6290/24-25/01/OPW

Material & Labour for Excavating over areas, n exc1.5 m deep in Hard rock soil and getting out all as specified and as per site requirement.

(Material & Labour for Removing excavated soil to a distance exc 500m but n. exc 1.5 km including loading , unloading into vehicles and depositing where directed including spreading and levelling.

Material & Labour for Returining , filling in including spreading levelling, watering and well ramming in layers each not exc 25 cm thick in soft/loose soil

Material & Labour for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M & L for cement concrete type D2 (1:4:8) (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed by Engr-in-charge.

M & L PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in bond stone (for stone walling ) and set in cm 1:4

M&L for providing SCHB blocks in PD over PCC base in staggered layers filled and compacted with earth use from the excavation

M & L 250 x 125 x 60mm pavers made from proprietary recycled material of Silica Composite Block with compressive strength of 687.1KN and 0,2% water absorption, with tight fit interlocking method over PCC base as mentioned in Item 1, Super Structure. (Drg attached.)

S&F for Factory Made Solid PVC Door Shutter, 28 to 30mm thick(stiles),with 2, 4,or 6raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. along with S&F for Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) complete all as specified and directed. 3 Nos 125mm butt hinges 2 Nos MS tower bolt 200mm long 2 Nos MS bow handle 125mm long two No MS sliding bolt 250mm long all fittings fabricated with steel door and angle iron 40 x 40 x 6mm chowkat frame and shutter frame 35 x 35 x 5 mm including two coat of synthetic enemal paint over one coat of red oxide primer complete all are shown on drg All materials shall conforming to relevant IS

Supply of Swivel Bullet proof glass glass 610mm x330mm size 72 mm thick with fabricated iron frame including necessary locking arrangement in the frame to fix the glass in the loop hole. Bullet Proof Glass Will be made with Raw Glass of ISI Specification duly processed with PVB Interlayer by using Autoclave Process strictly. The bullet proof glass should be uv Resistant 99.1% and follow IS 2553 Norms with Part-2 Transparency 70% minimum. The glass should be capable for safegaurd and should not have perforation against three rounds fire of AK-47 & SLR / Rifle Calibre 7.62 mm from firing range of 10 metres and as per testing norms from Authories Govt Ballistic Testing Laboratory/Institute. The Bullet Proof Glass should not lose it visibility after having hit to first round of fire. Frame Work Made out of 16 gauge steel section for bullet resistant glass will be made rctangular box type for size 122mm x 61mm x 3.60mm (9.67kg/Km) coforming to IS 4923:1987 & glass shutter shall be made of U channel of size 80mm x 40mm x 40mm x 4mm for fixing of glass with rubber bedding. The arrangement of stainless steel Hinges in window to be in centre at top & bottom portion of glass frame to rotate frame in 360 degree. The frame will be painted with two coat of ROMP over one coat of red oxide primer. Hold fast made of flats iron 50x5mm shall be provided both side of frame (02 Nos each side top & bottom) and SS tower bolt shall and other connected accessories be provided.

Supply only (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment welded to the angle frame mounted above and fixed with top beam with nails 2-16# 200long

Steel roofing trough SRT of size 1630 mm x 613 mm x 180 mm made out of 2 mm thick hot rolled carbon steel sheet conforming to relevant IS complete with set of a spanner OJDE of size 20-22 per 10 Nos of SRT SRTs shall be painted with two coats of synthetic enamel paint over a coat of red oxide primer

ISMB 150 (RSJ 150 x 75mm) 3.5 m long conforming to IS 808-1973.

Material & labour for preparation of new surface two coat of nano paint over one coat on primer complete all as specified and directed.

Silicone Gel sealant of 01 pack of 400 gms including applicator gun

HDPE sheet having weight 100 gm/Sqm Black of width 5.50mm Confirming to IS 2508 : 1984

PBS roll (Self finished tarfelt) hessian base (for water proofing) Grade-1 conforming to IS 1322-1980 of size 20m x 0.90 m (weight of each roll shall not be less than 42.50 Kgs + 2.5 Kgs in dry conditions). The finished mtrlsw shall be free from visible external defect such as holes, oil patches, ragged or untrue edges, brakes, cracks, tears, protuberances and indentations.

HDPE Laminated Sand Bag of size 75 x 40 cm

Smart City Solutions India Pvt. Ltd