Interior works for the development of Executive cum office lounge at 3rd and 4th floor of IIIDEM (ECI) building, sec- 13, Dwarka, New Delhi

Grand Total DSR + Non DSR 8,355,898.28

Providing and laying in position cement concrete of specified grade exluding the cost of centring and

shuttering-all work upto plinth level.

4.1.8 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) 3 Cum 6326.05 18978.15

Demolishing brick work manually/ by mechanical means including stacking of serviceable material

and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

15.7.4 In cement mortar 1 Cum 1698.45 1698.45

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50

15.23.1 For thickness of tiles 10 mm to 25 mm 100 Sqm 60.50 6050.00

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of

serviceable materials and disposal of unserviceable materials within 50 metres lead.

Total Concrete Work and demolishing work 31376.60 0.00

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) 10 Sqm 1018.05 10180.50

Total Brick Work 10180.50 0.00

3 FINISHING WORK

3.01 13.4 12 mm cement plaster of mix :

13.4.1 1:4 (1 cement: 4 coarse sand) 20 Sqm 307.25 6145.00

3.02 13.60 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

3.03 13.61 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Total Finishing Work 21244.50 0.00

4 WATERPROOFING WORK

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions

of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed

with water proofing compound conforming to IS 2645 in recommended proportions including rounding off

junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3

4.01 22.3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off 10 Sqm 774.25 7742.50

junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied

hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of

PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Total Water proofing Work 7742.50 0.00

5 DOOR,WINDOW & PARTITION

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought

5.01 9.1 framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast

lugs or dash fastener shall be paid for separately).

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,

core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply

5.02 9.21 veneering with vertical grains or cross bands and face veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 10 Sqm 2015.75 20157.50

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush

door shutters (over all area of door shutter to be measured).

Providing and fixing Stainless steel satin finish SS 304 grade Sliding Door bolts 250x16 mm for wooden

5.04 MR doors of approved make and model all complete as per the directions of Engineer-in-charge 4 Each 1740.00 6960.00

Providing and fixing Stainless steel satin finish SS 304 grade Tower Bolts SS screws for wooden doors

5.05 MR of approved make and model all complete as per the directions of Engineer-in-charge 4 Each 535.00 2140.00

Providing and fixing Stainless steel satin finish SS 304 grade Handles with SS screws for wooden doors

5.06 MR of approved make and model all complete as per the directions of Engineer-in-charge 4 Each 1930.00 7720.00

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand

5.07 9.83 logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), 4 Each 1025.65 4102.60

with necessary accessories and screws etc. complete.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts,

5.08 9.53 nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 16 Each 194.35 3109.60

coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and

manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type

5.10 21.18 fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per 50 Sqm 4540.70 227035.00

direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with

5.11 SS screws etc .complete as per direction of Engineer-in-Charge.

21.12.2 Powder coated minimum thickness 50 micron aluminium tubular handle bar 4 Each 563.50 2254.00

Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to

reproduce Sand-blasting effect on glass with customised designs, thickness of 2 mil (0.05mm) without

adhesive & 3mil (0.8)with adhesive having minimum tensile strength of 3.5 pound/inch at 73 F(0.6 kg/cm

5.12 MR at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic, Glass 25 Sqm 2563.00 64075.00

Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to 15yrs (indoors) must be endorsed

by 3M India Limited Architectural Market Department. Contractors payment wouldn't be released until &

unless he/she produces orginal warranty certificate from the manufacturer.

Total Door, Window & Glass Partition Work 84744.13 310184.00

6 PARTITION WORK

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved

6.01 9.140 primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in

9.140.1 12mm thick MDF Board 150 Sqm 1084.6 162690.00

Providing and fixing metal system up to ceiling height, which includes frame work made of special

section power pressed/ roll form G.I. sheet with zinc coating of 120 GSM, consisting of Boral U track

52mm wide having equal flanges of 30mm and 0.55mm thick (Base metal thickness) fastened to the

floor slab and ceiling soffit using rawl plugs with screw at 600mm centers, with first & last fixing point at

6.02 MR not greater than 50 mm from either end. Boral C studs 50mm wide having one flange of 34mm, other 150 Sqm 743.00 111450.00

flange 36mm, lip size 6 mm and 0.55mm thick installed perpendicularly within the flanges of floor and

ceiling channels located directly opposite to each other at not more than 610mm centers. Maintain 5 to

10mm gap between C Stud and web of U Track.

Total Partition Work 0.00 274140.00

7 FLOORING WORK

Panel 1820 x 145 Total thickness 14 mm Numbers of panels per pack 6 Nested Lengths Max. 1 plank

out of 6 m2 per pack 1,583 m2 Kg per pack 11,99 kg Toplayer PEFC controlled sources EN 13489 ± 3

mm Core board PEFC controlled sources Spruce Backing layer PEFC controlled sources Wood Veneer

2 mm Tongue and groove Length Uniclic Width Uniclic Multifit Domestic use Conditions in each pack 33

years Uniclic - Multifit connection Lifetime Commercial On request "Wood for Life" Edge Protect +

Provides a warranty on build-up of residue dirt along the edges due to maintenance over the years 10

years "Wood for Life" Surface & Edge Protect + (lacquered products only) Provides a warranty on

pollution of surface structure and a warranty on build-up residue dirt along the edges due to

maintenance over the years 10 years Surface layer Wood species Oak Origin Europe Finishing UV

cured Oiled finish 2 layers UV cured Lacquer Anti-scratch top coat 5 - 7 layers Natural variance Due to

nature, visual surface can deviate from samples Surface treatments cf catalogue/website Nature

Marquant Vibrant General aspect of installed EN 13489 Lipping - difference in height (mm) ≤ 0,20

difference in width (mm) ≤ 0,20 cupping lengthwise % ≤ 0,1 cupping in width % ≤ 0,2 Dimensional

stability ISO 24339 Cupping short side max % ≤ 0,30 Changes 30 - 85 % RH Cupping short side min %

≥ - 0,20 Open joints short side (mm) ≤ 0,20 Open joints long side (mm) ≤ 0,30 Underfloor heating

Suitable of special installation instructions.

Providing and laying decorative vitrified floor tiles in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in

7.02 11.41 all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with

grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments

etc., complete.

11.41A Size of Tile 1200x600 mm

Total Flooring Work 40318.75 1500606.00

8 FALSE CEILING WORK

Providing and fixing GI Plain 75mm wide x15mm deep panel upto 6mtr, shall be roll formed out of

0.5mm thick Powder Coated .The top coat of panel shall be 60 micron polyester coated finish in

approved colour. The panel shall be factory cut in up to 6Mtr OR required length. Accessories Detail:

8.01 MR Carrier: 63mm deep, made out of 0.6mm thick steel backed with enameled black paint having cut out to 10 Sqm 3652.00 36520.00

hold on panel in a module of 75mm closed. The joint of two carriers shall be joined by means of carrier

splices maintaining a module of 75mm .4mm dia galvanized rod with special height adjustment butter fly

clips made out of SS steel sheet. The edge profile G.I.shall be matching with the panel.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of

special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm

(both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick

with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash

fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of

25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed

with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to

which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each

having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every

junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30

mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs

at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board

to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm

c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with

recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering

upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's

specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts

made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and

direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS

certification marks)

Providing and Fixing and Installation of Trap Door of Single Leaf with all necessary hardwares as per

Interior Design and the direction of Engineer-in-charge

Total Ceiling Work 185643.90 87770.00

9 WALL FINISHES

Providing and fixing of 6 mm thick premium GRIHA rated Lacquered glass of approved color by

Architect/ Client / Customer, fixed with compatible neutral grade silicon on a perfectly levelled 12mm

thick water proof marine plywood / MDF / Mineral fibre board which is mounted on RCC wall/any other

structure. Lacquered glass must be made industrially (using curtain coating process); opaque (if viewed

9.01 MR against a support wall), uniformly coated with PU lacquer (50 micron thick coating or more); panel to 10 Sqm 4713.00 47130.00

panel colour consistency (measured by photo spectrometer); highly durable (passes hardness test for

minimum 220 oscillations); humidity resistance (conforms to BS EN 1036 1999 or equivalent) ;

environmentally friendly having Low VOC (no lead, no arsenic, no copper, no formaldehyde), low VOC

content <100g/l. Silicone used should not react with lacquer coating (compatible neutral cure silicon)

Providing and fixing 4mm thick coir veneer board, ISI marked IS : 14842, plain lining with necessary

screws, priming coat on unexposed surface etc., complete.

Customised Wall Panel - Plain; designed(400mm X 600mm); Supply , Testing and Commisioning of

9.03 MR maintainance free Moss Wall of size 600 x 400 mm panel of natural light green color/ shade.The plant 10 Sqm 37391.00 373910.00

shall be for indoor use only and requires no Direct Sun Light or Watering / Spraying of water.

Providing & Fixing Vinyl Coated Wall covering as per approved make and pattern as approved by the

client & architect.

Providing & supplying of Window Blinds as per the approved sample in required shade and style

consisting, of Roller Blinds comprising of optima screen Fabric comprising of 22% polyester, 78% PVC,

Fabric weight 460-480G weight per sqm, Thickness 0.67 mm, Yarn count 18-19/cm, having fire

resistance standard – NFPA 701-89 small testing ISO-5659-2 .The tear resistance should be complying

to ISO4674 & breaking resistance – ISO 5081. The DRIVE UNIT shall be of clutch for quick, easy and

safe installation, molded plastic with steel spring support and inserted into the tube end. It shall be

driven by a ball chain pulley with ball chain and can be positioned at right side or left hand side of the

Shade. The Shade when lowering or raising, shall be automatically locked in position upon release of

the ball chain by means of a built in friction lock. Universal clutch for left and right hand operation. Chain

Gear Ratio of 1.75:1.The END PLUG shall be molded of plastic with a steel location pin. The plug shall

9.05 MR be inserted into the tube end. (Opposite to the Drive Unit) for ease of installation. The SUPPORT 10 Sqm 2623.00 26230.00

BRACKETS shall be of coated steel & provided with covers and used in right hand or left hand positions

differentiated by the acceptance of the of the rectangular drive unit support or the round idler plug pin.

Can be installed (a) On Face (b) Ceiling Mount (c) On Frame (d) in Recess. The Bracket should be

protruding outside maximum of 80mm.The ROLLER TUBE shall be of extruded aluminum with 37mm

internal diameter & skin thickness of 1mm and shall incorporate a keyway integral with the tube to

accommodate the spline. The BOTTOM RAIL shall be a Flat Bottom made up

of powder coated steel. The BALLCHAIN shall be 2mm diameter cord with 4.5mm diameter acetal balls

molded co-axially to it on 6mm pitch to form an endless ball chain. It is used for raising or lowering action

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and

9.06 9.40 priming coat on unexposed surface etc. complete :

Kiln seasoned and chemically treated hollock wood 50x12 mm

Kiln seasoned and chemically treated hollock wood 50x20 mm

WOODEN MOULDING- Providing and fixing wooden moulded corner beading of triangular shape to the

9.08 MR junction of panelling etc. with iron screws, plugs etc. complete MDF Finished 12x25mm (base and 10 Metre 104.00 1040.00

Total Wall Finishes Work 235826.50 462110.00

10 Miscellaneous Work

Modular kitchen - Under counter storage cabinets:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with

openable shutters and sufficient number of drawers made of 18 mm thk. ISI Marked comm. ply , all ply

to be laminated with 0.8 mm laminate.All shelves should be supported on approved quality SS pins and

shall be adjustable for different heights as per requirements.Shutters and drawers fascia shall be at least

18mm thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters

finished in high gloss acrylic of approved make- Rehau,Ornare,Senosan. The cabinet boxes of floor

units will be supported by 100mm height vertical adjustable legs (Hettich make) which will be covered

with PVC skirting (Rehau or equivalent make ) in brushed aluminum finish attached by hardware of

skirting. The unit shall be fixed to the floor/ wall/slab using metal screws of appropriate size and rawl

plugs. Only front face area of cabinets and skirting from floor to top of boxes shall be considered for

measurement and payment. Cabinet boxes size would be varies from 400X560X710MM to

1000X560X710MM (approx.) and join together as per site requirements etc.

Modular Kitchen - Overhead storage wall units:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with

openable shutters and sufficient number of drawers made of 18 mm thk. ISI Marked comm. ply . all ply

to be laminated with 0.8 mm laminate.All shelves should be supported on approved quality SS pins and

shall be adjustable for different heights as per requirements.Shutters and drawers fascia shall be at least

18mm thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters

finished in high gloss acrylic of approved make- Rehau,Ornare,Senosan. The unit shall be fixed to the

floor/ wall/slab using metal screws of appropriate size and raw plugs. Only front face area of cabinets

and skirting from floor to top of boxes shall be considered for measurement and payment. Cabinet

boxes size would be varies from 400X560X710MM to 1000X560X710MM (approx.) and join together as

per site requirements etc.

10.03 MR Providing and fixing of Innotech with metal sides and quadro channels .Make.Hettich,Samsung,Inox 2 Each 7011.00 14022.00

10.04 MR Providing and fixing baskets .Make.Hettich,Samsung,Inox 2 Each 8903.00 17806.00

10.05 MR Providing making and fixing in position custom made SS siganges of sizes 16"x5"as per Architectural

drawings and instruction with approved SS fixtures, approved base including necessary hardware, 4 Nos. 890.00 3560.00

substructure extra complete as per detail drawing, as specified and directed by Engineer in charge

Total Miscellaneous Work 0.00 248173.00

Poviding and fixing Digital printed Replica of selected painiting (art work) on Canvas, mounted over

canvass frame, and to be hung to partition with suitable accessiories and complete in all respects

1panel 45” x 45”- Digital Prints 5 Sq m 11250.00 56250.00

Total ART Work 0.00 56250.00

12 Horticulture and Landscaping

DSRH- Supply and Planting Monstera plant having 3-4 ft height complete.

12.02 MR Supply and Planting Lolina plant having 2-3 ft height with Coco-peat, mud and manure complete. 5 Each 1941.00 9705.00

DSRH- Supply and Planting Seaforthia Palm having ht. 90cm to 1.20 m with 6-8 suckers, well developed, fresh

3.82 and healthy lush green leaves from bottom to top complete.

DSRH- Supply and Planting Rhapis Palm having ht. 90cm to 1.20 m with 15 to 18 equal suckers, well

3.77 developed, full of fresh and healthy leaves from bottom to top complete.

Supply of double layered translucent backlit cylinderical shaped - hand carfted pattern planters of make

sereno, model no: chiara 60; volume 18 ltr; approx. dimension 24(h)x18(d) in granite/ stone/ solid finish

or equivalent. planters to be indigenously made by rotational moulding, with homogeneous 100%

recyclable, industrial grade polymer-resin mix, with textured surface and stone match finishes. planters

12.05 MR to have concealed shock resistant back lighting system with secured supply wire and an integrated 5 Each 14488.00 72440.00

water outlet hole & plug, peel proof construction, asbestos free, light in weight, without any joints, rust

proof, uv stabilized, anti-frost feature and easy to clean. planter supplier must give 1 year warranty

against any led, fading or cracking for indoor and outdoor use.

Supply of double layered translucent backlit cylinderical shaped - hand carfted pattern planters of make

sereno, model no: chiara slim 100; volume 40 ltr; approx. dimension 40(h)x18.5(d) in granite/ stone/

solid finish or equivalent. planters to be indigenously made by rotational moulding, with homogeneous

100% recyclable, industrial grade polymer-resin mix, with textured surface and stone match finishes.

12.06 MR planters to have concealed shock resistant back lighting system with secured supply wire and an 5 Each 22901.00 114505.00

integrated water outlet hole & plug, peel proof construction, asbestos free, light in weight, without any

joints, rust proof, uv stabilized, anti-frost feature and easy to clean. planter supplier must give 1 year

warranty against any led, fading or cracking for indoor and outdoor use.

Total Horticulture and Landscaping Work 4817.75 196650.00

GRAND TOTAL 3757778.13

GRAND TOTAL 3757778.13

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR/ MR S.NO. DESCRIPTION UNIT RATE TOTAL AMOUNT TOTAL AMOUNT

DSR/ MR S.NO. DESCRIPTION UNIT RATE TOTAL AMOUNT TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

Supply, Installation, Testing and Commisioning of SINGLE LEVER CONCEALED BASIN

MIXER (WALL MOUNTED) WITH SPOUT (COMPOSITE ONE PIECE BODY)

Supply, Installation, Testing and Commisioning of TABLE TOP BASIN

SIZE: 630x460x130mm

Supply, Installation, Testing and Commisioing of suitable compatible WASTE COUPLING

32MM- FULL THREAD- WITH CERAMIC CAP-*130MM HEIGHT *65MM CERAMIC CAP

Supply, Installation, Testing and Commisioing of BOTTLE TRAP (WITH INTERNAL

MR 4 PARTITION) 32mm SIZE WITH 300mm & 190mm LONG WALL CONNECTION PIPES & EACH 2 1432.00 2864.00

Supply, Installation, Testing and Commisiong of RIMLESS, BLIND INSTALLATION WALL

MR 5 HUNG WC WITH UF SOFT CLOSE SLIM SEAT COVER, HINGES AND ACCESSORIES EACH 2 10514.00 21028.00

SET, SIZE: 375X520X400 MM

MR 6 Supply, Installation, Testing and Commisiong of CONCEALED CISTERN EACH 2 5387.00 10774.00

Supply, Installation, Testing and Commisiong of ANGULAR STOP COCK WITH WALL

Supply, Installation, Testing and Commisiong of CONCEALED STOP COCK WITH

ADJUSTABLE WITH WALL FLANGE 15mm

Supply, Installation, Testing and Commisiong of HAND SHOWER (HEALTH FAUCET) WITH

8mm DIA 1.2 METER LONG FLEXIBLE TUBE AND WALL HOOK ALD-CHR-573 or

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I.

17.10 brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting

10 and making good the walls wherever required :

17.10.1 Kitchen Sink with Drain Board

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings

17.28 complete.

17.28.2 Flexible pipe

Providing and fixing mirror of superior glass (of approved quality) complete with 6 mm thick Each 2 1411.15 2822.30

hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

17.34 Providing and fixing toilet paper holder

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved

14 quality conforming to IS : 8931

18.53.1 15 mm nominal bore Each 5 500.35 2501.75

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast

(spun) iron pipes and making good the same with cement concrete 1:3:6 (1 cement: 3 coarse

17.61 sand: 6 graded stone aggregate 12.5 mm nominal size) including necessary plaster and

pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :

18.76 Cutting holes upto 30 X 30 cm in walls including making good the same.

18.76.1 With common burnt clay F.P.S. (non modular) bricks Each 3 362.40 1087.20

Making chases upto 7.5 X 7.5 cm in walls including making good and finishing with matching M 5 171.80 859.00

surface after housing G.I. pipe etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for

hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the

18.7 pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step

CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

18 20mm nominal outer dia pipes M 5 325.10 1625.50

18.7.3 25mm nominal outer dia pipes M 5 408.55 2042.75

18.7.4 32mm nominal outer dia pipes M 5 500.95 2504.75

18.7.5 40mm nominal outer dia pipes M 5 674.35 3371.75

18.7.6 50mm nominal outer dia pipes M 5 927.00 4635.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for

hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe

with clamps at 1.00 m spacing.

18.8 This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of

cutting chases and making good the same including testing of joints complete as per direction

of Engineer in Charge.

Concealed work including cutting chases and making good the walls etc.,

18.8.1 15mm nominal outer dia pipes M 5 441.15 2205.75

18.8.2 20mm nominal outer dia pipes M 5 513.75 2568.75

18.8.3 25mm nominal outer dia pipes M 5 626.05 3130.25

18.8.4 32mm nominal outer dia pipes M 5 712.75 3563.75

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS

20 standards and weighing not less than 690 gms.

18.51.1 15 mm nominal bore Each 5 708.40 3542.00

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for

soil, waste, and vent, Type-B as per IS : 13592 suitable for rubber ring joints, including all

neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or

without doors), reducers, WC connectors, couplers, expansion joints / bellows, cowels,

clamps, rubber rings, clean outs etc. fixing at wall/ ceiling/ floor level supported by clamp &

hangers etc. in concealed / inside duct / under floor & basement ceiling / external work etc.

including chase cutting as required, excavation and back filling in all kind of soils, suspended

from floor under false ceiling or embedding the pipes laid under floors / building in 75 mm.

MR alround 1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

21.0 nominal size) including cost of shuttering for proper completion of the work, breaking and

making good the walls and floors etc. after pipes have been duly laid and tested. The rubber

ring shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with nuts, washers etc on

50x50x5 mm slotted angle. The cost will include all support arrangements. The work includes

commissioning of all pipes lines as per drawings and specifications and as directed by engg-

in-charge at site.

MR 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) metre 110.00 344.00 37840.00

MR 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) metre 5.00 344.00 1720.00

Providing, fixing, jointing and testing in position ISI marked (IS:4985) UPVC pipes of min 6

Kg/ Sqcm rating with fitting for waste pipe from fixtures to floor trap including reduces,

enlarger, socket, couplers, bends, tees etc including fixing at wall/ ceiling level supported by

clamp & hangers etc. cutting holes in wall/ floors/ slabs and making good the same with

cement concrete 1:2:4 complete as required.

Providing & fixing UPVC Floor trap of self cleansing design with stainless steel grating

MR 23 complete in all respects.

Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser each 4 330.00 1320.00

MR 24 Extra for providing & fixing 125 mm dia C.P. grating in place of C.I. grating over floor traps. each 4 673.00 2692.00

Providing & fixing of SS Floor Cleanout, round or square with rubber seal and flat round

cover with screws and other required fitting complete as required. each 4 537.00

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S No DSR/ MR DESCRIPTION UNIT RATE TOTAL AMOUNT TOTAL AMOUNT

S No DSR/ MR DESCRIPTION UNIT RATE TOTAL AMOUNT TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface / recessed medium class PVC

A.1 1.1 conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5

sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point (without independent

switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in

A.2 1.55 surface / recessed PVC conduit, and earthing the point with 1.5 sq.mm. FRLS PVC insulated

copper conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single

A.3 1.5 core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq mm FRLS Metre 500 265 132500

PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single

A.4 1.6 core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos 4 sq. mm FRLS Metre 50 392 19600

PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch

A.5 1.24 box including connections but excluding modular plate etc. as required.

1.24.1 5/6 amps switch Each 32 85 2720

1.24.4 3 pin 5/6 amp socket outlet Each 32 111 3552

1.24.5 6 pin 15/16 amp socket outlet Each 10 175 1750

1.24.6 telephone socket outlet Each 4 119 476

1.24.7 TV antenna socket outlet Each 4 119 476

1.24.8 Bell Push Each 2 126 252

MR USB Each 2 253 506

Supplying and fixing following size/module, GI box along with Modular base & cover plate on

A.6 1.27 existing modular metal boxes etc. as required.

1.27.1 1 or 2 Module Each 2 243 486

Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper

A.7 1.15 conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit

including dismantling as required.

1.15.2 Group B Point 2 447 894

Dismantling of ceiling fan and painting the same with with one or more coats of spray painting

with synthetic enamel paint of approved brand and manufacture to give an even shade,

A.8 1.59 including cleaning of surface with detergent and replacing the damaged rubber reel, nuts and Each 6 221 1326

bolts with washers and safety pins, reinstalling the same as required.

Dismantling of light fixtures existing and installation, testing and commisioning of the existing

A.9 MR light fixture in other rooms including all connections complete in all respect as per the Each 90 187 16830

directions of the engineer in charge

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC

B.1 1.14 insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit

1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre 50 146 7300

1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 10 167 1670

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 10 200 2000

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 10 249 2490

1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 10 543 5430

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 10 752 7520

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit

D.2 2.1 breaker suitable for inductive load of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

2.10.1 Single pole Each 20 199 3980

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB

2.13 complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, vertical type three pole and neutral, sheet steel, MCB

distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral

D.3 2.5 bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as

required. (But without MCB/RCCB/Isolator)

2.5.2 8 way (4 + 24), Double door Each 2 7744 15488

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts,

D.5 2.14 residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in

the existing MCB DB complete with connections, testing and commissioning etc. as required.

LIGHTING FIXTURES & FITTINGS

SITC LED recessed mounted circular downlight with LED Light Emitting Diode for system

power 15W, luminous flux of 1275 lm, CRI> 80, 230V constant current driver, colour

temperature of 4000K neutral white, direct light emission, housing with ceiling trim, in die-cast

1 MR aluminium, polyester powder coat applied over a 5-stage pre-treatment, deep white satin EACH 25 2079 51975

diffuser, passive cooling, electronic control gear, Protection class I , IP 20, Ø = 170, DA(ø) =

Supply, Installation, testing and commsionig of LED strip (flexible) with 60 LEDs per meter,

12W per Meter, 4000K, 2835 SMD package with thermal tape of high thermal convection

2 MR factor, beam angle of 120°, MacAdum 5, constant voltage driving circuit, L = 1000mm, H = MTR 50 1177 58850

10mm, B = 1.4mm, with suitable driver

LED Recessed directional spotlight with LED (Light Emitting Diode) system power: 9W,

luminous flux of luminaire 900lm, 230V constant current driver, 70% of luminous flux after

50,000 operating hours; energy efficient LEDs, colour temperature of 4000K, neutral white,

3 MR direct light emission, narrow beam of 10°, luminaire part adjustable, polyester powder coat Each 10 1940 19400

applied over a 5-stage pre-treatment, electronic control gear, Protection class II, IP20, L =

Supply, Installation, Testing and Commisioning of Semi-Transparent Pendant Light with

Lamp: E-27 LED 14W x 1 of Depth 300mm and Height 1200 mm (Ref: Jaquar Lighting: KCH-

CHR-MD130900011C

Supply, Installation, Testing and Commisioning of Gold Finishing Meta Swan Ceiling with 18

5 MR Arms in Gold finish Light with Lamp: G4 Bulb 20W x 18 of Depth 860 mm and Height 780 mm Each 2 98129 196258

(Ref: Jaquar Lighting:KCH-GLD-MX809818A)

Supply, Installation, Testing and Commisioning of Chrome Finishing Pendant Light with

6 MR Lamp: E-27 LED 9W x 1 of Depth 120 mm and Height 1200 mm (Ref: Jaquar Lighting:KCH- Each 4 3849 15396

CHR-MD150031291A)

Supply, Installation, Testing and Commisioning of Chrome & Rose gold clear glass pendant

7 MR with Lamp: G9 5W x 1 of Depth 195 mm and Height 1200 mm (Ref: Jaquar Lighting: KCH- Each 4 2390 9560

CHR-MD160020051C)

Supply, Installation, Testing and Commisioning of Wooden Base with PVC shade Table Lamp

8 MR with Lamp: E-27 LED 9W x 1 of Depth 400 mm and Height 833 mm (Ref: Jaquar Lighting: Each 4 14604 58416

STL-BLK-TL1093T)

Supply, Installation, Testing and Commisioning of Smoky Glass Pendant with Lamp: E-27

9 MR LED 9W x 1 of Depth 150 mm and Height 1200 mm (Ref: Jaquar Lighting: KCH-CHR- Each 4 3286 13144

Supply, Installation, Testing and Commisioning of Smoky Glass Pendant with Lamp: E-27

10 MR LED 9W x 1 of Depth 220 mm and Height 1200 mm (Ref: Jaquar Lighting: KCH-CHR- Each 4 3153 12612

Supply, Installation, Testing and Commisioning of Wooden Base with PVC Shade Floor Lamp

11 MR with Lamp: E-27 LED 14W x 1 of Depth 580 mm and Height 1830 mm (Ref: Jaquar Lighting: Each 4 36509 146036

STL-BLK-FL1093F)

SCHEDULE OF QUANTITIES - HVAC-VRV-AC WORKS

S. No. DSR/ MR DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

S. No. DSR/ MR DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant

Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating,

having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors

for above 14 HP modules, microprocessor based Controller, top discharge type condensing

unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as

1 1 required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C per HP 16 16415.00 262640.00

ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3

Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and

ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not

less than 6.5 .

Supply,installation,testing and commissioning of following minimum capacity VRV/VRF High

wall type Indoor unit equipped with washable synthetic media pre-filter,fan section with low

noise fan/ dynamically balanced blower, multi speedmotor ,coil section with DX copper coil,

electronic expansion valve, outer cabinet ,cordless remote control,drain pan,necessary

2 3 accessories etc., suitable for operationon 230V±10%, 50Hz, single phase AC supply,complete

as required. The unit shall have automatic force shutdown provision in case of fire on receiving

signal from BMS System.The cooling capacity of indoor unit will be at air inlet conditions of

27Degree C DB and 19 Degree C WB temperature.

Lifting, Shifting, Supply, Installation, Testing & Commissioning of Interconnecting "Y" & "T"

3 MR Joints i.e. Refnet Joints/Header with Insulation for refrigearnt piping

(Make : DAIKIN, TOSHIBA, O GENERAL, MITSUBISHI)

4 5 Refrigerant Piping

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing

of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system,

complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing

including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell

elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for

Suction and Liquid lines, all accessories as per specifications etc. as required :

4.1 5.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 60 245.00 14700.00

4.2 5.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 60 331.00 19860.00

4.3 5.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 60 466.00 27960.00

4.4 5.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 60 588.00 35280.00

4.5 5.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 10 707.00 7070.00

4.6 5.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 10 865.00 8650.00

4.7 5.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 10 1022.00 10220.00

4.8 5.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 10 1108.00 11080.00

5 6 Cable/Wiring

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit

6 7 Cable Trays with Covers

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray

(Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in

convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders

including G.I. bolts & nuts, etc. as required.

6.1 4.6.8 300 mm width X 62.5 mm depth X 2.0 mm thickness meter 20 1085.00 21700.00

7 MR Drain Piping

Supply,installation,testing and commissioning of PVC drain water with necessary clamps,

fittings such as bends tees etc. and duly insulated.

40 mm dia (9 mm tick ins.) Rm 40 374.00 14960.00

INLINE FANS Ostberg make

Supply Installation, Testing and Commissioning of Inline fan suitable for following capacities

complete with sheet metal casing , electric motor and direct driven centrifugal fan suitable for

operation on 415 +/-10% V,50 Hz , 3 phase or 240 +/- 10% V,50 Hz, 1 phasefitted with speed

8 MR regulator in case of single phase including provision of 15 Amp plug and wiring between the

fan and the socket and accessories like flexible connectors , gravity louvers , wire guard & bird

screen etc.The fans shall be acoustically insulated from inside to reduce the db levels. All the

fans used for purging of FM 200 shall be fitted with fire dampers which shall be charged as per

150 CFM,20 MM STATIC PRESSURE Nos 2.0 6775.00 20325.83

Total HVAC WORKS 640924.00 91652.00

SCHEDULE OF QUANTITIES - WIFI & LAN WORKS

QUANTIT TOTAL TOTAL

DSR/ MR SNO. DESCRIPTION UNIT RATE

Y AMOUNT AMOUNT

DSR (INR) NON-DSR

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed (INR)

1 Steel/ PVC conduit as required.

Supplying, installing, testing and commissioning of I/O Jack should be Category 6, TIA568B.2-

1 – 250MHz, I/O Jack should be for 100 W, 22-24 AWG copper cable shall: Use insulation

displacement connectors (IDC), Information outlet (RJ45 jack) should be covered under ETL

M.R. 2 Verification program for compliance with TIA568B.2-1, ETL certificate to be submitted with Nos 12 409.00 4908.00

offer the I/O jack should be Blue colour for easy port identification, Operating Life: Minimum

750 insertion cycle

Supply , Installtion , Testing and comissioning of Cat6 1Meter patch cords Blue colour with

high quality four pair twisted stranded cable terminated with RJ45 tangle free modular plugs

M.R. 3 at both the ends. The Conductor should be 24 AWG, Multi-strands & Bare Copper Conductor Nos 12 263.00 3156.00

Supply , Installtion , Testing and comissioning of Cat6 2 Meter patch cords Blue Colour with

high quality four pair twisted stranded cable terminated with RJ45 tangle free modular plugs

M.R. 4 at both the ends. The Conductor should be 24 AWG, Multi-strands & Bare Copper Conductor Nos 12 279.00 3348.00

Supply , Installtion , Testing and comissioning of Face Plate should be Single Gang square

plate, 86mmx86mm, should have Write on labels, The Faceplates should have inbuilt

M.R. 5 shutters which are compatible with any standard colored keystones jacks. The Faceplates are Nos 4 112.00 448.00

available in one, two and four port variants.

TOTAL WIFI & LAN WORKS 0 23620.00

SCHEDULE OF QUANTITIES: EPABX

TOTAL AMOUNT TOTAL AMOUNT

TOTAL AMOUNT TOTAL AMOUNT

DSR/ MR S NO DESCRIPTION UNIT QUANTITY RATE

DSR (INR) NON-DSR (INR)

M.R. Supply of Type 1 IP Phone . Graphic LCD display with backlight 3

1 user accounts with multi-line appearance keys Local and company- Nos 2.00 18000.00 0 36000

wide phone directories .

M.R. Supply Installation, Testing and Commissioning of Analog Speaker

Phone with backlight.

TOTAL EPABX WORKS 0 40400

SCHEDULE OF QUANTITIES: Display Units

DSR/ MR SNO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

DSR (INR) NON-DSR (INR)

SITC of 55" diplsay panel with IPS technology, 16:9 aspect ratio,

2840 x 2160 (4K) native resolution, 500 nits brithness, 178 x 178

degree viewing angle, hard coating (3H) minimum surface treatment,

M.R. 1 should be anti glare treatment, should be 24 hours operational Nos 4 87223.00 348892.00

hours, should be usable in landscape or protrait modes, should have

atleast 2xHDMI, DP, DVI-D, RGB, Audio, USB 3.0, should have

RS232C in/out, RJ45 In, IR receiver in, pixel sensor in etc all

M.R. 2 SITC of HDMI cables 10 meters M2M etc all compelte . Nos 4 3703.00 14812.00

M.R. 3 SITC of USB cables 10 meters M2M etc all compelte . Nos 2 4165.00 8330.00

SITC of various video cables and connectors of various lengths

M.R. 4 included but not limited to HDMI, VGA + audio as per design Lot 2 32030.00 64060.00

requirements etc all compelte

TOTAL 436094.00

Schedule of Quantities: Furniture

Sr.no Specification Code Third Floor Fourth Floor Total Qty Unit Reference Image

1 Main table for Commissioner Cabin

Main Table Dimension:(L)2400mm X (D)1130mm X (H)770mm

Side Runner Dimension: :(L)1200mm X (D)600mm X (H)770mm

Supplying, and placing in position of table as per photograph. This precise Durian Boss's Desk is

designed with superb qualityFinish made of engineered wood-medium density fibre board &

veneer glossy finish on the same. Functional and stately, with a sturdy design style, this L shape

desk is sure to make a dramatic statement in the office. Featuring a cherry finish, with delicate

panel moulding and a fantastic size.The modesty frame of the table gives the great look with panel

upholstered wth PVC material which gives the leatherette look.Main Table top thkness 80mm ,

side panel/gable end in 70mm thk mdf with venner glossy finish. Main table and side runner

having a skirting @120mm thk with gives a rich look. The office desk comes with the side runner

having enough storage space.The side runner top with a thickness of 80mm thk that gives the

great look . Side table, side panel, shelves,drawers made up of 18mm thk mdf with venner finish.

Table having a provision of Pedestal of size: 400(L) X 500(D) X 660(H) having three drawers to

store essential & undestructure made out of 18mm thk mdf with venner finish .Drawers have the

stylish handle which enhance the look. Material & Subtype:Engineered Wood - Medium Density

Fibre Board, Colour & Colour Family:Red - Cherry.side storage unit having a side panel, one

drawer , one shutter & one shelf of 18mm thk mdf with venner finish. The product should be from

the manufacture of Approved make Godrej/ Durian/ HNI. Complete as per reference image and

specification as mentioned above under the guidance of project architect & Engineer in charge.

2 Back storage for Commissioner Cabin

Dimension:(L)2000mm X (D)450mm X (H)2000mm mod 1 1 2 nos 71578.00 143,156.00

Supplying, and placing in position of back storage as per photograph/drawing. A well-built book

case with the looks this is the complete package. A compartmentalized shelving system with

adequate space ensures any book will fit in the shelf. This Book shelf are made out of 18mm thk

prelam particle board with 2mm thk pvc edge banding .The lower cabinets provisioned with

openable shutters with shelf , D shape handles and locking arrangements and also provisioned

with open storage with shelf in it. The upper area to have open shelves for display. The working

edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue

at hot temperature. The product should be from the manufacture of Approved make Godrej/

Durian/ HNI. Complete as per reference image and specification as mentioned above under the

guidance of project architect & Engineer in charge.

Main chair for Commissioner Cabin

Supplying and placing in position of 360 degrees revolving high back chair as per image. The

Leatherette office chair of size:- (W)655mm X (D)500mm X (H)1230mm is a ergonomic high

back chair made for a business tycoon or a director. The seat is constructed from a combination of

resilient plywood and soft foam for a comfortable seat. The foam cushions are encased in a

chocolate brown leatherette upholstery. The seat arms come padded with foam and are covered in

the same brown upholstery for a relaxed armrest. Powered by a synchro multi locking mechanism

the chair offers you extreme comfort as per your seating position. The office seat is supported by a

shiny chrome base powered by sturdy nylon castors. Function: Revolving::Pneumatic Height

Lift::Tilt Tension Control::Synchro single locking, Base: Chrome Base, Locking Mechanism:

Synchro single locking. The pneumatic height adjustment shall have adjustment stroke of 100mm

and shall be operated at 30kgs extension force. The Seat and back are made up of 12mm thk hot

pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 38-

40 kg/m3 . The backrest has a foam of 28 (+/-2kg /m3 ). The product should be from the

manufacture of Approved make Godrej/ Durian/ HNI. Complete as per reference image and

specification as mentioned above under the guidance of project architect & Engineer in charge

Visitor chair for Commissioner Cabin

Supplying and placing in position of 360 degrees revolving medium back chair as per image. The

Leatherette office chair of size:- (W)555mm X (D)500mm X (H)1105mm is a ergonomic low back

chair made for a business tycoon or a director. The seat is constructed from a combination of

resilient plywood and soft foam for a comfortable seat. The foam cushions are encased in a

chocolate brown leatherette upholstery. The seat arms come padded with foam and are covered in

the same brown upholstery for a relaxed armrest. Powered by a synchro multi locking mechanism

the chair offers you extreme comfort as per your seating position. The office seat is supported by a

shiny chrome base powered by sturdy nylon castors. The pneumatic height adjustment shall have

adjustment stroke of 100mm and shall be operated at 30kgs extension force. The Seat and back

are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam,

chair seat has foam of density 38-40 kg/m3 . The backrest has a foam of 28 (+/-2kg /m3 ). The

product should be from the manufacture of Approved make Godrej/ Durian/ HNI. Complete as

per reference image and specification as mentioned above under the guidance of project architect

& Engineer in charge

5 Sofa for Commissioner lounge area

Three Seator Sofa ((L)1960mm X (D)880mm X (H)760mm) Skyler/3 2 2 4 nos 79314.00 317,256.00

Single Seator Sofa ((L)840mm X (D)880mm X (H)760mm) Skyler/1 8 4 12 nos 44950.00 539,400.00

Supplying and placing in position of sofa as per Image. Its stylish contemporary design boasts a

kiln-dried solid wood frame and rich leather. The magnificent frame slopes from the back to the

seat giving a stately feeling to your seat. High-density foam is upholstered in highly durable

leather providing an exquisitely divine place to unwind. Durian's leather is procured from the

finest Italian tanneries and is stain and fade resistant. Set on sleek stilt legs, the sofa frame has a

unique panel detail that runs onto the cushions as well.Warp and scratch resistant solid wood

frame with Easy to maintain leather upholstery. Fade and stain resistant leather

upholstery.Unique panel detail on the side with sleek stilt legs. Seating Height: 450mm, Legs

Stainless Steel. The product should be from the manufacture of Approved make Godrej/ Durian/

HNI. Complete as per reference image and specification as mentioned above under the guidance

of project architect & Engineer in charge.

6 Centre Table for Commissioner lounge area

Dimension (L)1000mm X (D)1000mm X (H)400mm Cole/ct 3 2 5 nos 45439.00 227,195.00

Supplying, and placing in position of centre Table as per photograph. The Centre table is a

combination of wood and glass for an elegant setting. Table top are made with 12mm Tempered

Glass with Clear Glass Finish. The centre table base are made of Engineered wood fixed to the

Glass top with Warm Wooden Paper Finish. The product should be from the manufacture of

Approved make Godrej/ Durian/ HNI. Complete as per reference image and specification as

mentioned above under the guidance of project architect & Engineer in charge.

Side Table for Commissioner lounge area

Dimension(L)680mm x (W)530mm x (H)460mm Hopper/st 4 8 12 nos 18566.00 222,792.00

Supplying, and placing in position of side table as per Image.The side table made of solid wood

(steam beech) in pu matt polish.The plain glass placed the top of the table in 8mm thk. The glass

table top is made with strong glass and is inlaid onto the solid wood frame. The designer wooden

legs are turned for a sleeker look. The framed edges slope inwards to the table top with defined

edges. Material & Subtype:Solid Wood - Beech Wood ( spc:steam beach), Colour & Colour

Family:Brown - Dark Oak, Legs:Solid Wood, Finish:Glossy, Style:Contemporary. The product

should be from the manufacture of Approved make Godrej/ Durian/ HNI. Complete as per

reference image and specification as mentioned above under the guidance of project architect &

Engineer in charge.

8 Main table for PS Commissioner

Main Table Dimension:(L)1800mm X (D) 900mm X (H) 760mm

Overall Side Runner Dimension: :(L)2220mm X (D)400mm X (H)660mm

Supplying and placing in position of main table as per photograph. The main desk overall size 1800mm

(L) X 2200mm (D) including length of side table X 760mm (H) for main table and 660mm for side unit.

The table top and side panels shall be made out of 70- 80mm thick MDF board including with 0.5mm

laminate with glossy finish and, leatherette attached on table top for extra comfort or looks, laminate

MDF with glossy finish. The desk table top carries a leatherite folio with an inbuilt wire management

system for easy access. Front Modesty panel shall be made out of 09-25mm thick. Provision of one mobile

pedestal with two sliding drawers matching with table top. Coupled with the desk is a movable runner,

having a provision for one shutter either sides, one drawer at bottom side, one key board and one open

shelf for CPU storage. Side unit top shall be made out of 25-30mm thick MDF board including 0.5mm

laminate with glossy finish. The under structure shall be made out of 9-18mm thick 0.5mm laminate with

glossy finish MDF board. Table shall have one separate independent mobile pedestal with two sliding

drawers. Pedestal sides, front and bottom shall be made out of 16mm thick MDF board. Drawers bottom

and backing of the pedestal should be 6-9mm thick MDF board. Pedestal shall have a combination of 2

drawers. Drawers shall be in MDF board with 0.5mm laminate with glossy finish matching with table.

The pedestal shall be movable on lockable castors. . The product should be from the manufacture of

Approved make Godrej/ Durian/ HNI. Complete as per reference image and specification as mentioned

above under the guidance of project architect & Engineer in charge.

9 Main Chair for PS Commissioner 0 1 1 nos 30130.00 30,130.00

Supplying, and placing in position of 360 degree revloving high back chair as per Image.The

premium upholstery is an added touch of extra class. With its supple leather upholstery.

Equipped with a multi-locking knee tilt mechanism and adjustable arms this chair is is high on

back support and comfort.Size: (W)610mm X (D)500mm X (H)1300mm Leather: Semi Aniline

Leather, Function: Revolving::Pneumatic Height Lift::Adjustable Armrest::Multilocking Knee

Tilt, Maximum Seating Height: 24",Minimum Seat Height: 20.86", Base :Chrome Base, Locking

Mechanism: Multi-Locking Knee Tilt.The pneumatic height adjustment shall have adjustment

stroke of 100 mm and shall be operated at 30kgs extension force. The Seat are made up of 12mm

thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of

density 30-32 kg/m3. The product should be from the manufacture of Approved make Godrej/

Durian/ HNI. Complete as per reference image and specification as mentioned above under the

guidance of project architect & Engineer in charge.

TOTAL AMOUNT INCLUDING GST 2,267,366.00

TOTAL AMOUNT INCLUDING GST 2,267,366.00