insulated armored Copper cable for connecting Lift panel to the changeover panel duly thimbled and PVC tapped ends in different shades using Crimping tool along with conduits /cable trays & clamps wherever required conforming to IS: 7098.

Carriages for Different Materials

Crushed Aggregate Avg Lead of 15kms

Sand Avg Lead of30kms

Bricks Avg Lead of 20kms