Renovation of samja Ghar of Nawa Deepak Ghar Samity at Deepak Tole, Reshep GP

Earthwork in excavation in foundation trenches Or drains,in all sorts of soil (including mixed soil but excluding laterite or sandy soil ) including removing spreading or stacking the spoils within a lead of 75m as directed.The iteincluding necessary trimming the sides of trenches,leveling dressing and ramming the bottom bailing out water etc as required complete.

Labour for laying 150 mm to 200 mm boulder soling including rough dressing hand packing and ramming down small pieces in the interstics including rolling and preparing the bed to proper level and filling up all joints with sandy clay or earth.

Cost of Boulder

Cement concrete with 40 mm down graded Singles excluding shuttering in ground floor ( 1 : 3 : 6 ).

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.

Reinforcement for reinforced concrete work in all sorts of structure including distribution bars ,stirrups,binders etc. including supply of rods initial straightening and removal of loose rust,cutting to requisite length hooking and binding to correct shape placing in proper position and binding with 16 gauge blackanelled wire. SAIL/TATA...etc

Hire and labour charges for shuttering with centering and necessary staging upto 4m. using approved stouts props and thick hard wood planks of approved thickness with required bracing for concrete slabs,beams,lintels etc. including fitting fixing and striking out after completion of work.

125mm thick brickwork with 1st class bricks in cement mortar (1:4) in ground floor.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface].

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals).

Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor.

Supplying fitting & fixing M.S Clamps for door & window frames made of flat bent bar, end bifurcated with necessary screws etc. in cement concrete (1:2:4) including cutting of brick work/ concrete as per direction. (Cost of concrete will be paid separately).

Anodised aluminium Aldrop/ Sliding bolts of approved quality manufactured from extruded section conforming to I.S specification ( I.S. 2681/66) fitted & fixed. (250 mm dia 19mm bolt)

Iron Butt hinges of approved quality fitted & fixed with steel screws, with ISI marks.

Anodised Aluminium ‘D’ type handle from of approved quality manufactured from extruded section conforming to I.S.230/75 with hexagonal or found rod supplied, fitted& fixed complete. (75 mm grip x 10mm dia rod)

Anodised aluminium skeleton bolt of approved quality manufactured from extruded section conforming to I.S: specification (I.S: 204/74) fitted and fixed with cadmiim plated screws:

Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Colour washing with "ELLA" with a coat of white wash priming including cleaning and smoothening surface thoroughly :

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary

Galvanized corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugaion minimum side lap. ( payment to be made on area of finished work). (GCI sheet to be supplied by contractor).

Galvanised iron sheet ridging fitted with necessary bolt, screws, washers etc complete. (225 mm end lapping).

(A) Wood work in posts, post plates, rafters, battens, truss members, purlins etc. fitted and fixed complete (excluding the cost of bolts, paints, but including the cost of nails, screws etc.) (ii) Sal : Local.

Add extra for unseen items

Add GST @ 18%

Add CESS @ 1%

Please Enable Macros to View BoQ information