ADDN / ALTN AND SPL REPAIRS OF BLDG NO. P-49 CoE (ME) ANNEXE AND PROVN OF CHAIN LINK FANCING AND WATERING ARRANGEMENT FOR HOCKEY GROUNG AND PROVN OF BUILT IN CUP BOARDS IN AGE OFFICE (P-83) AT INS SHIVAJI LONAVLA

Amount

Excavating over areas, n exc 1.5m deep and getting out in hard /dense soil

M & L for PCC 1:4:8 type D2 (using 40 mm graded aggregae in foundation and mass concrete.

M & L for M 40 (using 20 mm gradual aggregate) reinforced cement concrete (design mix) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete Note : Design mix concerete should be thorugh RMC only

-ditto- all as per item no 3 above but as in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses Note : Design mix concrete should be thorugh RMC only

M & L for M 40 (using 20 mm gradual aggregate) reinforced cement concrete (design mix) in slab supported on walls beams and columns in floors,roofs landing,landings,balconies canopies deck slabs and shelves and the like etc. Note : Design mix concerete should supply thorough RMC only

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter surface for circular surface of concrete finished smooth

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter for circular surface of concrete finished smooth

Formwork to soffit of flat suspended slabs such as roof slabs florr slabs landings and similar work not exceeding 200 mm thick horizontal or slopping surface of concrete finished smooth

S & F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe 410 Gde 250

Ditto as item no above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

S & F mild steel round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe 410 Gde 250

M & L 15mm thick rendering on fair faces of brick wk or concrete surface in CM 1:3 with using liquid water proofing compound 2% by wrought all as specified (WPC paid separately).

S & F Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe Fe 290 Gde E-165

S&F MS plate 8mm thick (Plain or chequred) channels, and counter sank) forming holes, with out any attachment FE-410-W (Code E - 250) Quality - B

M&L for Preparing new steel surface any description and applying two coat of synthetic enamel paint over a coat of red oxide. .

Supply Liquid Water proofing compound

Removing excavated material exc. 50m and n exc 250m, depositing where directed at a level n exc. 1.5m above the starting point

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

M&L for preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash complete all as specified and directed

M & L for hardcore of gauge n exc 63 deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface

M&L for 75 mm thick plinth protection of cement concrete type C-2, 1:3:6 (40 mm garded aggrefate) complete all as specified and directed.

S&F PVC water bars 150 mm width and 6 mm thick along with the construction joints

S&F Rotational moulded polyethylene water storage tanks, 2000 ltr capacity(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part -I

S&F 25 mm bore Ball brass valve high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule and fixed and complete and directed by engr in charge.

Taking down chowkats with shutters( without taking off shutters from the frame) exc1.5 sqm and n exc 4 Sqm each

S&F aluminium powder coated of any colour (thickness of powder coating not less than 50 micron), in frame for doors , windows, ventilators, partition wall etc. with one or more rebates, shutters, grills including joining cleat glazing clips for fixing etc. complete all as specified. Note : (i) The gap of frame alround Jamb and cill should be sealed with using silicon Gel at the rate of 0.05 lit/m.

S&F aluminium powder coated (three track) sliding typeand fixed type window shutters of any colour (thickness of powder coating not less than 50 micron) shutters of Aluminium sections 39.4 x 17.7 x 1.2 mm without sash bars including necessary jointing cleats , glazing clips, rubber packing, anodised snap beading ,screws aluminium fitting handles ,locking arrangement etc, excluding 4.00 mm thick sheet glass for glazed shutters and stainless steel wire cloth 0.36mm nominal dia of wire and avarage width of aperature 1.40mm complete all as specified and as directed. Note:(i) the window opening shall be provided with three shutters of equal width.

S&F Sheet glass, of 4.00mm thick ordinary quality and glazing with al frame exc 0.5 sqm in each pane

S&F Sheet glass, of 4.00mm thick ordinary quality and glazing with al frame n.exc 0.5 sqm in each pane

S&F stainless steel wire cloth 0.36mm nominal dia of wire and avarage width of aperature 1040mm and fixed with aluminium frame complete all as specified and directed by engr in charge

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each and refixing in the same opening after necessary repair complete.

Dismantling mild steel or wrought iron work of any description not otherwise provided for.

Demolition of brick work /stone masonry built in cement mortar incl all quions, arches pillars etc but excl ashalar facing dressed stone work and precast cocrete articles

M&L for Walling of random rubble, uncoursed well bonded, bedded and solidly hearted built in CM 1:6 complete all as specified

Hammer dressing with maximum depression on face from straight edge held against the dressed surface n exc 40mm over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses complete all as specified

M&L for 75mm thick Moorum/Red bajiri, spread, rolled and consolidated to gradient and camber required all as specified and directed.,

M&L 150mm thick PCC, type B-2 1:2:4 (40mm graded stone aggregate) as in pavement/roads and finishing surfaces of concrete by brooming complete all as specified and directed by Engr-in-charge.

S&F steel rolling shutters of 1.25 mm thick laths without ball bearing as specified including top cover,anchoring rod ,guide channels , hasp and staples and one shop coat of primer erected in position as indicated complete but gear operated with bevel gear box and crank handle all as specified and directed by Engr in charge.

S&F brickwork with sub-class 'B' bricks, straight or curved on plan exc 6m mean radius, built in Cement mortar 1:6.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level)

M&L 50mm thick PCC, type B-1 1:2:4 (20mm graded stone aggregate) as in flooring and finishing surfaces of concrete complete all as specified and directed by Engr-in-charge.

M&L for 20mm wear proof toppings as specified(incorporating an approved metalic floor hardner) laid on concrete floors and pavings (as per manufactures instruction) and finished even and smooth all specified and directed by Engr in Charge.

Supply only Metalic floor hardner for wear topping over concrete surfaces.

M & L 15mm thick rendering on fair faces of brick wk/ Stone masonry or concrete surface in CM 1:4 finished even and smooth (without using extra cement) all specified and directed by Engr in Charge.

M & L 15mm thick rendering on other than fair faces of brick wk/ Stone masonry or concrete surface in CM 1:6 finished even and smooth (without using extra cement) all specified and directed by Engr in Charge.

M&L for Preparing newely plastered surface and primng with alkali resistant priming paint and applying 2 coats of antifungal weather proof paint exterior grade emulsion paint complete all as specified and as directed.

M&L for preparation of newly and untreated surfaces of walls and applying two coats of plastic emulsion paint on one coat of primer complete all as specified and directed

M&L for preparation of old painted surfaces of walls and applying two coats of plastic emulsion paint on one coat of prime complete all as specified and directed

M&L for preparation of plastered or unplastered old decorated surfaces of ceiling and applying two coats of white wash complete all as specified and directed

Excavating over areas, exc 1.5m and nexc 3.00mtr deep and getting out in any type of soil/ sott intregrated Rock

Excavation in trenches n.exc 1.5m wide n.exc 1.5m deep for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 Sqm on plan and n.exc 1.5m depth and getting out in hard dense soil

M&L Moorum/Red bajiri filling in floors or pavings, laid in layers n.exc 15cm thick spread levelled and rammed including watering complete all as specified and directed.,

M&L for Brickwork with Modular bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 in narrow widths including Cutting out bricks/stone, forming toothing for, and bonding new into old brickwork /stone masonry

S&F Mild steel 1.25mm plain black sheet in gates or similar works cut to size holes punched incl screws nails fixed to steel frame welded incl steel tower bolts and etc complete

S&F Rolled mild steel section in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc quality conforming to Fe 410-W (Gde E250) quality-A.

S&F wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165

M&L for providing cement concrete type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) as in roof kerbs or mud stops rounded or chamferred on edges mass concrete

100 mm thick PCC (1:2:4) type B-2 using 40 mm graded stone aggregate as in sub base as specified and directed.

M&L for 40 mm thk PCC 1:2:4 type B-1 using20mm graded agg as in flooring finished even and smooth with using extra cement complete all as specified and directed.

S&F CI vent pipe 150mm dia in any length with or without ears with cement joints fixed in floor /slab fixed by Fi clamp and nut and bolt,covered mouth with 63 G wire mesh etc complete all as specified and as directed.

S&F CI bend 150 mm bore fixing with ci vent pipe complete all as specified and as directed.

Excavating in post holes (or similar holes) each n. exc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n. exc 50m and making good surface in hard dense soil

M&L for providing cement concrete type C-2, 1:3:6 (using 40mm graded crushed stone aggregate) as in foundation, bed blocks,filling and mass concrete

S&Fmild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete drilled for fixing of steel sheeting or other covering, doors,f etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete Fe-290 (gde E-165).

Supply only chain link fencing, MS galvanised of any size and type complete all as specified and as directed by Engr in Charge.

Fixing only chain lnk fencing including line wires, any mesh, size, any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified and as directed Note : chain link fencing shall be measured and paid separately as " supply only"

S&F Mild steel round bars 10mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete

S&F fixed 5 to 10 mm dia Mild steel screws bolts(Machine made)with hexagonal or square heads at one end and screwed both ends ,each screwed end to be fitted with washers and one hexagonal or squre nut, lentg of bolt exc 5cm and n.exc 10cm long. With washers.

Surface excavation n.exc(not exceeding) 30 cmdeep and averaging 15cmdeep and getting out hard dense soil.

M&L cement concrete 1;4:8 type D2 (40mm aggregate) 75 mm thick as in sub base

M&L for 50 mm sand cushioning under interlocking in floors including watering and consolidation.

M&L for Machine pressed precast concrete interlocking paver block conforming to IS 15658-2006 of 60 mm thickness, M-35 grade with approved colour design & pattern laying through vibratory compaction by using plate vibrator, finishing and sweeping extra sand complete all as specified and directed.

M&L for filleting in any position and to any shape in cement mortar 1:4 including all mitres, stops etc section of fillet exc 25 but n.exc 50 Sqcm

M&L for non skid ceramic white tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete.

M&L for white glazed ceramic tiles in vertical surface 300mmX450mmx 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick back coat in CM 1:4 complete all as specified and directed.

M&L for 20 to 25 mm thick cudappa stone work in single piece (table rubbed and polished) in steps, floors, slabs, complete all as specified and as directed.

S&F second class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified

S&F 75mm butt hinges, stainless steel medium weight fixed with stainless steel screws.

S&F aluminium handles cast type anodised 125mm size.

S&F aluminium anodised barrel tower bolts of extruded section and fixed 150 mm size.

S&F aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of sextruded sections or cast aluminium alloy and fixed 250mm length.

S & F Continuous (piano) hinges 30mm wide mild steel, bright finish or electrogalvanised.

S&F150 mm Hasp and staple, safety type brass with mild steel hinge pin including bolt to hinge plate and fixed with screws.

S&F Bands, straps, ; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe 290 Gde E-165

Providing, cement concrete TypeB0 1:2:4 (12.5mm graded aggregate bed plates and the like including weathering, slightly rounded or chamfered angles and throating, as directed

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer

M&L for Preparing newly plastered surface and primng with alkali resistant priming paint and applying 2 coats of oil bound distemper on walls over 3 mm thk wall care putty

M & L for plain fillets, square, rectangular or triangular in section clean sawn, secured with nails 2nd class hard wood exc 13 and n.exc 25 sqcm complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan in any radius in half brick thick walls built in cement mortar 1:4, complete all as specified and directed

M&L for prelaminated particle board 18/19mm thick, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination as in shelves of cup boards etc., rebated or flat edged including 6mm thick teak wood lipping on exposed edge, supported on teak wood wrought fillet of size not less than 25x25mm on three sides.

M&L RCC 1:2:4 Type B1(nominal mix) as in slabs supporting on walls beams and columns in floors roofs, landings,balconies,canopies,deck slabs and in shelves and the likes.(Reinforcement shall be measured & paid separately).

Cutting Existing 200/250mm bore CI water mains and inserting ferrules of size 50mm dia for taking branch connection including fittings all as specified and directed.

Supply and lay tube light grade 50mm dia galvanized “Medium class with all fittings and fixed complete to walls and ceilings or laid in floors,” all as specified and directed.

Supply and fix Straight plain brass ferrules 50mm dia or connecting screws) screwed both ends and fixed all as specified and directed.

Supply and fix stop Valves of size 50 mm (2”) dia pipe cast copper alloy screwd down high pressure with crutch or butterfly handle screwd both hands for iron pipe or for unions and fixed all as specified and directed,

Valve chamber 600X600X600 mm size internally built with brick work in CM 1:6 plastering complete with CM 1:4 including necessary earth work, PCC 1:4:8, 100 mm thick as in foundation concrete including provision of cast iron hinged cover with using 2mm thick steel with "FH" empossed and painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth and getting out in soft/llose soil including making the bottom of trenches levelled for proper laying of pipe line, foundation etc or for shafts, cesspits, manholes, pier hole detecting defects/leakage in water pipe line etc not exceeding 10 sqm on plan and getting out in soft/loose soil as specified and as directed.

Taking out under ground 1.1 KV (E) Grade LT cable from pole/trenches/walls / ducts etc., for carrying out repairs, removing to store for safe custody for re use or for issue under schedule of credit complete all as directed by Engineer-in-Charge at site. size 240 Sqmm to 300 Sqmm x 3.5 Core

Supply and lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty)1100 Volts grade with stranded aluminium conductor of size of size 120 Sqmm 3.5 Core

Excavation in trenches n. exc. 1.5 M in width and 1.5 M in deep for laying of pipes and getting out in Soft / loose Soil

M&L for providing dry river sand / crush stone dust for cushioning to UG cable including punning down of sand in layers all as specified. Note :- Cushioning will be measured and paid after punning down.

Supply and laying factory cast, unreinforced precast concrete cable cover factory made embossed the mark “LT CABLE” class LV type1 flat size 250x150x40 mm laid in trenches as specified and as directed.

Supply and fix 4 Pole MCCB 400 Amp ,50Hz ,415 V with rupturing capacity 36 K from existing panel board as directed by Engineer-in-Charge at site.

M & L for Chemical earthing with copper earth plate 90x60cmx5mm & copper earth strip 32x6mm all as directed by EIC at site.

M&L for sub main wiring drawing through PVC casing and capping with two single core 4 sq mm and one run of 4 sq mm as earth wire of stranded copper conductor PVC insulated and unsheathed cable of 1100 volts grade all as directed. Note:- Three run of 4 sqmm wire and One run of PVC casing caping will be measured as one running meter.

M&L for point wiring in PVC casing caping with 1.5 Sqmm size multi stranded FRLS copper conductor cable 1.5 Sqm including clamps, screws guttier/plug etc PVC unsheathed cable into and including wooden board with bakelite sheet and PVC insulated FRLS cable of size 1.5 Sqmm as earth continuity conductor. (a) One 3 pin 5 Amp switch socket outlet on independent board

M&L for point wiring in PVC casing caping with 2.5 Sqmm size multi stranded FRLS copper conductor cable including clamps, screws guttier/plug etc PVC unsheathed cable into and including wooden board with bakelite sheet and PVC insulated fire retardant cable of size 2.5 Sqmm as earth continuity conductor.

S&F in repair Switch socket combination 2 in 1, 3/5 pin, 5 Amp flush type universal complete all as specified and as directed. Make : Anchor / Bajaj / Cona

S&F in repair Switch socket combination 2 in 1, 3/5 pin, 5 and 15 Amp flush type universal complete all as specified and as directed. Make : Anchor / Bajaj / Cona

S&F MCB DB TPN 4 ways double door with 440 Volt, 200 amps rated bus bar with all accessories flush in the wall including matching the existing surface all as specified and directed

S&F MCB DB SPN 4 ways double door with 240 Volt, 200 amps rated bus bar with all accessories flush in the wall including matching the existing surface all as specified and directed

S&F MCB TPN 40-63 amps, 440 Volts, Complete all as specified and directed.

M&L Earthing complete including taking down of old one with galvanised steel earth plate electrode of size 60cms x 60cms x 6.0 mm thick as per IS 3043 of 1987 buried directly in to the ground (earthpit not less than 2.25 m deep below the ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to the galvanised earth lead by means of bolts , nuts check nuts and washers of galnanised iron or steel using GI strip 25 x 4 mm as earthing lead as shown in electric plate No-3 of SSR- Part-1 connected to earth strip all as specifed or indicated including testing on completion and necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC 1 :3:6 type C-1 using 20 mm graded stone aggregate, pit, funnel, 15 mm diia meduim grade watering pipe, 40 mm dia GI light grade earth lead protection pipe, CI frame and cover , wire copper lugs etc mesh, charcoal and common salt in alternate layer complete all as specified and directed by Engineer In Charge.

M&L Flat Three Core PVC Insulated & PVC Sheathed Industrial copper Cable 10 sq mm complete fixing with clamps and screws as per required all as directd by EIC at site.

Cutting Existing 80/100mm bore CI water mains and inserting ferrules of size 25mm dia for taking branch connection including fittings all as specified and directed.

Supply and fix Straight plain brass ferrules 25mm dia or connecting screws) screwed both ends and fixed all as specified and directed.

Supply and fix stop Valves of size 25 mm (1”) dia pipe cast copper alloy screwd down high pressure with crutch or butterfly handle screwd both hands for iron pipe or for unions and fixed all as specified and directed,

Supply and lay tube light grade 25mm dia galvanized “Medium class with all fittings and fixed complete to walls and ceilings or laid in floors,” all as specified and directed.

Supply and lay tube light grade 50mm dia galvanized “Medium class with all fittings and fixed complete to walls and ceilings or laid in floors,” all as specified and directed.

Supply and lay tube light grade 100mm dia galvanized “Medium class with all fittings and fixed complete to walls and ceilings or laid in floors,” all as specified and directed.

Supply and fix sluice valve class PN1.6 of size 100 mm (4”) dia fixed all as specified and directed,

Supply and fix strainer for suction of capacity 100mm all as specified and directed,

Supply and fix non return butterfly valve of size 100 mm (4”) dia fixed all as specified and directed,

Supply and fix monoblock pump set with electric driven motor single phase 230 volts,50 Hz of capacity 5 HP complete with control panel (Comprising suitable FRP box with door ,DOL starter MCB DP and MCP SP of required capacity Indication lamps and wiring from stater to motor ,PCC foundation ,foot valave all as specified and as directed.

S&F mild steel work as in post and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc) including necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165

SAI SAMARTH ENTERPRISES

RK AND SONS CREATION

seema enterprises

M/s S.D Construction Co