REPAIR AND MAINT TO EXTERNAL SERVICES LIKE PATHS HARDSTANDING COMPOUND WALLS FENCING INCLUDING CERTAIN MISC B AND R WORKS ALOGWITH REPAIRS TO ROOF SHEETS FALSE CEILINGS AND OTHER ALLIED WORKS AT VRDE AHMEDNAGAR

Amount

REPAIR AND MAINT TO EXTERNAL SERVICES LIKE PATHS, HARDSTANDING, COMPOUND WALLS, FENCING INCLUDNG CERTAIN MISC B/R WORKS Dismantling floor, hearth or wall tiling including cement mortor bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness below or above ground level unreinforced complete all as specified and directed.

Demolition of reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness below or above ground level complete all as specified and directed.

M & L for 75 mm thick PCC 1:2:4 type B2 (using 40 mm graded stone aggregate) as in hard standing finished even and smooth without using extra cement complete all as specified and directed.

M & L for hardcore of broken stone or boulders of guage exceeding 63 mm but not exceeding 100 mm deposited, spread and levelled in layers not exceeding 15 cm thick watered and rolled/rammed to a true surface complete all as specified and directed

Supply only broken glass beads of size 60 to 80 mm (approx) fixed in plinth protection below concrete complete all as specified and directed.

M & L for 75 mm thick PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as in plinth protection finished even and smooth using extra cement complete all as specified and directed.

Forming contraction (Dummy) joints 65 mm deep x 10 mm wide, filled with sealing compound grade 'A' complete all as specified and directed.

M & L for 75 mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base of floor finishes complete all as specified and directed.

M & L for 25 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in floor finishing complete all as specified and directed

Providing and Laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in reqd colour & pattern over and incl 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per reqd size & pattern, finishing and sweeping extra sand complete all as specified and directed.

M & L for Reinforced cement concrete nominal mix 1:2:4 type B1(using 20 mm graded stone aggregate) as in chajjas complete all as specified and directed

M & L for non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors/terraze etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer for laying floor/terraze tiles in CM (1:6) complete all as specified and directed.

Excavation in post holes each not exceeding 0.50 cum getting out, returning filling and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm watering and removing surplus soil to a distance not exceeding 50 mtr and making good surface in hard/dense soil complete all as specified and directed.

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation or for manholes etc not exceeding 10 sqm on plan and not exceeding 1.5 m deep and getting out in hard/dense soil complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming layers not exceeding 25 cm thick soil complete all as specified and directed.

Removing of surplus excavated soil to a distance not exceeding 50 mtrs and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

M & L for PCC 1:4:8 type D2 (using 40 mm graded stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

M & L form work to sides of concrete foundations, footings, rafts, plinth beams etc of rough finished surfaces of flat complete all as specified and directed

M & L form work to sides of concrete columns, pillars etc of fair finished surfaces of flat complete all as specified and directed

M&L for Formwork to flat surfaces of soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work exceeding 200mm thick complete all as specified and directed.

M&L for Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc vertical or to batter complete all as specified and directed.

M & L for reinforced cement concrete nominal mix 1:2:4 type B1 (using 20 mm graded stone aggregate) as in foundation footings of columns, beams, raft etc complete all as specified and directed.

M & L for reinforced cement concrete nominal mix 1:2:4 type B1 (using 20 mm graded stone aggregate) as in columns, pillars, piers, posts etc complete all as specified and directed.

M & L for reinforced cement concrete nominal mix 1:2:4 type B1 (using 20 mm graded stone aggregate) as in Walls, retaining walls, basement walls, ballast walls and the like;any thickness; above top of footings; including attached pilaster and buttresses complete all as specified and directed.

M & L for reinforced cement concrete nominal mix 1:2:4 type B1 (using 20 mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specfied and directed.

M & L for granite tile of size 600 x 300 x 12 mm thick machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including nosing, grinding and polishing complete over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

S & F rolled mild steel joist, channel, angle or tee sections fixed without connecting plates etc quality confirming to Fe-410-W (Gde E-250) quality-A all as specified and directed

S & F rolled mild steel framed work as in doors or gates of angle or other section confirming to Fe-410 S with gusset plates, rails braces etc complete drilled and fixing of steel sheeting or other covering and hanging and fixing complete all as specified and directed.

M & L for lettering with chromium plated steel sheeting 1.00 mm thick and of size not less than 30 cm each including fixing on pillars, posts etc all as specified and directed

M & L precast reinforced cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) in 35 mm thick jallies or louvers including all mouldings and set in cement mortor 1:4 complete all as specified and directed.

M & L for rendering 15 mm thick cement plaster on fair faces of stone masonry surfaces other than fair faces of brick or concrete surfaces in CM 1:6 finished the surfaces even and fair without using extra cement complete all as specified and directed.

M & L for newly prepared plastered surfaces of any description and applying two coats of cement based paint over a coat of chalk whitening primer on wall surfaces complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5 mm to upto and including 10 mm dia cut to length, bent to shape required as in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

Supply only GI chain link galvanised fencing any size or type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails straining bolts etc including provision of binding wire complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortor including all quoins, arches, pillars etc but excluding ashlar facings and dressed stone work complete all as specified and directed.

M & L for stone walling of randam rubble uncoursed, well bonded and solidly hearted built in cement mortor (1:6) complete all as specified and directed.

All as per ser item no 40.00 above but except stone complete all as specified and directed.

M & L for stone keyed pointing to randam or polygonal rubble uncoarsed or brought upto courses in cement mortor (1:4) complete all as specified and directed.

Dismantling mild steel work, wire and coil work of any description not otherwise provided for complete all as specified and directed.

S & F mild steel angle posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire etc) including all necessary drilling, bolting or rivetting etc, and similar work confirming to Fe-290 Grade E-165 complete all as specified and directed

S & Fixed in repairs galvanised 2 strand steel barbed wire 2.24 mm dia of barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to angle fencing above compound wall and any type, including securing or tying at crossings with and provision of galvanised mild steel wire staples or steel pins etc complete all as specified and directed. (each line of wire to be measured).

S&F stainless steel rollers V Groove Wheel, Roller Wheel of grade SS 304 Stainless Steel Heavy Duty Track Wheel, Detachable Duplex Bearing fixed for Swing Sliding Gate, V Type Pulley Block. Wheel Diameter 48mm(1.9 inch). Overall Height 54mm(2.1 inch). Overall Width 30mm(1.18 inch). Groove Width 16mm( 0.62 inch). Groove Depth 12mm, for Wire/Rope Diameter not exc. 10mm. For sliding gates including bearings fixed in position including taking down the existing gate,shutter and refixing the shutter after fixing the roller with and including welding,screwing or other suitable means as per site condition complete all as specified and directed.

Repairing,servicing and oiling to existing sliding gate motor including fixing in position neatly and also including following : (i) Replacing old and fixing new central moving rod with installation as per length of gate (ii) Replacing Old and fixing new gate wheels 02 Nos SS 304 grade heavy duty wheel with double bearing of size 100mm (iii) Replacing old and fixing new nylon guide roller 06 Nos for support of gate for increasing the performance Complete all as specified and directed.

S & Fixed in repairs galvanised concertina coil, of suitable diameter with following specification : (i) Thickness of barb - 0.5mm (ii) Wire diameter - 2.5mm (iii) Barb Length - 22mm (iv) Barb width - 16mm (v) Barb to barb spacing (c/c) - 35mm (vi) Heavy galvanised high tensile spring steel wire as per IS-4454 including galvanized coating 160gms zinc per Sqm by manufacturer, complete all as specified and directed.

M & L preparation of newly prepared steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed

REPAIR TO ROOF SHEETS , FALSE CEILINGS AND OTHER ALLIED WORKS Dismantling plain or corrugated steel sheeting, any guage, thickness including Nainital or similar pattern roof coverings complete all as specired and directed

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specired and directed

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillets complete all as specired and directed

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheets 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specired and directed

All as per item No 53.00 above but except sheeting (any thickness) complete all as specired and directed

S & F pre-painted galvalume aluminium zinc coating GI based plain steel sheets 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall/ridge for roof, fixed with self tapping screws complete all as specired and directed

M & L 6 mm thick asbestos cement, corrugated or semicorrugated sheets in roofs, walls etc and fixed with L type or J type or cranked hook bolts complete all as specified and directed

All as per item No 56.00 above but except sheeting (any thickness) complete all as specired and directed

M & L asbestos cement two piece adjustable plain wing ridge of 6 mm thick and fixed with L type or J type or cranked hook bolts complete all as specired and directed

S & F anodised aluminium snap grid frame size of grid 605 x 605 mm work for false ceiling complete all as specified and directed.

M & L for 12 mm thick non asbestos fibre cement building boards fixed or laid/inserted to timber/GI/Aluminium frame work as in ceiling flat or sloping complete all as specired and directed

S & Fixed in repairs 12 mm thick medium density fibre board, exterior grade, fixed to Aluminium frame work with screws complete all as specired and directed

M&L for coloured seamless PVC sheets as in false ceiling of size 3.05mx0.25mx8-9mm thick ( hollow thickness) including aluminium grid of "H","U" & "L" section ( 40mm x 25mm) of 1mm thick in ceiling fixed with screws or solvent chemicals/adhesives as per manufacturer's instructions complete all as directed & directed by the manufacturer. Note : Pattern,design and colour shade shall be as directed by EIC.

S&F 0.16 mm thick sun control reflective film self adhesive type fixed at positions shown including necessary cutting and fixing neatly. One side of sheet shall be mirror faced reflective type and from inside visible type complete all as specired and directed Make : M/s Garware & imported, 3M or equvivalent & approved.

S&F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specired and directed

S&F 100mm size Brass Mortice lock,vertical type complete all as specired and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

S & F joist, channel, angle or tee sections, fixed independently, without connecting connecting plates, etc., (cut to ordinary lengths i.e, within 20 mm of length indicated) confirming to Fe-410W (Gde E-250) quality -A complete all as specired and directed.

S & F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc confirming to Fe-410-W(Gde E-250) quality - A complete all as specired and directed

S & F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment confirming to Fe-410-W (Gde E-250) quality - A complete all as specired and directed

S & F mild steel screw bolts (machine made) with hexogonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexogonal or square nut exceeding 5 cm and not exceeding 10 cm and dia of neck 11 to 15 mm size complete all as specired and directed

M & L preparation of newly prepared steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specired and directed

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm in each complete all as specired and directed

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 sqm but not exceeding 4.00 sqm in each complete all as specired and directed

S & F for solid PVC door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening complete all as specired and directed

S & F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, and fixing in the frame at site complete all as specired and directed

S & F for butt hinges, medium weight, cold rolled of stainless steel of size 100 mm complete all as specired and directed

S & F 150 mm long aluminium, anodised barrel tower bolts of extruded section and fixed complete all as specired and directed

S & F extruded aluminium alloy handles, fabricated type anodised of 150 mm size complete all as specired and directed

Santosh Popatrao Sarode

Abhiraj Enterprises

Nirmal Constructions

DESIRES ENGINEERS &CONTRACTORS