SPL REPAIR OF 04 X OFFRS ACCN IN SECT D AND PROVN OF 02 X AC FOR COMPUTER ROOM (CAPACITY 1.5 TON) OF BLDG NO T-29 AT DINJAN MIL STN UNDER GE DINJAN

Amount

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for Reinforced cement concrete (Nominal Mix) 1:2:4 type B1 (using 20 mm graded stone aggregares) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Cutting channels, grooves or rebates n exc 15cm girth , and trimming surface without reinforcement complete all as specified and as directed.

Demolition of brickwork or stone/ boulder masonry, built in Cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar in 1:6 complete all as specified and as directed.

M&L for cutting chases, pinning in brickwalls, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20 cm girth complete all as specified and as directed.

M&L for 20 mm thick Granite (of any type) work (table rubbled and polished) in steps, Jambs, Pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm screed complete all as specified and directed.

M&L for use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizonal or sloping) for flat rough finished surfaces of concrete complete all as specified and as directed.

Dismantling of unframed timber scantlings 40 sq. cm and over in section, in any position complete all as specified and as directed.

M&L for 2nd class hard wood in scantlings wrought timber fixed complete all as specified and as directed.

M&L for Designer Beading for Plywood 18/19 mm Thickness fixing with Glue and nails to Plywood Works complete all as specified and as directed.

Taking down the Chowkhats or frames exc 1.5 sqm but n exc 4 sqm each (without taking off shutters from the frames) complete all as specified and as directed

Taking down the Chowkhats or frames not exc. 1.5 sqm each (without taking off shutters from the frames) complete all as specified and as directed

Refixing of shutters of any description in same opening n exc 1 sq. m each complete all as directed.

Refixing of shutters of any description in same opening exc. 1 sq.m and n exc 2 sq. m each complete all as directed.

S&F Pressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and as directed.

S&F Pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and as directed.

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded aggregate) as in hold fast and filling of steel chowkhat etc. complete all as specified and directed.

M&L for PCC in 1:2:4 Type B0 ( 12.5 mm graded aggregate) asin lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs,, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, filling of pressed steel door frames complete all as specified and directed.

S&F 35mm thick, glazed/skelton shutters with second class hard wood,open rebated and prepared to receive glass, gauge, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc, sizes of members of shutter as specified in SSR Part I Section 8, clause 8.24 (a) complete as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

M&L for Block Boards 18/19 mm thickness, grade 2 quality, interior grade, commercial type, with decorative face veneers on both faces; fixed with 7.5 cm long screws.

S&F Factory made Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed.

S&F 100 mm long Aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm long Aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F 100 mm long Butt hinges, medium weight, cold rolled mild steel fixed to Chowkats complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and directed.

S&F 375 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F 150mm long Extruded Aluminium Handle, fabricated type, anodised complete all as specified and as directed.

S&F in repair 150mm long Extruded Aluminium Handle, fabricated type, anodised complete all as specified and as directed.

S&F 125mm long Extruded Aluminium Handle, fabricated type, anodised complete all as specified and as directed.

S&F in repairs Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and as directed.

S&F Floor door stopper (Overall length of cover plate 140 mm) of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with MS fillets and stainless steel wire staples complete all as specified and as directed

S&F mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F for mild steel flat iron as in hold fast 25x6 mm confirming to Fe 290 Gde E-165 complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia and over ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed

S&F for Joist, channel, angle, or tee sections of Fe 290 (Gde E-165) fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and as directed.

S&F for Anodised aluminium ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed.

S&F for 8 mm thick aluminuim duco grill size 75x75 mm fixed to windows or ventillators with aluminium flat 30x3mm complete all as specified and as directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed.

S&F for aluminium anodised snap grid frame work of size 605mm x 605mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frame including providing two coats of distemper oil emulsion complete all as specified and as directed.

M&L for Water proofing treatment on RCC roof etc. comprising with the following operation & as specified herein below:- (a)Taking down existing old tarfelt, bituminous compound including cleaning & removing debris to a distance exc 100 m n.exc.250m. (b) M&L for 15 mm thick cement mortar in 1:4 finished even and smooth. (c) Preparing & cleaning of fully dried cement plastered surface. (d) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 litres per sqm conforming IS-3384. (e) A layer of APP based polymeric membrane membrane 3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyster non woven fabric (weighing not less than 160 gms/sqm) shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction. (f) One coat of aluminium paint over APP membrane @0.11Kg/Sqm. Note:- Prior to execution of the APP Membrane works, leak proof test shall be done by ponding water on roof slab to minimum depth of 25 mm. The entire roof slab shall be flooded with water for 48 hours. The necessary barrier shall be made to make feasible to stagnate water for 48 hours on roof slab.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc) sheets in roof coverings complete all as specified and as directed.

S&F for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed

Demolition of unreinforced cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 75 mm thick Cement concrete type C-2, 1:3:6 (40mm graded aggregate) in plinth protection, finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade A complete all as specified and as directed

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as directed.

M&L for light shade vitrified Ceramic tiles 10 mm thick (Square/rectangular) polished, area of each tiles exc 0.36 sqm but n exc 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed in CM 1:6 complete all as specified and directed.

M&L for light shade vitrified Ceramic tiles 10 mm thick (Square.rectangular) polished, area of each tiles exc 0.36 sqm but n exc 0.42 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick backcoat in CM 1:4 complete all as specified and directed.

M&L for Non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed in CM 1:6 complete all as specified and directed.

M&L for Coloured Glazed ceramic tiles in vertical surface of size 450X 350X 7 mm thick over 10 mm thick back coat of cement mortar in 1:4 set and jointed in neat cement slurry and pointed in white or colour cement to match over complete all as specified and as directed.

M&L for taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for rendering 10 mm thick internal wall on fair faces of brick work or concrete surfaces in cement Mortar in 1:6 and finished even and smooth (without using extra lime or cement)complete all as specified and directed.

M&L for rendering 20 mm thick on fair faces of external wall of brick work or stone surfaces in two layers (10 mm and 10 mm thick) in cement Mortar in 1:4 using water proofing compound in top layer as per manufacturer's instruction and finished the surface even and smooth without using extra lime or cement complete all as specified and directed. (Note: WPC shall be measured and paid separately as supply only)

Supply only Liquid water proofing compound for external wall plastering (for 5 mm thick plastering) complete all as specified and directed

M&L for rendering 5 mm thick in cement mortor (1:3) on concrete surfaces as in ceilings (sunshed, chajja etc) and finishing surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for preparing newly plastered surfaces of walls, etc and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for preparation newly plaster surfaces of wall, chajja, facia etc and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistant as per IS-15489:2004 alkali and fungal resistant exterior paint of required shed (company depot tinted) with silicon additives 1.43 litrs/ 10 Sqm over and including primer coat of exterior primer applied 0.90 litre/10 Sqm over new surfaces using Airless spray technology with maximum working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and acessories complete all as specified and directed.

M&L for complete removal of existing treatment from walls by scrapping with mechanical wall sander (having mechanical vaccum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistant as per IS-15489:2004 alkali and fungal resistant exterior paint of required shed (company depot tinted) with silicon additives 1.43 litrs/ 10 Sqm over and including primer coat of exterior primer applied 0.90 litre/10 Sqm over new surfaces using Airless spray technology with maximum working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and acessories complete all as specified and directed.

M&L for preparing old decorated surfaces of walls by complete removal of existing treatment and applying two coats of distemper-oil-emulsion over a coat of primer including 1.5 mm thick wall care putty complete all as specified and as directed.

M&L for preparation of old decorated plastered surfaces of walls by brooming down or steel wire brushing, scraping down with steel scraper, smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and as directed.

M&L for preparation of old decorated plastered surfaces of ceiling by brooming down or steel wire brushing, scraping down with steel scraper, smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and as directed.

M&L for Preparation of new or untreated surfaces of wooden surface of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over pink primer complete all as specified and as directed.

M&L for preparation of old painted wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections complete all as specified and as directed.

Taking up or down 25 mm bore steel tubing and connections complete all as specified and as directed.

Supply and laying of 16mm of CPVC pipes SDR 11& Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. tranches complete all as specified and directed.

Supply and laying of 20mm of CPVC pipes SDR 11& Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. tranches complete all as specified and directed.

Supply and laying of 25mm of CPVC pipes SDR 11& Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. tranches complete all as specified and directed.

S&F for 16mm dia CPVC Brass thread elbow complete all as specified and as directed.

S&F for 20mm dia CPVC Brass thread elbow complete all as specified and as directed.

S&F for 25mm dia CPVC Brass thread elbow complete all as specified and as directed.

S&F for 16mm dia CPVC Brass thread Tee complete all as specified and as directed.

S&F for 20mm dia CPVC Brass thread Tee complete all as specified and as directed.

S&F for 25mm dia CPVC Brass thread Tee complete all as specified and as directed.

S&F for 16mm CPVC Brass thread union complete all as specified and as directed.

S&F for 20mm CPVC Brass thread union complete all as specified and as directed.

S&F for 25mm CPVC Brass thread union complete all as specified and as directed.

S&F for 16mm CPVC ball valve complete all as specified and as directed.

S&F for 20mm CPVC ball valve complete all as specified and as directed.

S&F for 25mm CPVC ball valve complete all as specified and as directed.

S&F for 25mm CPVC tank adopter complete all as specified and as directed.

Dismantling of water tank Capacity exc 500 not exc 1000 Ltrs and removing to store complete all as specified and as directed

Hoisting and Fixing of rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 1000 ltrs hoisted and fixed in position specified in SSR Part I complete all as specified and as directed.

S&F in repairs for bib taps fancy type CP with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferule and fixed of size 15mm bore in repair complete all as specified and as directed.

S&F in repair pillar taps of size 15mm, chromium plated fancy type cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and as directed.

S&F in repairs 15 mm bore dia cast copper alloy fancy type, chromium plated stop valves, crewed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repairs 15mm stop valves (concealed type), cast copper alloy fancy type chromium plated, long sunk and cup, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F for 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F for 20 mm bore, Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F in repairs 15 mm bore Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm?125gms) complete all as specified and as directed.

M&L for 32 mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

S&F 15mm dia Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms) complete all as specified and as directed.

S&F for Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed.

S&F for Grating doom 125mm dia of PTMT (Minimum weight 40gms) complete all as specified and directed.

S&F in repairs for PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and as directed

S&F in repairs110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed

S&F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed

S&F in repairs 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed

S&F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed

S&F for 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed

S&F for 75 mm bore PVC (SWR) bends any radius complete all as specified and as directed

S&F for 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed

S&F for 75mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed

M&L PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement including disconnection of old existing trap, and connected with existing water pipe complete all as specified and directed.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and as directed

S&F in repairs PVC low level flushing cistern 10 litre capacity, valveless, symphonic action type with inlet, ball valve, float and handle incl bracket, PVC conection pipe and flush pipe of polyethylene of low or high density or PVC. 32 mm dia complete all as specified and directed

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed

S&F for Brass chromium plated shower rose 125 mm size fixing to steel pipe or union complete all as specified and as directed

S&F for Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed

S&F in repairs vitreous china wash hand basin white flat back size 550x400mm excluding taps, waste chain and plug and porcelain stopper including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and as directed.

S&F in repairs soap dish vitreous china coloured approximate size (160mmx160mmx90mm) complete all as specified and as directed.

S&F Tubular towel rail, 20mm dia, D type, 60cm long Brass Chromium plated between flanges complete all as specified and as directed

Supply and fixing in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F for PVC corner shelf complete all as specified and as directed. Make : Cat No. T6010A1 of Parryware or equivalent model in Make Hindware / Cera/Prayag.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5 KVA complete all as specified and directed.

Taking down carefully unserviceable aluminium/copper point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets light fitting etc for taking credit removing from site and making good disturbed surfaces of walls, floors, etc using cement mortar (1:3) complete all as specified and as directed.

Materials and labour for concealed point wiring with two runs of FRLSH PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of size 1.5 sqmm and one single core FRLSH PVC insulated unsheathed stranded copper conductor of size 1.50 sqmm green in colour as earth lead, drawing through in and including PVC rigid conduit of size not less than 20mm, with all fittings & accessories including provn of MS sunk terminal box of appropriate size suitable for switch fixed flush to wall for mounting switch, sockets, fan regulators etc with 3mm thick hylum sheet top cover with screws & cup washers for one light / fan point / call bell controlled by one switch one way 5 Amps complete all as specified and directed . NOTE : Cost of cutting, chieseling, and making good the disturbed surfaces (if any) matching with the existing surface is deemed to be included in the unit quoted rates.

All as per item No 130 here-in-above but one 5 pin switch socket combination, 5 Amps on Independent board.

All as per item No 130 here-in-above but one 5 Amps, 3 pin socket outlet on the same board with other switches.

All as per item No. 130 here-in-above but wiring with cables of size 2.5 sqmm & cables of size 2.5 sqmm as continuous earth wire for one 15/16 amp multi socket out let on independent board complete all as specified and directed by Engineer-in charge.

S&F for modular switch 1 way 6 A, 1 Module ISI marked complete all as specified and as directed.

S&F for modular Bell push 1 way 6 A, 1 Module ISI marked complete all as specified and as directed.

S&F for modular switch 1 way 16 A, 1 Module ISI marked complete all as specified and as directed.

S&F for modular socket 6-A, 2/3 Pin combined 2 module ISI marked complete all as specified and as directed.

S&F modular socket 6 A/16 A, 2/3 Pin combined 2 module ISI marked complete all as specified and as directed.

S&F modular fan regulator step Type 120 Watt, 2 Module ISI marked complete all as specified and as directed.

S&F for ceiling rose, 3 Terminal/PVC/ polycarbonate, isolated body including suitable PVC block/box complete all as specified and as directed.

S&F lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings with 9W bulb complete all as specified and as directed.

S&F for 20 Watt surface and wall mounting type LED batten with polycarbonate housing & integrated complete all as specified and as directed.

S&F in repair 9/10 W surface and LED wall bracket light aesthetically designed with B22d & E27 lamp holder with polycarbonate housing and intigrated electronic driver complete all as specified and as directed.

S&F Factory made board distribution (DB) Double Door in sheet steel enclosure with common bus bar at incomming end, SPN, 12 way, 240 Volts , 200 amps suitable for housing MCBs complete all as specified and directed.

S&F MCB, 'C' Series, SPN, 240 Volts, 6 to 32 Amps, 'C' Series, 10KA capacity complete all as specified and as directed.

S&F MCB, 'C' Series, SP, 240 Volts, 6 to 32 Amps, 'C' Series, 10KA capacity complete all as specified and as directed.

S&F in repair, single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of 20 Amps rating complete all as specified and as directed.

S&F 35 Watt LED building security light new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embeded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08. including all fixing arrangement and taking down old light fittings of any type complete all as specified and as directed.

S&F street light bracket arm of length not less than 1.5 m made out of GI tubing, 32 mm bore, light grade fixed to pole, etc with suitable size flat iron clamp, nuts, bolts including painting with two coats of aluminium paint over a coat of red oxide, zinc chrome primer on steel surfaces complete all as specified and as directed.

M&L for concealed sub main wiring with two run of 6 Sqmm (Nominal area) single core cable PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC conduit medium grade of suitable size, fixed to wall/ceiling etc including one run of 6 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor (FRLSH) as earth continuity conductor drawn through and including one run of PVC conduite heavy duty and connected accessories including cutting and chases etc, and connecting to common earth dolly, complete all as specified and as directed. Note : (a) Two runs of main cable, one run of earth continuity conductor cable and one run of PVC conduite will be measured as one unit for payment purpose.

M&L for earthing complete with GI earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers protected by 15mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT steel bars @15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and salt in alternative layers,necessary earth work in soft/loose soil all as shown in Electrical Plate No 3 of MES Schedule Part I and testing complete all as specified and as directed.

Supply & fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB complete all as specified and directed.

Material & labour for Sub main wiring with two runs of single core 6 Sqmm (Nominal Area) FRLSH PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC casing capping of adequate size fixed on surface of wall/ceiling with all necessary fittings and accessaries and 1 run of FRLSH PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 6 Sqmm as earth wire (green in colour) run through PVC Casing capping and connected common earth dolly including taking out the old sub main wiring for connection to DBs/dolly shall be deemed to be included in this item and Two runs of 6 Sq mm as current carrying conductor and one run of 6 Sq mm as earth conductor PVC casing capping shall be measured as one run for measurement, complete all as specified and directed.

Supply and install hi wall split units indoor/outdoor of capacity 1.5 ton complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2.of capacity 1.5 Ton complele as directed.

M/S CHANDAN ENTERPRISE (BID ID -3105914)

G S Enterprises & Co (BID ID -3107691)

FREEZCON (BID ID -3106627)

Shree Trilok Electric Corporation (BID ID -3107589)

M/S A K ENTERPRISE (BID ID -3102439)

MAZUMDAR ENTERPRISE (BID ID -3106556)

M/S BORAH BROTHERS (BID ID -3107933)