SPECIAL REPAIR/IMPROVEMENT/CONVERSION OF LT OVERHEAD INTO UG CABLE AND ALLIED WORKS AT CERTAIN LOCATIONS AT AF STN ARJANGARH UNDER GE (AF) GURGAON

Amount

Dismantling of ACSR or AAC conductor

Dismantling cross arms of MS channel or angle sections etc complete and setting for reuse or tpt to store

Disamantling insulators any type any size

Dismatling earth wire or copper conductor , service feeder or distribution span

Fabricate, Supply, install, test and commissioning of CPRI tested Outdoor type LT panel board suitable for 440 Volt, 3 phase & Neutral , 50Hz supply , floor mounted weather and vermin proof fabricated from MS angle of size 50x50x5 mm as base frame,with 3.0 mm thick CRCA sheet and load bearing members such as door partitions etc of thickness not less than 2.0 mm thick , with gland paltes at bottom with suitable Brass chromium plated glands, with locking arrangements complete, duly powder coated with siemens grey colour after chemical treatment, including LED RYB indicators -06 nos on incoming side and ON/OFF/TRIP indications on outgoing side of breaker, interconnections from bus bars to MCCB's with suitable size aluminium bus bars, all internal ckt / protection wiring with FRHR 1100 V grade wiring with MCB protection,including terminal adapters, spreader links on incoming and out going sides of MCCB's complete all as specified and directed and comprising of the following :- (Panel No 01 Commercial )

(a) Bus bar Aluminium - 1200 A capacity- 04 Nos high conductivity, suitable for 415 V, 50 Hz supply including interconnection from incoming, and out going feeders with suitable mounting insulators, heat shrinkable colour sleeves.

(b) MCCB 4pole 630 Amps, 50 Hz, 415 V with rupturing capacity 50 KA, Adjustable Thermal Mangnetic range -01 Main incomer

(c) MCCB 315 Amps 3 pole 36 KA, with adjustable thermal magnetic range as out going- 01 No.

(d) MCCB 250 Amps 3 pole 36 KA with adjustable thermal magnetic range as out going- 01 Nos.

(e) MCCB 160 Amps 3 pole 36 KA with adjustable thermal magnetic range as out going- 04 Nos.

(f) MCCB 63 Amps 3 pole 16 KA with adjustable thermal magnetic range as out going- 03 Nos. (Spare)

(g) MCB TPN 63 Amps, 10 KA, 'C Series- 03 Nos

(h) MCB SPN 40 Amps, 10 KA, 'B' Series - 03 Nos

(i) Digital multifuctional meter (Make : L&T), 4410 Series, Cat No. WL441010OOOO- 01 Nos

(j) ON/OFF indication lamp with toggle switch and three Nos indication lamp (R,Y,B) - 10 Set of three

Fabricate, Supply install test and commissioning of CPRI approved Outdoor type LT panel board suitable for 440 Volt, 3 phase & Neutral , 50Hz supply , floor mounted weather and vermin proof fabricated from MS angle of size 50x50x5 mm as base frame,with 3.15 mm thick CRCA sheet and load bearing members such as door partitions etc of thickness not less than 2.0 mm thick , with gland plates at bottom with suitable Brass chromium plated glands, with locking arrangements complete, duly powder coated with siemens grey colour after chemical treatment, including LED RYB indicators -06 nos on incoming side and ON/OFF/TRIP indications on outgoing side of breaker, interconnections from bus bars to MCCB's with suitable size aluminium bus bars, all internal ckt / protection wiring with FRHR 1100 V grade wiring with MCB protection,including terminal adapters, spreader links on incoming and out going sides of MCCB's complete all as specified and directed and comprising the following :- ( DG Panel near to Gaurd room, commercial panel near to service center , security light panel naer to CSD canteen)

(a) Bus bar Aluminium - 500 A capacity- 04 Nos high conductivity, suitable for 415 V, 50 Hz supply including interconnection from incoming, and out going feeders with suitable mounting insulators, heat shrinkable colour sleeves.

(b) MCCB 160 Amps 4 pole 36 KA, with adjustable thermal magnetic range as out going- 01 No.(Main incomer)

(c) MCCB 63 Amps 4 pole 16 KA with adjustable thermal magnetic range as out going- 04 Nos.

(d) MCB TPN 63 Amps, 10 KA, 'C Series- 03 Nos

(e) MCB SPN 40 Amps, 10 KA, 'B' Series - 04 Nos

(f) Digital multifuctional meter (Make : L&T), 4410 Series, Cat No. WL441010OOOO- 01 Nos

(g) ON/OFF indication lamp with toggle switch and three Nos indication lamp (R,Y,B) - 7 Set of three

Fabricate, Supply install test and commissioning of CPRI tested Outdoor type LT panel board suitable for 440 Volt, 3 phase & Neutral , 50Hz supply , floor mounted weather and vermin proof fabricated from MS angle of size 50x50x5 mm as base frame,with 3.15 mm thick CRCA sheet and load bearing members such as door partitions etc of thickness not less than 2.0 mm thick , with gland plates at bottom with suitable Brass chromium plated glands, with locking arrangements complete, duly powder coated with siemens grey colour after chemical treatment, including LED RYB indicators -06 nos on incoming side and ON/OFF/TRIP indications on outgoing side of breaker, interconnections from bus bars to MCCB's with suitable size aluminium bus bars, all internal ckt / protection wiring with FRHR 1100 V grade wiring with MCB protection,including terminal adapters, spreader links on incoming and out going sides of MCCB's complete all as specified and directed and comprising the following :- (Panel No 04 Commercial SNC mess new /old)

(a) Bus bar Aluminium - 500 A capacity- 04 Nos high conductivity, suitable for 415 V, 50 Hz supply including interconnection from incoming, and out going feeders with suitable mounting insulators, heat shrinkable colour sleeves.

(b) MCCB 315 Amps 4 pole 36 KA, with adjustable thermal magnetic range Main incomerg- 01 No.

(c) MCCB 160 Amps 3 pole 36 KA with adjustable thermal magnetic range as out going- 03 Nos.

(d) MCCB 100 Amps 3 pole 25 KA with adjustable thermal magnetic range as out going- 03 Nos. (Spare)

(e) MCB TPN 63 Amps, 10 KA, 'C Series- 03 Nos

(f) MCB SPN 40 Amps, 10 KA, 'B' Series - 04 Nos

(g) Digital multifuctional meter (Make : L&T), 4410 Series, Cat No. WL441010OOOO- 01 Nos

(h) ON/OFF indication lamp with toggle switch and three Nos indication lamp (R,Y,B) - 10 Set of three

Fabricate, Supply install test and commissioning of CPRI tested Outdoor type LT panel board suitable for 440 Volt, 3 phase & Neutral , 50Hz supply , floor mounted weather and vermin proof fabricated from MS angle of size 50x50x5 mm as base frame,with 3.15 mm thick CRCA sheet and load bearing members such as door partitions etc of thickness not less than 2.0 mm thick , with gland plates at bottom with suitable Brass chromium plated glands, with locking arrangements complete, duly powder coated with siemens grey colour after chemical treatment, including LED RYB indicators -06 nos on incoming side and ON/OFF/TRIP indications on outgoing side of breaker, interconnections from bus bars to MCCB's with suitable size aluminium bus bars, all internal ckt / protection wiring with FRHR 1100 V grade wiring with MCB protection,including terminal adapters, spreader links on incoming and out going sides of MCCB's complete all as specified and directed and comprising the following :- (Panel No 17 Distribution Panel SNCO mess new /old)

(a) Bus bar Aluminium - 500 A capacity- 04 Nos high conductivity, suitable for 415 V, 50 Hz supply including interconnection from incoming, and out going feeders with suitable mounting insulators, heat shrinkable colour sleeves.

(b) MCCB 160 Amps 4 pole 36 KA with adjustable thermal magnetic range as out going-Main incomer 01 Nos.

(c) MCCB 100 Amps 3 pole 25 KA with adjustable thermal magnetic range as out going- 02 Nos. (Spare)

(d) MCCB 63 Amps 3 pole 16 KA with adjustable thermal magnetic range as out going- 03 Nos. (Spare)

(e) MCB TPN 63 Amps, 10 KA, 'C Series- 03 Nos

(f) MCB SPN 40 Amps, 10 KA, 'B' Series - 04 Nos

(g) Digital multifuctional meter (Make : L&T), 4410 Series, Cat No. WL441010OOOO- 01 Nos

(h) ON/OFF indication lamp with toggle switch and three Nos indication lamp (R,Y,B) - 10 Set of three

Fabricate, Supply install test and commissioning of CPRI tested Outdoor type LT panel board suitable for 440 Volt, 3 phase & Neutral , 50Hz supply , floor mounted weather and vermin proof fabricated from MS angle of size 50x50x5 mm as base frame,with 3.15 mm thick CRCA sheet and load bearing members such as door partitions etc of thickness not less than 2.0 mm thick , with gland paltes at bottom with suitable Brass chromium plated glands, with locking arrangements complete, duly powder coated with siemens grey colour after chemical treatment, including LED RYB indicators -06 nos on incoming side and ON/OFF/TRIP indications on outgoing side of breaker, interconnections from bus bars to MCCB's with suitable size aluminium bus bars, all internal ckt / protection wiring with FRHR 1100 V grade wiring with MCB protection,including terminal adapters, spreader links on incoming and out going sides of MCCB's complete all as specified and directed and comprising the following :- (Panel No 06 MT/Pump house No 07 , STP)

(a) Bus bar Aluminium - 500 A capacity- 04 Nos high conductivity, suitable for 415 V, 50 Hz supply including interconnection from incoming, and out going feeders with suitable mounting insulators, heat shrinkable colour sleeves.

(b) MCCB 315 Amps 4 pole 36 KA, with adjustable thermal magnetic range as out going- Main incomer 01 No.

(c) MCCB 160 Amps 3 pole 36 KA with adjustable thermal magnetic range as out going- 03 Nos.

(d) MCCB 100 Amps 3 pole 25 KA with adjustable thermal magnetic range as out going- 02 Nos. (Spare)

(e) MCB TPN 63 Amps, 10 KA, 'C Series- 03 Nos

(f) MCB SPN 40 Amps, 10 KA, 'B' Series - 04 Nos

(g) Digital multifuctional meter (Make : L&T), 4410 Series, Cat No. WL441010OOOO- 01 Nos

(h) ON/OFF indication lamp with toggle switch and three Nos indication lamp (R,Y,B) - 10 Set of three

Fabricate, Supply install test and commissioning of CPRI tested Outdoor type LT panel board suitable for 440 Volt, 3 phase & Neutral , 50Hz supply , floor mounted weather and vermin proof fabricated from MS angle of size 50x50x5 mm as base frame,with 3.15 mm thick CRCA sheet and load bearing members such as door partitions etc of thickness not less than 2.0 mm thick , with gland plates at bottom with suitable Brass chromium plated glands, with locking arrangements complete, duly powder coated with siemens grey colour after chemical treatment, including LED RYB indicators -06 nos on incoming side and ON/OFF/TRIP indications on outgoing side of breaker, interconnections from bus bars to MCCB's with suitable size aluminium bus bars, all internal ckt / protection wiring with FRHR 1100 V grade wiring with MCB protection,including terminal adapters, spreader links on incoming and out going sides of MCCB's complete all as specified and directed and comprising the following :- (Panel No 09 Distribution Panel Air fource Schoole, Acct, SMC)

(a) Bus bar Aluminium - 500 A capacity- 04 Nos high conductivity, suitable for 415 V, 50 Hz supply including interconnection from incoming, and out going feeders with suitable mounting insulators, heat shrinkable colour sleeves.

(b) MCCB 250 Amps 4 pole 36 KA with adjustable thermal magnetic range Main incomer- 01 Nos.

(c) MCCB 160 Amps 4 pole 36 KA with adjustable thermal magnetic range as out going- 02 Nos.

(d) MCCB 100 Amps 3 pole 25 KA with adjustable thermal magnetic range as out going- 02 Nos. (Spare)

(e) MCCB 63 Amps 3 pole 16 KA with adjustable thermal magnetic range as out going- 03 Nos. (Spare)

(f) MCB TPN 63 Amps, 10 KA, 'C Series- 03 Nos

(g) MCB SPN 40 Amps, 10 KA, 'B' Series - 04 Nos

(h) Digital multifuctional meter (Make : L&T), 4410 Series, Cat No. WL441010OOOO- 01 Nos

(i) ON/OFF indication lamp with toggle switch and three Nos indication lamp (R,Y,B) - 10 Set of three

Fabricate, Supply install test and commissioning of CPRI tested Outdoor type LT panel board suitable for 440 Volt, 3 phase & Neutral , 50Hz supply , floor mounted weather and vermin proof fabricated from MS angle of size 50x50x5 mm as base frame,with 3.15 mm thick CRCA sheet and load bearing members such as door partitions etc of thickness not less than 2.0 mm thick , with gland plates at bottom with suitable Brass chromium plated glands, with locking arrangements complete, duly powder coated with siemens grey colour after chemical treatment, including LED RYB indicators -06 nos on incoming side and ON/OFF/TRIP indications on outgoing side of breaker, interconnections from bus bars to MCCB's with suitable size aluminium bus bars, all internal ckt / protection wiring with FRHR 1100 V grade wiring with MCB protection,including terminal adapters, spreader links on incoming and out going sides of MCCB's complete all as specified and directed and comprising the following :- (Panel No 10 Distribution A/M billet, DSC billet,Mess, Armoury )

(a) Bus bar Aluminium - 500 A capacity- 04 Nos high conductivity, suitable for 415 V, 50 Hz supply including interconnection from incoming, and out going feeders with suitable mounting insulators, heat shrinkable colour sleeves.

(b) MCCB 315 Amps 4 pole 36 KA, with adjustable thermal magnetic range Main incomer- 01 No.

(c) MCCB 250 Amps 4 pole 36 KA with adjustable thermal magnetic range as out going- 01 Nos.

(d) MCCB 160 Amps 4 pole 36 KA with adjustable thermal magnetic range as out going- 01 Nos.

(e) MCCB 100 Amps 3 pole 25 KA with adjustable thermal magnetic range as out going- 04 Nos.

(f) MCB TPN 63 Amps, 10 KA, 'C Series- 03 Nos

(g) MCB SPN 40 Amps, 10 KA, 'B' Series - 04 Nos

(h) Digital multifuctional meter (Make : L&T), 4410 Series, Cat No. WL441010OOOO- 01 Nos

(i) ON/OFF indication lamp with toggle switch and three Nos indication lamp (R,Y,B) - 10 Set of three

Fabricate, Supply install test and commissioning in repair of Feeder pillar box (Out door type) of size cm x 60 cm x 50 cm x 40 cm (H x W x D) suitable for 440 Volt, 3 phase & Neutral , 50Hz supply, floor mounted weather and vermin proof fabricated from MS angle of size 50x50x5 mm as base frame,with 2.5 mm thick CRCA sheet with gland plates at bottom with suitable Brass chromium plated glands, with locking arrangements complete, duly powder coated with siemens grey colour after chemical treatment, including with suitable size aluminium bus bars 250 Amps 04 Nos in its full width (60 cm length) to be fixed on suitable size of insulators. The bus bar having 08 Nos of holes including provision of suitable size of nuts and bolts of all four bus bars, the feeder pillar box shall be floor mouted with provision of four nos of legs made out out 50 x 50 x 5 mm MS angle not less than 40 cm and provision of 01 No. MCCB 160 Amps, 4 Pole, 25 KA, Fixed thermal and magnetic relase type, the panel shall be grouted under PCC 1:2:4 complete all as specified and directed. F P No 7,8,12,13,14,16,15,

Fabricate, Supply install test and commissioning in repair of Feeder pillar box (Out door type) of size 100 cm x 80 cm x 40 cm (H x W x D) suitable for 440 Volt, 3 phase & Neutral , 50Hz supply, floor mounted weather and vermin proof fabricated from MS angle of size 50x50x5 mm as base frame,with 2.5 mm thick CRCA sheet with gland plates at bottom with suitable Brass chromium plated glands, with locking arrangements complete, duly powder coated with siemens grey colour after chemical treatment, including with suitable size aluminium bus bars 600 Amps 04 Nos in its full width (60 cm length) to be fixed on suitable size of insulators. The bus bar having 08 Nos of holes including provision of suitable size of nuts and bolts of all four bus bars, the feeder pillar box shall be floor mouted with provision of four nos of legs made out out 50 x 50 x 5 mm MS angle not less than 40 cm the panel shall be grouted under PCC 1:2:4 complete all as specified and directed. FP No 17

Supply , laying , jointing & testing and lay XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 3.5 core 300 sq mm.

Supply , laying , jointing & testing XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 3.5 core 240 sq mm.

Supply , laying , jointing & testing XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 3.5 core 185 sq mm.

Supply , laying , jointing & testing XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 3.5 core 120 sq mm.

Supply , laying , jointing & testing XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 3.5 core 95 sq mm.

Supply , laying , jointing & testing XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 3.5 core 50 sq mm.

Supply , laying , jointing & testing XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 4 core 16 sq mm (FOR SECURITY LIGHTS)

Supply , laying , jointing & testing XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 4 core 25 sq mm Note for item No. 14 to 21 The rate quoted by the contractor deemed to be inclusive of suitable size aluminium lugs at any required length at both ends of cable. 2. Suitable size of cable chromium plated stainless steel glands etc.

Supply and fixing TPN DB's 4 way vertical type 415 V, double door suitable for housing of 100 Amps MCCB as main incoming including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

Supply and fixing MCCB 63 Amps, 3 Pole, 16 KA, fixed type, suitable to be fixed in 4 way TPN DB complete all as specified and directed.

Suply and fixing 240 V, 10 KA, 'B' curve miniature circuit breaker (MCB) of single pole and current carrying capacity SP 40 Amps in the MCB DB complete with connection testing and commissioning.

S & F sub main wiring for circuit of size 10 sq mm 2 core (FRLS) alongwith earth wire of 25 sq mm single core of FRLS PVC insulated unsheathed cable, 1100 volts grade with multistranded copper conductor including PVC conduit of suitable size complete all as specified and directed by Engr-in-Charge. (FOR SPN DB's)

M & L Earthing complete for sub station equipments with galvanized steel earth plate electrod of size 600x600x6.3mm thick burried directly in the ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below the ground level, connected to galvanised iron strip 25 x 4 mm by means of nuts, bolts,check nuts and washers of galvanised or steel all as specified or shown in electrical plate No. 3 of SSR-2009( Part-l), including earth work and excavation in any strata, GI pipe 40mm dia light grade for protection of galvanised iron earthing strip upto 7.5 mtrs, including concrete chamber of PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) having copping in PCC (1:3:6) Type C-1using 20mm graded stonr aggregate. Intemal surface of concrete chamber shall be plastered with 12mm thick cement mortar (1;4) and 50mm thick RCC cover in proportion (1:2:4) type B-1using 20mm graded stone aggregate, reinforced with 8mm dia tor bar@ 80mm c/c both ways and charcoale dust common salt etc.,funnel testing point, 8 mesh per liner inch, including test point , testing, complete .

M & L Earthing complete for sub station equipments with galvanized steel earth plate electrod of size 600x600x6.3mm thick burried directly in the ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below the ground level, connected to galvanised or steel conductor of size 4 mm by means of nuts, bolts,check nuts and washers of galvanised or steel all as specified or shown in electrical plate No. 3 of SSR-2009( Part-l), including ncessary earth work and excavation in any strata, GI pipe 40mm dia light grade for protection of galvanised iron earthing strip upto 7.5 mtrs, including concrete chamber of PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) having copping in PCC (1:3:6) Type C-1using 20mm graded stonr aggregate. Intemal surface of concrete chamber shall be plastered with 12mm thick cement mortar (1;4) and 50mm thick RCC cover in proportion (1:2:4) type B-1using 20mm graded stone aggregate, reinforced with 8mm dia tor bar@ 80mm c/c both ways and charcoale dust common salt etc.,funnel testing point, 8 mesh per liner inch, including test point , testing, complete .

S & F pole box for street light dust and vermin proof with hinged door and locking arrangement make Sintex model GSJB 3020 complete with 4 way connector 2 Nos. of capacity 60 amps incl one MCB SP C series 06 amps 10 KA capacity for Security light connection with flexIble wire 3 core 2.5 sqmm with suitable size of PVC conduit and including suitable clamps & suitable size brass chrome plated glands-02 nos at bottom for cable entry and exit complete all as specified and as directed. Make shall be : Sintex/National/BCH.

Supply and fixing steel tubular pole, swaged, complete with cast iron base plate, finial taper plug, bolts, nuts, washer and screws including painting with two coats of aluminium paint over one coat of red oxide primer on all exposed surfaces and tarring with black bituminous paints to portion embedded in PCC including numbering of poles with two coats of synthetic enamel paints, type 410-SP-31 (9 meter long) including street light brackets made out of GI tubing light grade, 40 mm bore 1200 mm long bent to sahpe at 120 degree, fixed on pole by providing MS clamp made up to flat iron 50 x 6 mm including nuts and washer of suitable size, fixed in repairs complete, Including disconnecting and taking out old damage PCC pole all as directed .

Supply and fixing in repair LED street light fittings 70 watts 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including therma; management in multiple optics complete with IP 65/66 protection complete with provision of twin core copper wire 23/0.0076 upto security light from pole loop box . Cat No. ENDURACITYLINERNEOSL70WLED757PASYBOTG Make : Havells or equivalent in Bajaj/Wipro/Crompton

M & L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate in foundations, filling and mass complete.

M & L for Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete.

M & L for cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in copings to poles & the like, etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete.

M&L Cross-arms, Bracings, Supports, Clamps and Back Plates fabricated from Structural Steel Sections including Nuts, Bolts, Washer, welding, bending cold or hot, drilling holes for Bolts, in any shape or size as indicated/ directed and inclusive of one coat of Aluminium Primer one Under Coat and One Finishing Coat of Aluminium Paint, complete all as specified and as directed. (for loop boxes and fixing of GI pipe with pole)

Excavating in trenches, in any type of soil not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc and getting out in any type of soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, leveling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed..

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supply laying and jointing GI pipe 'light grade' 50 mm bore in trenches/under floors or roads/ along poles/ on wall incl clamps for protection of cables incl fittings complete all as specified and directed.

Supply laying and jointing GI pipe 'light grade' 100 mm bore in trenches/under floors or roads/ along poles/ on wall incl clamps for protection of cables incl fittings complete all as specified and directed.

M & L for clean and dry sand (un washed) in trenches incl spreading and levelling for cushioning of UG cable complete all specified and directed.(Note: Punned thickness shall be measured)

M & L for brick size sub class ‘B’ (modular size), laid flat in trenches for protection of cable complete all as specified and directed.

ARE ESS ENGINEERING SERVICES (BID ID -3366593)

AS Engineering (BID ID -3374360)

Ish Engineers and Contractors (BID ID -3366669)

D P ENTERPRISES (BID ID -3366008)