GE (N) P/TOKEN- 66 OF 2020-2021REPAIRS TO FLOORING, HARDSTANDING, PATH AND CERTAIN MISC CIV WORKS IN THE AREA OF MANOJ PANDEY, NIRMAN VIHAR, KAHUN ROAD, PG ROAD AND CERTAIN MISC AREA OF AGE B/R (CENTRAL) UNDER GE (N) PUNE

Amount

Dismantling floor, hearth or wall tiling/paver block/chequered tiles including cement mortar bedding (but not backing), removing rubbish off the premises complete all as directed.

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregates) as in sub base including demolition of existing PCC and removing rubbish off the premises complete all as specified and directed.

M&L for 25mm thick coloured Glossy rubber moulded Chequered cement concrete tiles of area exc. 0.08 Sqm and n.exc 0.16 Sqm each, set, jointed and pointed in net cement slurry mixed with grey cement and pigment in floors including 15 mm thick screed bed or bedding layer of cement mortar (1:6) for laying floor finishes complete all as specified and as directed.

Material and labour for 60 mm thick, machine made glossy rubber moulded coloured precast cement concrete interlocking paver blocks M-35 (Grade of concrete), of triangular/ Zigzag/ Haxagone/ any shape or design as approved by GE, with grey cement and pigment and conforming to IS 15658-2006, laid over and including a layer of 25 mm thick sand cushion including filling the joints with sand as in floors/ paths/ pavings etc. complete all as specified and directed.

M&L Brick work with fly ash old size bricks, straight or curved on plan exc. 6m mean radius, built in cement mortar 1:6 including demolition of brickwork/ block masonary built in cement mortar complete all as specified and directed.

Taking down cement plaster any description on brick/ stone walling including raking out joints, hacking for key, scrubbing down with water etc complete all as directed.

M&L for rendering 15mm thick in CM (1:6) on fair faces of brick or concrete surfaces finished even and smooth without using extra cement with sagol finish complete all as specified and as directed.

M&L for rendering 15mm thick in CM (1:6) on other than fair faces of brick or concrete or stone surfaces finished even and smooth without using extra cement, complete all as specified and as directed.

M&L for preparation of new plastered or unplastered surfaces and applying two coats of cement base paint over a coat of cement primer all as specified and directed.

M&L for preparation of new plastered or unplastered wall surfaces of any description over 10cm girth or width not otherwise described and applying two coats of acylic distemper over a coat of primer all as specified and directed.

Material and labour for removing of plants, bushes, weeds with roots from walls, roof, chajja, canopy, parapets, roof kerbs, around water tanks, stagings, outlets junctions of water pipe lines , waste water pipe, bends and filling the disturbed area with cement concrete (1:1.5:3) or cement mortar (1:3) using water proofing compound as per manufacturer's instruction and making the patch finished as per surroundings complete all as specified and as directed. (Note: Rate quoted is deemed to be included for scaffolding, safety measured required for working on or up to height of 15 metres vertical slopes)

Material and labour for preparation of old wooden surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler and applying one or more coats of french polish till the desired finish is obtained complete all as specified and as directed.

Material and labour for scrapping out old treated wooden surfaces in floors, staircase etc ,sanding the surfaces using sanding machine, application of resin pigment and hardener to desired colour and finally applying two or more coats of melamine polish with spray guns, compressor etc complete till glossy surface is obtained complete all as specified and as directed.

All as per serial item No. 13 here-in-before but as in wooden doors, window and wall paneling.

Supply and fix for 0.50mm thick pre-painted galvalume aluminium zinc coating (AZ-150) GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws with side lap complete including dismantling unserviceable asbestos cement (Corrugated, Semi corrugated etc.) sheets all as specified and as directed.

S&F in repair for 6mm thick asbestos cement, corrugated or semi corrugated sheets in roof, fixed with L-type or J-type or cranked hook bolts etc. complete all as specified and as directed.

S&F in repair for 6mm thick asbestos cement, two piece adjustable serrated ridge for corrugated or semi corrugated sheets fixed with L-type or J-type or cranked hook bolts etc. complete all as specified and as directed.

Dismantling structural steel work including doors, gates, framed truss etc. complete all as directed.

Supply and fix for mild steel work in tubular /square/rectangular trusses , purlins etc including special shaped washer etc. complete using hollow mild steel sections round, square or rectangular for structural use as in main and cross beams, hip and jack rafters, purlins conforming to IS 4923:1997 grade St.-240 fixed with angle cleats or other connecting plates complete all as specified and as directed.

Supply and fix for rolled mild steel section Fe 410-W(Gde-E-250) quality A as in main and cross beams, hip and jack rafters, purlins connected to common rafters and running rails and guides for sliding doors, column posts, wind ties, fixed with angle cleats or other connecting plates, drilled for fixing all as specified and directed.

M&L for mild steel framed work such as grill, gate etc with ends of bars shouldered or rebated or forged into spike framed guard bars barred iron doors, ladders, framed baluster, walk way, railing; frame work, including pintle hinges, stops, hand-made sliding bolts etc,sliding channels for sliding of gate and similar work conforming to Fe 290 Gde-E-165 complete all as specified & as directed.

Removing excavated soil, debris obtained from demolition from various locations (other than this work) from site to outside MOD land complete all as as directed. The location at out side MOD land for disposal shall be located by the contractor himself).

Dismantling wall/ceiling boards any type, any thickness including grid/cover fillets complete all as spd and directed

Material and labour for 12mm to 12.5mm thick mineral fibre board false ceiling on and including GI powder coated grid work of size 600 mm x 600 mm with using 32.5mm x 23.5mm x 1.5 mm thick main tee, 25 mm x 23.5 mm x 1.28 mm cross tee and 25mm x 23.5mm x 1.2mm angle fixed to wall for false ceiling including necessary supporting hanger with 3.0mm dia GI wire and 'J' bolts washer nuts for securing frame work to ceiling, suspended @ 120 cm C/C both ways, size of grid shall be 605 mm x 605 mm complete all as specified and as directed. Make :- Armstrong, Diaken, New Age (ACE). Note: Height of ceiling is above 5 metres.

Material and labour for false ceiling with Single layer of size 1800mm x 1200mm x 12.5mm thick, tapered edge gypsum board (Gypboard) Plain (conforming to IS 2095-Part 1:2011, Certified board) is then screw fixed to ceiling section with 25mm drywall screws {Material-Carbon steel EN-ISO 7049/50, Finish-Case hardened Grey Phosphating} at 230mm centres on ceiling section & 150mm at periphery of ceiling. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Gyproc Pro-Fill Jointing compound (Conforms to ASTM C475), Gyproc Joint Paper tape fixed on metal grid of hot dipped galvanized steel sections and suspended as per manufacturer's specifications and instructions complete all as specified and as directed. Make: Gyproc-Saint Gobain or equivalent of Armstrong, Diaken, New Age (ACE) as approved by GE.

Material and labour for plaster of paris decorative cornices/ moulding to the pattern as approved, cross sectional area exceeding 13 Sq.cm and not exceeding 25 Sq.cm and fixed in decorative pattern including preparation of surfaces and applying two coats of oil bound distemper over a coat of primer matching with the colour of ceiling including dismantling existing complete all as specified and as directed.

Material and labour for 18mm thick plywood, grade BWR, type BB, number of ply 9 Nos, fixed with fevicol and nails for working table/ storage almirah/wall panelling to the size and pattern including taking down existing complete all as shown on drawing and as directed.

Material and labour for 12mm thick plywood, grade BWR, type BB, number of ply 7 Nos, fixed with fevicol and nails for working table/ storage almirah/wall panelling to the size and pattern including taking down existing complete all as shown on drawing and as directed.

Material and labour for 6mm thick plywood, grade BWR, type BB, number of ply 5 Nos, fixed with fevicol and nails for working table/ storage almirah/wall panelling to the size and pattern including taking down existing complete all as shown on drawing and as directed.

Material and labour for 0.90mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer’s instruction on horizontal and vertical surfaces etc. complete all as specified and as directed.

Material and labour for 1st class hard wood cover fillets, bull nosed, splayed, chamfered or rounded on one edge or face, wrought, secured with fevicol and nails, sectional area exc. 3 Sq.cm but not exc. 6 Sq.cm complete all as specified and as directed.

Material and labour for 1st class hard wood cover fillets, bull nosed, splayed, chamfered or rounded on one edge or face, wrought, secured with fevicol and nails, sectional area exc. 6 Sq.cm but not exc. 13 Sq.cm complete all as specified and as directed.

Material and labour for 1st class hard wood cover fillets, bull nosed, splayed, chamfered or rounded on one edge or face, wrought, secured with fevicol and nails, sectional area exc. 13 Sq.cm but not exc. 25 Sq.cm complete all as specified and as directed.

S&F stainless steel auto close/ hydraulic hinge suitable for shutter of not exc 0.50 sqm area complete all as specified and as directed.

S&F stainless steel hinges 50 mm long for cupboard shutter complete all as specified and as directed.

S&F 75 mm long stainless steel handles for cupboard shutter complete all as specified and as directed.

Material and labour for 4mm thick one side decorative group match veneer plywood and application of resin pigment and hardener to desired colour and pattern and applying two or more coats of melamine polish with spray guns, compressor etc till the desired glossy surface is obtained including taking down existing complete all as specified and as directed.

Preparation of old treated plastered surface of wall by filling cracks by crack fill paste of Berger or equivalent make as approved by GE, removing loose paints etc , removing nails etc and make good surface by applying white birla/JK wall putty wherever required, smoothen surface by sand paper and applying one coat of acrcylic distemper complete all as specified and as directed.

M&L for one subsequent coat of acrcylic distemper complete all as specified and as directed.

Preparation of old treated plastered/ false ceiling surface of ceiling by filling cracks by crack fill paste of Berger or equivalent make as approved by GE, removing loose paints etc , removing nails etc and make good surface by applying white birla/JK wall putty wherever required, smoothen surface by sand paper and applying one coat of acrcylic distemper complete all as specified and as directed.

M&L for preparation of old surfaces of wood and wooden based material of any description over 10cm width or girth and applying one coat of synthetic enamel paint.

M&L for preparation of old painted steel surfaces of any description over 10cm girth or width and applying one coat of synthetic enamel paint.

M&L for preparation of old painted wooden/asbestos surface of any description over 10cm girth or width in ceiling and applying one coat of synthetic enamel paint

M&L for preparation of new steel surfaces of any description over 10cm girth or width and applying two coats of synthetic enamel paint over a coat of primer .

Note : 1. Rerformance security:- Refer Condition 22 of Special Conditions. 2. Quoted Contract Sum shall be arrived at after deducting the amount of Credit Schedule (refer Schedule of Credit in pdf form for quantity, rate and amount etc.) for old unserviceable materials retrieved from site.

L.T Associate

M/s Akshay Contruction

Pratap enterprises

OM INFRA