CA NO CWE BTD 12 of 2020-21 SPECIAL REPAIRS TO BLDG NO OP- 72/1 TO OP- 72/4 AT OLD NILGIRI ENCLAVE UNDER GE (SOUTH) BATHINDA AT BATHINDA MIL STN

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area not exc 1.5 Sqm each and removing from site including cutting holes for removal of hold fast complete.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified in Preamble 8B.3.1 of SSR Part -II (2010) and all as shown on drawing of SSR Part-II (2010).

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement all as per instruction and drawing shown for item No 8080 of SSR Part II.

S & F 200 mm long aluminium anodised, barrel tower bolts of extruded section.

S & F 125mm extruded aluminium alloy handles, cast type, anodised.

S&F 100mm long size Hasp and staple, safety type, aluminium anodised with hinge pin including bolt to hinge plate and fixed with screws.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type), and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, length of bolt 250mm.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4 Sqm each and removing from site including cutting holes for removal of hold fast complete.

S&F factory made pressed steel frames for door with one or more rebates including necessary fixing lugs, lock strike plate, hinges etc, compete, all as specified of frame size 105 mm x 60mm & thickness of MS sheet shall not be less than 1.25 mm including making holes for fixing hold fast etc and making good the wall with plaster in cement mortar (1:6) complete.

S&F factory made pressed steel frames for door with one or more rebates including necessary fixing lugs, lock strike plate, hinges etc, complete, all as specified of frame size 125 mm x 60mm & thickness of MS sheet shall not be less than 1.25 mm including making holes for fixing hold fast etc and making good the wall with plaster in cement mortar (1:6) complete.

S&F factory made pressed steel frames for cupboard frames with one or more rebates including necessary fixing lugs, lock strike plate, hinges etc, complete, all as specified of frame size 75 mm x 60mm & thickness of MS sheet shall not be less than 1.25 mm including making holes for fixing hold fast etc and making good the wall with plaster in cement mortar (1:6) complete.

M & L for PCC (1:3:6) type C-0 using 12.5 mm graded stone aggregate in filling in chowkats/ door frame or bed block of hold fast and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each and removal from site.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each and refixing in the same opening including easing and adjusting and including renewal of unserviceable screws etc complete.

S&F 35mm thick factory made panelled shutter (two panel) plain framed with lock rail and panel of 12mm thick veneered particle board with commercial veneering on both faces conforming to IS-3097 exterior grade kiln seasoned and chemically pressure treated of second class hard wood rails and styles and the size of rail and style as per IS-1003 (Part I).

S&F factory made glazed and skeleton shutters 35mm thick using second class hard wood open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc; sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24(a); all as specified complete.

S&F aluminium alloy powder coated window sliding type (three track) with frame size 100mm x 35 mm x 1.2 mm and shutter 39.40 mm x 17.70 mm x 1.20 mm thick, with two glass shutter and one stainless steel mesh shutter including 5.5 mm thick tinted glass including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws, 0.56 mm dia SS wire mesh, all fittings complete.

S&F factory made powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 nos.) suitable handle (1 no.) complete all as specified. (minimum thickness of power coating shall be 50 micron)

S & F butt hinges, medium weight, cold rolled mild steel and fixed, size of hinges 100mm.

S&F in repairs, 1.00 mm thick mild steel, plain, black sheet as in covering to doors, water tank, water trough etc, cut to size edges beaded if directed, holes punched, including round headed screws, clout nails or riveting and welding etc as required complete all as directed.

S&F Rubber gasket 50mm wide fixed with screws or nail etc at bottom of door shutters of any description, complete all as specified.

S & F in repairs, magic eye for flush/ panelled door shutter etc complete all as specified.

S & F 100 mm Double action spring hinges, mild steel with steel wire spring, stove enamelled, black complete.

M&L Welding in repairs, not exc. 6mm thick metal and not exc 2.50cm in length complete.

S & F 300 mm long MS ordinary rat tail rod pattern springs for doors including roller and roller plate complete.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire & average width of aperture 1.40mm and fixed with stainless steel wire staples complete.

S&F in repairs, stainless steel wire cloth, 0.36 mm nominal dia of wire & average width of aperture 1.40mm and fixed with stainless steel wire staples complete.

M&L for 6mm thick plywood, ISI marked, conforming to relevant IS, grade BWR, type BB, 5 ply, fixed with screws to timber frame work.

M&L for Decorative laminate type 1 of surface finish 0.90 mm thick, any colour and pattern as approved, fixed with approved adhesive as per manufacturer's instruction complete.

M&L for Decorative laminate type 1 of surface finish 0.75 mm thick, white colour and pattern as approved, fixed with approved adhesive as per manufacturer's instruction complete.

M & L for prelaminated particle board, 18/19 mm thick, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, ISI marked, fixed with screws to timber frame work complete including dismantling boarding of any type and description fixed in any position with rails including fillets complete.

S&F factory made PVC wall lining consisting of 5 mm thick plain colour PVC sheet having density not less than 600 kg/cum inclusive of solvent cement and fixing in position on back side of cup boards and like complete all as per specifications and drawings in SSR Part -II (2104).

M & L for second class hard wood plain fillets, square, rectangular or triangular in section, clean sawn of cross sectional area exceeding 3 Sqcm and not exceeding 6 Sqcm secured with nails or beads complete.

S&F Catcher such as in cupboard etc to catch and support shutters of best quality complete all as specified.

S & F in repairs floor door stopper of aluminium alloy body, and tongue, ISI marked, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm.

S & F in repairs Stainless steel telescopic channels for drawers of kitchen cup boards of any lenghth complete all as specified.

S & F fancy type, 100 mm stainless steel handles, for cup boards shutter complete all as specified.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised of 30 mm width of flap (when open).

S & F MS framed work such as grills, gratings, guard bars etc., with end of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 290 Gde E-165.

Drilling holes of suitable size for passing tubes of any description into or through RCC cooking platform slab with stone or brick wall etc and the like of thickness not more than 250mm by electric drilling machine and making good dismantled portion in cement mortar (1:3) or cement concrete (1:2:4) type B1 as required at site all as directed.

Cutting holes into or through brick walls, superficial area not exceeding 150 Sqcm, built in mud mortar and making good in cement mortar (1:3) or cement concrete (1:2:4) type B1 as required.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing or concealed conduit wiring, etc, and making good, cutting not exceeding 10cm girth in brick walls.

Cutting openings, through brick wall built in cement mortar or cement lime mortar for door, window and other openings or enlarging existing openings, converting window into door openings, etc or cutting out defective brick work for under-pinning including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard core, etc, to store and rubbish not exceeding 50m.

Forming jambs, etc., to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work in cement mortar (1:6), complete.

S & F MS framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc shall be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as directed conforming to Fe 410-W, Gde E-250 quality B.

S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins / spring clips size not exceeding 1.5 Sqm each pane complete.

S & F sheet glass, 4 mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane fixed with oil putty or wooden beads including Provn of glazing pins/spring clips wherever necessary complete.

S & F 4 mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete.

M & L for painting to new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces.

M & L for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces.

S&F in repairs 25mm dia drapery rod, stainless steel, chromium plated with fixing brackets, stops, rollers etc as in curtain rails. (Note : The cost of brackets and knobs is deemed to be including in the quoted unit rate. Nothing extra shall be paid on this account.)

Supply only liquid water proofing material, ISI marked.

M & L for PCC (1:2:4) type B1 using 20mm graded stone aggregate in coping, window cills, steps, bed blocks, roof kerbs or mud stops, rounded or chamfered on edges complete.

M&L for PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate mixed with liquid water proofing material as in benching, kerbs, mud stops, along side walls adjoining to roofs and similar items complete. (Water proofing material shall be measured and paid for separately).

M&L for PCC (1:5:10) type E2 using 40 mm graded stone aggregate as in filling of sunken floor including demolition of existing PCC.

Demolition of PCC (unreinforced) of any description and in any position not otherwise specifically provided and removing the debris upto a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.

Demolition of brick tiles or terracing tiles, single layer on roofs including removing the demolished material exceeding 1 km and not exceeding 2 km away from site and disposal off in low lying area as directed.

Demolition of mud in roof, any thickness including plastering and leaping (where full thickness recovered or only a part there of) including removing the demolished material not exceeding 200 m away from site and disposal off in low lying area complete.

M&L for sunken treatment to sunken floor, cleaning the surface by using wire brush, rendering to floor and sides with 10 mm thick cement mortar (1:3) including mixing of liquid water proofing material @ 200ml per bag of cement, finished even and smooth without using extra cement after that material & labour for providing two coats of two components (one part liquid two parts powder) ready to use cementations water proofing coating on properly prepared surfaces by brushing having elongation of >50% for the applying water proofing treatment as per following on horizontal and vertical surfaces of sunken floor complete all as per manufacturers instruction. (i) Applying 1st coat of two components modified polymer coating. (ii) Provn of glass fiber mess of 2 x 2mm immediately on alone coating. (iii) Apply 2nd coat of two components modified polymer coating after 72 hrs on horizontal and vertical surfaces.

Notes for Srl Item No. 60 : (i) Complete treatment shall be carried out by authorised applicator of waterproofing manufacturer as given in Appx 'B'. (ii) Water proofing material for mixing in cement mortar shall be measured and paid separately.

M&L for water proofing treatment over RCC slab by applying oil bound bituminous primer @ 0.30 kg/Sqm and providing and laying 3 mm thick APP modified water proofing memberane weighing not less than 3.50 kg/sqm, reinforced with non woven polyester reinforcement matt weighing not less than 160 gm/Sqm polyester core, having soften point not less than 150°C, longitudinal tensile strength not less than 650 N/ 5 cm, tearing strength of 180 N, torch application, side overlap 75 mm and end overlap 100 mm and tucked into the chases including ponding test all as specified and directed.

Taking down complete roof treatment of any description, thickness or any number of layers and M&L for wire brushing and cleaning top surfaces of roof slabs etc, including washing the roof surface with water and making the surface free from mud etc complete all as specified.

M&L for 15 mm thick screed bed or bedding layer in cement mortar (1:3) on roof surfaces parapet or vertical beam surface (horizental or vertical) finishing the surfaces even and fair complete all as specified. (Note :- Course sand (Toka sand) shall only be used in screed bed/plastering.)

M&L for Lime concrete in lime mortar (1:2) using 40 mm graded brick aggregate, laid to slope as directed by Engineer in charge over RCC roofs as padding complete alll as specified. Note: Minimum thickness of lime concrete at lower end shall not be less than 50mm.

M&L for 20- 22 mm thick factory made PCC tiles of size 250mm x 250mm with grey cement and no pigment , bedded in cement mortar (1:4) 15 mm thick and joints grouted flush in CM (1:3) mixed with @ 5% of crude oil by weight of cement complete all as specified.

S&F in repairs vitreous china wash down water closet pan (EWC) (single piece), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe etc and including flushing cistern and white coloured plastic seat cover and mild steel chromium plated or aluminised hinging device complete.

S&F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580mm x 440mm, white, with integral foot rests including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. including making good to floor and excluding flushing cistern, flush pipe and waste pipe.

S & F in repairs health faucet brass body with wall hook and 1 metre SS pipe complete all as per Cera Cat part No. F8030301 or equivalent model of approved make from list of make attached in tender documents.

S & F in repairs PVC valveless, syphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets and PVC flushing pipe 32mm dia complete.

S&F in repairs vitreous china pedestal type wash basin, white, flat back complete all as per Cera Cat part No. S2040113 for wash basin and S2090106 for pedestal or equivalent model of approved make from list of make attached in tender documents excluding waste, chain and plug and porcelain stopper but including waste coupling and PVC waste pipe of 32 mm dia and fixed on existing brackets complete .

M&L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar (1:3).

S & F in repairs, PVC connections 15 mm bore, 450 mm length, heavy duty, with PTMT nuts.

S&F in repairs brass chromium plated shower rose 125 mm size with or without swivel joints fix to steel pipe or union complete all as specified and as directed. Make:- Jaquar Cat part No. OHS-1789 or equivalent model of approved make from list of make attached in tender documents.

S&F in repairs angle valves, chromium plated, fancy type, quarter turn, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe.

S&F stop valves, cast copper alloy, fancy type, quarter turn, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe.

S&F in repairs, 15 mm bore chromium plated, fancy type, quarter turn, bib taps cast copper alloy with crutch or butterfly handle, screwed for iron pipe, or for brass ferrule complete all as specified and as directed.

S&F in repairs brass CP mixer for mixing hot and cold water screwed for iron pipe of 15 mm bore all as per Cera Cat part No. F2004405 or equivalent model of approved make from list of make attached in tender documents.

S&F in repairs brass CP single lever sink mixer wall mounted all as per Cera Cat part No. F2004501 or equivalent model of approved make from list of make attached in tender documents for mixing hot and cold water screwed down for iron pipe of 15 mm bore.

S&F in repairs, brass chromium plated tubular towel rail, 20 mm dia, D type, 600 mm long between flanges fixed with CP screws and wooden cleats. Make:- Jaquar Cat part No. AQN-7711 or equivalent model of approved make from list of make attached in tender documents.

S&F in repairs, chromium plated Soap dish complete. Make:- Jaquar Cat part No. AQN-7731 or equivalent model of approved make from list of make attached in tender documents.

S&F in repairs, chromium plated towel ring complete. Make:- Jaquar Cat part No. AQN-7721 or equivalent model of approved make from list of make attached in tender documents.

S & F PTMT Mirror cabinet of size 350 x 450mm best quality confirming to samples kept in GE's office, complete all as specified and direct.

S & F in repairs, fancy type corner glass shelf (300mm) with CP brass bracket and SS/ CP brass railing etc complete all as per Cera Cat part No. F5005103 or equivalent model of approved make from list of make attached in tender documents.

S & F in repairs, fancy type stainless steel recessed type toilet paper holder complete all as specified and direct. Make:- Jaquar Cat part No. AQN-7753 or equivalent model of approved make from list of make attached in tender documents.

S & F in repairs, peg set/ coat hooks (set of 4/ 5), stainless steel complete all as specified and direct.

S&F in repairs kitchen or laboratory sinks with drainage board made of stainless steel 1 mm thick fixed with plugs, washers; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete. Make:- Cera Cat part No.BYJ12101 matt finish or equivalent model of Jaquar/ Hindware/ Kohler.

S&F in repairs stainless steel plate rack made out of 1.00 mm thick sheet with chromium plated screws, rawl plugs of size 900 mm x 600 mmx 250mm complete all as specified.

Taking up or down old 15mm bore GI tubing including, cleaning for refixing and refixing same in new or old position in floor, wall or ceiling all as directed including provision of new fitting as per site requirement complete. Note:- The quoted rate is deemed to be including the cost of new fitting.

All as per item No. 89 above but 20mm bore.

All as per item No. 89 above but 25mm bore.

M & L for 15 mm bore GI pipe, medium grade, ISI marked, with all fittings and fixed complete to walls and ceilings or laid in floors including taking up or down 15 mm bore existing steel tubing and connections complete.

M & L for 20 mm bore GI pipe, medium grade, ISI marked, with all fittings and fixed complete to walls and ceilings or laid in floors including taking up or down 20mm bore existing steel tubing and connections complete.

M & L for 25 mm bore GI pipe, medium grade, ISI marked, with all fittings and fixed complete to walls and ceilings or laid in floors including taking up or down 20mm bore existing steel tubing and connections complete.

M & L for 40 mm bore GI pipe, medium grade, ISI marked, with all fittings and fixed complete to walls and ceilings or laid in floors including taking up or down 20mm bore existing steel tubing and connections complete.

M & L for 25 mm thick PCC (1:2:4) type B1 using 20mm graded stone aggregate as in floor finished even and fair.

M & L for double charged, light shade, vitrified ceramic tiles of size 600mm x 600mm, 9 to 10 mm thick (square / rectangular), polished, in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles. with including 15 mm thick Screed bed or bedding layer in CM (1:6) including dismantling existing floor/ floor tiling/roughening of old floors etc including cement mortar bedding and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified. Note: Only course sand shall be used in screed bed.

M & L for double charged, light shade, vitrified ceramic tiles, 9 to 10 mm thick (square / rectangular), polished, in vertical surfaces as in skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles. with including 10 mm thick rendering in cement mortar (1:4) as backing coat and finish the surface rough to receive the tile including dismantling existing hearth or wall tiling including cement mortar bedding (but not backing) etc on brick or stone walls etc including racking out joints hacking for key and scrubbing removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.

M&L for non skid coloured ceramic tiles of size minimum 400mm x 400mm, 7 to 8 mm thick (square/rectangular), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile with including 15 mm thick Screed bed or bedding layer in CM (1:6) including dismantling existing floor/ floor tiling including cement mortar bedding and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified. Note: Only course sand shall be used in screed bed.

M & L for light shade, vitrified paver tiles of size 300mm x 300mm, 9 to 10 mm thick (square / rectangular), polished, in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles. with including 15 mm thick Screed bed or bedding layer in CM (1:6) including dismantling existing floor/ floor tiling including cement mortar bedding and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified. Note: Only course sand shall be used in screed bed.

S&F glazed ceramic coloured tiles 450 x 350mm or 450 x 300mm, 7 to 8mm thick in verticle surfaces such as dado / skirting, set and jointed in neat cement slurry and pointed in white or coloured cement pigmented to the match the shade of tiles laid over and including 10 mm thick rendering in cement mortar (1:4) as backing coat and finish the surface rough to receive the tile including dismantling existing hearth or wall tiling including cement mortar bedding (but not backing) etc on brick or stone walls etc including racking out joints hacking for key and scrubbing removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.

M & L for precast cement concrete (1:2:4) type B0 using 12.5mm graded stone aggregate in lauvers and jallies, 35mm thick (measured solid), set in cement mortar (1:4) including all mouldings but excluding frame.

M&L for machine cut kota stone slab flooring minimum size 450 mm x 450 mm, 18 to 20 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing laid over and including 15 mm thick Screed bed or bedding layer in CM (1:6) complete.

All as per item No 103 above but in vertical surfaces such as skirting as directed at site including 10 mm thick rendering as backing coat in cement mortar (1:4) all as directed.

M&L for granite (of any type) work 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including dismantling of existing floor, hearth or wall tiling including cement mortar bedding (but not backing), terrazo dado/wall tiling and skirting. etc on brick or stone walls etc including racking out joints hacking for key and scrubbing removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.

M&L for Rounding of/ moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish) complete all a specified.

M&L for marble work (udaipur green) 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble and roundening to the edge of stone slabs on edges including M&L for 15 mm thick Screed bed or bedding layer in CM (1:6) including dismantling of existing floor, hearth or wall tiling including cement mortar bedding (but not backing), terrazo dado/wall tiling and skirting. etc on brick or stone walls etc including racking out joints hacking for key and scrubbing removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified..

S&F PVC (SWR) 110mm bore pipes, single socketed, in any length with rubber ring joints, fixed to walls with and including MS clamps including taking down existing eaves gutters and rain water pipes (any size or pattern ), including all fittings, heads, shoes, bends, swan necks, etc. (measured overall as fixed along the centre line over fittings and accessories)

Fixing only in repairs, PVC (SWR) 110mm bore pipes, single socketed, in any length with rubber ring joints, fixed to walls with and including MS clamps including taking down existing eaves gutters and rain water pipes (any size or pattern ), including all fittings, heads, shoes, bends, swan necks, etc. (measured overall as fixed along the centre line over fittings and accessories)

S&F 110 mm bore PVC (SWR) bends of any radius / shoe, fixed to PVC pipes as directed.

S&F in repairs 125 mm size CP grating of best quality.

S & F 75 mm bore cast iron (spun) soil, waste and vent pipes, ISI marked in any length with or without ears, with cement joints, laid in trenches including dismantling of existing drain pipes, jointed in cement mortar all as directed.

All as per item No 112 above but except pipe.

S & F 100 mm bore cast iron (spun) soil, waste and vent pipes, ISI marked in any length with or without ears, with cement joints, laid in trenches including dismantling of existing drain pipes, jointed in cement mortar all as directed.

All as per item No 114 above but except pipe.

Extra over cast iron pipes and fittings of size 75mm bore if lead joint is provided in lieu of cement joint complete.

Extra over cast iron pipes and fittings of size 100mm bore if lead joint is provided in lieu of cement joint complete.

S&F in repairs 75 mm dia stainless steel floor trap with grating incluing jointing to waste pipe fixed in cement concrete (1:2:4) type B-1, complete all as specified.

S & F in repairs 100 mm dia cast iron branch pieces, double (equal or un-equal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete.

Fixing only CI fittings 75/ 100mm size of any type and description complete.

S & F in repairs 100 mm bore cast iron bends (any radius), diminishing pieces or tapers (large bore measured) without oval access door.

S & F in repairs 75 mm bore cast iron bends (any radius), diminishing pieces or tapers (large bore measured) without oval access door.

S & F in repairs oval access door cover to CI pipes of 75mm bore with rubber washer packing, bolts and nuts as required complete .

S & F in repairs oval access door cover to CI pipes of 100mm bore with rubber washer packing, bolts and nuts as required complete .

S&F in repairs PVC waste pipe with socket suitable for connection to waste fittings of 32/40 mm dia, and of length minimum 75 cm complete all as specified and directed.

S&F in repairs 75mm cast iron Cowls.

S&F in repairs 100mm cast iron Cowls.

M&L for rendering 15 mm thick in cement mortar (1:6) on internal wall surfaces of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement including taking down old cement plaster including raking out joints hacking for key scrubbing down with water etc and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.

M&L for rendering 15 mm thick in cement mortar (1:4) on external wall surfaces of brick work or concrete surfaces even and fair without using extra cement mixed with liquid water proofing material as per manufacturer's instruction including taking down old cement plaster including raking out joints hacking for key scrubbing down with water etc and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified. (Liquid water proofing material shall be measured and paid for separately.)

M&L for rendering 5 mm thick in cement mortar in (1:3) finishing the surfaces even and smooth on ceiling including taking down old cement plaster and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.

M&L for providing cement concrete (RCC/ PCC) 1:2:4, type B-0 (using 12.5mm graded aggregate) as in broken or cracked chajjas, RCC column, beams, stairs/ steps etc in one or two layers as required (thickness from 25mm to 50mm) and finishing the surface with 15mm thick cement plaster in cement mortar (1:4) including taking out loose/ cracked concrete portion and plaster etc and applying neat cement slurry before concrete work, complete all as specified. Note : 1. Rates deemed to include for any scaffolding/ ladders, form work etc or any other mean to work in two story buildings including welding of reinforcement to be provided for repairs of chajjas, beams, columns, staircase, fins and facia etc. 2. The reinforcement shall be measured and paid separately.

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls, built in CM (1:4), including demolition of old brickwork or stone masonry of any type.

M & L for Brick work using old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6), including demolition of old brickwork or stone masonry of any type.

All as per item No 133 but except bricks. Note : The rate includes for cleaning of old bricks.

M&L for 75 mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in plinth protection finishing the surface even and smooth without using extra cement.

M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

S & F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5 cm but not exc 10 cm, dia of neck 11 to 15mm.

M & L for RCC (1:2:4) type B1 using 20 mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies and in kitchen shelves and the like, finished exposed surface fair and even including demolition of RCC of any description. (Reinforcement and form work shall be measured and paid separately)

M & L for precast cement concrete (1:2:4) type B1 using 20mm graded stone aggregate in landings, cover slabs (for manholes etc), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar (1:4).

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (horizontal or sloping) for flat rough surfaces of concrete.

S&F 1000 litres capacity Rotational moulded polyethylene in white colour, three layered, water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of old water tank of any size and any type and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc all as directed.

S&F 500 litres capacity Rotational moulded polyethylene in white colour, three layered, water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of old water tank of any size and any type and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc all as directed.

S&F ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe of size 20 mm bore (minimum weight 210 gram).

S&F in repairs gun metal, globe or gate valves, heavy duty, with iron wheel head, screwed both ends for iron pipe of 20 mm bore dia.

M & L for preparation of newly plastered surfaces of internal walls and applying the following:- (i) Applying wall care putty in two coats on wall surfaces & smoothening the surface with sand papers/ mechanized sanding etc (preparatory to paint as directed) complete all as specified. (ii) Two coats of 100% acrylic emulsion distemper by using airless spray/ roller over and including a coat of acylic internal primer. Note :- Contractor may use manual tools for surface preparation with prior approval of Engg- in- charge in writing in case use of mechanical equipments are not possible.

Complete removal of existing treatment on wall (any number of layears) by scrapping with steel wire brushes or any other means, including filling depressions of scrapped surfaces and M & L for preparation of old plastered surfaces of internal walls and applying the following:- (i) Applying wall care putty in two coats on wall surfaces & smoothening the surface with sand papers/ mechanized sanding etc (preparatory to paint as directed) complete all as specified. (ii) Two coats of 100% acrylic emulsion distemper by using airless spray/ roller over and including a coat of acylic internal primer. Note :- Contractor may use manual tools for surface preparation with prior approval of Engg- in- charge in writing in case use of mechanical equipments are not possible.

M & L for preparation of newly plastered surfaces of externall walls and applying the following:- (i) Applying wall care putty in two coats on wall surfaces & smoothening the surface with sand papers/ mechanized sanding etc (preparatory to paint as directed) complete all as specified. (ii) Two coats of weather proof (antifungal) exterior emulsion paint by using airless spray/ roller over and including a coat of exterior emulsion primer. Make:- Apex Brand of Asian Paints/Excel Brand of Nerolac Paints/Berger Weather Coat Note :- Contractor may use manual tools for surface preparation with prior approval of Engg- in- charge in writing in case use of mechanical equipments are not possible.

Complete removal of existing treatment on wall (any number of layears) by scrapping with steel wire brushes or any other means, including filling depressions of scrapped surfaces and M & L for preparation of old plastered external surfaces of walls and applying the following:- (i) Applying wall care putty in two coats on wall surfaces & smoothening the surface with sand papers/ mechanized sanding etc (preparatory to paint as directed) complete all as specified. (ii) Two coats of weather proof (antifungal) exterior emulsion paint by using airless spray/ roller over and including a coat of exterior emulsion primer. Make:- Apex Brand of Asian Paints/Excel Brand of Nerolac Paints/Berger Weather Coat Note :- Contractor may use manual tools for surface preparation with prior approval of Engg- in- charge in writing in case use of mechanical equipments are not possible.

M&L for preparation of old decorated, plasterered/ unplastered or concrete surfaces on walls including cornices and pillers etc, by brooming down, steel wire brushing, scraping down loose layers, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc complete and applying two coats of white wash on these surfaces complete.

M&L for applying three coats of white wash on newly plastered surfaces of internal wall including preparation of surfaces.

M&L for preparation of old decorated, plasterered/ unplastered or concrete surfaces on ceiling including cornices and pillers etc, by brooming down, steel wire brushing, scraping down loose layers, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc complete and applying two coats of white wash on these surfaces complete.

M&L for preparation of newly plastered or unplastered surface and applying three coats of white wash on ceilings.

M & L for painting to old steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with one coat of synthetic enamel paint including preparation of old painted surfaces.

M & L for painting to old wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with one coat of synthetic enamel paint including preparation of old painted surfaces.

Preparing surfaces of wood and wood based materials, new or old, of any description or girth, not otherwise described and treated with two coats of creosote.

Internal Electrification

Taking down carefully existing unserviceable copper / aluminum point wiring (light, fan, socket) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, light fittings etc and removing the retrieved materials from site including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and directed.

M & L for point wiring with multi stranded copper conductor FRLSH cable, 1100 volts grade PVC insulated and unsheathed of size 1.5 Sqmm single core in and including PVC concealed conduit not less than 20mm dia ( medium duty ISI marked) and conduit fittings with and including replacement of mild steel/ pressed steel sunken box and outer sheet and provision of fixed concealed modular type sunken box with inner and outer cover including all screw, cup washer used to brass etc for one fan / light controlled by one switch including provision of 1.5 Sqmm PVC insulated & unsheathed with single core, multi stranded copper conductor FRLSH cable as earth wire to common earth & connecting to earth dolly all as specified and directed.

All as per item No 157 here in before but for socket outlet 5 pin, 6 Amp on same board complete all as specified.

All as per item No 157 here in before but for socket outlet 5 pin, 6 Amp on independent board but not below the switch board complete all as specified .

All as per item No 157 here in before but for one socket outlet 6 pin, 6/16 Amp multipurpose 2 in 1 on independent board with cable of 2.5 Sq mm, multi stranded copper conductor FRLSH cable including provision of 2.5 Sq mm PVC insulated solid copper conductor FRLSH cable continuos as earth wire connected to earth dolly, conductor etc.

All as per item No 157 above but for call bell/buzzer point.

All as per item No 157 above but for one light point controlled by two switches two way.

S & F Switch modular, single module, one way, 5/6 Amp .

S & F Switch modular, single module, two way, 5/6 Amp .

S & F Switch modular, single module, one way, 15/ 16 Amp .

S & F Modular type socket, multipurpose, 2 in 1, 5 Pin, 6 Amp, two module etc. (Note: Switch and socket shall be of same make.)

S & F Modular type socket outlet universal, multipurpose, 2 in 1, 3 Pin 6 Amp and 6 pin 16 Amp, two module etc. (Note: Switch and socket shall be of same make.)

S&F Modular type Blanking plate one module complete all as specified.

S&F, Modular type fan regulator electronic step type (1-5), two module, 230-240 Volt, AC supply, complete all as specified and directed.

S&F 6 Amps bell push modular switch,single module, 230 volts AC, ISI marked complete all as specified and directed.

M & L for point wiring with multi stranded copper conductor FRLSH cable, 1100 volts grade PVC insulated and unsheathed of size 1.5 Sqmm single core in and including PVC concealed conduit not less than 20mm dia ( medium duty ISI marked) and conduit fittings with and including 3 mm thick bakelite laminated sheet top cover for one exhaust fan / light/ fan controlled by one switch including provision of 1.5 Sqmm PVC insulated & unsheathed with single core, multi stranded copper conductor FRLSH cable as earth wire to common earth & connecting to earth dolly all as specified and directed.

All as per item No 171 here in before but for socket outlet 5 pin, 6 Amp on same board complete all as specified.

All as per item No 171 here in before but for socket outlet 5 pin, 6 Amp on independent board but not below the switch board complete all as specified .

S & F Switch semi modular with frame, flush type, single pole, one way, 5/6 Amp .

S & F Semi modular switch socket combination, 5 Pin, 6 Amp, flush type, including decorative frame cover. (Note: Switch and socket shall be of same make.)

S&F Blanking plate complete all as specified.

S&F, fan regulator electronic step type (1-5), socket type 230-240 Volt, AC supply, complete all as specified and directed.

S&F electric / electronic bell, ding dong type, 230 Volt, AC supply complete all as specified.

S&F ceiling rose, 3 plate, surface bakelite type, Polycorbonate body, 6 Amps, 250 Volts AC, 20x50 mm, three terminal (ISI marked) complete all as specified.

S & F, In repair, Lamp holder of PVC/Polycarbonate type with back plate suitable for batten fitting including 9 watt LED bulb.

S & F MCB, SP, 6 to 32 Amps, 'C' curve, 230 Volts, breaking capacity not less than 10 KA with over load and short circuit protection including taking down old unserviceable MCB complete all as specified.

S & F MCB, SPN, 40 Amps, 'C' curve , 230 Volts, 50 Hz, breaking capacity not less than 10 KA with over load and short circuit protection and including taking down old unserviceable MCB complete all as specified.

S & F MCB, SPN, 63 Amps, 'C' curve , 230 Volts, 50 Hz, breaking capacity not less than 10 KA with over load and short circuit protection and including taking down old unserviceable MCB complete all as specified.

S & F sheet metal enclosures double door made out of CRCA mild steel sheet, concealed, surface mounting, acrylic door, IP-43 protection, 8 way, DB SPN 230 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc including taking down old unserviceable DB.

S & F sheet metal enclosures double door made out of CRCA mild steel sheet, concealed, surface mounting, acrylic door, IP-43 protection, 12 way, DB SPN 230 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc including taking down old unserviceable DB.

S & F single pole and neutral enclosure with two pin and earth plug and metal top DB 230 Volts complete with neutral and earth link and 200 Amp rated bus bar complete made out of CRCA mild steel sheet including taking down old unserviceable DB.

M & L for sub main wiring with 2 single core cable PVC insulated unsheathed of copper multi strandard conductor FRLSH cable of size 6 sqmm, 1100 votls grade drawing through in and including PVC concealed conduit 20 mm dia medium duty including acessories such as Tee, bend, Elbow etc, ISI marked with and including PVC insulated 6 sqmm unsheathed multistranded FRLSH copper conductor cable for earth continuity and connected to common earth dolly including cutting chasing of wall, if required and making good disturbed surface in CM (1:3) and finishig the surface to match with existing surface etc including taking down old unserviceable wiring 6 Sqmm complete all as specified. Note:- Two runs of cable, one run of earth wire and one run of PVC conduit shall be measured as one unit.

M & L for sub main wiring with 2 single core cable PVC insulated unsheathed of copper multi strandard conductor FRLSH cable of size 4 sqmm, 1100 votls grade drawing through in and including PVC concealed conduit 20 mm dia medium duty including acessories such as Tee, bend, Elbow etc, ISI marked with and including PVC insulated 4 sqmm unsheathed multistranded FRLSH copper conductor cable for earth continuity and connected to common earth dolly including cutting chasing of wall, if required and making good disturbed surface in CM (1:3) and finishig the surface to match with existing surface etc including taking down old unserviceable wiring 4 Sqmm complete all as specified. Note:- Two runs of cable, one run of earth wire and one run of PVC conduit shall be measured as one unit.

S & F 18/20 watt Retro LED tube light fitting, wall/surface mounted, IP 20 protection, conforming to IS 16106/IS 16107, minimum 6000K batten decorative type 4 feet long polycarbonate body, white, in built LED driver, power factor>0.95 , Make all as per Crompton Cat Part No. DMLN1LT8-16 (for batten) and Cat part No. LT8-20-865-2 (for tube light) including 18/20 watt tube rod or equivalent model of any make given in Appx 'B' connecting to electric point by using PVC insulated twin core copper conductor cable of suitable size including taking down old existing light fitting all as directed.

S & F LED mirror light fitting of 12/14 watt, 6000K, linear & compact with decorative grey end caps, polycarbonate body and ribbed opal diffuser complete including 12/14 watt tube rod all as model No LCL-14-CDL of Crompton with 14 watt rod or equivalent model of approved make from list of make attached in tender documents including connecting to electric point by using PVC insulated twin core copper conductor cable of suitable size including taking down old existing light fitting.

S & F surface mounted, decorative round plastic comprising of high brightness LED lamp 10/12 watt, 6000K polycarbonate including all other accessories and fitting arrangement including electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector. Make:-Crompton cat part No LCSR-12-CDL or equivalent model of approved make from list of make attached in tender documents including taking down old existing light fitting.

S & F wall mounted/surface mounted decorative wall light fixture in cylinderical profile made up of polycarbonate suitable for and including LED lamp of 7 watt B22 base complete fitting and all other fixing accessories including electric connection with flexible copper wire twin core including taking down old existing light fitting. Make:- Crompton Cat part No. DCWL 15 DF or equivalent model of approved make from list of make attached in tender documents Note:- The rate of LED lamp of 7 watt B22 base is deemed to be included in quoted rate.Nothing extra shall be paid on this account.

S & F surface mounted, decorative round plastic bulk head luminaire comprising of high brightness LED lamp 10/12 watt, 6000K polycarbonate including all other accessories and fitting arrangement including electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector. Make:-Crompton cat part No LBHE-10-CDL or equivalent model of approved make from list of make attached in tender documents including taking down old existing light fitting.

S & F energy efficient LED street light fitting of 25 Watt with PDC aluminium body and clear glass with lens for wide beam distribution, top maintainable type with IP 66 degree of protection, PF>0.95 with voltage range 140 to 270 Volt, fitting should be provided with inbuilt 5 KV minimum surge protection, short circuit and over voltage protection facility for Driver and fitting including 25 watt LED lamp with GI brackrt-01 No, MS clamp-02 Nos suitable for walls/ columns and making electrical connection with providing of 1.50 metre long twin core round copper conductor cable of suitable size and testing complete all as per SYSKA cat part No. SSK-SLF-CF-25W-WL or equivalent model of any make given in Appx 'B', Cat Part No. as approved by GE complete all as specified including taking down old unserviceable existing street light fitting of any type and capacity from pole along with accessories.

S & F heavy duty Exhaust fan 300mm sweep single phase 230V, 50 Hz, 900 RPM complete with louvers, frame and acessories and connecting up using suitable size copper conductor flexible cable from existing ceiling rose to fan complete.

S & F PVC body Exhaust fan 250mm sweep single phase 230V, 50 Hz, 1400 RPM complete with louvers, frame and acessories and connecting up using suitable size copper conductor flexible cable from existing ceiling rose to fan including making hole for proper fitting of exhaust fan, louvers and making good with existing finishing complete.

S & F ceiling fans BEE 5 star rating, 1200 mm sweep 230 V, energy efficient type white coloured with down rod, rubber reel, nut, bolts, washerclamps, canopys and connecting up using suitable size copper conductor flexible cable from existing ceiling rose to fan complete.

Supply, installation, testing and commissioning of water heater storage type (BEE 5 star rating), electrically operated, single phase, 230V, 50Hz of capacity 25 ltrs with vent pipe, fusible plug, thermostat, safety valve, proper earth connector, SS tank complete with all accessories required for plumbing work (Inlet and outlet GI pipe), grouting bolts and nut etc, inlet and outlet pipe connection (CP) including one NRV, one bib tap and one stop cock complete.

S & F rigid non-metallic PVC conduit exclusive of boxes (junction/ terminal) but inclusive of all tees, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe of hook etc 20mm dia, 2mm thick PVC conduit pipe ISI marked conceled/ surface above false ceiling, if necessary with all required accessories including chislling of wall whereever necessary including masonry work for telephone, TV, LAN cable complete.

M&L for wiring with twin core PVC insulated sheath with copper conductor having single strand of 0.6mm dia tapped for telephone wiring from terminal box to telephone socket complete.

M&L for wiring with TV coaxial RG 6 heavey duty PVC insulated seath with copper conductor having single strand of 0.7mm dia and copper wire net for TV antena from terminal box to TV socket complete.

M&L for Mild steel box flush mounted 100mmx 100mmx 100mm having holes for 6mm conduit entry including 3 pin telephone socket outlet flush type duly marked with symbol of telephone and 3 mm thick plastic laminated sheet cover complete for telephone connection complete.

M&L for Mild steel box flush mounted 100mmx 100mmx 100mm having holes for 20mm conduit entry including 2 pinTV socket outlet flush type duly marked with symbol of TV and 3 mm thick plastic laminated sheet cover complete for TV connection complete.

Supply, installation, testing and commissioning of factory made meter panel board of size 1100 x 900 x 300mm, wall mounted made out of CRCA sheet 2.00 mm thick indoor type totally enclosed weather proof, dust and vermin proof with front openable, hinged door locking arrangement mounted on MS clamp welded to panel body duly grouted in wall including provn of Acriylic sheet for meter reading, space for refixing of single phase KWH meter 5-60 Amps -05 Nos AC 230 Volts incl lugs, spacer mounting chanels, rubber gasket, locking knobs, PVC shrinkable sleeves, nut bolts, washers etc, suitable compartment of every meter and control MCB circuit and epoxy powder coated spray paint with primer and M & L for the following accessories and taking down old panel and its accessories and making surface good as per existing complete (for four qtrs) :- (a) MCCB 04 pole, 63 Amp, 415 Volts 16 KA - 01 No (incommer) (b) MCB SP 63 Amp, 230 Volts 10 KA - 04 Nos (outgoing) (c) MCB SPN 06 Amp, 230 Volts 10 KA - 01 No (outgoing) (d) R,Y,B LED Indicator - 03 Nos (e) Copper bus bar 200 Amp capacity TPN (f) Copper wiring in panel with suitable size cable. (g) Surge protection device class -II (T-2) low voltage 4 pole 40 KA (g) Re-fixing existing electric meter- 05 Nos ( Note : To be insure properly maching the qtr Nos before fixing the electric meter)

M & L in replacement of earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground to depth of pit not less than 2.25 m below normal ground level with top edge of the plate not less than 1.5 m below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal / coal dust and common salt filling in alternate layers and connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI or steel including GI protection pipe 15mm dia light grade upto the extent of 7.5 metre and connecting to earthing test point, main switch board including GI pipe 20 mm dia light grade for watering, MS funnel and bringing out the watering pipe upto 30 cm above the normal ground level plugged at top including all fitting including PCC earth pit with PCC 1:2:4 type B-1 using 20mm graded stone aggregate and RCC pit cover including necessary earthwork and excavation in any type of soil complete all as specified as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note :- (a) PCC chamber shall be constructed at least 1.5 m away from earth pit. Pipe for watering shall be provided in slanting manner. (b) 4mm dia GI wire and 15mm dia light grade GI protection pipe upto 7.5 metre shall deemed to be included in quoted rate.

RINKU BROTHERS

M/s Balvinder Singh Engineer and Contractors

SUBHASH ARORA CONSTRUCTION CO

M/s Kamal Builders

KARTIK BUILDERS