SPL REPAIRS TO BLDG NO. T-39 OF ARTY BDE CAMP, BATHROOM AT BLDG NO P-140 OF MED REGT, LED STREET LIGHT AT UMRAO ENCLAVE AND PROVN OF KITCHEN AND 2 X TOILET BLOCKS FOR STN CELL AT AURANGABAD UNDER GE(SOUTH) AHMEDNAGAR

Amount

Dismantling of stone slab & tiles of any description in floor, laid, bedded & pointed in any mortar, all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles all as specified and as directed.

Demolition of cement concrete (un reinforced) in ground floor and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling of single layer Mangalore pattern or similar tiles in roofing including ridge tiles all as specified and as directed.

Dismantling of AC sheet (corrugated, semicorrugated etc) in roof covering including ridges all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls etc., including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and as directed.

Taking down chowkats or frames, area n.exc 1.5 Sqm each (without taking off shutters from frames) all as specified and as directed.

Taking down chowkats or frame, area exc 1.5 Sqm but n.exc 4.0 Sqm each (without taking off shutters from the frames) all as specified and as directed.

Taking down roof trusses etc., above 4 m & upto 8 m clear span all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, embedded in concrete, brick work, masonary, etc including taking out embedded portion and making good disturbed ground all as specified and as directed.

Taking up or down 15mm bore existing steel tubing and connections complete all as specified and as directed

Taking up or down 20mm bore existing steel tubing and connections complete all as specified and as directed

Taking up or down existing asbestos cement pressure pipe any class, (including all fitting ) including disconnecting pipes and fittings complete all as specified and as directed

Surface excavation n. exc. 30cm deep and averaging 15cm deep and getting out in soft/loose soil all as specified and as directed

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose soil all as specified and as directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25 cm thick in soil all as specified and as directed

Removing excavatd soil to a distance n. exc 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and as directed

Excavating post holes or similar holes, each not exceeding 0.5 Cum, getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick, watering, and removing surplus soil to a distance not exceeding 50 m and making good surface all as specified and as directed.

M&L for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface all as specified and as directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering all as specified and as directed

M&L for PCC, 1:4:8, type D2 (40mm graded stone aggregates) as in foundation filling and mass concrete etc. complete all as specified and as directed.

M&L for PCC, 1:3:6, type C2 (using 40mm graded stone aggregates) as in foundation, filling and mass concrete etc. complete all as specified and as directed.

M&L for PCC, 1:2:4, type B1, using 20 mm graded stone aggregates as cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs and the like including formwork, weathering, slightly rounded or chamfered angles and throating, all as specified and as directed

M&L for brick work with fly ash bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as specified and as directed.

M&L for brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 all as specified and as directed.

M&L for damp proof course of 40 mm thick in cement concrete 1:2:4, type B-0, using 12.5mm graded stone aggregates, to horizontal or vertical surfaces including necessary formwork complete all as specified and as directed.

S&F 35 mm thick, second class hard wood, glazed and and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkats all as specified and as directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F solid PVC door frames of size 50 mm x 47 mm, made out of 5 mm thick plain colour PVC sheet reinforced with M.S. square tube, suppling & fixing in opening as per specification & drawing all as specified and as directed..

S&F factory made solid panel PVC door shutter, 30 mm thick (Style) consisiting of frame made out of MS tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain coloured PVC 'C' channel having a PVC sheet strip of 20 mm which stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing all as specified and as directed..

S&F factory made solid PVC moulded door shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing with 2mm thick moulded prelam PVC sheet on the front face & 2mm plain colour PVC sheet on back face all as specified and as directed

S&F 200 mm long aluminium anodised barrel barrel tower bolts of extruded section and fixed as specified and as directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed

S&F 100mm long butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and as directed.

S&F 100 mm long butt hinges, extruded alminium alloy with galavanised mild steel hinge pin, anodised and fixed , type C-21 all as specified and as directed.

S&F 125 mm size aluminium handles, cast type, anodised complete all as specified and as directed.

S&F in repairs, Harrison curtain rails, 20 mm dia, anodised aluminium alloy, chromium plated including brackets, stops, rollers etc., complete all as specified and as directed.

S&F galvanised mild steel wire clothes 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and as directed .

S&F mild steel flat iron 40 x 6 mm as in wind ties for roofing including securing bolts, all as specified and as directed.

M&L or framed work such as grills grating etc with end of bars shoulderd and/or riveted .welded or forged into spikes.framedguard bars iron doors.ladders framed balusters , walk ways. railings, frame work of water tanks and similar work conforming to Fe410 all as specified and as directed.

S&F mild steel bolts, exc 12mm dia and n exc 20mm dia, exc 300mm long MS screw bolt machine made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers , all as specified and as directed.

S&F rolled mild steel plates (plain or chequered) channels, square cut or notched, forming holes, with riveted, bolted or welded attachment, conforming to Fe 410 -W (Gde- E- 250) quality- A all as specified and as directed.

S&F rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410 -W (Gde- E- 250) quality- A all as specified and as directed.

S&F rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.Fe 410 -W (Gde- E- 250) quality- A all as specified and as directed.

S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161- 1979 grade St.-240, all as specified and as directed.

S & F rolled mild steel framed work as in chowkats or frame of door or gates of angle or other section with gusset plate , rail braces etc complete drilled for fixing of steel sheeting or other covering , doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fiting(exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed.

S&F mild steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, devotailed or welded all as specified and as directed..

S&F mild steel windows with side hung shutters including projecting type hinges with steel handles, and steel peg stay complete without glazing bars, dovetailed or welded all as specified and as directed..

S&F mils steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and as directed

M&L in repairs, for gypsum board 12 mm thick for insulation and accoustic purposes, 60 cm x 60 cm in size, fixed with staples on and including snap grid Gl frame work for seamless ceiling comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with and including Gl hangers made out of 6 mm dia GI wire (up to 1200 mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of GI flat 40 x 3 mm size 60 mm long and expension hold fasteners 12.5 mm dia. 40 mm long with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.including necessary fixing/ repair /replacement of existing electrical fittings at site complete all as specified and as directed.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of colour as approved by GE, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and as directed.

M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of colour as approved by GE, having tensile strength of 550 Mpa as in roof covering/ridges/valley gutters/cladding to wall, fixed with self tapping screws all as specified and as directed.

M&L for 20mm granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified and directed

M&L for 20mm thick granite (of any type) slab, machine cut, bedded and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone, laid over and including 20mm thick cement screed in cement mortar 1:6, grinding and polishing complete, all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations all as specified and as directed.

M&L for machine cut cudappah stone slab 20-25mm thick over and including 15mm thick cement screed base in CM 1:6 , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L for 75mm thick PCC 1:4:8, type D2, using 40mm graded stone aggregates as in sub base of flooring complete all as specified and as directed.

M&L for 100mm thick PCC 1:4:8, type D2, using 40mm graded stone aggregates as in sub base of flooring complete all as specified and as directed.

M&L for 40mm thick PCC 1:2:4, type B1, using 20mm graded stone aggregates, laid in panel, finished even & smooth with using extra cement as in flooring complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

S&F glass dividing strips, 3mm thick and 38mm wide, inserted in position, conform to design of flooring complete all as specified and as directed

M&L for machine cut kota stone flooring, 20-25 mm thick (size of kota stone slab 22"x22") laid over and including 20 mm thick bedding layer of cement mortar 1:6 jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing including removing dust complete all as specified and as directed.

All as per serial item No. 64 here-in-before but 18 to 20 mm thick kota stone on vertical surfaces such as in skiting /dado of size as required at site over and including10 mm thick backing coat of cement mortar (1:4) complete all as specified and as directed.

M & L for glazed ceramic coloured tiles in vertical surface, size 300 mm x 200 mm x 7 mm thick, laid over and including 10 mm thick in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white cement or colour cement to match the colour of tiles all as specified and as directed.

M & L for glazed ceramic coloured tiles in vertical surface, size 350mm x 250mm x 7mm / 450mm x 350mm x 7mm thick, laid over and including 10 mm thick in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white cement or colour cement to match the colour of tiles all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exc 0.06 sqm but not exc 0.11 sqm, shade as approved by GE, as in floors etc., laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M&L for machine pressed precast glazy finished concrete interlocking blocks any shape and any size confirming to IS 15658-2006 of 80mm thickness, M -40 grade with grey cement and pigment, laid over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; etc complete all as specified and as directed.

M&L for 10 mm thick rendering in cement mortar 1:6 on fair faces of brick masonry surfaces or concrete surface, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 10 mm thick rendering in cement mortar 1:6 over dubbing out average 10 mm thick on irregular faces of wall in cement mortar 1 : 6 on stone masonry surfaces or surfaces other than fair faces of brick-work, finished finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4, finished even and smooth without using extra cement, all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on stone masonry surfaces or surfaces other than fair faces of brick-work, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10mm thick on fair faces of concrete surfaces in cement mortar 1:3, as in ceiling, soffit of slab, etc. finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white complete all as specified and as directed.

M & L for preparation of plastered or unplastered surfaces of walls and applying one coat of primer over a coat of 1 mm thick (average) white cement putty, sanding the surfaces till smooth finish is obtained and finally applying two coats of oil emulsion distemper etc complete all specified and as directed

M&L for complete removal of existing treatment of old plastered surfaces of walls and applying two coats of oil bound distemper over one coat of chalk whitening all as specified and as directed.

M&L for complete removal of existing treatment of old plastered surfaces and applying two coats of oil bound distemper over one coat of chalk whitening on ceiling complete all as specified and as directed.

M&L for preparation of new plastered surfaces or previously untreated surface of wall and applying two coats of cement base paint over one coat of alkali resistant primer all as specified and as directed.

M&L for preparation of old plastered or unplastered surfaces of walls and applying two coat of cement base paint complete all as specfied and as directed

S&F 3mm thick plain sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 Sqm in each pane complete all as specified and as directed.

S&F 3mm thick frosted (one side) sheet glass ordinary quality and glazing with oil putty, pinted pin in square n exc 0.5m sqm in each pane all as specified and as directed.

M&L for preparation of new wood or wood based surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over one coat of pink primer complete all as specified and as directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paints over one coat of red oxide zinc chrome primer complete all as specified and as directed.

S&F 15mm bore GI water tubing medium grade galvanised with all fittings and fixed complete to walls and ceilling or laid in floor all as specified and as directed

S&F 20mm bore GI water tubing medium grade galvanised with all fittings and fixed complete to walls and ceilling or laid in floor all as specified and as directed

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 500 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia Ball valves ,high pressure with polythene float and flynut complete screwed for iron pipe and connecting all as specified and as directed.

S&F in repairs, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 500 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia Ball valves ,high pressure with polythene float and flynut complete screwed for iron pipe and connecting all as specified and as directed.

S&F in repairs, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 1000 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia Ball valves ,high pressure with polythene float and flynut complete screwed for iron pipe and connecting all as specified and as directed.

S&F bib taps, 15mm dia, chromium plated with crutch or butter-fly handle, screwed down for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F in repair, bib taps, 15mm dia, chromium plated with crutch or butter-fly handle, screwed down for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F angle cock, 15mm bore, chromium plated, fancy type, screwed down high pressure with crutch or butterfly handles, screwed both ends for iron pipe or for union and fixed complete all as specified and as directed.

S&F in repairs, angle cock, 15mm bore, chromium plated, fancy type, screwed down high pressure with crutch or butterfly handles, screwed both ends for iron pipe or for union and fixed complete all as specified and as directed.

S&F 15mm bore dia, stop valve cost copper alloy, fancy type , chromium plated with long shank and cup concealed, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union, complete all as specified and directed.

S&F in repairs, 15mm bore dia, stop valve cost copper alloy, fancy type , chromium plated with long shank and cup concealed, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union, complete all as specified and directed.

S&F 20 mm dia, gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe all as specified and as directed.

S&F in repairs, 20 mm dia, gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe all as specified and as directed.

S&F in repairs, swivel shower rose of PTMT any colour for fixing with 15mm pipe (Minimum weight 40 gms) all as specified and as directed.

S&F PVC connection, 15mm bore length, not less than 300 mm long with both ends PTMT nuts complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes of single socketed in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F 110 mm bore PVC (SWR) pipes of single socketed in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F 75 mm dia PVC (SWR) bends of any radius complete all as specified and as directed

S&F 75 mm dia PVC (SWR) floor trap, plain, with greting including jointing with solvent cement all as specified and as directed.

S&F in repairs, 75 mm dia PVC (SWR) floor trap, plain, with greting including jointing with solvent cement all as specified and as directed.

M&L for PCC 1:4:8, type D-2, using 40 mm graded stone aggregates as in concrete bed for 110 mm bore dia drain pipes, any type, including packing under and haunching against the sides of the pipes after they are laid & tested complete all as specified and as directed.

S&F vitreous China, white, squatting pan, "Orissa" pattern of size 580 X 440 mm width with integral foot rest, set in cement concrete including flush pipe and connecting to trap / flushing cistren and making good to floor complete all as specified and as directed.

S&F in repairs, vitreous China, white, squatting pan, "Orissa" pattern of size 580 X 440 mm width with integral foot rest, set in cement concrete including flush pipe and connecting to trap / flushing cistren and making good to floor complete all as specified and as directed.

S&F in repairs, vitreous china wash down water closet ( pedestal pattern) including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for pedestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed.

S&F in repairs, 10 litres capacity PVC valveless syphonic action type, flushing cistern, low level, white or coloured, with inlet, ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density PVC 32 mm dia for low level cistern complete all as specified and as directed.

S&F vitreous china wash hand basin, white flat back size 550 mm x 400 mm including brackets including pillar tap, 15 mm bore chromium plated, fancy type, cast copper alloy with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks, 32 mm dia waste coupling of PTMT (half or full thread, minimum weight 40gms) suitable for wash hand basins, with long screwed shanks and fly nuts complete all as specified and as directed.

S&F in repairs vitreous china wash hand basin, white flat back size 550 mm x 400 mm including brackets including pillar tap, 15 mm bore chromium plated, fancy type, cast copper alloy with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks, 32 mm dia waste coupling of PTMT (half or full thread, minimum weight 40gms) suitable for wash hand basins, with long screwed shanks and fly nuts complete all as specified and as directed.

S&F kitchen sink with drainage board made out of 1mm thick stainless steel with plugs, washers & wastes including CI cantilever bracket, 32mm dia waste coupling of PTMT(minimum weight 40gms, half or full thread) & connection union to pipe over all size 915mmx460mm & bowl size 410 x330x160mm complete all as specified and as directed.

S&F in repairs,32 mm bore of pipe low density polythene pipe (LDPE) of pressure rating 6Kgf/sqcm fixed to wall or laid in floor etc including fittings complete all as specified and as directed.

S&F PVC flexible waste pipe of standard length 32mm dia, with PVC cap suitable WHB waste coupling, all as specified and as directed.

S&F in repairs, 100mm dia grating doom with waste hole of PTMT (Minimum weight 25 gms) all as specified and as directed.

S&F vitreous China bowl urinal, flat back, size 465mm x 355mm x 265mm, white (minimum), with grating and union for discharge pipe, urinal spreader PTMT (excluding flushing cistern, flush pipe and waste pipe) all as specified and as directed.

S&F in repairs, vitreous China bowl urinal, flat back, size 465mm x 355mm x 265mm, white (minimum), with grating and union for discharge pipe, urinal spreader PTMT (excluding flushing cistern, flush pipe and waste pipe) all as specified and as directed.

S&F 600mm x 450mm bevelled edges mirror consisting of 5.5mm thick commercial plywood and fixed to plug with chromium plated brass screwed and cup washer all as specified and as directed.

S&F in repair, 600mm x 450mm bevelled edges mirror consisting of 5.5mm thick commercial plywood and fixed to plug with chromium plated brass screwed and cup washer all as specified and as directed.

Taking down carefully unserviceable copper/aluminium point wiring (light, fan/bell,plug and power socket etc.) complete, (fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc.) and making good of disturbed surfaces all as specified and as directed.

Taking down the existing unserviceable main switches/ MCB/DB's of any type including boards from its position and making the good of disturbed surface complete all as specified and as directed.

Taking down the existing unserviceable submain wiring of any type including boards from its position and making the good of disturbed surface complete all as specified and as directed.

M&L for point wiring with two run of 1.5 sq mm PVC insulated and unsheathed, multi-stranded copper conductor, FRLS cable, 1100 volt grade, single core, laid in and including casing and capping/PVC concealed/surface conduit size not less than 20 mm dia complete with all accessories /fittings round block etc, first class switch board suitable for modular white cover plate with frame and metal flush box of suitable size for mounting modular switch/ sockets/regulators etc and one run continuous earth wire 1.5 sqmm, PVC insulated and unsheathed copper conductor cable and connected to common earth dolly for one light/fan /bell point controlled by one switch all as specified and as directed.

All as per serial item No 123 here-in-before but for one 3/5 pin, socket outlet point controlled by one way switch of 5/6 Amp on same board

All as per serial item No 123 here-in-before but with 4 sqmm copper cable for multi-purpose 5/15 Amps socket outlet on independent board

All as per serial item No 123 here-in-before but with 2.5 sqmm copper cable for multi purpose 5/6 Amps socket outlet on independent board.

S&F switch piano, flush type single pole, one way 5 Amp complete all as specified and as directed.

S&F switch piano, flush type single pole, one way 15 Amp, ISI marked complete all as specified and as directed.

S&F modular switch, single pole, one way, 5/6 Amps, 1 module, 240 volts, ISI marked complete all as specified and as directed.

S&F modular switch, single pole, one way, 15/16 Amps, 1 module, 240 volts ISI marked complete all as specified and as directed.

S&F modular socket outlet (ISI marked), 2/3 pin, combined, 5/6 amps, 2 module, flush type complete all as specified and as directed.

S&F modular socket outlet (ISI marked), 2/3 pin, combined and 15/16 amps, 2 module, flush type, complete all as specified and as directed.

S&F socket outlet, 2 in 1, 3 pin, 5 and 15 amp flush type all as specified and as directed.

S&F socket outlet, 2 in 1, 3 pin, 5/6 amp flush type all as specified and as directed.

S&F ceiling rose, surface type, bakalite, 3 terminals complete all as specified and as directed.

S&F lamp holder, angular type, insulated body, wall mounted with back plate complete all as specified and as directed

S&F stepped type electronic modular fan regulator, 120 W, 2 module, complete all as specifed and as directed

Taking down exhaust fan /ceiling fan, any size,sealing cable end, complete all as specified and directed by Engr-in-Charge.

S&F ceiling fan, 1400 mm sweep with all accessories like hook, clamp, blades, down rod, canopy and making connection complete all as specified and as directed.

S&F exhaust fan, AC single phase, 230/ 240 V, size 300 mm sweep, metallic body, copper wound with self opening and closing louvers, fixing by means of rugged bolts, nuts and washers etc and foundation brackets, making connection from ceiling rose to fan with and including 1.5 sqmm copper conductor cable including making hole in existing brick/stone masonry and testing at site complete all as specifed and as directed .

S&F single pole and neutral enclosure with a 3 pin plug and socket complete with one single pole MCB 25 Amp, 240 Volts, for geyser complete all as specifed and as directed .

S&F LED lamp 9 watts complete all as specifed and as directed . Make : Cromption Cat No LX9 or equivalent in Philips / GE / Halonix / Century LED / Havells

S&F LED light fitting 10 watt 230 volt including 10 watt LED tube, extruded aluminium for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete all as specified and as directed. Make:- Jaquar Model-LGLZ01X010XC/ LGLZ01X010XN/LGLZ01X010XW or Havells Model-LUMILINEPLUSBS10WLED865SPCSS or equivalent model of make Philips / GE/ Crompton/ Halonix/ Century LED

S&F LED box type fitting pre-wired including LED tube 1 x 20 W connecting up with PVC insulated and sheathed 1100 volt grade flexible copper cable complete all as specified and as directed. Make:- Jaquar Model-LGLZ01X020XC/ LGLZ01X020XN/LGLZ01X020XW or Havells Model-LUMILINEPLUSBS20WLED865SPCSS or equivalent model of make Philips / GE/ Crompton/ Halonix/ Century LED

S&F 24 watt LED, recessed mounted luminaire, 240 V, Mains Current = 0.115 A, PF= 0.95, THD(%) ≤20, CCT = 6500 K, CRI≥80, System lumens 3030 lm, suitable for Armstrong/Grid ceiling complete all as specified and directed. Make : Halonix Cat No HLFPR22-05-24-C-W-R-HL2 / Havells Cat No : PLANO2X2PLR24WLED865S or equivalent model in make Philips / GE/ Crompton/ Century LED

S&F LED street light of capacity 30 Watt,made up of pressure die cast aluminium housing with highly efficient LEDs as lighting source and PC cover with integrated lens with IP66 protection and impact resistance of IK07 including electronic driver, Operating temperature: -10 °C to + 50 °C, Operating voltage range: 140 V - 270 V, Average life L70B50: 50000 hours, System Lumen Efficacy ≥100 Lm/W, High efficiency long life LED module with SMD LED package mounted on MCPCB. Lumen efficacy of LED >145 lm/W, PF ≥0.95, THD%<10, CCT=5700 K, CRI≥70, Powered by Built-in, isolated electronic LED driver (SMPS based constant current supply) with lower THD, Output Open / Short Circuit protection, Over Voltage protection, Phase to Phase protection, Surge Voltage protection & other safety test as per IS 15885 Part-2/Sec 13 all as specified and as directed. Make : Havells Vat No - VILUMINASL30WLED757PASYBOPC / Halonix Cat No - HLSLD-14-30-CWDL-P or equivalent model of make Philips / GE/ Crompton/ Century LED

S&F MCBs, SP 6 to 32 Amps, 10 KA, 'C' curve, IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed. Make :- Legrand Cat No 4085 87 to 4085 95 or equivalent model of make Hager/ Siemens/ ABB/ Schneider/GE/C&S Electricals Ltd.

S&F MCBs, SPN 6 to 32 Amps, 10 KA, 'C' curve,IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed. Make :- Legrand Cat No 4085 87 to 4085 95 or equivalent model of make Hager/ Siemens/ ABB/ Schneider/GE/C&S Electricals Ltd.

S & F in repairs, MCBs, DP 6 to 32 Amps, 240v 10 KA, 'C' curve complete all as specified and as directed. Make :- Legrand Cat No 4086 28 to 4086 36 or equivalent model of make Hager/Siemens/ABB/Schneider/GE/C&S Electricals Ltd.

S&F MCB TPN of capacity 40A to 63A,10 KA, type 'C' curve, 240 Volts, complete all as specified and as directed. Make :- Legrand Cat No 4086 81 to 4086 83 or equivalent model of make Hager/ Siemens/ ABB/ Schneider/GE/C&S Electricals

M&L for PVC insulated, heavy duty electric cable, flat or circular, with aluminium conductor, one twin core, cross sectional area 10 sq mm, 1100 volts grade, served with an inner sheathing of PVC tape and over all PVC sheathed in service connection suspended by insulating hangers not more than 1 metre apart including 4mm dia GI suspension wire all as specified and as directed

M&L in repairs, XLPE insulated, armoured heavy duty electric cable with alluminium conductor, 3.5 core,1100 volts grade, cross sectional area 25 sq mm including electric connections on both ends with suitable lugs,binding wire all as required at site all as specified and as directed

S&F sheet metal enclosure for DB SPN 4 way with 200 Amp rated bus bar 240 Volts , double door suitable for housing MCBs and isolators complete all as specified and as directed

S&F sheet metal enclosure for DB SPN 8 way with 200 Amp rated bus bar 240 Volts , double door suitable for housing MCBs and isolators complete all as specified and as directed

S&F sheet metal enclosure for DB TPN 4 way with 200 Amp rated bus bar 240 Volts , double door suitable for housing MCBs and isolators of metering boards fabricated out of 2 mm thick CRCA suitable for mounting 4 No of 3 phase/single phase energy meters with fixing and locking arrengement complete all as specified and as directed.

M & L for sub main wiring with 2 runs of 6 sqmm, single core, PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20 mm dia non metallic PVC grey conduit conforming to IS-9537 / suitable size casing caping (ISI marked) with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 6 sqmm single core PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion all as specified and as directed. Note : Three runs of 6 Sqmm cable and one run of PVC conduit will be measured as one Rm unit.

S&F LED street light of capacity 60 Watt made up of pressure die cast aluminium housing with high power LED as light source and lens embedded PC cover including electronic driver should have system luminaries efficacy ≥110 lumens/watt, CRI>70 ,PF > 0.95,CCTCCT≥5500, IP66,impact resistance IK 07 ,inbuilt protection against lightning , over voltage , short circuit and surge/spike protection not less than 5kV complete all as specified and directed. Make : Crompton, model :LSTP-60-CDL-M / Century Led,model : SPOR060C0805 /Halonix, model : HLSLD-10-60-WWL-I /Havells, Model ENDURAOMNIPLUSSL60WLED757SASYTOPC

S&F street light bracket made of GI pipe 40 mm bore light grade(bend to shape) , 3 metre long and fixed with mild steel flat iron clamp(clamp shall be 50 X 6mm ), nuts, bolts and washers on pole complete all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode 60x60x6.3 mm thick, buried directly in ground (earth pit not less then 2.25 metres deep below ground level) with top edge pf the plate not less then 1.5 metres below normel ground level, conneted to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, cheek nuts and washers of galvanisedor iron protected by 15 mm bore GI pipe (medium grade) and connected to main switch board as directed including concrete pit in PCC (1:3:6) type C1 precast RCC (1:2:4) type B1 cover slab 40cm x 40cm x 5cm, reinforced with 8 mm dia deformed bar @ 5 cm c/c with one handle for lifitting made out of 8 mm dia MS bar, funnle, wire mesh, 20 mm bore GI pipe (medium grade) for watering including charcoal, coke and salt in alternative layers necessary excavation and earth work in any type of soil and testing complete all as shown on electrical plate No-3 of SSR part-I, 2009.

M/s S.R lahoti