PROVISION OF ADDITIONAL ROOMS IN THE EXISTING GUEST HOUSE AT DIHAR, LEH

Amount

CHAPTER - I EARTH WORK

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge

All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Supplying chemical emulsion in sealed containers including delivery as specified.

Chlorpyriphos/Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete:

With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor :

With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

Supplying and stacking at site

Good earth.

Banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m :

All kinds of soil

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

CHAPTER - II PLAIN AND REINFORCED CEMENT CONCRETE WORK.

Providing and laying in position cement concrete of specified grade excludingthe cost of centering and shuttering - All work up to plinth level

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size).

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing :

1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Centering and shuttering including strutting, propping etc. and removalof form for all heights :

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Shelves (Cast-in-situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Edges of slabs and breaks in floors and walls Under 20 cm wide

Weather shade, Chajjas, corbels etc., including edges

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/recoverable separately).

All works upto plinth level.

All works above plinth level upto floor V level.

Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used ispayable /recoverable separately. Providing M-35 grade concrete instead of M-25 grade BMC/ RMC. (Note : Cement content considered in M-35 is @ 350 kg/ cum)

Add / deduct for using extra / less cement in the items of design mix over and above the specified cement content therein.

Providing and laying cement concrete 1:6:12 (1 Cement : 6 coarse sand :12 graded brick aggregate 40 mm nominal size) in depressed portion of toilets, kitchen and balconies etc.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and placing in position 100mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick ,100mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage ,all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge

CHAPTER - III MASONRY WORK:

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with :

Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete :

1:3:6 (1 Cement: 3 coarse sand(zone-III) : 6 graded stone aggregate 20 mm nominal size).

Coursed rubble masonry with hard stone (first or second sort) in superstructure above plinth level and upto floor five level.

Masonry work (first sort), in cement mortar 1:6 (1 cement : 6 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

CHAPTER -IV WOOD / ALUMINIUM WORK

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Second class teak wood

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :

2nd class teak wood -50 x 12 mm

Providing 40x5 mm flat iron hold fast including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs

40 cm Long and embedding's in cement concrete block 30x10x15cm 1:3:6 mix (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

20 cm Long and embedding's in cement concrete block 20x10x15cm 1:3:6 mix (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing carbon steel galvanised(minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide P6 grade sleeve, including drilling of hole in frame, concrete/ masonry etc. as per direction of Engineer-in-charge 10 x120 mm

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality confo Metreing to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of stainless steel lever handles with necessary screws etc. complete (best make of approved quality).

Providing and fixing stainless steel Sliding door bolts of approved make, confirming to grade AISI-304 in 18/8 composition with nuts and screws etc. complete :

Providing and fixing stainless steel tower bolts of approved make, confirming to grade AISI-304 in 18/8 composition with nuts and screws etc. complete :

Providing and fixing stainless steel handles of approved make, confirming to grade AISI-304 in 18/8 composition with nuts and screws etc. complete :

125 mm long and 10 mm Dia

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing Stainless Steel floor door stoppers of approved make, confirming to grade AISI-304 in 18/8 composition with nuts and screws etc. complete.

Providing and fixing of rubber nylon door buffer (dia of 40mm and 50mm long) on wall with rowl plug and screw.

Providing and fixing stainless steel pull bolt lock of approved make, confirming to grade AISI-304 in 18/8 composition with nuts and screws etc. complete :

Providing and fixing 3 mm thick aluminium composite panel cladding of required size to Prelaminated Flush door shutter including fixing etc. complete as per direction of Engineer-in-charge.

Providing and fixing brass curtain rods of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete.

25 mm diameter

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) :

For fixed portion: Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge.

Prelaminated particle board with decorative lamination on both sides.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness

With float glass panes of 5.50 mm thickness

Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. complete.

Powder coated minimum thickness 50 micron aluminium.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

With Stainless Steel cover plate minimum 1.25 thickness

CHAPTER - V STEEL WORK

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.

Using M.S. angels 40x40x6 mm for diagonal braces

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to openings / wooden frames with rawl plugs (designation 10 No.) etc., all complete

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

CHAPTER - VI FLOORING

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade: Area of slab over 0.50sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Granite work

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Min size 300 x 450 mm)

Providing and laying Ceramic glazed floor tiles (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as white, Ivory, Grey, Fume, Red Brown, laid on 20mm thick cement mortar 1:4 ( 1cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

Size 300 x 300mm

Providing and laying double charged vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

Providing and laying double charged Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :

Udaipur green marble

Udaipur green marble stone in risers of steps, skirting, dado and pillars with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand ( Manufactured)) and jointed with grey cement slurry, including rubbing and polishing complete with :

Extra for pre finished nosing to treads of steps of marble stone.

Extra for marble stone flooring in treads of steps and risers using single length upto 2.00 metre.

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.

18 mm thick.

Providing and fixing glass strips in joints of terrazo/ cement concrete floors.

40 mm wide and 4 mm thick

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.

CHAPTER - VII ROOFING

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations :- (i) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (ii) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (iii) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineering-charge. (iv) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineering-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (v) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge :

With average thickness of 120mm and minimum thickness at khurra as 65 mm.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (i) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (ii) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (iii) (The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.)

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A including unplasticised - PVC moulded fittings/accessories to IS : 13592 Type jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes. Inclusive of all fittings.

160 mm diameter

110 mm diameter

Providing 50 mm dia G.I. Spout set in cement mortar 1 : 3 (1 cement : 3 coarse sand) complete.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 20 cm x 20cm and weighing not less than 995 grams.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I

CHAPTER - VIII FINISHING

12 mm cement plaster of mix :

1:6 (1 cement : 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix

1:6 (1 cement : 6 fine sand)

6mm cement plaster of mix:

1:3 (1 cement : 3 fine sand)

Neat cement punning

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.

20mm cement plaster (Over Sunken Treatment etc)

15 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall.

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers (01 Kg per bag of 50kg cement used in the mix)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) :

Flush/ Ruled pointing

Distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

Two or more coats on new work

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:

New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Applying priming coat :

With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing & fixing chicken wire mesh at the junctions of RCC and brick work, 100mm overlapping on both sides with all necessary hardware etc., complete.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per irection of Engineer - in - charge.

Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

In cement mortar

Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground, all complete as per direction of Engineer-in-Charge.

For door/ window/ clerestory window

Dismantling asbestos cement pressure pipes including excavation and refilling trenches after taking out the pipes manually/ by mechanical means and stacking the pipes within 50 metres lead as per direction of Engineer-in-charge :

Up to 150 mm diameter

Above 150 mm diameter

CHAPTER -IX : SANITARY INSTALLATIONS

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, including 10 litre low level white vitreous china cistern with dual flush fitting,including seal cover and cistern fittings, nuts,bolts and gasket etc. complete with all fittings including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

Two Piece Closet Hindware " ARIEL" model 20095 & vitreous china cistern Hindware model 21055 OR approved

Providing and fixing wall hung wash basin with CI brackets,Basin Mixture ,32mm CP brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever required. W.B Hindware model 10086 /approved equivalent.

White vitreous china wash basin flat back size 550 mm x 400 mm with basin Mixture Mixer of Make Jaquar -FLR 5001B or Equivalent (Bottle trap-Jaquar model no. ALD 769/approved equivalent, CP waste-Jaquar model no. ALD 709/approved equivalent,).

Providing and fixing 5mm thick beveled edge mirror of superior glass of approved quality and of required shape and size, fixed with teak wood beading / pvc of size 40x20mm with French spirit polish, 6mm thick water proof ply wood on back of the mirror etc. complete with two or more coats of black bituminous paint at the back of ply.

Providing & fixing in position C.P. brass twin coat hook including cutting necessary C.P. brass screws complete.(Jaquar model no. 1191N/approved equivalent).

Providing and fixing C.P.brass bib cock of approved quality conforming to IS : 8931.

15 mm nominal bore.(Jaguar model no. FLR- 5047N /approved equivalent).

Providing and fixing C.P.brass long body bib cock of approved quality conforming to IS standard and Weighing not less than 690 gms. (Jaguar model no. (Jaguar model no. CON-107KN /approved equivalent). /approved equivalent).

15 mm nominal bore.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing 100mm CP brass grating for trap.

Providing & fixing in position C.P. brass towel rail (600mm long) including cutting necessary C.P. brass screws complete.(Jaguar model no. ACN -1111NM /approved equivalent).

Providing and fixing C.P. Brass towel ring (200 mm Dia ) including cutting necessary C.P. brass screws complete.(Jaguar model no. AQN-7721 Towel Ring Round /approved equivalent).

Providing & fixing in position CP soap dish.(Jaguar model no. 1131/approved equivalent).

Providing & fixing C.P. brass shower assembly Jaguar model no OHS-1789 consisting of wall mixer (Jaguar model no. FLR- 5273 UPR), wall flanges and shower rose (Jaguar SHA - 477) & pipe upto shower rose complete.

Providing & fixing decorative six wall hook rack made from high quality/grade stainless steel of matt gloss surface finish including necessary C.P. brass screws complete.

Providing and fixing Stainless steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required.

Kitchen sink with drain board: 510 X 1640 mm Double bowl depth 250 mm

Providing and fixing P.V.C waste pipe for sink or wash basin including P.V.C waste fitting complete . (i) Flexible pipe

40 mm dia

Providing & fixing Sink Mixer with Swinging Casted Spout (Wall Mounted Jaguar model FLR -5163 /approved equivalent) with 450mm long copper pipes & brass nuts.

Providing and fixing white vitreous china urinal of appx. size 610x410x380mm Hindware Model no 60002 /approved equivalent) with push type urinal flushing arrangement(Jaguar model no. 077 /approved equivalent)including fixing to wall with suitable brackets all as per manufacturers specification & direction of Engineer-in charge with standard size C.P.brass flush pipe,spreader with unions & clamps(all in CP brass)including painting of fittings, cutting and making good the walls and floors where required.

Providing & fixing urinal partition of 12 mm th toughened glass ( size 675 x 330 mm) complete with brackets bolts nuts for grouting to wall complete in all respects.

CHAPTER - X : WATER SUPPLY

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chases and making good the wall etc.

PN - 16 Pipe, 20mm OD (SDR-7.4

PN - 16 Pipe, 25mm OD (SDR-7.4)

PN - 16 Pipe, 32mm OD (SDR-7.4)

PN - 16 Pipe, 40mm OD (SDR-7.4)

PN - 10 Pipe, 50mm OD (SDR-11)

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801 UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge.

PN - 10 Pipe, 50 mm OD (SDR-11)

Providing and fixing brass stop cock of approved quality complete.

20 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to I.S:8931 a) 15 mm nominal bore. (Jaquar model no. FLR-5053N /approved equivalent).

15 mm nominal bore

Providing and fixing unplasticised P.V.C connection pipe with PTMT Nuts coller and bush of approved quality and colour.

15mm nominal bore with 45cm length

Providing and placing on terrace (at all floor levels) Polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement amd making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing & fixing thermal insulation in hot water pipes a polyolefin foam of closed cells structure having thermal conductivity of 0.036 W/M.K at an average temperature of 30oC. All joints shall be sealed with adhesive & aluminim tape.

19 mm [6 mm thick insulation]

25mm [6 mm thick insulation]

32 mm [9 mm thick insulation]

42 mm [9 mm thick insulation]

51 mm [9 mm thick insulation]

Constructing masonry Chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement :4 coarse sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 Cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside palstering with cement mortar 1:3 (1 Cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :-

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing, fixing, installation, testing and commissioning of Solar Hot Water indirect Heating system using approved type of heating liquid medium comprising of flat plate solar panels, with single sheet absorber fin ,screw less construction of panel,including all interconnecting insulated GI piping, primary and secondary recirculation pumps, insulated hot water tank with PUF insulation including valves on inlet, outlet, Y strainer and a water meter on the inlet, air release valve all mounted on galvanized MS sections complete as required with connection with piping system. (connect the system to hot water mixing tank via 50 mm dia pipe) (make: Tata BP ,Honey well or equivalent ). (i) Supply, Installation, Testing & Commissioning of 1000 LPD flat plate solar collector panels of 2 x 1m size approx. the panels enclosed in insulated collected boxes with single piece toughened glass 3.5mm thick and fixed with heat resistant.panel Should have a single sheet absorber and screwless design. (Make: Tata BP,Honey well or equivalent). (ii) 1000 lts MS Pressurised tank(insulated). (iii) Inter-connected insulated GI piping insulated with 13mm thick nitrile rubber heat resistant insulation sections (Vidoflex or equivalent) and valves with outer mechanical protection of aluminium sheet cladding.

Supply installation testing and commissioning of 60 ltr capacity water cooler with SS body tank and water storage tank with R.O.water purifier comprising 5 micron filter and UV steriliser on cold water supply to work on single phase 230 volts 50 HZ AC power supply with capacity 120 lph.-Kent or equivalent ..

Providing in position storage type hot water electrical geyser( vertical or horizontal-1.5 kw) including making connection in all respects.-Venus/Racold or equivalent .

25 litres capacity.

CHAPTER - XI : DRAINAGE

Providing and fixing sound insulated Polyproplene piping (PP) system as per ON EN 1451-Part 1-6 & EN 12056 Part 1-5 EN 752, DIN 1986-100 - class B/D, with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type,WC pan connector, cleanout plugs, having high impact and stiffness, offering sound levels of not more than 22 dBA as per DIN 4109 at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, density of pipe to be 1.25gms/cm3, elongation = 0.05mm/m0K and tensile strength > 24 N/mm2,with all necessary fittings in blue colour, fitted with factory fitted lip ring. (POLOPLAST - PKNG or equivalent ).

110 mm dia POLO KAL NG

Providing and fixing PP white Trap with deep seal trap, rubber seal on inlet to push fit hopper for indirect waste connections (McAlpine, UK) with CP heavy duty grating. Making proper connection,cutting chase / hole in floors /slabs and bringing the same in proper condition and shape after placing the trap in right position complete as required

110 mm inlet and 110 mm outlet.

Providing and fixing sound insulated POLO KAL NG piping system with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, high impact and stiffness as per ON EN 1451-1 and DIN 19560 offering sound levels of not more than 21 dBA at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, with all necessary fittings in blue colour as per ON EN 1451-1 and DIN 19560 all fitted with factory fitted lip ring. ( For Indirect waste/ Wash Basin/Urinal/Sink/Floor Drain ).Cost shall include all associated civil works, core cutting,supports, structural steel supports as per manufacturer' standard design.

40 mm outer dia

50 mm outer dia

Providing, fixing, testing and commissioning of PoloPlast pipe inlet fittings with maximum 3 inlets 40, 50 & 75 mm OD size poloplast pipe, fixed to 'P' traps including Dripseal/Pipe seal/solvent weld joint/rubber ring joint complete .

110 mm outer diameter

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

150 mm dia. R.C.C. pipe

250 mm dia. R.C.C. pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :

100 mm diameter S.W. pipe / RCC Pipe

150 mm diameter S.W. pipes pipe / RCC Pipe

250 mm diameter S.W. pipes pipe / RCC Pipe

Providing and fixing square mouth SW gully trap class SP-1 complete with CI grating brick masonry chamber and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg. as per standard design. (i) 180x150mm size P type

with common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregrate 40mm nominal size ) inside plastering 12 mm thick with cement mortar 1:3 (1 Cement : 3 coarse sand) finished with floating coat of neat cement & making channels in cement concrete 1:2:4 mix (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80cm and 45cm deep including C.I. cover with frame (light duty) 455x610mm internal dimensions total weight of cover and frame to be not less than 38kg (weight of cover 23kg and weight of frame 15 kg). With common burnt clay FPS (non modular)bricks of class designation 7.5

Inside size 120x90cm and 90cm deep including C.I. cover with frame (medium duty) 500mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg). With common burnt clay FPS (non modular)bricks of class designation 7.5.

Extra for depth for manholes

Size 90x80 cm With common burnt clay FPS (non modular)bricks of class designation 7.5

Size 120x90cm With common burnt clay FPS (non modular)bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263mm and width as 165mm with minimum 112 mm space between protruded legs having 2mm thread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138mm as per standard drawing and suitable to with stand the bend test and chemical resistant test as per specification and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manhole with 30x20x15 cm cement concrete block 1:3:6 (1cement : 3coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth including consolidated each deposited layer by ramming, watering, etc. and disposing of surplus excavated soils directed, within a lead of 50m. All kinds of soil

Pipes, cables etc. exceeding 80mm dia. but not exceeding 300 mm dia.

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre)

BIODIGESTER TANK Providing and fixing testing and commissioning of Biodigester Tank for Cold climates and for 20 users, a 3.0 Cum liquid volume with puff PUFF insulated sandwiched by FRP reaction biodigester tank of M/S Arkin Creations or technocommercial equivalant with following specifications: Tank size: minimum 3.00 cubic meter liquid volume tank (1m depth-liquid) specially designed double walled FRP structure (outer wall 10mm, inner wall 6 mm thick) is required to be fabricated. There should be 03 partition wall (partial; 120cm x 100cm from opposite direction; thickness: 4-5mm). Inlet and outlet will also be made as per the design and requirement of the user. PUF Insulation: PUF (Poly Urethane Foam: liquid mixture) in between the two FRP walls (thickness of PUF 150mm) should be added during fabrication. Bacteria attachment sites (wall mounted and hanging type) should be there inside all the compartments in the tank Heating elements: Efficient heating elements (4 nos: 2x 100w & 2x 200w) should be customarily designed. The length of each heating element would be approx 90cm, which will be fitted on uniquely designed screw mounted system from the top of the tank. Sensor and Thermostat: two specially designed sensors (length 90cm) and two thermostats are required for maintaining water temperature inside the tank.

A 3000 litre (Three thousand litre) capacity designed tank for effluent water treatment cum soak pit is required for each tank. (Snow shed etc shall be Extra)

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

CHAPTER -XII : INTERNAL ELECTRIFICATION SUBHEAD I - LIGHT POINTS

Point wiring for Light / fan / Exhaust fan with 2 runs of 1100V grade 1.5 sq. mm & 1 run of 1.5 sq. mm FRLS insulated multistranded Copper wires, run in & including 25 mm dia , heavy duty PVC conduits concealed in wall after necessary chase cutting with finishing / surface on wall/ ceiling conforming to IS 732 including all accessories such as junction boxes, conduit bends, elbows and ceiling rose, anodised GI switch box with modular switch and the box covered with front plate.

One light point controlled by one 6A switch

Two lights points controlled by one 6A switch

Three lights points controlled by one 6A switch

Four lights points controlled by one 6A switch

Five lights points controlled by one 6A switch

Six lights points controlled by one 6A switch

Exhaust fan point controlled by one 6A switch & ceiling Rose

Supply and wiring similar to item 1 above but for ceiling fan point including GI Box and controlled by one 6A switch, 100W step type Electronic regulator with Concealed MS fan hook box.

Call bell point with 6A Bell push with Buzzer

Supply and wiring for 6A socket outlet with 2 runs of 2.5 sq. mm FRLS insulated multistranded Copper wire and 1 run of 1.5 sq. mm FRLS insulated multistranded Copper earth wire in and including heavy duty 25 mm dia PVC conduit concealed in wall after necessary chase cutting with finishing / ceiling / below work stations along with required accessories, supply and fixing of 6A 3 Pin socket with 6A modular switch in anodized GI box and front plate complete with fixing accessories etc. as required.( Independent)

Supply and wiring for 2x 6A socket outlet with 2 runs of 2.5 sq. mm FRLS insulated multistranded Copper wire and 1 run of 1.5 sq. mm FRLS insulated multistranded Copper earth wire in and including heavy duty 25 mm dia PVC conduit concealed in wall after necessary chase cutting with finishing / ceiling / below work stations along with required accessories, supply and fixing of 2x 6A 3 Pin socket with 2x 6A modular switch in anodized GI box and front plate complete with fixing accessories etc. as required.( Independent)

Supply and wiring for 2x 6A socket outlet with 2 runs of 2.5 sq. mm FRLS insulated multistranded Copper wire and 1 run of 1.5 sq. mm FRLS insulated multistranded Copper earth wire in and including heavy duty 25 mm dia PVC conduit concealed in wall after necessary chase cutting with finishing / ceiling / below work stations along with required accessories, supply and fixing of 2X 6A 3 Pin socket with16A modular switch in anodized GI box and front plate complete with fixing accessories etc. as required

Supply installation testing and commissioning of TPN MCB Double door Distribution boards dust and vermin protected and rated for 415V Three Phase AC supply operation including incoming MCB/ ELCB / RCBO as per specifications and required capacity Neutral bar and Earth Terminal complete as required and installed in concealed in wall after necessary chase cutting with finishing / surface on wall including all fixing materials required. MCBs shall conform to IS : 8828 and ELCB shall conform to IS : 12640. All MCBs shall be "C" Curve.

8Way TPN-MCB DB with 63A, 4 Pole RCBO-100mA as incomer and 24 Nos 10-25A SPMCBs as outgoing.(PDBs)

6Way TPN-MCB DB with 32A, 4 Pole RCBO-100mA as incomer and 18 Nos 6-16A SP MCBs as outgoing.(LDBs)

8Way SPN-MCB DB with 32A, DP RCBO-100mA as incomer and 6 Nos 6-A SP MCBs as outgoing.(LDBs)

LIGHT / FANS FIXTURES Supply , installation, testing and commissioning of the following luminaires comprising of basic channel, holder, Electronic Ballast / Low Loss Copper Ballast starter, condenser, control gear box complete with decorative attachments, lamps etc. as per specification and as per catalogue number giving below

1 x 18W Led ceiling hanging type light fixturte of wooden & metal material finish Philips Cat No. 31433

1x15 watt led -Ceiling Recessed light fixture Philips cat- DN 296B LED 15S 6500PSU WH

1x18W Led -Wall bracket matt gold light fixture Philips cat- 58070

1x7 watt LED -Ceiling light fixture surface type Philips cat- SM-250 C-LED 7S 6500 PSU

1x3.6watt led -Mirror light fixture -Philips cat- 34006 (QWZ802)

1x6W Led -Wall bracket bulk head light fixture Philips cat- WT -202-LED 6S NW PSU S-2 PC

1 x 20W Led wall bracket tube light Philips Cat No. BN 021C 20S-PSU - CW GR S-2

CEILING FANS

Supply and fixing of ceiling fan of 1200mm sweep ( white colour) suitable for operation on 230/240V, 50Hz, single phase, AC Supply complete with double ball bearing motor, required down rod, capacitor, three MS blades etc complete.

EXHAUST FANS Supply, Installation & testing of following 900 RPM Exhaust fan suitable for suitable for single phase 230/240V, AC Supply complete with motor MS louvers , mounting brackets, all accessories etc as complete.

230mm dia Plastic body ventilation fan

SUBHEAD II - : POWER WIRING

Supply and fixing of modular type single phase 16A 6 Pin shuttered type socket with 16A switch with front plate and anodized GI box including all fixing accessories.

Supply and fixing of single phase 1No 16A 6 Pin socket in GI box with 16Aswitch IN separate GI box, both of modular type with front plate compete as required ( Geyser Point)

Supply and fixing of modular type single phase 25A 3 Pin shuttered type socket with 25A switch with front plate and anodized GI box including all fixing accessories.( For heating system )

Supply and wiring with the following size 1100V grade FRLS insulated multistranded Copper conductor wires in and including suitable size heavy duty PVC conduit concealed in wall after necessary chase cutting with finishing / surface on wall / ceiling including all accessories such as junction boxes, bends elbows and end terminated with suitable lugs.

2 Runs of 4 sq.mm wires with 1 Run of 2.5 sq.mm in 25 mm dia PVC conduit ( For 16A Sockets & Geysers)

4 Runs of 4 sq.mm wires with 2 Run of 2.5 sq.mm in 25 mm dia PVC conduit ( For 16A Sockets & Geysers)

2 Runs of 6 sq.mm wires with 1 Run of 4sq.mm in 25 mm dia PVC conduit ( For 25A 1 Phase heating Sockets)

MV PANELS

Design, manufacture, supplying fixing in position, testing and commissioning of the following front operated modular compartmentalised construction cubicle type, front access, dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42 protection with hinged and lockable doors duly powder coated complete with incoming & outgoing MCCB's/MCB, aluminium busbars, interconnections, tinned copper crimping lugs, bonding to earth, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and panel shall have at least two spare cubicles to suit the highest rating outgoing MCB & suitable for a fault level of (25 KA) symmetrical at 415 volts. All switchboards shall have provision for entry of cables from the top/bottam as required. The cost shall include providing and fixing of 100 x 50 x 6 mm channels for switchboard support. All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The Busbars insulation shall be with heat shrinkable sleeves. SMC/DMC shrouds and busbar supports shall be used. Padlocking facility shall be provided on all outgoing feeders doors and switch handles shall be lockable OFF position All MCCB shall have rotary handles & extension terminal, phase barrier on both sides as required at site. All MDB / SDB panel shall be extendable type with cable alley. All fault level braking capacity shall be Ics value (ICS = 100% ICU). All MCCB shall have variable settings type.

SUBHEAD III - TELEPHONE / TV WIRING

Supply and laying of 25mm dia, heavy duty PVC conduit concealed in wall / ceiling / floor including all accessories such as Junction boxes, conduit bends, etc. completed as required for Telephones / TV /Data point etc.

Supply and laying of 32mm dia, heavy duty PVC conduit concealed in wall / ceiling / floor including all accessories such as Junction boxes, conduit bends, etc. completed as required for Unarmound Telephones cable etc.

Supply and fixing of Telephone outlet(RJ11) with anodised GI box with front plate.

Supply and fixing of TV outlet with anodised GI box with front plate.

Supply and fixing of computer outlet/data point outlet(RJ 45) with anodised GI box with front plate.

Supply and laying of 2 pair 0.6mm dia PVC insulated unarmoured copper conductor Telephone wire conforming to DOT Specifications

Supply and laying of RG 6 Cable in existing conduit

Supply and laying of cat - 6- gaga speed Cable in existing conduit

Supply and installation of following size TV Splitter in MS box complete as required.: Splitter- 4 Way

Supply and installation of following size Krone connectors in MS box complete as required.( hensel make ): 20 Pair

Supply and laying of 80 mm dia. Class "B" GI pipes laid 600mm below ground level including excavation, back filling etc., complete.

Supply and laying of 40 mm dia. Class "B" GI pipes in PCC foundation for TV & telephone etc., complete.

SUB HEAD IV - EARTHING EARTHING TAPES/WIRES

Supplying, fixing, jointing, and terminating of the following tapes/wires in masonry trenches/on walls/on cable tray/ along the cable with suitable G.I./Copper Clamps, screws etc. The wire shall be terminated with proper sockets, washers, bolts & nuts. All joints shall be rigid using double rivets : 25 x 5 mm GI Tape

EARTH STATIONS:

Supply, Installation of long life Maintenance Free Earthing System. The Rod shall be of Copper Bonded Steel with 17.2 mm dia. and 10 feet length with a core of mild steel molecularly bonded with min. 250 microns coating of 99.99% pure electrolytic grade Copper and exothermically welded Cu Busbar of 50X6X200mm both tested by CPRI capable of bearing fault current of 25 kA. Along with earth enhancement compound tested by RoHs complying IEC 62561-7 in a sealed bag of minimum 30 kg (10 kg Bag x 3) resistivity is less than 0.2 ohm meter . The earthing shall be with Suitable Poly-plastic Pit Cover with lockable arrangemen ( JMV/ERICO)

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

CHAPTER -XIII : EXTERNAL ELECTRIFICATION WORK CABLE , END TERMINATIONS & CABLE TRAY

Laying of the following size 1.1KV grade XLPE insulated armoured aluminium conductor under ground cable, in built up cable trench / already laid RCC Hume pipe or on cable tray / through GI pipe with all installation materails. When the cable is to be laid in ground, the same shall be laid at a depth of 750 mm below ground level including excavation and refilling of earth after cables are laid, providing sand cushioning and protection with bricks at sides and top and cable route markers at every 50 mtr. interval and also at the turnings. The cable shall conform to IS 7098/ Part I.

3.5 core 70 sq. mm. Alu XLPE (Above 35 sq.mm and upto 95 sq.mm )

Laying in ground

Laying in Trench / cable tray / GI Pipe

Supply testing and commisioning of the following size 1.1KV grade XLPE insulated armoured aluminium conductor under ground cable, in built up cable trench / already laid RCC Hume pipe or on cable tray / through GI pipe with all installation materails.

3.5 core 70 sq. mm. Alu XLPE

Provding end terminations for the cable specified below with Double compression type gland, Bi-Metalic lugs using crimping tool, Insulation tape, Identification tags etc. including end termination.

3.5 core 70 sq. mm. Alu XLPE

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.

100mm dia

CHAPTER -XIV: : Back up-power of -DG-Set

Supply installation, Testing and Commissioning of silent type DG sets of

Supply, installation, testing and commissioning of 62.5KVA at (NTP Condition (35 KVA Site Output) SILENT Diesel Generator set radiator cooled type suitable for of 415V, 3 phase 4 wire, 0.8 pf. (lagging) 50c/s A.C supply complete with engine (1500 RPM) and alternator DG Set controller with accessories including cold stating kit & residential type silencer and fuel service tank (internal) 110 liters capacity, battery and battery charger with all associated accessories, including standard set of tools and anti-vibration mounting pads, MCCB. Regulator through inbuilt AVR, digital governing

Supply and fixing of 990 Litre fuel tank made of MS plate 2 mm thickness with provision of manhole, in/out sockets, drain out plugs including supply/return pipe etc. as required at site.

Supplying and fixing of under noted 'B' class M.S. pipe for D.G. exhaust complete with bends, elbow, flanges etc. as required.

75 mm dia pipe

Supply and fixing of 50mm thick compressed mineral wool insulation for D.G. exhaust pipe with 26 gauge aluminium sheet cladding etc. as required for the under mentioned dia pipe.

75 mm dia pipe

Residential silencer for 62.5 KVA D.G set insulation

Supply, fabrication and installation of M.S. Structural Steel supports for exhaust pipe, fuel pipe etc. including supply and applying of enamel paint of approved shade after one coat of steel primer of reputed company.

Earthing For DG Body

Supply, Installation GI Electrode Earthing with 40 mm dia and 3 meter length, The electrode should be hot-dip galvanized with 120-150 micron. The GI Strip In Pipe Electrode shall be pre-filled with Crystalline Conductive Material (CCM) . The GI electrode shall be surrounded with 50 kg JAM Fill compound to provide maximum contact between the electrode and JAM Fill Compound. Backfill compound should be eco-friendly and having RoHs certification. GI Electrode Earthing should be maintenance free and dose not required regular manual addition of water. GI Electrode Shall be tested from CPRI. The earthing pit should be cover with CI cover, of 300 x 300 mm. GI Electrode earthing should be as per JAM 193. Make - JMV , Bradley, Coron.

Earthing for DG Neutral

Supply, Installation CU Electrode Earthing with 40 mm dia 2 mm thick and 3 meter length pure electrolite copper including from top to bottom 25X4 mm copper strip with both sealed . Each CU Electrode shall be pre-filled with Crystalline Conductive Material (CCM). The CU electrode shall be surrounded with 50 kg Jam Fill compound to provide maximum contact between the electrode and Jam Fill Compound. Jam fill compound should be eco-friendly and having RoHs certification. CU Electrode Earthing should be maintenance free and dose not required regular manual addition of water. CU Electrode Shall be tested from CPRI. Electrode earthing should be as per JAM 193. The earthing pit should be cover with CI cover, of 300 x 300 mm. Make - JMV, Bradley, Coron.

Supply Installation of of GI Strip of Size 25X5 to connect earth pit with DG S sets . All Accessory should be supply along with Strip. Supply of SS nut, bolt and washer should supply with strip as per drawing & required

Supply Installation of of copper Strip of Size 25X5 to connect earth pit with DG S sets . All Accessory should be supply along with Strip. Supply of SS nut, bolt and washer should supply with strip as per drawing & as required

CHAPTER -XV : CENTRE HEATING SYSTEM

Supply, installation & commissioning of Hot Water Heater capable of delivering a heat output of 100000 K.cal/hr, using HSD providing hot water at 90 Deg C having good thermal efficiency of thermax or equivalent make including base frame, control panel, electric panel, mounting frame, suitable for operation on 50 Hz, 3 phase, 415V AC supply and all complete as specified.

Supply and installation of MS chimney made out of 3mm thick MS sheet, minimum 1.2m above the highest point of the building roof and its diameter shall be as per the manufacturer's recommendation. The item shall be complete with the mounting/fixing arrangement as required.

Supply, installaing, testing and commissioning of mono-blocK centrifugal pump with bronze impeller, driven by suitable capacity electric motor of IE-3 for hot glycol complete with accessories and insulated with 50mm 24 kg/m³ density glasswool & covered with 24 gauge aluminium cladding as specified including foundation as per manufacturer instruction and suitable for a flow rate of 75.8 USGPM and 24m head. (1 working + 1 standby)

Supply and install balancing tank 990 ltr capacity made out of 3mm thick MS sheet. duly insulated with 50mm thick thermocol of density 16/ Cubic mtr and insulated with 26 gauge aluminium sheet

Supply and install diesel storage tank 500 ltr capacity made out of 4mm thick MS sheet. duly insulated with 25mm thick thermocol of density 16/ Cubic mtr and insulated with 26 gauge aluminium sheet

Supply, erection. Testing and commissioning of HDPE Expansion tank of capacity 500 Ltrs. with all fixing accessories and insulated with 50mmk thick TF quality EPS material and covered with 26 Guage Aluminium sheet complete as per specifications.

Supply, installation, testing and commissioning of Hi Wall split heating units with compact cooling coil, multispeed fan motor, the blower shall be dynamicaly balanced and designed for silent operation, the filters shall be washable synthetic media type arranged for convenient cleaning and as required with following capacity, including pvc drain which connect to nearest drain, and all necessary fitting which required to connect unit with hot water pipe in all respect.

3500 Kcal/Hr./1.0 TR (400 CFM with 15mmSp)

5250 Kcal/Hr./1.5 TR (600 CFM with 15mmSp)

7000 kcal/Hr./2.0 TR (800 CFM WITH 25mmSP)

PROPELLER FAN

Supply, installation, testing and commissioning of axial type Propeller fan with gravity louvers of the following capacity of approved make and specification. :50 cfm dia 200mm

STEAM TYPE HUMIDIFIER

Supply, installation, testing and commissioning of steam Type Humidifier package (to be fitted near hiwall split unit) of following capacities. (The humidifier shall be interlocked with thermostat of RH sensor). The unit shall be complete with all necessary electric equipment, like incoming MCCB, contractors, etc. as required. Note:- Water Supply & Drain connection to be provided by plumbing team for humidifier. 1.0 kg./hr.

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with TF quality expanded polysterene molded pipe sections of density not less than 20 Kg/cu.m, after a thick coat of cold setting adhesive (CPRX compound) covered with two layer of 120gm/sqm polythene sheet(vapour barrier) and finally applying 0.63mm Al Sheet cladded with type3, grade I roofing felt strip at the joints as per specifications .

65mm dia (50mm insulation)

50mm dia (50mm insulation)

40mm dia (50mm insulation)

32mm dia (50mm insulation)

25mm dia (50mm insulation)

20mm dia (50mm insulation)

Supply fixing, testing and commissioning of insulated valves and specials for hot water lines of following sizes

65mm butterfly valve

50mm butterfly valve

40mm butterfly valve

65mm dia. Balancing Valve

40mm dia. Balancing Valve

25mm dia. Balancing Valve

65mm dia. Non Return Valve

65mm dia. Y-Strainer

Ball Valve 20mm dia. Without Strainer

Ball Valve 20mm dia. With Strainer

Dual type Thermometers ( -10°C to 50 °C)

Pressure Gauge (Range 0 to 10 kg/cm²)

Supply, Installation, Testing, & Commissioning of 10mmdia. Automatic air vent in brass construction complete with nipples, union etc. as required at all high points in the pipe lines. The valve shall be such as to have non-return valve as integral part of the vent. make Anergy.

Providing and fixing in position flexible connections, complete with split steel retaining rings, single unfilled arch,, integral rubber flanges, fixing bolts, nuts, washers etc. as specified. The flexible pipe section shall have reinforcement of high tensile cord and non-migrating metal and should have NEOPRENE cover to protect the body from atmospheric conditions and/or mechanical damages of following sizes as required.

65mm dia

MAIN HVAC PANEL

Cable

Supply of the following 1100 volts grade, Aluminium/Copper conductor, XLPE insulated, PVC sheathed, steel armoured/Unarmoured cables as per IS 7098 Part-1 and as per technical specifications of this tender and directions of Engineer-in-Charge.

4 CORES AL. CONDUCTOR

4C X 16 Sqmm

3 CORES Cu. CONDUCTOR

3C X 4 sqmm

3C X 6 sqmm

SUB HEAD-VI (MV CABLE END TERMINATIONS)

Supplying and making indoor end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2/3/3.5/4 CORES AL. CABLE WITH AL. LUGS 4C X 16 sq. mm (28mm)

Supplying and making indoor end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2/3/3.5/4 CORES Cu. CABLE WITH Cu. LUGS 4 X 6 sqmm

Providing switch socket outlet 5/15 Amp with plug top and wiring with 2.5 Sqmm copper wire with 1 earth wire laid in PVC casing caping fixed on the wall for running fan coil unit.

Providing and fixing connecting, testing and commissioning of room thermostat of Honeywell Make for controlling split unit blower, Rh etc.

EARTHING

Supply, installation, testing, commissioning of Earthing. 8 SWG Gi Wire

25x3mm earth strip

Supply, testing, commissioning of earth pits with 65mm dia 3 mtr long GI pipe complete with Salt and Charcol, Masonary Chamber water pipe etc. complete

Supply, fabrications and fixing of structural steel for support etc.

CHAPTER -XVI : FURNITURE

SOFA Supplying and placing of Leatherite sofa of size Make: Pisa of Godrej or equivalent model of Steel Case , Vitra, Herman Miller , featherlite . SEAT FOAM‎: ‎The seat is made of PU ‎foam with Density ‎28‎± ‎2 ‎kg‎/‎cu‎.‎mtr having an ‎additional top layer of super soft ‎PU foam in Density ‎32 ‎± ‎2 ‎kg‎/‎cu‎. ‎upholstered with fabric ‎or leatherette‎. BACK ‎FOAM‎: ‎The back is ‎made of PU foam with ‎Density ‎28 ‎± ‎2 ‎kg‎/‎cu‎. mtr with two additional ‎top layer of supersoft ‎ foam of density ‎32‎±‎2 ‎kg‎/‎cu‎. ‎mtr‎, ‎upholstered ‎ with fabric or leatherette UNDERSTRUCTRE ‎: ‎Understructure is made ‎up of ‎1‎.‎2‎±‎0‎.‎1 ‎cm‎. ‎thick ‎hot pressed plywood ‎( moisture resistance & termite proof as per IS: 303) & pinewood of cross section devoid of major knots & surface defects 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose.

‎Single Seater: LEG ASSEMBLY‎: ‎It is ‎a welded assembly ‎made in Stainless steel ‎(‎grade SS ‎202‎) ‎tube ‎& ‎plate‎ with plastic endcap. (W) 86.0* (D) 90.5(H) 85.5 cm seat (H) 45.0 cm. Model - Pisa 1S

‎Three Seater SOFA (3S): ‎LEG ASSEMBLY‎: ‎It is ‎a welded assembly ‎made in Stainless steel ‎(‎grade SS ‎202‎) ‎tube ‎& ‎plate‎ with plastic endcap. (W) 206.0* (D) 90.5(H) 85.5 cm seat (H) 45.0 cm.

Supply of Peg Table of following sizes made out of second class teak wood frame, side with 70 X 25 mm teak wood and 45 X 45 mm teak wood decorative legsas per approved design, including 20 X 20 mm teak wood moulding all exposed surfaces to be finished with melamine polish with two or more coats all complete. Of size 450 X 450 X 400 mm with 8mm thick bevelled edge glass top.

Centre Table of following sizes made out of second class teak wood frame, side with 70 X 25 mm teak wood and 45 X 45 mm teak wood decorative legs as per approved design, including 20 X 20 mm teak wood moulding all exposed surfaces to be finished with melamine polish with two or more coats Of Size 900 X 900 X 400 mm with 8mm thick bevelled edge glass top.

Supply of Hard Bed (Single) of size 1950x900mm head board 800mm & foot board 400mm height made out of 32mm thick commercial block board having 4mm thick veneer & 32x6mm beading on edges, sides rails with teak wood of size 120x30mm including 12mm thick commercial ply on top , 4Nos supports of second class hardwood of size 45x30mm and necessary hardware finished with spirit polish etc. all complete.

Supply of Bed hard Double of size 1950x1850 mm made out of 19 mm thick commercial board with 4 mm thick teak ply side with 300 mm wide back with 60x60 mm teak wood leg with 19 mm thick commercial board with 4 mm thick teak ply head rest 900x1850 mm made out of teak wood frame with decorative ply 4 Nos IInd class hard wood support of size 60x40 mm thick top with 12 mm thick commercial ply finish with melamine polish and with two nos mattress of suitable size and 100 mm thick etc. complete as per drawing.

Supply of Bed Side Table of size 450 X 400 X 400 mm made out of 19 mm thick commercial block board & 6 mm thick ply on the back. Having one drawer and open shelf all exposed edges to have teak wood lipping including hardware and finished with spirit polish etc all complete.

With 3.5 mm thick teak veneer of approved shade & quality.

Supply of writing table of size 1050 x 600 x 750 mm made out of teak wood legs 45x45mm,sides with 19mm thick commercial board with 4mm thick teak veneer & front with teak wood of size 120x30mm, top with 19mm thick commercial board with 1mm thick laminate, top to have addition moulding of 70x15mm provided with 1Nos of drawers ride on telescopic channels. all exposed edges to have lipping finished with spirit polish etc. all complete.

Supply of Writing chair (with arm) of size 550 x 450 x 900 mm made out of teak wood frame front leg of cut to oriental shape & back leg with 40 x 30 mm tapered and back with 3 wooden strips and back top with decorative cutting as per sketch seat with cushion of 50 mm thick making with rubber with spring covered with fabric in approved shade and melamine polish etc. all complete as per drawing

Supply of Dining table for 6 persons of size 1800x900x750mm made out of teak wood frame ( side rail 90x30mm & legs 70x70mm) top edge with 38mm thick ( 19mm+19mm) commercial board and 1mm thick laminate all exposed edges to have lipping finished with spirit polish etc. all complete

Supply of Dining table for 2 persons of size 900x900x750mm made out of teak wood frame ( side rail 90x30mm & legs 70x70mm) top edge with 38mm thick ( 19mm+19mm) commercial board and 1mm thick laminate all exposed edges to have lipping finished with spirit polish etc. all complete

Supply of Dining Chair of size 450 x 450 x 900 mm made out of teak wood 45X30mm frame work without arm with 12 mm thick commercial ply with 50 mm thick high density foam on seat duly upholstered with fabric of approved shade and quality back having teak wood strip in Curve shape including spirit polish etc. all complete.

Providing and placing in position, Mid back chair of Make: Godrej or equivalent model of Steel Case , Vitra, Herman Miller . The seat & back are made up of 12mm thick hot pressed plywood, upholstered with fabric & moulded with Polyurethane foam together with moulded ABS seat and back covers. The back foam should designed with contoured lumbar support for extra comfort. Mid back size 475 mm Width x580 mm height and seat size 470 mm Width x480 mm. The polyurethane foam should be moulded with density 45 kg/m3 and hardness 16 +/2 kg on hampdem machine at 25% compression. Armrest are injection moulded from black copolymer polypropylene. The mechanism should be fixed 360 degree revolving type, Upright position locking, tilt tension adjustment, seat back tilting ratio 1:3. The pneumatic height adjustment has an adjustment stroke of 12 cm. The pedestal should be injection moulded in black 33% glass filled in nylon 66 with 5 nos twin wheel castors. The pedestal should be 66.3 cm pitch-center dia.

Providing & Placing of Full Height Metal storages of size 900(W)x450(D)x2100mmH) duly powder coated. Door Opening Twin door with self closing hinges. The add on units can be stacked width wise to form a row of storages having a common side pannel. legs are fitted with screw type leveller adding 45 mm to the height. Body made from 0.5 & 0.8 mm CRCA combination. CRCA- D grade as per IS513. Heightwise adjustable sheves having load carrying capacity of 40 KG, Max 4 nos. of adjustable shelves.Epoxy Polyster powder coated to the thickness of 50 microns.Doors consdtruction made up of MDF & honeycomb with backing and decorative laminates. Self Closing Hinges and Mazak Handle. 2 mm thick lipping on all edges and 3 way locking mechanism.Make: Gain of Godrej or equivalent model of Steel Case , Vitra, Herman Miller .

Designing, Supplying and installing of Factory made Laminated High density fibre board (Exterior grade laminated HDFB of Exterior grade) modular kitchen cabinet under the kitchen counter (max. 600mm deep), kitchen is to be provided with minimum nine nos. of stainless steel wire basket on sliding Telescopic rail, one no. grain trolley and shelves etc. along with other necessary fittings, accessories and hardware as instructed by the Engineer in Charge. Before fabrication of the cabinets, contractor will prepare, design/detail layout drawing of Kitchen as instructed by Engineer in Charge for approval Entire Kitchen Cabinetry like body panels, frame, shelves, partition, door shutters, front panel etc. are to fabricated out of 18 mm thick laminated HDF Board of Exterior grade. All ends of HDF Board to be finished in matching PVC edge bending tape and 5.5 mm thick mm one side laminated HDF Board of Exterior grade on back complete. . Necessary supports /stiffeners etc. to be provided in Cabinetry box, shelves, partition and door etc. for stability. Entire kitchen cabinetry inside outside including door shutters/front panels etc. to be laminated inisde as well as outside(outside decorative laminate and inside base laminate). All sliding channels in wire basket/drawers shall be of high precision double extension ball slides. Hinges must be of high quality, corrosion resistant, spring loaded with 105 degree opening and shall be fixed from inside. Wire baskets must be of top quality 304 grade stainless steel wires and must be further surface treated with nickel chromium plating. Galvanised steel shelves must be used in case of Hinged door unit, the load carrying capacity of the shelves not less than 60 kgs. Handles must be of die cast handle made of zinc alloy / or SS 304 to ensure high corrosion resistance and aesthetic. Skirting must be made of Poly Vinyl Chloride(PVC) for lighter weight and being unaffected by water. Only Front visible area in elevation is to be measured for billing purpose.

Designing, supplying and installing of Factory made Laminated High density fibre board (Exterior grade laminated HDFB of Exterior grade) , 300 mm deep and 600 mm high overhead modular kitchen cabinet with glazed / solid shutter. For glass doors 4 mm thick toughened glass in wooden frame to be used, width of the shutters preferably not more than 400 mm. Factory made Laminated High density fibre board (Exterior grade laminated HDFB of Exterior grade) shelves, not more than two nos. in each compartment. Before fabrication of the cabinets, contractor will prepare, design/detail layout drawing of Kitchen as instructed by Engineer in Charge for approval Entire Kitchen Cabinetry like body panels, frame, shelves, partition, door shutters, front panel etc. are to fabricated out of 18 mm thick laminated HDF Board of Exterior grade. All ends of HDF Board to be finished in matching PVC edge bending tape.nd 5.5 mm thick mm one side laminated HDF Board of Exterior grade on back complete. Necessary supports /stiffeners etc. to be provided in Cabinetry box, shelves, partition and door etc. for stability. Entire kitchen cabinetry inside outside including door shutters/front panels etc. to be laminated inisde as well as outside(outside decorative laminate and inside base laminate). Handles must be of die cast handle made of zinc alloy / or SS 304 to ensure high corrosion resistance and aesthetic. Only Front visible area in elevation is to be measured for billing purpose.

Supplying and fixing wood cupboards fabricated out of 18 mm thick laminated HDF Board of Exterior grade/ block board of teak finish laminate, for sides, tops, bottom / base, shelves and partition and 5.5 mm thick mm one side laminated HDF Board of Exterior grade on back complete. The cupboard shutters will be 18 mm thick laminated HDF Board of Exterior grade including IInd class 4 mm thick teak wood lipping / pvc lipping on edges including necessary screws and bright finished stainless steel piano spring loaded hinges, stainless steel ss handles, magnetic door catchers, 75 mm locks with four levers etc complete hardware as per direction of Engineer-in-charge. Entire cupboard inside outside including door shutters/ front panels etc. to be laminated inside as well as outside(outside decorative laminate and inside base laminate). Each cupboard in the Guest room is to be provided with minimum four nos. of drawers fixed with stainless steel soft closing heavy type telescoping channel . shelves height should be from 300 mm to 400 mm and partition should be from 750 mm to 1000 mm all complete as per direction of Engineer-in-charge.

600 mm deep

300 mm deep

Supply & fixing of Suitable Kitchen chimney of standard make like Kutchina, Faber/Ventair (Similar to Kutchina Model Stanza SS, Size 760mm x 530mm x 145mm, suction 1100 to 1300 CuM with exhaust hood as per specifications or equivalent with motor having minimum one year warranty and First year 3 free services & spares warranty except for bulbs. Item should be approved by Engineeer-in-charge

VASTU SHOBHA

LIRA CONSTRUCTIONS PVT LTD

ARP ASSOCIATES PRIVATE LIMITED