SPL REPAIR OF 70 X SECURITY LIGHT AT FAZALPUR 9 INF DIV ORD UNIT AND PROVN OF ADDN SECURITY LIGHT AND LED FLOOD LIGHT AT KULWANT SINGH STADIUM UNDER GE(U) MEERUT CANTT.

Amount

Taking out unserviceable Street lights any type and size and Supply and fixing LED street light fitting 70/72 watts , 140 V - 270 V , 50Hz AC outdoor type with high pressure die cast alluminium housing with top opening service and heat resistant complete with driver, lamp bracket , with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection , Light sensing with auto on off as per ambient light conditions, High efficiency long life LED package modules on MCPCB with LED lumen efficacy of >110 lumen per watt, Electronic Driver Powered by Built-in, isolated electronic LED driver (SMPS based constant current supply) with lower THD, Output Open / Short Circuit protection, Phase to Phase protection, Over Voltage protection, 10 kV surge protection, Surge Voltage protection & other safety tests as per IS 15885 Part-2/Sec13 completed to driver with superier finish with top maintanable driver compartment complete all as Specified and directed.

Taking out existing unsv junction box any type and size and S&F pole mounting type junction box factory made of minimum size 290 x200x100mm of FRP sheet duly powder coated with front openable hinged door , locking arrangements, with 4 Nos aluminium bus bars 40 Amps rating mounted on SMC /porcelain insulator, cable glands and lugs consisting DIN type rails for fixing MCB SP 6/10 Amps, 10 kA suitable for domestic loading , -01 no. including mild steel flat iron clamp and and supporting flat Iron made out of 40x4mm FI, nuts, bolts and washers duly painted with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F in replacement for one runs of three core 1.5 Sqmm x 3 core (nominal area) PVC insulated and PVC sheathed multi stranded unarmed copper conductor cable LT 1100 volt grade Confirming to IS : 7098 drawn through existing tubular pole for connecting to street light and pole JBs complete as all specified and as directed.

Taking down old pipe & Material and labour for light grade GI pipe 40 mm bore of approx. 1.5 mtr length and fixed to pole with FI 40mm x 6mm clamps, 01 nos and suitable size necessary nuts & bolts including throwing Lt cable complete with painting two coat of aluminium paint and one coat of red oxide complete as all specified and directed.

Taking out Existing Street / security lights Bracket any type and size and Supply and fixing of mounting bracket made of 40 mm bore (or higher size to suit the opening of fitting) light grade GI pipe of approx 1.5 mtr length bent to shape and fixed to pole with FI 40mm x 6mm clamps, 2 nos and suitable size necessary nuts & bolts ,including Bracket complete set painting of two coat red oxide and aluminium painted fittings for Street lights with swaged tubular/ PCC pole connected all as specified and as directed Engr in charge.

Dismantling of Old PCC and M&L for PCC (1:2:4) type B-1 using 20 mm graded stone aggregate for coping of poles including necessary form work, fair finishing to exposed surfaces using extra cement

Taking out old unsv existing UG cable any size/ type incl dismantling any cable connections from junction boxes throughout the span and removing cable cable connections from supply source complete all as specified and directed.

Supply, laying, jointing, testing and commissioning LT underground cables 16 sqmm x 4core, 1100 volts grade, XLPE insulated and PVC sheathed, heavy duty armoured, with multistranded aluminium conductors, IS-7098 (marked, laid in trenches / ducts / fixed on poles / laid under roads / paths / drain / culverts or encased in GI pipe complete all as specified and directed. (Note;- Rate quoted includes terminal Lugs / road cutting/ floor cutting/ Inter locking floor and making good damaged portion matching with existing surface with all existing finishes.) complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in Soft/Loose soil including trimming sides and bottom of trenches complete all as specified in the following type of soils:

Returning, filling-in, including spreading, watering and well ramming in layers not exceeding 25 cm thick each, in soft /loose soil complete all as specified in the following type of soils

Removing excavated surplus soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified.

M & L for river washed and screened, dry sand for filling in trenches below and around underground cables for cushioning of cables complete all as specified. (Note:- Punned thickness shall be measured for payment)

M & L for Bricks for protection cover to under ground cable (with standard size fly ash bricks) with width equal to length of brick laid dry and flat abutting each other with gaps between adjacent brick not exceeding 10mm as directed.

Taking down old GI Pipes and Supply and laying galvanised steel tubing, light grade, 50 mm bore, IS-1239 marked with all fittings (IS marked) and laid in trenches / under roads / in drains / fixed to poles/walls ( with required size flat iron clamp bolts, nuts and washers ) pipes of the following sizes :-

M&L for auguring of hole suitable for passing 40mm to 100mm bore pipe in true horizontal position under road, PCC paths etc., by means of mechanical ring/ auger after doing ultrasound to prevent any damage to existing cables pipe line specified and directed coming in the route not exceeding 1.5 m in depth below existing surface level of road and not excd 30M in length complete all as specified. Note: Pipe shall be measured and paid separately under appropriate items and any dahage to existing cables of anytype shall be made good by the Bidder without any extra cost to department.

M&L for preparation of old painted surfaces steel tubular swaged poles / Rails/Girder poles of LT over head line ( Except embedded portion) , 9 M long including all MS work mounted on pole , earth protection & water pipe ( if exists) including bracket(s), single or double of size 1.5m x 40/50 mm pipe ) and providing one coat of aluminium paint and providing 05 Nos bands/ straps with Two coats of retro reflective paint ( Black, Green and 30 cm wide each) from top of plinth block and numbering of poles with white reflective paint (50mm wide and 100mm hight letters) including encircling the letters or figures complete all as specified and directed.

Taking down old u/s lights and Supply, installing, commissioning and testing LED 100W solar AIO LED Street Light on existing pole with luminaire efficacy of 150 lm/W with minimum lumen output of 110 lm/W along with solar panel should be of 150W with Monocrystalline cells with 78Ah Lithium Iron PO4 Battery pack. Manufacturers Logo/name must be engraved/Embossed on luminaire housing. Manufacturer must have in-house NABL accredited laboratory with scope of testing & callibration of Electrical, Mechanical & Photometry Parameters as per IS 10322:2012, IS16104,IS16106, IES LM 79. Solar light fittings should be reliable to fit on any size of GI Pipe bracket complete all as specified and directed. The Contractor shall submit below mentioned documents to Engineer-in-charge before bringing materials for installation (1) LM 79 Report from NABL accredited lab of light supplied. (2) Technical Data sheet of Solar Street Light (3) Type Test Report of Solar Street Light (4) BIS Certificate of Battery (5) LM80 Report of LED Chip used in fixture (6) Data sheet of LED Chip used in fixture

Supplying, transporting to site, erecting, and fixing in position, steel tubular swaged and welded poles of Overall height 9 metres, type 410 SP-31, IS-2713 marked, with cast iron base plate (fillet welded to poles), pole cap / finial taper plug, bolts, nuts, washers etc, including painting on the outside with two coats of aluminium paint over a coat of red oxide primer on exposed surfaces and black bituminous paint on steel surface embeded in concrete and painting 05 nos band /strips with fluorescent , Black/ Red/ White/ Green and Black synthetic enamel paint ( 30 cm wide each) at a distance of 30 cm from plinth block and numbering of poles, complete all as specified and directed.(Note:- Poles shall be swaged and welded at manufacturer’s factory and not at site. The inner surface shall be factory painted)

Supplying, transporting to site, erecting, and fixing in position, steel tubular swaged and welded poles of Overall height 11 metres, type 410 SP-55, IS-2713 marked, with cast iron base plate (fillet welded to poles), pole cap / finial taper plug, bolts, nuts, washers etc, including painting on the outside with two coats of aluminium paint over a coat of red oxide primer on exposed surfaces and black bituminous paint on steel surface embeded in concrete and painting 05 nos band /strips with fluorescent , Black/ Red/ White/ Green and Black synthetic enamel paint ( 30 cm wide each) at a distance of 30 cm from plinth block and numbering of poles, complete all as specified and directed by Engr-in-Charge.(Note:- Poles shall be swaged and welded at manufacturer’s factory and not at site. The inner surface shall be factory painted)

Supply and fixing LED street light fitting 70 watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, including thermal mamangement in multiple optics and equipped with IP65 protection complete all as specified and directed.

Supply and fix LED flood light fitting 210 Watts 230V AC outdoor type with thermal management in multiple optics and equipped with IP-66 protection, with impact and corrosion resistant complete with driver and lamp complete all as directed.

S&F pole mounting type junction box factory made of size 300x200x100 mm of FRP sheet duly powder coated with front openable hinged door, locking arrangements with 04 nos. Al bus bar 40 Amps rating mounted on porcelain insulator, cable glands and lugs consisting DIN type rails for fixing MCB SPN 6/10 Amps 10 KA suitable for domestic loading-01nos. including mild steel flat iron clamp made out of 40x4mm FI, nuts, bolts and washers duly painted with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F pole mounting type junction box factory made of size 300x200x100 mm of FRP sheet duly powder coated with front openable hinged door, locking arrangements with 04 nos. Al bus bar 40 Amps rating mounted on porcelain insulator, cable glands and lugs consisting DIN type rails for fixing MCB SPN 25/32 Amps 10 KA suitable for domestic loading-04nos. including mild steel flat iron clamp made out of 40x4mm FI, nuts, bolts and washers duly painted with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F for one run of 3 core 2.5 sqmm (nominal area) PVC insulated and PVC sheathed multi stranded copper conductor cable LT 1100V grade conforming to IS: 70987 for connecting to street light and pole JBs complete all as specified and directed.

M&L for MS cross arms in form of square brackets suitable for accomodating 4 LED flood lights of 210 W, bracing, supports, clamps and back plates fabricated from structural steel section including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolt, in any shape or size as indiacted and directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified and directed.

S&F of mounting bracket made of 40mm bore (or higher to suit the opening of fitting) light grade GI pipe of approx 1.5 mtr length bent to shape and fixed to pole (30cm bend approx 120 degree angle ) with FI 40mmx6mm clamps-02nos. And suitable size nuts,bolts, including bracket complete set and painting with two coats of aluminium paint over one coat of red oxide primer complete all as specified and directed.

S&F cable throwing pipe of 40mm bore (or higher to suit the opening of fitting) made of light grade GI pipe of approx 1.5 mtr length and fixed to pole with FI 40mmx6mm clamps-01nos. And suitable size nuts,bolts, including bracket completye set painting with two coats of aluminium paint over one coat of red oxide primer complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and depth exc. 1.50 m but not exc. 3.00 m and getting out in Soft/Loose soil including trimming sides and bottom of trenches complete all as specified and directed.

M&L for cement concrete type C2 1:3:6 using 40mm graded stone aggregate in foundations, filling and mass concrete (around the poles in pit) complete all as specified and directed..

M&L for cement concrete type D2 1:4:8 using 40mm graded stone aggregate in foundations (below pole) complete all as specified and directed.

Jain Traders (BID ID -3503460)

KUKREJA BROTHERS (BID ID -3499059)

PK ENTERPRISES (BID ID -3506023)

M/S JPS Electrical Engineer & Contractor (BID ID -3497027)

NITHYA INFRATECH (BID ID -3505627)

himalayan edge enterprises (BID ID -3498453)