ADDN / ALTN TO BUILDING NO. P-184 (UNIT QUARTER GUARD) AT 1 AFSR AT AF STN PALAM UNDER GE (AF) PALAM, DELHI CANTT - 10

Amount

Taking down chowkhat or frame with shutters (without taking off shutter from the frame) area n exc. 1.5 sqm each complete all as specified and as directed.

Taking down chowkhat or frame with shutters (without taking off shutter from the frame) area exc. 1.5 sqm but n exc 4.0 sqm each complete all as specified and as directed.

Taking down shutter of any description area exc 1 sqm and not exc 2 sqm each complete all as specified and as directed.

Demolition of concrete in ground floor and pavings n.exc 15 cm thickness below or above ground level complete all as specified and as directed.

Dismantling structural steel work including door, gates but excluding framed truss etc. complete all as specified and as directed.

M & L for removing loose, disturbed or disintegrated old concrete surfaces of RCC beam, column, lintel, slab, chhajja, pardi, railing etc, cleaning thoroughly exposed reinforcement, by sand blasting using suitable pump as directed by the GE, preparing exposed concrete surfaces to receive guniting, applying one coat of anti corrosive paint to the exposed reinforcement, supply and fix welded wire mesh of size 100 x 100 mm of 3 mm dia wire, weight not less than 1.37 Kg/Sqm & binding with 22 guage mild steel (annealed) binding wire to reinforcement and applying pressure guniting in cement mortar 1:3, average 30mm to 50mm thickness and thereafter rendering 10 mm thick plaster in cement mortar (1:3), mixed with water proofing compound @2% by weight of cement and finishing the surfaces even and smooth without using extra cement to match with the existing surfaces, removing the debris outside MD land including material and labour for necessary scaffolding and formwork (G+3 storeys) and safety arrangement for guniting work complete all as specified and directed. Note:- The finish of the surfaces shall be matched with the existing surface. WPC shall be measured & paid separately under respective item as supply only.

Taking down cement plaster or cement lime plaster on brick or stone walls etc including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed.

M&L for 10mm thick plaster on fair faces of brick work or concrete surfaces in cement mortar (1:3) as in ceilings, surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:6), surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:4), surface finished even and fair mixed with water proofing compound by weight as per manufacturer's instructions including necessary scaffolding up to (G+3 storey) complete all as specified and as directed. Note:- WPC shall be measured and paid separately under respective items of BOQ.

Excavation over areas in trenches n exc 1.5 m deep and getting out hard / dense soil complete all as specified and as directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick as in soft/loose soil complete all as specified and as directed.

Removing excavated surplus soil/ material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggragates) as in foundation, mass concrete and filiings complete all as specified and as directed.

S&F factory made PVC door frame of size (50mmx47mm) made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification and drawing complete all as specified and as directed.

Supply and fixing for factory made Solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC shets for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail panelling of plain colour PVC shet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete all as specified and as directed.

S&F 12mm thick entrance glass door at alley way with one way visibility, locking arrangement necessery unit insignia embossed (unit symbol) on glass as per sample approve by user unit with all fitting and fixtured complete of and glass partition above shutter to roof level inculiding fancy type handle , locking arrangement , springs , door closer and aluminium frame work inculiding suitable beading and with necessary electrical fittings etc complete all as specified and directed .Note: Quoted rate shall be inclusive of aluminium sections

S&F rolled mild steel grade Fe-290 Gde-E-165 quality-A as in framed work as in doors or gates of angle or other section gates of with gusset plates, rails, cladding, chowkhats/frame or like etc welding hold fast, hinges complete all as specified and as directed.

S&F 1mm thick plain, black, mild steel sheeting, as in doors / gates, ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) complete all as specified and as directed.

S&F 35 mm thick flush shutter solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

M&L for 2nd class hard wood factory made 35mm thick glazed and skelten shutters open repated and prepared for door to receive framing plain chamfered or rounded fitted with cut and mitered beads for securing glass/wire mesh etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a)of shutter with sash bar complete all as specified and as directed.

S& F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

S&F powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed.

S&F powder coated aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and as directed.

S&F powder coated aluminium three track sliding type glazed window shutter with 5 mm thick plain sheet glass fixed open track section (100x38x1.5)mm having three track (two of glass & one of stainless steel wirecloth of 0.36mm nominal dia of wire and average width of aparture 1.40mm) with members of window shutters of section (38x12x1.5)mm and other standard sliding section including all necessary fiber wheel rollers suitable handls to facilitate sliding and all necessary jointing cleats, glazing clips, rubber packing, aluminium snap beading etc complete all as specified and as directed. Note:- Cost of Glass panes /wire Cloth / lock /handle and other consumables required for the item shall be deemed to be included in the quoted rate.

S&F framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed.

S&F aluminum anodised grill DG-102 (10mmx5.2mm) of Decorative grill or equivalent fixed with 'F' Section size not less than 20.60x15.20x1.5mm thick of approved make complete all as specified and as directed. Note:- Minimum thickness of anodizing shall be 15 microns.

S&F steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with out glazing bars, dovetailed or welded complete all as specified and as directed.

S&F steel windows with top hung shutters including hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cu. M, getting out in soft/ loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50m & making good surface complete all as specified and as directed.

M&L for PCC (1:2:4) type B2 (using 40mm graded stone aggregates) as in posts and pillars complete all as specified and as directed.

M&L for cutting holes in brick walls, built in cement mortar or cement lime mortar, exc half brick but not exc one brick thick, for inserting hold fasts and making good dismantled portion in cement mortar (1:3) or cement concrete (1:2:4) type B1 complete all as specified and as directed.

S&F for clamps; hold fast; bands, straps, supports or stays for galvanised plain mild steel wire including bolts, rainwater, ventilating pipe and simillar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F for butt hinges, stainless steel, ISI Marked 100mm size, complete all as specified and as directed.

S&F MS butt hinges 100mm size, cold rolled, medium weight fixed with screws to wooden frames or welding to steel frames etc complete all as specified and as directed.

S&F aluminium anodized barrel tower bolts of extruded section length of bolt 150mm long complete all as specified and as directed.

S&F extruded aluminium alloy handles, fabricated type, anodised, 125 mm size complete all as specified and as directed.

S&F extruded aluminium alloy handles, fabricated type, 100 mm size complete all as specified and as directed.

S&F aluminium sliding door bolt, 250 mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections or cast alluminium alloy including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

S&F 12 mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice laminations, fixed with screws to aluminium frame work complete all as specified and as directed.

S&F 19mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws as in cup boards, shelves and pelmet boxes etc and including dismantling boarding any description fixed with screws complete all as specified and as directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apertupre 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F in repair 20mm dia aluminium Drapery rod, coated finish including teak wood brackets & end knob as required with teak wooden curtain rings complete all as specified and as directed.

Demolition of mud in roofs, any thickness, including plastering/ brick tiles or concrete and leeping (whether full thickness removed or only a part there of) with and including taking down existing tarfelt complete all as specified and as directed.

Demolition of reinforced concrete roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and as directed.

M&L for providing RCC nominal mix (1:2:4) tyype B1 (using 20mm aggregate stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide complete all as specified and as directed.

M&L for TMT or deformed bar 10mm dia and over, cut to length, bent to shape required includidng cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia.or securing with clips complete all as specified and as directed.

S&F mild steel TMT bars 8 to 10 mm dia as in stirrups, spacers and binders complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premices complete all as specified and as directed.

Demolition of stone slabs and tiles laid, beded and pointed in any mortar of any description or thicknes in floors , aprons etc complete all as specified and as directed.

M&L for joint free non skid coloured ceramic tiles, 7 to 8mm thick (squre or rectangular) area of each tile n.exc. 0.11sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, with and including over 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

M&L for joint free coloured glazed ceramic tiles in vertical surfaces of size (300x200)mm x 7mm thick/ (450x300)mm x7mm thick, set and jointed in cement slurry and pointed in white or coloured cement to match with and including 15mm thick cement rendering in cement mortar (1:4) complete all as specified and as directed.

M&L for joint free non skid coloured ceramic tiles, 7 to 8mm thick (squre or rectangular) area of each tile exc 0.18sqm but n.exc. 0.38sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, with and including over 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

Description all as per ser item No. 57.00 here in before but as in skirting / dado with and including over 10mm thick bedding layer in cement mortar (1:4) complete all as specified and as directed.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with and including over screed bed or bedding layer of mortar 15mm thick in cement mortar (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for vitrified tiles coloured, light shade 10 mm thick, area of each tile 0.36 Sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, with and including over 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

Description all as per ser item No. 60.00 above but as in skirting /dado laid over 10 mm thick bedding layer of CM (1:4) complete all as specified and as directed.

Demolition of brick work built in cement mortar, including all quoins, arches, pillars etc of any description including removing debrish from site complete all as specified and as directed.

M&L for brick work with sub class `B' bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed.

Supply only Integral Water Proofing compound complete all as specified all as directed.

Use and waste of form work to side of sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, and simillar work for rough finished surfaces of concrete complete all as specified and as directed.

M&L for RCC (Nominal Mix) (1:2:4) type B1 (using 20mm aggregate stone aggregates) as in beams, cantilevers, bressummers, lintels over 1.5m span concrete etc including necessary scaffolding complete all as specified and as directed.

M&L for PCC (1:2:4), type B-1 (using 20 mm graded stone aggregates) as in copings, bed plates, with and including necessary use and waste form work for kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

M&L for precast RCC (1:2:4) type B-1 (using 20mm graded stone aggregates) as in landing cover slab, drain cover, shelves troughs and the like including weathering slightly rounded or chamfered angles and throating fixed with CM (1:4) complete all as specified and as directed.

M&L for preparing plastered or unplastered new surfaces as on ceilings including brooming down or steel wire brushing, scraping down and applying three coats of white wash complete all as specified and as directed.

M&L for preparing old surfaces of ceilings including brooming down or steel wire brushing, scraping down and applying two coats of white wash complete all as specified and as directed.

M&L for preparing plastered or unplastered new surfaces on walls including brooming down or steel wire brushing, scraping down and applying two coats of distemper oil emulsion over one coat of alkali resistant primer complete all as specified and as directed.

M&L for complete removal of existing treatment of old plastered surfaces on walls including brooming down or steel wire brushing, scraping down and applying two coats of distemper oil emulsion over one coat of alkali resistent primer complete all as specified and as directed.

M&L for preparation of new plaster surface of walls, chajjas, soffits & beam including necessary scaffolding and applying two coats of cement base paint over one coat of chalk whiting primer complete all as specified and as directed.

M&L for complete removal of existing surface of walls, chhajjas, soffits & beam upto (G+3) storey including necessary scaffolding and applying two coats of cement base paint over one coat of chalk whiting complete all as specified and as directed.

M&L for preparation of new plastered surface of walls, chhajjas, soffits & beam upto (G+3) storey including necessary scaffolding and applying two coats of acrylic smooth exterior paint of required shade over a coat of exterior primer complete all as per manufacturer's instructions complete all as specified and as directed.

M&L for complete removal of existing surface of walls, chajjas, soffits & beam upto (G+3) storey including necessary scaffolding and applying two coats of acrylic smooth exterior paint of required shade over a coat of exterior primer complete all as per manufacturer's instructions complete all as specified and as directed.

M&L for preparation of new or previously untreated surfaces of wood of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of new or previously untreated surfaces of steel of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for preparation of old painted surfaces of wood and wood based material of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed

M&L for provision of 1 mm thick cement base wall care putty applying on walls for smooth finish complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C1 (using 20 mm graded stone aggregates) as in plinth protections, surface finished even and smooth without using extra cement complete including necessary use and waste of form work complete all as specified and as directed.

M&L for PCC (1:2:4), type B-0, (using 12.5 mm graded stone aggregate) as in roof padding 60mm average thickness to maintain slope etc complete all as specified and as directed.

M&L for preparation of plastered/concrete surfaces of roof and applying the under mentioned course of roof treatement complete all as specified and directed by Engineer-in-Charge.:- (a) Plastering 10mm thick in cement mortar (1:4) on concrete surfaces using WPC @3% by weight of cement, surface finished even and smooth (b) Surface shall be throughly wire brushed, cleaned, washed, dried up properly and apply evenly a bituminuous primer coat conforming to IS @0.4 ltr /Sqm over concrete / plastered roof surface. (c) Laying of 3mm thick APP membrane sheet (min weight 3 Kg/Sqm) consisting of a core of 160 gms/Sqm polyster non woven fabric mat protected on both sides with a high quality polymeric asphaltic mix again protected with thermo fusible HMHDPE FILM on dried primed surface by torch application method. APP membrane will normally be laid in length at right angle to the direction of slope. The over lap shall be minimum 100mm on longitudinal direction and 150mm on the transverse direction including cuttings, grooves etc. (d) Membrane bonded completely to the substrate & the over laps are then scaled/fused by flame.

M&L for cement concrete tiles (20cm x 20cm) x 20mm thick machine pressed, set & pointed in neat cement slurry in floor with grey cement and no pigment and cut and polished on roof over and including 15 mm thick screed bed in CM (1:4) complete all as specified and as directed.

Taking up or down 15mm steel tubing, bore of pipe in 15mm and connections in walls, ceiling, floors, etc including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20mm steel tubing, bore of pipe in 15mm and connections in walls, ceiling, floors, etc including cleaning for refixing or removal to store complete all as specified and as directed.

M&L for GI tubing, 15mm bore `medium grade` with all fittings and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed.

M&L for GI tubing, 20mm bore `medium grade` with all fittings and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed.

Dismantling water tanks exc 500 & n exc 1000 capacity in litres and removing to store complete all as specified and as directed.

S&F 1000 ltr rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified and as directed.

S&F ball brass valves, 20 mm bore, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F gun metal globe or gate valves, 20 mm bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

Taking down AC, PVC pipes of 100/110mm dia of any description including all fittings complete all as specified and as directed.

Taking down CI pipes of 100/110mm dia of any description including all fittings complete all as specified and as directed.

Taking down CI pipes of 75/80mm dia of any description including all fittings complete all as specified and as directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including suitable clamps at one meter of interval complete all as specified and as directed.

S&F for PVC (SWR) bends of radius, suitable for 110mm dia PVC pipes fixed complete all as specified and as directed.

S&F for 75mm bore cast iron waste and vent pipe in any length with or without ears fixed to walls including suitable clamps after every one mtr of interval with cement joints fixed to wall complete all as specified and as directed.

S&F 100mm bore cast iron waste and vent pipe in any length with or without ears fixed to walls with cement joints fixed to wall including suitable clamps after every one mtr of interval complete all as specified and as directed.

S&F CI 100mm bore bends complete all as specified and as directed.

S&F CI 100mm bore bends with door complete all as specified and as directed.

S&F for CI 100mm single branch piece with door complete all as specified and as directed.

S&F for CI 75mm bend with door complete all as specified and as directed.

S&F for cast iron cowls 100 mm size complete all as specified and as directed.

M&L in repairs for cast iron Nahani trap/floor trap with CP grating including jointing with cement joint to waste pipe of 75mm dia fixed in cement concrete type B-1(1:2:4) complete all as specified and as directed.

S&F in repairs for Cast Iron `P' Trap 100mm bore complete all as specified and as directed.

S&F in repairs vitreous china squatting pan, 'Orissa' pattern, size (580 x 440)mm white with integral foot rests, including connection to drain or outgoing pipe and to flushing pipe, antisyphonage pipe joint and to socket or stopper, including flush pipe all fittings etc complete all as specified and as directed.

S&F in repairs Vitreous china wash down water closet pan “Pedestal Pattern” coloured with WC seat cover coloured closed pattern with flat bottom and mild steel chromium plated or aluminium hinging device including PVC flush pipe and joints etc and connection to drain, flushing pipe, anti- syphonage pipe, and fixing arrangements with fixing bolts etc,complete all as specified and as directed.

S&F in repairs PVC low level flushing cistern 10 ltrs capacity, and connections to pipes and fixing of chain and pull, or lever, if any PVC valveless, syphonic action type, white, with inlet complete all as specified and as directed.

S&F in repairs vitreous china ware Wash Hand Basin, white, flat back of size (550 x 400) mm including MS brackets, cutting for and pinning in ends of brackets or erecting stand including brass CP union/waste fitting of 32mm dia and discharge pipe of 32mm dia PVC of 1.0 m length including one CP pillar tap 15mm size cast copper alloy with all fittings etc complete all as specified and as directed.

S&F Hand Shower (Health faucet) with 1.00 metre long Easy flex tube in chrome finish & wall Hook complete all as specified and as directed.Make:- Cat No ALD-CHR-565 of JAQUAR or equivalent of make MARC or KOHLER as approved by the GE.

S&F in repairs vitreous china urinals half stall type white or coloured with grating and union for discharge pipe etc complete all as specified and as directed.

S&F in repairs for PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

S&F MS steel work in tubular trusses and tubular posts including special shaped washers etc., complete using but welded tubes confirming to IS 1161- 1979 graded St 240 complete all as specified and as directed.

S&F pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to fixed the wall fixed with self taping scrows complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F in repairs stop valve (half turn)15 mm dia cast copper alloy, chromium plated, fancy type, high pressure, with crutch or butter fly handle, screwd for iron pipe or union and fixed complete all as specified and as directed.

S&F in repairs bib tap (half turn)15 mm dia cast copper alloy chromium plated, fancy type, with crutch or butter fly handle, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repair pillar tap (half turn) 15 mm dia, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure with or without lettered Hot or Cold with screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repairs brass chromium plated tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

surface dressing not exc 15cm deep soft/loose soil complete all as specified and as directed.

M&L for hard core of gauge n exc 63mm, deposited spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 75 mm thick cement concrete (1:4:8) type D2, (using 40 mm graded stone aggregate) as in sub base, surface finished even and fair complete including necessary use and waste of form work complete all as specified and as directed.

M & L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete laid over and including 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

M&L for Durastone heavy duty tiles of size (600x600)mm x10 mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match the colour of the tiles, over and including 15mm thick cement mortar screed bed in CM (1:6) complete all as specified and as directed.

Dismantling ceiling board, any size or description, fixed in any position or in any thickness, including cover fillets with nails complete as specified and as directed.

Providing & fixing false ceiling at all heights with semi perforated 12mm thick micro tegular edged GRG (Glass Fibre Reinforced Gypsum false ceiling tiles of size (595x595) mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRCO .50 TO 0.75 AS PER is 8225:1987, non combustible as per BS 476 (PART 4) -1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size (15x32)mm of length 3000mm, cross-T of size (15x32)mm of length 1200mm and secondary intermediate cross -T of size (15x32)mm of length 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e. 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size (85x25x2)mm, Galvanised iron perimeter wall angle of size (24x24x0.40)mm of length 3000mm to be fixed on periphery wall/partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall wood screws complete all as specified and as directed.

M&L for solid PVC wall lining consisting of 5mm thick supreme prelaminated colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications complete all as specified and as directed.

M&L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame complete all as specified and as directed.

Removing demolished materials etc (other than spoil) to a distance exc 1.00 KM and n exc 1.50 KM including loading, unloading and stacking etc. complete all as specified and as directed. Note:- The mode of measurement shall be as per SSR.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. any type all as specified and as directed.

Taking down ceiling fans of any sweep and any size including cable connections and disconnecting of fan blades and removing the fan with blades to store yard and hanging ceiling fan in its original position or any other position including as per direction of Engineer-in-Charge including its fitting and fixtures after carrying out the repairs i.e cleaning, rewiding, greasing and filling, replacement of bearings, painting of fan with one coat of synthetic enamel paint by spraying after preparation of surface by cleaning all dust and filling cavity with filler, reassembling the fan etc including testing complete all as specified and as directed by Engr-in-charge.

Taking down unservesiable sub main wiring with conduits/battens etc complete all as specified and as directed.

M & L for point wiring with single core PVC insulated but unsheathed 1.5 Sqmm FRLSH multistranded copper conductor cable 1100 volts grade IS-694 marked drawn in and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked with all conduit fittings and fixing accessories suitable for mounting modular switches including modular metal flush box and modular face plate with frame for mounting switches, sockets, fan regulators , etc and earth wire single core PVC insulated but unsheathed multistranded copper conductor cable 1100 volts grade IS-694 marked 1.5 Sqmm FRLS cable as continuous earth wire connecting to common earth dolly in concealed wiring system includes cutting of chases and making good disturbed surfaces complete all as specified and directed by Engr- in- Charge for the following :-(a) One light/fan point controlled by one switch one way

(b) One 3 pin 5 Amps socket out let point on the same board controlled by one switch complete

(c) One socket outlet 5 Amp controlled by one switch on independent board

Description all as per Srl item No 135.00 here-in-before but for one power point 6 pin 15 Amps socket out let with 2.5 Sq mm stranded copper conductor cable PVC insulated including earth wire 2.5 Sq mm copper conductor cable connected to earth dolly complete all as specified and as directed.

Description all as per Srl item No 135.00 here-in-before but for one 3 pin socket outlet 15 amps, independent, with cables 4 sqmm size complete all as specified and as directed.

S&F modular switch 1 way 6 Amps 1 module complete all as specified and as directed.

S&F modular switch 1 way 16 Amps 1 module complete all as specified and as directed.

S&F modular socket outlet 6A, 2/3 pin combined 2 module complete all as specified and as directed.

S&F modular socket outlet 6A/16A, 2/3 pin combined 2 module complete all as specified and as directed.

S&F ceiling rose, surface type, 65mm x 50mm, 2 to 3 terminal complete all as specified and as directed.

S&F step regulator, 120W - 2 module complete all as specified and as directed.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 250mm complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 Volt AC, recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F for sheet steel enclosures for MCB distribution board SPN 8 way 240Volt with 200 Amps bus bar, neutral link, earth bar din rail conforms IS-8822:96 and EIC 898-96, double door complete all as specified and as directed.

Supply and fixing for replacement Vertical type load line distribution board, double door, 4 way, AC, 3 Phase, 415 volts, TPN, bus bar 200 Amps rating and earth bus & din rail suitable for MCCB as incomer complete all as specified and as directed.

Supply and fixing MCCB 160 Amps 4 pole 36 kA 415 Volts 50 Hz with thermal adjustable magnetic settings, necessary conection including taking out old existing unserviceable MCCB from panels/VTPN etc complete all as specified and as directed.

Supply and fixing for MCB, SPN, 40-63A ,15kA complete all as specified and as directed.

Supply and fixing for MCB, SPN, 32A ,10kA complete all as specified and as directed.

Supply and fixing for MCB, SP, 5-32A,10kA complete all as specified and as directed.

Material and labour for submain wiring with two single core 4.00 sq mm PVC insulated FRLSH multistranded copper conductor cable drawing into and including rigid non metallic PVC conduit, medium grade ISI marked with all conduit fittings & fixing accessories and one single core 4.00 Sqmm multistranded copper conductor cable as continuous earth wire complete all as sepcified and as directed.

escription all as per srl item No. 156.00 above but for 6.00 sqmm wire complete all as specified and as directed. Note for srl item No. 156.00 & 157.00:- Two single core of mail cable, one single core of earth wire and PVC conduit shall be measured and paid as one run.

Supply and fixing LED light fitting 1x16 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and as directed.

S&F in replacement of LED street Light fittings 60 Watt 230V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, GI pipe light grade 40 mm dia bracket to make L type & MS flat clamp of size 30mm x 5mm thick including nuts, bolts and washer suitable for bldg light fitting with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection complete all as specified and as directed.

Supply and fixing in replacement of metal plug and socket with MCB and steel enclosure of capacity 20 Amp, SPN, MCB metallic complete all as specified and as directed.

Supply and fixing of new generation, post top lamp 20W IP65, energy saving environment friendly, long life aesthetically designed with symmetrical light distribution with high power LEDs as light source and connecting up with three core flexible copper conductor 1.5 sqmm cable with 40 mm dia GI pipe including PCC work complete all as specified and as directed.

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, check nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) with fair finish, internal surface of concrete chamber shall be given 15mm thick plaster in CM (1:4), funnel with wire gauge of 22 gauge, 8 mesh per liner inch, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) and specified including provision of earth wire protected by 15mm dia medium grade GI pipe and watering GI pipe shall be 20mm bore medium grade etc complete, all excavation and earth work & connecting the earthing to an earthing test point main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge.

Supply & laying in replacement of XLPE LT 1100 Volt grade, armoured under ground cable size of 35 Sqmm 4 core with stranded aluminium conductor in trenches /passing through pipes/ on poles etc with and including necessary excavation, earth work, sand cushioning, brick protection or pipe protection complele all as specified and as directed.

M/S Parshant Associates (BID ID -3085204)

JAIPAL AND BROTHERS (BID ID -3087431)

Shiv Shankar Nirman Co. (BID ID -3081502)

RK TRADERS (BID ID -3084803)

M/s Navansh Engineers & Consultants (BID ID -3075957)

HANUMAN BUILDERS (BID ID -3084719)

M/S Rohit Enterprises (BID ID -3086141)

Arihant Enterprises (BID ID -3087466)

SHEELSONS ENTERPRISES (BID ID -3086234)