Construction of Reservoir, Intake Well and Pump House and Ancillary Structures, Supply, Delivery, Erection, Testing and Commissioning of related Electro Mechanical and Piping works including 1 Month Trial Run and Two year Operation and Maintenance.

Amount

RESERVOIR: Cutting the shrubs, bushes, cleaning, removing & disposing the debris away from the site by private vehicles with all leads and lifts including leveling, dressing the ground with supply of all labour, T&P, taxes , hire and running charges of vehicles including fuel, consumables, tollage,excluding GST etc. complete as directed by the Engineer-in-Charge.

Earth work in all kind of soil (For Foundation & Plinth) with initial lead and lift including rough dressing and leveling the bed, depositing the excavated material away from the site in layers not exceeding 0.3m in depth and the Earth transported by transport vehicles, including cost of all labour, sundries, tools and plant, shoring, strutting, dewatering, etc., complete is all respects, excluding cost of GST, as directed by the Engineer-in-charge.

Back Filling in foundation and plinth with excavated materials (For Reservoir Bund) including watering and ramming with supply of all materials, labour, T&P, taxes,transportation,etc. all complete but excluding GST as directed by Engineer-in-charge.

Compacting and watering upto OMC rolling earth work with VRR in embankment in layers not exceeding 0.23m including watering the surfacing as required all complete with supply of all material labour, hire and running charges of the roller and tanker cost,with supply of all materials, labour, T&P, taxes,transportation, etc. all complete but excluding GST as directed by Engineer-in-charge. (Measurement to be taken on the finished compacted section of the fill under OMC)

Fine dressing and turfing with initial lead of 50m and 1.5m initial lift with supply of all materials, labour, T&P, taxes,transportation, etc. all complete but excluding GST as directed by Engineer-in-charge.

P.C.C(1:4:8) of using 40mm. & down C.B.G chips of approved quality in foundation & plinth including mixing hosting, laying to proper level & slope compacting, curing, watering charges with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Brick work in Fly Ash Bricks of size 25cm x 12cm x 8cm having crushing strength not less than 75 Kg/Cm2 to 99Kg/Cm 2 with C.M (1:4) including splay/cutting, racking out the joints curing, hoisting, staging at any height with cost and supply of all materials, labour, T&P, taxes, royalties, transportation charges, curing, testing charges etc. all complete but excluding cost of GST as per direction of Engineer-in-Charge .

12mm thick Cement plaster with cement mortar (1:4) proportion, over brick work including racking out the joints, finished smooth to the exposed surface, rounding the corners wherever found necessary including cost & supply of all materials, labour, T&P, staging, scaffolding, watering, curing, taxes, tollage, royalties, etc. complete but excluding cost of GST as per direction of Engineer-in-charge .

Supply & Filling in foundation and plinth with sweet sand (Good Quality without stones or sharp objects) in layers of 50mm thick, including watering and ramming ,with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Supplying and laying 200 Micron polythene separation membrane (LDPE Sheer as per IS 2508, Grade 030) with overlapping of 300 mm at joints including cleaning the surface before placing the membrane etc., complete with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge. (N.B. : No payment will be made for overlapping.)

Welding of LDPE Sheet joints in situ by heat sealing (Thermal Fusion) using branded machines having automatic thermostat control and speed control, with a minimum total welding width of 50mm either as a single or 2 or 3 seams , during laying of the film and checked carefully etc., complete with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Supplying and laying 200 GSM Non Woven Geotextile Fabric with overlapping of 200 mm at joints including cleaning the surface before placing the membrane with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge. (N.B. : No payment will be made for overlapping.)

C.C. M25 for R.C.C. works using 20mm and 10 mm size C.B.G. chips for all floors, foundation & plinth etc. of approved quality, mixing with a concrete mixture as per approved design mix, hoisting, laying, compacting with40 to 60 needle vibrator, curing with cost and supply of all materials, labour, T&P, taxes,transportation, testing charges royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Supply TOR/TMT Steel of Fe- 500 confirming to IS-1786 including cutting, straightening, bending, binding & placing the grills in position for RCC works binding the grills with binding wire of 18 to 20 gauge including supply of steel, labour, materials, transportation charges, T&P, taxes, etc. all complete but excluding GST as per the direction of Engineer-in-charge. (NB: No payment shall be made for extra weight than theoretical co-efficient).

Supply and Installation of 80mm Dia PP Ball Type Flanged End Foot Valve with screen, in base slab of reservoir, at one valve for every 36 Sq.m, complete with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Providing and fixing at or near ground level factory made RCC pavement slab of M-30 grade of size 450x450x50 mm, including reinforcement with 6 mm dia M.S. bars 4 nos on each side, including setting in position in footpath/bund to the required level and line over a bed of 20 mm average thick cement mortar 1:5 (1 cement : 5 coarse sand), having joint thickness not more than 5mm except on curve, including filling of joints with same cement mortar and making grooves,with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Precast CC M 25 Kerb Stone of Size 450mm Height x 100mm Thickness Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge. (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying factory made chamfered edged cement concrete paver blocks in footpath, park lawn, drive way or light traffic parking etc. M30 strength and 80 mm thick, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand , compacting and proper embedding /laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting the paver blocks as per required size and pattern, sweeping the surface with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

C.C. M20 for R.C.C. works using 20mm and 10 mm size C.B.G. chips for all floors, foundation & plinth etc. of approved quality, mixing with a concrete mixture as per approved design mix, hoisting, laying, compacting with40 to 60 needle vibrator, curing with cost and supply of all materials, labour, T&P, taxes,transportation, testing charges royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Providing rigid smooth leak proof centering & shuttering made of steel/ply, plank of approved quality for R.C.C. structures and deshuttering and removing the same after due period with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Wall painting two coats with 100% Acrylic emulsion paint (1st quality) exterior grade of approved make & shade to make an even finished surface over a coat of primer with water bond cement primer in all heights with all scaffolding and staging charges including cost and supply of all materials, labour, T&P, all taxes, transportation charges etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Supply and Fixing decorative street light post of 3m height made of 65mm (2 1/2") GI Pipe class B with 230mm x 230 mm x 6mm M.S. base plate duly welded, with concreting, with construction of masonry pedestal, with suitable SMC Box to house 16 A control switch 16 A MCB unit (500 V ) etc. with suitable angle iron frame work, with door and with lock and key arrangements and with supply and fixing of 120 W LED street light fitting with integrated driver, .6 mtr of 32mm dia GI pipe (Class B) arm pipe, complete with necessary clamp on the post with PVC unsheathed lead's with painting of suitable colour, with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Supply & Laying of 1.1 kV grade XLPE insulated, XLPE sheathed Aluminium, steel armoured power cable as per IS 7098. The cable shall be laid on trench / cable trays / Hume pipes / Buried under ground. Rate to exclude cost of trays, pipes and supporting Item (PPT-SOR)s but including necessary cable clamps. - 4C x 6Sqmm with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Supplying and making end termination with brass compression gland for following sizes of XLPE insulated and PVC sheathed aluminium conductor cable of 1.1 KV grade as required. - 4C x 6Sqmm with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Supplying and making end termination with Al lugs for following sizes of aluminium conductor cable of 1.1 KV grade as required. 6 Sqmm with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

INTAKE WELL& PUMP HOUSE- Cleaning Cutting the shrubs, bushes, cleaning, removing & disposing the debris away from the site by Private Vehicles with all leads and lifts including leveling, dressing the ground with supply of all labour, T&P, taxes excluding GST, hire and running charges of vehicles including fuel, consumables, with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Cleaning of Water Hyacinth from Canal and Drainage Channels (Thickly Grown) with supply of all materials, labour, T&P, taxes,transportation, etc. all complete but excluding GST as directed by Engineer-in-charge.

Back Filling in foundation and plinth(Bund Formation) with excavated materials moorum including watering and ramming with supply of all materials, labour, T&P, taxes,transportation, etc. all complete but excluding GST as directed by Engineer-in-charge.

Earth work in all kind of soil (For Foundation & Plinth) with initial lead and lift including rough dressing and leveling the bed, depositing the excavated material away from the site in layers not exceeding 0.3m in depth and the Earth transported by transport vehicles, including cost of all labour, sundries, tools and plant, shoring, strutting, dewatering, etc., complete is all respects, excluding cost of GST, as directed by the Engineer-in-charge.

Earth Work Excavation below water level in clayey soil for intake well including charges for special tools and plants for bailing/pumping etc., such as air compressor and helmet ,with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Labour for sinking wells in all kinds of soil other than rock, to lines, levels and plumb by scooping out from inside and below the staining including cost of necessary tools and plant supplying and working of pumps bailing out of water or dredging, removal of all materials and obstacles from inside the well by divers, hire and labour for cantiledge jetting, if necessary and sinking to a depth of 10M taking precaution against shifting and tilting disposal of the spoil with all leads and lifts,with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.( For 7.0m Internal Dia/7.6m External Dia)

Supply at Site, Installation & continuous Running of suitable capacity Well Point Dewatering System for the entire duration of the works in the canal bed complete with installation of required number of well points, header pipe for interconnection of the well points, skid mounted diesel pump pumping system, piping up to suitable disposal point, dismantling and removing the system from site after completion of the work, etc., complete to maintain the water level below the required depth for achieving a dewatered working area, including cost & supply of all materials, mobilisation & demobilisation, labour, T&P, running charges, operator charges,with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

P.C.C(1:4:8) of using 40mm. & down C.B.G chips of approved quality in foundation & plinth including mixing hosting, laying to proper level & slope compacting, curing, watering charges etc. complete with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

C.C. M 30 for R.C.C. works using 20mm and 10 mm size C.B.G. chips for all floors, foundation & plinth etc. of approved quality, mixing with a concrete mixture as per approved design mix, hoisting, laying, compacting with 40 to 60 needle vibrator, curing,water charges, all testing charges with supply of all materials, labour, T&P, taxes,transportation, testing charges royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

M 30 Concrete for Raft

M 30 Concrete for Shoe

M 30 Concrete for Side Wall

M 30 Concrete for Cover Slab & Platform (At 5.5m Height above bed Level)

M 30 Concrete for Mid Level Slab Projection

M 30 Concrete for Roof Slab (At 10.0m Height from bed level)

M 30 Concrete for Columns (At 6.0m to 10m Height from bed level)

M 30 Concrete for Lintel & Sunshade (At 8.0m Height from Bed Level)

Supply Tor/TMT Steel of Fe- 500 confirming to IS-1786 including cutting, straightening, bending, binding & placing the grills in position for RCC works binding the grills with binding wire of 18 to 20 gauge including supply of steel,all materials, labour, T&P, taxes,transportation, testing charges royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge. (NB: No payment shall be made for extra weight than theoretical co-efficient).

Providing rigid smooth leak proof centering & shuttering made of steel/ply, plank of approved quality for R.C.C. structures and deshuttering and removing the same after due period with supply of all materials, labour, T&P, taxes, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Shuttering - For Shoe (Circular & Angular)

Shuttering - For Side Walls - Circular

Shuttering - For Cover Slab (Flat) -10m Staging

Shuttering - For Mid Level Slab Projection

Shuttering - For Roof Slab (Flat) -5.0m Staging

Shuttering - For Columns

Shuttering - For Lintel & Sunshade

Providing 52 mm thick Cement Concrete Flooring(Grano Flooring) with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications,with supply of all materials, labour, T&P, taxes,transportation, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

6 MM thick Cement plaster with cement mortar (1:4) proportion, over RCC work including racking out the joints, finished smooth to the exposed surface, rounding the corners wherever found necessary including cost & supply of all materials, labour, T&P, staging, scaffolding, watering, curing, taxes, tollage, royalties, etc. complete but excluding cost of GST as per direction of Engineer-in-charge

16 MM thick Cement plaster with cement mortar (1:6) proportion, over brick work including racking out the joints, finished smooth to the exposed surface, rounding the corners wherever found necessary including cost & supply of all materials, labour, T&P, staging, scaffolding, watering, curing, taxes, tollage, royalties, etc. complete but excluding cost of GST as per direction of Engineer-in-charge

6 MM thick Cement plaster with cement mortar (1:4) proportion, over RCC work/ ceiling including racking out the joints, finished smooth to the exposed surface, rounding the corners wherever found necessary including cost & supply of all materials, labour, T&P, staging, scaffolding, watering, curing, taxes, tollage, royalties, etc. complete but excluding cost of GST as per direction of Engineer-in-charge .

Providing and laying water proofing with polymeric bituminous membrane (plastic felt) of 3.0 Kg/Sqm. and 2mm. thickness consisting of layers having center core of 20 microns thermoplastic height molecular high density polyethylene H.M.H.D. P.E film of grade 2504 including priming the surface with bitumen’s prime @0.3 Kg/Sqm. providing a coat of hot blown bitumen of 1.32Kg/Sqm. applying and laying plastic felt membrane with 10Cm. overlap adhered to blown bitumen of 85/25 or 90/15 grade and covered with a layer of hot blown bitumen @ 1.2 Kg/Sqm. with supply of all materials, labour,staging, scaffolding,T&P, taxes, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

25mm. (av) thick graded cement concrete in C.C.(1:2:2) using 12mm. to 6mm. size hard granite chips of approved quality including cleaning the roof top, washing, mixing, hoisting laying to proper level slope, gradient making rounding hunching at the corners, joints, finished smooth to exposed surface over 2 coats of WPC as water proofing course with cost and supply of all materials, labour, T&P, taxes, tollage transportations, with supply of all materials, labour, T&P, taxes, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Providing and Placing in position Dumb Bell with Central Bulb (180mm Wide x 8mm Thick) PVC water stops conforming to IS 12200 for construction joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete with supply of all materials, labour, T&P, taxes, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Preparing the surfaces by through scrapping, cleaning and painting the same with two coats of food grade epoxy paint over a coat of epoxy primer of approved quality, etc. Complete including all staging, scaffolding, above 4.60mtr,Iabour, all taxes, tollage, materials, fuel, brushes, tools,with supply of all materials, labour, T&P, taxes, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Brick work in Fly Ash Bricks of size 25cm x 12cm x 8cm having crushing strength not less than 75 Kg/Cm2 to 99Kg/Cm 2 with C.M (1:6) including splay/cutting, racking out the joints curing, hoisting, staging at any height with cost and supply of all materials, labour, T&P, taxes, royalties, transportation charges, curing, testing charges etc. all complete but excluding cost of GST as per direction of Engineer-in-charge .

12 MM thick Cement plaster for Walls with cement mortar (1:4) proportion, over brick work including racking out the joints, finished smooth to the exposed surface, rounding the corners wherever found necessary including cost & supply of all materials, labour, T&P, staging, scaffolding, watering, curing, taxes, tollage, royalties, etc. complete but excluding cost of GST as per direction of Engineer-in-charge

P.C.C(1:4:8) of using 40mm. & down C.B.G chips of approved quality in foundation & plinth including mixing hosting, laying to proper level & slope compacting, curing, watering charges with supply of all materials, labour, T&P, taxes, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

One coat Priming with water bond cement primer to the newly plaster surface of the exterior Wall or over the existing putty surface of the interior wall of approved make & shade to make an even finished surface in all heights with all scaffolding and staging including cost and supply of all materials, labour, T&P, all taxes, transportation charges, royalties, tollage, etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Exterior painting two coats to wall surface with acrylic based weather coat paint of approved quality & shade having resistance to Fungus, Fading, including scraping, cleaning, brushing, washing the old paint, as and when required, removing the flakes applying uniformly two coats including cost and supply of all materials, labour, T&P, taxes, transportation, staging, scaffolding, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Distempering two coats of approved quality and shade to New work including supplying cleaning, brushing, the old paint, removing the flakes and finishing smooth the wall surface by applying plaster of paris or wall putty where required, sand papering including cost & supply of all material labours, T&P scaffoldings, taxes, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

White Washing two coats with shell lime of approved quality and shade to ceilings including supplying cleaning, brushing, the old paint, removing the flakes and finishing smooth the surface by applying plaster of paris or wall putty where required, sand papering with supply of all materials, labour,staging,scaffolding, T&P, taxes, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Supplying, fitting, fixing up Al Window (sliding type) made up aluminum Section 9778 as window frame, section No. 4095, 4096 & 9777, 3994 as shutter frame with 5mm thick black glass as panel fitted with rubber beading including locking arrangement including all fitting including cost and supply of all materials, labour, T&P, taxes, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Supplying and erection of pull and push type Rolling Grill with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges, fixing in position, with supply of all materials, labour, T&P, taxes, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Supplying, fitting and fixing of Stainless steel of 304 grade in hand railing using 50mm dia of 2mm thick circular pipe with Balustrade of size 32mm x 32mm x 2mm @ 0.90mtr. C/C and stainless square pipe bracing of size 32mm x 32mm x 2mm in 3 rows in stair case as per approved design and specification, buffing, polishing etc. with supply of all materials, labour, T&P, taxes,transportation charges, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Providing ,fitting and fixing the fabricated MS structures after cutting,bending,making holes,jointing,welding as per requirement and hoisting fabricated structurals,placing in position as per the drawing or as directed with supply of all materials, labour,machinery,costof fuel,electrode ,gas ,consumables,hire & running charges of all kind of equipments, T&P, taxes,transportation charges, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Supply of CI Puddle Pipe & Labour Charges for Installation of Puddle Pipes of various sizes (200mm Dia to 600mm Dia) in position true to line and levels in RCC Circular Side Wall including all charges, Cutting & reworking of Reinforcement rods, shuttering as required, with supply of all materials, labour, T&P, taxes,transportation charges, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Supply and Fixing in Position SS 316 Inlet Screen (20mm Sq opening grating made of 3.0mm dia rods) with Flanged Ends to suit 450mm Dia Pipe complete with inverted box hood with 3mm Tk. SS Plates of sufficient size covering the screen complete including cost of Gasket, SS Bolt & Nuts, with supply of all materials, labour, T&P, taxes,transportation charges, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

ACCESS TO INTAKE WELL PUMP HOUSE-- Providing double bulb under reamed bored pile foundation of following dia & length long reinforced cement concrete of M-20 grade using 12mm size black hard granite (C.B) stone chips, boring from existing ground level with removal of obstruction if any, using bentonite, providing required reinforcement as per drawing making the end of the cage to Conical shape, welded properly, providing 2.5 times pile dia under ream at appropriate level and disposal the boring earth from work site with supply of all labour, T&P, taxes, hire & running charges of all machineries required for the work with supply of all materials, labour, T&P, taxes,transportation charges, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge. (excluding cost of reinforcement steel and binding wire). - 450mm Dia x 8.0m Long

Earth work in all kind of soil (For Foundation & Plinth) with initial lead and lift including rough dressing and leveling the bed, depositing the excavated material away from the site in layers not exceeding 0.3m in depth and the Earth transported by transport vehicles, including cost of all labour, sundries, tools and plant, shoring, shuttering, dewatering, etc., complete is all respects, excluding cost of GST, as directed by the Engineer-in-charge.

P.C.C(1:4:8) of using 40mm. & down C.B.G chips of approved quality in foundation & plinth including mixing hosting, laying to proper level & slope compacting, curing, watering charges with supply of all materials, labour, T&P, taxes,transportation charges, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

C.C. M 30 for R.C.C. works using 20mm and 10 mm size C.B.G. chips for all floors, foundation & plinth etc. of approved quality, mixing with a concrete mixture as per approved design mix, hoisting, laying, compacting with40 to 60 needle vibrator, curing with cost and supply of all materials, labour, T&P, taxes, testing charges tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

M 30 Concrete for Pile Cap

M 30 for Columns

M 30 For Tie Beam in Bed of Reservoir

M30 For Deck Slab Beams

Supply Tor/TMT steel of Fe- 500 confirming to IS-1786 including cutting, straightening, bending, binding & placing the grills in position for RCC works binding the grills with binding wire of 18 to 20 gauge including supply of steel,materials, labour, T&P, taxes,transportation charges, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge. (NB: No payment shall be made for extra weight than theoretical co-efficient).

Providing rigid smooth leak proof centering & shuttering made of steel/ply, plank of approved quality for R.C.C. structures and deshuttering and removing the same after due period with supply of all materials, labour, T&P, taxes, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Shuttering - For Pile Cap

Shuttering - For Columns

Shuttering - For Tie Beam

Shuttering - For Deck Slab

C.C. M 30 for R.C.C. works using 20mm and 10 mm size C.B.G. chips for all floors, foundation & plinth etc. of approved quality, mixing with a concrete mixture as per approved design mix, hoisting, laying, compacting with40 to 60 needle vibrator, curing with cost and supply of all materials, labour, T&P, taxes, testing charges tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

6 MM thick Cement plaster with cement mortar (1:4) proportion, over RCC work/ ceiling including racking out the joints, finished smooth to the exposed surface, rounding the corners wherever found necessary including cost & supply of all materials, labour, T&P, staging, scaffolding, watering, curing, taxes, tollage, royalties, etc. complete but excluding cost of GST as per direction of Engineer-in-charge

Supplying, fitting and fixing of Stainless steel of 304 grade in hand railing using 50mm dia of 2mm thick circular pipe with Balustrade of size 32mm x 32mm x 2mm @ 0.90mtr. C/C and stainless square pipe bracing of size 32mm x 32mm x 2mm in 3 rows in stair case as per approved design and specification, buffing, polishing etc. with cost and supply of all materials, labour, T&P, taxes, transportation ,tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Special Arrangements Like Caisson/ sheet piling / Bund Formation / under water execution with divers, etc., as suitable for the site condition, including dewatering arrangements by pumping or compressor as required, for execution of Pile caps in the bed of the canal, with supply of all labour, T&P, taxes, hire & running charges of all machineries required for the work etc. with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.(For Each Pile)

CREEK / NALLAH CROSSING PIE BRIDGE Providing double bulb under reamed bored pile foundation of following dia & length long reinforced cement concrete of M-20 grade using 12mm size black hard granite (C.B) stone chips, boring from existing ground level with removal of obstruction if any, using bentonite, providing required reinforcement as per drawing making the end of the cage to Conical shape, welded properly, providing 2.5 times pile dia under ream at appropriate level and disposal the boring earth from work site with cost and supply of all materials, labour, T&P,hire & running charges of all machineries required for the work, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge. (excluding cost of reinforcement steel and binding wire). - 450mm Dia x 8.0m Long

Earth work in all kind of soil (For Foundation & Plinth) with initial lead and lift including rough dressing and leveling the bed, depositing the excavated material away from the site in layers not exceeding 0.3m in depth and the Earth transported by transport vehicles, including cost of all labour, sundries, tools and plant, shoring, strutting, dewatering, etc., complete is all respects, excluding cost of GST, as directed by the Engineer-in-charge.

P.C.C(1:4:8) of using 40mm. & down C.B.G chips of approved quality in foundation & plinth including mixing hosting, laying to proper level & slope compacting, curing, watering charges etc. complete with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Providing fitting and fixing the fabricated MS structures after cutting, bending, making holes, jointing, welding as per requirement and Hoisting fabricated structural, placing in position as per the drawings or as directed with supply of labour and material, machinery, cost of fuel, electrode, gas, consumables hire and running charges of all kind of equipment's with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

C.C. M 30 for R.C.C. works using 20mm and 10 mm size C.B.G. chips for all floors, foundation & plinth etc. of approved quality, mixing with a concrete mixture as per approved design mix, hoisting, laying, compacting with40 to 60 needle vibrator, curing with cost and supply of all materials, labour, T&P, testing charges taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

M 30 Concrete for Pile Cap

M 30 for Columns

M30 For Trestle Beams

Supply Tor/TMT steel of Fe- 500 confirming to IS-1786 including cutting, straightening, bending, binding & placing the grills in position for RCC works binding the grills with binding wire of 18 to 20 gauge including supply of steel, labour, materials, transportation charges, T&P, taxes, etc. all complete but excluding GST as per the direction of Engineer-in-charge. (NB: No payment shall be made for extra weight than theoretical co-efficient).

Providing rigid smooth leak proof centering & shuttering made of steel/ply, plank of approved quality for R.C.C. structures and deshuttering and removing the same after due period with supply of all materials, labour, T&P, taxes, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Shuttering - For Pile Cap

Shuttering - For Columns

Shuttering - For Trestle Beam

Special Arrangements Like Caisson/ sheet piling / Bund Formation / under water execution with divers, etc., as suitable for the site condition, including dewatering arrangements by pumping or compressor as required, for execution of Pile caps in the bed of the canal, with supply of all labour, T&P, taxes, hire & running charges of all machineries required for the work etc. all complete excluding GST and as per direction of Engineer in charge.(For Each Pile)

Painting two coats with approved quality & shade enamel paint on new iron work over one coat of red oxide primer including scraping, cleaning, the surface sand papering, filling the holes with wax putty etc. all complete including cost and supply of all materials, labour, T&P, all taxes, transportation charges, staging, scaffolding, etc. all complete but excluding cost of GST as per direction of Engineer-in- charge.

NATIONAL HIGHWAY/RAILWAY CROSSING BY TRENCHLESS TECHNOLOGY-- Excavating of driving pit and receiving pit of size 3.00m (length) x 3.50m (breadth), depth upto 5m in all soil strata including shoring and strutting using 6mm tk MS Plate of size 3.50m x 3.50m usable for 10 operations and providing 16mm thickness MS plate of size 3.00m x 3.50m with 100mm x100mm x 12mm angles of 4m length for holding the MS plates for Thrust arrangements to receive the impacts during pushing operation of encasing pipe. Lowering the following size of MS encasing pipe by using Contractor’s crane and machineries and jointing MS pipes by welding, across the National Highways/State Highways/ Railways/Canal crossing etc. and driving the horizontal bore by pushing / jacking method (trenchless technology method) using contractor’s machineries such as cranes, jacks, jacking materials, generator, welding machineries, compressor, jack hammer and other equipment's etc. without interfering and causing any hindrance to the movement of traffic or any other vehicles, without any disturbances to the railway/road/canal formation etc. including bailing / pumping of water where ever necessary without affecting any installation like water supply pipeline/telephone cable, electric cables etc. passing nearby area and scooping the earth inside the pipes and pit and depositing the surplus earth in a convenient place and leveling the site after completion of entire work as directed by EIC. The rate includes the cost of driving pit, thrust bed/wall and receiving pit to the depth of 0m to 5m excluding the cost of MS pipes. The price is also to be inclusive of complete co ordination with the Highway/Railway department during execution of the works, with cost and supply of all materials, labour, T&P,transportation, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge. - For 1000mm Dia Encasing Pipe(For Highway crossing)

Providing fitting and fixing the fabricated MS structures after cutting, bending, making holes, jointing, welding as per requirement and Hoisting fabricated structural, placing in position as per the drawings or as directed with supply of labour and material, machinery, cost of fuel, electrode, gas, consumables hire and running charges of all kind of equipment's with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.- 1000 Dia MS Pipe (1016 OD, 10mm Tk., 248 Kg/m)

Excavating of driving pit and receiving pit of size 3.00m (length) x 3.50m (breadth), depth upto 5m in all soil strata including shoring and strutting using 6mm tk MS Plate of size 3.50m x 3.50m usable for 10 operations and providing 16mm thickness MS plate of size 3.00m x 3.50m with 100mm x100mm x 12mm angles of 4m length for holding the MS plates for Thrust arrangements to receive the impacts during pushing operation of encasing pipe. Lowering the following size of MS encasing pipe by using Contractor’s crane and machineries and jointing MS pipes by welding, across the National Highways/State Highways/ Railways/Canal crossing etc. and driving the horizontal bore by pushing / jacking method (trenchless technology method) using contractor’s machineries such as cranes, jacks, jacking materials, generator, welding machineries, compressor, jack hammer and other equipment's etc. without interfering and causing any hindrance to the movement of traffic or any other vehicles, without any disturbances to the railway/road/canal formation etc. including bailing / pumping of water where ever necessary without affecting any installation like water supply pipeline/telephone cable, electric cables etc. passing nearby area and scooping the earth inside the pipes and pit and depositing the surplus earth in a convenient place and leveling the site after completion of entire work with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.The rate includes the cost of driving pit, thrust bed/wall and receiving pit to the depth of 0m to 5m excluding the cost of MS pipes. The price is also to be inclusive of complete co ordination with the Highway/Railway department during execution of the works. - 1000mm Dia Encasing Pipe(For Railway crossing)

Providing fitting and fixing the fabricated MS structures after cutting, bending, making holes, jointing, welding as per requirement and Hoisting fabricated structural, placing in position as per the drawings or as directed with supply of labour and material, machinery, cost of fuel, electrode, gas, consumables hire and running charges of all kind of equipment's with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.. - 1000 Dia MS Pipe (1016 OD, 10mm Tk., 248 Kg/m)

COMPOUND WALL FOR RESERVOIR-- Providing Single bulb under reamed bored pile foundation of following dia & length long reinforced cement concrete of M-20 grade using 12mm size black hard granite (C.B) stone chips, boring from existing ground level with removal of obstruction if any, using bentonite, providing required reinforcement as per drawing making the end of the cage to Conical shape, welded properly, providing 2.5 times pile dia under ream at appropriate level and disposal the boring earth from work site with supply of all labour, T&P, taxes, hire & running charges of all machineries required for the work with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.(excluding cost of reinforcement steel and binding wire). - 250mm Dia x 3.0m Long

Earth work in all kind of soil (For Foundation & Plinth) with initial lead and lift including rough dressing and leveling the bed, depositing the excavated material away from the site in layers not exceeding 0.3m in depth and the Earth transported by transport vehicles, including cost of all labour, sundries, tools and plant, shoring, shuttering, dewatering, etc., complete is all respects, excluding cost of GST, as directed by the Engineer-in-charge.

Back Filling in foundation and plinth with excavated materials moorum including watering and ramming with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

P.C.C(1:4:8) of using 40mm. & down C.B.G chips of approved quality in foundation & plinth including mixing hosting, laying to proper level & slope compacting, curing, watering charges etc. complete with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

C.C. M 20 for R.C.C. works using 20mm and 10 mm size C.B.G. chips for all floors, foundation & plinth etc. of approved quality, mixing with a concrete mixture as per approved design mix, hoisting, laying, compacting with40 to 60 needle vibrator, curing with cost and supply of all materials, labour, T&P, testing charges taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

M 20 Concrete for Pile Cap

M 20 Concrete for Plinth Beam

M 20 Concrete for Column

M 30 Concrete for Top Beam

Supply Tor/TMT Steel of Fe- 500 confirming to IS-1786 including cutting, straightening, bending, binding & placing the grills in position for RCC works binding the grills with binding wire of 18 to 20 gauge including supply of steel, labour, materials, transportation charges, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge. (NB: No payment shall be made for extra weight than theoretical co-efficient).

Providing rigid smooth leak proof centering & shuttering made of steel/ply, plank of approved quality for R.C.C. structures and deshuttering and removing the same after due period with supply of all materials, labour, T&P, taxes, royalties, tollage, etc. all complete but excluding GST as directed by Engineer-in-charge.

Shuttering - For Pile Cap

Shuttering - For Plinth Beam

Shuttering - For Column

Shuttering - For Top Beam

Brick work in CM 1:6 Fly Ash Bricks of size 25cm x 12cm x 8cm having crushing Brick Work in CM 1:6--strength not less than 75 Kg/Cm2 to 99Kg/Cm 2 with C.M (1:6) including splay/cutting, racking out the joints curing, hoisting, staging at any height with cost and supply of all materials, labour, T&P, taxes, royalties, transportation charges, curing, testing charges etc. all complete but excluding cost of GST as per direction of Engineer-in-charge .

12 MM thick Cement plaster with cement mortar (1:4) proportion, over brick work including racking out the joints, finished smooth to the exposed surface, rounding the corners wherever found necessary including cost & supply of all materials, labour, T&P, staging, scaffolding, watering, curing, taxes, tollage, royalties, etc. complete but excluding cost of GST as per direction of Engineer-in-charge .

One coat Priming with water bond cement primer to the newly plaster surface of the exterior Wall or over the existing putty surface of the interior wall of approved make & shade to make an even finished surface in all heights with all scaffolding and staging including cost and supply of all materials, labour, T&P, all taxes, transportation charges etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Water proof cement painting of approved quality two coat to exterior wall surface with approved quality & shade including all cost & supply of materials, engagement hire and running charges of water tanker, pump set labours, T&P, taxes, all transportation, staging, scaffoldings, curing, water charges at any height etc. Complete but excluding cost of GST as directed by the Engineer In-charge

Providing and fixing Glass Pieces (Glass Bottles broken in to suitable pieces) on top of compound wall, will laying of top tie beam concreting itself, as directed, with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but excluding GST as directed by Engineer-in-charge.

MAIN PIPELINE NETWORK Supply, Laying of Cast Iron non rising splindletype sluice valve confirming to IS 14846,PN 1.6with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Supply, Laying of Cast Iron Wafer type centric Butterfly Valve as per BSEN 593 (BS 5155/ IS 13095), CI MOC, Gear Operated, PN 1.6 (100 NB)with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Supply, Laying of Cast Iron Kinetic Air Valve (without isolating sluice valve), DK Type, conforming to IS 14845, PN 1.6(100 NB)with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Supply, Fitting GM Pressure Gauge Cock (15 NB)with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Supply,Fitting laying of Cast Iron double Flanged Swing type, Non Return Valve, conforming to IS 5312, PN 1.6 (450 )NBwith cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Supply, Laying, Fitting CI Class-B Pipe with Screwed Flange conforming, to IS 1536Pump Delivery to Common Headerwith cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

450 NB D/F CI Class-B Pipe

600 NB D/F CI Class-B Pipe

Supply, Fixing , Fitting Ductile Iron Pressure, Socket and Spigot Pipes conforming to IS 8329with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

600 NB S/S DI K9 Pipe Supply

600 NB S/S DI K9 Pipe Laying

Providing Civil Pedestal/Encasing Concrete/Thrust Block for 600 Dia Pipes of required size as per design, cost inclusive of required earth work excavation, PCC, RCC M25 Footing & Pedestal, with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Providing fitting and fixing the fabricated MS structures after cutting, bending, making holes, jointing, welding as per requirement and Hoisting fabricated structural, placing in position as per the drawings or as directed with supply of labour and material, machinery, cost of fuel, electrode, gas, consumables hire and running charges of all kind of equipment's with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Supply,fitting and fixing the CI Specials & Fittings viz., DI D/F Reducer - 200 x 450,DI D/F 90 Deg Bend - 450 NB ,DI All Flanged Reducing Tee - 600 x 450,DI All Flanged Reducing Tee - 600 x 450,DI Dummy Flange - 600 NB,DI Puddle Pipe - 600 NB - 1.5m Long,DI Flanged ,Socket - 600 NB,DI Flanged Spigot - 600 NB,DI D/F 90 Deg Bend - 600 NB,DI D/F 45 Deg Bend - 600 NB,DI S/S 90 Deg Bend - 600 NB,DI S/S 45 Deg Bend - 600 NB,DI S/S 22.5 Deg Bend - 600 NB,DI All Flanged Reducing Tee - 600 x 300,DI D/F Reducer - 300 x 100,conforming to IS 1538. with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Laying 300mm Dia pipe conforming to IS 1538. with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Laying 450mm Dia pipe . with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Laying 600mm Dia pipe conforming to IS 1538. with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Providing Flanged Joints conforming to IS 3114 to flanged Cast Iron Pipes/ DI Pipes or other pipes and fittings of the following nominal diameters including testing of joints, cost of bolts and nuts and rubber insertions as per specification with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Providing Push on Joints conforming to IS 3114 to centrifugally (spun) cast iron pipes or ductile iron pipes using Rubber Gaskets conforming to IS 5382 of SBR quality including testing of joints as per specification with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge. 600NB

Earth work in all kind of soil (For Pipe Line) with initial lead and lift including rough dressing and leveling the bed, depositing the excavated material away from the site in layers not exceeding 0.3m in depth and the Earth transported by transport vehicles, including cost of all labour, sundries, tools and plant, shoring, shuttering, dewatering, etc., complete in all respects, excluding cost of GST, as directed by the Engineer-in-charge.

Back Filling in foundation and plinth with excavated materials moorum including watering and ramming conforming to IS 1538. with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

DISTRIBUTION PIPELINE NETWORK Supply, Laying of Cast Iron Non Rising Spindle type Sluice Valve conforming to IS 14846, PN 1.6with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.(450 NB)

Supply, Laying of Cast Iron Wafer type centric Butterfly Valve as per BSEN 593 (BS 5155/ IS 13095), CI MOC, Gear Operated, PN 1.6with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.(100 NB)

Supply, Laying of Cast Iron Kinetic Air Valve (without isolating sluice valve), DK Type, conforming to IS 14845, PN 1.6(100 NB)with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.(100NB)

Supply, Fitting CI Class-B Pipe with Screwed Flange conforming to IS 1536with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.(Pump Delivery to Common Header-450 NB D/F CI Class - B Pipe)

Supply,Fitting Laying Ductile Iron Pressure, Socket and Spigot Pipes conforming to IS 8329with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.(450 NB S/S DI K9 Pipe)

Supply, Laying CI Specials & Fittings viz., DI D/F 90 Deg Bend - 450 NB, DI A/F Equal Tee - 450 NB,DI A/F Reducing Tee - 450 NB x 100 NB,DI D/F 90 Deg Long Radius Bend - 450 NB,DI Flanged Socket - 450 NB, ,DI Flanged Spigot - 450 NB,DI D/F 45 Deg Bend - 450 NB,DI S/S 22.5 Deg Bend - 450 NB,DI Dummy Flange - 450 NB,DI Puddle Pipe - 450 NB - 1.5m Long confirming to IS 1538,with supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

supply

Laying

Providing Flanged Joints conforming to IS 3114 to flanged Cast Iron Pipes/ DI Pipes or other pipes and fittings of the following nominal diameters including testing of joints, cost of bolts and nuts and rubber insertions as per specification complete.,with supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Supply, Laying Providing Push on Joints conforming to IS 3114 to centrifugally (spun) cast iron pipes or ductile iron pipes using Rubber Gaskets conforming to IS 5382 of SBR quality including testing of joints as per specification complete.(450 NB)with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.(100NB)

Earth work in all kind of soil (For Pipe Line) with initial lead and lift including rough dressing and leveling the bed, depositing the excavated material away from the site in layers not exceeding 0.3m in depth and the Earth transported by transport vehicles, including cost of all labour, sundries, tools and plant, shoring, strutting, dewatering, etc., complete is all respects, excluding cost of GST, as directed by the Engineer-in-charge.

Back Filling in foundation and plinth with excavated materials moorum including watering and ramming including cost of all labour, sundries, tools and plant, shoring, strutting, dewatering, etc., complete is all respects, excluding cost of GST, as directed by the Engineer-in-charge.

MECHANICAL WORKS Supply, Installation, Testing and 30 days continuous , successful trial running & commissioning of Vertical Clear Water Submersible Centrifugal Raw Water Pumps of approved make, of capacity 800 Cum/Hr @ 35meter Head (110 KW Approx. Rating) with Cast Iron Body & Impeller, SS Shaft, 20m Cable, etc., including cost of material, labour, for erection and conveyance charges with cost and supply of all materials, labour, T&P, taxes, tollage, royalties,all consummables etc. all complete but Excluding GST as directed by Engineer-in-charge.

HT WORKS - FOR INCOMING POWER SUPPLY--Iron core Oil Cooled Transformer with Copper Winding Conforming to IS 1180 (Part 1) of 2014 Supply, Installation, Testing and 30 days continuous , successful trial running & commissioning of 500kva,11 KV/500 KVA, three Phase 50 HZ double wound oil immersed natural air cooled, core type continuous rating, outdoor distribution power transformer with copper winding for voltage ratio 22-11 KV/433 volts between phases with neutral brought out at LV side. The transfer shall be contained in a mild steel plain & radiator cooled tank, conforming to IS 1180 (Part I) of 2014 with off-load tap switch for ±10% on L.V side and ±5 % on H.V.side. The transformer shall be supplied with first filling of oil and consisting of all the fittings and accessories such as Inspection cover, Oil level indicator with minimum and filling level markings, Externally operated off circuit tap changing switch with locking device & keys, H.V. Terminals- Bushings, L.V. Terminals cable box Rating plate, Two earthing terminals, Two lifting hooks etc. complete as per IS 1180 (Part I) of 2014 and as amended thereafter,conforming to IS 1538. with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Supply & Laying of 11 kV grade PVC insulated, PVC/XLPE sheathed Aluminium, steel armoured HT power cable as per IS 7098. The cable shall be laid on trench / cable trays / Hume pipes / Buried under ground. Rate to exclude cost of trays, pipes and supporting items but including necessary cable clamps.( 3 C x 120 Sq.mm)conforming to IS 1538. with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

ELECTRICAL WORKS Design, Manufacture, Supply, Installation, Testing and 30 days continuous , successful trial running& commissioning of integrated cubicle type, dead front, extensible, sheet steel PMCC Panel (For Intake Well Site) suitable for 415V, 3 Phase, 4 Wire, 50 Hz, AC supply system in compartmentalized design. The panel shall be fabricated out of 2mm CRCA sheet steel and shall be treated with anticorrosive process before painting and painted with 2 coats of approved colour paint over a coat of primer. The panel shall be complete with suitable capacity extensible type TPN aluminium alloy bus bars of high conductivity, DMC/SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 sec, solid connections from main bus bar to switch gears with required size of Al. bus bars, control wiring with copper conductor, cable alleys, cable gland plate, including providing the following switch gears with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Supply, delivery of 2 pole structure materials with suitable Size RSJ along with all structure material are as under.(For 11 KV Incomer)with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Construction of transformer plinth with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Chain link fencing with gate including the TNEB 2 poles Spreading of materials as per CEIG requirements with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Transformer yard earthing using copper flat and TWIN earthing as per IS (For 500 KVA Transformer sub station)with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Transformer & sub station erection charges with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Providing and Fixing,Supply, Installation, Testing and 30 days continuous , successful trial running & commissioning full complete set of Instruments such as Low Level Switch, Dry Run Sensor, etc., for switching off of all the running pumps in case of low water level in the intake well or dry running of the pumps, etc., complete with necessary interlocking wiring in the electrical panel, with cost and supply of all materials, labour, T&P, taxes, tollage, royalties, etc. all complete but Excluding GST as directed by Engineer-in-charge.

Supply & Laying of 1.1 kV grade XLPE insulated, XLPE sheathed Aluminium, steel armoured power cable as per IS 7098. The cable shall be laid on trench / cable trays / Hume pipes / Buried under ground. Rate to exclude cost of trays, pipes and supporting items but including necessary cable clamps. including cost and supply of all materials, labour, T&P, all taxes, transportation charges etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

From Transformer to PMCC - 3.5 C x 300 Sq.mm :3 Runs of 300 Sqmm Cable for each incoming

From PMCC to LDB / PDB - 4 C x 10 Sq.mm

For Street Light & Plant Lights - 4C x 6 Sq.mm

Supplying and making end termination with brass compression gland for following sizes of XLPE insulated and PVC sheathed aluminium conductor cable of 1.1 KV grade as required.including cost and supply of all materials, labour, T&P, all taxes, transportation charges etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

3.5 C x 300 Sq.mm

3 C x 150 Sq.mm

4C x 10 Sq.mm

4C x 6 Sq.mm

Supplying and making end termination with Al lugs for following sizes of aluminium conductor cable of 1.1 KV grade as required.including cost and supply of all materials, labour, T&P, all taxes, transportation charges etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Supply & Installation of following sizes of Factory made Pre galvanized iron sheet perforated cable trays made out of 2mm thick sheet. The cable tray shall be supplied as specified with necessary supports, all accessories like bend, Tees etc. manufactured at the manufacturers workshop as per Drawing/ as per the requirement of site condition. The tray should be provided with adequate supports, the distance between supports shall not be more than 1.2 to 1.5 meter. Coupler plate & galvanized hardware should be used to join the cable tray section. Earthing continuity shall be ensured at each joint.including cost and supply of all materials, labour, T&P, all taxes, transportation charges, all consummables,tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

600mm Wide x 50mm Deep

300mm Wide x 50mm Deep

Providing and Fixing full complete set of Safety Equipment required for the installation as per the CEIG requirements consisting of danger plates, Fire Extinguishers, safety charts, rubber mats, first aid box, gloves, apron,facesleeve etc.(P.P.E), including cost and supply of all materials, labour, T&P, all taxes, transportation charges, tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Earthing as per the ISI specification with earth electrode of 2.1 mtr. Class 'B' GI pipe of dia not less than 40 mm, with copper earth plate of size 125mmx 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD-233) including cost and supply of all materials, labour, T&P, all taxes, transportation charges, tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Supply and run of 50mmX6mm GI strip including cost of all accessories and labour charges , T&P, all taxes, transportation charges, tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Supply and fixing of Horizontal type 4way TPN MCB Distribution Board in sheet steel enclosure with 64A/32A Four Pole MCB isolator as incoming and 12 Nos., 6A to 32A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCB DB, MCB Isolator and MCBs should be with ISI mark, standard (SD - 179) including cost and supply of all materials, labour, T&P, all taxes, transportation charges, tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Wiring with 2 x 1.5 Sqmm PVC insulated SC unsheathed copper conductor of 1100V. grade in suitable PVC Pipe concealed in wall / ceiling with PVC accessories with Latest model, module type plate switches for concealed Light / Fan Point / Socket. (DATA-K) including cost and supply of all materials, labour, T&P, all taxes, transportation charges, tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Supply, Installation, Testing and 1 month trial running & commissioning of point wiring 16A rating (1 Point with 1 Control switch) using 2 x 2.5 + 1 R x 1.5 sqmm PVC insulated ZHFR multi stranded 1100V grade copper wires drawn in 25mm dia MS conduit including all conduit accessories such as bends, Junction boxes etc. The control switches shall be 16A MCB, of approved make integral GI box with clear earthing facility.including cost and supply of all materials, labour, T&P, all taxes, transportation charges,all consummables, tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Supply, Installation, Testing,30 days continuous , successful trial running and Commissioning of Power Circuit wiring using 2 x 2.5 + 1 R x 1.5sqmm PVC insulated ZHFR multi stranded 1100V grade copper wires drawn in 20mm dia MS conduit including all conduit accessories such as bends, Junction boxes including cost and supply of all materials, labour, T&P, all taxes, transportation charges, tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Supply and Fixing of 2x20W 4' Long surface mounting type LED Tube light complete with mounting support, wiring, and minor consumable material, including cost and supply of all materials, labour, T&P, all taxes, transportation charges, tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Supply and Installation of 48" (1200mm) Sweep ISI mark Ceiling Fan as per IS 374 - 1979, with double ball bearings, power input not more than 50W, air delivery more than 200 cubic meter/min but without Regulator.including cost and supply of all materials, labour, T&P, all taxes, transportation charges, tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Supply and Installation of 24" (600mm), 900 RPM Heavy duty exhaust fan with metallic blades with ISI Mark including cost and supply of all materials, labour, T&P, all taxes, transportation charges, tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Supply and Fixing of 65mm (2 1/2") GI Pipe class B of 6 mtr with 300mm x 300 mm x 6mm M.S. base plate duly welded, with concreting, with construction of masonry pedestal, with suitable SMC Box to house 16 A control switch 16 A Fuse unit (500 V ) etc. with suitable angle iron frame work, with door and with lock and key arrangements and with supply and fixing of 120 W LED street light fitting with integrated driver, 1 mtr of 32mm dia GI pipe (Class B) arm pipe, complete with necessary clamp on the post with PVC unsheathed lead's with painting of suitable colour. (DATA - A) including cost and supply of all materials, labour, T&P, all taxes, transportation charges, tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Supply and Fixing of 65mm (2 1/2") GI Pipe class B of 6 mtr with 300mm x 300 mm x 6mm M.S. base plate duly welded, with concreting, with construction of masonry pedestal, with suitable SMC Box to house 16 A control switch 16 A Fuse unit (500 V ) etc. with suitable angle iron frame work, with door and with lock and key arrangements and with supply and fixing of 120 W LED street light fitting with integrated driver, 1 mtr of 32mm dia GI pipe (Class B) arm pipe, complete with necessary clamp on the post with PVC unsheathed lead's with painting of suitable colour. (DATA - A) as per direction of Engineer -in -charge(For Plant Light Installed on Tank Tops with necessary Anchor Fasteners) including cost and supply of all materials, labour, T&P, all taxes, transportation charges, tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Execution of works other than those listed above, which are required for making the electrical installation complete in all respects for obtaining safety certificate of CEIG. including cost and supply of all materials, labour, T&P, all taxes, transportation charges, tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Supply, Installation, Testing and 30 days continuous , successful trial running & commissioning of 120 KVAR APFC panel Supply, unloading, installation, testing and commissioning of floor mounting cubicle type LT switch board fabricated out of 16 Swg CRCA and powder coated to Siemens gray shade. The panel will be equipped with following. Bus bar chamber consisting of TP and N bus bars rated 200A made of electrolytic quality aluminium supported on SMC supports. The incomer shall be 200A TP MCCB, 25 ka with thermal over load and magnetic short circuit releases The capacitor bank shall be 30x4 (120 KVAR ) MPPH controlled by MCBs and adequate rating air break capacitor duty Contactors and with LED type on/off lamps. , control fuses and auxiliary relays. The APFC relay shall be 8-stage microprocessor controlled type. There shall be an earth bus at the bottom of the panel made of 25x3mm copper with provision to connect to external earth bus. All the MCBs and other component frames shall be double earthed with suitable size copper conductor and connected to this earth bus The cable entry shall be from bottom. A detachable cable gland plate shall be provided at the bottom of the panel.30 KVAR capacitors shall be controlled by 64A TP MCB. All contactors shall be capacitor duty including cost and supply of all materials, all consummables ,labour, T&P, all taxes, transportation charges, tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

Supply, delivery and erection, Installation, Testing and 30 days continuous , successful trial running & commissioning of 250 KVA 3 Phase Air/Liquid Cooled 240 / 415V + 5% 0.80 PF at 50 Hertz containerized AC Diesel Generator set rated for continuous running with an over load provision of 10% for a period not exceeding one hour for every eleven hours at full load. The Diesel Genset shall comprise diesel engine as per relevant IS Codes, CPCB Norms and Standards at 1500RPM with standard accessories and the generator with suitable AMF control panel including supply, delivery, laying and jointing of relevant cable, Wearing earthing & Meggering the electrical equipment, erection, testing and commissioning vide detailed specifications and terms.including cost and supply of all materials, labour, T&P, all taxes, transportation charges,all consummables, tollage, royalties etc. complete but excluding cost of GST as per direction of Engineer-in- charge.

FOR 2 YEAR OPERATION & MAINTENANCE (O&M) (NB: O& M Starts from the last day of completion of successful trial run ) Engaging of Maintenance Engineer - Mechanical graduate Engineer with more than 5 Years experience .(Excluding GST)

Engaging of Maintenance Engineer - Electrical graduate Engineer with more than 5 Years experience .(Excluding GST)

Plant Operator with more than 3 Years experience(1 Person per Shift)(Excluding GST)

Engaging of Skilled Manpower(Excluding GST)

Engaging of Un Skilled Manpower(Excluding GST)

AMC & Fuel Expenses for DG (Excluding GST) (Payment will be made as per production of supporting documents.)

CMRGS INFRASTRUCTURE PROJECTS LIMITED

SANJAY KUMAR UPADHYAY

Ms Gangadhar Jena

SVS PROJECTS

SWACH ENVIRONMENT PRIVATE LIMITED

MASTEK ENGINEERING PRIVATE LIMITED