Hazaribag Block Full Coverage Rural Water Supply Scheme on turnkey basis Under D W and S Division Hazaribag

Amount

WATER TREATMENT PLANT

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authority and Providing all labours and necessary equipment for designing & construction of Unconventional WTP of 2.10 MLD at Rola capacity. With all complete job. (Please refer to Section 5, Sl. 2.3 of SBD)

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authority and Providing all labours and necessary equipment for designing & construction of Conventional WTP of 4.80 MLD at Sundaro capacity. With all complete job. (Please refer to Section 5, Sl. 2.3 of SBD)

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authority and Providing all labours and necessary equipment for designing & construction of Conventional WTP of 4.20 MLD at Banaso capacity. With all complete job. (Please refer to Section 5, Sl. 2.3 of SBD)

Elevated Service Reservoir

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authority and Providing all labours and equipment for designing & construction of ESR all complete job. (Please refer to Section 5,Sl. 2.8 of SBD)

ESR at ROLA Capacity 5,70,000 Litres, Staging height - 18 M

ESR at SUNDARO (Sub Zone - 1) Capacity 2,20,000 Litres, Staging height - 20 M

ESR at HARLI (Sub Zone - 2) Capacity 6,50,000 Litres, Staging height - 12 M

ESR at MERU (Sub Zone - 3) Capacity 4,40,000 Litres, Staging height - 14 M

ESR at BANASO (Sub Zone - 1) Capacity 9,00,000 Litres, Staging height - 20 M

ESR at URGI (Sub Zone - 2) Capacity 90,000 Litres, Staging height - 10 M

ESR at BANHE (Sub Zone - 3) Capacity 1,40,000 Litres, Staging height - 10 M

CLEAR WATER PUMPING MACHINERY & ELECTRICAL WORKS AT ROLA WTP

Supply, installation, testing and commissioning of Centrifugal pump sets with allied equipment as under-

Horizontal Split Casing / Multi stage Centrifugal Pump :- As per IS 5120 [make: Kirloskar/ WPIL/ Mather & Platt], capable of fullfilling following requirements. mounted on common base plate and coupled with TEFC, squirrel cage induction motor (IE3), rating of motor 20% more BHP than that of pump, operating on 1500rpm, 415V, 50Hz [make: Kirloskar/ABB/Crompton Greaves/Marathon] pressure gauge, required size of sluice valve and non-return valve, standard fittings etc. including construction of MS Suction and delivery header, jointing it with Suction and Delivery line by providing required MS/CI pipes, flanges,reducer and specials, nuts bolts, packings etc. all complete as per the requirement, standards and instruction of E/I. (Contrator will again have to check the design of motor, pump & he will to get it approved by the Deptt.)

1) At Rola WTP

Discharge - 24.08 LPS, Head- 35 M. (1W+1S)

Cable: Power wiring with required 50 Sq mm, 3.5 core, 1.1KV grade, armoured cable, Standard Aluminium conductor, XLPE/PVC insulated cable from Transformer to Stablizer & Panel (MCP) including laying on wall or on floor as where required, jointing and making proper terminations,etc. all complete.

Cable: Power wiring with 3 core, 1.1 KV grade, Unarmoured cable, Standard Copper conductor, XLPE/PVC insulated cable from Panel (MCP) to Motors & Staters including laying on wall or on floor as where required, jointing and making proper terminations,etc. all complete.

Earthing: Earthing with copper earth plate including accessories and providing masanory enclosure with cover plate having locking arrangement and watering pipe of 2.7 m long etc. with charcoal / coke and salt as required conforming IS:3043.

Starter : Supplying, installation, testing & commissi-oning of assembled Fully Automatic Star Delta starter, in a provided cubical panel to operate induction motor with no volt coil, over load relay and ON/OFF push buttons, with necessary material and connected to supply, etc. all complete.

1) 20 HP Motor

Crane : Providing, erecting triple spur gear type Chain Pulley Block suitable for 3 Tonne capacity as below with 6 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per IS 3832 carrying ISI mark. With travelling trolley.

1) 50 KVA Air Cooled

Tansformer Installation: Cost of construction of DP structure in Rail / RSJ Pole for above mention transformer with different type of MS channels, M.S. angles, brackets, insulators, AB Switch, three set of horn gap fuse, DO fuse, disc & pin insulator, lightening arrester with earthing, stay sets, nut bolts, fabrication work required for the job, cost of earthing of transformer (Two nos., one no. for neutral and one for body) with all required material, technicians, labours, Grouting, PCC work, fencing, Danger board, testing of transformer oil, fitting, fixing, connecting with HT/LT lines, etc. for power supply, etc. all complete as per I.E. rules and specification of Jharkhand state electricity board.

Safety Items : Supplying, Installation and erecting of Fire extinguisher, Lightening Arrestor, emergency light, First aid box, insulation gloves & shoes, tools & tackles, rubber matting, instruction manual, etc. as per requirement and Indian standards at Pump house.

CLEAR WATER PUMPING MACHINERY & ELECTRICAL WORKS AT SUNDARO WTP

Supply, installation, testing and commissioning of Centrifugal pump sets with allied equipment as under-

Horizontal Split Casing / Multi stage Centrifugal Pump :- As per IS 5120 [make: Kirloskar/WPIL/ Mather & Platt], capable of fullfilling following requirements. mounted on common base plate and coupled with TEFC, squirrel cage induction motor (IE3), rating of motor 20% more BHP than that of pump, operating on 1500rpm, 415V, 50Hz [make: Kirloskar/ABB/Crompton Greaves/Marathon] pressure gauge, required size of sluice valve and non-return valve, standard fittings etc. including construction of MS Suction and delivery header, jointing it with Suction and Delivery line by providing required MS/CI pipes, flanges,reducer and specials, nuts bolts, packings etc. all complete as per the requirement, standards and instruction of E/I. (Contrator will again have to check the design of motor, pump & he will to get it approved by the Deptt.)

1) At Sundaro WTP, Zone - 1

Discharge - 9.04 LPS, Head- 30 M. (1W+1S)

Discharge - 45.94 LPS, Head- 120 M. (1W+1S)

Cable: Power wiring with required 300 Sq mm, 3.5 core, 1.1KV grade, armoured cable, Standard Aluminium conductor, XLPE/PVC insulated cable from Transformer to Stablizer & Panel (MCP) including laying on wall or on floor as where required, jointing and making proper terminations,etc. all complete.

Cable: Power wiring with 3 core, 1.1 KV grade, Unarmoured cable, Standard Copper conductor, XLPE/PVC insulated cable from Panel (MCP) to Motors & Staters including laying on wall or on floor as where required, jointing and making proper terminations, etc. all complete.

Earthing: Earthing with copper earth plate including accessories and providing masanory enclosure with cover plate having locking arrangement and watering pipe of 2.7 m long etc. with charcoal / coke and salt as required conforming IS:3043.

Starter : Supplying, installation, testing & commissi-oning of assembled Fully Automatic Star Delta starter, in a provided cubical panel to operate induction motor with no volt coil, over load relay and ON/OFF push buttons, with necessary material and connected to supply, etc. all complete.

1) 7.5 HP Motor

2) 120 HP Motor

Crane : Providing, erecting triple spur gear type Chain Pulley Block suitable for 3 Tonne capacity as below with 6 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per IS 3832 carrying ISI mark. With travelling trolley.

1) 250 KVA Air Cooled

Tansformer Installation: Cost of construction of DP structure in Rail / RSJ Pole for above mention transformer with different type of MS channels, M.S. angles, brackets, insulators, AB Switch, three set of horn gap fuse, DO fuse, disc & pin insulator, lightening arrester with earthing, stay sets, nut bolts, fabrication work required for the job, cost of earthing of transformer (Two nos., one no. for neutral and one for body) with all required material, technicians, labours, Grouting, PCC work, fencing, Danger board, testing of transformer oil, fitting, fixing, connecting with HT/LT lines, etc. for power supply, etc. all complete as per I.E. rules and specification of Jharkhand state electricity board.

Safety Items : Supplying, Installation and erecting of Fire extinguisher, Lightening Arrestor, emergency light, First aid box, insulation gloves & shoes, tools & tackles, rubber matting, instruction manual, etc. as per requirement and Indian standards at Pump house.

CLEAR WATER PUMPING MACHINERY & ELECTRICAL WORKS AT BANASO WTP

Supply, installation, testing and commissioning of Centrifugal pump sets with allied equipment as under-

Horizontal Split Casing / Multi stage Centrifugal Pump :- As per IS 5120 [make: Kirloskar/WPIL/ Mather & Platt], capable of fullfilling following requirements. mounted on common base plate and coupled with TEFC, squirrel cage induction motor (IE3), rating of motor 20% more BHP than that of pump, operating on 1500rpm, 415V, 50Hz [make:Kirloskar/ABB/Crompton Greaves/Marathon] pressure gauge, required size of sluice valve and non-return valve, standard fittings etc. including construction of MS Suction and delivery header, jointing it with Suction and Delivery line by providing required MS/CI pipes, flanges,reducer and specials, nuts bolts, packings etc. all complete as per the requirement, standards and instruction of E/I. (Contrator will again have to check the design of motor, pump & he will to get it approved by the Deptt.)

1) At Banaso WTP,

Discharge - 38.23 LPS, Head- 32 M. (1W+1S)

Discharge - 9.43 LPS, Head- 178 M. (1W+1S)

Cable: Power wiring with required 240 Sq mm, 3.5 core, 1.1KV grade, armoured cable, Standard Aluminium conductor, XLPE/PVC insulated cable from Transformer to Stablizer & Panel (MCP) including laying on wall or on floor as where required, jointing and making proper terminations,etc. all complete.

Cable: Power wiring with 3 core, 1.1 KV grade, Unarmoured cable, Standard Copper conductor, XLPE/PVC insulated cable from Panel (MCP) to Motors & Staters including laying on wall or on floor as where required, jointing and making proper terminations, etc. all complete.

Earthing: Earthing with copper earth plate including accessories and providing masanory enclosure with cover plate having locking arrangement and watering pipe of 2.7 m long etc. with charcoal / coke and salt as required conforming IS:3043.

Starter : Supplying, installation, testing & commissi-oning of assembled Fully Automatic Star Delta starter, in a provided cubical panel to operate induction motor with no volt coil, over load relay and ON/OFF push buttons, with necessary material and connected to supply, etc. all complete.

1) 25 HP Motor

2) 50 HP Motor

Crane : Providing, erecting triple spur gear type Chain Pulley Block suitable for 3 Tonne capacity as below with 6 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per IS 3832 carrying ISI mark. With travelling trolley.

1) 150 KVA Air Cooled

Tansformer Installation: Cost of construction of DP structure in Rail / RSJ Pole for above mention transformer with different type of MS channels, M.S. angles, brackets, insulators, AB Switch, three set of horn gap fuse, DO fuse, disc & pin insulator, lightening arrester with earthing, stay sets, nut bolts, fabrication work required for the job, cost of earthing of transformer (Two nos., one no. for neutral and one for body) with all required material, technicians, labours, Grouting, PCC work, fencing, Danger board, testing of transformer oil, fitting, fixing, connecting with HT/LT lines, etc. for power supply, etc. all complete as per I.E. rules and specification of Jharkhand state electricity board.

Safety Items : Supplying, Installation and erecting of Fire extinguisher, Lightening Arrestor, emergency light, First aid box, insulation gloves & shoes, tools & tackles, rubber matting, instruction manual, etc. as per requirement and Indian standards at Pump house.

Raw Water Rising main.

Earthwork in excavation (as per I.S. 3114/1965 for laying of different type and sizes of pipe so as to give one meter avarage cover over the socket of pipes with disposal of excavated with in initial lead and lift as per specification and direction of engineer-in charge.

Excavation in soil item-B

Earthwork in excavation of cut-off trenches by the hydraulic excavator as per designed section in soft rock (Where blasting is not needed) (vide type of soil item -C) with disposal of soil beyond 10 km from centre of trench but upto with all lifts by tipper including construction and maintenance of 1.5m haul road all complete as per specification & direction of E/I.

Gas cutting (either square cut or V cut) pipes, plates, etc. of thickness. (3.142 x Diameter of Hole i.e. Diameter of MS Pipe).

Above 10 mm. Upto 14 mm.

Lowering, laying in position to correct line and level including M. S. specials with/without any out coating such as distance pieces, straps, bends, tapers, etc. on pedestals or chairs upon formation. The rate to include loading, unloading, hoisting, marginal cutting wherever required, assembling and tack welding, and transportation upto 500M etc. complete.

1) 200 mm MS Pipe

2) 300 mm MS Pipe

Gas cutting (either square cut or V cut) pipes, plates, etc. of thickness. (3.142 x Diameter of Hole i.e. Diameter of MS Pipe).

Providing and Supplying ISI mark Confirming to IS-8329/ 2000 centrifugally cast (spun) DI pipe for water works with socket and spigot ends in standard working lengths of 4.5, 5.5 & 6 m for classification K-9 suitable for push on joint (Rubber gasket D Jointing) with cement mortar lining inside the pipes with outside zinc and bituminous coating (including cost of one gasket for each pipe) Note: - Rates are F.O.R. Jharkhand but excluding of GST.

DI K-9, Dia 200 mm

DI K-9, Dia 300 mm

Manufacturing prove supplying M.S Pipe

MS Pipe 10 mm thick, Dia 200 mm

MS Pipe 10 mm thick, Dia 300 mm

Providing and supplying ISI standard DI specials & fittings with sealing rubber gasket of SBR, complete with cast iron follower gland and MS nut bolts coated or otherwise protected from rusting and suitable for DI Pipes complete as per IS - 9523 Class K-12. Note: - Rates are F.O.R. Jharkhand but excluding of GST.

Supplying labours, tools and tackles, lubricant etc. for laying and jointing C.I. S/S tyton pipes (class LA) trenches without supplying rubber gasket (Rubber gasket confirming to I.S.S.-5382-1969) and making gasket joint including providing night guard, barrier and red light to safe guard against accident, all complete (Pipe to be supplied departmentally free of cost and laying of pipes is to be done as per I.S.S. 3114-1985) as per design, specification and direction of E/I. (without gasket)

DI K-9, Dia 200 mm

DI K-9, Dia 300 mm

Supplying labours, tools and tackles for testing of laid CI pressure pipe upto 60m head of water all complete as per specification and direction of E/I. (Water to be supplied free of cost departmently)

DI K-9, Dia 200 mm

DI K-9, Dia 300 mm

Labour charge for one cutting of C.I / D.I and specials including suppying supplying, necessary tools and plants, chipping or filling the surface finish as per specification and direction of E/I.

DI K-9, Dia 200 mm

DI K-9, Dia 300 mm

Providing Double Flanged Sluice valve confirming for IS 2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all transportation etc. complete. (without by-pass Arrangement-P.N-1.6). (With E.D)

Sluice valve, P.N. - 1.6, Dia 200 mm

Sluice valve, P.N. - 1.6, Dia 300 mm

Supplying labour and tools for fixing C.I. sluice valve in trenches with pair of C.I. Tail piece including making laed caulked joints and flanged joint as per I.S.S. specification including supplying all jointing material (pig lead confirming to I.S.S 782-1978, yarn confirming to I.S.S. 6587-1972 and nuts and bolt confirming to I.S.S. 1364-1983) including drilling holes in flanges if required as per specification and direction of E/I. (including NR Valve)

Sluice valve, P.N. - 1.6, Dia 200 mm

Sluice valve, P.N. - 1.6, Dia 300 mm

Providing and supplying ISI mark CI D/F reflux valves (non-return valves) of following dia, inspection charges, unloading from railway wagon, loading in to truck, transportation upto departmental stores, unloading, stacking etc. complete. Reflux valves as per I.S.5312 Part I (1984) without Bypass arrangement P.N. 1.6

200 mm dia Air valve P.N. - 1.6

300 mm dia Air valve P.N. - 1.6

Providing and supplying Kinetic Double Orifice type Air Valves confirming to IS 14845 as per MJP’s standard specifications combined with screw down isolating valve, small orifice elastic ball resting on a gun metal orifice nipple, large orifice vulcanite ball seating on moulded seat ring, inlet face and drilled, including insurance, third party inspection charges, loading, unloading, transportation upto departmental stores, excluding GST levied by GOI & GOM in all respect etc. complete. Kinetic Air valve flanged type. PN-1.6

80 mm dia Air valve

50 mm dia Air valve

Lowering & laying and fixing in proper alignment and position all types of CI air valve as directed by Engineer- in-charge including cost of conveyance from stores to site of work, cost of all material and giving satisfactory hydraulic testing etc. complete. (for all class of valves)

80 mm dia Air valve

50 mm dia Air valve

Supplying all materials, labours, tools and equipment and constructing brick masonry chamber of 1.20 M.x 0.90 M. x 1.50 M. inner size having 25cm. thick 75 A brick masonry wall in C.M. (1:6), over 150 mm. P.C.C. M- 150, laid over one brick flat soling on 100mm. local sand filling, including 12 mm. thick cement plaster with punning of inner surface and exposed surface of B/W in C.M. (1:6) and R.C.C. M- 150 cover slab 150 mm. thick with 20 mm. to 6 mm. graded stone chips, and clean coarse sand of F.M. 2.5 to 3 including providing CI surface box and screening shuttering, mixing, placing, striking, curing, taxes and royalty all complete as per approved design, drawing & specification and direction of E/I.

Providing P.C.C. M-150 with nominal mix of (1:3:6) in foundation with approved quality stone metal (20 mm to 6 mm Size) clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of Engineer -in charge

A) Thrust Block

For 1) 200 mm DI K-9 pipe

For 2) 300 mm DI K-9 pipe

Earthwork in back filling the trenches after laying different types and sizes of pipes with earth removed during excavation within initial lead and lift as per specification and direction of Engineer-in-Charge. (for classification of Soil item A & B).

Pure Water Rising main.

Earthwork in excavation (as per I.S. 3114/1965 for laying of different type and sizes of pipe so as to give one meter avarage cover over the socket of pipes with disposal of excavated with in initial lead and lift as per specification and direction of engineer-in charge.

Excavation in soil item-B

Earthwork in excavation of cut-off trenches by the hydraulic excavator as per designed section in soft rock (Where blasting is not needed) (vide type of soil item-C) with disposal of soil beyond 10 km from centre of trench but upto with all lifts by tipper including construction and maintenance of 1.5 m haul road all complete as per specification & direction of E/I.

Excavation in soil item-C

Providing and Supplying ISI mark Confirming to IS-8329/2000 centrifugally cast (spun) DI pipe for water works with socket and spigot ends in standard working lengths of 4.5,5.5 & 6 m for classification K-9 suitable for push on joint (Rubber gasket D Jointing) with cement mortar lining inside the pipes with outside zinc and bituminous coating (including cost of one gasket for each pipe) Note: - Rates are F.O.R. Jharkhand but excluding of GST.

DI K-9, Dia 100 mm.

DI K-9, Dia 150 mm.

DI K-9, Dia 200 mm.

DI K-9, Dia 250 mm.

Providing and supplying ISI standard DI specials & fittings with sealing rubber gasket of SBR, complete with cast iron follower gland and MS nut bolts coated or otherwise protected from rusting and suitable for DI Pipes complete as per IS - 9523 Class K-12. Note: - Rates are F.O.R. Jharkhand but excluding of GST.

100 mm to 300 mm

Supplying labours, tools and tackles, lubricant etc. for laying and jointing C.I. S/S tyton pipes (class LA) trenches supplying rubber gasket (Rubber gasket confirming to I.S.S.-5382-1969) and making gasket joint including providing night guard, barrier and red light to safe guard against accident, all complete (Pipe to be supplied departmentally free of cost and laying of pipes is to be done as per I.S.S. 3114-1985) as per design, specification and direction of E/I.

DI K-9, Dia 100 mm.

DI K-9, Dia 150 mm.

DI K-9, Dia 200 mm.

DI K-9, Dia 250 mm.

Supplying labours, tools and tackles for testing of laid CI pressure pipe upto 60m head of water all complete as per specification and direction of E/I. (Water to be supplied free of cost departmently)

DI K-9, Dia 100 mm.

DI K-9, Dia 150 mm.

DI K-9, Dia 200 mm.

DI K-9, Dia 250 mm.

Labour charge for one cutting of C.I / D.I and specials including suppying supplying, necessary tools and plants, chipping or filling the surface finish as per specification and direction of E/I.

DI K-9, Dia 100 mm.

DI K-9, Dia 150 mm.

DI K-9, Dia 200 mm.

DI K-9, Dia 250 mm.

Providing Double Flanged Sluice valve confirming for IS 2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all transportation etc. complete. (without by-pass Arrangement-P.N-1.6)(With E.D)

Sluice valve

Dia 100 mm.

Dia 150 mm.

Dia 200 mm.

Dia 250 mm.

Supplying labour and tools for fixing C.I. sluice valve in trenches with pair of C.I. Tail piece including making laed caulked joints and flanged joint as per I.S.S. specification including supplying all jointing material (pig lead confirming to I.S.S 782-1978, yarn confirming to I.S.S. 6587-1972 and nuts and bolt confirming to I.S.S. 1364 - 1983) including drilling holes in flanges if required as per specification and direction of E/I. (Including NR Value)

Sluice valve

Dia 100 mm.

Dia 150 mm.

Dia 200 mm.

Dia 250 mm.

Providing and supplying ISI mark CI D/F reflux valves (non-return valves) of following dia including railway freight, inspection charges, unloading from railway wagon, loading into truck, transportation up to departmental stores, unloading, stacking excluding GST levied by GOI & GOM in all respect etc.complete. Reflux valves as per I.S.5312 Part I (1984)

Dia 100 mm.

Dia 150 mm.

Dia 200 mm.

Dia 250 mm.

Providing and supplying Kinetic Double Orifice type Air Valves confirming to IS 14845 as per MJP’s standard specifications combined with screw down isolating valve, small orifice elastic ball resting on a gun metal orifice nipple, large orifice vulcanite ball seating on moulded seat ring, inlet face and drilled, including insurance, third party inspection charges, loading, unloading, transportation upto departmental stores, excluding GST levied by GOI & GOM in all respect etc. complete. Kinetic Air valve flanged type. PN-1.6

1) 50 mm dia.

2) 40 mm dia.

3) 25 mm dia.(Single ball flanged type)

Lowering & laying and fixing in proper alignment and position all types of CI air valve as directed by Engineer-in-charge including cost of conveyance from stores to site of work, cost of all materia and giving satisfactory hydraulic testing etc. complete. (for all class of valves)

1) 50 mm dia.

2) 40 mm dia.

3) 25 mm dia.(Single ball flanged type)

Supplying all materials, labours, tools and equipment and constructing brick masonry chamber of 1.20 M.x 0.90 M. x 1.50 M. inner size having 25 cm. thick 75A brick masonry wall in C.M. (1:6), over 150 mm. P.C.C. M- 150, laid over one brick flat soling on 100mm. local sand filling, including 12 mm. thick cement plaster with punning of inner surface and exposed surface of B/W in C.M. (1:6) and R.C.C. M- 150 cover slab 150mm. thick with 20mm. to 6mm. graded stone chips, and clean coarse sand of F.M. 2.5 to 3 including providing CI surface box and screening shuttering, mixing, placing, striking, curing, taxes and royalty all complete as per approved design, drawing & specification and direction of E/I.

Providing P.C.C. M-150 with nominal mix of (1:3:6) in foundation with approved quality stone metal (20 mm to 6 mm Size) clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of Engineer -in charge

A) Thrust Block

For 1) 100 mm Dia. DI K-9 Pipe

For 2) 150 mm Dia. DI K-9 Pipe

For 3) 200 mm Dia. DI K-9 Pipe

For 4) 250 mm Dia. DI K-9 Pipe

Earthwork in back filling the trenches after laying different types and sizes of pipes with earth removed during excavation within initial lead and lift as per specification and direction of Engineer-in-Charge (for classification of Soil item A & B).

Removable Mechanism Bulk water meter as per ISO 4054

a) 250 mm dia

b) 200 mm dia

c) 150 mm dia

DISTRIBUTION MAIN

Earthwork in excavation (as per I.S. 3114/1965 for laying of different type and sizes of pipe so as to give one meter avarage cover over the socket of pipe with disposal of excavated with in initial lead and lift as per specification and direction of engineer-in charge.

Excavation in Soil item-B

Earthwork in excavation ordinary rock or soft rock (Where blasting is not needed) (vide type of soil item -C) with initial lead of 10M, and lift of 1.5 M including dressing making the sides in proper profile profile and dressing the bed in proper grade etc. all complete as per specification & direction of E/I .

Excavation in Soil item-C

Supplying labours, tools and tackles, lubricant etc. for laying and jointing C.I.S/S tyton pipes (class LA) / D.I. trenches without rubber gasket (Rubber gasket making gasket joint including providing night guard, barrier and red light to safe guard against accident, all complete (Pipe to be supplied departmentally free of cost and laying of pipes is to be done as per I.S.S. 3114-1985) as per design, specification and direction of E/I.

100 mm dia. DI K-7

150 mm dia. DI K-7

200 mm dia. DI K-7

250 mm dia. DI K-7

300 mm dia. DI K-7

350 mm dia. DI K-7

Supplying labours, tools and tackles for testing of laid CI or U.P.V.C. OR H.D.P.E. OR A.C. pressure pipe upto 60m head of water all complete as per specification and direction of E/I. (Water to be supplied free of cost departmently)

100 mm dia. DI K-7

150 mm dia. DI K-7

200 mm dia. DI K-7

250 mm dia. DI K-7

300 mm dia. DI K-7

350 mm dia. DI K-7

Cutting and champhering of pipes of following diameters including cost of all materials and labour involved,etc. complete as directed by Engineer-in-charge (for all class of pipes)

100 mm dia. DI K-7

150 mm dia. DI K-7

200 mm dia. DI K-7

250 mm dia. DI K-7

300 mm dia. DI K-7

Supplying labour and tools for fixing C.I. sluice valve in trenches with pair of C.I. Tail piece including making laed caulked joints and flanged joint as per I.S.S. specification including supplying all jointing material (pig lead confirming to I.S.S 782-1978, yarn confirming to I.S.S. 6587-1972 and nuts and bolt confirming to I.S.S. 1364-1983) including drilling holes in flanges if required as per specification and direction of E/I.

Sluice Valve

100 mm dia.

150 mm dia.

200 mm dia.

250 mm dia.

300 mm dia.

350 mm dia.

Supplying all materials, labours, tools and equipment and constructing brick masonry chamber of 1.20 M.x 0.90 M. x 1.50 M. inner size having 25 cm. thick 75 A brick masonry wall in C.M. (1:6), over 150 mm. P.C.C. M- 150, laid over one brick flat soling on 100 mm. local sand filling, including 12 mm. thick cement plaster with punning of inner surface and exposed surface of B/W in C.M. (1:6) and R.C.C. M- 150 cover slab 150mm. thick with 20mm. to 6 mm. graded stone chips, and clean coarse sand of F.M. 2.5 to 3 including providing CI surface box and screening shuttering, mixing, placing, striking, curing, taxes and royalty all complete as per approved design, drawing & specification and direction of E/I.

Cutting the road as well as restoring the same as per specifications and as directed by Engineer incharge

Pucca Road (Except black top only taken out material to be used) 40%

Waterbound Macadam road(taken out material will be used) for cutting as per requirement 30% of the restoring work

Dismantaling plain cement or lime concrete work including stacking serviceable materials in countable stacks within 15 meter lead and disposal of unservisible materials with all leads complete as per direction of E/I

Providing PCC M-150 in nominal mix of (1:2:4) in foundation with approved quality of store chips 20 mm-6 mm size graded and clean coarsed sand of FM 2.5 to 3.0 including screeing shuttering mixing cement concrete in mixer and placing in position vibrating striking curing taxes and royalty alll complete as per building specification and directio of E/I.

Earthwork in backfilling the trenches after laying different types and size of pipes with earth removed during excavation within initial lead and lift as per specification and direction of Engineer-in-charge.

Providing and Supplying ISI mark Confirming to IS-8329/2000 centrifugally cast (spun) DI pipe for water works with socket and spigot ends in standard working lengths of 4.5,5.5 & 6 m for classification K-7 suitable for push on joint (Rubber gasket D Jointing) with cement mortar lining inside the pipes with outside zinc and bituminous coating (including cost of one gasket for each pipe) Note: - Rates are F.O.R. Jharkhand but excluding of GST.

100 mm dia. DI K-7

150 mm dia. DI K-7

200 mm dia. DI K-7

250 mm dia. DI K-7

300 mm dia. DI K-7

350 mm dia. DI K-7

Providing and supplying ISI standard DI specials & fittings with sealing rubber gasket of SBR, complete with cast iron follower gland and MS nut bolts coated or otherwise protected from rusting and suitable for DI Pipes complete as per IS - 9523 Class K-12. Note: - Rates are F.O.R. Jharkhand but excluding of GST.

100 - 300 mm Dia.

350 - 450 mm Dia.

Providing double flange sluice valve confirming for IS- 2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all taxes transportation complete. (Sluice and scour valve ) Without by pass arrangement PN-1 with ED

Sluice Valve

100 mm dia.

150 mm dia.

200 mm dia.

250 mm dia.

300 mm dia.

350 mm dia.

Bulk Meter - Providing, installing and giving satisfactory field testing of bulk water meter, horizontal inferential multijet type with magnetic drive and dry dial suitable for ambient 50º C Temperature duly sealed against tampering complete with flanges at both ends and conforming to class B as per ISO 4064 along with manufacturer's test certificate and guarantee certificate, including cost of all materials and labour etc with OIML. MID certification for Abroad meter and FCRI for India including 36 months guarantee etc complete.

a) Removable mechanism type Bulk water meter as per M ISO 4064

150 mm dia.

200 mm dia.

250 mm dia.

300 mm dia.

350 mm dia. Full Bore Electromagnetic flow meter

Twin Type Staff Quarter - 3 Unit (Please refer to Section 5, Sl. 2.7 of SBD)

E/W in Excavation in foundation trenches in ordinary soil (Vide classification of soil Item -A) & disposal of excavatd earth obtained to a distance up to 50 M including all lift leveling ramming the foundation trenches removing root of trees scrubs all complete as per approved design.

Providing, coarse clean sand in filling in foudation trenches /in Plinth including ramming & watering in layers not exceeding 150 mm thick with all leads lift including cost of all materilas, labour, royalty & taxes all complete as per building specification & direction of E/I

Providing designation 75 A one brick flat soiling joints filled with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I

Providing P.C.C M-100 in nominal mix of (1:3:6) in foundation with appoved quantity of stone metal (50 mm 25 mm dia size)graded & clean coarse sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer & placing in position, vibrating, striking, curing taxes & royalty all complete as per building specification & direction of E/I.

Providing designation 75 A brick work in C.M. (1:6) in foundation 7 Plinth with approved quality of clean coarse sand of F.M 2 to 2.5 including Providing 10 mm thick mortar joints, Cost of screening, materials, Scaffolding, raking out joints to 15 mm depth curing, taxes & royalty all complete as per building specification & direction of E/I

Providing 50 mm thick damp proof coarse with cement concrete M-150 with nominal mix of (1:2:4) with approved quality of stone chips of 20 mm to 6 mm size graded and clean coarse sand of F.M 2.5 to3 including screening, shuttering mixing cement concrete in mixer with 5% cico or any other approved water proffing compound and placing in position, vibrating, striing, curing, taxes & royalty all complete as per building specification & direction of E/I

Providing designation 75 A brick work in C.M (1:6) in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing10 mm thick motar joints, cost of screening, materials, scaffolding, raking out joints to 15 mm depth curing, taxes & royalty all complete as per building specification & direction of E/I.

Providing R.C.C M-150 with nominal mix of (1:2:4) in lintel level with approved quality of stone chips 20 mm to 6mm size graded & clean coarse sand of F.M 2.5 to including screening, centring, shuttering and mixing cement concrete in mixer & placing in position vibrating striking curing (but excluding the cost of reinforcement ) taxes & royalty all complete as per building specification of E/I.

Providing average 63 mm thick R.C.C M -200 with nominal mix (1:1.5:3) chajja in shelves with approved quality of stone chips 20 mm to 6 mm size graded & clean coarse sand of F.M 2.5 to 3 including making drip course in concrete, screening, centering shuttering & mixing cement concrete in mixer & placing in position vibrating, striking, 6 mm cement plaster (1:4) in celling & sides of chajja with sand of F.M 1.5, Curing (But excluding the cost of reinforcement) taxes and royalty all complete as per building specification of E/I.

Providing R.C.C M-200 with nominal mix of (1:1.5:3) in roof slab with approved quality of stone chips 20 mm to 6 mm size Graded & Clean coarse sand F.M 2.5 to including making drip course in cocrete, screening, concreting, shuttering, centring mixing cement concrete in mixer & placing in position, vibrating, striking, curing (but excluding the cost of reinforcement) taxes & royalty all complete as per building Specification & direction of the E/I.

Supplying fitting & fixing good quality, well dressed & well seasoned sal wood work in choukhat in doors, windows, skylights, fan light and C/W celestial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls & lintels all complete as per building specification & direction of E/I

Supplying fitting and fixing 250 x 20 x 6 mm L-type M.S Clamp properly fish tailed .including making holes and setting the same in 375 x 125 x 75 mm cement concrete block (1:2:4) with cost of all labour and materials and taxes as per building specification and diection of E/I @6 for each door & 4 for each window Total Quantity -(2x3x6+2x4x4)=68 nos

Supplying all materials, labours and fitting & fixing 38 mm (1.5) thick good quality seasoned sal wood battened shutter ledged & braced in door and windows with oxidized iron fitting such as hingles, sliding door bolts, tower bolts, handles or ings hooks and eye, cleats, sand block as per schedule, taxes & royalty all complete as per building specification & direction of Engineer -in- charge

Supplying, fittings & fixing M.S Gril made of 20 x 6 mm M.S flat as per approved design & drawing properly fabricated with joints continous filllet welded and finshed smooth, carriage of grill to work site hoisting as per the building specification and direction of E/I (where materials is not supplied by the Deptt.)

Providing 25 mm thick pre cast R.C.C M-200 with nominal mix of (1:1.5:3) in jali with approved quality to stone chips of 6mm nominal size and clean coarse sand of FM 2.5 to 3 with 1.6 mm thick M.S wire as per approved design and drawing and placing the same in position true to plumb and level and properly grouted with cement mortar (1:3) including cost of curing, Scaffolding and finishing all complete as per building specification and direction E/I

Providing and fixing fan hook of 16 mm dia M.S bar 1 meter long bent to reqired size and shape placed in position and fixing in R.C.C slab/beam at the time of casting all complete as per building specification of E/I where material is not supplied by cheet

Supplying, fitting and Fixing M.S Grill gate made of 20 x 6 mm M.S or 16 mm M.S raurbar Flat fitted on 25 mm x 25 mm x 6mm M.S angle frame of size 60 x 60 x 6 as per approved design including cost of fabrication & drawing, properly fabricated with joints continuous fillet welded & finished smooth, providing necessary locking arrangements with Haskell & dummy duly fixed in C.C (1:2:4) blocks of reuired size applying a priming red lead paints over steel works, taxes , carriage of grill to work site, as per the building specification & direction of E/I (where materials is not supplied by the Dept)

Providing 6 mm thick cement plaster (1:4) in celling with approved quality of clean coarse sand of F.M 1.5 including screening, curing with all leads & lifts of water, scaffolding, taxes & royalty all complete as per building specification & direction of E/I

Providing 12 mm thick cement plaster (1:6) with approved quality of clean coarse sand of F.M 1.5 including screening Curing with all leads & lifts of water, Scaffolding, taxes 7 royalty all complete as per building specification & direction of E/I.

Providing cement 1:3 (12mm ) plaster with cement mortar (1:3) using clean coarse sand finishing with neat punning a dado 6" (150 mm) high a side room and out side wall upto plinth level includng screening, curing with all leads & lifts of water, scaffolding, taxes and royalty all complete as per building specification & direction of E/I

Filling in foudation trenches & Plinth in layers not exceeding 150 mm thick well watered, rammed, fully compacted & fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 m & lift of 1.5 m all complete as per building specification & direction of E/I. (Mode of measurement compacted volume)

Providing average 150 mm thick dry rammed khoa beaten to 112 mm. (compacted with water) made of well burnt or jhama bricks including ramming properly till compacted thickness is achieved, curing & carriage of water with all leads, making proper slope & blending the top with cement mortar (1:10) all complete as per building specification & direction of E/I.

Providing 25 mm thick First class patent stone flooring (1:2:4) with stone chips in two layers ,bottom layer 19 mm thick (1:2:4) with 12 mm to 6 mm size graded stone chips and top layer 6 mm thick (1:2) with 6 mm down stone chips in pannels including cost of curing , finishing the surface smooth by rubbing with carborandum stone taxes & royalty with all complete as per building specification & direction of E/I

Providing designation 75 A one brick on edge flooring in C.M (1:4) with top surface flush pointed in CM (1:4) approved quality of clean coarse sand of F.M 2 to 2.5 including the cost of screening, raking out joints to 15 mm depth, curing taxes, royalty all complete as per building specification and direction (E/I)

White washing three coat over new surface with approved quality of lime including cost of cleaning surface thoroughly and removing the scales of smoke & ash marks with jhama rubbing, scaffolding washing of floor sand taxes all complete as per building specification and direction of E/I

Providing all materials, labours & doing 2 (two) coat colour washing over a coat of white washing over new surface with approved quality of lime & colour over the new surface including the cost of clening surface thoroughly and removing the scales of smoke & ash marks with jhama rubbing, scaffolding washing of floor sand taxes all complete as per building specification and direction of E/I.

Providing two coats of painting with readymix paint synthetic enamel paint over a coat of primer of approved shad and make over new wooden surface after cleaning, removing dirt scales, smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification & direction of E/I.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing rust, dirt, scales, smokes and grease and cleaning the surface thouroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I

Providing 2(two) coats of Paniting with ready mixed paints of approved shade & make over steel surafce including cleaning the surface thouroughly, scaffolding & taxes all complete as per building specification & direction of E/I

Providing 10 mm (TMT) Fe 500 TOR for steel reinforced as per approved design and drawing excluding carriage of tor rod to work site including cutting bending and binding with annealed wire with cost of wire with cost of wore removal of rust placing the rods in position all complete as per building specification and direction of E/I.

Carriage of materials from divisional store or kiln site or quarry site to work site including contract profit, loading, unloading, transportation, etc. all complete .

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Bricks 06 KM lead

Stone/Stone Chips 11 KM lead

Water Supply Sanitation Installation (Plumbing work)

Supplying and laying GI pipes of approved make in trenches with red lead and yarn with socket and screw joints and cutting pipes in size and threading ends where necessary including carriage of materials up to work site etc. all complete as per specification and direction of E/I.

i) 25mm GI. Pipe.

ii) 15 mm GI. Pipe.

Supplying materials and labours for fixing GI Pipes with red lead paints and yarn with screwed and sockted joints on wall, celling and floor including supplying of wall hooks of pipe clamp, wooden plugs, cutting pipe to size and threading ends where necessary all complete as per specification and direction of E/I.

i) 15 mm GI. Pipe

Supplying, fitting and fixing of GM ferrule of approved make in DI/CI main including drilling and tapping CI/DI main etc. all complete as per specification and direction of E/I.

Supplying and fixing GI fittings of approved make all complete as per direction of E/I.

(a) Elbow 15 mm dia

(b) Tee plane 15mm dia

(c) Nipple 15mm dia.

(d) Union Socket 25mm dia

(e) Union Socket 15mm dia

(f) Brass bib cock 15mm dia

(g) C.I stop cock 15mm dia

(h) C.I. stop cock 25mm dia

(i) Reducing Socket 25x15mm

(j) Tee 25x25x15mm dia

Supplying, fitting and fixing vitreous white glazed earthen were I W C of parry Hindustan or any other I.S.S approved make with 100 mm HCI ‘P’ trap, 15 Liters CI pull and let go flushing cistern of names or other ISS equivalent make complete with all fittings C.I. or C.C brackets, 32 mm, alkathene /PVC telescopic flush pipe about 2 mtrs. long with one brass coupling and clamps, GI chain and pull including supplying and fixing a pair of vitreous white glazed earthen were footrest to be fixed in floor, 15 mm .CI body brass spindle, stop cock of weight not less than 50 grams, 15 mm. PVC connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. (510mm.long with 12.5 Liter low level PVC System).

SEPTIC TANK and SOAK PIT

Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item - B) and disposal of excavated earth as obtained to a distance up to 50 m including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/I.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of E/I.

Providing designation 75A one Brick flat soling, joints filled with local sand including cost of watering, tax, royalty all complete as per building specification and direction of E/I.

Providing P.C.C M150 with nominal mix of (1:2:4) in foundation with approved stone chips 20mm to 6mm size well graded and clean course sand of FM-2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, Vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing water proof cement plaster (1:3) with clean course sand of F.M- 1.5mm with 5% cico or any other approved water proofing compound including taxes and royalty all complete as per building specification and directions of E/I.

(a) 19 mm thick

(b) 12 mm thick

Providing designation 75A bricks work in C.M. in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. thick mortar joints, cost of screening materials racking out joints to 15 mm. depth, curing taxes and royalty all complete as per building specification and direction of E/I.

(a) B/W in C.M (1:4)

(b) B/W 75-B in (1:6) for Soak pit

(c) Brick work in dry masonry for soak pit.

Providing pre cast R.C.C. M-150 with nominal mix of (1:2:4) slab of desired size with approved quality of stone chips and clean coarse sand of FM 2.5 to 3 including curing, shuttering, carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement), taxes and royalty etc. all complete as per building specification and direction of E/I.

Providing for reinforcement as per approved design and drawing excluding carriage of tor rod to work site including cutting bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per Specification and direction of E/I.

10 mm dia

Supplying fitting and fixing H.C.I. Pipe/ H.C.I. fitting of Approved make confirming to I.S.S 1729 including supplying nails and bobbins lead and yarn from making lead caulked joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/I.

(a) 100mm dia H.C.I. Tee.

(b) 100mm dia H.C.I. Band

(c) 50mm dia H.C.I. Cowel

(d) 50mm dia H.C.I. Vent pipe

(e) 100mm H.C.I. Pipe

Supplying materials and labours and fixing 20mm dia M.S bar steps in wall of 0.3 m interval and staggered in (1:2:4) cement concrete including scaffolding and curing etc. all complete as per specification and direction of E/I.

Supplying all materials, labours, tools and tackles and 100mm dia R.C.C hume pipe and laying jointing, testing, earth work including carriage of materials etc. all complete.

Supplying 50mm size brick bats and filling in soak pit including carriage and labours etc. all complete as per direction of E/I.

Supplying materials and labours for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600x450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600x475mm G.I. Cover With frame (Weight not less than 36 Kg.) along with earth work in excavation and 80mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I

Carriages of materials

(a) Brick – 06 KM lead

(b) Sand - 36 KM lead

(c) Stone chips - 11 KM lead

(d) Steel - 10 KM lead

(d) Cement- 10 KM lead

Electrical Works

Point wiring in PVC conduit with modular type switch wiring for light point /fan point with 1.5 sqmm F.R. PVC insulated copper conductor single core cable in surface/ recessed PVC conduit with modular switch modular plate, suitable G.I. box and the point with sqmm FR PVC insulated copper conductor single core cable etc as required

Wiring for twin control light point with 1.5 sqmm F.R. PVC insulated copper conductor single core cable in surface/recessed PVC conduit with two way modular switch modular plate, suitable G.I. box and the point with sqmm FR PVC insulated copper conductor single core cable etc as required

Wiring for light /power plug point with 2 x 4 sqmm F.R.PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with one no 4 sqmm FR PVC insulated copper conductor single core cable for loop earthing etc as required.

Copper sub main wiring in PVC conduit Wiring for sub main wiring with PVC insulated copper conductor single core in surface/recessed PVC conduit as required.

2 x 1.5 sqmm + 1 x 1.5 sqmm earth wiring

2 x 2.5 sqmm + 1 x 2.5 sqmm earth wiring

Supplying and fixing following way three pole and neutral sheet MCB distribution board 415 volts on surface/ recessed complete with tinned copper bush bars, neutral link, earth bar, din bar, detachable gland plate inter connection phosphatised and power painted including earthing etc as required (but with out mcb / rccb / Isolator) (4+12) double door horizontal type.

Supplying and fixing 5 amp to 32 amp, rating 240 volts, B series miniature circuit breaker of single poles in existing MCB DB complete with connecting, testing, and commissioning etc as required

Earthing with G.I. earth pipe 4.5 M long 40mm dia including accessories and providing masonry enclosure with copper plate having locking arrangement and watering pipe etc with charcoal, salt all complete as per electrical rule

Supplying ,fitting and fixing following sizes of PVC conduct along with accessories in surface / races including cutting the wall and making good the same in case of recessed conduit as required

PVC con 20 mm PVC pipe

PVC con 25 mm PVC pipe

Installation commissioning and testing Ceiling Fan

Carriage of ceiling fan and regulator

Supplying, fitting and fixing 5 amp ceiling rose on the existing junction

Supplying, fitting and fixing breas batten/ angle holder including connection etc.

Supplying, fitting and fixing G.I. box with modular plate and cover in front of surface or in recess including providing and fixing 3 pin 5/6 amp modular type switch, connection, painting etc as required.

Supplying, fitting and fixing G.I. box with modular plate and cover in front of surface or in recess including providing and fixing 6 pin 5/6 amp and 15/16 amp socket outlet and 15/16 amp modular type switch, connection, painting etc as required.

Supplying and drawing co-axial T.V. cable RG-06 grade 0.7 nn solid copper conductor PE insulated seilded with fine tinned cover braid and protected with PVC sheath in the existing surface / recessed steel/ PVC conduit as required.

Supplying and fixing modular switch / socket on the existing modular plate and switch box including connection but excluding modular plate etc,as required. TV antenna socket out put

Supplying, fitting and fixing modular base and cover plate on existing modular metal boxes etc as required.

Cost of Earthing with G.I. earth pipe 4.5 M long 40mm dia G.I.Pipe 600 mm x 600 mm x 6 mm thick copper earth plate and 8 SWG copper wire including cost of making 1.2 x 1.2 x 3m deep pit and filling with charcoal, salt all complete as per electrical rule

Boundry Wall for 3 Nos. WTP & 7 Nos. ESR. (1884.00 M Long)

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authority Construction of Compound wall. etc. all complete job. (Please refer to Section 5,Sl. 2.9 of SBD)

Earth work in excavation in foundation trenches in hard soil (Vide classification soil item B) and disposal of excavated earth as obtained to a distance up to 50 Mtr including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, specification and direction of E/I.

Providing coarse clean sand in filling in fundation trenches or in plinth including ramming and watering in layers not exceeding 15mm thick with all leads and lifts includiing cost of all materials, labour, royality and taxes all complete as per building specification and direction of E/I.

Providing designation of 75A one brick flat soling, joints filled with local sand including cost of watering, taxes royalty all complete as per building specification and direction of E/I.

Providing P.C.C M - 150 with nominal mix of (1:2:4) in foundation with approved quality of stone chips (20 mm to 6 mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing R.C.C M - 200 with nominal mix of (1:1.5:3) in foundation with approved quality of stone chips (20mm to 6mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Centering & Shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in stiffeners with approved quality of stone chips 20mm to 6 mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I.

Centering & Shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in band at plinth level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I. Top of Wall

Centering & Shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in band at lintel level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I. Top of Wall

Centering & Shuttering

Providing designation 75 A brick work in CM (1:6) in super structure with approved quality of clean coarse sand of FM 2 to 2.5 including, providing 10mm thick mortar joints cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of FM 1.5 including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per specification and direction of E/I.

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification & direction of E/I. Qnty. Same as Item no.13

Providing Tor steel reinforcement of 10 mm,12 mm, &16 mm dia Bars as per approved design and drawing excluding carriage of M.S bars to work site, cutting, bending and binding with annealed wire with cost of wire ,removal of rust, Placing the rods in position all complete as per building specification and direction of E/I.

Filling in foundation trenches and plinth in layers not exceeding dressed with earth obtained from excavation of foundation trenches with a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I.

Carriage of materials from divisional store or kiln site or quarry site to work site including contractor's profit, loading, unloading, transportation etc. all complete .

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Stone/Stone Chips 11 KM lead

Bricks 06 KM lead

Gate - 10 Nos.

Earth work in excavation in foundation trenches in hard soil (Vide classification soil item B) and disposal of excavated earth as obtained to a distance up to 50 Mtr including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, specification and direction of E/I.

Providing coarse clean sand in filling in fundation trenches or in plinth including ramming and watering in layers not exceeding 15mm thick with all leads and lifts includiing cost of all materials, labour, royality and taxes all complete as per building specification and direction of E/I.

Providing designation of 75 A one brick flat soling, joints filled with local sand including cost of watering, taxes royalty all complete as per building specification and direction of E/I.

Providing P.C.C. M - 150 with nominal mix of (1:2:4) in foundation with approved quality of stone chips (20 mm to 6 mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing R.C.C M - 200 with nominal mix of (1:1.5:3) in foundation with approved quality of stone chips (20mm to 6mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Centering & Shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in column with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I.

Centering & Shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in band at plinth level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I. Top of Wall

Centering & Shuttering

Providing Tor steel reinforcement of 10 mm, 12 mm & 16 mm dia Bars as per approved design and drawing excluding carriage of M.S bars to work site, cutting ,bending and binding with annealed wire with cost of wire, removal of rust, Placing the rods in position all complete as per building specification and direction of E/I.

Filling in foundation trenches and plinth in layers not exceeding dressed with earth obtained from excavation of foundation trenches with a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I.

Supplying fitting & Fixing M.S. grill gate with M.S. grills made 20 x 6 mm M.S. flat or 16 mm M.S. square bars fitted 25 x 25 x 6 mm M.S. angle frame of size 60 x 60 x 6 mm including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.

Providing two coat of painting with ready mixed paint of approved shade and make over steel surface

Carriage of materials from divisional store or kiln site or quarry site to work site including contractor's profit, loading, unloading, transportation etc. all complete .

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Stone/Stone Chips 11 KM lead

Bricks 06 KM lead

Highway Crossing

Manufacturing providing and supplying spirally welded/ ERW/SAW/Fabricated M.S. Pipes (Commercial Quantity) including procurements of Plates. Gas cutting to required size rolling tack welding assembling in suitable lenghths to form pipes, welding on automatic welding machine and forming 'v' edge on both ends of pipe including all taxes (Central and Local), railway freight, Insurance unloading form railway wagon, loading into truck transport to stores/site, unloading, stacking etc. complete as per IS-3589 and IS-5504 as applicable as per specifications (No negative tolerance in thickness is permissible).

1) Diameter of Casing Pipe = 323.9 mm dia (O.D.)

Thickness of Pipe = 9.5 mm

(For Casing of PWRM of Dia = 150 mm)

Length of Crossing = 20 m

2) Diameter of Casing Pipe = 508 mm dia (O.D.)

Thickness of Pipe = 10 mm

(For Casing of PWRM of Dia = 300 mm)

Length of Crossing = 20 m

3) Diameter of Casing Pipe = 406 mm dia (O.D.)

Thickness of Pipe = 10 mm

(For Casing of Distribution Pipe of Dia = 250 mm)

Length of Crossing = 20 m

4) Diameter of Casing Pipe = 323.9 mm dia (O.D.)

Thickness of Pipe = 9.5 mm

(For Casing of Distribution Pipe of Dia = 150 mm)

Length of Crossing = 20 m

5) Diameter of Casing Pipe = 355.7 mm dia (O.D.)

Thickness of Pipe = 9.5 mm

(For Casing of Distribution Pipe of Dia = 200 mm)

Length of Crossing = 20 m

6) Diameter of Casing Pipe = 323.9 mm dia (O.D.)

Thickness of Pipe = 9.5 mm

(For Casing of Distribution Pipe of Dia = 150 mm)

Length of Crossing = 20 m

7) Diameter of Casing Pipe = 323.9 mm dia (O.D.)

Thickness of Pipe = 9.5 mm

(For Casing of Distribution Pipe of Dia = 150 mm)

Length of Crossing = 20 m

8) Diameter of Casing Pipe = 323.9 mm dia (O.D.)

Thickness of Pipe = 9.5 mm

(For Casing of Distribution Pipe of Dia = 100 mm)

Length of Crossing = 20 m

Pushing of M.S.pipe of following dia for road crossing and Raiway crossing by push through method in all types of strata by using hydraulic jack and drilling machine of required diameter below 3.0 m depth including lowering, laying, jointing of M.S. casting pipe including cost of labour, fuel and material, required welding machinery, tripod, chain pulley block crane, blower, etc. ransportation and dewatering etc. complete as directed by Engineer in charge but excluding cost of M.S. pipe.

1) 300 mm to 450 mm dia M.S. Pipe

2) 450 mm to 600 mm dia M.S. Pipe

Providing and applying graphite of apprived prime of first inferol 49 W emaline 05/58 pipe cost or any other equivelent approved pain to the internal surface of pipe line at sight.

1) For 323.9 mm Dia.

3.142 x 100.00 m x 0.3239 = 101.77 Sqm

2) For 355.7 mm Dia.

3.142 x 20.00 m x 0.3557 = 22.35 Sqm

3) For 406 mm Dia.

3.142 x 20.00 m x 0.406 = 25.51 Sqm

4) For 508 mm Dia.

3.142 x 20.00 m x 0.508 = 31.92 Sqm

Total = 181.56 Sqm

First Coat

Second Coat

House Connection for 16817 Nos. Consumer.

Earth work in excavation (as per I.S. 3114/ 1965 for laying of different types and sizes of pipes so as to give 1 m av. cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of E/l. (For soil item B)

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l. (Mode of measurement complacted volume).

Provinding P.C.C M-150 with in norminal mix of (1:2:4) in foundation with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of F.M 2.5 to 3 including, screening, shuttering, mixing cement concrete in mixture and placing in position vibrating striking curing taxes and royality all complete as per building specifiaction and direction of E/I.

Earth work in back fillingthe trenches after laying of different types and sizes of pipes with earth removed during excavation within initial lead and lift as per specification and direction of E/I. (For soil item A & B)

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing and supplying blue MDPE pipes confirming to ISO 4427:1996 manufactured from vergin resin PE 80 food grade compounded raw material having blue colour only assurance certificate from quality agencies like WRC / CIPET ( India) / DVGM / KIWA / SPGN etc. for usage in drinking water with quality system. The cost shall including cost all taxes, inspection charges transprotaion to work site and earth work involved, all complete job as per specification and direction of E/I. 20 mm dia pipe.

Providing and supplying G.I. pipes (Tata and equivalent make) for usage in drinking water with quality system, The cost shall include testing of all materials all taxes central, State, Municipal, Inspection charges transportation up to site transite insurance, loading, unloading, stacking etc. complete as specified and directed.

Lowering laying and jointing HDPE / MDPE pipe in proper position including all specials by Compression fitting / Electrofusion and But fusion jointing procedure including hydraulic testing as er relevent IS Code complete with all materials for jointing procedure like Electro-fusion machine, Electric mirrior/ heater/But fusion welding machine with hydraulic testing and all labours as directed by engineer in charge as per IS-7634 part II

Supplying labour and tools for fixing G.I. pipes with Red lead and yarn of following nominal bore with screwed and socketted joints on wall, ceiling and floor including supplying and fitting of wall hooks or pipe clamps, wooden plugs, cutting pipes to size and threading ends if required etc. all complete as per specification and direction of E/l. (Pipe with socket to be supplied deparmentally free of cost).

Supplying and fixing G.M. ferrule of approved make in existing C.I./D.I. main including drilling and taping C.I./D.I. main all complete as per specification and direction of E/I. 3 mm, 6 mm 10 mm dia ferrule weight not less than 425 gram

Providing and fixing gun metal full way valve of approved quality all complete as per specification and direction of E/ (a) 20 mm dia and weight not less than 400 gram.

Providing and fixing 15 mm Dia male ended C.I Body Brass Spindle valve and seat bib cock of approved quality (Wt.not Less than 400 gms.) with extra socket all complete as per specification and Direction of E/I.

Supplying and fixing G.I. fittings of Approved make all complete as per specification and Direction of E/I

Elbow 20 mm

Elbow 15 mm

Reducing Socket 20 mm

Nipple 20 mm

Nipple 15 mm

Union Socket 20 mm

Socket 15mm

Socket 20 mm

Carriage of materials

Operation & Maintenance for Five years

O/M work with Labour component & Materials for 1st Year

As per SBD Section - 5 Clouse 9.10

O/M work with Labour component & Materials for 2nd Year

As per SBD Section - 5 Clouse 9.10

O/M work with Labour component & Materials for 3rd Year

As per SBD Section - 5 Clouse 9.10

O/M work with Labour component & Materials for 4th Year

As per SBD Section - 5 Clouse 9.10

O/M work with Labour component & Materials for 5th Year

As per SBD Section - 5 Clouse 9.10

Add @ 9% CGST

Add @ 9% SGST

Add @ 1% Labour Cess

Surajmal Onkarmal