REPAIRS TO ROOF FLOOR INCLUDING SUNKEN FLOOR REPLACEMENT OF SANITARY AND PIPE FITTINGS CEILING JOINERY AND INTERNAL WATER SUPPLY IN CERTAIN BUILDINGS AT ARMY AREA COIMBATORE UNDER GE WELLINGTON

Amount

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutters (without taking off shutters from the frames) all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutters from the frames) area exceeding 1.5 Sq mtr but not exceeding 4 Sq mtr each all as specified and directed

Taking down Shutter of any description exceeding. 1 sqm and not exceeding 2 sqm each all as specified and directed.

Taking down Shutter not exceeding1 sqm each all as specified and directed.

Pressed steel frames of size 165 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed.

Pressed steel frames for doors with one or more rebates with necessary fixing lugs, hinges, lock strike plate, etc., complete, size of frame 105 x 60mm, all as specified and directed.

2nd class Hard wood 35 mm thick Glazed and skeleton shutters, open rebated prepared to receive glass/ gauze etc. edges of framing, divided in to squares with plain chamfered or rounded, fitted with cut, mitred beads for securing glass/ gauze all as specified and directed Note: Glazing and gauze will be measured and paid separately.

35mm thick factory made plain framed panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS 1003 Part-I kiln seasoned and chemically pressure treated all as specified and as directed

Factory made 30mm thick PVC moulded Panelled door shutter with 2 or 4 raised panel comprising of wooden frame and filler material with Pine / hard wood tubular board and Rigid PVC face with 0.50mm thick on both face of approved make all as specified and directed. Make: Durian or equivalent make approved by GE.

Solid PVC door frame of size 50 mm x 47 mm made out of 5mm plain color PVC sheet reinforced with MS Square tube, fixed in opening as per specification and drawing all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (stile) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site all as specified and directed.

Steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded with glazing bars all as specified and directed.

Side hung shutters including projecting type hinges with steel handle complete with out glazing bars dovetailed or welded as fly proof shutters for steel windows of item No 12 as above all as specified and directed.

Steel ventilator with top hung shutter including hinges, steel peg stay, fixed including welding complete all as specified and directed.

Mild steel framed work such as grill / guard bars including fixing on steel window frame all as specified and directed.

Plain cement concrete 1:3:6 Type C0 (using 12.50 mm graded stone aggregate) as in filling hollow of pressed steel frame all as specified and directed.

PCC 1:2:4, type B1, using 20mm graded stone aggregate as in bed block for fixing holdfasts and coping/ benching including necessary use and waste of form work complete all as specified and directed.

MS Butt hinges medium weight cold rolled 100mm long all as specified and directed.

Butt hinges extruded Aluminium alloy with galvanized mild steel hinge pin, anodized and fixed, type C-21, with MS hinge pin 100mm size all as specified and directed.

Aluminium anodized barrel tower bolt of extruded section 150mm length all as specified and directed.

Extruded aluminium alloy handles fabricated type 150 mm size, anodized all as specified and directed.

300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel pin fixed to door, over all length 140mm all as specified and directed.

Single action spring hinges, mild steel with steel wire spring, stove enamelled, black all as specified and directed.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to steel / wooden joinery all as specified and directed.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples as in repairs to steel / wooden Joinery all as specified and directed.

Ground or obscured or frosted on one side, sheet glass 4 mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in each pane all as specified and directed.

Plain Sheet glass 4.0mm thickness ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane all as specified and directed.

Plain Sheet glass 4.0mm thickness ordinary quality and glazing with oil putty in square but exceeding 0.5 sqm in each pane all as specified and directed.

Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers all as specified and directed.

Fancy type Steel PVC Coated, drapery rod of size 20-25mm dia, including fixing of Steel powder coated fancy brackets and end stops 2 Nos in each opening etc complete all as specified and directed.

Preparation of new wood surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

Preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

12mm thick prelaminated termite resistant water proofing plywood interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work, fixed in repairs all as specified and directed.

18mm thick prelaminated termite resistant water proofing plywood interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work, fixed in repairs all as specified and directed.

Anodised aluminium door shutter, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc., complete all as specified and directed.

Plain sheet glass 4.8mm thick ordinary quality and glazing with oil putty in square exceeding 0.5 Sq.m in each pane complete all as specified and directed.

Door closer aluminium (extruded section) body hydraulically regulated designation No.3 universal type suitable for door shutters of 851 to 1000 mm in width and weight between 61 to 80 kg and fixed complete all as specified and as directed.

Double action floor spring hydraulically regulated made up of minium 1.25mm thick alluminium alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass other pars made up of mild steel heavy duty and fixed all as specified and directed.

Health faucet (Jet Spray ) Brass CP, 15mm dia with flexible pipe 1m long and fixing nut etc complete fixed in repairs all as specified and directed.

PVC valveless syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets of 10 litre capacity, fixed in repairs all as specified and directed.

Sinks with drainage board fixed in repairs made of stainless steel 1mm thick, kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm all as specified and directed.

chromium plated shower rose 100 to 125 mm size, with or without swivel joint, including fixing to 15mm dia steel pipe or union fixed in repairs all as specified and directed.

Vitreous china wash basin, white, flat back, size 550 x 400mm including cutting for and pinning in ends of brackets but exclusicve of fixing of and waste pipe complete fixed in repairs all as specified and directed.

Vitreous china wash basin, white, flat back, size 450 x 300mm excluding taps, waste, chain and plug and procelain stopper but including brackets, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe fixed in repairs all as specified and directed.

Vitreous china squatting pan, Orissa pattern of size 580 x 440mm (white coloured) with integral foot rests (excluding flushing cistern and flush pipe) with P or S trap portion to match with existing surface of floor and fixed in repairs all as specified and directed.

Vitreous China, wash down water closet pan (Pedestal pattern), white (excluding flushing cistern and flush pipe) complete fixed in repairs all as specified and directed.

Bib taps of cast copper alloy fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm bore, fixed in repairs all as specified and directed.

15mm dia bore bib tap standard of PTMT any colour, high pressure screwed for iron pipe (minimum weight 15mm-90gms / 20mm-125gms) and fixed in repairs all as specified and directed.

Pillar taps, fancy type, 15mm dia cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe all as specified and directed.

15mm dia bore Pillar taps of PTMT any colour, high pressure screwed for iron pipe (minimum weight 15mm-110gms) and fixed in repairs all as specified and directed.

Angle/ stop valve fancy type 15mm dia high pressure cast copper alloy chromium plated screwed down with crutch or butterfly handle, screwed both ends for iron pipe or for unions fixed in repairs complete all as specified and directed.

Angle/ stop valve fancy type 15mm dia for shower rose, fancy type cromium plated cast copper alloy, with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed in repairs all as specified and directed.

20mm dia Gunmetal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed in repairs all as specified and directed.

32/40mm dia expandable type PTMT waste pipe for wash hand basin/ kitchen sink complete all as specified and directed.

25mm dia Gunmetal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed in repairs all as specified and directed.

PVC connections 15mm size with PTMT nuts of length 450mm all as specified and directed.

15mm dia chromium plated cast copper alloy fancy type, two in one combination of bib tap and angle valve fixed in repairs all as specified and directed.

Taking up or down steel / PVC tubing and connections, bore of pipe upto 15 mm, all as specified and directed.

15mm bore unplasticised PVC pipes including fittings of pressure rating 10 Kgf/cm² laid and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Taking up or down steel / PVC tubing and connections, bore of pipe upto 20 mm, all as specified and directed.

20mm bore unplasticsed PVC pipes including fittings of pressure rating 10 Kgf/cm² laid and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Taking up or down steel / PVC tubing and connections, bore of pipe upto 40 mm, all as specified and directed.

40mm bore unplasticsed PVC pipes including fittings of pressure rating 10 Kgf/cm² laid and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Dismantling and removing water tanks of capacity exceeding 250 ltrs and not exceeding 500 ltrs all as specified and directed.

Dismantling and removing water tanks of capacity exceeding 500 ltrs and not exceeding 1000 ltrs all as specified and directed.

Rotational moulded polyethylene water storage tanks, ISI marked (cylindrical vertical with closed top) hoisted and fixed in position, 500 ltrs capacity all as specified and directed.

Rotational moulded polyethylene water storage tank, ISI marked (cylindrical vertical with closed top) of capacity 1000 ltrs hoisted and fixed in position all as specified and directed.

110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floor all as specified and directed.

PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed.

Dismantling of wall ceiling boards (fibre, pulp, insulation, etc) or insulation boards/ slabs/ blankets, any thickness, including cover fillets all as specified and directed.

False ceiling using GI snap grid system with roll-formed out of hot-dip galvanised steel capping (powder coated), main runner 38x24mm, cross Tee 29x24mm and wall angle 24x24mm and thickness not less than 1 mm, members suspended with Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long , with 4mm thick designer ceiling board of any texture (Lake & hill, Oceanic, cascade or Electra) as approved by GE, all as per Everest Ceiling grid system "Regular T-2430" or its equivalent make of "Ramco/ Charminar/ Armstrong" including demolition of wall and ceiling boards (fibre pulp, insulation, etc) or insulation boards/ slabs/ blankets, any thickness, including cover fillets all as specified and directed. Note: Suspenders of GI wire 4mm dia shall be provided at 1200mm centre to centre alongwith telescopic adjustable fastening system (nut & bolt) of minimum 6mm dia.

Demolition of Brickwork, stone / boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 mtr mean radius built in cement mortar (1:6) for all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc ,complete all as specified and as directed.

Rendering 15mm thick on fair face of brick wall / concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement all as specified and directed.

Preparation of newly plastered surfaces of walls and applying three coats of white wash all as specified and directed.

Applying two coats of oil bound distemper on surfaces of walls over two coat of 3 mm thick wall care putty including removal of existing treatment and a coat of priming paint on old wall surfaces all as specified and directed.

Demolition of Concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding all as specified and directed.

Sunken floor treatment by providing injection pressure grouting treatment using cement slurry mixed with grout admixtures non shrink additive using 40PSI pump complete and applying two coats of brush bond acrylic polymer modified cement based coating thickness 1mm or two coats of pidifin 2K acrylic polymer water proof coating including necessary surface preparation, providing 20mm thick water proofing scred bed / plaster in cement mortar 1:4 mixed with conplast x 421C @ 100ml or pidiproof LW @ 200ml per bag cement. Two coat of Nitro proof 100 bitumen based water proofing over plastered surface complete all as specification of chemical resistant coating complete all as specified and directed. Note: The work shall be executed through authorised applicator of M/s FOSROC/ pidilite using the materials supplied by M/s Fosroc chemicals India Pvt Ltd or M/s Pidilite Industrial Ltd and in accordance with their respective maufacturers instructions.

400mm thick lime concrete with lime mortar 1:3 mix and 40mm graded brick coarse aggregate in sub floor all as specified and directed.

Screed bed or bedding layer 15mm thick for laying floor finishes in cement mortar 1:6 all as specified and directed.

Non-skid white coloured ceramic tiles 7 to 8mm thick, (square/ rectangular) area of each tile exceeding 0.06 Sqm and not exceeding 0.11 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

White glazed ceramic tiles 300 x 200 x 6-7mm thick as in skirting / dado set and jointed in neat cement slurry and pointed in coloured cement to match colour of the tile complete all as specified and directed.

25mm thick plain cement concrete type B0 1:2:4 using 12.5mm graded stone aggregate as in sub floor, sub bases, floors and pavings etc complete all as specified and directed.

Rendering 10mm thick in cement mortar 1:4 on fair faces of brick/ stone wall or concrete surfaces as backing coat all as specified and directed.

Cast iron floor trap size 75 mm dia with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as specified and directed.

Cast iron nahani trap 75 mm dia with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as specified and directed.

SARASWATHI CONSTRUCTION

p.chinnasamy

UNIQUE INDIA CONSTRUCTIONS