Development of premises of Mahakali Temple At Chandrapur Tahsil Chandrapur District Chandrapur.(Including Electric Work)

Amount

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) by Mechanical means

Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 metres beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth/murum, ramming ,watering including shoring and strutting etc. complete. (Lift from 1.5m To 3.0 m.) By Mechanical Means

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on bond paper.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diametre about 30 -60 cm deep at 15 cm c/c as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on bond paper.

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete.

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete.

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.),with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granit /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork ,cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

First Floor

Second Floor

Thrid Floor

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

First Floor

Second Floor

Thrid Floor

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

First Floor

Second Floor

Thrid Floor

Providing and laying Cast in situ/Ready Mixcement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

First Floor

Second Floor

Thrid Floor

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap / quartzite /granite /gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

First Floor

Second Floor

Thrid Floor

Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.(For All Floors)

Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete.

Providing Autoclaved Aerated Concrete Block masonary of Ecolite or equivalent make conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972)

First Floor

Second Floor

Thrid Floor

Providing Autoclaved Aerated Concrete Block masonary of Ecolite or equivalent make conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972)

First Floor

Second Floor

Thrid Floor

Providing and laying jointless Polydee-LM, a highly flexible elastometric coating for RCC / cementitious surface for terrace waterproofing on B.B. Coba / R.C.C, after application of TP-42 Primer on perfectly clean surface (free from loose dust and foreign matter) application of 1st coat of Polydee-LM @ 700 gms/sqm and applying 2nd coat of Polydee-LM @ 700 gms/sqm and finishing the same with sprinkling the AG-10 granules on the wet coating. (After finishing covering the treatment with 25mm cement plaster for protection with fibrillated 6mm Plyplast fibre @ 125 gms/sqm to be paid in separate item.) covering 7 years guarantee on Court Fee Stamp Paper of Rs. 100/- etc. complete.

First Floor

Providing water proof bedding for flooring of Bath and WC 25 mm thick in C.M. 1:3 including using approved water proofing compound in specified proportion as per manufacturers specifications for per bag of cement including leveling, curing and covering 10 years guarantee on court fee stamp paper of Rs.500/- including ponding test etc. complete.

First Floor

Second Floor

Thrid Floor

Providing and fixing 20 to 25 mm thick rough shahabad box type waterproofing for basement or underground floor on a base of Cement concrete 1:3:6, including sub base of 2.50 centimeter thick Cement mortar 1:3 with conceal, secrete (RMW), Algae proof or other alike waterproofing liquids, raking of joints upto 35 mm depth, filling the joints with 6 mm size crushed metal, hand grouting with cement slurry, curing and cleaning, with 7 years guarantee on court fee stamp of Rs. 100/- with ponding test etc complete. (excluding Cement concrete 1:3:6 base concrete )

Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1kg/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 kg/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 kg/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete.

First Floor

Second Floor

Thrid Floor

Providing internal cement plaster 6 mm thick in a single coat in cement mortar 1:3 without neeru finish to concrete surface in all positions including scaffolding and curing etc. complete.

First Floor

Second Floor

Thrid Floor

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

First Floor

Second Floor

Thrid Floor

Providing and applying gypsum plaster ( with Gypsum material of Gypsum India / Mega Sign or equivalent make ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete.

First Floor

Second Floor

Thrid Floor

Providing and applying plastic emulsion paint of approved quality, colour and shade to new surface in three coats including scaffolding, preparing the surface. (excluding primer coat) etc. complete.

First Floor

Second Floor

Thrid Floor

Providing and applying Royale Luxury Emulsion of Asian / Berger / Nerolac / Dulex Paints or equivalent make on internal wall surface as detailed below Scrapping for surface with emery paper and wipe clean for area. Applying Asian / Berger / Nerolac / Dulex Paints or equivalent wall primer with brush by adding mineral turpentine oil by 8 to 10 % or water by 15 to 20% allowing to dry for 6 to 8 hoursAfter applying Asian / Berger / Nerolac / Dulex Paints or equivalent acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 50% or 65 to 70% by role Applying paints Royale luxury emulsion 2nd coat with brush with water content 40 to 45 % or 65 to 70 % by roller. (With prior approval of S.E.)

First Floor

Second Floor

Thrid Floor

Providing and laying polished hand cut Kotah Stone flooring 25mm to 30mm thick and 45cm to 55cm wide in plain/diamond pattern on a bed of 1:6 C.M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning complete.

Providing and laying machine cut machine polished machine cut Kota stone slabs 20 to 25 mm thick for treads and risers of steps and staircases, with rounded nosing for the treads on a bed of 1:4 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete.

First Floor

Second Floor

Third Floor

Providing sills of required material 20mm to 25mm thick, on a bed of cement mortar 1:4 including cement float, filling joints with neat cement slurry, curing, polishing, moulding edges, cleaning complete. a) Marble other than white makrana

Providing sills of required material 20mm to 25mm thick, on a bed of cement mortar 1:4 including cement float, filling joints with neat cement slurry, curing, polishing, rounding edges, cleaning complete. b) Granite

First Floor

Second Floor

Third Floor

Providing and laying ceramic tiles having size 30 cm. x 45 cm. confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.

Providing and laying ceramic tiles having size 30 cm. x 60 cm. confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.

First Floor

Second Floor

Third Floor

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete.

First Floor

Second Floor

Third Floor

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.

First Floor

Second Floor

Third Floor

Providing and fixing machine cut mirror polished 18 mm to 20 mm thick telephone black granite / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone partition with full moulding the edges etc. complete . Both side polish

First Floor

Second Floor

Third Floor

Providing and preparing kitchen otta up to 75 cm width,made up from 30 mm thick and 75 cm high vertical support for kadppa at 1 m. c/c of 25 mm thick both side polished kadappa middle shelf and bottom of 20 mm thick one side polished kadappa with facia patti of 20 x 50 mm kadappa including all material labour cutting fixing with cement mortar and araldite curing polished and cleaning etc. complete.

First Floor

Second Floor

Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. a) Flooring

First Floor

Second Floor

Third Floor

Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete

First Floor

Second Floor

Third Floor

Providing and laying vitrified matt fininsh tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete. a) Flooring

First Floor

Second Floor

Third Floor

Providing and laying vitrified matt finish tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete.

First Floor

Providing and laying vitrified stone effect finish tiles having size 590 to 605 mm x 590 to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete a) Flooring

First Floor

Second Floor

Third Floor

Providing and laying vitrified stone effect finish tiles having size 590 to 605 mm x 590 to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including required position laid on a bed of 1:4 cement mortarincluding neat cement float, filling joints, curign and cleaning etc. complete.

First Floor

Second Floor

Third Floor

Providing leather finished polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matt finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete.

First Floor

Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete.

First Floor

Second Floor

Third Floor

Providing and fixing frame work of galvanised iron for suspended false ceiling which includes galvanised iron perimeter channels of size 27 mm and 0.5 mm thick having one flange of 20 mm and another of 30 mm along with perimeter of the ceiling, fixing in brick wall / partition with the help of rawal plugs and screws, suspending galvenised iron intermediate channels of size 45 mm and 0.9 mm thick with two flanges of 15 mm each from the soffit at 1200 mm centers with steel galvanised iron hanger of width 25 mm x 0.5 mm fasteners, ceiling section of 0.5 mm thickness having curved wedge of 51.5 mm and two flanges of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate channel at 450 mm centers, 12.5 mm dry walls screws at 230 mm centers; fixing screws mechanically either with screw driver or drilling machine with suitable attachment etc. complete.

First Floor

Second Floor

Third Floor

Providing and fixing false ceiling of 10 to 12 mm thick decorative boards of fibrous plaster of paris including scaffolding if necessary all architectural work like mouldings, cornices, coves, domes, cups as per detailed drawings and three coats of spray painting to boards etc. complete. (excluding frame work, runners and mild steel suspenders).

First Floor

Second Floor

Third Floor

Providing and fixing frame with / without ventilator of size as specified with Country non teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete.

First Floor

Second Floor

Third Floor

Providing and fixing solid core flush door shutter in single leaf 32 mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete.

First Floor

Second Floor

Third Floor

Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 mm at weight 0.547 kg/Rmt. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 kg/Rmt. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 kg/Rmt. The shutter should be of bearing bottom40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. And handle section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. and top section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With colour Anodising with box.

First Floor

Second Floor

Third Floor

Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 kg/Rmt. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 kg/Rmt.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section 40 x 18 x 1.25 mm at weight o.417 kg/Rmt. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour Anodising with box

First Floor

Second Floor

Third Floor

Supplying and fixing in position -------------- Aluminium four track sliding windows with outer frame made from section of over all size 122 mm x 45 mm, bottom section with drain section track weighing 1.83 kg per metre and top and side section of size 122x 31.75 mm weighing 1.15 kg per running metre with shutter sections made of 18 mm x 40 mm size having average weight of 0.6 kg per running metre (or as required size) with change in proportionate weight, with 6 mm float glass in three equal panels and alluminium coated stainless steel mosquito net in one (2/3 of opening) panel fixed with new neoprene gasket, shutters to be provided with nylon encased stainless steel rollers, necessary locks and handles complete. with Colour anodized

First Floor

Second Floor

Third Floor

Providing and fixing fiber glass reinforced polyster door shutter 35 mm thick as per IS 14856 (2000) (Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc complete.

First Floor

Second Floor

Third Floor

Providing and fixing in position anodised (as per IS 1868/1982) Aluminium fixed staggered ( Z Type) Ventilator with aluminium rectangular pipe 63 mm x 38.10 mm x 1.22 mm at weight 0.650 Kg/Rmt, Aluminium angle of size 15 mm x 15 mm x 1 mm,aluminium channel of 9 mm sizes, S.S.mosquito net of 304 Grade,4 mm thick float glass per detailed drawing and as directed by Engineer in charge

First Floor

Second Floor

Third Floor

Fire Door 45mm 1HR FRL (60/60) 3 Criteria - INTEGRITY / INSULATION/ STABILITY WOODEN DOOR - Fire Door Tested in accordance to IS: 3614 Part 2. a) Door Frame: Supplying 'Tufwud' brand frames for Fire resistant door shutters 1st class Malaysian Hardwood Frame densified (810 kg/cum) and pressure treated with fire retardant chemicals in vacuum impregnation vessel under 160 psi pressure as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 of section 120 X 60 mm spray quoted with 2 coats of intumescent paint of minimum 200 micron, with single row of Brush- Type ASTROFLAME intumescent strip of size 10mm x 4mm affixed in the slit of the Frame for fire and smoke sealing, etc. complete.

First Floor

Second Floor

Third Floor

Providing and fixing in position at all heights GRC bracket/ Corbel Final Type-1 (144 x 300 mm) as per detailed design and drawings with all finishing treatment required as per specification of Engineer in charge etc. complete Including all transportation charges.

Providing and laying Cast in situ/Ready Mix Self Compcting cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. work in R.C.C. Cornices etc. as per detailed designs and drawing or as directed including M.S. / FRP centering formwork at top and bottom, installing,removing with all necessary supportings, nail, binding wire, skilled and unskilled labour etc. including all lifts complete.

Providing and laying self compacting Ready Mix Concrete of M30 grade as per IS 456-2000 for RCC Cornices as per approved structural design including providing and mixing required admixture for self compacting concrete (Super Plasticizer- FOSROC AURAMIX 300 and viscosity Modifiying agent (VMA) FOSROC AURAMIX V100) in recommanded proportions as per IS 9103 & reinforcement and as approved by Engineer in charge, for achieving 150-200 mm slump, for RCC members having thickness, required depth and lengths as per bailing out water up to depth of 3.5 m, curing etc., but excluding reinforcement and inserts. (Rate includes all inputs of labour, material and T & P, cost of handelling, lifting and placing in position concrete etc.)Course aggregate to br used for this purpose shall be 12.5 mm down, complete as directed by Engineer in Charge.

Providing and fixing M.S. / FRP centering formwork at inner and outer side for Columns etc. as per detailed designs and drawing or as directed including installing,removing with all necessary supportings, nail, binding wire, skilled and unskilled labour etc. including all lifts complete.

Providing and laying self compacting Ready Mix Concrete of M30 grade as per IS 456-2000 for RCC Columns as per approved structural design including providing and mixing required admixture for self compacting concrete (Super Plasticizer- FOSROC AURAMIX 300 and viscosity Modifiying agent (VMA) FOSROC AURAMIX V100) in recommanded proportions as per IS 9103 & reinforcement and as approved by Engineer in charge, for achieving 150-200 mm slump, for RCC members having thickness, required depth and lengths as per bailing out water up to depth of 3.5 m, curing etc., but excluding reinforcement and inserts. (Rate includes all inputs of labour, material and T & P, cost of handelling, lifting and placing in position concrete etc.)Course aggregate to br used for this purpose shall be 12.5 mm down, complete as directed by Engineer in Charge.

Providing and fixing M.S. / FRP centering formwork at top and bottom for Domes etc. as per detailed designs and drawing or as directed including installing,removing with all necessary supportings, nail, binding wire, skilled and unskilled labour etc. including all lifts complete.

Providing and laying self compacting Ready Mix Concrete of M30 grade as per IS 456-2000 for RCC Domes as per approved structural design including providing and mixing required admixture for self compacting concrete (Super Plasticizer- FOSROC AURAMIX 300 and viscosity Modifiying agent (VMA) FOSROC AURAMIX V100) in recommanded proportions as per IS 9103 & reinforcement and as approved by Engineer in charge, for achieving 150-200 mm slump, for RCC members having thickness, required depth and lengths as per bailing out water up to depth of 3.5 m, curing etc., but excluding reinforcement and inserts. (Rate includes all inputs of labour, material and T & P, cost of handelling, lifting and placing in position concrete etc.)Course aggregate to br used for this purpose shall be 12.5 mm down, complete as directed by Engineer in Charge.All Floor Level Qty.

Providing and fixing in position at all heights Gypsum Arches as per detailed design and drawings with all finishing treatment required as per specification of Engineer in charge etc. complete Including all transportation charges.

Providing and laying Vetrified Tiles type RAK/ Kajaria/ Nitco/ Asian or equivalent make having size 200 x 200 mm of 8 to 10 mm thickness and conforming to IS 15622-2006 (group Bla) of approved make, shade and pattern for Flooring in required position laid on bed of 1:4 cement mortar including neat float, filling joints, curing and cleaning etc. complete.a. Skirting

Providing and fixing in position at all heights Gypsum Cornice as per detailed design and drawings with all finishing treatment required as per specification of Engineer in charge etc. complete Including all transportation charges.

Providing and fixing in position at all heights Gypsum Designer Ceiling as per detailed design and drawings with all finishing treatment required as per specification of Engineer in charge etc. complete Including all transportation charges.

Providing and fixing Orissa type white glazed earthenware water closet pan of size 260mm x 440mm x 580mm with approved make Slim wall hung cistern with installation kit including S or P trap with cast iron soil and vent pipe upto outside face of the wall 1:2:4 brick bat lime concrete bedding without flushing tank and its accessories etc.complete

First Floor

Second Floor

Third Floor

Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge.

First Floor

Second Floor

Third Floor

Providing and fixing C.P. Angular stop clock with wall flange of approved make continental including necessary sockets/union nut etc. complete.

First Floor

Second Floor

Third Floor

Providing and fixing white european type wall-hung pan, of size 350mm x 355mm x 570 mm concealed flush tank with floormounting frame installing kit and drain pipe connection set for wall hung WC, with approved make square control plates including soil pipe, vent pipe upto the outside face of wall, 100mm dia C.I. plug bend inlet pipe all fittings,cutting & making good walls, floors etc. complete.Ground Floor

First Floor

Second Floor

Third Floor

Providing and fixing C.P. a 2-Way BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge.Ground Floor

First Floor

Second Floor

Third Floor

Providing and fixing Hand shower (health faucet) with 8mm dia. 1m long flexible tube having wall hook with approved make including necessary sockets/ union nut etc. complete as directed by Engineer incharge. Ground Floor

First Floor

Second Floor

Third Floor

Providing and fixing wall hung white wash basin of size 350x450x165mm with approved make pillar cock, C.P. Angular stop cock long thread approved make continental including SS bottle trap of approved make having necessary pipe connection up to the outside face of the wall etc complete as directed by Engineer in charge.Ground Floor

Second Floor

Third Floor

providing and fixing oval type under counter wash hand basin of 16inch x 22 inch size and of special colour shade having telephonic black/ coloured granite of 180 mm thick stone black kadappa framework including chromium plated coupling bottle - Trap using CERA company or equivalent oval typa wash basin model no 3448 as per detailed drawing or as directed by engg incharge etc complete. (Counter size 1.20 m x 0.60 m )Ground Floor

First Floor

Second Floor

Third Floor

Providing and fixing C.P. pillar cock long neck with aerator of approved make including necessary sockets/union nut etc. complete.Second Floor

Third Floor

Providing and fixing Autoclosing pillar cock of pressmatic tap of approved make or equivalent including all fixtures, fittings etc.complete. Ground Floor

First Floor

Providing and fixing Shower Head, with shower arm of approved make mixer of including all necessary pipe fittings and connections etc. complete as directed by Engineer in charge.Ground Floor

Second Floor

Third Floor

Providing and fixing white glazed urinal of series with Pressmatic auto closing valve of having 32mm diameter P.V.C. flush pipe with fitting and flushing of approved make and arrangement including lead soil pipe, lead trap & soil pipe connection upto the outside face of wall etc.complete as directed by Engineer in charge, Ground Floor

First Floor

Second Floor

Third Floor

Providing and fixind Robe Hook of approved make of including all necessary fittings and connections etc. complete as directed by Engineer in charge.Ground Floor

First Floor

Second Floor

Third Floor

Providing and fixing Grab Rail of approved make of including all necessary fittings and connections etc. complete as directed by Engineer in charge. Ground Floor

Second Floor

Third Floor

Providing and fixing Grab Bar of approved make of including all necessary fittings and connections etc. complete as directed by Engineer in charge.

First Floor

Second Floor

Third Floor

Providing and fixing Cockroach Trap of approved make of including all necessary fittings and connections etc. complete as directed by Engineer in charge.

First Floor

Second Floor

Third Floor

Providing and fixing Floor Drain Grating of approved make of including all necessary fittings and connections etc. complete as directed by Engineer in charge.

First Floor

Second Floor

Third Floor

Providing and fixing Soap Dispenser of approved make of including all necessary fittings and connections etc. complete as directed by Engineer in charge.

First Floor

Second Floor

Third Floor

Providing and fixing Glass shelf 125 mm wide and 600 mm long with necessary chromium plated brackets providingT.W.gutties etc. Complete

Second Floor

Third Floor

Providing and fixing chromium plated towel rod 16 mm dia and 75 cm. in length including all accessories complete.

Second Floor

Third Floor

Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Second Floor

Third Floor

Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

First Floor

Second Floor

Third Floor

Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

First Floor

Second Floor

Third Floor

Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc.

First Floor

Second Floor

Third Floor

Providing and fixing on walls /ceiling/ floor 40 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc.

First Floor

Third Floor

Providing and fixing on walls/ ceiling/ floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.

First Floor

Third Floor

Providing and fixing on walls/ ceiling/ floors, 80 mm dia.heavy grade having embossed as ISI Mark galvanised iron pipes weight of 10.15 Kg/meter with necessary fittings. and remaking good the demolished portion and applying primer of anticorrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. completeSecond Floor

Third Floor

Providing and fixing screw down for 20 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.

Third Floor

Providing and fixing screw down for 25 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.

Third Floor

Providing and fixing screw down for 32 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.Second Floor

Third Floor

Providing and fixing screw down for 40 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.Second Floor

Third Floor

Providing, laying and fixing P.V.C. pipe of 50mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed

First Floor

Second Floor

Third Floor

Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. Complete

First Floor

Second Floor

Third Floor

Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete.

First Floor

Second Floor

Third Floor

Providing and fixing in position UPVC ultra violet stabilized 110 mm outer diameter cowl dome confirming to I.S.-4985 including making joints with solvent cement etc. Complete Second Floor

Third Floor

Providing and fixing 15 cm rigid PVC Nahani trap including PVC grating ,bend,connectingpiece of UPVC pipe up to the outside face of wall ,making the good damaged surface and testing etc. complete ( Prior approval of sample and brand by Ex. Engr. is necessary before use)

First Floor

Second Floor

Third Floor

Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. completeThird Floor

Providing and fixing P.V.C. Rain water pipes of 160mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc.complete.

Third Floor

Providing and fixing 45 cm wide mild steel ladder of 40mm x 6 mm mild steel flat stringers and steps of 18 mm dia. mild steel bar for water tank including fixing it in (1:2:4) M-15 cement concrete block 60cm x 30cm x 30cm and painting the ladder complete. (Anti Corossive Paint)Second Floor second floor

Third Floor

Providing and fixing 40 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirements etc. complete.Third Floor

Library/Staff chair : Providing and arrangement of Library/Staff chair with Seat and back to be made in Injection molded polypropylene. Seat is attached to the frame by the back attachment and with two steel Pal-nuts. and Backrest attached to the frame with two metal clips, Contains a contoured handle opening at the top for easy lifting and stacking, Chair Frame Construction is of Welded construction made primarily of 7/16" diameter steel wire (solid) bent to shape on a CNC wire bender. A 7-gauge steel seat strap, ribbed for added strength, supports the front of the seat and a 7/16" contoured steel rod joins the front legs for strength including all material, labour, transportation upto work site etc. complete. On all Floors

THREE SEATER STEEL LOUNGE SOFA :: Providing & fixing three seater steel lounge sofa of perforated sheet, chrome finish with leatherite seating as per approved sample and design including all material, labour, transportation upto work site etc. complete. on all Floors

SIDE TABLES : Providing of Premium Quality Coffee Table made out Rubber Wood 600x600mm in size including all material, labour, transportation upto work site etc. complete. on all Floors

ONE SEATER SOFA : Providing and making one seater sofa as per image shown. Complete frame in Pinewood + Plywood combination 32 Density premium quality foam. Spring Box for ultimate comfort. Metal Legs. Premium H. Leather aterial available in Brown color as well including all material, labour, transportation upto work site etc. complete.on all Floors

TWO SEATER SOFA : Providing and making two seater sofa as per image shown. Complete frame in Pinewood + Plywood combination 32 Density premium quality foam. Spring Box for ultimate comfort. Metal Legs. Premium H. Leather Material available in Brown color as well including all material, labour, transportation upto work site etc. complete. on all Floors

Three Seater Sofa: Providing and Macking three seater sofa as per image shown. Complete frame in plywood + Plywood combinition 32 density premium quality foam. Spring Box for Ulitmate comfort. Metal Legs premium H. Leather Material available in brown colour as well including all materials, labour, transportation upto work site etc. complete. on all Floors

CENTER TABLE : Providing of Premium Quality Coffee Table made out mdf Base 1000x700x420mm with Glass Top including all material, labour, transportation upto work site etc. complete. on all Floors

Bed Mattress: Providing and making Single bed Mattress with attractive tapestry, Double side quilted, High density bonded foam, PUF for superior comfort, Special double layer of memory foam, visco elastic (memory foam) with 3 years of warranty including all materials, labour, transportation upto work site etc. complete.on all Floors

Providing and fixing Canvas painting including all labour, material etc. complete. on all Floors

Bed Sheet for Single Bed- Providing Bombay Dyeing Bed Sheet Single bed of approved colour and brand,as per design,specification and drawing etc complete. Size 62" x108" on all Floors

Pillows for Bed- Providing Down lite made Pillows of size (16 x24 inches) of approved colour and brand,as per design,specification and drawing etc complete. on all Floors

Pillow Covers forPillows- Providing Bombay Dyeing made Pillow Covers For Pillows of size (17 x25 inches) of approved colour and brand,as per design,specification and drawing etc complete.on all Floors

Blanket - 60" x 90" Providing Single -Bombay Dyeing Blanket( 60 Inch x 90 inches) of approved colour ,as per design,specification and drawing etc complete. on all Floors

Bath Towel - 30" x 60" Providing Single -Bombay Dyeing Bath Towel(30 Inch x 60 inches) of approved colour ,as per design,specification and drawing etc complete.

Hand Towel - 16" x 30" Providing Single -Bombay Dyeing Hand Towel(16 Inch x 30 inches) of approved colour ,as per design,specification and drawing etc complete.

Providing and fixing T.V. Unit/shelf of size 1.80 x 0.60 x 0.75 m with 12 mm thickmarine ply, 4 mm thick veeners including, polishing use of all materials and carpenter charges including all material, labour, transportation upto work site etc. complete.

Single Bed : Providing and fixing wrought iron single bed size 36" x 78'' in wrought iron using 75x 40 mm rectangular section with horizontal support at 60cm c/c and 18mm thick commercial plywood of approved make.( Sample should be got approved by the Engineer in Charge)

Bunk Bed : Providing and fixing wrought iron Bunk bed size 36" x 78''x84"Ht. in wrought iron using 75x 40 mm rectangular section with horizontal support at 60cm c/c and 18mm thick commercial plywood of approved make.( Sample should be got approved by the Engineer in Charge) on all Floors

Cushions for Sofa- Providing Down lite made Pillows of size (12 x12 inches) with cover of approved colour and brand,as per design,specification and drawing etc complete.on all Floors

Concierge Desk- Providing and fixing of L-Shaped Concierge Desk of size 7'6"x2'6"x3'6" in 18mm thk. Ply Framework finished in 18mm thk. Marble cladding on external surfaces and Laminate finish on all internal surfaces including storage shutter and shelves with provision of indirect light and cutout for cable manager. on all Floors

Wall Clock- Providing and fixing of Digital Wall mounted Clocks on all Floors

Luggage Rack- Providing and fixing of Luggage Rack of 7'0"x24"x24"ht. In Metal fabrication base structure with double thickness Granite top pasted on 18mm thk. Bison Sheet. on all Floors

Commercial Garbage Collector : Providing and fixing FRP Wheeled Plastic Body Eco Elegant approx 120 ltrs. Garbage Collection Large Binon all Floors

Common Washroom Mirror - Providing & fixing mirror of size 24"x24" ht. with 6mm thick mirror glass, 12mm green ply, 4.0 mm green Decowood Anigrey vineer, finishing with three coat of sealer and two coat of Mellamyne polish of approved make to give smooth finish upto satisfaction of Engineer Incharge including all accesories & fittings, all material, labour, transportation upto work site etc. complete. on all Floors

Heavy Duty Floor Matt : Providing & fixing of Heavy Duty PVC Rubber matting of approx. 12mm thk. With necessary taping and fixing methodology as per approved by Architect. on all Floors

Commercial Weighing Machine: Providing & fixing of Heavy duty metal weighing machine with 50kg/100kg approximately weighing capacity.on all Floors

Trap Doors - Providing & Fixing of 18mm thk. Trap door finished in laminate on all sides with 18mm thk. Ply framework from ceiling with the necessary hardware and size as per design and detail approved by Cleint/ Architetct.on all Floors

Steel bench - Providing & Fixing of SS bench, 450mm deep with necessary hardware along with the Railing with additional support legs in SS if required. Design and detail as per approved by Cleint/ Architect.on all Floors

Wall Panelling : Wall Panelling : Providing and fixing panelling to the wall behind the bed/office table. The panelling made from 12 mm MDF supported by frame rafters of size 50 mm x 50 mm x 60 mm all over the wall upto ceiling, including lamination to the panelling with PVC Foil Membrane, etc. complete as per the drawings including all material, labour, transportation upto work site etc. complete. on all Floors

Executive table. :: Providing and fixing Executive table 1.80 Mx1.50Mx0.75 M made of 12 mm, 18 mm thick, marine plywood & 4 mm thick veeners with courian top, including malenine polishing use of adhesive all labour, material and carpenter charges etc. Complete as per the sample available in circle office with Providing and fixing table base with 18 mm thick, marine plywood & 4 mm thick veeners including malenine polishing use of adhesive channels,all labour, material and carpenter charges etc. including all fixtures and fastenings with runner of 0.90x0.45x0.75 M on all Floors

Blinds : Providing and fixing doors and window Blinds of best quality as per approved sample and brand by the Engineer in charge including stiching charges including all material, labour, transportation upto work site etc. complete.on all Floors

Office table for staff (1.5 x 0.75 x 0.75 m) : Providing & fixing office table top to be made up of 25mm thick prelaminated partical board with PVC edge band on all sides gable end and modesty pannel to be made up of 25mm thick prelaminated partical board with PVC edge band. front screen of table should be fully covered with 18 mm prelaminated partical board. 1 drawer and 1 shutter top supported pedestal to be made up of 18mm prelaminated board. Keyboard tray (without mouse tray) prelaminated board.to be made up of 18mm prelaminated partical board. etc. completed with runner of size 0.90x0.45x0.75M with same material as specified for tabl,including all fixtures and fastenings.on all Floors

Wardrobe - Providing & Fixing Almirah with 18 mm thick plywood of approved quality & ISI mark in single or double shutter including providing & fixing 1 mm thick formica of approved quality & ISI mark for all sides,width will be 450mm & ht 1800 mm including brass hinges of 100 mm,125 mm size brass handles, morties lock,shutter magnate,use of adhesive ,screwes ,nails,teak wood beeding of 25x6mm & 40x10 mm,abrow tape including frainch polishing etc.complete..on all Floors

Providing and fixing Acrylic name plates with acrylic letters in Golden colour or as directed by Engineer in charge including all material, labour, graphics, artist etc. completeon all Floors

Supplying wet waste dust bin having 6 litre capacity of any shape and colour as directed by Engineer in charge. The dust bins are made up from recycled plastic including all material, labour, transportation upto work site etc. complete.on all Floors

Supplying dry waste dust bin having 6 litre capacity of any shape and colour as directed by Engineer in charge. The dust bins are made up from recycled plastic including all material, labour, transportation upto work site etc. complete.on all Floors

Supplying recycled plastic buckets of 5 Litre capacity of approved make etc. complete as directed by Engineer Incharge. on all Floors

Supplying recycled plastic Mugs of 1 Lit capacity of approved make etc. complete As directed by Engineer in Charge on all Floors

News Paper & Magazine Stand- Providing and Placing in position Nwes paper stand SF L -10 Creative Make . All complete as per detail drawing, as specified and as directed by Architect / Consultant / Project - In - Charge.on all Floors

Openable Storage @ 900LX450Dx750HT: Providing and fixing of Openable storage at 900LX450Dx750HT to be made out of 25 mm thick top & 18 mm prelaminated partical board with openable laminate shutter & have a adjustable shelf as per design and drawing and instructions of engineer in charge including all material, labour, transportation upto work site etc. complete.on all Floors

CONSOLE (DINING AREA) : Providing and making of console, made out of Prelaminated Particle board 18 mm thickness with 2 shutter and 3 drawer as shown in picture. Matt Finish shutter & drawer facia, including all labour, installation charges, fixtures, fastening, accessories and transportation up to work site without damage etc. complete. All spacewood products are termite free & 3 years of manufacturing warranty. on all Floors

Curtain: Providing and Fixing door and windows curtain of best quality fabric as per approved sample and brand by the Engineer in charge including stiching charges including all material, labour, transportation upto work site etc. completeon all Floors.

Inaugration board made with glass (Sandwitch Type)with laminated digital painting including all material, labour, transportation upto work site etc. complete. on all Floors

Supplying and installing of Gautam buddha statue of life size in clay model, including plaster of paris dia, plaster of paris finish as directed by Engineer in charge with covering of 3mm thick reinforced fiber plastic (FRP), including primer coat, finishing and p.u. mat coat (Polyurethane coating) including all material, labour, transportation upto work site etc. complete. on all Floors

Supplying and installing of out door dust bins having 10 litre capacity of any shape and colour as directed by Engineer in charge. The dust bins are made up from reinforced fiber plastic (FRP) with 3mm thick with standard size, including primer coat and p.u. mat coat (Polyurethane coating) including all material, labour, transportation upto work site etc. complete. on all Floors

Supplying recycled plastic buckets of 15 Litre capacity of approved make etc. complete as directed by Engineer Incharge. on all Floors

Face Towel - 12" x 12" Providing Single -Bombay Dyeing Face Towel(12 Inch x 12 inches) of approved colour ,as per design,specification and drawing etc complete. on all Floors

Bath Mat- Providing and Laying door mat . All complete as per detail drawing, as specified and as directed by Architect / Consultant / Project - In - Charge. on all Floors

Door Mat- Providing and Laying KOUNCEPT Makedoor mat of size 61.2x39.2 cm. All complete as per detail drawing, as specified and as directed by Architect / Consultant / Project - In - Charge. on all Floors

Wooden Hanger Providing and Fixing in position solid wood wooden cloths hanger Non sleep design with Stell hooks Anshuman Make . All complete as per detail drawing, as specified and as directed by Architect / Consultant / Project - In - Charge. on all Floors

Providing & fixing mirror of size 1.20m x0.75m with 6mm thick mirror glass, 12mm green ply, 4.0 mm green Decowood Anigrey vineer, finishing with three coat of sealer and two coat of Mellamyne polish of approved make to give smooth finish upto satisfaction of Engineer Incharge including all accesories & fittings, all material, labour, transportation upto work site etc. complete. on all Floors

Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete.

First Floor

Second Floor

Third Floor

Providing and casting M30 garde self compacting concrete for fixing M.S. / FRP centering formwork at top and bottom for Arches etc. as per detailed designs and drawing or as directed including installing,removing with all necessary supportings, nail, binding wire, skilled and unskilled labour etc. including all lifts complete. Arch Type-6 (1.86 x 0.91 m) on all Floors

Providing and fixing in position after hoisting, precast 1:2 cement mortar reinforced jali 50 mm thick with 3 mm diameter mild steel bar reinforcement, of approved design on both side, fixing in cement mortar 1:3 and curing etc. Complete Ground floor

Providing and applying water proofing treatment using acrylic polymer modified cement based water proofing coating with fibre glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 sqm /kg with two coat using approved chemicals for masonry and concrete surface by brush covering 7 years guarantee on Stamp Papers etc. complete.

First Floor

Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9 mm with lock plate of 3.15 mm thickness reinforced with 35 x 35 x 5 mm angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65 mm and 3.15 mm respectively with hold fast arrangements, M.S. Bracket plate 300 x 300 x 3.15 mm minimum size and shape with square bar, suspension shaft of minimum 32 mm diameter, hood cover of M.S. sheet not less than 0.9 mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. (I.S. 62481979) (Without mechanical gear) Arch Type-6 (1.86 x 0.91 m) on all Floors

Providing and fixing in position at all heights GRC Grills as per detailed design and drawings with all finishing treatment required as per specification of Engineer in charge etc. complete Including all transportation charges. on all Floors

Providing and applying 2 Coats of 100% Pure acrylic water based paint with special heat reflectance property to withstand the harsh climate for period of atleast 10 years of approved make. Paint system should provide durable and long lasting finish with DFT of min 90 microns and should protect against concrete carbonation with R value of minimum 600 and equivalent concrete layer thickness value of min 150 cm. Paint should have breathability property and should be able to cover hairline cracks in the surface upto 0.5mm The paint has to be applied on a coat of high quality acrylic copolymer based alkali resistant primer with excellent penetrating properties including cleaning, with all leads and lifts at all levels etc complete, as directed by Engineer in charge on all Floors

Storage below counter :: Providing & fixing of undercounter storage of 36"x18"x30"ht. in 18mm thk. Ply finished in laminate on all sides with all the necessary hardware with drawers and shutters with shelf, all finished in laminate. on all Floors

Tall Storage: Providing & fixing ofTall Storage Unit of 48"x18"x84"ht. in 18mm thk. Ply finished in laminate on all sides with all the necessary hardware with drawers and shutters with shelf, all finished in laminate. on all Floors

Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top,40mm diameter and 1.5mm thick vertical supports spaced at 1.5m center to center and 8mm thick toughened glass including fabricating ,fixtures, errecting , necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete on all Floors

Providing and fixing in poistion at all heights Flag above dome of approved make, colour , size of flag in required positions (above Dome) with all necessary fittings along with length, dia. and finish to the pipe as per specification of Engineer in charge etc. complete Including all transportation charges. on all Floors

Providing and fixing in position at all heights Local Stone Cladding 150 mm wide as per detailed design and drawings from approved source with all finishing treatment required as per specification of Engineer in charge etc. complete Including all transportation charges. Arch Type-6 (1.86 x 0.91 m) on all Floors

Providing and fixing in position at all heights GRC Ceiling as per detailed design and drawings with all finishing treatment required as per specification of Engineer in charge etc. complete Including all transportation charges.

Providing and fixing in position at all heights Kalash Metal Tpye-1 of pure brass as per detailed design and drawings with all finishing treatment required as per specification of Engineer in charge etc. complete Including all transportation charges.Arch Type-6 (1.86 x 0.91 m) on all Floors

Providing and fixing in position at all heights Kalash Metal Tpye-2 of pure brass as per detailed design and drawings with all finishing treatment required as per specification of Engineer in charge etc. complete Including all transportation charges.Arch Type-6 (1.86 x 0.91 m) on all Floors

Providing and fixing in position Main Gate as per approved design and detailing in Cast Iron with all finishing treatment required as per specification of Engineer in charge etc. complete Including all transportation charges.

Providing and fixing in position at all heights Flag Pole with Fabric Flag of 50' high as per detailed design and drawings with all finishing treatment required as per specification of Engineer in charge etc. complete Including all transportation charges. on all Floors

Providing and fixing 20 to 25 mm thick rough shahabad box type waterproofing treatment to vertical outside faces of Reinforced Cement concrete walls of basement or underground floor including filling the gap of 25 mm between rough shahabad and R.C.C. walls with cement grout mixed with water proofing liquid Algae proof or other alike with one tile lift method, brushing the joints horizontally with cement slurry mixed with water proofing liquid for width 30 to 35 mm and sloping coping over topmost tile with cement mortar 1:3, butting the bottom most with Cement concrete 1:2:4 mixed with water proofing liquid, curing, with 7 years guarantee on court fee stamp of Rs.100/- with ponding test etc complete. (excluding Cement concrete 1:3:6 base concrete) on all Floors

Providing and fixing in position RCC FRP Grating of 450 mm wide of standard make as per specification of Engineer in charge etc. complete Including all transportation charges. Arch Type-6 (1.86 x 0.91 m) on all Floors

Providing and fixing heavy duty inter locking concrete Rubber mould glossy paving blocks of 80 mm thickness of having a strength of 400 kg/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc. complete. (using 100% crushed sand) on all Floors

Providing and casting in situ or precast tapering R.C.C. M-20 Mountable type Kerb without gutter ( as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant on all Floors

Providing and laying chequered tiles of approved quality of size 30 cm x 30 cm, confirming to corresponding I.S. for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.

Providing and laying in situ cement concrete M30 with tremix treatment for 200 mm thickness for flooring with groove cutting of 4mm wide and 20mm deep with necessary refilling with bitumen etc. complete.

Providing and fixing 80mm diameter water meter with non-return valve including strainer, sockets/ union nut and including water meter box making locking arrangement and lock. [Without chamber].

Providing and laying concrete pipes of I.S.NP. class of 150mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing and laying concrete pipes of I.S.NP. class of 225mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing and laying cement concrete pipe of IS 458:2003 NP-2 class of 450mm diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete.

Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry,plastering from inside and airtight C. I. cover of 75 kg with lid and frame fixed in cement concrete.

Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and C.I. lid cover of 75 kg with lid and frame fixed in cement concrete

Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with R.C.C. Cover medium duty 140 kg with frame etc complete.

Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry,plastering from inside and with frame fixed in cement concrete with R.C.C. Cover medium duty 140 kg with frame etc complete.

Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap

RWH - Shallow Percolation Pit providing, constructing 2.0m deep shallow depth percolation pit comprising of 1.0m dia pre-cast RCC rings, 300mm thick side filling around outside of RCC rings (annular space) with 40mm size boulders including filling of percolation pit up to 0.5m depth (from bottom up) with 25-75mm clean washed gravels followed by 0.5m depth of 10-25mm of clean washed stones followed by 0.5m of washed river fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) including netlon mesh between each gravel/fine aggregate (natural sand/crushed sand VSI grade finelywashed etc.) media layer including covering with RCC slab, manhole frame & cover, PVC rungs etc. including arrangement for inlet & outlet pipe, excavation & backfilling as shown in the drawing. The rate shallbe inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge

Providing and fixing in position Lamp on Compound Wall as per approved design and detailing in Cast Iron with all finishing treatment including flooring comprising of heat resistant colouring of approved make required as per specification of Engineer in charge etc. complete Including all transportation charges. on all Floors

Providing and fixing Indian teak wood plank ceiling 20 mm thick plain underside tongued and grooved including iron screws, scaffolding, if necessary, including one primer coat on under side and one coat of coal tar on upper side etc. complete on all Floors

Providing and fixing decorative teak plywood veneer lining 4 mm thick with backing of teak wood frame work of battens 12 mm X 25 mm at 30 cm center to center fixed to walls and pillars with 12 mm thik phywood building without skirting and cornice as per drawings including necessary iron work and finishing the exposed wood work with french polish etc. complete. on all Floors

Providing and fixing in position Sculpture of Elephant made of Sand Stone of 3.50 m x 2.55 m size as per approved design and detailing by applying lacker coat of Asian Ultima or equivalent brand with all finishing treatment required as per specification of Engineer in charge etc. complete Including all transportation charges. on all Floors

Providing and fixing in position Sculpture of Mahakali made of Sand Stone of 10' high size as per approved design and detailing by applying lacker coat of Asian Ultima or equivalent brand with all finishing treatment required including fixing it by approved make grouting material as per specification of Engineer in charge etc. complete Including all transportation charges at all height

Providing and fixing in position Statue made of Sand Stone of 2' high size as per approved design and detailing by applying lacker coat of Asian Ultima or equivalent brand with all finishing treatment required including fixing it by approved make grouting material as per specification of Engineer in charge etc. complete Including all transportation charges at all height Column Type-01 (24 No) Column Type-02 (53 No) Column Type-03 (26 no)

Providing and applying plastic emulsion paint of approved quality, colour and shade to old surface in three coats including scaffolding, preparing the surface. (excluding primer coat) etc. complete.

First Floor

Providing and applying external raincoat painting with crack filling acrylic polymer based chemical compound coating to the external surface of walls to prevent water seepage in the masonry walls during monsoon added with required shade Steiner to give required shade to the surface in two coats. Including providing three coat of priming of polymer base primer including preparing surface scrapping the existing loose old paint, removing loose particles of sand on the surface opening and cleaning the cracks developed in the external plaster, removing loose particles by chiseling, filling cracks by chemicals compound of approved make with proper penetration etc. Coating of Raincoat with the help of brush and as per instructions and specification given by manufacturer and with instruction from Engineer in-charge. Work shall be executed by certified applicator only and covering gurantee of 3 years on court stamp paper of Rs. 500/- and necessary testing etc. complete. on all Floors

Providing and fixing mild steel grill work for windows, ventilators etc. 20 kg/sqm as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. on all Floors

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C.coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) on all Floors

Providing and laying in trenches 80 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 10.15 kg/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing in position at all heights Shops Backlit Signes of 1.65 x 0.45 m as per detailed design and drawings with all finishing treatment required as per specification of Engineer in charge etc. complete Including all transportation charges. on all Floors

Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc. on all Floors

Dismantling the R.C.C. Work 1:2:4 and sorting out the materials such as steel etc. as directed and stacking them within the specified lead as directed etc. complete. on all Floors

Providing and applying pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete.

First Floor

Second Floor

Third Floor

Transporting excess stuff available from cutting, dismentalling including convaying and disposing suaitabaly with 5.0 km avg lead

Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading for embankment or stacking as directed.

Watering and compacting of embankment formed of materials obtained from the road cutting within a lead of 50 m, not less than 97% of standard Proctor density after laying them in layers of 20 cm. to 30 cm. with Power roller.

Providing earth work in embankment with approved materials obtained from other sources upto lead of 50m. including all lifts, laying in layers of 20cm. to 30cm. thickness breaking clods, dressing to the required lines, curves, grades & section, watering and compaction with vibratory roller with V-Sat attachment to achieve not less than 97 % of standard proctor density etc. complete ( Material obtained from Other sources)

Supplying & erecting H.M.S. P.V.C. conduit 20 mm. dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying & laying HMS PVC conduit 20 mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying & erecting HMS P.V.C. conduit 25 mm. dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying & laying HMS PVC conduit 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying & erecting HMS P.V.C. conduit 32 mm. dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying & laying HMS PVC conduit 32mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying & erecting mains with 2x1.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying & erecting mains with 1x1.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying & erecting mains with 2x2.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying & erecting mains with 1x2.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying & erecting mains with 2x4 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying & erecting mains with 4x4 sq.mm F.R copper PVC insulated wire laid in provided conduit/ trunking /inside pole/ Bus bars or any other places. as per specification No: WG-MA/BW (LDB Circuit)

Supplying & erecting mains with 1x4 sq.mm F.R copper PVC insulated wire laid in provided conduit/ trunking/ inside pole/ Bus bars or any other places. as per specification No: WG-MA/BW (LDB Circuit earth)

Supplying & erecting mains with 2x6 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying & erecting mains with 4x6 sq.mm F.R copper PVC insulated wire laid in provided conduit/ trunking/ inside pole /Bus bars or any other places as per specification No: WG-MA/BW (PDB & Main LDB Circuit) (Rs 103 x 2 = 206)

Supplying & erecting mains with 1x6 sq.mm F.R copper PVC insulated wire laid in provided conduit/ trunking/ inside pole/ Bus bars or any other places as per specification No: WG-MA/BW (PDB Circuit earth) (Rs 103 /2 = 51.50)

Supplying & erecting mains with 4x10 sq.mm F.R copper PVC insulated wire laid in provided conduit/ trunking/ inside pole/ Bus bars or any other places as per specification No: WG-MA/BW (Main PDB Circuit)

Supplying & erecting mains with 1x10 sq.mm F.R copper PVC insulated wire laid in provided conduit/ trunking/ inside pole/ Bus bars or any other places as per specification No: WG-MA/BW (PDB Circuit earth)

Supplying & erecting mains with 4x25 sq.mm F.R copper PVC insulated wire laid in provided conduit/ trunking/ inside pole/ Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type switch 16 / 20 A with indicator, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type D.P. switch 32A with indicator, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type 3 pin 6A multi sockets with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI marked modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type computer jack RJ 45 with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 1 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the bacOne Kilo Gramround.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the bacOne Kilo Gramround.

upplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the bacOne Kilo Gramround.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the bacOne Kilo Gramround.

1-w Point wiring for light/fan/bell concealed type in min 20 mm ISI marked HMS PVC conduit with 1.5 sq.mm. (2+1E) FR grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/CW

2-w Point wiring for light/fan/bell concealed type in min 20 mm ISI marked HMS PVC conduit with 1.5 sq.mm. (2+1E) FR grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/CW (Dormitory Staire)

Wiring for plug on board with modular Switch socket, copper wiring and earthing as per specification No: WG-PW/SW

Wiring for plug on board with Switch socket concealed type, copper wiring and earthing and with modular accessories as per specification No: WG-PW/CW

Point wiring for light/fan/bell hybrid type (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FR grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/HW

Secondary point wiring for additional light/ bell point, concealed type in min 20 mm PVC conduit with 1.5 sq.mm. (2+1E) FR/FRLSH grade copper wires with required accessories as per specification No: WG-PW/CW

Point wiring in ISI mark HMS PVC conduit with 1.5 sq.mm (2+1E) FR grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Supplying & erecting telephone copper cable 2 pair with 0.5 mm dia. laid in provided PVC casing capping/ conduit as per specification No. WG-TW

Supplying, erecting & commissioning junction box suitable for 10 pairs as per specification No. WG-TW

Supplying & installing UTP networking cat-6 cable suitable for LAN / WAN Computer net-working as per specification No. WG-COC/NC

Supplying LED concealed type foot / step light with aluminium body for indoor/outdoor application suitable for upto 4W-6W LED including driver and erecting by making necessary arrangement/recess in wall to make it flush with surface.

Supplying &erecting ready to use Retrofit T8 LED 18 / 20 tube light with polycarbonate body, heat sink, integrated HF electronic driver complete & compatible to T8 / T12 LED luminaire by disconnecting starter & ballast if necessary.

Supplying & erecting decorative pre-wired box type fitting/batten suitable for 4 feet, T8 LED tube light (excluding tube light).

Supplying and erecting ding dong / electronic musical type call bell with heavy duty coil suitable to operate on 230V A.C. supply erected on polished double wooden block/sunmica block of suitable size

Supplying and erecting LED street light fitting suitable for 24W, with PF > 0.95 class IP 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete as per specification No FG-ODF/FLS-2.

Supplying and erecting street light Wall bracket made from 25 mm. dia ‘B’ class G.I. pipe 1.2 m in total length complete as per specification no. FG-BKT/WB

Supplying & erecting 10-12W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Supplying and erecting fresh air cum exhaust fan of light duty 250 V A.C. 50 cycles 300mm. 1400 RPM rust proof body & blades, wire mesh, duly erected in an approved manner.

Supplying and erecting five star rated energy saving Ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Supplying and erecting square shaped CRCA /die-cast aluminium powder coated housing LED panel light (slim edge-lit) suitable for upto 8 W with provision for plane front frame with translucent cover fixed to the housing complete.

Supplying and erecting square / round shaped CRCA /die-cast aluminium powder coated housing LED panel ( slim edge-lit) light suitable for 18W with provision for plane front frame with translucent cover fixed to the housing complete.

Supplying and erecting CRCA /die-cast aluminium powder coated housing LED panel light (slim edge-lit) square / round shape suitable for 24 W with provision for plane front frame with translucent cover fixed to the housing complete.

Supplying and erecting square shaped CRCA /die-cast aluminium powder coated housing LED panel light (slim edge-lit) 600x600mm suitable for 36W-40W with provision for plane front frame with translucent cover fixed to the housing complete.

Supplying and erecting LED flexible strip light 5m length upto 25W conforming IP 65 of any colour with driver complete.

Supplying and erecting moon type decorative wall/ceiling mounted fixture including LED upto 12W circular/square type with opaque diffuser and electronic driver including bracket complete. (for Track Light)

Supplying and erecting LED Flood light fitting of 80W, including lamp, with PF > 0.95,class IP 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete per specification No FG-ODF/FLS-2 (Toilet Block)

Supplying and erecting Recess mounted 30W LED wall washers, tilted 70° outwards and swivels 360° to offer best illumination on the wall with any colour with driver complete. ( Including Compatible Driver)

Supplying & erecting 20W LED PAR (30 Lamp E-27 Base, SPOTO series) lights by making necessary arrangement/recess in wall to make it flush with surface.

Supplying and erecting fan hook box of 10 mm M.S. round bar bounded to the R.C.C. bars upto 50 mm length each side and pierced through a 16 S.W.G. thick aluminium/M.S. Bowl 100 mm dia.or equivalent square size and having depth upto 75 mm complete erected with duly painted by one coat of red oxide paint and two coats of paint erected in position and without any leakage of slurry of cement concrete on either side of the box and positioned to the bottom level of the slab.

Supplying, installing, testing and commissioning split type variable speed inverter technology room Air conditioning unit 2 TR capacity having ISEER minimum 4.50 suitable to operate on 250V, 50 cycles, A.C. supply having 1 no. of air handling unit hi-wall/ floor mounting type complete with Refrigerants R410 A /R32 and copper condenser at position. specification no. APAC/ SAC

Supplying, installing, testing and commissioning cassette type variable speed inverter technology split room airconditioning unit 2 TR capacity having ISEER minimum 3.50 to maximum 3.99 suitable to operate on 230/250 V, 50 cycles, AC supply having 1 no. air handling unit false ceiling mounting type complete with refrigerant R32/R410A and copper condenser coil at position as per specification with provided copper piping and drainage pipe.

Supplying & erecting soft drawn copper pipe suitable for refrigeration system having 22 SWG thickness and inner dia / size 16 mm complete.

Supplying & erecting on line UPS pure sine wave of 5 kVA capacity complete with standard features, along with necessary SMF batteries for 30 mins battery backup, as per specification no. AP-UPS

Supplying, erecting & terminating XLPE armoured cable 2 core 4 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (Deep Stambha-345 mtr)

Supplying, erecting & terminating XLPE armoured cable 2 core 6 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting &terminating XLPEarmoured cable 4 core 6 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting &terminating XLPEarmoured cable 4 core 10 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting &terminating XLPEarmoured cable 4 core 16 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting &terminating XLPEarmoured cable 3½ core 25 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (Existing Samadh-40, BB9-51, BB10-56, BB7-56, BB6-64, BB4-84, BB5-72)

Supply, Installation, Testing and commissioning of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 One Kilo Gram Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete. Specification no. EA-MOBI

Supplying and erecting aluminium strip of required sizes used for earthing on wall and/or any other purpose with necessary aluminium clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no EA-EP.

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.. (MCCB Panel Cable)

Supplying & installing co-axial copper cable low voltage grade RG-6 as per specification No. WG-TW (3rd Floor Suit- 14 No and Bhakta Rang-1)

Supplying, installing, testing and commissioning split type variable speed Inverter technology room Air conditioning unit 1.5 TR capacity having ISEER minimum 4.50 suitable to operate on250V, 50 cycles, A.C. supply having 1 no of air handling unit hiwall / floor mounting type complete with refrigerant R410 A/R32 and copper condensor at position. specification no.APAC/ SAC (Suit-7 No)

Supplying & erecting soft drawn copper pipe suitable for refrigeration system having 22 SWG thickness and inner dia / size 32 mm complete. (2nd floor Suit-15x7 = 105)

Supplying and erecting luminous / modular type call bell indicator with plastic body, heavy duty coil and indicator lamp working on 230V A.C. supply with resetting arrangement complete erected on double wooden/ sunmica board (Suit-7 No)

Supplying and erecting ‘B’ grade G.I. pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire. (for ceiling Fn)

Supplying, erecting & marking SPMCB 6A to 32A, C-series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking DPMCB 6A to 32A, C- series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking TPMCB 6 A to 32A in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking TPMCB 40A to 63A in provided distribution board as per specification no. SW-SWR/MCB

Supplying erecting and marking four pole isolators only switch version of miniature circuit breakers of 63A in provided distribution board complete.

Supplying erecting and marking four pole isolators only switch version of miniature circuit breakers of 80/100A in provided distribution board complete.

Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SPMCB of 12 ways, on iron /GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SPMCB of 24 ways, on iron/ GI frame/wooden board.(horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SP / TP MCBs of 12 ways, on iron/ GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SP / TP MCBs of 24 ways on iron/ GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/flush mounted with 2 ways for incoming and 6 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB

Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/flush mounted with 2 ways for incoming and 10 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted suitable for 3 pole MCCB as incomer & outgoing SP MCB (12 poles) or TP MCB of 4 ways (12 poles) on iron/ GI frame. (vertical busbar type) as per specification no. SW-SWR/MCBDB1

Providing & erecting 3 Pole MCCB upto 100A, 415V, with short circuit rating 25 kA (Ics=100% of Icu ),adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Providing & erecting 4 Pole MCCB upto 100A, 415V, with short circuit rating 25 kA (Ics=100% of Icu ),adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Providing & erecting 3 Pole MCCB of 200A,415V capacity with short circuit rating 25 kA (Ics=100% of Icu) adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Providing & erecting 4 Pole MCCB of 200A,415V capacity with short circuit rating 25 kA (Ics=100% of Icu) adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Providing & erecting 4 Pole MCCB of 250A,415V capacity with short circuit rating 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Supplying, fixing and commissioning 2 pole RCBO (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 32A/40A as per specification no SW-RCCB/RCBO

upplying, fixing and commissioning 2 pole RCBO (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 63A, as per specification no SW-RCCB/RCBO

Supplying, fixing and commissioning 4 pole RCBO ( (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 32A/40A as per specification no SW-RCCB/RCBO

Providing & erecting floor / wall mounting, MCCB panel board with door suitable for four pole incoming 250A, 4 ways four pole outgoing upto 100 A MCCB's on iron frame, as per specification no SW-SWR/MCCBPB. (Excluding MCCB'S)

Providing & erecting floor / wall mounting, MCCB panel board with door suitable for four pole incoming 250A, 6 ways four pole outgoing upto 100 A MCCB's on iron frame, as per specification no SW-SWR/MCCBPB. (Excluding MCCB'S)

Providing & erecting incoming and outgoing cable alleys suitable for MCCB panel board with door of 250A incoming and 4 way outgoing or 400A incoming and 2 way outgoing made from CRCA sheet 1.6 mm thick duly powder coated and having vertical insulated partition for shielding between the shared face of cableway and DB complete.

Providing & erecting incoming and outgoing cable alleys suitable for MCCB panel board with door of 250A incoming and 6 way outgoing or 400A incoming and 4 way outgoing made from CRCA sheet 1.6 mm thick duly powder coated and having vertical insulated partition for shielding between the shared face of cableway and DB complete.

Supplying and erecting four pole metal clad ON LOAD change over switch 415V,100A erected on angle iron /GI frame complete.

Supplying and erecting four pole metal clad ON LOAD change over switch 415V, 200A erected on angle iron /GI frame approved make complete.

Supplying and erecting four pole metal clad ON LOAD change over switch 415V,320A erected on angle iron /GI frame complete.

Supplying and erecting PVC insulated PVC round sheathed 1.5 sq.mm (30 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 Kv

Supplying and erecting LED Street light fitting suitable for above 48W lamp, including lamp, with PF > 0.95 class IP 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete per specification No . FG-ODF/FLS2. (Single arm- 70+29= 99 AND Double arm 15+13= 28)

Supplying, erecting & marking SPMCB 6A to 32A (B-series) in provided distribution board as per specification no. SW-SWR/MCB (Street Light Pole)

Supplying & erecting 415V 16A porcelain base neutral link complete erected in provided MS box complete.

Supplying, erecting &terminating XLPEarmoured cable 4 core 6 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (Street light pole- 2742 and Dwarka Light-3120).

Supplying, erecting & terminating XPLE armoured cable 4 core 10 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (Street light panel & DB)

Supplying, erecting & terminating XPLE armoured cable 4 core 16 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (For High-Mast)

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete (for street light cable, High-Mast cable)

Providing & erecting 5 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL.

Providing and erecting galvanised 1000mm single arm sword type bracket with FRP dome and ball as per specification no. OH-PL/PBKT

Providing and erecting galvanised 1000mm double arm sword type bracket with FRP dome and ball as per specification no. OH-PL/PBKT

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Providing pipe type earthing with 20mm Dia GI Pipe rod complete with all material as per specification no. EA-EP.

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation, fixing provided nut bolts with the help of template, duly plastered as per design complete (for 5m octagonal-127 AND Dwarka Pole-158).

Supplying and erecting triple pole and neutral distribution board (TPNDB) surface/ flush mounted suitable for SPMCB of 24 ways on iron / GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

SProviding, erecting and commissioning 4 pole RCCB only of electromagnetic type with 30/100/300 mA sensitivity and having capacity of 40A complete as per specification no. SW-RCCB/RCCB

Supplying and erecting 16 m (clear height) High Mast (Top-150mm, Bottom- 360mm) with lowering and raising motorized unit, lantern carriage assembly suitable for max. 8 nos. luminaries and its control gear box, lightning finial arrangement for fixing aviation light and foundation bolts on provided foundation as per specification no. OH-PL/HM (excluding luminaries).

Supplying and erecting Outdoor Stand Mounted Feeder Pillar for highmast of the same manufacturer with 63A TPN MCB incomer, single dial timer switch, 45A TP contactor for automatic switching of luminaries, 2 nos 9A contactors and raise/lower push button, and provision for termination of adequate size of incoming and outgoing cables erected in min. 14 SWG CRCA sheet box powder coated with supporting angles, self-lock, gasket and slanting top erected with CC foundation complete .

Making M- 20 cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq. m at 2 m depth including excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 16 m raising lowering high mast).

Supplying and erecting LED Flood light fitting of 150W, including lamp, with PF > 0.95,class IP 65 and above Housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete per specification No FG-ODF/FLS-2 (8 No on each High mast)

Cast Article (DLP-2-35-401)Of 3.5 Mtr. Iron Decorative Lamp Post, Cast Article (DBR-019-D) Iron Decorative Double Arm Bracket, Cast Article (DGL-048-S) Of Aluminium 2 Nos. Decorative Light Fixture With 50 Watt LED Light. Make : DWARKA LIGHTS.

ast Article (DLP-2-35-401)Of 3.5 Mtr. Iron Decorative Lamp Post, Cast Article (DBR-019-D) Iron Decorative Single Arm Bracket, Cast Article (DGL-048-S) Of Aluminium 1 Nos. Decorative Light Fixture With 50 Watt LED Light. Make : DWARKA LIGHTS. (Near Mandir Area, Samai).

Cast Article (DBR-019-S-C (U)) Of Iron Decorative Wall Bracket. Cast Article (DGL-048-S) Of Aluminium Decorative Light Fixture With 50 Watt LED Light. Make : DWARKA LIGHTS (Compound Wall).

Supplying & erecting mains with 2x1.5 sq.mm. F.R. copper wire, in 16 gauge 20 mm dia. Rigid Steel conduit with continuous GI earth wire of 2.5 sq.mm. as per specification No: WG-MA/MC. (5 mtr for 1 Lift)

Supplying & erecting mains with 2x2.5 sq.mm. F.R. copper wire, in 16gauge 20 mm dia. rigid steel conduit, with continuous GI earth wire of 2.5sq.mm. as per specification No: WG-MA/MC (28 mtr for 1 Lift)

Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete

Supplying and erecting ISI mark modular type switch 16A duly erected on provided plate and box with wiring connections complete

Supplying and erecting ISI mark modular type 3 pin 6A multi sockets with safety shutter, duly erected on provided plate and box with wiring connections complete

Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 modules duly erected.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 modules duly erected.

Point wiring for light/fan/bell in 20 mm metal conduit with 1.5 sq.mm (2+1E) FR grade copper wire, Modular type switch, earthing and required accessories as per specification No: WGPW/ SW (Rs 691.00 + add Rs. 193 for moduler switches)

Wiring for plug on board with Modular Switch socket, copper wiring and earthing as per specification No: WG-PW/SW

Supplying & erecting LED 20W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete.

Supplying and erecting bulkhead fitting suitable for upto LED upto 12W fixed on wall. As per specification no. FG-IDF/BHF

Supplying & erecting 10-12W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Supplying, erecting & marking SPMCB 6A to 32A, C-series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SWSWR/ MCB

Supplying, erecting & marking DPMCB 6A to 32A, C- series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting single pole and neutral distribution board (SPNDB) surface/flush mounted with 2 ways for incoming and 2 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB (LIFT ROOM)

Supplying and erecting single pole and neutral distribution board (SPNDB) surface/flush mounted with 2 ways for incoming and 6 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB (LIFT ROOM)

Providing, erecting and commissioning 4 pole RCCB of electromagnetic type with 30/100/300 mA sensitivity and having capacity of 63A complete as per specification no. SWRCCB / RCCB

Supplying, erecting & terminating XLPE armoured cable 2 core 4 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XPLE armoured cable 4 core 16 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (For High-Mast)

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results asper specification no. EA-EP

Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no EA-EP.25x3 GI Strip - 30 Mtr x 0.59 One Kilo Gram/Mtr = 17.7 One Kilo Gram x 1 Lifts = 17.7 One Kilo Gram.

SITC of Electric Traction Passenger Lift with · Rated capacity :- 8 Passenger/544One Kilo Gram Floors :- G+3 floor (4Stops/4 Landings) Travel :- 16 mtrs· Location of Lift Machine:- MR Rated speed :- 1.0mps VS · Doors type :- COPO/TOPO Doors with frame having clear opening of 800 mm wide x 2000 mm high made from SS 304 grade sheet of 1.5mm, thick in hairline finish for car and all landing doors with SS door architraves/frames · Lift car enclosure made from SS 304 grade sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. · COP with SS face plate having metallic push buttons with Braille Code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with/without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor Clear Car size of 1350mm wide x 1100mm deep x 2000mm high LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille Code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings · Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port, control panel duly wired with proper size & strength copper wire for power & control circuit, with provision for addition of floor/ control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class ARD complete with necessary SMF VRLA batteries .( For Detaie Wording of Item Refer tender Book let and Technical Speciifcation)

Supplying & erecting mains with 2x1.5 sq.mm. F.R. copper wire, in 16 gauge 20 mm dia. Rigid Steel conduit with continuous GI earth wire of 2.5 sq.mm. as per specification No: WG-MA/MC. (5 mtr for 1 Lift)

Supplying & erecting mains with 2x2.5 sq.mm. F.R. copper wire, in 16gauge 20 mm dia. rigid steel conduit, with continuous GI earth wire of 2.5sq.mm. as per specification No: WG-MA/MC (28 mtr for 1 Lift)

Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete

Supplying and erecting ISI mark modular type switch 16A duly erected on provided plate and box with wiring connections complete

Supplying and erecting ISI mark modular type 3 pin 6A multi sockets with safety shutter, duly erected on provided plate and box with wiring connections complete

Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 modules duly erected.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 modules duly erected.

Point wiring for light/fan/bell in 20 mm metal conduit with 1.5 sq.mm (2+1E) FR grade copper wire, Modular type switch, earthing and required accessories as per specification No: WGPW/ SW (Rs 691.00 + add Rs. 193 for moduler switches)

Wiring for plug on board with Modular Switch socket, copper wiring and earthing as per specification No: WG-PW/SW

Supplying & erecting LED 20W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete.

Supplying and erecting bulkhead fitting suitable for upto LED upto 12W fixed on wall. As per specification no. FG-IDF/BHF

Supplying & erecting 10-12W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Supplying, erecting & marking SPMCB 6A to 32A, C-series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SWSWR/ MCB

Supplying, erecting & marking DPMCB 6A to 32A, C- series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting single pole and neutral distribution board (SPNDB) surface/flush mounted with 2 ways for incoming and 2 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB (LIFT ROOM)

Supplying and erecting single pole and neutral distribution board (SPNDB) surface/flush mounted with 2 ways for incoming and 6 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB (LIFT ROOM)

Providing, erecting and commissioning 4 pole RCCB of electromagnetic type with 30/100/300 mA sensitivity and having capacity of 63A complete as per specification no. SWRCCB / RCCB

Supplying, erecting & terminating XLPE armoured cable 2 core 4 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XPLE armoured cable 4 core 16 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (For High-Mast)

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results asper specification no. EA-EP

Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no EA-EP.25x3 GI Strip - 30 Mtr x 0.59 One Kilo Gram/Mtr = 17.7 One Kilo Gram x 1 Lifts = 17.7 One Kilo Gram.

SITC of Electric Traction Passenger cum Stretcher/ Hospital Lift with Rated capacity :- 15 Passenger/1020One Kilo Gram · Floors :- G+1 floor (2Stops/2 Landings) · Travel :- 14 mtrs · Location of Lift Machine:- MR Rated speed :- 1.0mps VS Doors type :- COPO/TOPO Doors with frame having clear opening of 800/900/1000 mm wide x 2000mm high made from SS 304 grade sheet of 1.5mm, thick in hairline finish for car and all landing doors with SS door architraves /frames · Lift car enclosure made from SS 304 grade sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc.( For Detaie Wording of Item Refer tender Book let and Technical Speciification)

Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority. (For generator foundation- 4 No)

Excavating soft murum / soft soil road by chiselling for preparing pit for poles stay or earth plates or for laying cables, pipes & clearing the site by removing debris & making the site good complete. (For generator foundation- 4 No)

Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) mm. stone metal duly plastered with necessary curing for complete. (For generator foundation- 4 No)

Supplying, erecting and commissioning of diesel generating set with alternator of 62.5 kVA output continuous rating, 3 phase, 415 V, 50c/s 0.8 p. f. A.C a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet, sound absorbing material to restrict sound level upto 75 dB at 1.0 m, provided with first filling of oil, diesel etc. as per specification no. GEN-DG (Museum-1 & Toilet Block-1).

Supplying, erecting, testing and commissioning of Microprocessor based AMF panel suitable for diesel generating set of above 50 kVA upto 62.5 kVA capacity Single/Three phase, 230/415 Volts, 50Hz A.C. with all standard features, safeties etc as per specification no. GEN-AMF.

Supplying, erecting and commissioning of diesel generating set with alternator of 160 kVA output continuous rating, 3 Phase, 415 V, 50c/s 0.8 p. f. A.C a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite Acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet, sound absorbing material to restrict sound level upto 75 dB at 1.0 m, provided with first filling of oil, diesel etc. as per specification no. GEN-DG (Dormitory)

Supplying, erecting, testing and commissioning of Microprocessor based AMF panel suitable for diesel generating set of above 140 kVA upto 180 kVA capacity Single/Three phase, 230/415 Volts, 50Hz A.C. with all standard features, safeties etc as per specification no. GEN-AMF.

Supplying, erecting and commissioning of diesel generating set with alternator of 200 kVA output continuous rating, 3 Phase, 415 V, 50c/s 0.8 p. f. A.C a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet, sound absorbing material to restrict sound level upto 75 dB at 1.0 m, provided with first filling of oil, diesel etc. as per specification no. GEN-DG

Supplying, erecting, testing and commissioning of Microprocessor based AMF panel suitable for diesel generating set of above 180 kVA upto 200 kVA capacity Single/Three phase, 230/415 Volts, 50Hz A.C. with all standard features, safeties etc as per specification no. GEN-AMF.

Supplying, erecting &terminating XLPEarmoured cable 3½ core 300 sq. mm. aluminium conductor with continuous 12.97 sq. mm. (8 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 160 mm outsidedia, double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Supplying & erecting G.I. pipe ‘A’ class 75 mm dia. erected for enclosing XLPE armoured cable on wall/pole as per specification no. CB-CE (for road crossing)

Supplying and erecting bus bar chamber triple pole with neutral with four aluminium bars, 500V, 100A complete as per specification no. CP-BB (1 for 9 No shop at Position-9, 1 for 9 No shop at Position-11, 1 for 9 No shop at Position-14, 1 for 12 No shop at Position-21, 1 for 9 No shop at Position-33, 1 for 9 No shop at Position-34, 2 for18 No shop at Position- 19, 1 for 15 No shop at Position-46, 2 for 24 No shop at Position-47))

Supplying, erecting &terminating XLPEarmoured cable 3½ core 25 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting &terminating XLPEarmoured cable 3½ core 35 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting &terminating XLPEarmoured cable 3½ core 50 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 3½ core 70 sq. mm. aluminium conductor with continuous 8.35 sq. mm. (10 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 3½ core 95 sq. mm. aluminium conductor with continuous 8.35 sq. mm. (10 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL.

Supplying, erecting & terminating XLPE armoured cable 3½ core 120 sq. mm. aluminium conductor with continuous 8.35 sq. mm. (10 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL.

Supplying, erecting &terminating XLPEarmoured cable 1100 V. 3½ core 185 sq. mm. aluminium conductor with continuous 12.97 sq. mm. (8 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL.

Supplying, erecting &terminating XLPEarmoured cable 3½ core 300 sq. mm. aluminium conductor with continuous 12.97 sq. mm. (8 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL.

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete..

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 146 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete. (MCCB Panel Cable)

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 160 mm outsidedia, double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Providing & erecting floor / wall mounting, MCCB panel board with door suitable for four pole incoming 250A, 4 ways four pole outgoing upto 100 A MCCB's on iron frame, as per specification no SW-SWR/MCCBPB. (Excluding MCCB'S) (T3- A Panel)

Providing & erecting floor / wall mounting, MCCB panel board with door suitable for four pole incoming 250A, 6 ways four pole outgoing upto 100 A MCCB's on iron frame, as per specification no SW-SWR/MCCBPB. (Excluding MCCB'S) (T3- B Panel and T3- C Panel)

Providing & erecting 3 Pole MCCB upto 100A, 415V, with short circuit rating 25 kA (Ics=100% of Icu ),adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB (MCCB Panel outgoing- A-12, B-8, C-8, D-8, E-8)

Providing & erecting 4 Pole MCCB of 200A,415V capacity with short circuit rating 25 kA (Ics=100% of Icu) adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Providing & erecting incoming and outgoing cable alleys suitable for MCCB panel board with door of 250A incoming and 8 way outgoing or 400A incoming and 6 way outgoing made from CRCA sheet 1.6 mm thick duly powder coated and having vertical insulated partition for shielding between the shared face of cableway and DB complete.

Supplying & laying (including excavation) 25 cm dia RCC Hume pipe of standard thickness at required depth up to 90 cms. below road / ground surface, for covering provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet).

Supplying and erecting GI sheet 1.6 mm (16 SWG) to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint. (8 m2 for 1 No panel X 5 No panel= 40 m2)

Supplying and erecting Iron, sheet metal work consisting of CRCA Sheets, Various sections of iron, Plates, Chequered Plates, Rods, Bars, MS pipes, etc. for panel board or any other purposes complete with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority (22 One Kilo Gram for 1 No panel X 5 No panel= 110 One Kilo Gram)

Providing & erecting 4 Pole MCCB of 315/400A, 415V capacity with short circuit rating 36 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB (315A-1 No for each panel)

Supplying and erecting triple pole metal clad HRC fuse switch 415V, 300-320 A with neutral link with HRC fuses, on angle iron / GI frame as per specification no. SW-SWR/TPHRC. (2 No in each panel, toatl panel-4 x 2 = 8 No) (less 25%, will be installed in febricated panel Rs 9373 - 25% ))

Supplying and erecting self-locking arrangement with keys in duplicate, made of brass duly erected, flush with surface of panel / cupboard.

Supplying and erecting of any size electrolyte aluminiumpatti or bar in bus bar chamber / in panel or any other purpose, 500 V with require capacity with 99.9% aluminium purity with fixing arrangement (like lug or bottle type lug) to both the end with high grade polyolefin insulation sleeve complete as per specification no. BCP-BB

Supplying and erecting panel mounting type digital ammeter having three and half digit LED display, external CT operated, calibrated for suitable to operate on 500V, 0 to 1000A AC supply with necessary PVC wire leads and lugs and mounting hardware on provided panel complete with calibration certificate from manufacturer.

Supplying and erecting panel mounting type digital voltmeter having three and half digit LED display, calibrated for 0 to 750V AC suitable to operate on 500V AC supply with necessary PVC wire leads and lugs and mounting hardware on provided panel complete with calibration certificate from manufacturer.

Supplying and erecting LT current transformer with bar primary 50/5 to 1000/5 ratio with 15 VA burden erected in provided CRCA box duly secured with insulating materials connected to the meter with test certificates.

Supplying and erecting set of 3 pilot lamps all bakelite with colour glasses with miniature lamps 230 V/250V erected on provided CRCA box with panel type fuses and connected with PVC wires.

Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Excavating soft murum / soft soil road by chiselling for preparing pit for poles stay or earth plates or for laying cables, pipes & clearing the site by removing debris & making the site good complete.

Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) mm. stone metal duly plastered with necessary curing for complete. (pole muffing or any other purpose).

Supplying and erecting GI sheet 1.6mm (16 SWG) caution board of size 250 x 200 mm duly painted with red oxide and enamel paint in Marathi and Hindi erected at position for HV/EHV installation. (for 2 pole)

Supplying and erecting rolled steel joist (girder) pole 100 x 116 mm (23 One Kilo Gram/m) with provided base plate in provided foundation as per specification no. OH-PL/RSJ

Supplying and erecting bracket for guarding of HT OH Line, made from channel iron 1600 mm in length and 75x40x6 mm. erected on pole complete as per specification no. OH-PL/VCA

Supplying and erecting vee cross arm with ISM channel of 75x40x6mm, for 11kV HTOH line with arrangement to fix insulator at 45mm from the end & horizontal distance between insulators 1220 mm bent at angle of 60 degree keeping base 305 mm and the total vertical height of V cross arm as 460mm, and fixed on pole with MS clamp of 80x10 mm, nut bolts,washers complete as per specification no. OH-PL/VCA

Supplying and erecting 75x40x6 mm with 4.4 mm thick web and 7.3 mm thick flange channel (top pin) with clamp of suitable length so as to maintain vertical clearance of 1065 mm for 11 kV,1320 mm for 22 kV between insulators for erection of top pin insulators complete as per specification no. OH-PL/VCA

Supplying and erecting porcelain pin type insulator with G.I. pin suitable for 11kV line, complete as per specification no. OH-INS/PN

Supplying and erecting ACSR conductor of size - 6/1-2.59 mm complete. (Weasel) (127.7 One Kilo Gram/km) as per specification no. OH-CON/ACSR

Supplying and erecting G.I. stay set for poles, including loop insulators at inaccessible height complete with anchor plate 300 x 300 x 6 mm., straining screws, G.I. stay wire 7/8 SWG, G.l. stay rod 20 mm x 1.8 m length and pole clamps duly erected in provided cement concrete foundation.

Providing pipe type earthing with 20mm Dia GI Pipe rod complete with all material as per specification no. EA-EP. (pole-2 & stay-2)

Supplying and fixing MS base plate 30x30x0.6 cm size fixed to the pole base either by welding or by set screws 12 mm. dia fixed at position.

Supplying & erecting barbed wire two ply with 12 SWG ply and 12 SWG barb with a gap between two bars of 75 mm. firmly fixed on provided angle supports with necessary materials complete. (6.044 meters/One Kilo Gram.).

Making cement concrete foundation including excavation (60 x 60) cm x deep 1/6 of pole length in 1:3:6 cement concrete 20 x 25 mm stone metal, 45 cm x 45 cm x 45 cm /45 cm dia. x 45 cm. height plinth duly plastered, with necessary curing and finishing complete. (for above 9 m poles)

Making cement concrete foundation including excavation (60 x 60 x 150) cm deep in 1:3:6 cement concrete, (20 to 25) mm stone metal with necessary curing and finishing complete.(for stay).

Supplying , erecting & terminating 3 x 300 sq. mm. aluminium 11 kV(E), XLPE armoured cable on wall/ceiling or laid in provided trench / pipe in an approved manner as per specification no. CB-HT (2 run of 700 mtr)

Supplying & erecting G.I. pipe ‘B’ class 150 mm dia. erected for enclosing XLPE armoured cable on wall/pole as per specification.

Providing & erecting epoxy straight through joint outdoor/ indoor for LT XLPE armoured cable 300 sq. mm. cable, with necessary material as per specification no. CB-JT/LT

Providing and erecting Heat shrinkable out door termination kit for 11 kV ( E ) XLPE HT cable 3x240 to 300 sq. mm. with necessary material as per specification no. CB-JT/HT

Supplying & laying (including excavation) 15 cm dia RCC Hume pipe with coupling collar of standard thickness at required depth up to 90 cm below road / ground surface, for enclosing provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet).

Supplying & laying (including excavation) 15 cm dia half round RCC Hume pipe of standard thickness at required depth up to 90 cms. below road / ground surface, for enclosing provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet).

Supplying & erecting inline cut point end pole D. P. structure for 11/0.415 kV, 200 KVA transformer with R.S.J. pole 2 nos. of size 100 x 116 mm x 11 Mtr. long with suitable distribution box of C.R.C.A. sheet 16 SWG with 4 pole MCCB 300 amps as incomer & 6 nos. 100 amps kitkat /MCCB for outgoing circuits. Transformer D.P. structure includes the A. B. switch 200 Amps, D.O. fuse set & L.A. set. 2 nos. Top channel of size 100 mmx 50 mm for erection of A.B. switch & 2 nos. base channel of size 100 mm x 50 x mm for erecting transformer. Channel of size 75 x40 mm for erecting D.O. fuse set, L.A., A.B. switch handle etc. Angle of size 50 x 50 x6 mm for erecting distribution box, transformer belt etc.as per drawing (min.176 One Kilo Gram. iron work ) with necessary clamps, nut-bolts, vee cross arm, top clip, insulators etc. complete with caution board & barbed wire. D.P. Structure shall be erected in c.c. foundation complete.

Supplying, installing, testing & commissioning 3 phase, 11/0.433 kV, 50 Hz., 200 kVA, oil immersed and naturally cooled outdoor type, Alluminium wound transformer, delta/star connected with additional neutral brought out on load side, temperature rise should not exceed 40oC by thermometer in oil and 45oC by the resistance in winding at full load rating, with HV tapping (with off load tap changer) off load +5 to -10 in steps of 2.5%, with standard accessories complete with test certificate with losses below 780 Watts at 50% load, 2300 Watts at 100% load as per IS:1180 - 2014 energy efficiency level II, with necessary permissions of Electrical Inspector, as per specification no SS- TR. (less 35% for Alluminium wound)

Supplying & erecting end pole D. P. Structure for 11/0.415 kV, 100 kVA Transformer with R.S.J. Pole 2 Nos. of size 100 x 116 mm x 11 Mtr. Long with suitable Distribution Box of C.R.C.A. Sheet 16 SWG with 4 Pole MCCB 200 Amps as incomer & 6 Nos.100 Amps Kitkat/MCCB for outgoing circuits. Transformer D.P. Structure includes the A. B. Switch 200 Amps, D.O. fuse Set & L.A. Set. 2 Nos. Top channel of size 100 mm x 50 mm for erection of A.B. Switch & 2 Nos. Base channel of size 100 mm x 50 x mm for erecting Transformer. Channel of size 75 x40 mm for erecting D.O. Fuse Set, L.A., A.B. Switch handle etc. Angle of size 50 x 50 x6 mm for erecting Distribution Box , Transformer Belt etc.as per drawing (min. 124 One Kilo Gram. iron work ) with necessary clamps, Nut-bolts. vee cross arm, top clip, insulators etc. complete with caution board & barbed wire. D.P. Structure shall be erected in c.c. foundation complete.

Supplying, installing, testing & commissioning of 3 phase, 11/0.433 kV, 50 Hz., 100 kVA, oil immersed and naturally cooled outdoor type,Alluminium wound transformer, delta/star connected with additional neutral brought out on load side, temperature rise should not exceed 40oC by thermometer in oil and 45oC by the resistance in winding at full load rating, with HV tapping (with off load tap changer) off load +5 to -10 in steps of 2.5%, with standard accessories complete with test certificate with losses below 475 Watts at 50% load, 1650 Watts at 100% load as per IS:1180 - 2014 energy efficiency level II, with necessary permissions of Electrical Inspector, as per specification no SS- TR. (less 35% for Alluminium wound Rs 3,19,477 - 35%= 207660.05)

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP ( AB, HG, LA-3, Transformer body earthing-4, Toal- 7 x 3 DP= 21 No)

Providing pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.l. Rod complete with all materials as per specification no. EA-EP (3 DP x 2= 6)

Supplying and erecting GI earth wire of high purity of different sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/cable/ conduit with screws in an approved manner.

Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no EA-EP.

Supplying and erecting Three phase smart energy meter DLMS compliance with 3x240V 50 cycles AC supply 10-60 A, ISI mark, accuracy class 1.0 with backlit LCD display, measuring & display V, I, kW, kWh, PF, kVA, kVAr, MD, day, week, month & with communication module configurable for GSM/Wi-Fi, IrDA/Bluetooth, complete provided panel with calibration certificate from manufacturer & duly wired with required size of PVC wires. (2 for 2ooKVA & 1 for 100 KVA)

Supplying and erecting LT current transformer with bar primary 50/5 to 1000/5 ratio with 15 VA burden erected in provided CRCA box duly secured with insulating materials connected to the meter with test certificates. (6 for 2ooKVA & 3 for 100 KVA)

DTC Meter Box- Supplying and erecting metal work in CRCA sheet with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti-rust treatment and duly powder coated or painted with one coat of red lead paint and 2 coats of enamel paint complete) (bottom cable incoming with CT arrangement for meter,Front door glass, size of the glass such that meter reader can easily watch the reading of inside meter as per direction of electrical consultant.) (2 for 2ooKVA & 1 for 100 KVA) (10One Kilo Gram for each meter)

Dismantling the existing pole above 6 m height with brackets, clamps, insulators, stay from the cement concrete foundation and making the site clear by refilling the pits with excavated materials and bringing it to the ground level.

Dismantling the existing overhead line including G.I. wires of all sizes without damaging& making the coils in suitable sizes.

Dismantling existing lightning arrestor set, insulator complete from DP structure in an approved manner.

Dismantling existing pole mounted distribution transformer safely without any damages.

Dismantling the existing cables of all types & size above 50 sq. mm.

Refilling the holes for dismantled cables with cement mortar & finishing in an approved manner etc. complete.

Dismantling the existing underground cable without damaging it with glands, cable end box including refilling the trench up to ground level and making coils complete.

Supplying, erecting &terminating XLPEarmoured cable 1100 V. 3½ core 185 sq. mm. aluminium conductor with continuous 12.97 sq. mm. (8 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (2 run of 200 mtr)

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 160 mm outsidedia, double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete. (for 185 x 2 R-360 mtr cable)

Supplying , erecting & terminating 3 x 300 sq. mm. aluminium 11 kV(E), XLPE armoured cable on wall/ceiling or laid in provided trench / pipe in an approved manner as per specification no. CB-HT (2R X 300)

Providing and erecting Heat shrinkable straight through joint kit for 11 kV ( E ) XLPE HT cable 3x240 to 400 sq. mm. with necessary material as per specification no. CBJT/HT

Providing and erecting Heat shrinkable out door termination kit for 11 kV ( E ) XLPE HT cable 3x240 to 300 sq. mm. with necessary material as per specification no. CB-JT/HT

Supplying & laying (including excavation) 15 cm dia half round RCC Hume pipe of standard thickness at required depth up to 90 cms. below road / ground surface, for enclosing provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet).

Supplying & laying (including excavation) 15 cm dia RCC Hume pipe with coupling collar of standard thickness at required depth up to 90 cm below road / ground surface, for enclosing provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet).

Supplying & erecting G.I. pipe ‘B’ class 150 mm dia. erected for enclosing XLPE armoured cable on wall/pole as per specification.

Supplying & erecting inline cut point end pole D. P. structure for 11/0.415 kV, 200 KVA transformer with R.S.J. pole 2 nos. of size 100 x 116 mm x 11 Mtr. long with suitable distribution box of C.R.C.A. sheet 16 SWG with 4 pole MCCB 300 amps as incomer & 6 nos. 100 amps kitkat /MCCB for outgoing circuits. Transformer D.P. structure includes the A. B. switch 200 Amps, D.O. fuse set & L.A. set. 2 nos. Top channel of size 100 mmx 50 mm for erection of A.B. switch & 2 nos. base channel of size 100 mm x 50 x mm for erecting transformer. Channel of size 75 x40 mm for erecting D.O. fuse set, L.A., A.B. switch handle etc. Angle of size 50 x 50 x6 mm for erecting distribution box, transformer belt etc.as per drawing (min.176 One Kilo Gram. iron work ) with necessary clamps, nut-bolts, vee cross arm, top clip, insulators etc. complete with caution board & barbed wire. D.P. Structure shall be erected in c.c. foundation complete.

Supplying, installing, testing & commissioning 3 phase, 11/0.433 kV, 50 Hz., 200 kVA, oil immersed and naturally cooled outdoor type, Alluminium wound transformer, delta/star connected with additional neutral brought out on load side, temperature rise should not exceed 40oC by thermometer in oil and 45oC by the resistance in winding at full load rating, with HV tapping (with off load tap changer) off load +5 to -10 in steps of 2.5%, with standard accessories complete with test certificate with losses below 780 Watts at 50% load, 2300 Watts at 100% load as per IS:1180 - 2014 energy efficiency level II, with necessary permissions of Electrical Inspector, as per specification no SS- TR. (less 35% for Alluminium wound )

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP ( AB, HG, LA-3, Transformer body earthing-4, Toal- 7 x 3 DP= 21 No)

Providing pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.l. Rod complete with all materials as per specification no. EA-EP (3 DP x 2= 6)

Supplying and erecting GI earth wire of high purity of different sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/cable/ conduit with screws in an approved manner.

Supplying and erecting G.I. strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joint required. as per specification No (EA-EP). (25x5)

MSEDCL SUPERVISSION CHARGES 1.3% (As per MSEDCL estimate 39,173 + 74,522)

Security Deposite and other charges for 4 No CT meter, 1.0 L for each meter)

Security Deposite and other charges for 120 No shop 1-phase meter, 4000.00 for each meter)

Supplying & erecting HMS P.V.C. conduit 25 mm. dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying & laying HMS PVC conduit 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying & erecting HMS P.V.C. conduit 32 mm. dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC..

Supplying & laying HMS PVC conduit 32 mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying and erecting ISI marked modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete. (Total Qty-13 Sr. No. 26)

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 1 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the bacOne Kilo Gramround.. (Total Qty-48 Sr. No. 30)

Supplying & erecting telephone copper cable 2 pair with 0.5mm dia. laid in provided PVC casing capping/ conduit as perspecification No. WG-TW

Supplying & erecting jelly filled unarmoured telephone copper cable 10 pair with 0.5 mm dia. laid in provided PVC casing capping / conduit as per specification No. WG-TW ( Dormitory-10, Main Gate- 220, Sec Gate1- 128, Sec Gate2- 260)

Supplying & erecting jelly filled armouredtelephone coppercable 20 pair with 0.5 mm dia. laid in provided trench as per specification No. WG-TW (main telephone cable)

Supplying, erecting & commissioning MDF Box 60 x 60 pairs as per specification No. WG-TW (main supply, Gate, Dormitory)

Supplying, erecting & commissioning junction box suitable for 20 pairs as per specification No. WG-TW (main cable)

Supplying, erecting & commissioning 10 pair module for connection & disconnection of telephone cable as per specification No. WG-TW (main supply, Gate, Dormitory)

Supplying, installing, testing & commissioning digital (hybrid) type EPABX of 3 x 8 extensions complete. (main Gate-1, Sec Gate-2)

Supplying, installing, testing & commissioning digital (hybrid) type EPABX of 6 x 16 extensions complete. (Dormitory)

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete (for 10 & 20 Pair cable)

Supplying & erecting HMS P.V.C. conduit 25 mm. dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying & laying HMS PVC conduit 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying & erecting HMS P.V.C. conduit 32 mm. dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC..

Supplying & laying HMS PVC conduit 32 mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 1 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the bacOne Kilo Gramround. (Sr No- 29)

Supplying & installing UTP networking cat-6 cable suitable for LAN / WAN Computer net-working as per specification No. WG-COC/NC

Supplying and erecting ISI mark modular type computer jack RJ 45 with safety shutter, duly erected on provided plate and box with wiring connections complete. (Sr No-27)

Supplying and fixing tool-less Information Outlet (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO

Supplying and erecting FR grade, pvcarmoured multimode armoured multimode optical fibre cable with 6 fibres, with core dia 50/125 Lm (OM3) suitable for 1 gbps ethernet distance at 850 nm of wavelength, on wall/ceiling or laid in provided pipe/trench as per specification No. WG-COC/OFC LSZH

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete (for Fibreoptict cable)

Supplying and fixing rack mounted type 12 Ports, light guide unloaded interconnect unit with adapter panel for termination of optical fibre cables on wall/ provided U rack complete as per specification no. WG-NAS/ LIU (Dormitory-1, Main gate-1, Sec gate-2)

Supplying and fixing 1 meter length, UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Supplying and fixing 3 meter length, UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Supplying, fixing, and configuring web smart power over ethernet switch of 24 ports on provided rack or as directed as per specification No. WG-NWC/ENS

Supplying, fixing, and configuring broadband ADSL router with all accessories, on provided rack or as directed as per specification No. WG-NWC/ADSL

Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP

Supplying and fixing 9U wall mount rack (Dimension-DxWxH – 450x550x500 mm) as per specification No. WG-NAS/RAK

Supplying and fixing manageable wireless dual-band 802.11 n/ac unified wireless access point in WLAN network as per specification no. WG NAS/LAP1

Supplying, fixing, and configuring managed gigabit switches 48 Ports 10/100/1000Mbps + 4 SFP Ports complete.

Supplying & erecting on line UPS pure sine wave of 1 kVA capacity complete with standard features, along with necessary SMF batteries for 30 mins. battery backup, as per specification no. AP-UPS (main Gate-1, Sec Gate-2)

Supplying & erecting on line UPS pure sine wave of 10 kVA capacity complete with standard features, along with necessary SMF batteries for 30 mins battery backup, as per specification no. AP-UPS (Dormitory-1 for EPABX, LAN & CCTV)

Supplying, fixing, and configuring broadband ADSL router with all accessories, on provided rack or as directed as per specification No. WG-NWC/ADSL (Dormitory-8 for WiFi, Gate-3)

Supplying, erecting, testing and commissioning amplifier 120 W for public address system suitable to operate on 230 Volts A.C. / 12 Volts D.C. supply complete as per specification no. FF-PA/AFR (DORMITORY-1, MUSEUM-1, STAGE-1)

Supplying, erecting, testing and commissioning sound column 15 Watts complete as per specification no. FF-PA/SOC (Dormitoey GR-11, 1st-11, 2nd-20, 3rd-20, Museum-4, Stage-8)

Supplying, erecting, testing and commissioning microphone complete as per specification no. FF-PA/MIC

Supplying, erecting, testing and commissioning stand for microphone complete.

Supplying, erecting, testing and commissioning table stand for microphone complete.

Supplying, erecting, testing and commissioning of 2 core shielded microphone cable complete as per specification no. FF-PA/MCC

Supplying, erecting, testing and commissioning of 0.75 sq mm speaker wire complete.

Supplying & erecting HMS P.V.C. conduit 25 mm. dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying & laying HMS PVC conduit 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying & erecting HMS P.V.C. conduit 32 mm. dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC..

Supplying & laying HMS PVC conduit 32 mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying & erecting H.M.S. P.V.C. conduit 20 mm. dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying & laying HMS PVC conduit 20 mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying & erecting HMS P.V.C. conduit 25 mm. dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying & laying HMS PVC conduit 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying & erecting HMS P.V.C. conduit 32 mm. dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying & laying HMS PVC conduit 32mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying and fixing power over ethernet adaptor to provide DC supply to Ethernet devices as per specification No. WG- NAS/PEA ((Dormitory-1, Museum-1, Stage-1, Main gate-1, Sec Gate-2)

Supplying and fixing 6U wall mount rack (Dimension-DxWxH – 450x550x367 mm) as per specification No. WG-NAS/RAK For Ground Floor - 1

Supplying, fixing, and configuring 8-ports 10/ 100/ 1000Mbps unmanaged gigabit PoE Switch complete.

Supplying, Installation, Testing &Comissioning of 2MP IP fixed Dome Camera: 1/2.8'' progressive scan CMOS, Max resolition 1920 x1080x @ 25/30 fbs, 4/6 mm Fixed lens, Colour: 0.01 lux @ (F1.2, AGC ON) ONVIF, support H.265+, H.265, H.265+, 3 stream ANR, 120dB wide Dynamic Range BLC, HLC, 12 VDC & Poe (802.3af), IR range: 40m supporton-board storage upto 128GB (SD card not oncluded), IP67, Line crossing detection, face detection, object removal, Unattendant baggage removal scene change detection certificate - CE, FCC, UL

Supplying, Installation, Testing &Comissioning of 2MP IP fixed Bullete Camera: 1/2.8'' progressive scan CMOS, Max resolition 1920 x1080x @ 25/30 fbs, 4/6 mm Fixed lens, Colour: 0.01 lux @ (F1.2, AGC ON) ONVIF, support H.265+, H.265, H.265+, 3 stream ANR, 120dB wide Dynamic Range BLC, HLC, 12 VDC & Poe (802.3af), IR range: 40m supporton-board storage upto 128GB (SD card not oncluded), IP67, Line crossing detection, face detection, object removal, Unattendant baggage removal scene change detection certificate - CE, FCC, UL

NVR-64 Channel (8SATA Support). Supply, installation, testing and commissioning of 64 Ch smart network High performance video recorder. Connectable to the third party network cameras upto 64 IP cameras can be connected, Lumix OS upto 12 MP resolution two independent HDMI/ VGA output, supprot h.265/MJPEG, incoming bandwitdh 320Mbps, 8 SATA HD ANR technology 8 SATA interface or more for 8HDDs and capacity of each HDD upto 10TB, N+1, hot spare system Support HDD hot swap with RADIO, RAID5 RADI6 and RAID10 storage scheme configuration with redundend power supply front panel: 1 x 4510/1000/1000 Mbps self-adoptive enthernet, interface, multiple networking monitoring. (for external cameras control)

Supply, installation, testing & commissioning of NVR 32 Channel H.264+ /H.265/ H.264 +/ MPEG4 video formates, incomming/ outging Bandwidth 256 Mbps, Connectable to the third party network cameras. Centralized management of IP cameras, including configuration, information import/ exports, real time information display, two-way audio, upgrade etc. Upto 32 IP cameras can be connect recording at upto 8 MP resolution . 4 sata support Each support 6TB HDD. Supportss live view storage and playback of the connected cameras at up to 8MP resolution HDMI and VGA independent outputs provided, instant playback for assigned channel during multi channel display mode. (Dormitory)

Supply, installation, testing & commissioning of 8 TB internal Hard disk for SATA port of NVRwith accessories.

Supplying erecting testing and commissioning 43'' (108cm) LED TV with full HD display smart TV with accessoreis.

Supplying & installing UTP networking cat-6 cable suitable for LAN / WAN Computer net-working as per specification No. WG-COC/NC

Supplying & installing UTP networking cat-6 armoured cable suitable for LAN / WAN Computer net-working as per specification No. WG-COC/NC

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete (for CCTV cable)

Providing & erecting 4 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no.OH-PL/OPL (for CCTV)

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation, fixing provided nut bolts with the help of template, duly plastered as per design complete (for 3 to 5m octagonal / conical GI pole)

Supplying, erecting, testing and commissioning 16 HP, VRF / VRV air conditioning system, out door unit (ODU) complying type-IV OEM standards working on HFC free refrigerant R410A or other required/suitable green equivalent refrigerant, for cooling capacity delivering 100% at 47 deg. celcius and non stop cooling even at 56 deg. celsius and coefficient of performance (COP) 3.00 to 4.00, modular type horizontal/vertical hot air discharge suitable for total piping length upto 1000 metre operation in cooling mode with inverter based VRF/VRV technology microprocessor based control compressor starter/control panel complete with scroll compressor, air cooled anti corrosive copper condenser coil of suitable shape for increasing maximum heat transfer area, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V ± 10%, 50 Hz, 3 phase power supply, internal copper refrigerant piping, internal wiring and first charge of refrigerant, etc. all housed in powder coated weather proof cabinet on provided angle iron frame or suitable foundation connected to the system in approved manner complete.VRF Indoor Units Wall Mounted Type Indoor Units

Supply, installation, testing and commissioning of VRF/VRV based Hi-wall type indoor unit (IDU) of nominal cooling capacity 1.8TR (594 cfm) to 2.2TR (655 cfm) having EER as per BEE standards and specifications with multiple speed evaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, expansion device, cordless remote control with necessary controls, with 3-core copper flexible cord of required length and electrical terminal to receive power supply, etc. IDU shall have anti-corrosive coating suitable for coastal area. Unit shall be suitable for indoor wall mounting, having an electronic control console, provided with suitable mounting brackets with any additional refrigerant and oil charge as per the requirement during installation, connected to the system complete.

Supplying, erecting, testing and commissioning centralised programmable remote contol panel (HMI) touch manager controls minimum 16 system of minimum 64 ODU's can be controlled and up to 992 IDU's can be individually mounted and controlled indoor units having minimum 200 mm size colour LCD touch panel, yearly schedule, power proportional distribution function, temperature limitation, history function complete erected on wall with an arrangement to integrate with provided fire alarm system.

Supplying and installation of high pressure grade required size copper connection Y or T- Joints / refnet for liquid and suction line complete erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc. with brazing and testing for leakages confirming the normal operation of the VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 41.3 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquidmain line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV /VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 34.9 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquidmain line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along withapplication of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 28.6 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquidmain line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulationof 19 mm thick elastomeric nitrile rubber along withapplication of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 22.2 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquidmain line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulationof 19 mm thick elastomeric nitrile rubber along withapplication of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 19.1 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquidmain line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulationof 19 mm thick elastomeric nitrile rubber along withapplication of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 15.9 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquidmain line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulationof 19 mm thick elastomeric nitrile rubber along withapplication of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 12.7 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquidmain line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulationof 19 mm thick elastomeric nitrile rubber along withapplication of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 9.5 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquidmain line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulationof 19 mm thick elastomeric nitrile rubber along withapplication of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 6.4 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquidmain line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulationof 19 mm thick elastomeric nitrile rubber along withapplication of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supply, Installation, Testing and Commissioning of drain piping conformimg to IS :1239 /3589 heavy class inculding all fitting like anchor fasteners , pipe supporting , frame structure , coupling , bends, elbows, tees, flanges, tappings, wall sleeves, hangers and rigid polyurethane foam block etc. Pipe should be insulated with 9 mm thick EPDM rubber with adhesive. 25 mm Dia

Supply, Installation, Testing and Commissioning of drain piping conformimg to IS :1239 /3589 heavy class inculding all fitting like anchor fasteners , pipe supporting , frame structure , coupling , bends, elbows, tees, flanges, tappings, wall sleeves, hangers and rigid polyurethane foam block etc. Pipe should be insulated with 9 mm thick EPDM rubber with adhesive.32 mm Dia

Supplying and erecting GI sheet 1.25 mm (18 SWG) to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint.

Supplying and erecting GI sheet 1 mm (20 SWG) to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint.

Supplying and erecting GI sheet 0.8 mm (22 SWG) to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint.

Supplying and erecting GI sheet 0.6 mm (24 SWG) to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint.

Providing adhesive thermal insulation for supply / return air duct with 19 mm nitrile rubber insulation having R-value as per the prevailing provisions in ECBC-2007.

Supplying and erecting aluminium powder coated linear grill of suitable size for width length without collar dampers having matching colour with the existing false ceiling and suitable for deflection of 15/30/45 degree

Supply, fabrication, installation an testing of flexible canvass connections constructed between ductable unit / dampers / ducting of required size with fire resist flexible double canvas sleeve complete.

Supplying & erecting 22 SWG G.I sheet metal cawl sector shaped with 25 x 25 x 3 (mm) angle iron frame, metal mesh to avoid birds entry with necessary material, suitable for exhaust fan of 450 mm

Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority

Providing vaccumising the airconditioner system to 200 micron and charging with R-410A/R32 refrigerant for air conditioning unit. Approved Make DUEPOINT/ HONEYWELL

Providing & erecting Hot dipped galvanized ladder type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 500 mm width & 100 mm height comprising all required standard accessories.

Providing & erecting Hot dipped galvanized cover suitable for perforated type cable tray manufactured from 18 swg (1.2 mm thick) GI sheet of 500 mm width & 20 mm height complete with necessary hardware in approved manner.

Supply & Installation of cables for Indoor, Outdoor & Electrical control panel complerewith control cabling, ISI marked Only. Main Electrical supply upto Control Electrical panel / outdoor machine.3 C X 2.5 sq. mm copper arm

Supply & Installation of cables for Indoor, Outdoor & Electrical control panel complerewith control cabling, ISI marked Only. Main Electrical supply upto Control Electrical panel / outdoor machine.4 C X 6 sq. mm copper arm

Supply & Installation of cables for Indoor, Outdoor & Electrical control panel complerewith control cabling, ISI marked Only. Main Electrical supply upto Control Electrical panel / outdoor machine.3 C x 2.5 sq. mm copper

Supply & Installation of cables for Indoor, Outdoor & Electrical control panel complerewith control cabling, ISI marked Only. Main Electrical supply upto Control Electrical panel / outdoor machine.4 C x 4 sq. mm copper

Carrying out core cutting of size 3" to 5" dia x 15" length in the C.C./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original.

Supply of floor Mounted type Evaporative Air Cooler unit fabricated out of extruded aluminium section with 0.6mm pre-plasticized/ pre-coated Galvanised steel sheet outside & 0.6 mm plain Galvanised steel sheet inside with blower, blower section and blower motor suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, belt drive package, wet section & tank. The Evaporative Air Cooler unit shall be complete with water circulation pump, interconnecting piping & valves. The Evaporative Air Cooler unit with 30mm static. (10000 CFM)

Supply of floor Mounted type Evaporative Air Cooler unit fabricated out of extruded aluminium section with 0.6mm pre-plasticized/ pre-coated Galvanised steel sheet outside & 0.6 mm plain Galvanised steel sheet inside with blower, blower section and blower motor suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, belt drive package, wet section & tank. The Evaporative Air Cooler unit shall be complete with water circulation pump, interconnecting piping & valves. The Evaporative Air Cooler unit with 30mm static. (15000 CFM)

Supply of HVLS fan for proper ventilation of following capacity:

Supply, installation, testing and commissioning of factory fabricated ESP Dry type Scrubber unit ceiling suspended type fabricated out of extruded aluminium section with pre-plasticized /pre-coated Galvanised steel sheet outside & plain Galvanised steel sheet inside with blower, blower section and blower motor TEFC type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, belt drive package. The scrubber shall be of following capacity (Kitchen - 10000 CFM)

Supply, installation, testing and commissioning of factory fabricated ESP Dry type Scrubber unit ceiling suspended type fabricated out of extruded aluminium section with pre-plasticized /pre-coated Galvanised steel sheet outside & plain Galvanised steel sheet inside with blower, blower section and blower motor TEFC type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, belt drive package. The scrubber shall be of following capacity.(Kitchen - 15000 CFM)

Entire exhaust is made of S.S-304 Sheet. Fitted with grease collection tray and hang with metal fasteners.

Supply & installation of Disc Valve for Toilet Exhaust systems (150 mm dia)

Supply & installation of 15 mm thick Nitril Rubber

Supply & installation of 15 mm thick N-CLAD required for terrace floor.

Carrying out core cutting of size 3" to 5" dia x 15" length in the C.C./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original.

Providing Round bottom fire bucket of 9 Litres capacity as per IS : 2546 made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside and red outside with FIRE Mark, on provided stand/ wall hook complete.

Providing Floor mounting stand for keeping 4 Nos. of FIRE buckets 1500mm in length, 900mm in height frame made out of 30x30x4 mm angle iron with cross supports for legs, welded with 4 hooks and duly painted with one coat of red lead and two coats of silver paint complete.

Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 One Kilo Gram. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts grouted in wall complete.

Supplying and erecting ABC powder type fire extinguisher as per IS : 13849 /15683 of 6 One Kilo Gram capacity with necessary clamp for erection on wall.

Supplying, installing, testing and commissioning with perfect aligning, proper levelling of fire service main single stage pump, of 2400 LPM at 76 m head centrifugal type, 75 HP (55 kW) 3 phase, 415 volt, 50Hz or of suitable HP complete as per specification no. FF-MFP/SSC

Supplying, installing, testing and commissioning with perfect aligning, proper levelling of jockey pump of 240 LPM at 105 m head 20 HP (15 kW), 3 phase, 415 volt, 50Hz or of suitable HP with suitable stages as per specification no. FF-MFP/JP

Supply, installation, testing & commissioning of diesel engine drive common stand by pump horizontl centrifugal end suction backpull out type with gland packing and capable to deliver 137 Cum/hr(2280lpm) at 70 mwc confirming to IS 5120-1977.The pump shall be coupled to suitable HP diesel engine with speed of 2100 RPM and for Discharge 1620 LPM at 45 mtr head and complete set shall be mounted on common base frame.Batteries& battery leads withstand, fuel tank with stand( for 6 hrs. oprationsApprx), fuel piping with valves, coupling guard, and other standard accessories, and foundation bolts, etc. complete.Make- KBL/Kirlosker/wilo/Lubi/CRI (Rates are as per sanct. Estt. 45/BLD/EE/2019-20), Non CSR.

CUBICAL FIRE PANEL FOR PUMP: Fabricating supplyng testing and commissioning of electrical control panel of cubical construction, floor mounted type fabricated out of 2mm thick crca sheet, compartmentalized and hinged lockable doors, dust and varmin proof powder coated approved shade, cable alley interconnection, having switchgears andaccessories mounting and internal wiring,earh terminals, numbering etc. complete in allrespect suitable for operation on 415v, 3 phase 50 hz,Ac supply with enclosure protection class IP-42 as required. ( The Detail of Panel Shall approved as per pump load)

Supplying, installing, testing and commissioning with perfect aligning, proper levelling of booster pump of 180 LPM at 40 m Head, 5 HP (3.75 KW), 3 phase, 415 volt, 50Hz or of suitable HP with suitable stages as per specification no. FF-MFP/BP

Supplying and erecting G.I. pipe above ground of ‘C’ class ERW of size 25 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting ISI mark GI pipe 32 mm. dia ‘C” class at position with accessories complete. Specification no. CW-PLB/GP.

Supplying and erecting ISI mark GI pipe 40 mm. dia ‘C” class at position with accessories complete. Specification no. CW-PLB/GP.

Supplying and erecting G.I. pipe above ground of ‘C’ class ERW of size 50 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe above ground of ‘C’ class ERW of size 65 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe above ground of ‘C’ class ERW of size 75/80 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe above ground of ‘C’ class ERW of size 100 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe above ground of ‘C’ class ERW of size 150 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe above ground of ‘C’ class ERW of size 200 mm dia with necessary fittings complete as per specification no. FF-PP

Providing coating of bitumen paint & 4mm thick wrapping for underground 150 mm ring main of fire fighting system.

Supplying and erecting cast iron foot valve ball type/flap type of size 100 mm dia with strainer for negative suction complete as per specification no. FF-VL/FV

Supplying and erecting cast iron foot valve ball type/flap type of size 150 mm dia with strainer for negative suction complete as per specification no. FF-VL/FV

Supplying and erecting cast iron foot valve ball type/flap type of size 200 mm dia with strainer for negative suction complete as per specification no. FF-VL/FV

Supplying and erecting 100 mm dia end line strainer for positive suction complete as per specification no. FF-VL/ELS

Supplying and erecting 150 mm dia end line strainer for positive suction complete as per specification no. FF-VL/ELS

Supplying & erecting cast iron double flange butterfly valve of size 50 mm dia. complete as per specification no. FF-VL/BFV

Supplying & erecting cast iron double flange butterfly valve of size 75/80 mm dia. complete as per specification no. FF-VL/BFV

Supplying & erecting cast iron double flange butterfly valve of size 100 mm dia. complete as per specification no. FF-VL/BFV

Supplying & erecting cast iron double flange butterfly valve of size 150 mm dia. complete as per specification no. FF-VL/BFV

Supplying & erecting cast iron double flange butterfly valve of size 200 mm dia. complete as per specification no. FF-VL/BFV

Supplying and erecting cast iron double flange NRV of size 75/80 mm dia complete as per specification no. FF-VL/NRV

Supplying and erecting cast iron double flange NRV of size 100 mm dia complete as per specification no. FF-VL/NRV

Supplying and erecting cast iron double flange NRV of size 150 mm dia complete as per specification no. FF-VL/NRV

Supplying and erecting gun metal single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV

Supplying and erecting stainless steel double outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV

Supplying & installing one piece moulded HDPE / fibre water tank for negative suction only, having capacity 1000 litres fitted with necessary accessories complete as per specification no. FF-FFA/PT

Supplying and installing wall mounting swinging Hose reel drum fitted with 19 mm dia. 30m long high pressure polypropylene (Polyhose) fitted with necessary accessories complete as per specification no. FF-FFA/HV

Supplying fire fighting reinforced rubber lined (R.R.L.) hose pipe, 63mm dia, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL

Supplying & erecting stainless steel branch pipe 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specifications no. FF-FFA/NZ

Supplying and erecting fire brigade header of 150 mm dia, for supplying water in fire tank complete as per specification no. FFFA/ FBC

Supplying and erecting fire brigade header (Siamese connection) of 150 mm dia for supplying water to wet riser system complete as per specification no. FF-FFA/SMC

Supplying and installing air vessel of 300 mm dia 1.5m in height M.S. tank installed inside pump house / on terrace complete as per specification no. FF-FFA/ACT

Supplying and erecting 20/25mm dia gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARV

Supplying and installing pressure gauge of 100 mm dia., 0-300 PSI or 0-14 One Kilo Gram per cm square fitted with 12/15 mm dia. pad cock valve, and G.I. pipe, elbow etc. complete as per specification no. FFFFA/ PG

Supplying and installing pressure switch with 12/15 mm dia isolation valve, G.I. nipple, elbow, etc complete as per specification no. FF-FFA/PS

Supplying and erecting one no. brass orifice plate having 6 mm. thickness, 140 mm outer dia and required/proper diameter of inner hole at every single outlet hydrant valve as per specification no. FF-FFA/OP

Supplying and erecting M.S./CRCA cabinet for housing single hydrant valve (size 400 x 400 x 400mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8"x6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour.

Supplying and erecting M.S./CRCA cabinet for housing Fire Brigade / SIEMESE connections (size 1250 x 400 x 300 mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8" x 6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour.

Supplying, installing, testing and commissioning heat detector complete on box as per specification no. FF-FAS/HD

Supplying, installing, testing and commissioning optical type smoke detector complete on box as per specification no. FFFAS/SD

Supplying, installing, testing and commissioning manual call point (Pill box) with break glass push button in metal enclosure complete as per specification no. FF-FAAS/MCP

Supplying, installing, testing and commissioning hooters with CRCA enclosure complete as per specification no. FF-FAAS/HTR

Supplying, installing, testing and commissioning FR, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CBLT/ CU

Supplying, installing, testing and commissioning of 2 Zones Microprocessor based conventional fire alarm control panel (FACP) with standard accessories complete as per specification no. FF-FAAS/FACP

Supplying, erecting, testing and commissioning of 15 mm (½") dia. NBCM Body chrome finished quartzoid bulb sprinkler having 68º C fixed temperature rating with deflector disc of conventional construction complete as per specification no. FF-SPR

Supplying and erecting of 120 minutes fire rated hinged metal fire door 1200mm X 2100mm as per BS:476 Part-22 & IS:3614 Part-II rated uninsulated single 50mm thick with honeycomb infill of frame thickness 1.6mm and shutter thickness 1.2mm powder coated with all fixtures.

Supply, installation, testing and commissioning of fire exit signages of photolumincient type with standard accessories complete.Fire Signage Board (Autoglove)

Supply and erection of emergency start / stop push button station weather proof type for Booster pump at terrace level.

Supplying and fixing of G.I. cable tray 100x50 withneccessory angle iron suspension supports, anchor fasteners etc. complete. Maximum height of suspension shall not exceed 500 mm. size of the tray shall be suitable for laying the above mentioned cables.

Supplying and fixing of G.I. cable tray 50 x 50 with neccessory angle iron suspension supports, anchor fasteners etc. complete. Maximum height of suspension shall not exceed 500 mm. size of the tray shall be suitable for laying the above mentioned cables.

Supplying, erecting &terminating XLPEarmoured cable 3½ core 50 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL for main pump

Supplying, erecting & terminating XLPE armoured cable 4 core 4 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU for jockey pump

Supplying, erecting & terminating XLPE armoured cable 4 core 6 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU Fire Booster pump

Supplying, erecting & terminating XLPE armoured cable 2 core 2.5 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU for instrumentation

GI earthing strips of 25mm x 3 mm thick , strip shall be run on floor /celling / walls, from the equipement to the nearest earth pit with neccessory accessories as required . (Earth pit shall be executed by other agencies).

Providing M.S. supports in angle iron / plates rods etc. as per the instruction at site. Rate quoted shall include for supply and providing necessary, welding cutting, 'U' clamps both nuts, washers etc. as per specification or pipe supports for horizontal / vertical pipes running along wall / column, slabs trenches etc to suit different dia pipes.

Providing M.S. supports in angle iron / plates rods etc. as per the instruction at site. Rate quoted shall include for supply and providing necessary, welding cutting, 'U' clamps both nuts, washers etc. as per specification or pipe supports for horizontal / vertical pipes running along wall / column, slabs trenches etc to suit different dia pipes.

Supplying, installing, testing, and commissioning of flow switch 100mm dia.on sprinkler distribution lines of following as per locations marked in the single line daigram. End shall be connected to fire alarm panel through cable. Cable shall be measured seperately.

Supply, installation, testing and commissioning of high tech support comprising of GI suspension rod with anchor fastener, threaded at both ends with supporting arrangement for sprinkler piping of various diameters , complete in all respect.

Supply and installation of Mechanical foam type 50 lit Capacity Fire Extinguisher, inside cartridge type fitted with Gun Metal cap, high pressure discharge hose with Nozzle, trolley mounted will be coupled with Co2 Cylinder externally (expellant), painted Fire red, It shall Also be provided with safety valve and drain The equipment will be supplied with initial charge of Dry Chemical Powder confirming to IS 4308, bearing ISI Mark The Extinguisher is as per IS 10658, specification bearing ISI. Mark.

Supply, installation and testing of stainless steel corrugated flexible pipe (hose) for dropping sprinklers below false ceiling ,pipe shall be 16 bar pressure rating and 1000mm long 25mm dia with union /reducer collar,clamps etc. as required.

Supplying, installing, testing and commissioning of 20 kWp capacity on grid solar power pack with GI mounting structure and inter connecting wires / cables without battery bank SPV modules and solar power conditioning unit of required capacity complete, with 5 years on site performance warrantee. Specification no. ESD-RT- ONG ( for 11KWP -398096 AND 36190 x 9 KWp= 3,25,710.00) (Total Capacity- 20KVA =11+9)

Supplying, installation & marking of surge arrestor / surge protection device at the main distribution board after the incoming breaker of type 1+2 tested for Imax 100 kA for three phase and neutral as per specification no. CP-SPD

Supplying and erecting AC three phase HT CT multifunction net meter DLMS compliance of accuracy class 0.5, 3x 63.5V, 50Hz, with backlit LCD display, optical port & RS 232 port( measures import kWh, kVAh, export kWh, kVAh, net kWh, kVAh, V, I, kW, 6 months history of energy, load survey, TOD, tamper detection & logging, power ON/OFF events, instantaneous parameters of rating 1/5A with display in absence of power) with wiring connections and mounting hardware on provided panels complete with calibration certificate from manufacturer.

Supplying, installing, testing and commissioning of ETC solar water heating system with heat exchanger type of 500 LPD capacity complete. Specification no. ESD-SHWS-ETC (Dormitory Building- 30 Ltr for each person @200 Person- 6000 Ltr= 12 No of 500 LPD) (Toilet Block 30 Ltr for each person @200 Person- 6000 Ltr= 12 No of 500 LPD) (60210 + 15%(9031.50)= 69241.50)

Supplying and erecting 16/20 mm (ID/OD) polyethylene composite pipe duly joined by compression/crimp fitted accessories, with internal as well as external end sealing arrangement for solar water heater system complete. Specification no. (ESD-HWP/PCP)

Supplying and erecting 20/25 mm (ID/OD) polyethylene composite pipe duly joined by compression/crimp fitted accessories, with internal as well as external end sealing arrangement for solar water heater system complete. Specification no. (ESD-HWP/PCP)

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for over coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 19 mm for solar water heater system.

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for over coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 22 mm for solar water heater system.

Providing and fixing high-density polyethylene (HDPE) container one piece moulded water tank made out of high density polyethylene and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow pipe inclusive of all tanks capacity up to 20000 litres.

Sand i) Fineness Modulus ( Sieve Analysis ),Silt & Clay Content ii) Chloride & Sulphate Content. III) Silt Factor.

HB Metal -Water Absorption, Specific Gravity,Impact Value, Crushing Value.

CB Metal for Concrete Water Absorption, Specific Gravity,Impact Value, Crushing Value.

Concrete Mix Design (With all Tests on basic materials)

Cement laborortorytest of Cement for Standard Consistancy Fineness, Specific Gravity, Setting Time ( Initial & Final ), Compressive Strength, Soundness

Steel Upto 16 mm (set of 3 bars) (Tensile strength, %, Elongation, Yield Stress,Weight-Per Meter, Bend / Rebend Test, Proof Stress.)

Above 16 mm (set of 3 bars) (Tensile strength, %, Elongation, Yield Stress,Weight-Per Meter, Bend / Rebend Test, Proof Stress.)

Bricks Water Absorption (Set of 5 Bricks), Compressive Strength( Set of 5 Bricks), Efflorescence (Set of 5 Bricks).

Vetrified Tiles Water Absorption, Modulus of Rupture (Set of 6 Tiles)

Ceramic Tiles Water Absorption, Modulus of Rupture (Set of 6 Tiles)

Concrete paving block Compressive Strength , Water Absorption,(Set of 8 Blocks)

Murum 1. Sieve Analysis. 2. Liquid limit & plastic Limit.

CC Cubes for Compresenive Srength

Roylty Charges of Sand

Roylty Charges of Minerals

Providing Services of Experience holder engineer (minimum Diploma holder in civil engineering & two years experiance) to work at the office of the Sub Divisional Engineer & Site as directed by engineer in charge

Providing Services of Experience holder Technician (minimum ITI & two years experiance) to work at the office of the Sub Divisional Engineer & Site as directed by engineer in charge

Providing Services of Experience holder Computer Typist (minimum Typing 30/40, MSCIT & having good command on Autocad with two years experience ) to work at the office of the Sub Divisional Engineer as directed by engineer in charge

Harsh Constructions Pvt Ltd