CERTAIN REPAIR TO MISC B/R WORKS, FALSE CEILING, FLOORING, PLUMBING, JOINERY WORK, ROOF SHEETING AND CONNECTED ITEMS AT 8 FBSU AF, AWANTIPUR

Amount

Dismentalling of plain or corrugated steel sheeting of any gauge, thickness etc. in roof coverings/ cladding/ eaves etc., complete all as specified and directed.

S&F galvanised corrugated mild steel sheeting, with two corrugation side lap fixed with 'L' type or 'J' type or cranked hooked bolts with washers in roof, 0.63mm thick, grade-O quality, with 120 grms/sqm zinc coating and grade 'B' Class 8, complete all as specified and directed by Engineer-in-Charge.

S&F Galvanised plain mild steel sheeting 0.63mm thickness fixed with 'L' type or 'J' or cranked hook bolts with washers, in roofs as in ridge etc., complete all as specified and directed.

Refixing Plain or corrugated steel sheeting, any gauge, thickness, roof coverings with two corrugation side lap fixed with L' type or 'J' type or cranked hooked bolts and dome type bitumen washers, complete all as specified and directed. Note:- Serviceable sheets obtained under item No 01 above shall be re-used.

Dismantling of timber scantlings less than 40 sq. cm in section as in fillets, rails, cupboard frame etc., complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortor bedding (but not backing) removing the rubbish of the premises, complete all as specified and directed.

M&L 25mm PCC 1:2:4 Type B-0 (Using 12:5mm stone agg) as in sub base floor, complete all as directed and specified.

M&L coloured/ printed non skid ceramic tiles 7 to 8 mm thick area of each tiles exc 0.18 sqm but not exc 0.38 sqm, laid in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick bedding layer in cement mortar (1:4) including necessary cutting and waste as per site requirement, complete all as specified and directed by Engineer-in-Charge.

All as per Srl Item No. 8 but on vertical surfaces such as skirting including 9 to10mm thick rendering in cement mortar 1:3 rough finish to receive the tiles, complete all as specified and directed.

M&L coloured/ printed non skid ceramic tiles 7 mm thick (square/ rectangular) area of each tile exc 0.11 but not exc 0.16 sqm laid in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement, complete all specified and directed.

M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/ shade) of 450x300x7mm/ 350x 250x 7 mm/ 450X 350X 7mm thick in vertical surfaces, as in dado/skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, over and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles, complete all as specified and directed.

M&L for 18-20mm thick granite stone (slab) of any colour/type, (table rubbed and polished) work as in floors/ vertical surfaces, cooking platforms and like, set in neat cement including pointing in white cement with admixture of pigment to match with shade of granite, complete laid over and including 15mm thick screed bed in cement mortor (1:6) laid and jointed with grey cement slurry mixed with pigment, complete all specified and directed.

Demolition of cement concrete to ground floor(unreinforced) and paving n.exc 15cm thickness (below or above ground level) and removing rubbish of out side MOD land, complete all as specified and directed.

M&L 75 mm thick PCC (1:3:6) type C-2 using 40mm graded aggregate as in plinth protection even and smooth without using extra cement, complete all as specified and directed.

M&L 100mm thick Cement concrete 1:2:4 Type B-2 (using 40mm graded stone agreegate) as in sub base of flooring, complete all as specified and directed.

M&L Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment and including screed bed of 20mm thick in CM (1:4) etc., complete all as specified and directed.

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and including 15mm thick screed bed in cement mortor (1:6) laid and jointed with grey cement slurry mixed with pigment, complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations, complete all as specified and directed.

Taking down Chowkhats or frames not exc. 1.5 sq. m each (without taking off shutters from the frames), complete all as specified and directed.

Taking down shutters of any description exc. 1sqm and not exc. 2 sqm each, but refixing of shutters in same opening, of any descriptions exc 1.0 sqm but.n.exc 2 Sqm each, complete all as specified and directed.

S & F gaurd bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain/square, let in and fixed with flate iron or wall frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165, complete all as specified and directed.

M&L for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc. 0.5 Sqm in each pane incluing Hacking out old broken glass (any thickness, size, quality or description) from metal frame incl punching or drilling out old glazing pins/spring clips, complete all as specified and directed.

M&L for 3mm thick sheet figured glass, pin headed type and glazing with oil putty in square n.exc. 0.5 Sqm in each pane including Hacking out old broken glass (any thickness, size, quality or description) from metal frame incl punching or drilling out old glazing pins/spring clips, complete all as specified and directed.

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Framed work as in false ceiling, doors or gates of angle or other section with gusset plates, rails, braces, etc. complete drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-410 grade, complete all as specified and directed.

Dismantling wall and ceiling boards (fibre pulp, insulation, etc.) or insulation board/ slabs/ blankets any thickness including grid work/ aluminium frame work, cover fillets, complete all as specified and directed.

Prelaminated particle board 9mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination with all around 6mm thick teak wood beading as in false ceiling fixed to metal frame, complete all as specified and directed.

Demolition of brick or stone boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone works and precast concrete articles, complete all as specified and directed

M&L Brick work with sub class B bricks ,straight or curved on plan exc 6m mean radius built in CM 1:6, complete all as specified and directed.

Brick work with old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed.

Taking down Cement Plaster, any description on Brick Walls or on Concrete Surfaces including raking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of concrete/brick interior surfaces in cement mortar 1:6 as per manufacturer's instruction, finished fair and even without using extra cement, complete all as specified and directed.

M & L Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 on wall surfaces, finishing the surface even and smooth without using extra Cement, complete all as specified and directed. Note:- Integral water proofing compound shall be measured and paid for separately.

M&L preparation of newly plastered wall surface and applying of Birla/ JK white wall putty approx 3mm thick in two layer as per manufacturer's instruction on existing prepared surface and make the surface smooth by rubbing with sand papers and applying two coats of oil emulsion distemper over a coat of primer, complete all as specified and directed.

Preparing new plastered or un-plastered surfaces of walls and applying two coats Acrylic exterior emulsion paint in camouflaging (Disruptive) pattern (Green, Grey & Brown colour) over a coat of acrylic primer, complete all as specified and directed.

Preparation of new surfaces of steel or iron work or CGI/ PGI sheeting in walls or roofing, over 10cm width or girth, not otherwise described and applying two coat of synthetic enamel paint in camouflaging (Disruptive) pattern in three colours (Green, grey and brown) over a coat of acrylic primer, complete all as specified and directed.

Preparation of old painted surfaces of steel or iron work or CGI/ PGI sheeting in walls or roofing, over 10cm width or girth, not otherwise described and applying one coat of synthetic enamel paint in camouflaging (Disruptive) pattern in three colours (Green, grey and brown), complete all as specified and directed.

S & F in repair Stainless Steel Wall Mount Case with Soap Dish & Brush Holder fixed to wall, complete all as specified and directed.

S&F in repair Ball valves 20 mm high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed, complete all as specified and directed. (Minimum weight 15mm-142gms/ 20mm-210gms./ 25mm-455gms/ 40mm - 690 gms)

S&F CP health faucet of 1.25Mtr long CP flexable tube with necessary fittings, complete all as specified and directed.

S & F in repair curtain rails of stainless steel with fixing brackets, stops, rollers, funnels etc., complete all as specified and directed.

S&F in repair PVC flushing cistern 10 ltr capacity white with all internal fittings including brackets PVC connection 45cm long including nut and PVC washer at both ends including 32mm bore PVC long bend flush pipe 90cm long, complete all as specified and directed.

S&F in repair Vitreous China wash down water closet (pedestal pattern), White/coloured including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover and chromium plated jet including PVC connection, fixed complete including demolition of old unservicable WC and provision of plain cement concrete M-15, type B-I, using 20mm graded crushed stone aggregate, fixed in repairs, complete all as specified and directed.

S & F Vitreous china wash hand basin coloured, flat back type of size 550mm x 400mm including waste pipe & plug, porcelain stopper, 32mm dia PVC waste pipe with CP brass coupling and set of bracket, complete all as specified and directed.

S&F for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, suppling and fixing at site as per specification & drawing, complete all as specified and directed.

S&F of factory Made Solid panel PVC door shutter, 28 to 30mm thick (stiles) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded and wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900) used instead of exposed portion of PVC sheet beading plain colour PVC sheets for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, suppling and fixing in the frame at site as per specification & drawing, complete all as specified and directed.

S&F 100 mm long stainless steel butt hinges with stainless steel screw, complete all as specified and directed.

S&F extruded aluminum alloy handles of size 150mm fabricated type anodised, complete all as specified and directed.

S&F Aluminium alloy anodised barrel tower bolts of extruded section 150 mm long and fixed, complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt size 200mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Taking up or down 15 mm dia steel tubing in wall, ceiling or floor and connections, including cleaning for refixing or removal to store etc., complete all as specified and directed.

All as per Srl item No. 51 above but 20 mm dia of pipe, complete all as specified and directed.

S&F 15 mm dia medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

All as per item No. 53 above but bore of pipe 20mm dia pipe, complete all as specified and directed.

Cutting chases, pinning for concealed water tubing and making good to facing where required and pointing in cement mortar 1:3, cutting exc. 10cm but n.exc 20cm girth, complete all as specified and directed.

S&F in repair 20mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed.

S&F 500 litre capacity rotational moulded polyethylene water storage tank (cylindrical vertical double layered with closed top) duly provided with necessary fittings/ fixtures for connecting inlet, outlet, washout and overflow pipes; hoisted and fixed in position incl dismantling PVC water sotrage tanks of capacity more than 250 to 500 litres capacity, complete all as specified and directed.

M&L for disconnecting existing moulded polythelene water storage tank, setting aside (or lowering if required) for repairs, cleaning etc. and hoisting if require re-connecting and re-fixing in position exc. 250 & n.exc. 500 ltr, complete all as specified and directed by Engr-In-Charge.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed.

S&F in repair 15mm dia 450mm long PVC connection with brass nut and washer, complete all as specified and directed.

S&F in repair 15 mm bore CP Bib tap cast copper alloy fancy type crutch or butterfly handles screwed down for iron or for brass ferrule, complete all as specified and directed.

S&F in repair stop valve/ angle valve, fancy type, chromium plated, cast copper alloy screwed down, high pressure, with crutch or butterfly handle of 15mm dia. Screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed.

S & F in repairs Stop cock/ two way Stop 15 mm bore cast copper fancy type chromium plated alloy screwed down high pressure with crutch or butter fly handle serwed both ends for iron pipe or for unions, complete all as specified and directed.

S&F in repair Brass CP central hole wash basin mixer for hot & cold for 15mm dia complete fixed to connection, complete all as specified and directed.

S&F in repair Brass CP sink mixer for hot & cold for 15mm dia complete fixed to connection, complete all as specified and directed.

S&F in repair chromium plated brass wall mixer 3-in-1 fancy type with provison for both hand shower and overhead shower complete with wall flange (without hand &over head Shower screwd down for 15 mm GI bore pipe, complete all as specifed and directed.

Supply and fixing in repair Shower Rose brass cromium plated 125mm size with arm suitable for 15mm dia pipe, complete all as specified and directed.

S&F PVC (SWR) pipes single socketed,75mm bore, in any length with rubber ring joints fixed to wall and floor, complete all as specified and directed.

PVC (SWR) 75mm bore (dia), Bends, any radius with access door and Jointing with Solvent Cement and fixed-in-repairs, complete all as specified and as directed.

S&F in repairs CP grating round suitable for 110 mm dia and connecting up, fixed in repairs, complete all as specified and directed.

Note :- An amount of Rs. 46,020.00 on account of credit schdule for Sch 'A' Part-II Shall be deducted from the total amount of BOQ to arrive at the contract sum.

M/S GEE EMM MIR (BID ID -3099754)

MS Ghulam Hassan and Sons (BID ID -3096758)

M/S ABBAS M. ENTERPRISES (BID ID -3096420)

M/S LATIF AHMED MIR (BID ID -3105598)

M/s M Ashraf and Brothers (BID ID -3118172)