Development of various tourism infrastructures at Sitakund Waterfall Site

CIVIL-Earth work in excavation of foundation trenches in all kids of soil including dressing and levelling the bed upto the required depth and depositing the excavated materials with all leads & lifts T&P shoring and shuttering watering if necessary etc. complete as per directed by the Engineer-in-charge

CIVIL-Filling foundation trenches with excavated earth including watering ramming and compacting in layer not exceeding 150 mm thick including labour sundries T & P etc. complete and as per direction of Engineer-in- charge

CIVIL-Excavation of any approved type of soil in approved borrow area by mechanical means loading into & transportation by mechanical means and unloading the soil within initial lead of 1km on properly prepared and scientifically approved surface including spreading and levelling the earth in 22.5cm layers to make ready for watering and compaction with sheep foot rollers and dozers but excluding watering and compaction in dams and dykes for all heights including construction , maintenance , watering and lighting of haul road and borrow area etc. complete as per direction of Engineer -In-Charge.( measurement of the fill to be taken on the finished compacted section)Providing filling foundation and plinth with sand well-watered and rammed with rammer including cost of all materials and labour T & P etc. complete.

CIVIL-Supplying & filling in foundation and plinth with good quality river sand including watering, ramming with cost, conveyance, royalties, taxes of all materials and cost of all labour with T&P, sundries required for the work etc., complete (Measurement will be taken on finished compacted section) as per specification and direction of Engineer-in-charge.

CIVIL-Cement concrete(1:3:6 ) using 40 mm size B.H.G C.B chips laying in layers not exceeding 150mm ramming in rammer, watering and curing etc.

CIVIL-Fly-Ash Brick masonry with c.m (1:6) in foundation and Plinth using Fly-Ash Bricks 250 x 120 x 81mm size watering ,curing etc complete including cost of materials, labour all comp. complete as per the direction of Engineer-In-Charge

CIVIL-Providing, lifting, hoisting and laying R.C.C of M-25 grade in Column base, Column Footings, Raft Foundation, Stem of the Columns, beams, chajja, fin, lintel, stair Case, jali , shelves and slab etc as per approved designs and drawings having a minimum Compressive strength ( in work test) 20N. / Square mm. in 15cm. cubes at 28 days after mixing and test conducted in accordance with 1.S. 456 and 1.S. 516 using screened & washed sharp Hiver sand far mertar and 18mm. to 20 mm. size black hand crusher broken granite stone chips of approved quality from approved quarry, washed and cleaned to be mixed in concrete mixture with approved quality of cement Including hoisting, lowering, laying and compacting concrete by using vibrators, watering and curing for 29 days including, centering and shuttering then after {dismantling and removing the debrises away from the work site and finishing the exposed ~ Surface -smooth. providing grooves-or beads: wherever necessary. including: cost, conveyance, loading, unloading, royalties and taxes of all materials , cost of all labours, scaffolding, sundries, T&P required for the work etc. Complete in all respect but the excluding cost & conveyance of M.S. rods or Tor Stee! and Binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or Tor steel and binding wires and tying the grills and placing in. proper position as directed by the Engineer-in-charge.- Footing

CIVIL-Providing, lifting, hoisting and laying R.C.C of M-25 grade in Column base, Column Footings, Raft Foundation, Stem of the Columns, beams, chajja, fin, lintel, stair Case, jali , shelves and slab etc as per approved designs and drawings having a minimum Compressive strength ( in work test) 20N. / Square mm. in 15cm. cubes at 28 days after mixing and test conducted in accordance with 1.S. 456 and 1.S. 516 using screened & washed sharp Hiver sand far mertar and 18mm. to 20 mm. size black hand crusher broken granite stone chips of approved quality from approved quarry, washed and cleaned to be mixed in concrete mixture with approved quality of cement Including hoisting, lowering, laying and compacting concrete by using vibrators, watering and curing for 29 days including, centering and shuttering then after {dismantling and removing the debrises away from the work site and finishing the exposed ~ Surface -smooth. providing grooves-or beads: wherever necessary. including: cost, conveyance, loading, unloading, royalties and taxes of all materials , cost of all labours, scaffolding, sundries, T&P required for the work etc. Complete in all respect but the excluding cost & conveyance of M.S. rods or Tor Stee! and Binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or Tor steel and binding wires and tying the grills and placing in. proper position as directed by the Engineer-in-charge.-Pedestal

CIVIL-Providing, lifting, hoisting and laying R.C.C of M-25 grade in Column base, Column Footings, Raft Foundation, Stem of the Columns, beams, chajja, fin, lintel, stair Case, jali , shelves and slab etc as per approved designs and drawings having a minimum Compressive strength ( in work test) 20N. / Square mm. in 15cm. cubes at 28 days after mixing and test conducted in accordance with 1.S. 456 and 1.S. 516 using screened & washed sharp Hiver sand far mertar and 18mm. to 20 mm. size black hand crusher broken granite stone chips of approved quality from approved quarry, washed and cleaned to be mixed in concrete mixture with approved quality of cement Including hoisting, lowering, laying and compacting concrete by using vibrators, watering and curing for 29 days including, centering and shuttering then after {dismantling and removing the debrises away from the work site and finishing the exposed ~ Surface -smooth. providing grooves-or beads: wherever necessary. including: cost, conveyance, loading, unloading, royalties and taxes of all materials , cost of all labours, scaffolding, sundries, T&P required for the work etc. Complete in all respect but the excluding cost & conveyance of M.S. rods or Tor Stee! and Binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or Tor steel and binding wires and tying the grills and placing in. proper position as directed by the Engineer-in-charge.-Pedestal upto NGL

CIVIL-Providing, lifting, hoisting and laying R.C.C of M-25 grade in Column base, Column Footings, Raft Foundation, Stem of the Columns, beams, chajja, fin, lintel, stair Case, jali , shelves and slab etc as per approved designs and drawings having a minimum Compressive strength ( in w

ork test) 20N. / Square mm. in 15cm. cubes at 28 days after mixing and test conducted in accordance with 1.S. 456 and 1.S. 516 using screened & washed sharp Hiver sand far mertar and 18mm. to 20 mm. size black hand crusher broken granite stone chips of approved quality from approved quarry, washed and cleaned to be mixed in concrete mixture with approved quality of cement Including hoisting, lowering, laying and compacting concrete by using vibrators, watering and curing for 29 days including, centering and shuttering then after {dismantling and removing the debrises away from the work site and finishing the exposed ~ Surface -smooth. providing grooves-or beads: wherever necessary. including: cost, conveyance, loading, unloading, royalties and taxes of all materials , cost of all labours, scaffolding, sundries, T&P required for the work etc. Complete in all respect but the excluding cost & conveyance of M.S. rods or Tor Stee! and Binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or Tor steel and binding wires and tying the grills and placing in. proper position as directed by the Engineer-in-charge.-Coloumn

CIVIL-Providing, lifting, hoisting and laying R.C.C of M-25 grade in Column base, Column Footings, Raft Foundation, Stem of the Columns, beams, chajja, fin, lintel, stair Case, jali , shelves and slab etc as per approved designs and drawings having a minimum Compressive strength ( in work test) 20N. / Square mm. in 15cm. cubes at 28 days after mixing and test conducted in accordance with 1.S. 456 and 1.S. 516 using screened & washed sharp Hiver sand far mertar and 18mm. to 20 mm. size black hand crusher broken granite stone chips of approved quality from approved quarry, washed and cleaned to be mixed in concrete mixture with approved quality of cement Including hoisting, lowering, laying and compacting concrete by using vibrators, watering and curing for 29 days including, centering and shuttering then after {dismantling and removing the debrises away from the work site and finishing the exposed ~ Surface -smooth. providing grooves-or beads: wherever necessary. including: cost, conveyance, loading, unloading, royalties and taxes of all materials , cost of all labours, scaffolding, sundries, T&P required for the work etc. Complete in all respect but the excluding cost & conveyance of M.S. rods or Tor Stee! and Binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or Tor steel and binding wires and tying the grills and placing in. proper position as directed by the Engineer-in-charge.-Plinth Bend

CIVIL-Providing, lifting, hoisting and laying R.C.C of M-25 grade in Column base, Column Footings, Raft Foundation, Stem of the Columns, beams, chajja, fin, lintel, stair Case, jali , shelves and slab etc as per approved designs and drawings having a minimum Compressive strength ( in work test) 20N. / Square mm. in 15cm. cubes at 28 days after mixing and test conducted in accordance with 1.S. 456 and 1.S. 516 using screened & washed sharp Hiver sand far mertar and 18mm. to 20 mm. size black hand crusher broken granite stone chips of approved quality from approved quarry, washed and cleaned to be mixed in concrete mixture with approved quality of cement Including hoisting, lowering, laying and compacting concrete by using vibrators, watering and curing for 29 days including, centering and shuttering then after {dismantling and removing the debrises away from the work site and finishing the exposed ~ Surface -smooth. providing grooves-or beads: wherever necessary. including: cost, conveyance, loading, unloading, royalties and taxes of all materials , cost of all labours, scaffolding, sundries, T&P required for the work etc. Complete in all respect but the excluding cost & conveyance of M.S. rods or Tor Stee! and Binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or Tor steel and binding wires and tying the grills and placing in. proper position as directed by the Engineer-in-charge.-Floors

CIVIL-Providing, lifting, hoisting and laying R.C.C of M-25 grade in Column base, Column Footings, Raft Foundation, Stem of the Columns, beams, chajja, fin, lintel, stair Case, jali , shelves and slab etc as per approved designs and drawings having a minimum Compressive strength ( in work test) 20N. / Square mm. in 15cm. cubes at 28 days after mixing and test conducted in accordance with 1.S. 456 and 1.S. 516 using screened & washed sharp Hiver sand far mertar and 18mm. to 20 mm. size black hand crusher broken granite stone chips of approved quality from approved quarry, washed and cleaned to be mixed in concrete mixture with approved quality of cement Including hoisting, lowering, laying and compacting concrete by using vibrators, watering and curing for 29 days including, centering and shuttering then after {dismantling and removing the debrises away from the work site and finishing the exposed ~ Surface -smooth. providing grooves-or beads: wherever necessary. including: cost, conveyance, loading, unloading, royalties and taxes of all materials , cost of all labours, scaffolding, sundries, T&P required for the work etc. Complete in all respect but the excluding cost & conveyance of M.S. rods or Tor Stee! and Binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or Tor steel and binding wires and tying the grills and placing in. proper position as directed by the Engineer-in-charge.-RCC Slab

CIVIL-Providing, lifting, hoisting and laying R.C.C of M-25 grade in Column base, Column Footings, Raft Foundation, Stem of the Columns, beams, chajja, fin, lintel, stair Case, jali , shelves and slab etc as per approved designs and drawings having a minimum Compressive strength ( in work test) 20N. / Square mm. in 15cm. cubes at 28 days after mixing and test conducted in accordance with 1.S. 456 and 1.S. 516 using screened & washed sharp Hiver sand far mertar and 18mm. to 20 mm. size black hand crusher broken granite stone chips of approved quality from approved quarry, washed and cleaned to be mixed in concrete mixture with approved quality of cement Including hoisting, lowering, laying and compacting concrete by using vibrators, watering and curing for 29 days including, centering and shuttering then after {dismantling and removing the debrises away from the work site and finishing the exposed ~ Surface -smooth. providing grooves-or beads: wherever necessary. including: cost, conveyance, loading, unloading, royalties and taxes of all materials , cost of all labours, scaffolding, sundries, T&P required for the work etc. Complete in all respect but the excluding cost & conveyance of M.S. rods or Tor Stee! and Binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or Tor steel and binding wires and tying the grills and placing in. proper position as directed by the Engineer-in-charge.-Lintal

CIVIL-Cutting, Straightening coiled or bent up M.S plain HYSD/TMT reinforcement bars welding or| jointing if necessary bending,binding,tying the grills as required for R.C.C works,providing fan hooks where necessary and hoisting, lowering and placing in proper position according to approved designs and drawings including cost,canveyance,loading,..unloading & taxes of M.S PlaiwHYSD/TMT reinforcement bars and binding wires of 18 to 20 gaugo required for the work and cost of all labour, sundries, TP and Scaffolding complete in alt respect as directed by the Engineer in charge (payment will be made according to the actual weight of M.SPiainHYSD/TMT reinforcement bars consumed in the work only.

CIVIL-Brick work with Fly Ash bricks 25cm x 12cm x 8cm size having crusing Strength not less then 75kg/cm2 in cement mortar (1:6) in superstructure including all cost complete as per direction of Enginner-In-Charge.

CIVIL-6mm thick cement plaster (1:4) over R.C.C surface including all cost and conveyance, royalty, taxes of all materials etc.complete as directed by the Engineer in Charge.

CIVIL-Providing 12mm thick cement plaster in cement mortar (1:6) in all floors finished smooth to out, Side smooth surface of brick

walls after racking out joints, scrapping & cleaning the surface & finishing the plaster surface Smooth using wooden float only to proper plumbs & level and making necessary grooves, beads & drip course to give required omamental finish as per drawing, watering, curing, Scaffolding, screening sand etc. complete with cost, conveyances, royalties, taxes of all materials and cost of all Jabour with T&P, sundries required for the work etc. complete as per specification & direction of Engineer-in-charge

CIVIL-16mm thick cement plaster (1:6) on brick work inside wall including all cost conveyance royalty & taxes etc, to work site as per direction of Engineer-In-Charge

CIVIL-2.5cm thick A.S flooring with C.C (1:2:4) using 12 mm chips lowering and laying concrete with punning etc complete.

CIVIL-Providing and Painting wall Surface one coat with Wall Primer to give an even shed before applying weather coat to Exterior walls including cost of Primer , labour, T&P all comp.

CIVIL-Wall painting 2 coats with weather coat over a coat of primer to inside and out side smooth surface with all cost of labour, T&P material etc complete.

CIVIL-Providing,Fitting & Fixing of Granite Stone in Floors, steps &Landing slab over 25mm thick cement plaster in Cement Mortar (1:1) including cost of Tiles, Labour, T&P all comp.

CIVIL-Finishing wall surface of walls with Acrylic wall putty (Water based ) of approved make and finished smooth and even surface to receive painting including cost of scaffolding staging charges with cost of all materials taxes, labour T&P etc complete.

CIVIL-Wall painting two coats with Plastic emulsion paints over a coat primer of approved shade including cost and conveyance of all materials to site, and all labour charges complete as per direction of E.I.C..

CIVIL-Supplying, fitting and fixing vetrifed tile in floors of size 600mm x 600mm of approved make with application of polymer modified cement based water resistant adhesive bed of required thickness of 10mm and filling joints with epoxy grout of approved qualiy including cost of all materials, labour T&P etc required for the work.

CIVIL-Providing, Fitting & Fixing of Virtified tiles in Walls on 12mm thick Cement Plaster in Cement mortar (1:3) jointed with neat cement Slurry mixed with Pigments including cost of Tiles, labour, T&P all comp.

CIVIL-Supplying , fitting and fixing of two track UPVC sliding window of approved make with 6mm thick glass of approved quality complete with frame, shutters and all fitting and fixtures.

CIVIL-Supplying , fitting and fixing of openable UPVC doors with door frame of approved make with 6mm thick glass of approved quality complete with frame, shutters and all fitting and fixtures.

CIVIL-Water proofing treatment

CIVIL-Providing dry rubble rock toe with blasted and quarried granite boulders of sizes 30cm and above with all leads and lifts including dumping with packing interstices properly and surface packing to proper line and level complete as directed by the Engineer-in-charge. ( No deduction to be made towards voids in finished section.) (Cost of transportation to be added)

SEPTIC TANK. (50 USER) Size-(4x1.4x2) Mtr-Earthwork in excavation in all types of soil for site leveling, foundation, pits, trenches and other civil works up to and including 1.5 metre lift and stacking the soil upto a lead of 100 metre and including dewatering, removing slush, shoring and strutting (as required), complete as per specification and as directed by the Engineer-In-Charge.

SEPTIC TANK. (50 USER) Size-(4x1.4x2) Mtr-Filling at all depth with available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 15 cm in depth: consolidating each deposited layer by ramming and watering complete (lead upto 100m) as directed by the Engineer-In-charge.

SEPTIC TANK. (50 USER) Size-(4x1.4x2) Mtr-Supplying of filling sand in foundation and over areas including watering, ramming, consolidating and dressing, labours, tools, taxes etc. all complete as per the specification and direction of E.I.C.

SEPTIC TANK. (50 USER) Size-(4x1.4x2) Mtr-Providing and laying plain cement concrete 1:3:6 (1 cement:3 sand: 6 stone aggregate 40mm nominal size) as levelling course in foundation and plinth etc. including tempering, curing, shuttering etc. complete all depth and height.

SEPTIC TANK. (50 USER) Size-(4x1.4x2) Mtr-Providing, lifting, hoisting and laying Reinforced cement concrete of M-25 grade as per approved designs and drawings having a minimum compressive strength (in work test) 250 Kg. / Square cm. in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 516 using 12 mm. to 20 mm. size black hard crushed broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned ( 20mm. size chips not to exceeds 25 % ) to be mixed in concrete mixture with Portland slag cement (PSC) including hoisting, lowering, laying and compaction concrete by using vibrators, watering and curing for 28 days, centering and shuttering then after dismantling and removing debris from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required of the work etc. complete in all respect as directed by the Engineer-in-Charge. But excluding cost and conveyance of M.S. rods or Tor steel and binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or tor steel tying the grills and placing in proper position. A) Base - Septic tank

SEPTIC TANK. (50 USER) Size-(4x1.4x2) Mtr-Providing, lifting, hoisting and laying Reinforced cement concrete of M-25 grade as per approved designs and drawings having a minimum compressive strength (in work test) 250 Kg. / Square cm. in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 516 using 12 mm. to 20 mm. size black hard crushed broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned ( 20mm. size chips not to exceeds 25 % ) to be mixed in concrete mixture with Portland slag cement (PSC) including hoisting, lowering, laying and compaction concrete by using vibrators, watering and curing for 28 days, centering and shuttering then after dismantling and removing debris from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required of the work etc. complete in all respect as directed by the Engineer-in-Charge. But excluding cost and conveyance of M.S. rods or Tor steel and binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or tor steel tying the grills and placing in proper position.- Baffle Wall

SEPTIC TANK. (50 USER) Size-(4x1.4x2) Mtr-Providing, lifting, hoisting and laying Reinforced cement concrete of M-25 grade as per approved designs and drawings having a minimum compressive strength (in work test) 250 Kg. / Square cm. in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 516 using 12 mm. to 20 mm. size black hard crushed broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned ( 20mm. size chips not to exceeds 25 % ) to be mixed in concrete mixture with Portland slag cement (PSC) including hoisting, lowering, laying and compaction concrete by using vibrators, watering and curing for 28 days, centering and shuttering then after dismantling and removing debris from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required of the work etc. complete in all respect as directed by the Enginee

r-in-Charge. But excluding cost and conveyance of M.S. rods or Tor steel and binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or tor steel tying the grills and placing in proper position.- Inlet & outlet chamber

SEPTIC TANK. (50 USER) Size-(4x1.4x2) Mtr-Supplying, straightening, cutting, bending, placing in position and binding reinforcement steel work in RCC/reinforced brick works as per drawing and specification including preparation of respective bar bending schedule and binding (Binding wire to be used as per the IS code) etc. all complete as per direction of Engineer-In-Charge. Cold Twisted bars, Thermo-Mechanically-treated bars.

SEPTIC TANK. (50 USER) Size-(4x1.4x2) Mtr-First class Fly Ash Brick masonry using F.A. bricks of size 25 cm. x 12 cm. x 8 cm. having crushing strength not less than 75 kg. Per. Sqr. Cm. in cement mortar of mix (1:6) with ordinary Portland slag cement(PSC) and screened & washed sand for mortar after immersing the bricks for 6 (Six) hours in water before use in Foundation & Plinth including splays cutting, circular moulding, corbelling, chamfering and similar such type of works, watering and curing etc. including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, scaffolding, sundries, T&P required for the works etc. complete in all respect as directed by the Engineer-in-Charge.

SEPTIC TANK. (50 USER) Size-(4x1.4x2) Mtr-12mm cement plaster on internal smooth side of RCC/brick surfaces with cement mortar of mix 1:4 (1 cement : 4 fine sand) including neat cement punning & necessary scaffolding, curing etc. all complete at all floors and all heights.

SEPTIC TANK. (50 USER) Size-(4x1.4x2) Mtr-Providing 16mm. thick cement plaster in all floors at all height with cement mortar of mix (1:6) with OPC 53 grade cement finished smooth to inside smooth surface of brick masonry walls after racking out the joints including watering and curing, rounding of corners etc. complete with cost, conveyance, loading and unloading, royalties and taxes of all materials and cost of all labours, sundries, T&P and scaffolding required for the work etc. complete in all respect as desired by the Engineer in charge.

SEPTIC TANK. (50 USER) Size-(4x1.4x2) Mtr-Supplying all materials, labour, T&P and providing , fitting & fixing 100mm x100mm x100 mm SW Tee in wall including filling the recess with cement concrete (1:3:6) with 12mm size H.G chips all complete including watering, curing, conveyance of all materials to worksite, payment of royalty all complete as per specification and direction of the Engineer in charge.

SEPTIC TANK. (50 USER) Size-(4x1.4x2) Mtr-Supplying all materials, labour, T&P and making MS STEP IRON IN 20MM diameter MS steel bars & fixing into walls of man hole/septic tank duly embedded in cement concrete (1:3:6) complete as per specification and direction of the Engineer in charge.

( Pathway)-Construction of granular sub-base by providing Close graded Granular sub- base Grading-III material as per table 400-1, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density complete as per Clause 401 of MoSRT&H Specifications for Road & Bridge works (4th Revision) PAGE- 160

( Pathway)-Providing stone riprap to the slopes of earth dam and dyke with quarried and blasted granite stone boulders of size 0.30m and above including dumping on slopes filling interstices with small stones & wedges and packing surface to proper line and levels including fixing wave breakers complete with all leads & lifts complete as directed by the Engineer-in-charge. (No deduction towards voids in finished section.) (Cost of transportation to be added)

( Parking ) - Construction of granular sub-base by providing Close graded Granular sub- base Grading-III material as per table 400-1, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density complete as per Clause 401 of MoSRT&H Specifications for Road & Bridge works (4th Revision) PAGE- 160

( Parking ) -Providing stone riprap to the slopes of earth dam and dyke with quarried and blasted granite stone boulders of size 0.30m and above including dumping on slopes filling interstices with small stones & wedges and packing surface to proper line and levels including fixing wave breakers complete with all leads & lifts complete as directed by the Engineer-in-charge. (No deduction towards voids in finished section.) (Cost of transportation to be added)

Site leveling & PRR-Earth work in hard soil or gravelly soil in embankment, roads etc. within 50m initial lead and 1.5m initial lift including rough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3m in depth and as per specification approved by the Department alongwith proper compaction with P.R.R. including hire and running charges of P.R.R. (section measurement to be taken on the finished compacted section of the fill)

Site leveling & PRR-Providing granular sub-base using with morrum & sand and compacted with PRR

Site leveling & PRR-Providing WBM 75mm thick compacted thickness against the loose collection of 100mm using one cum of metal with 0.25 cum of gravel as bindage per 10sqm, and consolidation with PRR including cost, conveyance, and T&P required for the work.

Ramp- Providing granular sub-base using with moorum & sand and compacted with PRR

Ramp-Providing WBM 75mm thick compacted thickness against the loose collection of 100mm using one cum of metal with 0.25 cum of gravel as bindage per 10sqm, and consolidation with PRR including cost, conveyance, and T&P required for the work. 53mm to 22.4mm

Ramp-Providing Reinforced Cement Concrete of (1:1.5:3) with 12mm downgraded stone aggregate in foundations upto a depth of 1.5m below ground level and upto a height of 1.5m above ground level / bed level including cost and conveyance of all materials to site, and all labour charges complete as per direction of E.I.C.

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor pvc pipes conforming to ASTM-D-1785/89 (Sch-80) and pipe fittings of the following nominal bore with clamps including making good the wall, ceiling and floor all complete as per specification and direction of the Engineer in charge. Ground Floor 25mm dia PVC ASTM pipe (sch-80)

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor pvc pipes conforming to ASTM-D-1785/89 (Sch-80) and pipe fittings of the following nominal bore with clamps including making good the wall, ceiling and floor all complete as per specification and direction of the Engineer in charge. Ground Floor 32mm dia PVC ASTM pipe (sch-80)

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor pvc pipes conforming to ASTM-D-1785/89 (Sch-80) and pipe fittings of the following nominal bore with clamps including making good the wall, ceiling and floor all complete as per specification and direction of the Engineer in charge. Ground Floor 40mm dia PVC ASTM pipe (sch-80)

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor CPVC pipes conforming to IS:15778 having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00. spacing. This includes Jointing of pipes & fittings with one step CPVC solvent cement and testing of Joints all complete as per specification and direction of the Engineer in charge. Ground Floor 20mm dia CPVC pipe

PH FITTINGS (TOILET & ADMIN BLOCK)

- Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor CPVC pipes conforming to IS:15778 having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00. spacing. This includes Jointing of pipes & fittings with one step CPVC solvent cement and testing of Joints all complete as per specification and direction of the Engineer in charge. Ground Floor 25mm dia CPVC pipe

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor CPVC pipes conforming to IS:15778 having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00. spacing. This includes Jointing of pipes & fittings with one step CPVC solvent cement and testing of Joints all complete as per specification and direction of the Engineer in charge. Ground Floor 32mm dia CPVC pipe

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and cutting holes through existing brick work including making good the damages in cement mortar (1:4) for taking GI pipes and fittings/ PVC pipes and fittings etc all complete as per PH specification and direction of the Engineer in charge.- 250mm thick wall Ground Floor

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and cutting hole in R.C.C floors, roofs, etc upto 19 cm thick for passing GI pipes / PVC pipes and fittings etc and repairing the holes after insertion of pipes etc with cement concrete (1:2:4) including finishing complete so as to make it leak proof as per direction of the Engineer in charge.Ground Floor

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and cutting grooves in pucca floors and walls for taking GI/ PVC pipes and making good the damages as per the direction of the Engineer in charge.Ground Floor

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge. 15 mm dia 2 WAY BIB COCK WITH WALL FLANGE (FLR-CHR-5041N Jaquar Make)

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.- 15mm dia CP Health Faucet (ALD-CHR-577)

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge. -15 mm dia CP Long body Bib cock( FLR-CHR-5043N Jaquar make )

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.- 15mm dia CP ANGULAR STOP COCK WITH WALL FLANGE (FLR-MCH-5053N Jaquar Make )

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.- 20mm dia CP CONCEALED STOP COCK EXT HVY WTH WITH FLANGE( FLR-MCH-5083NJaquar ) Make

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.-32mm dia CP Bottle trap (Jaquar make)-ALD -CHR-769L -300x190cm

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.-Auto closing concealed urinal flush valve(Jaquar make)-PRS-CHR-077

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.-URINAL PARTITION ST.450mm(JSE-CHR-810US450X)

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.-15 mm dia CP pillar cock auto closing system(Jaquar)-PRS-CHR-031

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.-Soap Dispenser with glass bottle(ACN-CHR-1135N)

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.-CP soap Dish holder (Jaquar make)-AKP -ABR-35731P

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.-Towel Ring Round - (As Per Jaquar,Cat no.:ACN-CHR-1121BN)

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.-600mm long CP towel rail(Jaquar)-ACN-IVY-1111NM

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.-25mm dia brass or gun metal fullway valve (Shakti Make)

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.-32mm dia brass or gun metal fullway valve (Shakti Make)

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.-50mm dia brass or gun metal fullway valve (Shakti Make)

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.-15mm dia CP flange

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.-15mm dia CP extension piece

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge.-C.P. Waste 11/4"

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing CP shower with 15mm or 20mm inlet with CP shower arm including polishing all complete as per specification and direction of the Engineer in charge.15mm dia CP revolving shower With shower arm(Jaquar)OHS-CHR-1985+SHA-C

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing 10 litres capacity low level flushing cistern with a pair of cast iron or M.S brackets complete with fittings such as siphonic arrangements 15mm nominal size brass/pvc ball valve with polythene float CP brass handle, unions and couplings for connection with inlet, outlet and overflow pipes,32mm dia CP flush bend,15mm dia pvc inlet connection pipe including cutting holes and making good the same and connecting the flush bend with cistern and closet and connecting the inlet pipe with supply main etc all complete as per specification and direction of the Engineer in charge -10 litres capacity pvc low level cistern with 32mm dia CP long flush bend Slimline white (Hindware / Parryware Make)

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer’s specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge -110mm U-PVC door tee

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer’s specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge -110mm U-PVC Plain tee

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer’s specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge -110mm U-PVC door bend

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer’s specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge -110mm U-PVC plain bend

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer’s specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge -110mm dia U-PVC 'P' trap

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer’s specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge -110mm dia U-PVC Plain Shoe Bend

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with n

ails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer’s specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge -110mm dia U-PVC offset with out ear

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer’s specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge -110mm dia U-PVC cowl

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer’s specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge -125mm dia CP grating

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer’s specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge -Grab bar 300MM (Jaquar make)AHS-CHR-1501

PH FITTINGS (TOILET & ADMIN BLOCK)- -Supplying all materials, labour, T&P and cutting holes through existing brick or laterite masonry wall for taking HCI pipes and fittings including making good the damages etc. all complete as per PH specification and direction of the Engineer in charge. 250mm to 375mm thick wall

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and cutting of R.C.C roof or cornice for taking H.C.I pipes and making good the damages etc. all complete as per P.H. Specification and direction of the Engineer in charge.

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fixing the following vitreous china Wash Down Water Closet (European type W.C pan) with integral ‘P’or ‘S’ trap to the floor with wooden plug and chromium plated pedestal screws including jointing the trap with soil pipe in cement mortar (1:1), fixing plastic seat and cover for wash down water closet with chromium plated brass hinges and rubber buffers including polishing etc. all complete as per specification and direction of the Engineer in charge. European water closet with ‘S’ trap plain (Hindware)No.20079

PH FITTINGS (TOILET & ADMIN BLOCK)- Supplying all materials, labour, T&P and fixing bowl pattern urinal conforming to IS:771-part-3-1985 of the following sizes including connecting the urinal with 32mm dia pvc waste pipe 910mm long by means of white lead mixed with chopped hemp, fixing 32mm dia CP dome waste, 15mm dia CP spreader including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc all complete as per specification and direction of the Engineer in charge. Half stall urinal (Parryware / Hindware make)

15mm dia urinal spreader

32mm dia C.P. dome waste

Supplying all materials, labour, T&P and fixing wash basins with hole for pillar taps with cast iron or M S brackets painted white including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc, fixing pedestal for wash basin recessed at the back for the reception of pipes and fittings, fixing PVC waste pipe of 32mm nominal diameter for wash basin including brass check nut complete, fixing pillar taps capstan head screw down high pressure lettered ‘Hot’ and ‘Cold’ with long screws, shanks and back nuts of 15mm dia nominal bore, fixing 15mm dia PVC inlet connection pipe and making connection with pillar cocks and supply mains for wash basin, fixing 32mm dia CP brass waste, etc all complete as per specification and direction of the Engineer in charge

. Under counter basin(Hindware)10095 LARA

Supplying all materials, labour, T&P and fixing mirror of superior glass mounted on 6mm thick A.C sheet or plywood sheet and fixed to wooden plugs with CP screws and washers complete as per specification an direction of the Engineer in charge. Design mirror

Supplying all materials, labour, T&P and fixing CP soap holder complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge CP soap holder

Wiring - Recessed wirring to light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor of ISI marked Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI with 20 mm dia HMS FRLS PVC conduit ISI marked Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal 6A modular type ( flame retradant type) switch ISI marked Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) and ceiling rose ISI marked of modular type G.I box with metallic cover plate (both side) (flame retradant type) Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) of suitable size, modular box with 1.5 sq. Mm FRLS PVC insulated single core multistandard copper conductor as earth wire including all accessories and connection as per direction of Engineer -in -Charge. . All the switches & sockets should be warrantied for a replacement period of 2 years against defects with necessary test report & Warranty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials.- Group A

Wiring - Recessed wirring to light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor of ISI marked Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI with 20 mm dia HMS FRLS PVC conduit ISI marked Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal 6A modular type ( flame retradant type) switch ISI marked Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) and ceiling rose ISI marked of modular type G.I box with metallic cover plate (both side) (flame retradant type) Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) of suitable size, modular box with 1.5 sq. Mm FRLS PVC insulated single core multistandard copper conductor as earth wire including all accessories and connection as per direction of Engineer -in -Charge. . All the switches & sockets should be warrantied for a replacement period of 2 years against defects with necessary test report & Warranty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials. -Group B

Wiring - Recessed wirring to light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor of ISI marked Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI with 20 mm dia HMS FRLS PVC conduit ISI marked Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal 6A modular type ( flame retradant type) switch ISI marked Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) and ceiling rose ISI marked of modular type G.I box with metallic cover plate (both side) (flame retradant type) Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) of suitable size, modular box with 1.5 sq. Mm FRLS PVC insulated single core multistandard copper conductor as earth wire including all accessories and connection as per direction of Engineer -in -Charge. . All the switches & sockets should be warrantied for a replacement period of 2 years against defects with necessary test report & Warranty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials. -Group C

Supply and fixing of ISI marked modular type 2nos 6Amp socket with switch on suitable size of metal box and modular cover in front on surface or recess including all connection as per direction of E.I.C. All the switches & sockets should be warrantied for a replacement period of 2 years against defects with necessary test report & Warranty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials. (Make :Legrand(Myrius)/Schnider(Zencelo)//PANASONIC(VISION)

Supply and fixing of modular metal box on surface or recess with suitable size of modular cover in front including providing an fixing of ISI marked 16Amp modular plug with switch with all conection. on surface or recess including all connection as per direction of E.I.C. All the switches & sockets should be warrantied for a replacement period of 2 years against defects with necessary test report & Warranty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials. (Make :Legrand(Myrius)/Schnider(Zencelo)//PANASONIC(VISION)

Supply& fixing of Modular type 6 Amp one way switch and 6 A socket outlet with metal box and modular cover Separate Board on surface or recess including all connection as per special conditions of contract making good the damages caused complete as per the direction of Engineer-in-charge. All the switches & sockets should be warrantied for a replacement period of 2 years against defects with necessary test report & Warranty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials. (Make :Legrand(Myrius)/Schnider(Zencelo)//PANASONIC(VISION))

Submains:Recessed wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge. - 2 x 1.5 sq.mm. + 1 x 1.5 sq.mm.

Submains:Recessed wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge. - 2 x 2.5 sq.mm. + 1 x 1.5 sq.mm.

Submains:Recessed wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge. - 2 x 4.0 sq.mm. + 1 x 1.5 sq.mm.

Submains:Recessed wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge. - 4 x 6.0 sq.mm. + 2 x 4 sq.mm.

Supplying and fixing of following sizes of medium class PVC FRLS conduit ISI marked along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required as per direction of Engg.-in-Charge .Make-AKG/ BEC/ Precision/ Norpak - 20 MM

Supplying and fixing of following sizes of medium class PVC FRLS conduit ISI marked along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required as per direction of Engg.-in-Charge .Make-AKG/ BEC/ Precision/ Norpak - 25 MM

Supplying and fixing of following mentioned way, three pole/single pole and neutral, sheet steel,double door MCB distribution board, 415 volts/240 volts shall be as per IEC 61439-3,integrated door earthing system offering additional safety to the user,High quality polyurethane Gasket,the box and cover shall be

fabricated to withstand IK09,the DB should be properly pre-treated with 7 tank process and duly powder coated, phosphatized with powder coated finish, on surface/recess, complete with terminal blocks,with suitable size FR PVC insulated copper conducter up to terminal blocks, tinned copper busbar, neutral busbar, earth bar, din bar. Make-LEGRAND-Ekinox3 DB/ Siemens-Betaguard/ Schneider- Acti 9 as per direction of Engg.-in-Charge. The Distribution boards should be Replacement Warranty will be 3 years. - 4 Way(8+12) Way TPN MCB DD DB Horizontal Type as per IEC 61439-3 suitable for Flush mounting and Surface mounting with 100A Copper Bus Bar for each phase, with neutral Bus bar, Earth Bar & Cable ties for cable management, prefitted masking sheet, IP43-IK09 with metal door Warranty on DB is 3 years

Supplying and fixing of following mentioned way, three pole/single pole and neutral, sheet steel,double door MCB distribution board, 415 volts/240 volts shall be as per IEC 61439-3,integrated door earthing system offering additional safety to the user,High quality polyurethane Gasket,the box and cover shall be fabricated to withstand IK09,the DB should be properly pre-treated with 7 tank process and duly powder coated, phosphatized with powder coated finish, on surface/recess, complete with terminal blocks,with suitable size FR PVC insulated copper conducter up to terminal blocks, tinned copper busbar, neutral busbar, earth bar, din bar. Make-LEGRAND-Ekinox3 DB/ Siemens-Betaguard/ Schneider- Acti 9 as per direction of Engg.-in-Charge. The Distribution boards should be Replacement Warranty will be 3 years.- Supplying and fixing 63 Amps rating, C series,10KA breaking capacity,4P, 415 volts, MCB . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9 in the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge. .. The MCB should be Replacement Warranty will be 3 years..

Supplying and fixing of following mentioned way, three pole/single pole and neutral, sheet steel,double door MCB distribution board, 415 volts/240 volts shall be as per IEC 61439-3,integrated door earthing system offering additional safety to the user,High quality polyurethane Gasket,the box and cover shall be fabricated to withstand IK09,the DB should be properly pre-treated with 7 tank process and duly powder coated, phosphatized with powder coated finish, on surface/recess, complete with terminal blocks,with suitable size FR PVC insulated copper conducter up to terminal blocks, tinned copper busbar, neutral busbar, earth bar, din bar. Make-LEGRAND-Ekinox3 DB/ Siemens-Betaguard/ Schneider- Acti 9 as per direction of Engg.-in-Charge. The Distribution boards should be Replacement Warranty will be 3 years.- Supplying and fixing 25 Amps rating,C series,10KA breaking capacity, DP, 240 volts, RCCB 30mA . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9 in the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge. . The MCB should be Replacement Warranty will be 3 years.

Supplying and fixing of following mentioned way, three pole/single pole and neutral, sheet steel,double door MCB distribution board, 415 volts/240 volts shall be as per IEC 61439-3,integrated door earthing system offering additional safety to the user,High quality polyurethane Gasket,the box and cover shall be fabricated to withstand IK09,the DB should be properly pre-treated with 7 tank process and duly powder coated, phosphatized with powder coated finish, on surface/recess, complete with terminal blocks,with suitable size FR PVC insulated copper conducter up to terminal blocks, tinned copper busbar, neutral busbar, earth bar, din bar. Make-LEGRAND-Ekinox3 DB/ Siemens-Betaguard/ Schneider- Acti 9 as per direction of Engg.-in-Charge. The Distribution boards should be Replacement Warranty will be 3 years.-Supplying and fixing 6 amps to 32 amps rating, 240 volts, C series,10KA breaking capacity, single poles MCB of Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9. the existing MCB DB complete with connections as per direction of Engg.-in-Charge. .Warranty on MCB is 3 years.

Fittings & Fixtures-Supply of 20 watt Surface mounted indoor type BATTERN LED Luminaire with LED GLARE FREE opal diffuser , IP20 Efficency 120-130lm/w Lamp complete assembly With supply of required T&P and making connection from the suitable point outlet as per the Direction of Engineer-In-Charge

Fittings & Fixtures-Supply of 30 watt Surface SUSPENDED mounted indoor type LED LINEAR PROFILE Luminaire with LED GLARE FREE opal diffuser , IP20 Efficency 120-130lm/w Lamp complete assembly With supply of required T&P and making connection from the suitable point outlet as per the Direction of Engineer-In-Charge .

Fittings & Fixtures-SITC of Sleek LED 10 watt mirror light fitting with decorative aluminium LED batten having extruded polycarbonate housing,High optically efficient diffuser,above wash basin complete with all accessoriesetc. directly on wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required

Supply ,Installation and testing of Surface mounted indoor type 20 WATTLED Luminaire with LED GLARE FREE opal diffuser , IP20 Efficency 120-130lm/w & Functioning as per Product TDS complete assembly With supply of required T&P and making connection from the suitable point outlet as per the Direction of Engineer-In-Charge.MAKE: PANASONIC/PHILIPS/HALONIX/CROMPTON/WIPRO/HAVELLS/LT

Supply of 15 watt Extruded aluminium housing type WALL LIGHT Luminaire with LED glass diffuser in screen protction , IP65 high Efficency 120-130lm/w Lamp complete assembly With supply of required T&P and making connection from the suitable point outlet as per the Direction of Engineer-In-Charge .

Supplying, installation, of exhaust fan of heavy duty 300 mm sweep 1400 rpm 1700 cmh air delivery with louvers of exhaust fan in the existing wall, including fixing & conntection complete etc.as required and as per the direction of E.I.C..(Make-USHA (Model.Turbo HDEF 1400 RPM ISI)/Eq. model of /Havells/ ALmonrad/ Crompton

S/F of 48" Ceiling fan Alluminium Body, Copper winding, High speed ceiling fan (Make-Crompton Model-Jura, Polycab Model-Vital, Polar Model-Winpro) etc.

Supplying and fixing of Stepped type modular fan regulator on existing switch box / cover including connections etc as required.

MAIN PANEL:Incomer:63 A 4P MCCB (36 KA) with adjustable thermal setting Ics = 100% of Icu Bus bar: 4 nos. 125 A CU Busbar duly sleeved Instruments: 1 set.LED type phase indicating lamps with control fuses Outgoing : 3 Nos 63A 4P MCB. (10KA) ,3 NOS 63 DP MCB 10 KA , Instruments: 1 set.LED type phase indicating lamps with control fuses ,Instruments: 1 set.LED type phase indicating lamps with control fuses ,1 no 160/5A CT operated Digital ammeter,1nos Basic mutifunction meter SPD 4 Pole 50 KA type ( 1+11) Complete duly factory wired as per SLD and panel should have proper earth by suitable rated Aluminium flat earthing studs as per specification mentioned below duly factory wired conforming to the relevant ISS and as per special conditions of contract making good the damages caused complete as per the direction of Engineer-in-charge..MAKE - LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS- Make of MCBs- LEGRAND-DPX3/Siemens-Betaguard-Schneider-Acti-9

Supplying, laying & testing of following size of PVC insulated XLPE shethed / strip armoured aluminium / Copper conductor power cables of 1100 volt grade laid directly unground with sand cushioning, brick protection, clamped on surface of the walss / columns / existing RCC / inside masonry cable trenches / on the cable tray /throuth G.I Pipes / hume pipes / PVC pipes as the case may be, including cost of shaddles/ clamps/ markers etc but excluding the cost of G.I. Pipes / Hume pipes cpmplete with making good to the damages as required and as per direction of Engineer-in-charge. MAKE: FINOLEX/ KEI/ POLYCAB/HAVELLS/RR CABLE -3.5 core x 25 sq mm Aluminium

armoured Cable.(FOR MAIN PANEL)

Laying of one number of PVC insulated and PVC seathed / XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground in the same trench in one tier horizontal formation including excavation , sand cushining protective covering and refilling the trench etc. as required.

Supplying and making end termination with brass double compression gland and aluminium lugs for following mentioned size cable.-3.5 core x 50 sq mm brass double compression gland and aluminium lugs

Supplying,installation,testing & commissioning Of Earthing with copper earth plate 600 mm x 600mm x 3.15 mm thick ISI marked including accessories and providing masonary with cover plate having loccking arrangement and watering pipe etc as required as per direction of Engg.-in-Charge. The entire earthing system should be Replacement Warranty will be 2 years

Extra for using salt and charcoal for G.I or copper plate earth as required

Providing and fixing 25 mm X 5 mm GI strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Supply installation of 33kV 3mm thick Class-C Rubber Mat as per IS-15652 and complete as per direction of Eng-in-charge.(Size-10mx1m)

Danger Board.

Supply and fixing of first aid box with medicines complete with medicine with three years expiry date to be fixed in Electrical control panel room..

Supply and fixing of shock treatement charts duly laminated along with separate colour single line diagram laminated, to be fixed in Electrical control panel room.

ESTIMATE FOR LANDSCAPE & GARDEN DEVELOPMENT WORK -Land preparation- Site Preparation Uprooting rank vegetation and weeds by digging the area to a depth of 300 mm removing all weeds and other growth with roots by forking repeatedly ,breaking colds,rough dressing,flooding with water,uprooting fresh growth after 2 to 4 days and then dressing ,including disposal of all rubbish with all lead and lifts

ESTIMATE FOR LANDSCAPE & GARDEN DEVELOPMENT WORK --Supply of Soil-Supply and filling of good garden soil: Supply and filling of good garden soil i.e. top soil with good texture, good humus content and free from weed propagules, doob, mutha, pebbles etc., in a place as instructed by Engineer-in-Charge including transportation cost, cost of men, material, tools, tackles all complete.

ESTIMATE FOR LANDSCAPE & GARDEN DEVELOPMENT WORK - Lawn-Supplying &Turfing including transportation BroadleafGrass grass.Digging and pulverizing of soil up to a depth of 30 cm including removal of weeds, debris and disposal of waste outside the periphery of area meant for lawn making, initial grading and levelling , spreading and mixing of manures, fertilizers, organic meals and antitermite chemicals etc. in pulverized soil, dressing, levelling, landscaping the area with proper slope and making the area suitable for grassing work .

ESTIMATE FOR LANDSCAPE & GARDEN DEVELOPMENT WORK --Supply of Manure- Supply of Vermi Compost of 25 kg Bags

ESTIMATE FOR LANDSCAPE & GARDEN DEVELOPMENT WORK --Supply of Manure- Neem Cake 25 kg Bags

ESTIMATE FOR LANDSCAPE & GARDEN DEVELOPMENT WORK --Supply of ManureMustard Cake 25 kg Bags

Planting Preparation-Planting of Trees- Digging holes of size 3' x 3' x 3' and refilling the same with sweet earth mixed with manure 2 : 1 by volume flooding with water, dressing including removal of rubbish and surplus earth if any with all leads and lifts; holes 1.2m dia., 1.2m deep. Excluding cost of earth and manure.

Planting of Palms & Cycads-Digging holes of size 3' x 3' x 3' and refilling the same with sweet earth mixed with manure 4 : 1 by volume , flooding with water, dressing including removal of rubbish and surplus earth if any with all leads and lifts: '. Excluding cost of earth and manure.

Planting of Shrubs-Digging holes of size 3' x 3' x 3' and refilling the same with sweet earth mixed with manure 4 : 1 by volume , flooding with water, dressing including removal of rubbish and surplus earth if any with all leads and lifts: '. Excluding cost of earth and manure.

Planting of Hedges & Ground Covers-Prparing planting beds for ground cover planting by excavating and refilling the same with sweet earth mixed with manure 8 : 1 by volume , flooding with water, dressing including removal of rubbish and surplus earth if any with all leads and lifts: 0.3m deep. Excluding cost of earth and manure.

Supply of Trees

Supply of Palms

Supply of Ornamental Shrubs

Supply of Hedges & Ground Covers

STEEL STRUCTURE-ADMIN BLOCK-Design Providing, fabricating and erecting Structural steel members/sections in position at all levels and at all heights as specified in the drawings made out of standard MS sections conforming to IS 2062/1161/4923/12778/800. Cost to include fabricating necessary Anchor Bolts, Gusset Plates, Stiffener plates, Brackets, Bolts, Cleats, seating angles, Insert plates, chequered plate of specified thickness etc., to the required size, shape, alignment etc, as per the drawings. Cost to include welding of members using structural steel welding electrodes as per IS 814/816/817, a coat of anti corrosive Steel Guard coat primer (non flammable) to the exposed surfaces, testing as per IS 7307 (PART 1), necessary equipment, tools and tackles, staging, scaffolding required etc.,complete. Rate shall include preparation of surface, applying two coats of Zinc chromate/Phosphate primer before and after erection and two coats of first quality synthetic enamel paint of approved make of Specified Colour,after erection, sand blasting etc. complete, as directed. Rate also includes for Turn buckle (tension rod) as per the detailed drawings-Complete. (Scope shall also included detailed design of structural member connections, Preparation of GA drawings and Shop drawings, submission of all these

ROOFING-Providing and fixing Singles on 12mm thick with GI tile profile roofing The panels shall be fixed to the steel frame structure with minimum 5 mm thick self tapping GI screws of required length and nos. with minimum spacing of 300 mm c/cassembly/ the cost shall include ridge, soffit junctions & flashings as specified puff panel makers.Cost to include Approved Color As per Architect / consultant Requirement.

CUBICAL TOILET- Toilet Cubical Providing and fixing Toilet cubical made up of thermosetting resign treated high pressure ,self supporting decorative compact laminates with permanently incorporate anti-bacterial agents during manufacturing .Compact board should be resistance to water immersion through permissible increase on thickness and mass 1.35kg/cm3 and fulfilled the criteria of FSC and green guard gold certification and manufactured under EN438-2&3:2005 standard. 12mm thick compact board should be Moisture resistant, Impact resistant, termite resistant ,Scratch resistant ,Weather and climatic shock resistant. Finish of compact laminates should be suede finish which includes door, pilasters and intermediate panels finished with approved texture/shades as per IS2046 and fulfilled the criteria of fire retardant under BS-476/97

and EN438-6 th classification of BS1D0 standard. Pilaster to be supported with SS(grade316) adjustable foot and intermediate panels will attached to the wall with the help of approved SS(grade316) channels and all required hardware, made up of stainless steel as per manufacturer’s specification.. Door knob, gravity hinges, Thumb turn locksets with occupancy indicators, coat hooks with door stopper, U channel, top rail with corner connector, adjustable foot/pedestal, Rubber noise deafening tape, screw & wall plugs should be approved under the instruction of Engineer in charge. The top fitting should consist of SS. All screw will of 304 grade in SS with stain finish. All pilasters are supported by SS bottom cladding. The base of the stainless steel bottom cladding will be anchored to the floor with a clearance height upto 150 mm. Finish and colour of Toilet cubical should be approved under guidance of engineer-in-charge. Toilet cubical with standard dimension of 2100 mm(H) x 1000mm(W) x 1500mm (Depth), which includes 600mm door size width or as per drawing. Or Toilet cubical I- shape (front partition) with standard dimension of 2025mm(H) x 1000mm (W) which includes door size width or as per drawing.

CUBICAL TOILET- Toilet Cubical Providing and fixing Toilet cubical made up of thermosetting resign treated high pressure ,self supporting decorative compact laminates with permanently incorporate anti-bacterial agents during manufacturing .Compact board should be resistance to water immersion through permissible increase on thickness and mass 1.35kg/cm3 and fulfilled the criteria of FSC and green guard gold certification and manufactured under EN438-2&3:2005 standard. 12mm thick compact board should be Moisture resistant, Impact resistant, termite resistant ,Scratch resistant ,Weather and climatic shock resistant. Finish of compact laminates should be suede finish which includes door, pilasters and intermediate panels finished with approved texture/shades as per IS2046 and fulfilled the criteria of fire retardant under BS-476/97

Providing & fixing Urinal Modesty Panels made of 12 mm thick compact laminated board of approved texture/shade having standard dimension of 1200 mm Height x 450 mm Width and made as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard and should be heat, bacteria, water, chemical, scratch and impact resistant . The product should have Green Guard Certificate. Including all accessories as per approval and direction of Engineer-in-Charge .Modesty panels will be fixed to the wall at an height of 500-600mm from the floor with 304 grade SS right angle bracket, 34 grade SS Screws with satin finish & Wall Plugs. The work includes all accessories, machineries, tools etc., complete as per direction of Engineer-in- charge.

OVER HEAD TANK-Design Providing, fabricating and erecting Structural steel members/sections in position at all levels and at all heights as specified in the drawings made out of standard MS sections conforming to IS 2062/1161/4923/12778/800. Cost to include fabricating necessary Anchor Bolts, Gusset Plates, Stiffener plates, Brackets, Bolts, Cleats, seating angles, Insert plates , chequered plate of specified thickness etc., to the required size, shape, alignment etc, as per the drawings. Cost to include welding of members using structural steel welding electrodes as per IS 814/816/817, a coat of anti corrosive Steel Guard coat primer (non flammable) to the exposed surfaces, testing as per IS 7307 (PART 1), necessary equipment, tools and tackles, staging, scaffolding required etc.,complete. Rate shall include preparation of surface, applying two coats of Zinc chromate/Phosphate primer before and after erection and two coats of first quality synthetic enamel paint of approved make of Specified Colour, after erection, sand blasting etc. complete, as directed. Rate also includes for Turn buckle (tension rod) as per the detailed drawings-Complete. (Scope shall also included detailed design of structural member connections, Preparation of GA drawings and Shop drawings, submission of all these

PICNIC SPOT -1-Design Providing, fabricating and erecting Structural steel members/sections in position at all levels and at all heights as specified in the drawings made out of standard MS sections conforming to IS 2062/1161/4923/12778/800. Cost to include fabricating necessary Anchor Bolts, Gusset Plates, Stiffener plates, Brackets, Bolts, Cleats, seating angles, Insert plates , chequered plate of specified thickness etc., to the required size, shape, alignment etc, as per the drawings. Cost to include welding of members using structural steel welding electrodes as per IS 814/816/817, a coat of anti corrosive Steel Guard coat primer (non flammable) to the exposed surfaces, testing as per IS 7307 (PART 1), necessary equipments, tools and tackles, staging, scaffolding required etc.,complete.Rate shall include preparation of surface, applying two coats of Zinc chromate/Phosphate primer before and after erection and two coats of first quality synthetic enamel paint of approved make of Specified Colour, after erection, sand blasting etc. complete, as directed. Rate also includes for Turn buckle (tension rod) as per the detailed drawings-Complete. (Scope shall also included detailed design of structural member connections, Preparation of GA drawings and Shop drawings, submission of all these

ROOFING-Providing and fixing Singles on 0.50 mm thick GI tile profile roofing The panels shall be fixed to the steel frame structure with minimum 5 mm thick self tapping GI screws of required length and nos. with minimum spacing of 300 mm c/cassembly/ the cost shall include ridge, soffit junctions & flashings as specified puff panel makers.Cost to include Approved Color As per Architect / consultant Requirement.

PICNIC SPOT -2-Design Providing, fabricating and erecting Structural steel members/sections in position at all levels and at all heights as specified in the drawings made out of standard MS sections conforming to IS 2062/1161/4923/12778/800. Cost to include fabricating necessary Anchor Bolts, Gusset Plates, Stiffener plates, Brackets, Bolts, Cleats, seating angles, Insert plates , chequered plate of specified thickness etc., to the required size, shape, alignment etc, as per the drawings. Cost to include welding of members using structural steel welding electrodes as per IS 814/816/817, a coat of anti corrosive Steel Guard coat primer (non flammable) to the exposed surfaces, testing as per IS 7307 (PART 1), necessary equipment, tools and tackles, staging, scaffolding required etc.,complete.Rate shall include preparation of surface, applying two coats of Zinc chromate/Phosphate primer before and after erection and two coats of first quality synthetic enamel paint of approved make of Specified Colour,after erection, sand blasting etc. complete, as directed. Rate also includes for Turn buckle (tension rod) as per the detailed drawings-Complete. (Scope shall also included detailed design of structural member connections, Preparation of GA drawings and Shop drawings, submission of all these

Roofing-Providing and fixing Singles on 12mm thick Fibre Cement Board. The panels shall be fixed to the steel frame structure with minimum 5 mm thick self tapping GI screws of required length and nos. with minimum spacing of 300 mm c/cassembly/ the cost shall include ridge, soffit junctions & flashings as specified puff panel makers. Cost to include Approved Color As per Architect / consultant Requirement.

MAIN GATE-Design Providing, fabricating and erecting Structural steel members/sections in position at all levels and at all heights as specified in the drawings made out of standard MS sections conforming to IS 2062/1161/4923/

12778/800. Cost to include fabricating necessary Anchor Bolts, Gusset Plates, Stiffener plates, Brackets, Bolts, Cleats, seating angles, Insert plates , chequered plate of specified thickness etc., to the required size, shape, alignment etc, as per the drawings. Cost to include welding of members using structural steel welding electrodes as per IS 814/816/817, a coat of anti corrosive Steel Guard coat primer (non flammable) to the exposed surfaces, testing as per IS 7307 (PART 1), necessary equipments, tools and tackles, staging, scaffolding required etc.,complete.Rate shall include preparation of surface, applying two coats of Zinc chromate/Phosphate primer before and after erection and two coats of first quality synthetic enamel paint of approved make of Specified Colour,after erection, sand blasting etc. complete, as directed. Rate also includes for Turn buckle (tension rod) as per the detailed drawings-Complete. (Scope shall also included detailed design of structural member connections, Preparation of GA drawings and Shop drawings, submission of all these

ROOFING-Providing and fixing Singles on 0.50 mm thick GI tile profile roofing The panels shall be fixed to the steel frame structure with minimum 5 mm thick self tapping GI screws of required length and nos. with minimum spacing of 300 mm c/cassembly/ the cost shall include ridge, soffit junctions & flashings as specified puff panel makers.Cost to include Approved Color As per Architect / consultant Requirement.

VENDING ZONE-Design Providing, fabricating and erecting Structural steel members/sections in position at all levels and at all heights as specified in the drawings made out of standard MS sections conforming to IS 2062/1161/4923/12778/800. Cost to include fabricating necessary Anchor Bolts, Gusset Plates, Stiffener plates, Brackets, Bolts, Cleats, seating angles, Insert plates , chequered plate of specified thickness etc., to the required size, shape, alignment etc, as per the drawings. Cost to include welding of members using structural steel welding electrodes as per IS 814/816/817, a coat of anti corrosive Steel Guard coat primer (non flammable) to the exposed surfaces, testing as per IS 7307 (PART 1), necessary equipment, tools and tackles, staging, scaffolding required etc., complete.Rate shall include preparation of surface, applying two coats of Zinc chromate/Phosphate primer before and after erection and two coats of first quality synthetic enamel paint of approved make of Specified Colour,after erection, sand blasting etc. complete, as directed. Rate also includes for Turn buckle (tension rod) as per the detailed drawings-Complete. (Scope shall also included detailed design of structural member connections, Preparation of GA drawings and Shop drawings, submission of all these

Roofing-Providing and fixing Singles on 0.50 mm thick GI tile profile roofing The panels shall be fixed to the steel frame structure with minimum 5 mm thick self tapping GI screws of required length and nos. with minimum spacing of 300 mm c/cassembly/ the cost shall include ridge, soffit junctions & flashings as specified puff panel makers.Cost to include Approved Color As per Architect / consultant Requirement.

TOILET BLOCK-Design Providing, fabricating and erecting Structural steel members/sections in position at all levels and at all heights as specified in the drawings made out of standard MS sections conforming to IS 2062/1161/4923/12778/800. Cost to include fabricating necessary Anchor Bolts, Gusset Plates, Stiffener plates, Brackets, Bolts, Cleats, seating angles, Insert plates , chequered plate of specified thickness etc., to the required size, shape, alignment etc, as per the drawings. Cost to include welding of members using structural steel welding electrodes as per IS 814/816/817, a coat of anti corrosive Steel Guard coat primer (non flammable) to the exposed surfaces, testing as per IS 7307 (PART 1), necessary equipment, tools and tackles, staging, scaffolding required etc.,complete. Rate shall include preparation of surface, applying two coats of Zinc chromate/Phosphate primer before and after erection and two coats of first quality synthetic enamel paint of approved make of Specified Colour,after erection, sand blasting etc. complete, as directed. Rate also includes for Turn buckle (tension rod) as per the detailed drawings-Complete. (Scope shall also included detailed design of structural member connections, Preparation of GA drawings and Shop drawings, submission of all these

BAMBOO WORK-ADMIN BLOCK CLADDING- Fiber Cement Sandwich Panel- Prefabricated Fibre Cement Sandwich Panels shall be made of two fibre reinforced cement facing boards on either sides of a lightweight concrete core. These fiber cement boards shall be of thickness upto 5 mm and conforms to IS 14862:2000 (Type - A). The core shall composed of Portland cement and a mix of silacaceous & micaceous material. These panels shall have unique tongue and Groove locking arrangements for jointing. • There shall be 2 types of Fibre Cement Sandwich Panels, which will be used depending upon the finish required and type of application of wall, namely Recess Edge (RE - 1 mm x 30 mm recess area along the height on tongue & groove location to accommodate the jointing tape) and Square Edge . It is Certified by CPWD DSR, BMTPC, IGBC and GRIHA. • Size - 600 mm x 2400/2700/3000 mm x 75 mm (W X H X T) • Recyclable material such as Fly Ash as a raw material is used in panel manufacturing makes the product Eco Friendly & Green Building Material. • Panels are having excellent fire, water and termite resistance properties. Panels can withstand adverse weather conditions.

OVER HEAD TANK-Design Providing, fabricating and erecting Structural steel members/sections in position at all levels and at all heights as specified in the drawings made out of standard MS sections conforming to IS 2062/1161/4923/12778/800. Cost to include fabricating necessary Anchor Bolts, Gusset Plates, Stiffener plates, Brackets, Bolts, Cleats, seating angles, Insert plates , chequered plate of specified thickness etc., to the required size, shape, alignment etc, as per the drawings. Cost to include welding of members using structural steel welding electrodes as per IS 814/816/817, a coat of anti corrosive Steel Guard coat primer (non flammable) to the exposed surfaces, testing as per IS 7307 (PART 1), necessary equipment, tools and tackles, staging, scaffolding required etc.,complete. Rate shall include preparation of surface, applying two coats of Zinc chromate/Phosphate primer before and after erection and two coats of first quality synthetic enamel paint of approved make of Specified Colour, after erection, sand blasting etc. complete, as directed. Rate also includes for Turn buckle (tension rod) as per the detailed drawings-Complete. (Scope shall also included detailed design of structural member connections, Preparation of GA drawings and Shop drawings, submission of all these

PICNIC SPOT -1-Design Providing, fabricating and erecting Structural steel members/sections in position at all levels and at all heights as specified in the drawings made out of standard MS sections conforming to IS 2062/1161/4923/12778/800. Cost to include fabricating necessary Anchor Bolts, Gusset Plates, Stiffener plates, Brackets, Bolts, Cleats, seating angles, Insert plates , chequered plate of specified thickness etc., to the required size, shape, alignment etc, as per the drawings. Cost to include welding of members using structural steel welding electrodes as per IS 814/816/817, a coat of anti corrosive Steel Guard coat primer (non flammable) to the exposed surfaces, testing as per IS 7307 (PART 1), necessary equipments, tools and tackles, staging, scaffolding required etc.,complete.Rate shall include preparation of surface, applying two coats of Zinc chromate/Phosphate primer before and after erection and two coats of first quality synthetic enamel paint of approved make of Specified Colour, after erection, sand blasting etc. complete, as directed. Rate also includes for Turn buckle (tension rod) as per the detailed drawings-Complete. (Scope shall also included detailed design of structural member connections, Preparation of GA drawings and Shop drawings, submission of all these

ROOFING-Providing and fixing Singles on 0.50 mm thick GI tile profile roofing The panels shall be fixed to the steel frame structure with minimum 5 mm thick self tapping GI screws of required length and nos. with minimum spacing of 300 mm c/cassembly/ the cost shall include ridge, soffit junctions & flashings as specified puff panel makers.Cost to include Approved Color As per Architect / consultant Requirement.

PICNIC SPOT -2-Design Providing, fabricating and erecting Structural steel members/sections in position at all levels and at all heights as specified in the drawings made out of standard MS sections conforming to IS 2062/1161/4923/12778/800. Cost to include fabricating necessary Anchor Bolts, Gusset Plates, Stiffener plates, Brackets, Bolts, Cleats, seating angles, Insert plates , chequered plate of specified thickness etc., to the required size, shape, alignment etc, as per the drawings. Cost to include welding of members using structural steel welding electrodes as per IS 814/816/817, a coat of anti corrosive Steel Guard coat primer (non flammable) to the exposed surfaces, testing as per IS 7307 (PART 1), necessary equipment, tools and tackles, staging, scaffolding required etc.,complete.Rate shall include preparation of surface, applying two coats of Zinc chromate/Phosphate primer before and after erection and two coats of first quality synthetic enamel paint of approved make of Specified Colour,after erection, sand blasting etc. complete, as directed. Rate also includes for Turn buckle (tension rod) as per the detailed drawings-Complete. (Scope shall also included detailed design of structural member connections, Preparation of GA drawings and Shop drawings, submission of all these

Bamboo Matboard- Bamboo mat board is made of two or more bamboo mats bonded with an adhesive. The mat used is made by weaving thin, uniform strips of bamboo, In the present scenario, where availability of conventional timber has been reduced to considerable extent, the bamboo mat board is expected to find extensive use in future A board made of two or more bamboo mats bonded with an adhesive. Adhesive for bonding bamboo mat board shall be of phenolic type conforming to BWR type specified in IS 818: 1974. Adhesive coated mats shall be allowed sufficient length of open assembly time and/or passed through a band dryer at elevated temperature in the range of 80°C to 90°C to bring down the moisture content of adhesive coated mats to 8 to 12percent. After hot pressing the finished bamboo mat board shall be conditioned to a moisture content not less than 5 percent and not more than 15 percent. For bamboo mat board manufactured by applying the resin by passing the mats through mechanical glue spreader, the manufactured boards shall be treated with non-leachable type preservatives such as Copper-Chrome Arsenic ( CCA ), Copper-Chrome-Boron ( CeO) or Acid-Copper-Chrome ( ACe) as per 5.2.2.3 of IS 5539 : 1969. For bamboo mat board manufactured by applying the resin by soaking method, preservative treatment shall be done by incorporating the preservatives like boron (octaborate or tetraborate ) into the resin before soaking the mats. The preservative becomes non-leachable during hot pressing.

Whole Bamboo- Bamboo treatment with Borax and Boric Acid. Borax or sodium borate is a soft, colorless, powdery mineral that dissolves easily in water. It is a natural insect repellent an

d preservative. Treated bamboo is incredibly versatile, finding uses in construction, furniture, textiles, and even food and medicine. It's often treated to enhance its durability and resistance to insects and decay, making it suitable for a wide range of applications.

Rubber Shingles - Rubber shingles, offer a durable and environmentally friendly roofing option. They are known for their impact resistance (especially Class 4 rating), long lifespan, and ability to withstand extreme temperatures and high winds. Roofing shingles are a construction material for residential roofing application that is used on roof slopes of 12° or greater. It is the smartest solution for a complex or intricate roof design. Bitumen shingles do not fade; they are resistant to harmful environmental impacts, decay, corrosion, fire damage, and, what is very important, they perform well in extreme temperatures. Roofing shingles by TECHNONICOL fully comply with EN 544. This European standard for bitumen shingles is known for its strict requirements for the minimum mass of bitumen in products (1300 g/m2 – for single-layer roofing shingles and 1500 g/m2 – for multilayer ones). Our commitment to quality control, best raw materials and up-to-date technology guarantees years of superior performance to customers. Algae resistance for 10 years officially guaranteed for some collections. Basalt granules of diverse shades add depth and dimension to shingles texture to get a statement-making roofing. Thanks to weather resistant mineral surface, the color will not fade over time. Multilayer coating and its specific components make extremely quiet roofing. The noise of rain, wind or hail hitting the roof will not torture you. Enjoy peace and quiet in your house! Roofing shingles weight is just 12.5 kg/m2 (COUNTRY collection) compared with 40 kg/m2 weight of ceramic tiles. It results in the lower load and greater safety.

Cement Board (12mm)- Cement board is a auto clave cellulose fiber cement flat boar and is 100% asbestos free board with a smooth surface and square edges. It is a green board which use fly ash as pozzolonic material with 53 grade OP cement as per IS:12269-1987 and reinforce by fiber cellulose pulp in manufacture of flat sheets. It possess superior thermal insulation properties, thus helps save on air conditioning and heating bills which further reduced the carbon footprints.