Mulanur Block ITPHDS 2025 26 Costructio of Community Hall at Ponnivadi AD Colony

Amount

1.Construction of Community Hall in Ponnivadi Adi Dravidar colony at Ponnivadi Panchayat

Earth work excavation and depositing on banks with initial lead and lift in gravelly soil stiff clay, hard stiff clay, murram, boulders mixed with gravel as per SS 20-B for foundation.

Filling M. Sand including cost and conveyance loading unloading from approved quarry to work site and labour charges for filling, ramming, etc. Complete

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,

Cement concrete 1:4:8 mix using 40mm ISS HBG metal including all cost and conveyance, labour charges etc. Complete.

Brick work in CM 1:5 mix using country Bricks including cost and conveyance labour charges etc. Complete.

Upto Basement

Super Structure

Supply and errecting sheet centering of size 90 cm x 60cm 10 G sheet laid over silver oak joist and supported by casurina post of size 10 cm x 13 cm dia spaced at 75 cm center to center etc. complete

Upto Basement

Above Basement

Supply and fabrication of steel for RCC works including cost and conveyance charges etc

RCC 1 :1.5 : 3 mix using 20mm ISS HBG metal including cost and conveyance of all materials but excluding centering charges including labour charges for mixing laying concrete etc., complete

Upto Basements

Above Basement

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone M.Sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the Top of Roof with one course of Pressed Tiles of size 20 cm x 20 cm x 2 cm laid in cement mortor 1 : 3 and pointing with the same mortor mixed with water proof compound including cost and conveyance off all materials and labour charges etc complete

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The Surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers. [The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (waterproof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coat of putty, scrapping the putty area to level the surface smooth, etc., complete). The Putty should be got approved by the Executive Engineer

Plastering in CM 1:5, 12mm thick including cost and conveyance charges etc.,

Plastering in CM 1:4 20mm thick including cost and conveyance of all materials and labour charges etc. complete

Plain Cement Concrete 1:2:4 mix using 20mm ISS HBG metal including cost and conveyance of all materials and labour charges etc. complete

Paving the floor with scrach proof ceramic tiles of any colour and any size laid in CM 1:2, 20 mm thickand pointing with white cement using 0.4kg/Sq m mixed with colouring pigments to suit colour of the tiles including finishing tec., complete

Paving the floor with Antiskid tiles of any colour and any size laid in CM 1:3, 20 mm thickand pointing with white cement using 0.4kg/Sq m mixed with colouring pigments to suit colour of the tiles including finishing tec., complete

Dadooring walls with glazed tiles of size 0.15 x 0.15 set with CM 1:2, 10 mm thick etc., complete

Supply of the following steel doors, windows and ventilators to Office, etc. complete

Main Door - D 1.80x2.10m

Door - D1 0.90x2.10m

Door - D2 pvc door 0.75x2.10m

Window - W 1.50x1.30m

Window - W1 0.90x1.30m

Ventilator 0.90x0.45m

Ventilator 0.60x0.45m

Supply of the following PVC pipes and PVC specials etc. complete For Seewage Line and Rainwater Down Fall Pipe with necessary bend ,shoes and clamp and labour charges etc complete

110mm PVC pipe

Supply of Manhole cover 60cm x 60 cm 2 Nos.

Painting Two Coats of OIL Bound Distember of approved colour over one Primer Coat including cost of Paint and labour charges etc complete

Painting Two Coats with exterior emulsion of approved colour over one Primer coat including cost of Paint and labour charges etc complete

Painting two coats with ready mixed paint including cost and conveyance charges etc.

Supply and Fixing of Cudapah Slab of 25mm/40mm thick including cost and conveyance of all materials and labour charges etc complete

Supplying & Fixing in position of Indian type Water closet 580x440mm of approved quality

Supplying & Fixing in position of EWC of approved quality

Wiring with 2 x 1.50 sqm ( 22/0.3 ) PVC insulated unsheathed single core Copper Conductor of 1100 v Grade in suitable PVC Rigid Pipe on wall and ceiling with PVC accesseries with TW box 150 mm x 100 mm x 113 mm for 5 A 3 Pin non inter locking cs plug with painting of suitable colour with contionues earth wire connection of 14 SWG TC Wire for PVC PLUG Point S D No 36

Wiring with 2 x 1.50 sqm ( 22/0.3 ) PVC insulated unsheathed single core Copper Conductor of 1100 v Grade in suitable PVC Rigid Pipe on wall and ceiling with PVC accesseries with TW Switch box with 5 A F . T . Switch with painting of suitable colour for OPEN PVC Light Point and Fan Point ( For Eloctronic Regulator ) SD No 25

Supply and fixing of WT bulk head fitting with guard suitable for 15 W LED Bulb SD 83

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1" x 1/8" copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connection ( SD No 126 )

Supply and Run of 2 of 6 sqmm ( 84 / 0.3 ) PVC insulated single core unsheathed Copper Conductor of 1100 v Grade on 7 / 20 G I Bearer wire for Service Connection Mains ( SD No 66 )

Supply and Run of 2 of 6 sqmm ( 84 / 0.3 ) PVC insulated single core unsheathed Copper Conductor of 1100 v Grade in 25 mm dia G I suitable pipe b class suitably bended both ends with necessery angle iron upright and end support For Mains ( SD No 71 )

Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb S D No 84

Supply and fixing of 1200 mm ( 48" ) A C Ceiling Fan complete with stepped eloctronic 300 w regulator with 1.00 meter down Rod on the existing clamp SD No 110

Provision for Metre Board

Provision for EB Deposit charges

Supply and delivery and fixing of HDPE tank including laoading and unloading transportion and labour charges for fixing of GI pipes and special for pipe connection work inluding cutting, threading and fixing charges etc.,

1000litres

Provision for sanitary arrangements

Supply and delivery of 110 mm dia PVC Pipe 4 kg

Supply and delivery of Following specials

110 mm dia Elbow

110 mm dia Tee

Provision for water supply arrangements

Supply and delivery of 63 mm dia PVC Pipe 4 kg

Earth Work excavation and deposting on bank

Laying and Jointing PVC pipe with Specials

Refilling the excavated excess earth

Supply and delivery of Following specials

63 mm dia Elbow

25 mm dia Elbow

63mm dia Tee

25mm dia coupler

PVC Screw Down Tap Heavy Type 20mm dia

Provision for Ramp & Stair case hand rail

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floorpolishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

Provision for Lock and Key

Provision for name board

Photocharges

GST Amount for providing Service to Government Contract Works for the above Construction & Maintenance Works. { GST Amount is the Total GST Amount for overall quoted amount (Both Construction and Maintenance) above this row in column "BB" for all works in this package} (Refer Clause 13.2 & 13.3 of Section 2 of Instruction to Bidders (ITB) of SBD)

N.Kuppusamy (BID ID -1396505)