REPAIR/MAINTENANCE AND PAINTING OF STEEL FURNITURE UNDER GE(I) KANPUR

Amount

Charpoy GI pipe (FD-220) S & F following components of Charpoy GI pipe including dismantling unservicable one all as specified and as directed. (a) Long rail made of 32 mm dia GI Tubing medium grade ISI mark 1.88 mtr long, threaded at both ends and fixing to 3 way 32 mm dia GI elbow of charpoy. (Make : Jindal/Bansal/Tata)

3 way 32 mm dia GI elbow ISI marked

Check nuts of 32 mm dia

Conversion of 32 mm dia long rail obtained from item No 1 above into two numbers short rail after cutting and threading both ends and fixing to 3 way 32 mm dia existing elbow.

Conversion of 32 mm dia short rail obtained from item No 4 above into two numbers leg including fixing to 3 way 32 mm dia after one end threaded .

Removing old unserviceable/rusted MS Plate and S/F new MS Plate of size 900mmx40mm x 5mm duly painted with black colour after applying red oxide after making two Nos holes.

M & L for removing old U/S plywood and S/F New 12 mm BWR phenol bonded commercial plywood of size 2020 mm x 900 mm including fixing of plywood with new 12 Nos Nut and bolts (75mmx6).Necessary reassembling the components as where required to fixing components and tighten the charpoy frame to make original shape of charpoy as per drg before fixing the ply top. Rest all as per directed by Engr-in-Charge. Make of plywood - Archid Ply/Green ply/Century.

Almirah Steel med Steel/Almirah Med 1/2 H 1/2S (FD 67/1032) S & F following components of Almirah steel med including dismantling unservicable one all as specified and as directed (a) Lock with duplicate keys (Make of Lock- LICO/RINA)

(b) Handle 100 mm size chromium plated

(c) 3 way locking device with necessary fittings and painted with two coats of synthetic enamel paint of olive green/smoke grey shade of approved quality over a coat of primer.

(d) Supply and fix leg made of 1mm thick CRCA sheet duly welded/riveted and painted with two coats of synthetic emamel paint of olive green/smoke grey shade of approved quality over a coat of primer.

(e) Supply and fix door shutters made of 1mm thick CRCA sheet including chromium plated steel handle 100mm size -01 No, 3 way locking device with lock with duplicate keys- 01 No, key hole and painting with one coat of synthetic enamel paint of olive green/smoke grey/red or any shade as approved over a coat of primer both inside and outside after preparation of surface complete all as specified and shown on drawing. (Note for steel painting;- All steel surface shall be done with spray painting) (Make of Lock-LICO/RINA)

(f) Supply and fix shelves made of 1mm thick CRCA sheet welded/riveted and painted with two coats of synthetic emamel paint of olive green/smoke grey/any shade as approved over a coat of primer.

(g) Preparation of old painted steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty wherever required and applying two coats of (spray painting)synthetic enamel paint of olive green/Smoke Grey/ any shade of approved quality both inside and outside including dents/bends complete all as specified and as directed.

Almirah steel large/ Almirah steel large 1/2H 1/2S (FD-67/1031) S & F following components of Almirah steel med including dismantling unservicable one all as specified and as directed (a) Lock duplicate keys (Make of Lock-LICO/RINA)

(b) Handle 100 mm size chromium plated

(c) 3 way locking device with necessary fittings and painted with two coats of synthetic enamel paint of olive green/smoke grey/ any shade as approved over a coat of primer.

(d) Supply and fix leg made of 1mm thick CRCA sheet duly welded/riveted and painted with two coats of synthetic emamel paint of olive green/smoke grey/ any shadeas approved over a coat of primer.

(e) Supply and fix door shutters made of 1mm thick CRCA sheet including chromium plated steel handle 100mm size -01 No, 3 way locking device with lock with duplicate keys- 01 No, key hole and painting with two coats of synthetic enamel paint of olive green/smoke grey/ any shade as approved over a coat of primer both inside and outside after preparation of surface complete all as specified and shown on drawing (Make of Lock-LICO/RINA)

(f) Supply and fix shelves made of 1mm thick CRCA sheet welded/riveted and painted with two coats of synthetic emamel paint of olive green/smoke grey/ any shade of approved quality over a coat of primer.

(g) Preparation of old painted steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty primer wherever required and applying two coats of synthetic enamel paint of olive green/Smoke Grey/ any shade as approved both inside and outside complete including dents/bends complete all as specified and as directed.

Locker Bed Side steel (FD-1029) S & F following components of Locker steel including dismantling unservicable one all as specified and as directed. (a) Handle 100 mm size chromium plated

(b) Hasp & staple 100mm chromium plated

(c) Supply and fix leg made of 1mm thick CRCA sheet duly welded/riveted and painted with two coats of synthetic emamel paint of olive green/smoke grey/ any shade of approved quality over a coat of primer.

(d) S & F door shutters made of 1mm thick CRCA sheet including chromium plated handle 100mm size -01 No, chromium plated hasp & stapple of approved quality and painting with two coats of synthetic enamel paint of olive green/smoke grey/ any shade of approved quality over a coat of primer both inside and outside after preparation of surface complete all as specified and as directed.

(e) S & F new curtain rod SS of size 20mm dia of 1.6mm wall thickness of locker steel

(f) Preparation of old painted steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty wherever required and applying two coats of synthetic enamel paint of olive green shade/Smoke Grey/ any shade of approved quality both inside and outside complete including dents/bends complete all as specified and as directed.

Table dining 900x 900 mm steel (FD-1009) S & F following components of Table dinning 900x900 mm steel including dismantling unservicable one all as specified and as directed. (a) Leg/stiffener 25 x 25 x 1.6mm thick MS squire pipe duly welded to the frame including minor repairs to the table and painting the replaced portion.

(b) Table top made of pre-laminated MDF board exterior grade 18mm thick post-formed with 0.6 mm thick laminated in Mohigni/Walnut colour/shade as approved by Engr-in-Charge with 2 mm thick PVC edging of Make : Rehau/Pegasus/Kynes shall be fixed on two sides it complete with strong bonded chemical adhesive through hot pressed machine all as specified in drg and as directed by Engr-in-Charge.

(c) Preparation of the old painted steel surfaces by scraping with emery paper, cleaning and applying two coats of synthetic enamel paint of olive green shade of approved quality.

(d) PVC shoe

Table office officer/clerk steel (FD-84/1003,1004 ) S & F following components of Table office/clerk steel including dismantling unservicable one all as specified and as directed. (a) Drawer made of 1mm CRCA sheet including painting with synthetic enamel paint of olive green shade of approved quality over a coat of primer both inside and outside including preparation of surfaces and repairing inter locking system and providing new lock 6 lever to top drawer.

(b) Leg/stiffener 25 x 25 x 1.6mm thick MS square pipe duly welded to the frame and painted with two coat of synthetic enamel paint over a coat of primer.

(c) Lock with duplicate keys(Make- Lico/Rina)

(d) Complete box comprising of 03 drawers made of 1mm CRCA sheet including locking arrangement/accessories and painting with two coats of synthetic enamel paint of olive green shade of approved quality over a coat of primer/putty ofTable office Officer/Clerk Steel.

(e)Top of table office officer steel shall be made of pre-laminated MDF board exterior grade 18mm thick post-formed with 0.6 mm thick laminated in Mohigni/Walnut colour/shade as approved by Engr-in-Charge with 2 mm thick PVC edging of Make : Rehau/Pegasus/Kynes shall be fixed on two sides it complete with strong bonded chemical adhesive through hot pressed machine all as specified in drg and as directed by Engr-in-Charge.

(f))Top of Table Office Clerk Steel shall be made of pre-laminated MDF board exterior grade 18mm thick post-formed with 0.6 mm thick laminated in Mohigni/Walnut colour/shade as approved by Engr-in-Charge with 2 mm thick PVC edging of Make : Rehau/Pegasus/Kynes shall be fixed on two sides it complete with strong bonded chemical adhesive through hot pressed machine all as specified in drg and as directed by Engr-in-Charge

(g) PVC shoe

(h) Preparation of old painted steel sufaces by scraping with emary paper, cleaning, dedusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying two coats of synthetic enamel paint of olive green/Smoke Grey/any shade as approved both inside and outside complete all as specified and as directed for Table office officer steel.

(j) Preparation of old painted steel sufaces by scraping with emary paper, cleaning, dedusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying two coats of synthetic enamel paint of olive green/Smoke Grey/ any shade of approved both inside and outside complete all as specified and as directed for Table office clerk Steel.

Chair steel tubular with/ without arms (FD-75 M) S & F following components of Chair steel tubular with/ without arms made out of shisham wood french polished duly plastic canned in 'Godrej' pattern with plastic cane 2mm width and borders with 4mm wide plastic cane fixed with screws 4 Nos and nuts to the chair frame complete all as per drawing. including dismantling unservicable one all as specified and as directed. (a) Seat frame

(b) Back frame

(c) Handle made of shisham wood duly french polished and fixed to the chair tubular with arms with screws of suitable size.

(d) MS Flat size 25 x 25 x 4mm thick welded at corner at bottom of the seat only to support and screwed with the seat .

(e) Preparation of surfaces and painting with two coats of synthetic enamel paint OG colour to chair steel tubular with/without arms including 4 Nos of PVC bushes to the bottom of the chair frame and 2 Nos of PVC caps on the top of the frame.

Table Dining ORs (FD-165) Removing of old unserviceable top of table dining ORs and S & F new top made of pre-laminated MDF board exterior grade 18mm thick post-formed with 0.6 mm thick laminated in Mohigni/Walnut colour/shade as approved by Engr-in-Charge with 2 mm thick PVC edging of Make : Rehau/Pegasus/Kynes shall be fixed on two sides it complete with strong bonded chemical adhesive through hot pressed machine all as specified in drg and as directed by Engr-in-Charge.

Taking out of unserviceable stiffner and S & F new stiffner of mild steel square tube as per existing shape and size of Table dining ORs.

Preparation of old painted steel sufaces of table dining ORs by scraping with emery paper, cleaning, dusting and making the surfaces smooth and applying two coats of olive green/black colur/shade of approved synthetic enamel paint including fixing of four Nos of PVC shoes to each leg.

Chair Verandah(FD-256) Preparation of steel tubular frame surfaces with emery paper and applying two coats of synthetic enamel paint of white colour of approved quality and recaning the chair fully both seat and back with new plastic cane, white, half round of size 4mm wide including providing new suitable 04 Nos PVC shoes to the each leg of approved quality.

Teapoy Varandah (FD-255/383) Preparation of old painted steel sufaces by scraping with emery paper, cleaning, dusting and making the surfaces smooth and applying two coats of white synthetic enamel paint including four Nos PVC shoes.

Removing old U/s table top and S/F top made of pre-laminated MDF board exterior grade 18mm thick post-formed with 0.6 mm thick laminated in Mohigni/Walnut colour/shade as approved by Engr-in-Charge with 2 mm thick PVC edging of Make : Rehau/Pegasus/Kynes shall be fixed on two sides it complete with strong bonded chemical adhesive through hot pressed machine all as specified in drg and as directed by Engr-in-Charge.

Table 3'x2' with/without drawer steel FD-283,1008,223,310,1007 S & F following components of Table dinning 900x900 mm steel including dismantling unservicable one all as specified and as directed. (a) Leg/stiffener 25 x 25 x 1.6mm thick MS square pipe duly welded to the frame including minor repairs to the table and painting the replaced portion.

(b) Table top made of pre-laminated MDF board exterior grade 18mm thick post-formed with 0.6 mm thick laminated in Mohigni/Walnut colour/shade as approved by Engr-in-Charge with 2 mm thick PVC edging of Make : Rehau/Pegasus/Kynes shall be fixed on two sides it complete with strong bonded chemical adhesive through hot pressed machine all as specified in drg and as directed by Engr-in-Charge.

(c ) Taking out of unserviceable drawer and S & F of new drawer of mild steel square tube 25mm as per existing shape and size complete all as per Drg.

(c) Preparation of the old painted steel surfaces by scraping with emery paper, cleaning and applying one coat of synthetic enamel paint of olive green/smoke grey/ any shade of approved quality.

(d) PVC shoe

Chair visitors /Chair Writing MAP Trade Pattern (a) Chair visitors of different Make and Model (SEAT & BACK) and re-upholstering with new tapestry/ (approved quality) including dismantling of old one complete all as specified and dircted.

(b) Supply and Fix New SEAT & back (Cushion,tapestry & ply) 50mm thick cushion complete (approved quality) of different make and model including dismantling of old one complete all as specified and dircted.

(c) Supply and fix handle of chair visitors of (soft/PV) suitable size and design as per original Pattern of different Make and Model including dismantling of old one complete all as specified and as directed.

(d) M&L for painting two coats of synthetic enamel paint to be match as per old/existing colure in Iron frame of Chair visitor of various Make & Models including scraping old painted/rusted parts by emery paper all as specified and as directed.

Chair Revolving executives High Back TP Trade Pattern (a) Chair Revolving of different Make and Model (SEAT & BACK) and re-upholstering with new tapestry/ (approved quality) including dismantling of old one complete all as specified and dircted.

(b) Supply and Fix New SEAT & back (Cushion,tapestry & ply) 50mm thick cushion complete (approved quality) of different make and model including dismantling of old one complete all as specified and dircted.

(c) Supply and Fix New high quality caster wheel as per sample approved by Engr-in-Charge for chair revolving high back including dismantling of old one complete all as specified and dircted.

(d) Supply and Fix New hydraulic as per sample approved by Engr-in-Charge for chair revolving high back including dismantling of old one complete all as specified and dircted.

(e) Supply and Fix New seat base plate as per sample approved by Engr-in-Charge for chair revolving high back including dismantling of old one complete all as specified and dircted.

(f) Supply and fix handle of chair revolving high back of (soft/PV) suitable size and design as per original Pattern of different Make and Model including dismantling of old one complete all as specified and as directed.

(g) M&L for painting two coats of synthetic enamel paint to be match as per old/existing colure in Iron frame of Chair revolving high back of various Make & Models including scraping old painted/rusted parts by emery paper all as specified and as directed.

Desk for student Taking out and removing the old damaged/broken top of desk from its position and s &f new top in the same position as per existing shape and size made out of 18/19mm thk pre-laminated MDF board of apporved shade along with PVC edging all around the top complete all as shown on drg. (Make: Green ply/Archid ply/Century Ply )

Taking out and removing the old damaged/broken bottom of desk from its position and s &f new top in the same position as per existing shape and size made out of 12mm thk pre-laminated MDF apporved shade along with PVC edging all around the top complete all as shown on drg. (Make: Green ply/Archid ply/Century Ply )

Removing old unserviceable PVC shoes from leg of Desk steel and S&F new PVC shoes of approved quality complete all as specified and as directed.

Taking out and removing the old damaged/broken front portion of desk from its position and s&f new portion in the same position made out of 12mm thk pre-laminated MDF apporved shade along with PVC edging all around the top complete all as shown on drg. (Make: Green ply/Archid ply/Century Ply )

Taking out and removing the old damaged/broken side position of desk from its position and s&f new partition in the same position made out of18/19mm thick pre-laminated MDF apporved shade along with PVC edging all around the top complete all as shown on drg. (Make: Green ply/Archid ply/Century Ply )

Taking out and removing the old damaged/broken middle partition of desk from its position and s&f new partition in the same position made out of18/19mm pre-laminated MDF apporved shade along with PVC edging all around the top complete all as shown on drg. (Make: Green ply/Archid ply/Century Ply )

Taking out and removing the old damaged/broken bench top of desk for student from its position and s &f new bench top of existing shape and size made out of 18/19mm thk pre-laminated MDF board of apporved shade along with PVC edging all around the top complete all as shown on drg. (Make: Green ply/Archid ply/Century Ply )

M & L for two coats of synthetic enamel paint of apporved shade steel surface shall be painted over a coat of primer after preparation of surfce and all as specified and as directed.

M & L for spot welding of broken steel frame of desk complete all as specified and as directed.(Note; Each sprt welding shall be not exc 5cm in length and meterial to be welded not exc 2mm in thickness.FD-124

Preparation of the old painted steel surfaces by scraping with emery paper, cleaning dusting and make surface smooth, filling holes with putty wehrever required and ng two coats of synthetic enamel paint of olive green/black/smoke grade/shade as approved by Engineer- Charge for Trestle room steel

All as per item Ser No 27 above but Rack Six tier steel/Rack Steel 1800x1900x760

All as per item Ser No 27 above but Rack side steel 3/4 drawer

All as per item Ser No 27 above but Book Case steel

All as per item Ser No 27 above but Shoe Rack Steel

All as per item Ser No 27 above but Book shelf open large steel

All as per item Ser No 27 above but Stool Steel 2' high

Vinayak Distributors

ANAND FURNITURE

S B ENTERPRISES

Star Sofa House