Special Repair to Md Accn Bldg No P-18/01 to 10 at Old Umrao Colony at Mil Stn Bikaner under GE (N) Bikaner

Taking down cement plaster/terrazo finish on brick or stone wall etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed.

M&L for 10mm thick Rendering in cement mortar 1: 6 on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick Rendering in cement mortar 1: 4 on fair faces of brick work or concrete surfaces, finished fair and even without using extra cement using integral liquid water proofing compound complete all as specified and as directed. Note : WPC shall be measured and paid seperately.

M&L for 5 mm thick Rendering in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified and as directed.

M&L for Preparing new plastered or unplastered surfaces of ceiling and applying two coats of white wash over 2mm wall putty , white or tinted complete all as specified and as directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 2mm thick wall care putty on new surfaces including preparation complete all as specified and as directed.

M&L for Preparing new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over 2 mm thick putty complete all as specified and as directed.

Supply only liquid water proofing compound ISI marked @ 200ml per 50Kg of cement content complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for 75mm thick Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, , finished even and smooth using extra cement , laid in panels including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and as directed.

M&L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and as directed.

M&L for double charged Vitrified tiles 10mm thick (square/rectangular) size 600mm x 600mm, in floors on using chemical adhesives and pointed in white or coloured cement to match complete all as specified and as directed. (Adhesive shall be measured and paid separately)

All as per item No 12 hereinbefore but on vertical surface over and including 10mm thick rendering in Cement mortar 1:4 complete all as specified and as directed.

Dismantling of floor hearth or existing terrazo dado /flooring or tilles in bath .WC and kitchen etc complete all as specified and as directed.

M&L for Non skid Ceramic coloured tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors over and including 20mm thick screed bed in CM 1:4. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for Ultracharged Vitrified Ceramic tiles 600mm x 300mm x 10mm thick dark shade (square /rectangular) polished, on vertical surfaces/skirting using chemical adhesives over and including 10mm thick rendering in CM 1:4. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed. (Adhesive shall be measured and paid separately)

Demolition of stone slabs / kota / Marble in floors of any description or thickness laid, bedded and pointed in any mortar complete all as specified and as directed.

M&L for 16-18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like over and including 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

All as per item No 18 hereinbefore but on vertical surfaces as in riser of steps, skirting, dado etc over 10mm thick rendering in Cement mortar 1:4 complete all as specified and as directed.

M&L for Anti termite treatment of soil under existing floor using chemical emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors complete all as specified and as directed.

M& L for Anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed.

M&L for demolition of sunken filling concrete, removal of loose concrete and cleaning the surface and after proper cleaning filling the cracks with polymer modified mortar using Dr fixit pidicrete URP and providing 50mmx50mm angle fillets on the vertical upstands, parapet wall junction corners, service units and properly dressed by preparing polymer modified mortar with DR Fixit pidicrete URP in the ratio of 1:3 by adding polymer 10% by weight of the cement, add the water little little unit the required consistency is achieved and thereafter providing and applying two coats of acrylic polymer modified cementitious coating Dr Fixit pidifin 2K of M/s Pidilite Industrieshaving elongation at break 50% 5 bar resistance to positive water pressure, Adhesive strength ASTM D 7234-1 N/mm sq, water vapour transmission as per ASTM E96 of 030 perms and crack bridging ability as per EN 1062-7 upto 1 mm. Apply two coats of Dr Fixit pidifin 2K slurry “ coverage of 0.55-0.58 Sqm/kg of mix slurry. Provide and lay 45 gsm glass fibre mesh over the angle fillet when the first coat is still wet. Allow the first coat to dry for 6-8 hours, then apply the second coat at a direction perpendicular to first coat. Allow the coating to air cure for 5 days before conducting water ponding test for 24 hrs etc or other equivalent product as approved by GE in sunken area complete all as per the manfactures instruction, including removing rubbish material from building and thrown in low lying empty area at any distance out side MD land complete all as specified and as directed.

M&L for rendering 10 mm thick in cement plaster (1:3) using coarse sand finished even and smooth without using extra cement with steel trowel on sunken surfaces using integral water proofing compound complete all as specified and as directed. ( WPC shall be measured and paid separately)

S&F in repair Wall mounting EWC white size 515 x 360 x 350 mm (excluding flushing cistern) complete all as specified and as directed.

S&F in repair Concealed PVC flush cistern size 550 x 95 x 500 mm complete all as specified and as directed.

S&F in repair Table top Vitreous chine wash basin size 600 x 405 x 155mm including waste CP brass complete all as specified and as directed.

S&F single lever central Hole Basin Mixer 15mm bore dia with letter marked for cold and hot complete all as specified and as directed.

S & F in repair brass chromium plated bib cock long Nose body Fancy type with capstan screwed down for iron pipe 15 mm bore complete all as specified and as directed.

S & F in repair angle valve cock chromium plated fancy type half/full turn for iron pipe 15 mm bore screwed down high pressure, with capstan head, screwed both ends for iron pipe or for union complete all as specified and as directed.

S & F in repairs for Brass chromium plated High flow diverter including upper part of diverter, spout, hand(mobile) shower 100mm with 1.5meter shoer faucet set complete all as specified and as directed.

S&F 32 mm bore stainless steel bottle trap set with waste outlet pipe for wash basin/Kitchen sink with coupling complete all as specified and as directed.

S & F repair PVC connection 15 mm size brass nuts of length 450 mm complete all as specified and as directed.

S & F in repair sinks made of stainless steel kitchen sink with drainage board, plugs washers and waste copling including bedding in cement mortar to dwarf wall or including supply and fixing cantilever brackets of MS angles and connecting union to 800 mm long PVC waste flexible pipe 40 mm dia, over all size 914 mm x 460 mm x 203 mm and bowl size 405 mm x 354 mm x 203 mm complete all as specified and as directed.

S&F Kitchen Rack/Dish Rack (Kitchen stand or wall mounted) of size 914mmx787mmx250mm (Appx size) of Make Prayag Cat Part No P-348 or equilent made out of Food grade stainless steel 0.6 mm thick sheet/strip including necessary arrangements of plates and utensils to keep (Holds up to many plates or bowls to accommodate several place settings, Multipurpose), stylish modern streamline design, rust resistant, easy to assemble and clean including fitting accessories complete all as specified and as directed.

Taking up or down steel tubing and connections 15 mm bore complete all as specified and as directed.

Taking up or down 20mm bore steel tubing and connections, complete all as specified and as directed.

Supplying and laying of CPVC pipes of 20 mm dia SDR 11 & Plain CPVC SDR 11 fittings in trenches, wall((100mm away from wall using sutaible clamps) complete all as specified and as directed.

Supplying and laying of CPVC pipes of 25 mm dia SDR 11 & Plain CPVC SDR 11 fittings in trenches, walls(100mm away from wall using sutaible clamps) complete all as specified and as directed.

S&F CPVC Union 25mm complete all as specified and as directed.

S&F CPVC 25mm male/female brass threaded adaptor(FTA/FBTA) complete all as specified and as directed.

S&F CPVC 20mm male/female brass threaded adaptor(FTA/FBTA) complete all as specified and as directed.

S&F CPVC 20mm Brass Tee complete all as specified and as directed.

S&F in repair triple layer Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, hoisted and fixed in position including connecting up pipes complete all as specified and as directed.

S&F in repairs Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore (minimum weight 210 gms) complete all as specified and as directed.

Taking down eaves gutters and rain water PVC pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-neck etc (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

Dismantling cast iron pipes of any description any dia complete all as specified and as directed.

S&F 110mm PVC(SWR)single pipe socketed soil waste and vent pipe in any length with rubber ring joint laid in trenches or in floors complete all as specified and as directed.

S&F 110mm PVC(SWR)single pipe socketed soil waste and vent pipe in any length with rubber ring joint fixed to wall(100mm away from wall using sutaible clamps) complete all as specified and as directed.

S&F 75 mm PVC(SWR)single pipe socketed soil waste and vent pipe in any length with rubber ring joint fixed to wall(100mm away from wall using sutaible clamps) complete all as specified and as directed.

S&F PVC(SWR) bends,110mm. Bore complete all as specified and as directed.

S&F 110mm. Bore PVC (SWR) junction single,(Single T) equal or unequal with access door complete all as specified and as directed.

S&F PVC(SWR) floor trap 75mm incl.CP grating jointing with solvent complete all as specified and as directed.

S&F PVC (SWR) 110mm to 75mm reducer complete all as specified and as directed.

S&F 75 mm PVC (SWR) vent cowl complete all as specified and as directed.

S&F 40 mm PVC single pipe socketed waste and vent pipe in any length including bend, reducer joint with solvent fixed to wall, in floor complete all as specified and as directed.

S & F in repair CPVC Ball valve for CPVC pipe of 20/25 mm dia complete all as specified and as directed.

S&F in repairs Glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and as directed.

S&F Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flangess complete all as specified and as directed.

S& F chromium plated soap dish Holder with round flange, fixed on wall with chromium plated brass screws and PVC plug complete all as specified and as directed.

S&F Corner glass shelf of size 300mmx200x150mm fancy type, toughned glass, with CP bracket and guard railing, fixed along wall with CP brass screws and PVC plug complete all as specified and as directed.

M&L for 25mm dia stainless steel chromium plated curtain rod incl bracket & knobs fixed in position complete all as specified and as directed.

Taking down window/chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprisingof virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprisingof virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and as directed.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S & F Factory made single extruded WPC (Wood Polymer Composite) skeleton door solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, ater/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprisingof virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and as directed.

Supply and fixing 100mm long stainless steel butt hinges heavy duty including steel screws for fixing complete all as specified and as directed.

Supply only adhesive of good quality to fix floor tiles of make Sika or equivalent out of makes specified in list of makes complete all as specified and as directed.

S&F stainless steel sliding door bolt 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed and complete all as specified and as directed.

S&F stainless steel barrel tower bolts of extruded section 200 mm long complete all as specified and as directed.

S&F stainless steel barrel tower bolts of extruded section 150 mm long complete all as specified and as directed.

S&F stainless steel handles cast type anodised, 125 mm size complete all as specified and as directed.

S&F 300 mm, ordinary rat tail rod pattern springs of mild steel including roller and roller plate complete all as specified and as directed.

S&F for Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples and complete all as specified and as directed.

S&F 5mm thick Figured glass, pin head type and glazing with beads (either supplied with shutters or to be measured separately as supply only) in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F 4.80mm thick Sheet glass , ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised with 40mm width of flaps (when open) and complete all as specified and as directed.

S & F HDHMR board, 18/19mm thick, density over 850kg/cum, having a class A fire rating, grade 2 quality, commercial type, as in cupboard complete all as specified and as directed.

S&F Satinless steel 100mm Hasp and staple, safety type,fixed with screws complete all as specified and as directed.

S&F stainless steel 125mm handle cast type, anodized complete all as specified and as directed.

S&F stainless steel 150 mm floor door stopper double leg with insulation tounge complete all as specified and as directed.

S&F Carbon metal seal door strips with rubber insulation 90cm x 4 cm complete all as specified and as directed.

M&L for preparation of old interior surface of walls including complete removal of existing treatment by mechanical equipment like electric sander and applying two coats of oil bound distemper over 2 mm thick putty complete all as specified and as directed.

M&L for Preparing old ceiling including complete removal of existing treatment by mechanical equipment like electric sander and and applying two coats of white wash over 2mm wall putty , white or tinted complete all as specified and as directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces including complete removal of of existing treatment complete all as specified and as directed.

M&L for Roof treatment in as specified below and as directed: (a) Removal of existing PCC/Brick bat Coba/Mud phuska/ APP membrane from the roof stacking the reusable material and disposal of unserviceable rubbish outside the campus as direction by Egineer-in-Charge but outside in 3 km. (b) 15mm thick rendering in CM (1:4) over existing / old RCC slab / surfaces after dismantling / demo / taking down existing roof treatment. (c) Cleaning of surface of loose dust, and dirt and cement slurry etc, by means of wire brush, dust removing brush and scraper etc, Pot holes / Cracks shall be repaired with cement admixed with polymer as per manufacturer instructions. (d) Providing PCC coving / gola along vertical parapets of size 75mm x 75mm with concrete Mix (1:2:4), type B-1 using water proofing compound of approved make etc, complete as directed by Engineer-in-Charge (e) The surface shall be treated with PU Elastrol primer with Epoxy primer to seal the pores and enhance the adhesion of the coating, supplying and applying single component waterproofing liquid membrane based on pure, elastomatric, polyurethene resin cold applied of spray/brush applied membrane with an elongation of 650% +/- 50 and tensile strength not less than 2 Mpa, crack bridging ability not less than 2mm. No leakage upto 5 bars of water pressure. shore Hardness > 50 Shore.The minimum thickness to be applied shall be 1.5 mm , (overall) in two layers (each layer 750 micron) or as per manufacture's instructions so as to achieve thickness not less than 15mm. (f) Providing & laying of protective Geotextile fabric 150 GSM over the entire membrane with proper overlaps of 75mm before laying SRI roof tiles. (g) Providing and laying SRI (Sun Resistance Index) roof tiles (Size 300 x300 x 9-10mm with 20mm thick cement plaster in CM (1:4) mixed with liquid water proofing compound as per manufacturer's instructions confirming to required slope.

Demolition of brick work built in cement mortar including all quions arches pillars etc complete all as specified and as directed.

M&L for brick work with sub class B bricks straight or curved on plan exc 6m mean radius brick walls built in CM 1:6 complete all as specified and as directed.

Dismantling strucural steel work including door gates but excluding framed truss etc complete all as specified and as directed.

S&F framed work such as grills ,framed guard bars barred iron doors ;ladders framed balusters railings and similar work conforming to Fe 410-0or Fe 310-0 complete all as specified and as directed.

M & L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

Demolition of cement conc. Reinforced as in staircase , beams chhajas and similar suspended work reinforced cut required to facilitate demolition complete all as specified and as directed.

M&L for RCC Design Mix of M-25 Grade for Chullah hoods; stairways (except spiral staircases) including steps (square or spandril), string pieces, carriages, etc., complete, any section straight or winding, but excluding landings; RCC water tanks upto 1500 litre complete all as specified and as directed.

M&L for RCC Design Mix of M-25 Grade for chajja and like using 20 mm graded stone aggregates complete all as specified and as directed.

M&L for Form work to soffits of suspended slab such as roof slab not exc 200 mm thick to rough finished surface of concrete complete all as specified and as directed.

M&L for Formwork to staircases with sloping or stepped soffits including risers and stringers (excluding landing) complete all as specified and as directed.

M&L for Form work to chullah hoods, chajjas, troughs and similar items including edges to rough finished surface and complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

M&L for Mild steel TMT bars8- 10mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

Structural design for Existing Roof Slab, Beams, Chajja, staircase and other connected RCC members required to be re-constructed under this Schedule with & including vetting of structural design from approved Govt Engineering College/NITTTR/CBRI, complete all as specified and as directed. Notes : (i) Tenderer shall carryout the site visit to ascertain the size of slab, other RCC members, arrangement of rooms, etc required for design purpose.(ii) Four sets of Structural drawings shall be provided to GE by the contractor duly vetted as above complete all as specified and as directed.

M&L for 100 mm thick PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in sub base complete all as specified and as directed.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed.

M&L for Providing precast cement concrete type B1, 1:2:4 using 20mm graded stone aggregate as in string course (kerb stone) with plain fair faces including chamfers, weathering complete all as specified and as directed.

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in loose/soft soil complete all as specified and as directed.

Demolition of cement conc. Reinforced as in roof slab , beams chhajas and similar suspended work reinforced cut required to facilitate demolition complete all as specified and as directed.

Demolition and breaking up drain pipes (SGSW, AC or RCC) of internal dia 150mm, set in cement mortar complete all as specified and as directed.

M&L for Cement concrete 1:3:6 type C2 Concrete bed(width of bed is outer dia of pipe plus 30 cm) to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed.

M&L for DWCPE (SN8) confirming to IS-16098,150 mm Nominal bore (160 mm OD) complete laiding and jointed incl testing along with necessary jointing material tees /union /socket etc complete as per manufacture instructions complete all as specified and as directed.

M&L for Cutting into existing manholes for connecting new drains, _150___mm bore, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required complete all as specified and as directed.

M&L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in lean concrete foundation complete all as specified and as directed.

M&L for PCC 1:2:4 mix type B-2 (40 mm graded stone aggregate) as in surface channels and drains complete all as specified and as directed.

M&L for PCC 1:2:4 mix type B-1 (20 mm graded stone aggregate) as in coping complete all as specified and as directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and as directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Taking down carefully (aluminium) point wiring complete of any type (batten/ surface conduit or concealed) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as spcified and as directed.

Taking down old U/S existing DB SPN 8 way & TPN DB 4 way including MCB/MCCB/Sheet Metal enclosure plug socket of any capacity and any size and removing from site and making good the disturbed surface of wall etc complete all as specified and as directed.

Disconnecting and taking down unserviceable submain wiring form TPN DB to SPN DB and SPN DB 8 way to SPN DB 4 Way complete & removing U/S items from site complete all as spcified and as directed.

Taking down the old unserviceable Fan regulator from site complete all as spcified and as directed.

Taking out carefully earthing set complete of any type including earthing wire & removing U/S items from site complete all as spcified and as directed.

One light/fan point (Ceiling Fan/Exhaust Fan) controlled by one switch.

One multi pin socket 5/6Amps, Independent.

One 5/6 amp socket outlet on the same board controlled by another switch.

One bell point controlled by one switch

One ligh point controlled by two 02 way switch complete all as specifed and directed

All as per item No 125 here -in- before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.5 sqmm single core PVC insulated and and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 2.5 Sqmm single core PVC insulated and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and as directed .

All as per item No 125 here -in- before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 4 sqmm single core PVC insulated and and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 4 Sqmm single core PVC insulated and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and as directed .

S&F switch Modular type, 5/6 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as spcified and as directed.

S&F switch Modular type, 15/16 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as spcified and as directed.

S&F socket outlet 3 Pin 5/6 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as spcified and as directed.

S&F socket outlet 3 Pin 6/16 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as spcified and as directed.

S&F of bell push, modular type 5 Amps 1 module complete all as spcified and as directed.

S&F ceiling rose, surface backelite , three terminal AC, 230 volt complete all as spcified and as directed.

Taking down Ceiling fan,sealing cable end, dismantling blades of any make, any sweep, and refixing after necessary repairing such as winding of motor, replacement of capacitor & ball bearing of ceiling fan, cleaning all dust & painting with existing colour synthetic enamel paint by spraying including filling cavities with filler,one coat including writing MES No. complete all as spcified and as directed.

Supply and fixing fan step regulator modular type,120W -2 module electronic socket type five step controlled 230V AC 50 Hz for complete all as spcified and as directed.

Supply & Fixing Exhaust fan (Heavy Duty) Steel body AC Single phase 230 Volt,50 Hz,900RPM,size 300 mm sweep with blades and frame including new mosquito stainless steel wire mesh of gauge 0.36 mm with suitable wooden fram eprotection against birds etc including provision of cutting of existing wall for suitable opening as per fan including electric connection with & including new 1.5 Sqmm 2 core flexible copper conductor cable from ceiling rose to fan,fan hanging on wall with 04 Nos steel fastners 10 mm dia 100 mm long and making good disturbed surface with cement mortar complete all as spcified and as directed. Note : (i) Serial no as issued by Engineer-in-Charge of Exhaust Fan and GE Office name shall also be written on Exhaust Fan with red colour permannet marker,cost for the same shall deemed to be included in the quoted unit rate nothing shall be paid extra on this account.

Supply and fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 250 mm sweep with blades and frame including new mosquito stainless steel wire mesh of gauge 0.36 mm with suitable wooden fram eprotection against birds etc including provision of cutting of existing wall for suitable opening as per fan including electric connection with & including new 1.5 Sqmm 2 core flexible copper conductor cable from ceiling rose to fan,fan hanging on wall with 04 Nos steel fastners 10 mm dia 100 mm long and making good disturbed surface with cement mortar complete all as spcified and as directed. Note : (i) Serial no as issued by Engineer-in-Charge of Exhaust Fan and GE Office name shall also be written on Exhaust Fan with red colour permannet marker,cost for the same shall deemed to be included in the quoted unit rate nothing shall be paid extra on this account. with blades and frame including new mosquito stainless steel wire mesh of gauge 0.36 mm with suitable wooden fram eprotection against birds etc including provision of cutting of existing wall for suitable opening as per fan including electric connection with & including new 1.5 Sqmm 2 core flexible copper conductor cable from ceiling rose to fan,fan hanging on wall with 04 Nos steel fastners 10 mm dia 100 mm long and making good disturbed surface with cement mortar. (ii) Serial no as issued by Engineer-in-Charge of Exhaust Fan and GE Office name shall also be written on Exhaust Fan with red colour permannet marker,cost for the same shall deemed to be included in the quoted unit rate nothing shall be paid extra on this account.

Taking down LED tube light fitting, 1x 20 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as spcified and as directed.

Refixing LED tube light fitting, 1x 20 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as spcified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as spcified and as directed.

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as spcified and as directed.

S&F LED Bulb 9W, operating voltage- 220-240 volts, starting time < 0.5s, color temperature-6500K, lumens: min 825 complete all as spcified and as directed.

S&F LED light fitting 1x9W/1X10Wbulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as spcified and as directed.

S&F LED Bldg Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as spcified and as directed.

S&F GI bracket made out of 40 mm bore GI pipe light grade /medume grade, ISI marked, medium grade 1.2m long bent to shape suitable for fixing of street light fitting including with 2 Nos MS clamps made with 40x3mm flat iron, bolts, nuts, washers etc including two coats of synthetic enamel paint over one coat of zinc chrome primer and fixing on electric pole complete all as spcified and as directed.

Taking down and refixing water heater storage type of 25 ltrs capactiy and 1500 watts, BEE Star rated-5, with glass line inner shell with Hot & Cold pipe, water connection pipe, electric connection and necessary repairing/replacement of inner tank, siphon assembly, glass wool, thermostate switch, heating element including washers, 3 core PVC insulated copper conductor cable etc including fixing arrangement complete all as spcified and as directed.

Taking down and refixing tamper proof energy meter electronic type single phase 10-60 Amps current rating single phase 230V AC with electric connection and necessary fixing arrangement complete all as spcified and as directed.

S & F double door, sheet metal enclosure, powder coated for MCB DB SPN 8 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as spcified and as directed.

S & F double door, sheet metal enclosure, powder coated for MCB DB TPN DB 4 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as spcified and as directed.

S& F MCB SP, 5-32 Amps , 240 volts, breaking capacity 10KA complete all as spcified and as directed.

S & F MCB SPN, 5-32 Amps, 240 volts, breaking capacity 10KA complete all as spcified and as directed.

S & F MCB TPN 40-100 Amps, 240 volts, breaking capacity 10KA complete all as spcified and as directed.

S&F in of sheet metal enclosures with socket, plug top complete with one single pole MCB -240 Volt- 20 AMP complete all as spcified and as directed.

Supply and fix electric bell (ding dong) 230Volts single pole complete all as spcified and as directed.

Supply and fix Modular switch 2 way 6A,1 module complete all as spcified and as directed.

M&L for Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with earthing lead of 4mm dia galvanised iron or steel wire protected by provision of GI mediumgrade pipe 15mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4Kg/Sqm) and frame of angle iron 40x 40x6 mm and handle of 6mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering perforated at bottom, 1.75meter long placed on top edge of earth plate, common salt & charcoal filling with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate No -2 of SSR 2009 Part-I and connecting to Lighting protection earth test points complete all as spcified and as directed.

Supply & Laying & commissining of LT UG cable XLPE sheathed PVC insulated, screened PVC bedded, galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volts grade, laid in tranches, in GI pipe, including brass cable glands, clamps etc of size 4 core x 25 Sqmm complete all as specifed and as directed. Note: Earthwork, sand cushioning, bricks, GI pipe, etc will be measured and pad under appropriate items.

Supply and Laying Double wall corrugated pipe(DWC pipe, Specification-120 mm OD/103 mm ID) for laying XLPE LT UG cable by DWC pipe throughout the LT cable length in pieces of convenient lenth complete all as specifed and as directed. (Note : in pieces for easy rectification during fault ).

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 100 mm dia suitable for 0.4 mpa working pressure complete all as specifed and as directed.

S&F GI tubing light grade 40mm dia for protection of cable on pole/ wall etc complete all as specifed and as directed.

Supply, laying and jointing GI tubes, medium grade40mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches complete all as specifed and as directed.

Supply, laying and jointing GI tubes, medium grade 25mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches complete all as specifed and as directed.

Supply, laying and jointing GI tubes, medium grade 20mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in walls/under floors complete all as specifed and as directed.

Supply and fixing Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specifed and as directed.

M&L for Cutting existing steel tubing for alterations or additions done in position without taking down for 10mm to 40 dia pipe (Each cut measured) complete all as specifed and as directed.

S&F Gun metal gate valve 40 mm bore with iron wheel head screwed both ends for iron pipes complete all as specifed and as directed.

S&F Gun metal gate valve 20mm bore with iron wheel head screwed both ends for iron pipes complete all as specifed and as directed.

S&F Gun metal gate valve 15mm bore with iron wheel head screwed both ends for iron pipes complete all as specifed and as directed.

Materal and labour for construction of brick masonary valve pit chamber of size 900x900x600 mm (Internal dimension) using sub class ,B, bricks complete, earth work, PCC (1:4:8) type D-2 using 40 mm graded stone aggregate in foundation, brick masonary sub class bricks 23 cm build n cement mortar and below ground level PCC with 1:2:4 type B2 using 20mm grade stone aggregate, copng 50 mm thick including frame of size 75x75x6mm made of angles iron and chamber cover made of MS sheet of 4 mm thickness double leaf including MS hinges locking arrangement with provision of locks and keys, painting of the steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer including necessary excavation, returning & filling & removing of surplus soil etc complete all as specifed and as directed.

Please Enable Macros to View BoQ information