Construction of Jal Shakti Vibhag Rest House at Haroli in District Una, H.P. (SH Construction of civil work, Pdg and installation of sanitary fitting and electrical installation)

Amount

Excavation in foundation , trecnches etc., in all kinds of soil such as pickwork, jumper work blasting work,kankar moorum,singles including decomposed soft and hard rock,including chiselling wedging clearance of bushes etc.including shoring, dewatering etc. in all leads and lifts stacking the excavated soil not more than 3 meters clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinth and sides of foundation etc. consolidating each deposited layers by ramming and watering and then disposing of all surplus earth within all leads and lifts complete to the entire satisfaction as directed by the Engineer-in-charge

Providing and laying cement concrete 1:4:8(1cement:4sand:8 graded crushed stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of materials in all leads and lifts complete as per the direction of Engineer-in-charge.

Providing and laying cement concrete work 1:1½:3(M:25 grade)(1cement:1½sand: 3 crushed stone aggregate 20mm nominal size & curing complete excluding the cost of form work and reinforcement for reinforced concrete work in following items including carriage of material in all leads & lifts complete as per the direction of Engineer-in-charge.

Foundation footing, bases of columns and like mass concrete etc.

Column, pillars, posts and struts upto floor two level

suspended floors,roofs,landing and shelve and their supports balconies beams,girders bressumers and centilevers upto floor two level

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto floor two level

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in following item including carriage of material in all leads & lifts complete as per the direction of Engineer-in-charge.

Foundation, footings basis of columns etc. and mass concrete.

flat surface such as soffits of suspended floors, roofs, landings and like floors etc. upto 200mm in thickness

Columns, pillars, posts and struts Square, rectangular or polygonal in plan.

Stair cases with sloping or stepped soffits excluding landing.

Sides and soffits of beam,beam haunching,cantilever and bressumers and lintels not exceeding 1 mtr. In depth in all heights from floor complete in all respect with in all leads and lifts.

Edges of slabs and breaks in floors and walls: under 20 cm. wide.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like.

Providing tor steel reinforcement for RCC work including bending binding and placing in position complete upto floor two level including carriage of material in all leads & lifts complete as per the direction of Engineer-in-charge.

Ist class brick work using common burnt clay building bricks in supper structure above plinth upto floor two level in cement mortar 1:6(1cement:6sand) including carriage of materials in all leads & lifts complete as per the direction of Engineer-in-charge.

1st class Half brick masonry in common burnt clay building bricks in :Cement Mortar 1:4 (1 Cement : 4 Sand) including carriage of materials in all leads & lifts complete as per the direction of Engineer-in-charge.

Providing wood work of saal wood (Red saal ,minimum weight 700 to 800 kg/cum) in frames of doors,windows,clerestory,windows and other frames wrought, framed and fixed in position complete including carriage of materials in all leads & lifts complete as per the direction of Engineer-in-charge.

Providing and fixing panelled glazed or panelled and glazed shutters for doors,windows and clerestory windows i/c bright finished/black enamelled iron butt hings with necessary screws 1st class teak wood 40mm thick including carriage of material in all leads & lifts

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws 1st class teak wood 40mm thick including carriage of material in all leads & lifts.

Ist class brick work using Machine Moulded brick with fine surface and even edges in common burnt clay building bricks,laid with 12x12mm deep cut pointing, in supper structure above plinth upto floor two level in cement mortar 1:6 (1cement:6sand) including carriage of materials in all leads & lifts complete as per the direction of Engineer-in-charge.

15mm cement plaster in single coat on rough side of brick/stone masonry for interior plastering upto floor two level i/c arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 20mm in girth and finished even and smooth cement mortar 1:6 including carriage of material in all leads & lifts.

20mm Cement plaster in single coat on rough side of interior plastering upto floor two level ncluding arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:4 including carriage of material in all leads & lifts.

Cement concrete flooring 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size ) laid in one layer finished with floting coat of neat cement in all leads and lifts and as per the direction of the Engineer-in-Charge 40 mm thick including carriage of material in all leads & lifts.

Cement plaster skirting (upto 30cm height) with cement morter 1:3 (1 cement:3 sand) finished with a floating coat of neat cement including rounding of junction with floor 20 mm thick including carriage of material in all leads & lifts.

Kota stone slab flooring 20 mm (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. including rubbing and polishing complete including carriage of material in all leads & lifts. 30 mm thick.

Providing and laying granite stone in flooring 20mm (average) thickness base of cement mortar 3 (1cement: 3sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete 20mm thick including carriage of material in all leads & lifts.

Providing and fixing 10mm thick polished/satin/matt/ antiskid water proof stain and impect resistent heavy duty vetrified tiles degital/ full body of Simpolo/KaJARIA/ Nitco or equivalant 60X60 OR600x120mm OR 80X120 x10mm manufactured of approved shade and colour inflooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required (fixed with 5mm spacer,filled with epoxy) complete including carriage of material in all leads & lifts.

Providing and laying spartic ceremic tiles ORIENT BELL / KAJARIA MAKE 10mm.thick in flooring (600 x 600mm/required. size)treads of steps laid on a bed of 12mm. thick cement mortar 1:3(1cement:3 sand) finished with flush pointing in white cement including carriage of material in all leads & lifts.

White glazed tiles 8 to 10 mm thick 30x60 or 30x120 cms in flooring, treads of steps and landing laid on a bed of 12 mm thick cement mortar 1:3(1 cement :3sand) finished with flush pointing in white cement complete in all respect including carriage of material in all leads & lifts.

Providing and fixing 19mm thick water proof marrine ply centuary/virgo/green make in shelves/box for cup board with butt joints & fixing with nails & screws etc complete in all respect including carriage of material in all leads & lifts.

Providing and fixing 19mm thick water proof commercial board .Centuary/virgo/green make in shutter of cub board (Bhuttan make)with butt joints & fixing with nails & screws etc complete in all respect including carriage of material in all leads & lifts.

Providing and fixing 6mm thick burl ply of standard quality and of approved shade & design wall lining i/c fixing with approved adhesive, butt jointing and nails & screws complete (Base frame work to be measured & paid for separately) complete in all respect including carriage of material in all leads & lifts.

Providing and fixing 1.00mm thick coloured or plain lamination sheet (sunmica) virgo/merrino make on boards/ ply wood sheets with approved adhesive and nails etc complete in all respect including carriage of material in all leads & lifts.

Providing and fixing square edges cover fillets (beading) 19mmx6mm section i/c mitring at junctions with wood screws and nails complete in all respect including carriage of material in all leads & lifts. 1st class deodar wood

Providing and fixing bright finished stainless steelsliding door-bolts with nuts and screws etc. complete in all respect including carriage of material in all leads & lifts.

Providing fixing bright finished stainless steel tower bolts (barrel type) with screws etc. complete. in all respect including carriage of material in all leads & lifts.

Providing and fixing bright finished stainless steel handles for doors with screws etc. complete. in all respect including carriage of material in all leads & lifts

Providing and fixing bright finished hard drawn hooks and eyes complete in all respect including carriage of material in all leads & lifts. 150 mm

P/F bright finished brass Godrej /Hettich make mortie lock with all acessories 150 mm size complete in all respect including carriage of material in all leads & lifts.

P/F Heavy duty hydraulic door closer Godrej make/Hettich make complete in all respect including carriage of material in all leads & lifts.

Providing and laying cement concrete 1:6:12(1cement:6sand:12 graded crushed stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth ( under Floor) complete in all respect including carriage of materials in all leads and lifts.

Providing and fixing 40x3mm flat iron hold fast 40 cm.long including fixing to frame with 10mm diameter bolts,nuts and wooden plug and embedding in cement concrete block 30x10x15cm of 1:3:6 (1cement:3sand:6graded stone aggregate 20mm nominal size)complete in all respect including carriage of material in all leads and lifts.

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting,fixing in position and applying a priming coat of red lead paint. In MS hollow square/rectangluer pipes (tata make)beams joists channels ,angles, tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like complete in all respect including carriage of material in all leads and lifts.

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees including carriage of material in all leads and lifts as required as per the direction of Engineer-in-charge

Providing and fixing ridges or hips 60cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories including carriage of material in all leads and lifts as required as per the direction of Engineer in Charges.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominalsize) complete in all respect including carriage of material in all leads and lifts

Stone filling behind retaining walls complete in all respect including carriage of material in all leads and lifts

Filling in plinth with sand under floors including watering ramming consolidating and dressing complete under flooring complete in all respect including carriage of material in all leads & lifts.

Providing and laying cement concrete 1:5;10 (1cement :5sand :10 graded stone aggregate 40mm. nominal size) with 15 % plum and curing complete excluding cost of form work in retaining walls/ Breast walls, the size of plums shall usually be 150mm. to 300mm. as per H.P.P.W.D. Specification complete in all respect including carriage of material in all leads & lifts

Providing and fixing bright finished brass handles for cup board with screws etc. complete. in all respect including carriage of material in all leads & lifts. 150 mm

Providing and fixing 15 cm. wide 45 cm. overall semi circular plain G.I. sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design including carriage of material in all leads & lifts. 0.80mm thick sheet.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete in all respect including carriage of material in all leads & lifts.

Applying one coat of Acrylic primer (Spectrum or equivalent of Superior quality) on new concrete/ masonry/plastred surfaces after and including preparing the surface by thoroughly brushing the surface free from mortar droppings and other foreign matters, sand papering the surface smooth complete complete in all respect including carriage of material in all leads & lifts.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete in all respect including carriage of material in all leads & lifts.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including t horoughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface complete in all respect including carriage of material in all leads & lifts

Polishing two coats with PU(poly utherene) polish of required shade on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt, dust and sand papered smooth and including a coat of wood filler complete in all respect including carriage of material in all leads & lifts.

Applying spirit or oil stains any colour on wood and wood based surfaces(sirca-light wall nut shade) to give an even surface including cleaning the surface of all dirt/dust required for PU. Poliosh finish,sand papering so as produce a smooth dry and wall surface including stopping and knotting complete.

Applying two coat of wood preservetive on previously treated wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter,sand papering and knotting complete in all respect including carriage of material in all leads & lifts.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting.complete including carriage of material in all leads & lifts Readymixed paint brushing with pink primmer.

Painting two coats(excluding primimg coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping complete in all respect including carriage of material in all leads & lifts other than white enamel paint

Painting two costs (excluding priming coat) on new steel and other metal surfaces eith enamel paint brushin to give an even shade including cleaning the surface of all dirt,dust and other foregin matters complete including carriage of material in all leads & lifts Enamel white paint

Providing and fixing plaster of paris(POP.) false ceiling 12 mm thickplaster, fixed over GI Mesh 5x5mm size, weight min. 0.70kg/sqmt ,GI sections (Min.0.350kg/mtrand wire mesh,:L-connectors, rawl plugs, complete as per Arhitectural drawings complete) all material chetak.Jindal Make),cross and main section ,grid size 45x90cms maximum.complete as per directions of the Engineer-in-charge.

Providing and laying heavy duty precast cement conrete inter locking paver blocks vibro compacted upto M-50 grade ( NTC make) i/c border or kurb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Sub base concrete floor to be paid for 60mm thick inter locking blocks complete in all respect including carriage of material in all leads & lifts

Providing and fixing 6/8 mm thick window glasses Saint Gobin/Equvallent make for fixed portion of windows, fixed with teak wood beading/moulding 40x12mm, complete including carriage of material in all leads & lifts

Providing and fixing stainless steel railing for stairs using 304 grade,Jindel coil, top hand rail 50 mm diameter@ 1.85kg/mtr,40x40mm square balusters @ 1.5kg/mtr,fixed at alternate step, 4 nos 20x20mm horizontal sq.pipes(1.20kg/mtr) welded to balusters, balusters fixed to steps by drilling in tread and fixing of 16mm, bolt 50 mm long and washers complete.

Excavation in earth work and filling in 15cms layers in foundations and plinth i/c ramming,watering and consolidating up to all leads and lifts.

P/Fixing door shutter stopper for wire gauge shutters 100 mm long (stainless steel) including carriage of material in all leads & lifts

P/Fixing rubber block for back door stopper 100 mm size and 50 mm dia including carriage of material in all leads & lifts

Pdg and fixing of Hydraulic ultra luxury elevator lift 8 persons 408kg rated capacity automatic centre opening doors including carriage of material in all leads & lifts

Provision for structural drawings and design of building and safe bearing capacity of soil complete in all respect as per direction of the Engineer-in-charge.

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. Group-C

Wiring for light plug with 2x1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Supplying & fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required:-

4 modules(140mmx78mmx50mm)

6 modules(205mmx78mmx50mm)

8 modules (120mmx135mmx60mm)

12 modules (205mmx135mmx60mm)

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2x1.5 Sq. mm.

2x2.5 Sq. mm.

2x4.0 Sq. mm.

Wiring for circuit / sub-main with 4x6 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.6 Sq.mm. (4x6+2x6) HRFRLS/PVC insulated single core copper conductor cable for earthing wire from MCB box to main pannel board.

Wiring for circuit / sub-main with 4x10 Sq. mm. PVC insulatedheat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.10 Sq.mm. (4x10+2x10) HRFRLS/PVC insulated single core copper conductor cable for earthing three phase wiring in main pannel board for busbar.

Supplying and fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

S.P. 5/ 6 Amps one way Modular switch.

5 pin, 5/ 6 Amps Modular socket outlet.

Bell push, Modular.

Supplying and fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

S.P. 15/ 16 Amps one way Modular switch

6 pin,15/16 Amps Modular socket outlet.

Supplying and fixing TV. Socket outlet, modular rating switch /socket in the existing switch box / cover plate including connections etc. as required.

Supplying and fixing Telephone socket outlet, modular rating switch /socket in the existing switch box / cover plate including connections etc. as required.

Supplying and fixing ceiling rose on the existing junction box /wooden block including connections etc. as required.

Supplying and fixing of Double door-12 way single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wireset, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnec- tions, phosphatized and powder painted, including earthing etc. as required.

Supplying and fixing 63 Amps. Cat-A rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing sheet metal bus-bar chamber suitable for 200 Amp. 415 volts capacity with 4 No. copper strip bus-bars each of length 450mm & cross-sectional area(25.4mmx4.75mm), enclosure made from 1.6 mm thick M.S. sheet having overall dimensions (530mmx450mmx 150mm) nominal with all accessories including connections, earthing the body etc. as required.

Providing and fixing TP&N switch disconnector fuse unit cubical type, 415/500 volts with 3 No. HBC/HRC fuses, in sheet steel enclosure including drilling holes on the board, connections, earthing the body etc. as required. 100 Amp. Category-A

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of Single pole & neutral. Cat-B in the existing MCB DB complete with connections etc. as required.

Supplying and erection of wall mounted metal boards for switch gear mounting of suitable size, with permissible variation in size of plus minus 5mm, welded frame work made of M.S. angle iron 35 mm x 35 mm x 6 mm thick duly welded complete with 2.80mm thick M.S. sheet fixed with hinges as open able front, complete with locking arrangement including painting and bonding to the existing earth as required:-

Supplying and erection of 40/50/63 amps rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of Double pole. Cat-B in the existing MCB DB complete with connections etc.

Supplying and fixing 40 Amps. Cat-B rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 Amps, 240 volts, SPN industrial socket outlet, 2-pole & earth, metal enclosed plug top, sheet steel enclosure, suitable to accommodate a 20 Amp SPN-MCB/DP, on surface or in recess, with chained metal cover for the socket outlet, complete with connections, testing and commissioning etc. as required.

Providing and fixing TP&N switch disconnector fuse unit panel mounting, 415/500 volts with 3 No. HBC/HRC fuses, open execution, including drilling holes in the cubical, making connections, etc. as required. 200 Amp. Category-A

Earthing with copper earth plate 600 mmx600 mmx 3 mm thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia. 300 mm long copper tube, having single prong at top, with 85 mm dia 3 mm thick copper base plate including holes etc. complete as required.

Supplying and fixing copper tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required ( for vertical run)

Supplying and fixing copper tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required ( for horizontal run)

Providing and fixing M.V.danger notice plate of 200 mm x 150 mm made of mild steel at least 2 mm thick, and vitreous enameled white on both sides and with inscription in signal red color on front side as required.

Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, rmoured/ XLPE power cable, working voltage 1100 volts grade direct in ground; to be laid 1 meter below the ground level including excavation sand cushioning, protective covering and refilling the trench etc. of the Armoured cable 4 sq. mm (twin core) for Yard lights.

Providing and installation of stationary storage type Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and fixing of Nonreturn valve, Dead weight safety valve, 2 No C.P. connection rods 18" long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc. 25 Liter capacity water heater (Cat-A)

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. Ceiling Fan 1400 mm sweep, Category-A

Providing and installation of Exhaust Fan, Light duty, (Domestic) 225 mm sweep in the existing opening, including taking the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc.

Providing and fixing 2 x36 watt-LED Panel surface mounting /recessed type light fixture 60x60cms size syska/jaquar make.

Supplying and fixing of fancy wall bracket containing thread type LED lamp holder (s) of all sizes and shapes, complete with all accessories but excluding LED lamp including making connections, testing etc. as required. Fixed type wall bracket 150 dia, single lamp.(Category-A)

Providing, Installation, testing and commissioning of prewired flourecent tube fitting 1x20W LED coplete in all respect.

Supplying and fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase,230 volts complete as required

Supplying and fixing LED BULBS 11 watt suitable for D.C./A.C. single phase,230 volts complete as required

Supplying and drawing co-axial TV cable,RG-6 grade,0.7mm (75 Ohms) copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed, steel / PVC conduit as required.

Supplying and fixing bakelite batten/angle holder including connections etc. as required.

Supplying and fixing of integral LED Post Top Lantern of following capacity, cast aluminium spigot, spun aluminium canopy, opal acrylic diffuser, complete with all accessories but excluding CFL lamp including making connections, testing etc. as required. Gate post top lantern - CLED 22 watt.

Supplying and fixing stepped type Modular fan regulator on the existing modular box including making connections etc. as required.

Supplying and fixing of INTERCOME exchange of reputed brand having 20 connections with sets

Supplying and fixing of split type air conditioner Blue star/havells/carrier make having two stars features auto clean filter four wayu swing all copper pipes including making provision of draining of back moisture water through GI pipe 20mm dia electronic voltage stabilizer, cutting holes for conduits in wall, unit bracket set fixed on outer wall complete as required

1.50 Tonne capacity

2.00 Tonne Capacity

Providing and fixing boundary lights 20x30cms clear light fixture, top mounted,with 20 watt LED bulb.

Providing and fixing high pressure spigot and socket waste ventilating pipe of following daimeter i/c entire carriage of material within all leads and lifts.

75mm dia

100mm dia

Providing and fixing PVC plain bend of following diameter i/c entire carriage of material within all leads and lifts.

75mm dia

100mm dia

Providing and fixing PVC door bend of following diameter i/c entire carriage of material within all leads and lifts.

75mm dia

100mm dia

Providing and fixing PVC collar/ socket of following diameter i/c entire carriage of material within all leads and lifts.

75mm dia

100mm dia

Providing and fixing PVC Single equal brach of following diameter i/c entire carriage of material within all leads and lifts.

75mm dia

100mm dia

Providing and fixing PVC Single equal brach with oval access of following diameter i/c entire carriage of material within all leads and lifts.

75mm dia

100mm dia

Providing and fixing PVC Floor traps 110x75mm i/c entire carriage of material within all leads and lifts.

Providing and fixing viterous China wash down water closet (European Type WC pan) with intergral S” trap including jointing the trap with soil pipe in cement mortar 1:1 (1cement: 1 sand) including entire carriage of material within all leads and lifts.(JAQUAR/CERA MAKE)

Wall mounted EWC with full frame, built in concealed cystern,seat cover,cistern push button.

Providing and fixing viterous China wash down water closet (European Type WC pan) with intergral “P”or”S” trap including jointing the trap with soil pipe in cement mortar 1:1 (1cement: 1 sand) including entire carriage of material within all leads and lifts.

One piece WC .wall distance 300 mm/250mm JAGUAR/CERA MAKE

Providing and fixing vanity type wash basin 80x50x70cms, somany make,stainless steel body.

Providing and fixing vitreous china wash basin with pedestal , single hole for mixture tap with CI or MS brackets painted white i/c cutting holes & making good the same but excluding fitting i/c entire carriage of material within all leads and lifts. Cera make Concord, 630x450mm size.

Providing and fixing of M.I. union for wash basin 32mm dia i/c carriage of material within all leads and lifts.

Providing and fixing 32mm dia PVC waste pipes for wash basin i/c brass check nut i/c entire carriage of material within all leads and lifts.

Providing and fixing 90x60cms. bevelled edge mirror of superior glass mounted on 6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washer including carriage of materials within all leads and lifts.

Providing and fixing C.P. brass towel rail complete with C.P.brass brackets fixed to wooden plugs with C.P. brass screws including carriage of materials within all leads and lifts 600 x 20mm.

Providing and fixing 600x120mm glass shelf i/c entire carriage of material within all leads and lifts.

Providing and fixing CP toilet paper holder i/c entire carriage of material within all leads and lifts.

Providing and fixing CP brass soap dish i/c entire carriage of material within all leads and lifts.

Providing and fixing Tooth brush and tumbler holder i/c entire carriage of material within all leads and lifts.

Providing and fixing CP brass shower 250mm dia,with 60 cms long rod, i/c entire carriage of material within all leads and lifts.

Providing and fixing brass bib tap long nose 15 mm dia (Heavy duty) i/c entire carriage of material within all leads and lifts.

Providing and fixing brass bib tap short body 15 mm dia (Heavy duty) i/c entire carriage of material within all leads and lifts.

Providing and fixing brass angle valve 15 mm dia without nut and pipe i/c entire carriage of material within all leads and lifts.

Providing and fixing CP concealed stop cock 15 mm dia without nut and pipe i/c entire carriage of material within all leads and lifts.

Providing and fixing single hole single lever wash basin mixture i/c entire carriage of material within all leads and lifts.

Providing and fixing PVC connection 15mm dia i/c entire carriage of material within all leads and lifts.

Providing and fixing 100mm dia, C.P. brass grating including carriage of material within all leads and lifts.

Providing and fixing Jet connection ,health facut ,fixed for WC seat i/c entire carriage of material within all leads and lifts.Jaquar.

Providing and fixing CP towel ring i/c entire carriage of material within all leads and lifts.

Providing and fixing CP towel rack 600x250mm for VIP toilet i/c entire carriage of material within all leads and lifts.

Fixing to wall ceiling and floor galvanised mild steel tubes (light grade), tube fittings and clamps i/c making good wall ceiling & floor of following diameter i/c entire carriage of material within all leads and lifts

15mm dia

20mm dia.

32mm dia

Providing & fixing Brass full way wheel valve i/c entire carriage of material within all leads & lifts

20mm dia

32mm dia

Providing and fixing 115x50x25cms size double bowl of approved make stainless steel kitchen sink i/c entire carriage of material within all leads and lifts.

Providing and fixing 2000 ltrs. Double layer sintex make water storage reservoir with top lid and making connection complete in all respect including all leads and lefts.

Constructing manhole with RCC top slab in 1:2:4 mix ( 1 cement :2 sand:4 graded stone aggregate 20 mm nominal size) foundation concrete 1:4:8 ( 1cement:4sand :8graded stone aggregate 20 mm nominal size),inside plastering 15 mm thick with cement mortor 1:3 (1cement:3sand),finished with a floating coat of neat cement & making channels in cement concrete 1:2:4 (1cement:2 sand:4 graded stone aggregate 20mm nominal size) finished smooth complete i/c curing &testing. (i) inside size 1200 x 900 x 1000 mm deep i/c c.i. cover with frame (m. duty) with single pattern 455 x 610 mm internal dimensions (total wt.of cover & frame to be not less than 38 kg) 23 cms. thick brick masonry walls using 2nd class brick in cm 1:3 (1cement : 3 sand).

Providing & fixing stone ware gully trap grade 'A' complete with CI grating,B/Masonry chamber in cement mortor 1:5 & water tight CI cover with frame of 300 mm x 300 mm size (inside) .The wt.of cover to be not less than 4.53 Kg & frame to be not less 2.72 Kg. (Square mouth traps 100 x 100 mm size)

Mukesh Ranjan Contractors Pvt Ltd

Sushant Puri

MS Kamal Dev Sharma

gagan ohri

Subham Mahajan

PANKAJ KUMAR