SPECIAL REPAIR TO BLDG NO T-709 (MI ROOM) AND T-710 (TRG CELL) AT LGJ MIL STN

Amount

Demolition of brickwork or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles including cleaning and stacking serviceable brick for re use and balance removing rubbish from the site complete all as specified and as directed by Engineer-in-charge.

M&L for old size brick work with sub class 'B' bricks straight or curved any radius built in cement mortar (1:4) all as specified & directed.

Dismantling asbestos cement (corrugated / semi corrugated) sheets including ridges as in roof covering all as specified & directed.

S & F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling timber scantings (unframed work) in fillets, rails, posts, rafters, purlins etc under 40 Sq cm in, section complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

S&F Roof trusses (framed) , trussed , purlines, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or Flat section) including distance pieces , cleats etc Fe-290 (Gde E-165) complete all as specified and directed by Engr-in-charge.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying a coat of red oxide zinc chrome primer and two coats of synthetic enamel paint (for steel surfaces) including preparation of surface complete all as specified.

M&L for preparation of old painted surfaces including as knotting, stopping, Burning off or removing, scraping etc,and then applying one coat of synthetic enamel paint (ordinary tint) on steel surfaces over 10cm width or girth complete all as specified and directed by Engineer - in - Charge.

Dismantiling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed by Engineer-in-charge.

Supply only Galvanised mild steel plain wire 4 mm thick for hanging purpose of ceiling frame complete all as specified and directed by Engineer-in-charge.

Supply & fixing anodized aluminium snap grid framework for false ceiling, size of snap grid frame work 605 mm x 605 mm with alluminium angle of 25 x 25 x 1 mm, main 'T' of 38 x 25 x 1.5 mm and secondary 'T' of 25 x 25 x 1 mm complete all as specified and as directed by Engineer in Charge .

M & L for 4 mm thick non asbestos cement 'E' board fibre building boards, fixed or laid/inserted to timber/GI/Aluminium frame work with screws complete all as specified and as directed by Engineer in Charge .

Taking down cement plaster/terrazoo on brick/stone wall or concrete surfaces or ceiling including raking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick on brickwork or concrete surfaces in cement mortar 1:6 on wall, finished fair even and smooth without using extra cement all as specified and directed.

M&L Prepration of New plastered External wall surface and applying the following :- (a) M&L wall care putty 1 mm thick on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified. (b) M&L two coat of Exterior Acrylic emulsion(weather coat) over a coat of primer priming by using Airless spray / Roller over complete all as specified Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-charge in case of places where using of Mechanical equiment are not posiible

Material and labour for complete removal of existing treatment of painted wall/ceilling incl pillar etc by mechanically means such as electrical grinder any description by mechanically means such as electrical grinder and applying two coat of 100% Premium weather proof exterior acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed by Engineer-in- charge.

M&L for rendering 15mm thick in cement mortar 1:6 on other than fare face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L Prepration of New plastered Internal wall surface and applying the following :- (a) M&L wall care putty 1 mm thick on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified (b) M&L two coat of internal acrylic emultion over a coat of primer priming by using Airless spray / Roller over complete all as specified Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-charge in case of places where using of Mechanical equiment are not posiible

M & L for preparation of old surfaces by complete removal of existing treatment of painted ceiling incl beams etc. by mechanical equipments like electric wall sander/water jet machine and applying cement based putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and applying two coat of distemper with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour over a coat of alkali resistant primer complete, by mechanical means as per manufacturer's specification all as specified and as directed by GE.

M&L PCC 1:2:4 type B-1, using 20mm graded stone aggregate as in roof kerbs or mud stops, and like rounded or chamfered on edges including necessary form work etc complete all as specified and directed by Engr-in-Charge.

Cutting out cracks to V-section in exisitng roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer - in - Charge.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10 mm wide, 30 mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as directed.

M&L for 100mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base below floors all specified and directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compa ction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed by Engr-in-charge.

M&L for precast cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in kerb stones of size 300 mm x 300 mm x 100 mm with plain fair faces, including chamfers, weathering, throating etc setting in CM 1:4 complete all as specified and directed.

M & L for surface plain or moulded, n. exc 10 cm width or girth when uncoinnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint complete all as specified and directed.

Supply & fixing HDHMR Board , 18/19mm thick both side decorative laminated, density over 850kg/cum, having a class A fire rating, grade 2 quality, interior grade, including continuous SS (304 grade) piano hinges with width of flap 30 mm, with lock and locking arrangement , stainless steel (304 grade) finished Handle 200 mm long-01 No on each shulter , L bend or necessary fittings to mount on wall or to frame work as in Kitchen cup board Shutter / shelves / cabinet etc complete all as per direction of Engineer- in-Charge Note : All exposed edges/surfaces to be finished with same laminated sheet to match with the other surfaces and noting will be paid extra. Design and pattern will be finalized as per site reqmt complete all as specified and directed.

Supply & fixing steel soft close hinge with 35 mm cup dia ful overlay 110 degree opening suitable for 18 mm thick shutter complete all as specified and as directed by Engineer-in-charge .

S & F gun metal handle of size 150 mm for cuboards/shutters fixed with screws complete all as specified and as directed by Engineer-in-charge .

S & F magnetic closer of suitable size for cuboards fixed with steel screws complete all as specified and as directed by Engineer-in-charge .

S & F Hasp and staple 75 mm mild steel, wire type, stove enamelled back including bolt to hinge plate and fixed screws as approved by Engineer-in-charge .

S & F lock for cup boards with two type keys and hole cover (silver painted finish) fixed with screws complete all as specified and as directed by Engineer-in-charge .

Material & Labour for mild steel work conforming to Fe-290 (E-165) as in grills, gratings etc. with ends of bars shouldered and/ or rivetted or forged into spikes; framed guard bars, walkways, railing, framed work of water tanks and similar works complete all as directed by Engineer-in- charge

Taking down chowkhats or frames n.exc 1.5 sq. m each with shutters (without taking off shutters from the frame) complete all specified and directed directed.

Taking down chowkhats or frames exc 1.5 sq. m but n.exc 4.0 sq. m each with shutters (without taking off shutters from the frame) complete all specified and directed directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately)

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately)

S&F for Factory made single extruded WPC (Wood PolymerComposite) solid plain flush door shutter of 35 mm thick size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. including supply and fixing following items :- (a) Stainless steel (304 Grade) Finished butt Hinges 100 mm, 4 Nos per leaf and table 6 of BIS 12817-2020 BIS Marked. (b) Stainless stell (304 Grade) finished square tower bold 200 mm long-2 Nos per leaf as per table 01 dia of bolt 12 mm as per BIS 12833. (c) Stainless steel (304 Grade) Finished Handles 200 mm-2 Nos per leaf. (d) Stainless steel (304 Grad) finished siliding bold 300 mm-1 No per leaf, 16 mm dia as per BIS clause (iii) of BIS 15834-2020. (e) Stainless steel (304 Grade) Finished Floor door stoper-1 Nos per leaf.

S&F for Factory made single extruded WPC (Wood Polymer Composite) glazed and skeleton plain door shutter of 35 mm thick size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Including supply and fixing of stainless steel 304 Grade (natural finish) wire cloth complete all as direction of Engineer-in -Charge including supply and fixing of following items :- (a) Stainless steel (304 Grade) finished butt Hinges 100 mm, 4 Nos per leaf and table 6 of BIS 12817-2020 BIS Marked. (b) Stainless steel (304 Grade) finished square tower bold 200 mm long-2 Nos per leaf as per table 01 dia of bolt 12 mm as per BIS 12833. (c) Stainless steel (304 Grade) Finished Handles 200 mm-2 Nos per leaf. (d) Stainless steel (304 Grade) finished sliding bold 300 mm-1 No per leaf, 16 mm dia as per BIS clause (iii) of BIS 15834-2020. (e) Stainless steel (304 Grade) Finished Floor door stopper-1 140mm Nos per leaf. (f) Stainless steel (304 Grade) wire cloth fixing as per manufacturer's instructions

S&F for Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm thick size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 550 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. including supply and fixing following items :- (a) Stainless steel (304 Grade) Finished butt Hinges 100 mm, 4 Nos per leaf and table 6 of BIS 12817-2020 BIS Marked. (b) Stainless stell (304 Grade) finished square tower bold 150 mm long-2 Nos per leaf as per table 01 dia of bolt 12 mm as per BIS 12833. (c) Stainless steel (304 Grade) Finished Handles 100 mm-2 Nos per leaf

S&F 300mm ordinary rat tail rod pattern springs including roller and roller plate complete mild steel fixed complete all as specified and directed.

S & F 1st class hard wood (sal) or any other 2nd class hard wood articles not exc 200 Cubic Centimeter each Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labour etc complete all as specified

S&F for powder coated aluminium frame for doors, windows, ventilators and aluminium partition with one or more rebates including jointing cleats glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete with locking arrangements for fixing with powder coating on aluminium sections, minimum thickness of poweder coating shall be 50 micron as per the specification. The top and bottom horizontal members and vertical members adjacent to wall shall be fixed with floor, ceiling, walls and cills where required and fixed with the help of rawl plugs and screws or with fixing clips or with expansion hold plate fastners. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically whereever required complete in all respect all as specified & directed by Engr-in-Charge.

S & F Powder coated anodised aluminium door shutters, aluminium section weighting 0.55 kg/m including necessary joining cleats, glazing, clips, rubber neoprene packing, 2 Nos in each door, hinges (3 Nos), powder coated tower bolts and D type bow handles anodised alumium snap beading scrwes etc ) complete all as specified

S&F for powder coated anodised aluminium window and ventilator shutters, side hung type without sash, aluminium sections weighing exc 0.55 Kg/m (1.50 to1.80mm th) including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (01 No) hinges type B-21 100 mm long (2 Nos) suitalbe handle (01 No) in each window shutter and necessay accessary as required complete all as specified and directed by Engineer-in-charge Note: Glass will measured and paid separately.

S & F for Aluminium anodised (Powder coated) Three track sliding window frame with shutters (two glazed and one gauged shutter) including all necessary joining cleats, hold fast, rubber gasket, snap beading and locking arrangements fixed with screws to wall etc. complete and glazing with 5 mm thick tinted glass to aluminium frame work using rubber gasket and including stainless steel wire cloth of 0.36mm dia & average width of aperture 1.40mm with staple or suitable fillets wire mesh fitted with screws and washers etc with the following section of frame and shutter (A) Sections for frame (i) Top and verticals 92 x 29.50 x 1.30 mm thick (ii) Bottom 92 x 29.50 x 1.20 mm thick. (B) Sections for shutter (i) 'A' section 39 x 20 x 1.50 mm thick (ii) 'Interlock' section 39 x 20 x 1.50 mm thick(iii) 'H' section 41 x 20 x 1.10 mm thick Make: Jindal or equivalent sections of Hindalco.

S & F for Aluminium anodised grill (anodised transparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grae AC 15) of approved design/ pattern, with approved standard section and fixed to the existing window frame with CP brass/stain less steel screw @ 200 mm centre to centre including cutting the grill to proper opening size for fixing and operation of handles and fixing aprroved anodised aluminium standard section around the opening complete all as specified and directed.

S&F 4.8 mm thick sheet glass n. exc 0.50 Sqm in each pane, ordinary quality and glazing with aluminium snap beading of any size of glass in each pane with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufaturers all as specified and directed.

Supply & fixing, 4mm thick figured glass, pin head type and glazing with spring clips in metal surrounds and oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified & directed by Engineer-in- charge.

S& F stainless steel wire cloth 0.36 nominal dia of wire and average width of aparture 1.40mm and fixed with tinted tacks or stainless steel wire staples fixed to wooden/steel shutters complete all as specified and directed by Engr-in-charge.

S & F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

Supply and fixing in repairs door closer hydraulically regulated of aluminium cast type , designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed other parts made of mild steel heavy duty and fixed complete all as specified and directed.

Dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified & directed.

Material and labour for 7 to 8 mm thick non-skid ceramic colour (light shade) joint free tiles with matt finish premium quality having water absorption should be between 3% to 6%, square/ rectangular, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floor, set and jointed using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 including necessary cutting as per site requirement, complete all as specified and directed by Engineer-in-Charge.

All as per Ser item No 56 but as in skriting, but tiles laid over and including 10 mm thick bedding layer in cement mortar(1:3) complete all as specified and directed by Engneer -in-Charge

Material and labour for 7 to 8 mm thick non-skid ceramic colour (light shade) joint free tiles with matt finish premium quality having water absorption should be between 3% to 6%, square/ rectangular, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floor, set and jointed using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 including necessary cutting as per site requirement, complete all as specified and directed by Engineer-in-Charge.

Material and labour for Providing and Laying Premium (1st) quality having water absorption should be between 10% to 20%, digitally printed straight edge, punched, glazed ceramic rectangle tile in approved shade and finish with flexural strength greater than 16 N/mm2, scratch hardness on Moh’s Scale minimum 3 and crazing resistance of 2 cycles in coloured tiles 600 X 300 mm and 7 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified. Note : Dado should be flushed with the wall plastering.

M&L for machine cut pre polished kota stone slab flooring 20-25 mm thick over cement screed base laid over cement screed base laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed with grey cement slurry mixed with pigment to match shade of the slab including rubbing and plishing complete all as directed.

M&L for machine cut pre polished kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over and including 10 mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry mixed with pigment to match shade of the slab including rubbing and plishing complete all as directed.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and over 20 mm thick screed bed in CM 1 : 6 complete all as specified and directed by Engneer -in-Charge

M & L for Mirror polishing on marble/ granite/Kota stone/ Stone work where ever required to give high glass finish complete all as specified and directed by Engneer -in-Charge

Taking up or down GI tubing 15 mm bore pipe including cleaning for re-fixing or removal to store.

Taking up or down GI tubing 20 mm bore pipe including cleaning for re-fixing or removal to store.

Taking up or down GI tubing 25 mm bore pipe including cleaning for re-fixing or removal to store.

Supplying and laying of 20 mm (Outer dia) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 25 mm (Outer dia) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 32 mm (Outer dia) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Dismantling of cast iron pipes, jointed in cement mortar and taking out of trenches/wall if required 75/100mm dia complete all as specified and directed by engineer-in-Charge.

S&F in repairs 32 mm dia low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints, laid in trenches or in floors all as directed.

S&F 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as specified and directed by Engineer-in-Charge.

S&F 75 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as specified and directed by Engineer-in-Charge.

S&F 75 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints, laid in trenches or in floors all as directed.

S & F for PVC (SWR) bend 110 mm complete all as specified and directed by Engineer-in-Charge.

S & F for PVC (SWR) bend 75mm complete all as specified and directed by Engineer-in-Charge.

S&F grating doom CP 100 mm dia of SS with waste hole complete all as specified and directed

S&F in repairs grating doom CP 125 mm dia of PTMT with waste hole complete all as specified and directed

M&L in repair PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement all as specified and directed.

S&F in repair PVC (SWR) floor trap 75mm dia with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair towel rails 20mm dia D type 600mm long brass chromium plated complete all as specified and directed by Engineer-in-Charge.

S&F in repair chromium plated fancy type soap dish 15cm complete all as specified and directed by Engineer-in-Charge

Supply and fixing vitreous china premium/1st quality wall hung water closet with P trap white/ivory/off white including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc., and incl. plastic soft close seat cover as recommended by manufacturer for particular model closed pattern with flat bottom etc; and incl S&F of all necessary accessories set like rag bolts/gel gasket/hinges etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified. Make : Jaquar (Continental Series-CNS-WHT-963N or Techno commercial equivalent in make mentioned in Appendix 'B'

Supply and fixing concealed flushing cistern of PVC 8 ltr. cap with dual flushing system, valveless syphonic action type, with inlet/outlet, ball valve, float and including brackets and connection to pipe etc. and incl S&F of all necessary accessories/installation kit and 'S' type drain pipe connetion set for wall hung WC etc as recommended by manufacturer for fixing, packing and including S&F of actuator knob/flush plates and and taking down existing of any description/size complete in all respect all as specified. Make : Jaquar (Concealed Cistern-JCS-WHT-2400S, Flush Plate-JCP-CHR-812415) or Techno commercial equivalent in make mentioned in Appendix 'B'

S&F in repair vitreous china wash hand basin coloured flat back of size 550 x 400 mm vitrous China white flat back including brackets, waste coupling complete all as specified and directed.

S&F in repair Brass CP mixer 15mm bore for mixing hot & cold water screwed down for iron pipe for Kitchen sink complete all as specified and directed.

S&F in repair bib tap 15mm bore cast copper alloy chromium plated long body fancy type with capston head and cup screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge.

S&F in repair CP brass stop/angle valve fancy type 15 mm bore cast copper alloy screwed down high pressure fancy type with long shank and cup fixed complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 15 mm dia bore fancy type chromium plated concealed stop valves of cast copper alloy with long shank & cup etc. complete all as specified and as directed.

S&F in repair 125 mm dia chromium plated shower rose with or without swivel joints for fixing to15mm bore pipe etc complete incl taking down old one complete all as specified and directed by Engneer -in-Charge

Supply & fixing 450 mm long PVC connection 15mm size with PTMT nuts complete all as specified & directed by Engineer-in-charge.

S&F in repair chromium plated fancy type health faucet ABS body with 1.25 mtr tube & hook complete all as specified and directed by Engneer -in-Charge

S&F 32 mm Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified.

S&F in repair stainless steel chromium plated jet spray (butter fly or ''L'' bend) suitable for EWC including 1m tube and necessary nut bolts complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair glass corner shelf with CP brackets and CP railingcomplete all as specified and directed by Engineer-in-Charge.

S&F PVC bathroom cabinet mirror of size 450x350mm all as specified and directed by Engineer -in-charge

Supply and fixing in repair single lever High concealed diverter flow consisting of exposed part kit with operating lever, wall flange & button and concealed body, cartdge sleeve and also including bath spout with flange chromium plated ,screwed down, high pressure complete all as specified and as directed by Engineer-in-charge. Make Cera:(exposed part F1018721, concealed part F4030101, bath Spout F1020661) or Techno commercial equivalent in make mentioned in Appendix 'B'

Dismantling of water tanks of capacity exc 500 and n.exc 1000 ltrs and removing from site all as specified and directed.

S&F for Rotational moulded polythene water storage tank 1000 ltr capacity vertical with closed top, ISI marked hoisted and fixed in position connection nipple 2 Nos complete all as specified and directed..

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20mm bore complete all as specified and directed

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 25 mm bore complete all as specified and directed

Earth work in excavation by mechanical means (Hydraulic excavator) / in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil complete all as specified and directed by Engneer -in-Charge

Returning filling in incl spreading, levelling watering and well ramming in layer n.exc 25cm thick complete all as specified and directed.

Removing surplus soil to a distance n. exc 50 m and depositing where directed at level n. exc 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge

Demolition of Cement Concrete (reinforced) of any description and in any position not otherwise specifically provided for and rubhish off from premises complete all as specified and directed by Engr-in-charge.

M & L for nominal mix reinforcement cement concrete type B1 1:2:4 (20 mm graded aggregates) in chajjas over windows and doors complete all as specified and directed by Engr-in-charge.

M & L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finish surface of concrete flat complete all as specified and directed by Engr-in-charge.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon tal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed by Engr-in-charge.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified

Supply and laying DWCPE (SN8) 180 (OD)/150 (ID) mm dieameter drain pipes as per IS-16098 (Part-II), Laid in trenches on moorum bed to required slope, including all accessories/fittings, jointing and tested including demolition of breaking up of old drain pipes (Salt glazed ware, AC or reinforced concrete set in cement mortar) complete all as specified and as directed by Engineer-in-Charge

M&L Cement concrete 1:3:6 type C-1 using 20 mm graded as in coping including necessary formwork, weathering slightly rounded or chamfered angle and thorating complete all as specified and directed by Engineer-in - Charge.

M&L for PCC 1:2:4 type B2 using 40mm graded aggregates as in benching / haunching of manholes including forming channels including necessary formwork etc complete all as specified and directed by Engr-in-charge.

M&L precast cement concrete 1:2:4 type B1 using 20mm graded stone aggregate and set cement mortar 1:6 as in cover slabs (for manholes etc,) chajjas, shelves and similar articles with plain faces complete all as specified and directed by Engr-in-charge.

E/M Portion Taking down carefully copper/aluminium point wiring (light, socket or power) complete (fittings such as switches, ceiling roses, pendants, regulatos, sockets etc to be measured separately), and making good disturbed surfaces of walls, floors etc to match with existing surfaces.

Taking down MCB with sheet metal enclosure, main switch, DB, etc and making good disturbed surfaces to match with existing surfaces.

Taking down carefully submain wiring/ service connection of any type complete with casing caping / conduit etc complete all as specified and directed.

All as per srl item No 119 above, but for ceilling/exhaust fan paint controlled by one switch and regulator complete all as specified and as directed.

All as per srl item No 119 above, but for 3 pin 5 Amp socket outlet on the same board with other switch, sockets complete all as specified and as directed.

All as per srl item No 119 above, but for one 3 pin 5 Amp socket outlet on independent board complete all as specified & directed

All as per srl item No 119 above, but wiring with 4 Sqmm multistranded cable and earth wire with copper conductor of size 4 Sq mm for 15 amps power point all as specified

Supply and fix piano type, 230/250 Volts grade on top covers, Modular switch 1 way 6 A, 1 module complete all as specified and as directed.

Supply and fixed modular Socket outlet multipurpose type 2in 1, 3 Pin 6 Amp, flush type (2 module) complete all as specified and as directed by Engineer-in-charge.

Supply and fixed modular switch 6/16Amps, single pole, one way (1 module) complete all as specified and as directed by Engineer-in-charge.

Supply and fixed modular Socket outlet multipurpose type 2 in 1, 3 pin, 6/16 Amp, flush type (2 module) complete all as specified and as directed by Engineer-in-charge.

Supply and fixing LED tube light fitting polycarbonate housing 1 x 20 Watt, appx 4 feet long, with decorative box linear, housing environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to tube fitting, complete fitting with all accessories and following specifications, complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 110 Lumen per watt. (b) Input Voltage range : 140 to 270 volts. (c) Temp operating range : Minus 5°C to Plus 45°C (d) Power factor : Minimum 0.95 (e) THD : Current THD Max10% and voltage THD max 5% (f) IP rating : IP-20. (g) LED Driver of the same make as of the luminaire. (h) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (j) Surge protection minimum 2.5 kV. (k) CCT : Minimum 6000K (l) CRI : Minimum 80 (m) Rated life time : 50000 burning hrs @L70 (Average 10 to 12 hrs daily)

Supply and fixing single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amps, 240 volts, AC supply complete all as specified and directed by Engineer-in-Charge.

S & F in repair Lamp holder incl LED lamp 9 watt, insulated body with back plate etc all as specified and as directed.

Supply and fix in repair heavy duty exhaust fan, steel body AC single Phase. 230V of size 450 mm sweep with, blades and fan motor of Cap at least 190 Watt or above , and frame and louvers Complete all as specified and directed by Engr-In-Charge. Old U/S exhaust Fan will be deposited to MES Store yard by the contractor and no schedule of credit will be given tothe contractor on account of this item all as specified and directed by Engr-in-Charge..

Supply and fixing LED luminarie 600mm x 600 mm, 35/36 watt, 220 V AC recessed type with high effciency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceilling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed by Engineer-in-Charge.

Supply and hanging /fixing ceiling fan 1200 mm sweep AC Supply (Input Voltage Range ; 120 to 280V), BLDC type, 5 star rated, BEE and ISI Marked super enamelled, copper winding of 'B' class insulation, single phase, maximum 30W (± 10%), Temperature rise 40 degree maximum without remote with and including capacitive regulator, 03 No blades, down rod including accessories, white colour, total harmonic less than 10%, 5 speed, hanging in position including making connection with flexible cord three core twisted copper conductor of suitable size from ceiling rose to fan complete all as specified. Note :- (i) Serial Number as issued by Engr-In-Charge of celing fan and GE Office name shall also be written on fan with red colour permanent marker and fixing of regulator on switch board, cost for the same shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account

Supply and fixing energy efficient LED security light fitting of 35W pressure die cast aluminium housing/body, heat resistant clear toughened glass, better optics for uniform distribution street luminaire, with driver, including electric connection with using 2 core flexible copper conductor cable 1Sqmm from ceiling rose to light fitting, fixing the light fitting with new bracket made out of GI tubing light grade 32mm dia, 1.5 metre long bent to shape at 120 degree angle at half metre from bottom, including two Nos clamps made out of MS Flat iron size 25x3 mm with suitable nuts and bolts for fixing of bracket including painting to MS clamp and nut bolts with two coats of aluminium paint over a coat of red oxide primer, complete fitting with all accessories and following specifications, complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 110 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : Max10%. (f) IP rating : IP66. (g) IK rating : Minimum IK07 (h) Built in potted LED Driver of the make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection 10 kV (inbuilt + extended) (l) CCT : 5700 K. (m) CRI : Minimum 70 (n) Lens - High Efficiency wide angle lens. (o) BIS Approved fixtures and driver (p) Rated life time : 50000 burning hrs @L70 (Average 10 to 12 hrs daily)

Supply and fixing LED Bulkhead fitting 1 x 10 Watt, complete with Standard LED lighting fixture with extruded polycarbonate housing environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to light fitting, complete fitting with all accessories and following specifications complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 5°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : <15%. (f) IP rating : IP-65. (g) CCT : Minimum 5400K (h) Polycarbonate housing white coloured (j) LED Driver of the same make as of the luminaire. (k) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (l) Surge protection minimum 2.5 kV. (m) CRI : Minimum 80 (n) Rated life time : 50000 burning hrs @L70 (Average 10 to 12 hrs daily)

Supply and fix ceiling rose surface bakelite two to three terminals/plate 5 amps complete all as specified and directed by Engr-in-Charge.

M & L for 3 core 10 Sqmn PVC insulated unsheathed (FRLSH) cable with stranded copper conductor drawn in PVC conduit and accessories suitable size all as specified and directed by Engineer-in-Charge.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed layer of charcoal dust and common salt, connected to earth lead of GI wire 4 mm dia (8 SWG) by means of bolts, nuts and washers of the earth wire.galvanised iron or steel and thimbles and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 15mm dia and water pipe 20mm dia GI light grade with funnel and wire mesh, PCC chamber in cement concrete (1:2:4) type B-1 and CI cover with frame all as shown in electrical plate No. 3 of MES Schedule Part-I of SSR-2009. Notes :- (i) 20 mm dia GI pipe for watering to be provided with a socket and plug and should be 10 cms above ground level. (ii) Outer edge of earth pit will be 1 metre away from the outer edge of PCC chamber. (ii) GI wire upto DBs earth connection is included in this item. (iii) Water pipe shall be provided in slanting position

Supply and fix sheet metal enclosure DB single pole and neutral for 240 volts 8 way with 200 Amps rated busbar flush/surface mounting double door complete all as specified and directed

Supply and fix MCB single pole 240 Volt 6-32 Amps 10 KA complete all as specified and directed

Supply and fix MCB SPN 240 Volt 32 Amps 10 KA complete all as specified and directed

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

M/s Karan Builders (BID ID -3476143)

AJAY CONSTRUCTION COMPANY (BID ID -3482973)

PAREEK AND COMPANY (BID ID -3477514)

SHIVA CONSTRUCTION COMPANY (BID ID -3478156)

GHANSHYAM BHADU (BID ID -3477494)