RequiredOEM Authorization Certificate Bid to RA enabled Yes Track Suits - Sports ( 56 pieces ) ( Under PAC ) Make tyka Model tyka Technical Specifications * As per GeM Category Specification Specification Specification Name Values Bid Requirement (Allowed Values) UTILITY UTILITY Unisex * COMPONENTS Components Complete Set consisting of Upper and Lower * 1/9 MATERIAL Fabric ( Composition ) Polyester Polyester Percentage of Blending ( in case of Blended Fabric ) Polyester 65 % and Viscose 35 % Polyester 65 % and Viscose 35 % Mass ( gram per square mtrs ) 100 100.0 Fabric Construction Woven Woven Weave ( In case of Woven Fabric ) Plain Plain Any other weave as per buyer's requirements ( in case weave is other than already mentioned above ) - * Knitting ( In case of knitted Fabric ) Plain ( Single Jersey ) Knitted
RequiredPlain ( Single Jersey ) Knitted
RequiredEnds per dm - * Picks per dm - * Courses per dm - * Wales per dm - * Count of knitting yarn - * Raising at inner side of Main Fabric Yes Yes Upper Lining Yes Yes Lower Lining Yes Yes Lining Material 100% Polyester Mesh 100% Polyester Mesh Mass of Lining (Gram per Square Meter) 65 * Netting mesh No of holes on base & bias within 625 Square millimeter 155 * Technical Requirements of Slide Fastener for Upper Closing No No Technical Requirements of Slide Fastener for Pocket Closing ( For Pockets with Slide Fastner for closing ) No No Slide Fastners are BIS Marked Not Applicable Not Applicable Width of Tape Elastic at 3.5 cm * 2/9 Waist of Trouser Width of Tape Elastic at Bottom of Upper 3.5 cm * Technical Requirements of Waist Band No No Waist Draw Cord Polypropylene Cord of 4mm dia * Draw Cord Ends Fused * Breaking Strength of Draw Cord 340 N minimum * Sleeve Ends ( Cuff ) Elastic Tape * Upper provided with Piping Yes Yes Lower provided with Piping Yes Yes Piping Fabric- Composition Any other material as per buyer's requirements * Piping Fabric- Any other material as per buyer's requirements ( Other than mentioned above ) - * Piping Fabric Mass ( gram per square mtrs ) 90 90 Embroidery Thread Polyester Polyester SIZE Size Large (L) Large (L) DIMENSIONS OF UPPER Width Across Chest 25 mm below under arm 55.0 cm ( Large ) * Width Across Bottom Opening (relaxed) 48 cm ( Large ) * Length at front from top of collar to bottom 68 cm ( Large ) * Sleeve length (from center of back to bottom of sleeve 87 cm ( Large ) * Sleeve opening relaxed ( Cuff ) Width 10 * Front Neck Drop 9 * Back Neck Drop 1.725 * Length of Slide Fastener 66 cm( Large ) * DIMENSIONS OF LOWER Side Seam Length 107 cm ( Large ) * 3/9 Waist relaxed ( Width Across ) 45.5 cm ( Large ) * Waist stretched (Width Across ) 55 cm ( Large ) * Seat/Hip ( 15 cm below waist band) 55 cm ( Large ) * Thigh (at Crotch) ( Width Across ) 37 cm ( Large ) * Bottom Opening ( Width Across ) 22 * Front rise including waist band 29 cm ( Large ) * Back rise including waist band 39 cm ( Large ) * Length of Waist Tying Cord 160 * Bottom Fold (Hem) with full turn in(cm) 1.5 * POCKETS Number of Pockets (Upper) 2 Side Pockets 2 Side Pockets Size of Side Pockets- Upper ( Length X Width ) ( cm ) 17 cm X 18 cm * Size of Inside Pocket at Chest- Upper 11 cm X 15 cm * Side Pocket opening - Upper 15.0 cm * Side Pocket Closure with Slide Fastener -Upper No No Number of Pockets (Lower) 2 Side Pockets 2 Side Pockets Size of Side Pockets - Lower ( Length X Width ) ( cm ) 17 cm X 18 cm * Side Pocket Opening- Lower 15 * Pocket Closure with Slide Fastener - Lower Side Pockets with Slide Fastener Side Pockets with Slide Fastener Material of Pockets Main Basic Fabric * COLLAR Collar Type Stand and Fall Type
RequiredMade of two layers of self material * Collar Reinforcement With Canvas Reinforcement * 4/9 SLEEVE Sleeve Type Reglan Sleeve * PIPING Position and Dimensions of Piping on Upper - * Position and Dimensions of Piping on Lower - * STITCHING Sewing Thread 145 d tex X 3
RequiredPolyester * Raw edges
Requiredif any shall be bound by overlock stitching Yes * Waist band stitching of Upper Stitched in single rows with chain stitch on the elastic * Sleeve Bottom (Cuff ) Stitching Stitched in single rows with chain stitch on the elastic * Waist band stitching of Lower Stitched in single rows with chain stitch on the elastic * Lining seams Inverted * Bartack Stitching ( Reinforcement Stitching ) at stress bearing areas Pocket opening
RequiredCentre of Waist Band Seam and bottom hem and other stress bearing areas * Tunnel at Waist Band for Lower Two holes stitched to allow the draw cord with insertion free movement * Stitches per dm ( min ) 36 * COLOUR/PRINT Colour Multicolour Contrasting Pannels Any other colour as per buyer's requirements * Multicolour Contrasting Pannels Any other colour as per buyer's requirements - * Sublimation Printing (for 100 % polyester only) Without Without Sublimation Print as per buyer's requirements - * Colourfastness to Light ( IS 2454 ) 5 * 5/9 Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3)) Change in Colour- 4; Staining of Adjacent Fabric- 3-4 * Colourfastness to Rubbing ( IS 766 ) Dry- 4/Wet- 3 * Colourfastness to perspiration ( IS 971 ) 4 * Colour of Mesh Lining Any other colour as per buyer's requirements Any other colour as per buyer's requirements Any other colour of Mesh Lining as per buyer's requirements - * Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3))- Mesh Lining Change in Colour- 4; Staining of Adjacent Fabric- 3-4 * Colourfastness to perspiration ( IS 971 )- Mesh Lining 4 * Colour of Piping Material Any other colour as per buyer's requirements * Any other colour as per buyer's requirements - * OTHER REQUIREMENTS Pilling Resistant [after 5 hours Test as per IS 10971 (Part 1)]
Requiredmin 4 * Dimensional stability to washing
RequiredShrinkage or Elongation Percentage
Requiredmax ( IS 2977 latest)
Requiredin lengthwise and widthwise direction 1 1 LOGO AND MARKING Logo/Totem Marking As per buyer's requirements As per buyer's requirements Type of Logo Printed Printed Number of Logos on Upper 1 1 Number of Logos on Lower 1 1 Size
RequiredDesign and Location of Logo as per buyer's requirement - * TEST REPORT Availability of Test Report from designated AHSP NABL/ILAC accredited or Central Yes Yes 6/9 Government Lab to prove conformity of products to the specification Test Report No - * Test Report Date - * Name of the Lab - * Address of the Lab - * Test reports to be furnished to buyer on demand
Requiredif claimed to be available Yes * ADVANCE SAMPLE Agree to provide Advance Sample(s) for buyer's approval before commencement of supply Yes Yes * Specifications highlighted in bold are the Golden Parameters. * Bidders may note that In respect of non-golden Parameters
Requiredthe specifications 'Values' chosen by Buyer will generally be preferred over 'Bid requirement ( allowed Values) by the Buyer.
