Up-gradation of Sub Health Center to AB-HWC (Health Wellness Center) at village Rajli in District Hisar

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5m, as directed by Engineer-in-charge. (HSR 4.12.1) All kinds of soil

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. (HSR 5.7.4) In cement mortar

Demolishing brick tile covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. (HSR 5.14)

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead: (HSR 5.29.1) Of area 3 sq. metres and below

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. (HSR 5.45)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: (HSR 6.1.6) 1 :4: 8 ( 1 Cement : 4 coarse sand (zone-Ill) : 8 graded stone aggregate 40 mm nominal size)

Brick work with common burnt clay non-modular bricks of class designation 7 .5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : (HSR 7.22.1) Cement mortar 1:4 (1 cement: 4 coarse sand)

10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1: 1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1: 3 (1cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: (HSR 9.11.1) With common burnt clay non-modular brick tile of class designation 1O

Providing gola 75x75 mm in cement concrete 1: 2:4 (1 cement : 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cementmortar 1 :3 (1 cement : 3 fine sand) as per standard design :(HSR 9.17.1) In 75x75 mm deep chase

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% andconforming to IS: 15622, of approved make, in all colours and shades, laid on20mm thick cement mortar 1 :4 (1 cement : 4 coarse sand), jointing with greycement slurry @ 3.3 kg/ sqm including grouting the joints with white cementand matching pigments etc., complete. (HSR 10.63.2) Size of Tile 600x600 mm

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1 :4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. (HSR 10.60)

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1 :4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. (HSR 10.62)

12 mm cement plaster of mix: (HSR 11.5.3) 1 :4 (1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : (HSR 11.6.1) 1 :4 (1 cement: 4 fine sand)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: (HSR 11.67.1) Water thinnable cement primer

Distempering with 1st quality acrylic distemper, having voe (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. (HSR 11.66.2) Two coats

Providing and fi xing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :(HSR12.78.2) 200x10 mm

Providing and fixing aluminium sliding door bolts, ISi marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : (HSR 12.98.2) 250x16 mm

DOOR/WINDOW FRAMES AND SHUTTERS Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) :(HSR12.157.1.2) Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) (HSR 12.157.2.2) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. (HSR 12.158.2) Pre-laminated particle board with decorative lamination on both

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): (HSR 12.159.1) With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge. (HSR 12.163.2) Powder coated minimum thickness 50 micron aluminium tubular handle bar

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. (HSR 13.27)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level:(HSR 6.1.8)1:5:10 (1 cement : 5 fine sand : 10 graded stone cum aggregate 40 mm nominal size)

Brick work with common burnt clay non-modular bricks of class designation 7.5 in foundation and plinth in: ( HSR 7.21.1) Cement mortar 1:4 (1 cement: 4 coarse sand)

Providing and laying damp-proof course with cement concrete 1 :2:4 (1 cement : 2 coarse sand (zone-Ill): 4 graded stone aggregate 12.5mm nominal size) ( HSR6.8.3) 25 mm thick

15 mm cement plaster on rough side of single or half brick wall of mix: (HSR 11.9.1) 1 :4 (1 cement: 4 coarse sand)

Pointing on tile brick work with cement mortar 1 :3 (1 cement : 3 fine sand): (HSR 11.26.1) Flush/ Ruled/ Struck or weathered pointing

Recovery Item: Bidders have to quote rates for recovery items at least or more than reserve price. The rates quoted against recovery will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Materials obtained from dismantling of structure have been calculated taking assumption of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) on approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. The reserve price is as under:- (i) Bricks tiles @ 5.00/- Each

(ii) Bricks bats @ Rs.500/- per cum

(iii) Door, @ Rs. 1000/- Each

(iv) Window @ Rs.1500/- Each

(v) Ventilator @ Rs. 600/- Each

(vi) Bricks @ Rs. 5.00 /- Each

(vii) Bricks bats @ Rs. 500/- per cum Note: All quantities of the above materials have been worked out on the basis of theoretical quantities. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price.

Sh Pardeep Kumar S/o Sh Inder Singh

K.D. Sons

P.G. Contractor

THE KHEDAR COOPERATIVE MULTIPURPOSE SOCIETY LTD

PRADEEP KUMAR

Rajesh S/o Sh. Gyani Ram