SPECIAL REPAIR TO EXISTING TEMPORARY BUILDING BY REPLACING AC SHEET WITH GALVANIZED SHEET AND FALSE CEILING (PHASE-III), T-19(LIVING IN ACCN FOR SNCOs) AND PROVN OF MISCELLANEOUS B/R WORKS SERVICES AT P-145(12 ASC) AT AFS BEGUMPET UNDER GE (AF) HKPT

Amount

Notes:- In case description of any two or more items of the BOQ is same and the tenderer quotes different rates for such items, only lowest rate of such items will be considered for acceptance and subsequently payment will be made upon execution of the items accordingly.

Dismantling AC corrugated, semi corrugated sheets in roof covering complete all as specified and directed.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding and Ridge to wall, fixed with self tapping screws as specified.

Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161- 1979 grade St.-240

S&F Rolled sections as in main and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates (Fe 410-W Gde-E-250 quality-A).

M&L Preparing new steel Surfaces of any any description over 10cm width or girth and appling two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete.

Dismantling ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets.

S&F 600x600mm GI bottom pre coated exposed snap grid frame work with 25x25x7mm wall angle and 25mm web, 35mm flange 0.7mm thick T-sections hanging with 4mm dia GI wire (up to 1200 mm long) including level clip, soffit cleat and 12.7 mm dia metal Raw plug at 1200mm c/c in both direction complete all as specified and directed

S&F PVC laminated designed (one side PVC lamination and other side aluminium paper) gypsum board 600 X 600 X 8 mm thick tiles decorative type in GI grid frame work with screws or clips etc complete all as specified and as directed by Engineer-in-Charge.

Demolition of brick work or stone/ boulder or block masonry, built in cement mortar or cement lime mortar including all quoins, pillars etc.

M&L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and as directed by Engineer-in-charge.

Taking down cement or cement lime plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed by Engineer-in-charge.

M & L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 , finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

M& L for PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in copings complete all as specified and as directed by Engineer-in-charge.

M&L for Preparing new plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali reistance primer complete all as specified and directed.

M&L for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts

Dismantling timber scantling 40 Sqcm and over in section incl trusses in any position as in unframed work, complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with creosote.

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness.

M & L 25 mm thick PCC 1:2:4 type B1 (Using 20 mm graded granite stone aggregate) in sub base of floorings complete all as specified and as directed by Engineer-in-charge.

M & L for Screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar 1:6 complete all as specified and as directed by Engineer-in-charge.

M&L for Vitrified light coloured Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc set & jointed in neat cement slurry & pointed in white or coloured cement to match complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 21 above but on verticle surfaces.

S&F Non Skid colored ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match.

All as per Item No. 23 above but in skirting/ dado.

M&L for complete removal of existing treatment (upto plaster surface) of old painted surfaces including 3mm thick wall care putty and applying two coats of distemper oil emulsion on surfaces of walls complete all as specified and as directed by Engineer-in-charge.

M&L for complete removal of existing treatment (upto plaster surface) of old painted surfaces and applying two coats of cement base paint on surfaces of walls complete all as specified and as directed by Engineer-in-charge.

Demolition of cement concrete (unreinforced and including tiles) in ground floors and pavings n exc 15 cm thickness (below or above ground level) all as specified and directed by Engineer-in-charge.

M&L for 75mm Cement concrete Type C-2 1:3:6 (40mm graded aggregate) for plinth protection complete all as specified and directed.

M&L Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface.

M&L for Chequered cement concrete tiles 20cm x 20cm x25mm thick with grey cement and pigment, machine pressed, set jointed and pointed in neat cement slurry in floors over 15mm thick cement screed bed in cement and sand mortar 1:6 complete all as specified.

M&L for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc.complete .

M&L for along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement:2 coarse sand) to match the existing floors complete all as specified and as directed by Engineer-in-charge.

M&L for voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and as directed by Engineer-in-charge.

M&L for wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed by Engineer-in-charge.

S & F Second class hard wood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exceeding 13 and not exceeding 25 Sq. cm complete all as specified and as directed by Engineer-in-charge.

S&F of 18mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on only one face; fixed with screws complete all as specified and as directed by Engineer-in-charge.

Extra over rates of block board or veneered particle board or plywood for external teak wood lipping, 6mm thick fixed with nails 18 mm thick all as specified and directed

M&L for 0.9 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions

S&F of 75 mm Brass barrel tower bolts with cast or sheet barrel and rolled or cast bolts and fixed

S&F of 100 mm long chromium plated brass handles fancy type all as specified and directed

S&F of Cup board lock brass 4 levers all as specified and directed

S&F of Stainless steel auto closing cup-board hinges

M & Labour for 25mm dia Stainless Steel Curtain Rod fancy type complete all as specified and directed

M & Labour in repair for Brackets, Ends Cap and Holder suitable for 25mm dia Stainless Steel Curtain Rod fancy type complete all as specified and Approved.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises outside low laying area all as specified and directed by Engineer-in-Charge.

M&L non skid ceramic joint free coloured tiles 7 to 8mm thick (Square/ Rectangular) design area exceeding 0.06 sqm but not exceeding 0.11 sqm in floors set and jointed in neat cement slurry over and including 15mm thick screed bed in CM (1:4) jointed in neat cement slurry and pointed in coloured cement complete all as specified and directed by Engineer-in-Charge.

M&L glazed ceramic 350 x 250x 7mm/ 450mm x 350mm x 7mm tiles (coloured) on vertical surfaces set and jointed in neat cement slurry and including 10mm thick plaster in CM (1:3) and pointed in white or colour cement to match all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections 15mm bore of pipe, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down steel tubing and connections 20mm bore of pipe, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge.

Supplying and laying 16mm of CPVC pipes SDR11 & Plain CPVC SDR 11 fitting on walls/ceiling or laying in floors complete all as specified

All same as per item here-in-before but 20 mm bore.

Reinforced Cement Concrete Type B1 1:2:4 (using 20 mm graded granite stone aggregate) in Beams, cantilevers, lintels over 1.5 M span.

M&L for Fair finished flat form work to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports etc.

Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips

Mild steel TMT bars 5 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips.

Supply and fix vitreous china ware wash hand basin 470 x 470 x 110mm size Table Top Basin Make JAGUAR Cat No FSS-WHT-29901 or equivalent in Hindware/Cera

S&F for Vitreous China urinals, half stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating, Union and all fitting for discharge pipe.

S&F 32mm Dia PVC waste pipe for sinks or wash basines etc,. in repairs complete all as specified and as directed by the Engr-in-Charge.

Supply and fix 32 mm dia bore waste fittings brass chromium plated fixed to wash hand basin/urinals with long screwed shanks and fly nuts flange and bedded in run lead cement and other end fixed in repairs complete all as directed by the Engr-in-Charge.

S&F Bib taps, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule 15mm dia and fixed

S&F angle valves, cast copper alloy, chromium plated crewed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair.(15mm bore).

Supply and fix 15 mm bore LDPE pipe 45cm long with brass nuts and washers on both ends all as in repairs specified and directed.

M&L for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement

Supply and fix Single Lever mini Basin mixer without Popup waste system with 450mm long Braided Hoses Make JAGUAR Cat No FLR-5025B or equivalent in Hindware/Cera

S&F in repairs vitreous china wash down water closet pedestral pan white/ coloured, including, plastic water closet seat, closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hanging device, complete all as specified and as directed.

S&F in repairs white /black plastic seat cover solid confirming to ISI any type complete all as specified and directed.

Supply and fix 10 Litre capacity PVC low level flushing cistern with ball valve and handle/push button 32mm dia PVC flush pipe including taking down unserviceable cistern complete as in repairs all as specified and directed.

S&F Towel Rail 600 mm long 20mm dia,D type cromium plated, fixed with and including Chromium plated brass screws and wooden/plastic cleats. and fixed in repairs all as specified and directed.

S&F Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) and fixed in repairs all as specified and directed.

S&F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) and fixed in repairs all as specified and directed.

S&F Sheet glass assembely consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long above WHB.

S&F health faucet with fluxi pipe and hand shower the length of hose 1m fitted to the tap make JAGUOR Code ALD CHR 565 or equivalent in Hindware/Cera.

S&F CP 2 way bib cock, Make JAGUAR Cat No 38041 or equivalent in Hindware/Cera

Taking down Chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frames)

Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (Without taking off shutters from the frame)

S & F Solid PVC Door Frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with M S Square tube,supplying and fixing in opening as per manufacturers instructions and as directed by Engineer-in-Charge.

S & F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails .M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail ,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/scaled to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement and fixing in the frame as per manufacturers instructions and as directed by Engineer-in-Charge.

S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified.

S & F, 35mm thick, 2nd class hardwood glazed & skelton shutters, open rebated & prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part-I section 8 clause 8.20 (a).

Hacking out old broken glass (any thickness, size, quality or description) from metal frames or stone, concrete or bricks surrounds, glazed with putty or fixed with beads

S&F 4mm thick sheet glass ordinary quality fixing with putty/beading in square in each pane.

S&F MS Framed work such as grills or gratting etc with ends of bars welded of any size and any design including welding all as directed of Fe 290 Grade E-165.

S&F mild steel flat iron hold fast of any size and any similar articles confirming Fe 290 Grade E-165.

S & F, steel windows with side hung shutters including projecting type hinges with steel handle & steel peg stay, complete with glazing bars, dovetailed or welded including taking down the old window.

S&F for 75mm Butt hinges, medium weight, cold rolled mild steel, and fixed

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

M&L Preparation of new wooden Surfaces of any description over 10cm width or girth and appling two coats of synthetic enamel paint over a coat of pink primer.

M&L Preparing new steel Surfaces of any any description over 10cm width or girth and appling two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete.

Supply and fix floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring of 150 MM long. fixed in floor

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy.

S&F 150mm long aluminium anodised barrel tower bolt of extruded section

S&F 150mm long Extruded aluminium alloy handles, fabricated type, anodised.

S & F 100 mm long medium weight, cold rolled mild steel Butt hinges.

Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and as directed by Engineer-in-charge.

M&L for Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed

S&F for fixing 12mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface with sunk or raised moulding or over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately) complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new plastered/ceiling surface and applying two coat of distemper complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete not exc.15 cm thickness in ground/1st floors including floor tile complete including removal of debries to a distance exc. 150 m and not.exc. 200 all as specified and directed.

M&L 25 mm thick cement concrete 1 : 2 : 4 type B-1 (using 20mm graded crushed stone aggregate) laid in base, cement concrete surface even and smooth w/o using extra cement.

M&L for 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes.

M&L for Vitrified ceramic coloured /printed tiles double charged of area exc 0.42 sqm and n.exc 1.00 Sqm, 10 mm thick, in floors/skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles. (Screed bed shall be measured and paid for separately) complete all as specified and as directed

Taking down chowkats or frames exc. 1.5 Sq mtr but n. exc 4 Sqm each with shutters without taking off shutters from the frames complete all as specified and as directed by the Engineer-in-Charge

Taking down chowkats or frames not exc. 1.5 Sq mtr each with shutters without taking off shutters from the frames complete all as specified and as directed by the Engineer-in-Charge

M&L for powder coated aluminium frame for doors, windows (fixed/ sliding), ventilators with one or more rebates including joining cleat for fixing etc. including Powder Coating (minimum thickness of powder coating 50 micron) complete all as specified

S&F powder coated aluminium window shutters powder coating of any colour (Thickness or powder coating not less than 50 micron)., sliding type three track, two for fixing glass sections and one shutter with wire mesh aluminium section weighing 0.55 kg/Rm including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as handles and locking arrangement complete all as specified and directed. Note : Glass and Wire cloth will be measured and paid seperately under relevant item.

M&L for Anodised aluminium door shutter, aluminium section weighing 0.55 Kg per M including necessary jointing cleats, glazing clips rubber neoprene packing, handles 2 nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified Note : Glass will be measured and paid seperately under relevant item

S & F Aluminium (Die cast ) body door closer hydrolically regulated designation No.3 universal type suitable for door shutters of 851 to 1000mm in width and wt between 61 to 80 kgs.

S & F MS Mortice lock 4 leavers vertical type size 100mm

M&L for 12mm thick plywood, grade BWR, type BB, fixed complete all as specified and as directed.

M&L for Sheet glass, 5.5mm thick ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified

M&L for Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified

S & F PVC wall lining consisting of 5mm thick colour PVC sheets inclusive of solvent cement and fixing at site on PVC frame as per specification and directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

Taking down carefully copper/ aluminium point wiring (light, fan,socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good disturbed surfaces of walls, floors etc. complete all as specified and as directed by the Engineer-in-charge.

Taking down carefully MCB DB SPN/TPN, Metal P&S alongwith MCBs complete and taking credit all as specified and as directed by the Engineer-in-charge.

M& L for point wiring complete with 1.5 sq mm single core PVC insulated FRLS cable, with multi standard copper conductors, 1100 volts grade, drawn thorough and including PVC Conduit including provisoin of 1.5 sqmm PVC insulated copper cable FRLS as earth continuity conductor, including teminal box and hylum sheet of suitable module and for fixing switches /sockets/ regulators etc.all specified for :-

(a) One light point controlled by one way switch .

(b) One ceiling fan/ exhaut fan point controlled by one way switch.

(c) One 3 pin socket outlet 5 Amps on the same board with other switches.

(d) One 3 pin socket outlet 5 Amps independent

(e) One bell/ buzzer point controlled by one push button on the same board with other switch or on independent board.

(f) All as per item here-in-before but with 4.0 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 4.0 Sq mm copper conductor green in colour as earth continuity conductor complete all as specified and as directed by the Engineer-in-charge.

S&F Switch Piano, flush type single pole, one way 5 Amps.

S&F Socket outlet 2 in 1, 3 pin, 6A flush type

S&F Switch socket combination, 2 in 1, 3 Pin, flush type 5 Amps.

S&F switch socket combination, 2 in 1, 5 Pin, flush type 5&15 Amps.

S&F Bell push suitable 230 V

S&F stepped type electronic fan regulator flush type

M&L for Sub main wiring complete with two runs of 4 Sq mm Single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable with One run of 4.0 Sq mm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including suitable size of PVC conduit and accessories complete all as specified and directed.

M&L for Sub main wiring complete with four runs of 6 Sq mm Single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable with One run of 6 Sq mm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through existing PVC Conduit including taking down old u/s sub main wiring complete all as specified and as directed.

Cutting chases in wall/concrete floor/roof for laying PVC conduit and making good to facings where required and pointing in cement mortar 1:3, and making good, cutting not exc 10cm girth.

S&F Angle Holder with LED Bulb 9 Watt completed all as specified and as directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative batten type with driver, holder LED tube light fitting connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing LED lights fitting 1x 10W, 220V, AC decorative batten type with driver, holder LED tube light fitting connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by Engineer in Charge

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection completeall as specified and directed

S&F in repair street light bracket made up of GI pipe light grade 32 mm dia length 1.5 RM bent to shape with MS clamps, bolts, nut & washers complete, including taking old bracket of any size all as specified and as directed

S&F ceiling rose 3 terminal PVC/Polycarbonate insulated body.

S&F bell, Ding Dong AC, 230 volts all as specified and as directed

Taking down existing ceiling fan from it's position and re-fixing the same after cleaning the dust and connecting up including provision of cable from ceiling rose/ connector to fanall as specified and as directed.

Taking down existing Gyser of any capacity from it's position and re-fixing the same completion of necessary wall repair work and connecting up in to inlet and outlet stop valve complete all as specified and directed complete all as specified and as directed.

Taking down unsv GI Pipe and S&F GI tubes, medium grade fixed complete to wall and ceiling or laid in floor of size 15mm with all fittings and fixing complete including necessary excavation, clips, wall hooks, wooden plugs etc and fitting with existing pipe line of any size complete all as specified

Taking down unsv stop valve and Supply and fix 15mm bore stop valve fancy type, chorimum plated down high pressure, with or without leetterd Hot or Cold , screwed for 15mm , iron pipe all as specified and as directed.

Taking down unsv bib tap and Supply and fix, fancy type, 15mm bore chromium plated bib taps, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for bass ferrule, fancy type all as specified and as directed.

Taking down unsv PVC Connection pipe and S&F PVC connection pipe of size 15 x 450mm complete with PTMT nuts complete all as specified and directed.

Providing suitable hole in brick /stone masonary or any type of wall for exhaust fan of upto 300 mm sweep and repair to the wall to give smooth finish as existing to the disturbed surface of wall all as specified and as directed

Supply and fix louvers/shutters made of galvanised sheet to open and close opening/hole made for exhaust fan of size 300 mm dia automatically complete including necessary plaster work for edging the hole complete all as specified and directed

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm

Supply & fix MCB DB TPN 6 way double door with neutral bar etc all as specified and directed. (Note: Incomer & outgoing MCBs will be measured and paid seperately)

Supply & fix MCB DB SPN 12 way double door with neutral bar etc all as specified and directed. (Note: Incomer & outgoing MCBs will be measured and paid seperately)

Taking down unsv metal enclosure and S&F single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps for incoming and out going control, complete all as specified and directed.

Supply & fix MCB TPN (Moulded Case Circuit Breaker) upto 40 to 100 Amps, 16KA, 3 pole, 415V suitable for all as specified and directed.

Supply & fix MCB TPN (Moulded Case Circuit Breaker) upto 32 Amps, 16KA, 3 pole, 415V suitable for all as specified and directed.

Supply & fix MCB SP 6-32 Amps, 10KA, C Curve, 240V all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode of size 600mmx 600mm x 6 mm thick, buried directly in ground vertically to a depth not less than 2.25mtr below ground with top edge of the earth plate not less than 1.5 mtr below normal gound level, earth plate shall be connected with double bolts, nuts, check nuts & washers, to & including 4 mm galvanised iron wire as earth lead, extended upto 7.5 m or upto test terminal point, drawn through 20 mm dia med grade GI Pipe for protection of galvanised iron strip in the ground further connecting with GI wire 4mm dia to Distribution board, including excavation, earth work, charcoal, PCC Chamber, RCC Cover slab, watering pipe 20mm dia bore med grade wire net, funnel etc & testing on completion all as specified in plate No 3 of SSR Pt-I including taking down old u/s earthing . Note . (a) GI Pipe for protection of earthing wire and earth strip beyond 7.5 mtr or test point shall be measured and paid seperately under relevant items.

M&L for GI wire 4mm dia as earth continuity wire including taking out the old unsv earthing lead

Supply & fix MCB DB TPN 4 way double door with neutral bar etc all as specified and directed. (Note: Incomer & outgoing MCBs will be measured and paid seperately)

KOGANTI CONSTRUCTION COMPANY (BID ID -3137041)

NEWS CONSTRUCTIONS (BID ID -3139084)

RAJU AND COMPANY (BID ID -3138038)

STANDARD AGENCIES (BID ID -3137824)