GE/S(U)-04/2021-22 SPL REPAIR TO AREA DRAINAGE AND OTHER ALLIED WORKS AT HQ NC CAMP PROVN OF DIVERSION OF DRAINAGE LINE NEAR BLDG NO P-49C ADDN/ALTN OF BLDG NO NP-55 OF NCCIU ROOF AND CERTAIN WORK IN BLDG NO P-15 AND P-17 AT COMMAND CAMP OF HQ NC AND

Amount

Dismantling AC corrugated or semi corrugated sheet as in roof covering complete all as specified and directed.

Dismantling framed work timber scantlings 40 Sqcm and over in section, in any position any description or work complete all as specified and directed.

Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick crimpted/tapard at the external end slop of any colour having tansile strength 550 Mpa as in roof covering fixed with self tapping screws and caps etc. complete all as specified and directed.

Plain galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick in ridges, hips, valley gutters, wall cladding at the external end slop of any colour having tansile strength 550 Mpa as in roof (ridges) covering fixed with self tapping screws and caps etc. complete all as specified and directed.

Mild steel screw bolt (machine made) 11 to 15 mm dia with hexagonal or square heads at one end and screw the other, or screwed both end to be fitted with washers and one hexagonal or squre nut exceeding 10 cm & not exceeding 15 cm long complete all as specified and directed.

Rolled section Fe-410-W (Gde-E-250) quality-A as in main and cross beams, hip and jack rafters, purlins where connected to comman rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates complete all as specified and directed.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing; frame work for water tanks staging/caging and similar work confirming to Fe 290 Gd E-165 complete all as specified and directed.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide chrome primer complete all as specified and directed.

Demolition of Brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pilars etc. but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

Brick work with sub class "B" bricks straight or curved on plan exceeding 6 Metre mean radius in cement mortar 1:4 complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards any thickness including cover fillets complete all as specified and directed.

Anodised aluminium snap grid of size 605 x 605 mm for false ceiling complete all as specified and directed.

4 mm thick E board (designer ceiling) of size 600 mm x 600 mm panel confirming to IS 14862 type B category complete all as specified and directed. Make : Everest or equivalent

2nd class Hard wood clean sawn as in scantling fixed with nails exceeding 6 Sqcm and not exceeding 13 Sqcm in section complete all as specified and directed.

2nd class Hard wood clean sawn as in scantling fixed with nails exceeding 13 Sqcm and not exceeding 25 Sqcm in section complete all as specified and directed.

Demolition cement concrete in ground floors and paving (unreinforced) not exceeding 15 cm thickness (below or above ground floor) complete all as specified and directed.

75 mm thick plain cement concrete, type C-1, (1:3:6) (using 20 mm graded aggregate) as in sub for flooring complete all as specified and directed.

Providing 100 mm thick, plain cement concrete type B-1, (1:2:4) (using 20 mm graded aggregate) as in sub base of floors complete all as specified and directed.

25 mm thick PCC type B-0 (using 12.50 mm graded aggregate) as in sub base for receiving floor finishes complete all as specified and directed.

Cement concrete 1:3:6 type C-1, 75 mm thick (using 20 mm graded stone aggregates) as in plinth protection finished fair and even with using extra cement complete all as specified and directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish of the premises complete all as specified and directed.

Screed bed or bedding layers of 15 mm thick cement mortar 1:4 for laying floor finishes complete all as specified and directed.

Vitrified coloured tiles, (Double Charge) 600 x 600 x 10 mm thick as in floor etc. set and jointed neat cement slurry and pointed with white or colour cement to match the shades of surfaces shade/color of tile as approved and complete all as specified and directed by Engr-in-Charge.

Rendering 10 mm thick on fair faces of brick work or concrete surface in CM 1:4 on vertical surfaces/backing coat complete all as specified and directed.

All as per ser item No 23 but skairting/dado complete all as specified and directed.

Glazed ceramic coloured tiles of size 300 x 600 x 7 mm wall tiles set and jointed in neat cement and in white/coloured cement to match with the colour of tile etc. complete all as specified and directed.

Granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including griding and polishing types complete all as specified and directed.

Moulding rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations half or full round complete all as specified and directed.

Taking down chowkhats or frame with shutter (without taking of shutter off shutters from frame) 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

Taking down chowkhats or frame with shutter (without taking of shutter off shutters from frame) not exceeding 1.5 Sqm each complete all as specified and directed.

Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm single side prelam PVC sheet/wood grain printed colour PVC sheet reinforced with MS Tube complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC C channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and wooden grain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of wooden grain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete all as specified and directed.

Second class hard wood plain solid straight chowkhats frames and Designing for Main doors Pannel shutter with wrought frmed on the solid rounded or chanbered put together with glue and pinned at joints including preservative treatment complete all as specified and directed to approved by GE. Note : Design for door shutter including this specification.

35 mm thick second class hard wood plain framed pannelled shutter (two panels) with lock rail and pannel or 9 mm BWP comerical ply or 12 mm venered particle board with comerical face venering on both faces. The size of rail and style as per IS-1003 part kilin seasoned complete all as specified and directed.

150 mm brass barrel tower bolts, with cast or sheet and rolled or cast bolts complete all as specified and directed.

Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts 300 mm complete all as specified and directed.

125 butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type C-12 complete all as specified and directed.

150 mm length brass handles, cast type, polished bright Extruded brass handles, fabricated type polished complete all as specified and directed.

French polishing on surfaces of any description width or girth including cleaning and prepairing the surface including a coat of wood filler on new works with two or more coats complete all as specified and directed.

Aluminium anodised barrel tower bolt of extruded section and fixed length of bolt 100 mm complete all as specified and directed.

Aluminium handle, cast type anodised size of handle 150 mm complete all as specified and directed.

4 mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

Applying two coat birla wall care putty on old plastered on wall surfaces including preparation of surface by brooming down or steel wire brushing, scrapping down vegetation growth, efflorscent salts and trading with oil greasy spot complete all as specified and directed with complete removing.

Two coats of oil emulsion distemper over a coat of primer including preparation of old/ new plastered surfaces of walls and applying two coat wall care putty surface complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

15 mm thick rendering in cement mortar (1:6) on other than fair face/ smooth finesh of brick or concrete surface complete all as specified and directed.

15 mm thick rendering in cement mortar (1:4) on other than fair face of brick or concrete surface complete all as specified and directed.

Applying two coat birla wall care putty on new plastered on wall surfaces including preparation of surface by brooming down or steel wire brushing, scrapping down vegetation growth, efflorscent salts and trading with oil greasy spot complete all as specified and directed.

Two coats of distemper oil emulsion over a coat of primer including preparation of new plstered surfaces of walls complete all as specified and directed.

Applying two coats of cement based paint over a coat of primer preparation of new plastered surfaces complete all as specified and directed.

Preparation of old painted plastered surfaces of walls of any description, over 10 cm girth or width including cornices and applying two coat of Acrylic weather proof exterior emulsion paint over a coat of primer( Apex aultima) complete all as specified and directed.

Taking up or down 20 mm bore pipes steel tubing and connections complete all as specified and directed.

GI pipe medium grade 20 mm bore in wall and ceiling or laying in floors, including new fittings as required at site complete all as specified and directed.

Taking up or down of 15 mm bore pipes steel tubing and connections complete all as specified and directed.

GI pipe medium grade 15 mm bore in wall and ceiling or laying in floors, including new fittings as required at site complete all as specified and directed.

Providing and injecting Antitermite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete all as specified and directed by Engr-in-Charge.

Kerb stone of 300 x 300 x 100 mm thick precasted plain cement concrete type B-0, 1:2:4, (using 12.5 mm graded crushed stone aggregate) including earth work for laying kerb stones complete all as specified and directed.

Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M in depth for foundation complete all as specified and directed.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm complete all as specified and directed.

Removing excavated soil to a distance exceeding 50 m and not exceeding 1.50 km out side defence land complete all as sepcified and directed by Engr-in-Charge.

PCC 1:4:8 type D-2 (using 40 mm graded aggregate) in foundation filling and mass concrete complete all as specified and directed.

Use & waste of form work sides of concrete foundations footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter complete all as specified for fair finished surfaces and complete all as specified and directed.

Reinforced cement concrete Design Mix M-25 as in foundation including rafts, footing, plinth beams, bases for columns etc. complete all as specified and directed.

Form work to sides of columns rough, Pillars, posts struts suare or rectangular finished surfaces of concrete complete all as specified and directed.

Reinforced cement concrete Design Mix M-25 as in columns, pillar, pier, posts etc. complete all as specified and directed.

MS drapery rod powdered coated 20 mm Dia including brackets and necessary fitting including removal of old one complete all as specified and directed by Engr-in-Charge.

Wooden finish curtain rod with bracket single holders or \double holders for curtain rods (matching with curtain rods with end stops as approved and complete all as specified and directed.

Dismantling of 500/1000 ltrs capacity water tank of any description including all connection and removing from site complete all as specified and directed.

Rotational moulded polyethylene water storage tanks 1000 ltr capacity (cylindrical veritcal with closed top) with threaded cap hoisted and fixed in position complete all as specified and directed.

Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for 20 mm bore pipe and fixed (Minimum weight 142 gms) as in repair complete all as specified and directed.

Powder coated anodised aluminium frames for doors, windows, ventilators and partiton wall with one or more rebates including jointing cleats for fixing and including rubber gasket for fixing glass panes etc. complete all as specified and directed.

Powder coated aluminium anodised window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary jointing cleat glazing clips, rubber packing, anodised aluminium snap beading screws etc. complete all as specified and directed.

Extruded aluminum powder coated handles, fabricated type 75 mm size complete all as specified and directed.

All as per ser item No 74 but collapsible type complete all as specified and directed.

Butt hinges 75 mm size, powder coated aluminium alloy with galvanised mild steel hinge pin anodised type C-21 complete all as specified and directed.

Powder coated 15 micron aluminium door of approved design complete all as specified and directed with all fixing arrangement including providing and fixing door handle, tower bolts, mortice lock 6 lever (Make - Harrison/Godrej) one on each door and aluminium Powder coated tower bolts 200 mm long (03 Nos on each shutters) and including 5 mm thick tinted glass pane of glazed shutter along with aluminium glazing beading of size 19.00 mm x 17.5 mm x 0.70 mm @ weight of 0.097 Kgs per RM including rubber gasket on both side complete alongwith neoprene lining. The member shall be made out of extended aluminium sesction comprising of :- (Size of the door shall be as per site requirement) (a) Door frame of size 95.25 mm x 44.50 mm x 1.70 mm @ 1.301 Kg/RM. (b) Shutter vertical member 85 x 44.50 x 1.56 mm @ 1.39 Kg per RM. (c) Shutter top member 83.50 x 44.50 x 1.54 mm @ 1.139 Kg per RM. (d) Shutter bottom member 101.60 x 44.50 x 1.60 mm @ 1.301 Kg per RM. (e) Shutter lock rail member 83.50 x 44.50 x 1.54 mm @ 1.139 Kg per RM. The actual measurement shall be taken, wastage shall be including in the rates, the above sections are from JINDAL/ INDAL/HINDAICO/WALCO extruion. The contractor is at liberty to choose high section from approved make with minor variation in sizes and weight as approved. However nothing extra shall be paid for over size and over weight section also.

Aluminium powder coated frame, window shutters (glazed, wire gauge and grill) side hung with aluminium window frame or chowkhat 1.5 mm thick aluminium powder coated of size 100 mm x 44.5 mm and window shutter frames glazed and wire gauze (middle, top rail, bottom rail) and styles 1.5 mm thick aluminum powder coated of size 44.5 x 44.5 mm including powder coated aluminium grill 50 mm x 50 mm aparture and all fitting such as rubber gasket, aluminium glazing clips locking cabinet, 5 mm thick tinted glass pane for glazed shutters, stainless steel wire mesh for gauge shutter and hook and eye for each shutter fixed with rubber gasket and glazing clip/aluiminium beads aluminium tower bolt 75 mm 02 Nos each shutter, aluminium butt hinges 75 mm 02 Nos in each shutter aluminium handle 100 mm 01 No in each shutter including all accessories complete all as specified and directed.

Anodised aluminium partition wall, window/ and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed.

12 mm thick toughened glass partition and similar work with fixing of stain less steel clit/stain less steel clamp and fixing aluminium frame wall and floor complete all as specified and directed by Engr-in-Charge.

18/19 mm thick plywood grade A (Termite treated/water proof), type BB fixed with screws to timber/iron frame work complete all as specified and directed. Make : Green Ply/Kit ply.

12 mm thick plywood grade A (Termite treated /water proof), type BB fixed with screws to timber/iron frame work complete all as specified and directed. Make : Green Ply/Kit ply.

0.9 mm thick decorative choice of lamination type-1 of surface finish, colour and pattern as approved adhesive as per manufacturers instructions complete all as specified and directed.

Supply only for 5 mm thick tinted glass pane for glazed fixing for aluminium partition/ Windows complete all as specified and directed by Engr-in-Charge.

Suspended false ceiling with 10-12 mm thick Gypboard, consisting of intermediate channel of 45 x 15 x 0.9 mm thick, perimeter angles of 20 x 30 mm thick for ceiling (frame work shall be suspended from soffits of roof with rawl plugs) finally joints shall be filled with jointing compound and paper tape and surface finished smooth including applying two coat of gypsum primer and two coats of oil bound distemper over a thin coat of wall care putty complete with design/pattern aproved and all as specified and directed by GE.

Gypsum/POP cornices and stepped/sunken mouldings of approved design complete all as specified and directed.

5-10 mm thick of designed mirror in fixing for wooden boarding cutting in planks with maching beading complete all as specified and directed by Engr-in-Charge.

Preparation new or old treatment of wall surfaces and applying texture designing paint over wall finished by applying two coats of special effect paint of Johnson & Nicholson or wall sticker pattern complete all as per direction of Engr-in-Charge.

Textured planks for walling/skirting/vertical clading planks planed one side and edges tongued and grooved or wood head less screws rabated and fixed with nails/ screws with play board Size 1215 x 165 x 12 mm thick, core HDF EI (High Density) 860-900 KG/M3 foxwood No 176 or euiqalient including drilling plugging to brick walls complete all as specified and directed.

MS flat iron as in wind ties, valley drip, gutter or discription etc. confirming to Fe 410-0 or Fe 310-0 including clamps complete all as specified and directed.

1.25 mm thick plain black mild steel sheeting in ridges hip, valley gutters drip and gutters and straight flashings (Length and girth as fixed) complete all as specified and directed.

Brick work in cement mortar (1:4) using old size sub class 'B' bricks in walling, straight or curved on plan to any radius in half brick thick wall complete all as specified and directed.

Rendering 15 mm thick in CM 1:6 on fair faces of brick/concrete finished even and smooth without using extra cement complete all as specified and directed.

New/old plaster surface of walls and applying two coat of oil bound distempers over one coat of primer and two coat of wall care putty complete all as specified and directed by Engr-in-Charge.

Providing false ceiling GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flages of 20 to 30 mm and web of 27 mm fixed to surrounding wall using screws at 452 mm C/C channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm C/c with GI cleat and steel expansion or suitable hanging from soffits\trusses\bracking supporting hanger compressing of GI wire complete all as sepcified and directed by Engr-in-Charge.

4 mm thick 600 x 600 mm size E-boards designer ceiling (Make; Everest of equvalent), fixed to GI grid work with screws and applying new surfaces two coat of distempers and one coat of primers complete all as specified and directed.

Complete removal of existing treatment and applying two coats of oil bound distemper over a coat primers with two coat of wall care putty complete all as specified and directed by Engr-in-Charge.

Complete removal of existing treatment applying two coat of cement base paint over a coat of primer paint on walls complete all as specified and directed by Engr-in-Charge.

Complete removal of existing treatment applying two coat of exterior emulsion paint over a coat of primer with thin wall putty (Apex Ultima colour code as approved by GE) on old decorated surfaces of any description complete all as specified and directed.

100 mm butt hinges, heavy wight cold rolled mild steel and fixed complete all as specified and directed.

Aluminium handles cast type anodised 125 mm long complete all as specified and directed.

250 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

Mild steel framed work such as grills, grating , gratings etc. with ends of bars shouldered and /or reiveted or forged into spike, framed guard bar, barred iron doors, ladder, framed bausters railing frame work for water tank and similar work confirming to Fe 290 Gde E-165 complete all as specified and directed.

Steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 sheet 1/3 to 3/3. (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Description all as per ser item No 104 here in before but without glazing bar complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 sheet 1/3 to 3/3. (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Stainless steel wire cloth 0.36 mm nominal and average width of apreture 1.40 mm and fixed with tinned teaks or wire staple complete including fixed in repairs complete all as specified and directed.

75 mm thick PCC 1:4:8 type D-2 (using 40 mm graded aggregate) as in sub base of floor etc. complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded aggregate) as in level course on floor etc. complete all as specified and directed.

15 mm thick cement plaster on fair face of brick or concrete surface in cement mortar 1:4, finished even and fair, as in backing coat to receive tiles complete all as specified and directed.

Machine cut kota stone flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed.

Machine cut kota stone 18-20 mm thick as in riser of step, skirting, dado and pillar laid over cement screed base including rubbing and mirror polishing and jointed with grey cement slurry mixed with pigment to match the shade of the slab complete all as specified and directed.

75 mm thick plain cement concrete, type C-1, (1:3:6) (using 20 mm graded aggregate) as in plinth protection complete all as specified and directed.

Excavation over areas not exceeding 1.5 m deep and getting out as in soft/loose/ black top road cuttting any type of soil complete all as specified and directed.

Excavation over areas exceeding 1.5 m but not exceeding 3.0 mtr deep and getting out as in Hard/dense complete all as specified and directed.

Plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in surface channels and drains, foundation, hanching and similar work etc. complete all as specified and directed.

PCC 1:2:4 type B-0 (using 12.5 mm graded aggregate) as in coping, benching and similar work etc. including necessary form work complete all as spcified and directed.

Brick work with sub class 'B' bricks straight or curved on plan exceeding 6 mtr mean radius built in CM (1:4) as in drain, walls and similar work etc complete all as specified and directed.

Walling of square/rectangular, random rubble, uncoursed well bonded, bedded and solidly hearted built in cement mortar 1:4 complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints as specified of random rubble walling, uncoursed or brought upto courses, hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 40 mm on lime/sand stone complete all as specified and directed.

Raised pointing to square/rectangular or random rubble masonry in CM 1:4 complete all as specified and directed.

Extra for forming fair finished drain or channel not exceeding 70 cm inner girth in cement concrete, using extra cement, including forms moulds, mitred/stopped ends etc complete all as specified and directed.

Precast reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) for drain, manhole, safety tank cover slabs etc. including necessary form work and set in CM (1:4) complete all as specified and directed. Note:- reinforcement will be measured and paid seperately.

Cement concrete work in pavements/hard standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less complete all as specified and directed.

Reinforced cement concrete Design mix M-25 in slab supported on walls, beams and columns complete all as specified and directed.

Formwork to soffits of suspeneded slabs such as roof slabs, floor slabs, landing and similar work complete all as specified and directed.

TMT bars 10 mm dia and over cut to length, bent to shape required including cranking bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

TMT bars 6-8 mm dia and cut to length bent to shape required including cranking, bending, hooking ends and bending with MS wire not less than 0.9 mm dia or securing with clips quality confirming complete all as specified and directed.

Precasted RCC jallies 45 to 50 mm thick (measured solid) including all mouldings but excluding frames confirming to type B-0 (using 12.5 mm graded crushed stone aggregate) complete all as specified and directed.

12 mm thick rendering on fair faces of brick/ stone surfaces finished even and smooth without using extra cement in CM 1:4 complete all as specified and directed.

Precasted RCC jallies 45 to 50 mm thick (measured solid) including all mouldings but excluding frames confirming to type B-0 (using 12.5 mm graded crushed stone aggregate) complete all as specified and directed.

Reinforced concrete pipes 600 mm boreof pipe, class NP-3, laid and jointed complete with collars complete all as specified and directed.

Plain cement concrete 1:2:4 type B-2 (using 40 mm graded stone aggregate) as in surface channels and drains, foundation and similar work etc complete all as specified and directed.

All as per ser item No 117 but except bricks complete all as specified and directed.

All as per ser item No 118 but except stone complete all as specified and directed.

Raking out joints/pointing square/rectangular or random rubble masonry, coursed or uncoursed, random rubble or polygonal rubble uncoursed or brought up to courses complete all as specified and directed.

Flush pointing to square/rectangular, random rubble masonry, uncoursed or brought upto course masonary in CM 1:3 complete all as specified and directed.

Raised pointing to square/rectangular or random rubble or polygonal rubble, uncoursed on brought upto courses random rubble stone masonary in CM 1:4 complete all as specified and directed.

PVC pipe 110 mm dia low density of pressure rating 10 Kg/Sqcm (in short lengths) fixed in floor/walls as weep holes as in retaining wall/ drain complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded aggregate) as in level course on floor etc. complete all as specified and directed.

Rendering 10 mm thick in CM 1:3 mixed with integral water proofing compound as per manufacture's instructions as in roof and chajjas, finished the surface fair and even with out using extra cement complete all as specified and directed. Note : Supply of water proofing compound will be measured and paid separately.

Supply only integral water proofing compound complete all as specified and directed.

Three coats of white wash on newly plastered surfaces of wall including preperaton complete all as specified and directed.

105 x 60 mm pressed steel frames for doors with one or more rebate including necessary fixing lungs, hinges lock strike plate etc complete all as specified and directed including a coat of shop coat zinc chrome primer.

200 mm long mild steel tower bolt stove enamelled black, with bright bolt and fixed complete all as specified and directed.

300 mm long mild steel sliding door bolts plate type sove enamelled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on stapple plate complete all as specified and directed.

100 mm long mild steel medium weight but hinges cold rolled complete all as specified and directed.

150 mm mild steel pressed handles oval type stove enamelled black complete all as specified and directed.

Preparation of new/old wooden surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in any type of soil complete all as specified and directed.

75 mm thick PCC type C-2 1:3:6 (using 40 mm graded crushed stone aggregate) as in sub base for receiving floor finishes finished even and fair complete all as specified and directed.

25 mm thick PCC type B-0 (using 12.50 mm graded crushed stone aggregate) as in sub base for laying floor finishes complete all as specified and directed.

Sand cushioning/filling under floors for laying interlocking tiles complete all as specified and directed.

Machine pressed precast concrete interlocking paver blocks lacquor finish any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment complete all as specified and directed.

RCC/PCC type B-1 (1:2:4) (using 20 mm graded cushed stone aggregate) as in coping, benching, lintel bands and the like including form work any type complete all as specified and directed.

Raised pointing to square/rectangular, random rubble stone masonary in CM 1:3 complete all as specified and directed.

Surface dressing not exceeding 15 cm deep in hard/dense soil complete all as specified and directed.

Reinforced cement concrete (nominal mix) type B-1 1:2:4 (using 20 mm graded aggregate) using footing, foundation beams, plinth beam, roof beam, lintel band and similr work etc. complete all as specified and directed.

Reinforced cement concrete (nominal mix) type B-1 1:2:4 (using 20 mm graded aggregate) using columns, pillars and similar work etc. complete all as specified and directed.

RCC type B-1 1:1 1/2:3 (using 20 mm graded aggregate) for slabs supported on walls beams and columns in floors, roof, landing, balconies, canopies slabs and in shelves and the like complete all as specified and directed.

RCC type B-1 1:1 1/2:3 (using 20 mm graded aggregate) for chajjas complete all as specified and directed.

Form wotk to edges of concrete flat slats sides of RCC/PCC bands etc in walls horizontal or slopping exceeding 10 cm but not exceeding 20 cm wide rough finished surfaces complete all as specified and directed.

Form work to soffits of suspended slabs such as roof slabs, landing and similar work not exceeding 200 mm thick complete all as specified and directed.

Form work to chullahah hoods chajjs ,trought and similar items rough finished surfaces of concrete complete all as specified and directed.

Form work to sides and soffit of floor or roof beams, lintels beam, coloumn and similar work etc complete all as specified and directed.

All as per ser item No 126 but 5 mm dia and over up to and including 10 mm dia as in stirrups complete all as specified and directed.

Rendering 5 mm thick in CM 1:3 on ceiling and exposed surface of concrete finsihed even and smooth without using extra cement complete all as specified and directed.

Preparation of new plaster surfaces applying three coats of white wash on ceiling complete all as specified and directed.

Hard core of guage not exceeding 63 mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface complete all as specified and directed.

Taking down carefully, copper/aluminum point wiring (light, fan, socket or power/LED Light fittings) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as specified and directed. Keeping the LED lights in safe custody.

Point wiring for one light/fan/bell point controlled by one switch using 1.5 Sqmm FRLS copper conductor cables (multistranded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5 mm and 20 mm dia), medium grade with Modular metal flush boxes thickness (1.25 mm) & PVC back plate for mounting modular type in adequate module of switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts copper conductor cable 1.5 Sqmm as earth wire stranded and conected to earth dolly complete all as specified and directed. Make: Havells/ Finolex/Polycab/L&T

All as per ser item No 170 but for 3 pin 6 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 Sqmm earth wire and connected to earth dolly complete all as specified and directed.

All as per ser item No 170 but for 3 pin 6 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 Sqmm earth wire and connected to earth dolly complete all as specified and directed.

All as per ser item No 170 but for 3 Pin 16 Amps socket outlet independent with cable 2.5 Sqmm including copper PVC insulated PVC unsheathed 1.5 Sqmm earth wire standard and connected to earth dolly complete all as specified and directed.

All as per ser item No 170 but for one 3 Pin 15 Amps socket outlet independent with cable 4.0 Sqmm including copper PVC insulated PVC unsheathed 2.5 Sqmm earth wire standard and connected to earth dolly complete all as specified and directed.

Switch Piano flush type 6 Amps single pole one way (Modular Type) with outer strip complete all as specified and directed. Make: Havells (Crabtree)/Legrand/Philips

Switch Piano flush type 16 Amps single pole one way (Modular Type) with outer strip complete all as specified and directed. Make: Havells (Crabtree)/Legrand/Philips.

Socket 2-in-1, 3 Pin 6 Amps (Modular Type) with outer strip complete all as specified and directed. Make: Havells (Crabtree)/Legrand/ Philips

Socket 2-in-1, 3 Pin 6 & 16 Amps (Modular Type) with outer strip complete all as specified and directed. Make: Havells (Crabtree)/ Legrand/ Philips.

Electronic step type fan regulator 120 watt 230 volts 50 C/S deluxe modular type complete all as spcified and directed. Make: Havells (Crabtree)/Legrand/Philips.

Ceiling rose surface bakelite 3 terminals complete all as specified and directed. Make : Cona Cat Part No 2126/SSK Cat Part No 572 or equivalent of make in Havells/Legrand /Polycab

Single pole and neutral enclosure surface mounted 240 volts with 2 pin and earth plug and socket with one single pole MCB 20 Amps with indicator of make wipro/equivallent in Havells/Bajaj/Philips/Schneider complete all as specified and directed.

15W LED 6500K Slim, compact, auminum die cast edge lit panel, recess mounted round fixture with opal diffuser and separate electronic driver. Make - Havells Cat Part No LHEBHDP7IZ1W015 or equivalent to Wipro/ Philips/ Bajaj/HPL complete all as specified and directed by Engineer-in-Charge.

Replacement sheet metal enclosures for DBs when MCBs to be used double door DB TPN 4 way 415 volts with 200 amps rated bus bar complete all as specified and directed. Make : Havells/Schneider/Legrand/Siemens.

Replacement MCB DB TPN 100A DD 04 Way IP43 with MCCB Box complete all as specified and directed. Make : Havells/Schneider/ Legrand/Siemens.

Replacement MCB Single Pole, 230 Volt, Rating 6 to 32 Amps complete all as specified and directed. Make: Havells/Schneider/ Legrand/Siemens.

Hanging Ceiling fan 1200 mm sweep complete set without regulator including connecting to ceiling rose with twin twisted flexible cooper cable and provisioning of suitable fan hook/ down rod including all accessories as per site requirement Fusion 50 Metallic Beige-Brown / Pearl Ivory-Gold complete all as specified and directed. Make :- Havells or equivalent to Bajaj/ Philips/Crompton.

Exhaust fan Ventil Air - DB 300 mm including louver complete all as specified and directed. Make - Havells/Bajaj/ Philips/Crompton

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 10 Sqmm in PVC concealed conduit 25 mm dia including PVC insulated copper conductor cable 6 Sqmm as earth lead complete all as specified and directed. Including taking down old sub main wire. Make: Havells/Finolex/Polycab/L&T

New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 20 W complete all as specified and directed by Engr-in-Charge. Make-Havells Cat Part No LHEXBXPNIN1W020 or equivalent to Crompton/Syska.

Replacement 36W (2 x 2) LED Ceiling light flat panel for surface mounting which provides soft-light and glare free symmetrical illumination complete all as specified and directed. Make - Havells, Cat Part No PLUTOSURFACE2X2PLS34WLED857S or equivalent to HPL/Phillips/Wipro.

Sheet metal enclosures for DBs when MCBs to be used double door DB SPN 8 way 240 volts with 200 amps rated bus bar and neutral link in cluding chases wall for dixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Make: Havells/ Schneider/Legrand/HPL/Siemens

Sheet metal enclosures for DBs when MCBs to be used double door DB SPN 4 way 240 volts with 200 amps rated bus bar and neutral link in cluding chases wall for dixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Make: Havells/ Schneider/Legrand/HPL/Siemens.

MCB SPN (Isolator), 240 Volt, Raiting 40 Amps complete all as specified and directed. Make: Havells/Schneider/Legrand/HPL/Siemens

Earthing complete with galvanised steel earth plate electode 600 mm x 600 mm x 6.00 mm thick burried directly in ground (earth pit not less than 2.25 meter deep below normal ground level connected to and including galvanised steel earth lead wire 4 mm dia by means of bolts, nuts, chock, nuts and washers of galvanised iron or steel including PCC Pit in 1:2:4 type B-1 angle iron frame with RCC cover and handle, excavation and earth work in any type of soil medium grade GI watering pipe 20 mm bore with funnel and wire mash and light grade GI protection pipe 15 mm bore upto main board complete all as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected to main control board complete all as specified and directed and testing completion.

Supply & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 10 Sqmm x 2 core size complete all as specified and directed. Make: Havells/ Finolex/Polycab. Note : Earth work and other connected work shall be measured & paid sperately.

Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete all as specified and directed. Note : for payment purpose punned thickness shall be measured

Bricks sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and directed.

GI tubing light grade 25 mm dia along the wall/ in trenches/in duct/in culvert/road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles complete all as specified and directed.

RAJ MOHD

RAMAN CONSTRUCTION CO

paras ram pachiala