Loading
Loading…
Loading…
| # | Company | Status |
|---|---|---|
| 1 | Admitted-Fee/PreQual/Technical | Admitted-Fee/PreQual/Technical |
| 2 | Admitted-Fee/PreQual/Technical 827 | RANCHI | JHARKHAND | 829205 | Admitted-Fee/PreQual/Technical |
| 3 | Admitted-Fee/PreQual/Technical | Admitted-Fee/PreQual/Technical |
Tender Value
₹13.9 L
EMD Value
₹28,000
Closing Date
17 Jul 2026, 5:00 pmClosed
EXECUTIVE ENGINEER
Drinking Water and Sanitation Division, Khunti
Khijur Toli SVS Group of Scheme Under Block- Torpa
2026_DWSD_116103_2
DWSD/KH-03(SVS)/2026-27 (1st Call)
Open Tender
Civil Works - Water Works
Turn-key
180 days
KHUNTI
Please refer Tender documents.
3 documents required · 3 mandatory
₹2,500
₹28,000
18 Jul 2026
11 Jul 2026
18 Jul 2026
11 Jul 2026
17 Jul 2026
11 Jul 2026
This is a percentage-rate BOQ. The schedule below shows estimated quantities and rates. Bidders quote a single percentage above or below the total estimated cost.
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1 | Tola: Khijur Toli, Village: Udikel, Block: Torpa (Khijur Toli Group of SVS) Model- 3 | - | - | - | - |
| 2 | Designing, Supplying, Installation, Testing & Commissioning with all tools & Parts of following Solar Photovoltaic (SPV) Solar Submersible D.C. Water Motor Pump Suitable for minimum 125mm x 115mm bore well as per MNRE Guideline with following specifications & accessories. | - | - | - | - |
| 3 | SPV arrays contains specified No of same capacity type & specification modules connected to series or parallel to obtained the required voltage & current the power output of individual PV modules should be minimum 200 watt peak. | - | - | - | - |
| 4 | i) The SPV modules should be as per IEC-61215 and IEC 61730 part 1.0) | - | - | - | - |
| 5 | ii) All external parts of motor pump used in submersible pump which are in contact of water is stainless steel grade 303 or higher as required. | - | - | - | - |
| 6 | iii) The PV modules should be mounted on metallic structure of adequate strength and appropriate design which can withstand load of modules & High wind pressure up to 200Km/h. | - | - | - | - |
| 7 | iv) The module mounting structure should be hot dip galvanized according to IS 4759. | - | - | - | - |
| 8 | v) To enhance the performance of SPV water pumping system & arrangement for seasonal tilt angle Adjustment should be provided | - | - | - | - |
| 9 | vi) Necessary arrangement should be provided in controller automatic start-run-stop through out the day with water level detection system. (As per MNRE Specification) | - | - | - | - |
| 10 | vii) Necessary protection such as lightening arrestor etc. should be provided to protect the controller & SPV | - | - | - | - |
stage.html
html • 0.02 MB
tech_bid_open.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.75 MB
term_cond.pdf
Tender Documents • 2.38 MB
BOQ_156956.xls
BOQ • 0.34 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .