REPAIR AND MAINT TO WALL PANELING SOUND PROOFING CEILING JOINERIES FLOOR AND WALL TILING ETC AND OTHER CONNECTED B/R WKS IN TECH AREA OF ARMY AVN SQN UNDER AGE (I) CIF (K)

Amount

Demolition of cement concrete in ground floor and paving n. exc 15 cm thick (below or above ground level) complete all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (not backing) removing serviceable tiles to store and rubbish of the premises complete all as specified and directed.

Taking down cement plastering on stone wall/ brick wall etc including racking out of joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L 15mm thick rendering on fair faces of brick or concrete surfaces in CM 1:6 and finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L 15mm thick rendering on fair faces of brick or concrete surfaces in CM 1:4 and finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L non skid ceramic coloured tiles not less than 8mm thick 1st quality (square/ rectangular) area of each exc 0.06sqm but n exc 0.11 sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface and over and including screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6 complete all as specified and directed.

M&L coloured glazed ceramic tiles of size (350x250x7mm/ 450x350x7mm) thick on vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 10mm thick cement plaster in CM 1:4 complete all as specified and directed.

M&L vitrified ceramic tiles light shade/ double charged/ ultracharged 10mm thick (square/ rectangle) polished area of each tiles exc 0.42sqm but n. exc 1.0sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 for laying floor finishes complete all as specified and directed.

M&L vitrified ceramic tiles light shade/ double charged/ ultracharged 10mm thick (square/ rectangle) polished area of each tiles exc 0.42sqm but n. exc 1.0sqm in skirting etc set and jointed in neat cement slurry and pionted in white or coloured cement to match over 10mm thick cement plaster in CM 1:4 complete all as specified and directed

M&L 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in levelling course of flooring complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection/ path finishing the surface even and smooth without using extra cement complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and directed.

M&L 25mm outer dia 3-layer PP-R (ploypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stablised and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and directed.

Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of shelves, for water tubing etc and making good, cutting exc 10cm girth but n exc 20cm girth in stone walls complete all as specified and directed.

S&F in repairs vitreous china wash hand basin (550x400mm) white, flat back excluding taps, including brackets & 32mm waste coupling complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedastal pattern) " with plastic water closet seat cover closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F in repairs 10 litres PVC valveless syphonic action type flushing cistern low level white with inlet ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32mm dis for low level cistern complete all as specified and directed.

S&F in repairs 15mm dia bib taps cast copper alloy fancy type chromium plated with crutch or butterfly handle screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs 15mm dia fancy type pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe fixed complete all as specified and directed.

S&F in repairs 15mm dia stop vlaves/ angle valve chromium plated, fancy type with long shank and cup screwed down, high pressrue with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and directed.

S&F 15mm PVC connection 450mm long with PTMT nuts for superior quality complete all as specified and directed.

S&F health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 mtr long flexible tube and ABS wall hook including making connection and fixed in position complete all as specified and directed.

Dismantling of boarding, ceiling, wall panelling any description, fixed in any position complete all as specified and directed.

S&F high density WPC (wood plastic composite) louvers panel as in ceiling 25mm thick of any length and width fixed on ceiling including fixing of L corner, ceiling rod fixed with hold fastner, ceiling keel for gird, ceiling slat or any other accessories complete all as specified and directed. The specification of material is as under :- (a) The length of WPC panel should have in a single piece and width tie between 203mm to 150mm. (b) Looks and feels like natural wood. (c) 100% non-toxic, non formaldehyde, environmental friendly. (d) Water proof; termite proof. (e) No cracking, anti impact with high density. (f) Anti-UV, good colour fastness. (g) No glue, no need to paint and can be painted. (h) Easy installation and low maintenance. (j) Water resistant. (k) Flame retardant. (l) Colour and make will be as approved by AGE (I).

S&F high density WPC (wood plastic composite) louvers panel as in wall paneling 25mm thick of any length and width fixed on wall surface including fixing of L corner, buckle with slef tapping screws or any other accessories complete all as specified and directed. The specification of material is as under :- (a) The length of WPC panel should have in a single piece and width tie between 203mm to 150mm. (b) Looks and feels like natural wood. (c) 100% non-toxic, non formaldehyde, environmental friendly. (d) Water proof; termite proof. (e) No cracking, anti impact with high density. (f) Anti-UV, good colour fastness. (g) No glue, no need to paint and can be painted. (h) Easy installation and low maintenance. (j) Water resistant. (k) Flame retardant. (l) Colour and make will be as approved by AGE (I).

M&L picking the existing epoxy floor and grinding mechanically to make floor level & cleaning with solvent based cleanser of pidilite or equivalent, applying with mop or brush, cleaning the surface with water after drying etc., and applying the epoxy resin on floor of overall thickness 5mm including 1mm thick top coat (top coat colour as decided by AGE (I). The material will be handled, stored, and applied strictly by authorised applicator only as per manufacturer's direction complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frame) of any description alongwith fittings n. exc 1.5sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frame) of any description alongwith fittings n. exc 1.5sqm n. exc 4sqm each complete all as specified and directed.

S&F anodised aluminium frame (powder coated minimum thickness of powder coating 50 micron) for doors, windows, partition wall with one or more rebates including joining cleat for fixing, rubber packing, anodised aluminium snap on beading for fixing glass panes in frame etc complete all as specified and directed.

S&F anodised aluminium (powder coated minimum thickness of powder coating 50 micron) for door shutter, aluminium section weighing 0.55 Kg/ sqm including necessary joining, cleats, glazing clips, rubber neoprene packing, handles 2 nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and directed

S&F anodised aluminium (power coated minimum thickness of powder coating 50 micron) sliding window, ventilator shutters without sash bar, aluminium section weighing 0.55 Kg/ sqm including necessary joining cleats, glazing, clips, rubber packing, anodised aluminium snap, beading, screws etc, complete all as specified and directed.

S&F brass mortice lock vertical type 100mm size 4 lever complete all as specified and directed.

M&L 12mm thick prelaminated particle board, interior grade, prelaminated on both side with decorative choice lamination and fixed with screws to aluminium frame work complete all as specified and directed.

S&F door closer hydraulically regulated of cast iron body designation No 2, universal type, suitable for door shutters of 701 to 850mm in width and weight between 36 to 60 Kg and fixed complete all as specified and directed.

S&F 10mm thick toughened glass as in hinged door, partition automatic doors and similar work including cutting shape, drilling holes, grinding/ polishing and rounding off edges of glass, including providing and fixing door handle, hinges, hydraulic foundation of ISI marked, logo/ hallmark and other fixing arrangement etc complete all as specified and directed.

M&L preparation of new plastered surfaces on walls and applying two coats of oil bound distemper over primer and 3mm thick wall care putty complete all as specified and directed.

M&L preparing old plastered or unplastered surfaces of walls for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/ litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @0.90 litre/ 10sqm over surfaces complete all as specified and directed.

Notes :- An amount of Rs. 16,400.00 on account of Credit Schedule for Schedule 'A' Part-II shall be deducted from total quoted amount of BOQ to arrive at the contract sum.

M/S SHIMAR STAR GLACIER (BID ID -3391845)

M/S M.S TANVEER ENTERPRISES (BID ID -3390578)