Restoration of Canteen Building at Tagore Arts and Science College

Amount

Code No. 2.8.1 Earthwork in excavation by mechanical means ydraulic excavator) / manual means in foundation renches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming ofbottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m - all kinds of soil.

Code No. 4.1.10: Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level 1:5:10 (1 cement : 5 sand : 10 graded brick aggregate 40mm nominal size).

Code No. 5.3 Reinforced cement concrete work in beams, suspended floors , roofs having slope up to 15degree landings , balconies , shelves , chajjas , lintels , bands , plain window sills , staircases and spiral stair cases upto floor five level excluing the cost of centering ,shuttering, finishing and reinforcement , with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Code No. 5.9.20A Centring and shuttering including strutting , propping etc and removal of form for suspended floors , roofs , landings , baloconies and access platform , with water proof ply 12mm thick and casurina posts

Code No. 5.16 Providing , hoisting and fixing upto floor five level precast reinforced cement concrete in shelves including setting incement mortar 1:3 (1 cement : 3 coarse sand) , cost of required centering , shuttering and finishing with neat cement punning on exposed surfaces but excluding the cost of reinforcement , with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size)

Code No. 5.22A.7 Steel reinforcement for R.C.C.work including straightening , cutting , bending, placing in position and binding all complete above plinth level - Thermo -Mechanically Treated bars (ISI BRAND OF APPROVED MAKE) Fe - 415 or more.

Code No. 6.1.2 Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5 in foundation and plinth in - cement mortar 1:6 (1 cement : 6 coarse sand)

Code No 9.1.2V Providing wood work in frames of doors , windows, clerestory windows and other frames , wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) -Vengai wood

Code No 9.21.1 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part 1) non - decorative type, core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both aces of shutters - 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Code No 9.48.2 Providing and fixing M.S.grills of required pattern in frames of windows etc with M.S. flats , square or round bars etc. including priming coat with approved steel primer all complete - Fixed to openings / wooden frames with rawl plugs screws etc.

Code No 9.53 Providing 40 X 5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bots, nuts and wooden plugs and embeddings in cement concrete block 30 x10 x 15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Code No. 9.70.3 Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc.complete - 75 x 47 x 1.80mm.

Code No. 9.96.1 Providing and fixing aluminium sliding door bolts , ISI marked , anodised ( anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade , with nuts and screws etc complete - 300 X 16 mm.

Code No 9.97.2 Providing and fixing aluminium tower bolts , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS :1868) , transparent or dyed to required colour or shade , with necessary screws etc. complete - 250 x10 mm.

Code No 9.100.1 Providing and fixing aluminium handles , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade,with necessary screws etc, complete - 125 mm

Code No 9.122.1 Providing and fixing to existing door frames - 30mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture , made with fire - retardant grade unsaturated polyester resin , moulded to 3 mm thick FRP laminate for forming hollow rails and styles , with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings , cast monolithically with 5 mm thick FRP laminate for panels conforming to IS : 14856 , including fixing to frames.

Code No. 9.147A.2 Providing and fixing factory made uPVC white colour casement /casement cum fixed glazed windows comprising of uPVC multi-chambered frame , sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 + or - 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension , EPDM gasket , stainless steel (SS 304 grade) friction hinges , zinc alloy (white powder coated) casement handles, G.I fasteners 100 x8 mm size for fixing frame to finished wall , plastic packers , plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality , all complete as per approved drawing.(Single / double glass panes and silicon sealent shall be paid separately) -Casement window double panels with S.S. friction hinges (300 x 19 x 1.9 mm ) made of (small series) frame 47 x 50 mm , sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 + or - 0.2 mm and single glazing bead of appropriate dimension. (Area of window above 0.75 sqm upto 1.50 sqm) - casement window size 1.00x1.35 m

Code No 9.165.1A Providing and fixing of 65mm Godrej Navatal lock of 6 levers etc complete.

Code No 10.25.2 Steel work welded in built up sections / framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets,gates and similar works.

Code No 11.3.1 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc complete - 40mm thick with 20mm nominal size stone aggregate.

Code No 11.36E Providing and fixing commercial quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) , of approved make (Jhonson / Asian / Somany / Nitco) in all colours , shades of size 300 x 450 mm as approved in skirting , risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 300x450 mm.

Code No 12.20L Lime concrete terracing on roofs of required thickness laid to fall with 25mm nominal size brick aggregate and 50% lime mortar 1:2 (1 lime putty : 2 surkhi) rammed and finished with gur and belgiri treatment complete including rounding of junctions with Parapet wall complete.

Code No 12.41.2 Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, (i) Single socketed pipes - 110 mm diameter

Code No 12.42.5.2 Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - bend 87.5 degree - 110 mm bend

Code No. 12.42.6.2 Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gapfor thermal expansion - shoe (plain) - 110mm shoe

Code No. 12.43.2 Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50mm hard wood plugs , screwed with M.S. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc., complete - 110mm.

Code No. 12.44 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm diameter and weighing not less than 440 grams

Code No. 13.2.2 15mm cement plaster on the rough side of single or half brick wall of mix - 1:6 (1cement : 6 fine sand).

Code No. 13.17: 6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat.

Code No. 13.26B Providing and applying white cement based primer (JK primaxx two or more coats) undercoat for exterior cementitious surface.

Code No. 13.44.1 Finishing walls with water proofing cement paint of required shade - New work (Two or more coats applied @ 3.84 kg / 10 sqm)

Code No. 13.50.1 Applying priming coat - with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood).

Code No. 13.50.3 Applying priming coat - with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron / steel works.

Code No. 13.60.1C Wall painting with plastic emulsion paint - Commercial of approved brand and manufacture to give an even shade - two or more coats on new work.

Code No. 13.61.1 Painting with synthetic enamel paint of approved brand and manufacutre to give an even shade - Two or more coats on new work

Code No. 14.17 Raking out joints in lime or cement mortar and preparing the surface for repointing or replastering , including disposal of rubbish to the dumping ground within 50metres lead.

Code No. 14.18.1 Flush pointing with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement for flat tile bricks on top of mud phaska - with F.P.S. brick tiles.

Code No. 14.42.2 White washing with lime to give an even shade - Old work (one or more coats).

Code No. 14.43 Removing white or colour wash by scrapping and sand papering and preparing the surfacesmooth including necessary repairs to scrarches etc.complete.

Code No. 14.82 Dismantling W.C.Pan of all sizes including disposal of dismantled materials i/c malba all complete.

Code No. 15.3 Demolishing R.C.C work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead.

Code No. 15.12.1 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead - of area 3 sqm and below.

Code No. 15.23.1 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead - for thickness of tiles 10mm to 25mm

Code No. 15.56 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Code No. 16.2.1 Making plinth protection with bricks of class designation 3.5 laid on edge in cement mortar 1:6 (1 cement : 6 coarse sand) with 12 mm thick bed of cement mortar 1:6 ( 1 cement : 6 coarse sand) over 75 mm bed of dry brick aggregate 40mm nominal size rammed. Consolidated and grouted with fine sand and the top of bricks pointed with cement mortar 1:3 (1 cement : 3 fine sand).

Code No. 16.90 Poilising the existing mosaic floor with Power polisher to a high degree of polish as to be perfectely smooth.

Code No. 17.7.2 Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps ,32 mm C.P.brass waste of standard pattern , including painting of fittings and brackets, cutting and making good the walls wherever required - white Vitreous China wash basin size 630x450 mm with a single 15 mm C.P.brass pillar taps.

Code No. 17.10.2.1 Providing and fixing Stainless steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I.brackets and stainless steel plug 40mm , includin painting of fittings and brackets, cutting and making good the walls wherever required - kitchen sink without drain board - 610x510 mm bowl depth 200mm.

Code No. 17.28.1.1 Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete - semi rigid pipe - 32mm dia.

Code No. 17.60.1.2 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors - 100mm inlet and 100mm outlet - sand cast iron S&S as per IS: 1729.

Code No. 17.69.2 Providing and fixing PTMT waste coupling for wash basin and sink, of approved quality and colour - waste coupling 38 mm dia of 83 mm length and 77 mm breadth weighing not less than 60 gms.

Code No. 18.9.31 Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings this included jointing of pipes & fittings with one step ASTM solvent cement , trenching refilling & testing of joints complete (External work) - 20 mm nominal outer dia pipes.

Code No. 18.9.33 Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings this included jointing of pipes & fittings with one step ASTM solvent cement, trenching refilling & testing of joints complete (External work) - 32 mm nominal outer dia pipes.

Code No. 18.15.1 Providing and fixing brass bib cock of approved quality - 15mm nominal bore.

Code No. 18.17.1A Providing and fixing gun metal gate valve with C.I.wheel of approved quality (screwed end) - 20 mm nominal bore.

Code No. 18.17.3 Providing and fixing gun metal gate valve with C.I.wheel of approved quality (Screwed end) - 40mm nominal bore.

Code No. 18.21.2.1 Providing and fixing unplasticised PVC connection pipe with brass unions - 45 cm length - 15mm nominal bore.

Code No. 18.53.1 Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931- 15 mm nominal bore.

Code No. 19.7.1.1 Constructing brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), foundtion concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design - inside size 90x80 cm and 45 cm deep including C.I.cover with frame (light duty) 455 X 610 mm internal dimensions , total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) - with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5.

Code No. 19.20 Supplying and fixing C.I.cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 kg.

Code No. 19.32.1 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diametre , 1.8 m long complete as per standard design - with common burnt clay F.P.S. (non modular) bricks of class designation 3.5.

Code No. 19.33.1 Providing and fixing on wall / column face unplasticed - PVC soil and waste pipes (type - B) conforming to IS : 13592- 1992 including jointing with seal ring conformation to IS : 5382 leaving 10mm gap for thermal expansion - single socked pipes -110mm diametre.

Code No. 19.33.1B Providing and fixing on wall face / column face unplasticised - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 - 1999 including jointing with seal ring conforming to IS :5382 leaving 10mm gap for thermal expansion - Single tee without door - 110 x110x110mm.

Code No. 19.33.1C Providing and fixing on wall face / column face unplasticised - PVC mould fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend 110 mm.

Code No. 19.33.2 Providing and fixing on wall / column face unplasticised - PVC soil and waste pipes (type B) conforming to IS :13592 - 1992 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single socketed pipes 75mm diameter.

Code No.19.33.2B Providing and fixing on wall / column face unplasticisd - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single tee without door - 75x75x75mm.

Code No. 19.33.2C Providing and fixing on wall / column face unplasticisd - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Bend 75 mm.

M.THIRUGNANAM CONSTRUCTIONS