REPAIR REPLACEMENT EXISTING SEWERAGE PIPE LINES INCLUDING SEPTIC TANK MANHOLES, SOAKAGE WELL, VIFT TRAVERSE WALL AND OTHER CERTAIN MISC WORKS AT ZONE A AND REPAIR TO FOOTPATH, FENCING, HARDSTANDING, DRAIN AT MIL STN KANASAR UNDER GE (N) BIKANER

Amount

Demolition of cement concrete(un-reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L plain cement concrete type D2, 1:4:8, 75 mm thick in sub base of floor finished even and rough to receive top layer complete all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed.

Dismantling fencing wire mesh, any type complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and as directed.

M&L for cement concrete type B1, 1:2:4 (20 mm graded stone aggregate) for fixing of MS angle, columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified & directed.

Supply & Fixing in repair galvanized 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossing with and provision of galvanized mild steel wire, staples or steel pins including taking down of old barbed wire etc complete all as specified & as directed. Note:- Each line of horizontal / vertical / diagonal wire to be measured for the purpose of payment.

M & L for restraining, resecuring including securing tying at crossings of galvanised mild steel and old galvanosed barbed wire to any type of standard rails complete all as specified & as directed.

S & F of MS Angle for posts and struts in fencing including cutting tops to shape as directed, drilling holes, matching for wire etc, flat iron (for securing wire mesh etc) including all necessary drilling, bolting or reveting etc an similar work confirming to Fe-290 Gde E-165 complete all as specified and directed.

Supply of chain link MS galvanised fencing, any size of type complete all as specified & as directed.

Fixing only chain link fencing including line wires any mesh, size and type to any type of standards, rails, straining bolts etc. including provision of binding wire complete all as specified and directed. Note:- Supply only chain link fencing shall be measured and paid for separately.

S&F for 10mm dia MS round bar for fixing of chain link fencing with posts complete all as specified & as directed.

S&F of Mild steel screw bolts (machine made) of dia of neck 5-10mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n exc 10 cm long complete all as specified and directed

M & L for preperation of new steel surfaces over 10cm in width or girth not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specifed and as directed.

M&L for preperation of new steel surfaces n.exc 10cm in width or girth when unconnected with other painting and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specifed and as directed.

Surface dressing not exceeding 15 cm deep including clearing away all grass vegetation, saplings, shrubs, brushwood, undergrowth, roots, and trees not exceeding 30 cm girth (measured one metre above ground level) and removing rubbish upto a distance of 50 metres outside the periphery of the area under clearance and getting out in soft/loose soil.

Supply & stacking of Moorum/Red Bajri at base/ground level near shead or any other places in depot area for filling purpose under item No. 3.00 to 7.00 complete all as specified & as directed. Note :- (i) Payment of Moorum/Red Bajri shall be made to contractor after verifying the quantities by a BOO. (ii) BOO shall be convened by GE (N) Bikaner. (ii) Rate deemed to be included by contractor for digging of Moorum/Red Bajri, bringing to site of work from outside Defence Land.

M&L for forming embankments including raising (or lowering) earth, spreading in layers not exc. 30 cm thick, watering, ramming/rolling and finishing to required size, shape, etc., not exc. 1.5 m high from base complete all as specified & as directed. Note :- (i) Rate deemed to be included for suitable water supply arrangement upto 1.50 Mtr height from ground level for well waterring/ ramming purpose. (ii) Rate deemed to be included by contractor for digging of Moorum/Red Bajri available at base /ground level and carriage to place of deposition.

M&L for forming embankments including raising (or lowering) earth, spreading in layers not exc. 30 cm thick, watering, ramming/rolling and finishing to required size, shape, etc., exc. 1.5 m and n exc 3.0 m high from base complete all as specified & as directed. Note :- (i) Rate deemed to be included for suitable water supply arrangement upto 3.00 Mtr height from ground level for well waterring/ ramming purpose. (ii) Rate deemed to be included by contractor for digging of Moorum/Red Bajri available at base /ground level and carriage to place of deposition.

M&L for forming embankments including raising (or lowering) earth, spreading in layers not exc. 30 cm thick, watering, ramming/rolling and finishing to required size, shape, etc., exc. 3.0 m and n exc 4.5 m high from base complete all as specified & as directed. Note :- (i) Rate deemed to be included for suitable water supply arrengement upto 4.50 Mtr height from ground level for well waterring/ ramming purpose. (ii) Rate deemed to be included by contractor for digging of Moorum/Red Bajri available at base /ground level and carriage to place of deposition.

M&L for forming embankments including raising (or lowering) earth, spreading in layers not exc. 30 cm thick, watering, ramming/rolling and finishing to required size, shape, etc., exc. 4.5 m and n exc 6.0 m high from base complete all as specified & as directed. Note :- (i) Rate deemed to be included for suitable water supply arrangement upto 6.00 Mtr height from ground level for well waterring/ ramming purpose. (ii) Rate deemed to be included by contractor for digging of Moorum/Red Bajri available at base /ground level and carriage to place of deposition.

M&L for forming embankments including raising (or lowering) earth, spreading in layers not exc. 30 cm thick, watering, ramming/rolling and finishing to required size, shape, etc., exc. 6.0 m and n exc 7.5 m high from base complete all as specified & as directed. Note :- (i) Rate deemed to be included for suitable water supply arrangement upto 7.50 Mtr height from ground level for well waterring/ ramming purpose. (ii) Rate deemed to be included by contractor for digging of Moorum/Red Bajri available at base /ground level and carriage to place of deposition.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

M&L for brick work with old size burnt clay sub-class ‘B’ bricks, curved to plan with mean radius not exc 6m with bricks roughly cut to radius or bricks with wedge shaped joints, built in cement mortar 1:4 complete all as specified and as directed.

Taking down cement plaster or cement lime plaster etc on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc, complete all as specified and as directed.

M&L for rendering 15 mm thick in CM 1:4 mixed with waterproofing compound as per manufacturer's instructions on brick masonary including finish even and smooth surfaces using without extra cement of walls & floors, complete all as specified and as directed. Note : Water proofing compound shall be measured and paid separately.

M&L for preparation of newly plastered surfaces & applying two coats of cement base paint over a coat of alkali resistant priming paint on walls complete all as specified and as directed.

Supply only Liquid water proofing compound.

S&F in repairs for 0.56 mm thick Plain, Aluminium sheeting, Alloy 31000 H4 in covering of crumple joints and straight flashing (length and girth as fixed) including dismantling of plain or corrugated steel sheeting (Roof covering) of any description or any gauge or thickness complete all as specified and as directed.

Cleaning and functioning of existing sewage system ( comprising of sewer lines in PVC, CI, SGSW or RCC precast pipes), house connection from WC, bath, kitchen sink, wash basin etc including gully traps, floor/Nanhi trapes, CI pipes and plumbing works etc of any posistions below or above ground level, located in different situations and also on the surface of the wall etc upto 1st manholes complete in perfect functioning/ removing connections without obstruction by removinng all blockage in system including removing of all waste, solid or liquid or of any description by rodding, by pressure pumps of any description or by other mechanical equipments, all as s specified and directed . Note for Item No 31 :-The contractor/his rep will collect the complaint from complaint cell every day at 9.00 AM and rectify the complaints same day and deposit the complaint slip ( duly signed by the users ) to concerned JE. If the contractor fails to rectify the defects mentioned in the complaint (Job) on same day, he will be charged Rs. 500/- per Job/per day and same will be recovered from his RAR.

Desludging by removing of solid/semi solid sludge, silt, foul water from the existing manhole of depth not exceeding 1.0 mtr, any capacity, in foul conditions, either by manually or by mechanically and flushing water to ensure free flow of sewage , placing in position the manhole coverrs of any decription, removal of sludge & solid contents to any place outside defence land complete all as specified and as directed.

Ditto all as per item No.32 here-in-before but depth exceeding 1.00 mtr but not exceeding 1.50 mtr.

Ditto all as per item No. 32 here-in-before but depth exceeding 1.50 mtr but not exceeding 2.00 mtr.

Desludging by removing of solid/semi solid sludge from the existing septic tank of any depth, of capacity 25 users ,in foul conditions, including taking & placing in position the manhole covers of any description, removal of complete sludge & solid contents by mechanical means to any place outside defence land and depositioning where directed by Engineer-in-charge.

Ditto all as per item No.35 here-in-before but 50 users.

Ditto all as per item No.35 here-in-before but 150 users.

Cleaning of existing sewer pipe/liness of any dia and at any depth (internally from manholes at any depth by rodding manually/ mechanically or with de-sludging machines as required at site including the following : (a) Getting out the solid sludge and liquid matters from the connecting manholes. (b) Removing sludge land depositing and spreding at safe place far from populated area as directed by the Engineer-in-Charg. (c) Removing and replacing in original position of manhole covers of any description complete.

De-watering the existing soak wells/pits/septic tanks and disposal of the same to the surrounding low lying area nearly all as specified and directed.

Demolition and breaking up drain pipes ( SGSW,AC, PVC or RCC) of internal dia of 150mm, set in cement mortar complete all as specified and directed.

Excavation in trenches, n.exc 1.5M wide and not exceeding 1.5M in depth; for foundation etc or for shaft, wells, cesspits, manhole, pier holes etc n.exc 10 Sqm on plan and n.exc 1.5M in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm depth in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Removing excavated surplus soil material to distance not exc 50M and depositing where directed at a level n.exc 1.5M above the starting point complete all as specified and directed

Supply and fix 150mm dia reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and as directed. (concrete bed shall be measured and paid for separately. )

M&L for PCC 1:3:6, type C-2, using 40mm graded stone aggregate as in bed of RCC NP3 pipe 150mm bore including packing under and hunching against the sides of pipes after they are laid and tested complete all as specified and directed

Demolition of reinforced cement concrete cover slab for MH/Septic tank and removing the debris to a distance not exc 500 M as directed.

Material and labour for pre cast reinforced cement concrete manhole cover 1:1.5:3, type A1, (Using 20mm graded stone aggregate) set in CM 1:4 complete including necessary formwork all as specified and as directed.

M&L Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete.

M&L for cement concrete type B-1,1:2:4 using 20mm graded stone aggregate crushed stone aggreate as in copings, kneelers, apex stones, bed plates and the like including weathering, slightely rounded, chamfered angle and throating as directed including use and waste of form work (straight & curved) all exposed surfaces of concrete finished fair complete all as specified and directed.

M&L Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex-tra cement, including forms, moulds, mi-tred/stopped ends etc.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation/mass concrete etc complete all as specified and directed.

Demolition of stone slabs as in roofs, suspended floors any thickness jointed in any mortar complete all as specified and directed.

M&L for Jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6 complete complete all as specified and directed.

M&L for 40 mm thick PCC (1:2:4) type B-1using 20mm graded stone aggregate, as in floors or over stone patti roof slab, finished the surfaces even and smooth eithout using extra cement complete all as specified and directed.

Dismantling floor hearth and wall tiles including cement mortar bedding (but not backing) and removing from site complete all as specified and directed.

M&L Non skid coloured ceramic tiles area exc 0.06 sqm but not exc 0.11 sqm 7 to 8 mm thick as in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15 mm thick screed bed in cement and sand mortar 1:4, complete all as specified and as directed by Engineer-in-Charge.

S & F in repair PVC (SWR) multi floor trap /floor trap plain with PTMT garting including jointing with solvet cement, dia of outlet 100mm, complete all as specified and directed.

S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint / solvet cement joint laid in trenches or in floors complete all as specified and directed including dismantling and taking out old ounserviceable any type of pipe with fittings complete all as specified and directed.

S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint / solvet cement joint fixed to wall complete all as specified and directed including dismantling and taking out old ounserviceable any type of pipe with fittings complete all as specified and directed.

S & F 110 mm bore PVC (SWR)bend, in repair any radius with oval access door complete all as specified and directed.

S & F 110 mm bore PVC (SWR) single junction (single'T') in repair equal or unequal provided with access door complete all as specified and directed.

S & F as in repairs Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) /CP complete all as specified and directed.

S & F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580 x 440 mm with integral foot, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc, complete all as specified and directed.

S &F in repairs PVC valveless symphonic action type low level flushing cistem ( ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed.

S & F in repairs vitreous china below counter wash hand basin (self rimming) white oval type of size 550 x 445 x 190 mm fixed in granite flatform & including 32 mm dia PVC waste pipe and 32 mm dia chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end complete all as specified and directed.

S & F in repair PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTM T nuts on both side complete all as specified and directed.

S&F in repair Wash down water closet (Pedestal pattern), complete with PVC (SWR) 'P' trap 110mm dia including jointing with cement mortar to existing CI pipe line complete all as specified and as directed by Engineer- in - Charge.

S & F in repairs plastic water closet seat, white, closed pattern with flat botttom and cover and mild steel chromium plated or aliminized hinging device, complete all as specified and directed.

S & F in repair 32 mm bore Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connectiions including necessary packing, union and cap and fiexd including taking down, complete all as specified and directed.

S & F in repairs 15 mm bore chromium plated fancy type bib taps, cast copper alloy, with crutch or butterfly handle, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S &F in repairs 15 mm bore pillar tap, cast copper alloy with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold with long screwed shanks & fly nuts, screwed for iron pipes complete all as specified and directed.

S & F in repairs 15 mm bore fancy type chromium plated stop vavle/angle valve, cast copper alloy, screwed down, high pressurenwith crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in repairs 15 mm bore fancy type Brass CP basin mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks exc 250 litres & not exc 500 litres capacity and from mouhts of circulating pipes, etc.

Cleaning and removing all scale and dirt, etc, from tanks exc 500 litres & not exc 1000 litres capacity and from mouhts of circulating pipes, etc.

S&F in repairs of Ball valves size 20 mm high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified and as directed.

SHREE GURU NANAK CONSTRUCTION COMPANY (BID ID -3442752)

M S GROUP (BID ID -3445261)

vikas builders (BID ID -3446022)